WIPER & WASHER SECTION WW CONTENTS DRIVER CONTROLS WW-1 BASIC INSPECTION... 3 FUNCTION DIAGNOSIS... 6 ECU DIAGNOSIS...31 COMPONENT DIAGNOSIS...

Transcription

1 DRIVER CTROLS SECTI WW A WIER & WASHER B C D CTENTS E BASIC INSECTI... 3 DIAGNOSIS AND REAIR WORKFLOW... 3 Work Flow...3 FUNCTI DIAGNOSIS... 6 FRT WIER AND WASHER SYSTEM... 6 System Diagram...6 System Description...6 Component arts Location...9 Component Description...10 DIAGNOSIS SYSTEM (BCM)...11 COMM ITEM...11 COMM ITEM : Diagnosis Description...11 COMM ITEM : CSULT-III Function...11 WIER...11 WIER : CSULT - III Function (BCM-WIER)...12 DIAGNOSIS SYSTEM (IDM E/R)...13 Diagnosis Description...13 CSULT - III Function (IDM E/R)...15 COMENT DIAGNOSIS...18 WIER AND WASHER FUSE...18 Description...18 Diagnosis rocedure...18 FRT WIER MOTOR LO CIRCUIT...19 Component Function Check...19 Diagnosis rocedure...19 FRT WIER MOTOR HI CIRCUIT...21 Component Function Check...21 Diagnosis rocedure...21 FRT WIER AUTO STO SIGNAL CIR- CUIT...23 Component Function Check...23 Diagnosis rocedure...23 FRT WIER MOTOR GROUND CIRCUIT...25 Diagnosis rocedure...25 FRT WIER AND WASHER SYSTEM...26 Wiring Diagram...26 ECU DIAGNOSIS...31 BCM (BODY CTROL MODULE)...31 Reference Value...31 Terminal Layout...36 hysical Values...36 Wiring Diagram...54 Fail Safe...62 DTC Inspection riority Chart...64 DTC Index...66 IDM E/R (INTELLIGENT OWER DISTRI- BUTI MODULE ENGINE ROOM)...68 Reference Value...68 Wiring Diagram...76 Fail Safe...81 DTC Index...83 SYMTOM DIAGNOSIS...84 FRT WIER AND WASHER SYSTEM SYMTOMS...84 Symptom Table...84 FRT WIER DOES NOT OERATE...86 Description...86 Diagnosis rocedure...86 NORMAL OERATING CDITI...88 Description...88 RECAUTI...89 RECAUTIS...89 F G H I J K WW M N O WW-1

2 recaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT RE-TEN- SIER" recaution for rocedure without Cowl Top Cover recautions Necessary for Steering Wheel Rotation after Battery Disconnect (Early roduction, With Electronic Steering Column Lock) VEHICLE REAIR FRT WIER Exploded View FRT WIER BLADE REFILL FRT WIER BLADE REFILL : Removal and Installation FRT WIER BLADE FRT WIER BLADE : Removal and Installation FRT WIER ARMS FRT WIER ARMS : Removal and Installation FRT WIER DRIVE ASSEMBLY FRT WIER DRIVE ASSEMBLY : Removal and Installation FRT WASHER WASHER TUBE WASHER TUBE : Layout FRT WASHER NOZZLE FRT WASHER NOZZLE : Removal and Installation FRT WASHER NOZZLE : Adjustment WASHER TANK WASHER TANK : Removal and Installation FRT WASHER UM FRT WASHER UM : Removal and Installation FRT WIER AND WASHER SWITCH Removal and Installation WW-2

3 < BASIC INSECTI > DIAGNOSIS AND REAIR WORKFLOW BASIC INSECTI DIAGNOSIS AND REAIR WORKFLOW Work Flow OVERALL SEQUENCE INFOID: A B C D E F G H I J K WW M N O DETAILED FLOW WW-3 JMKIA0101GB

4 < BASIC INSECTI > 1. GET INFORMATI FOR SYMTOM DIAGNOSIS AND REAIR WORKFLOW Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2 2. CHECK DTC 1. Check DTC. 2. erform the following procedure if DTC is displayed. - Record DTC and freeze frame data (rint them out with CSULT-III.) - Erase DTC. - Study the relationship between the cause detected by DTC and the symptom described by the customer. 3. Check related service bulletins for information. Is any symptom described and any DTC detected? Symptom is described, DTC is displayed>>go TO 3 Symptom is described, DTC is not displayed>>go TO 4 Symptom is not described, DTC is displayed>>go TO 5 3. CFIRM THE SYMTOM Confirm the symptom described by the customer. Connect CSULT-III to the vehicle in DATA MITOR mode and check real time diagnosis results. Verify relation between the symptom and the condition when the symptom is detected. >> GO TO 5 4. CFIRM THE SYMTOM Confirm the symptom described by the customer. Connect CSULT-III to the vehicle in DATA MITOR mode and check real time diagnosis results. Verify relation between the symptom and the condition when the symptom is detected. >> GO TO 6 5. ERFORM DTC CFIRMATI ROCEDURE erform DTC Confirmation rocedure for the displayed DTC, and then check that DTC is detected again. At this time, always connect CSULT-III to the vehicle, and check diagnostic results in real time. If two or more DTCs are detected, refer to BCS-79, "DTC Inspection riority Chart" and determine trouble diagnosis order. NOTE: Freeze frame data is useful if the DTC is not detected. erform Component Function Check if DTC Confirmation rocedure is not included in Service Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during this check. If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirmation rocedure. Is DTC detected? YES >> GO TO 8 NO >> Refer to GI-39, "Intermittent Incident". 6. ERFORM BASIC INSECTI erform WW-3, "Work Flow". Inspection End>>GO TO 7 7. DETECT MALFUNCTIING SYSTEM BY SYMTOM TABLE Detect malfunctioning system according to WW-86, "Diagnosis rocedure" based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom. >> GO TO 8 WW-4

5 DIAGNOSIS AND REAIR WORKFLOW < BASIC INSECTI > 8. DETECT MALFUNCTIING ART BY DIAGNOSTIC ROCEDURE Inspect according to Diagnostic rocedure of the system. NOTE: The Diagnostic rocedure described is based on open circuit inspection. A short circuit inspection is also required for the circuit check in the Diagnostic rocedure. Is malfunctioning part detected? YES >> GO TO 9 NO >> Check voltage of related BCM terminals using CSULT-III. 9. REAIR OR RELACE THE MALFUNCTIING ART 1. Repair or replace the malfunctioning part. 2. Reconnect parts or connectors disconnected during Diagnostic rocedure again after repair and replacement. 3. Check DTC. If DTC is displayed, erase it. >> GO TO FINAL CHECK When DTC was detected in step 2, perform DTC Confirmation rocedure or Component Function Check again, and then check that the malfunction has been repaired securely. When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected. Does the symptom reappear? YES (DTC is detected)>>go TO 8 YES (Symptom remains)>>go TO 6 NO >> Inspection End. A B C D E F G H I J K WW M N O WW-5

6 FRT WIER AND WASHER SYSTEM < FUNCTI DIAGNOSIS > FUNCTI DIAGNOSIS FRT WIER AND WASHER SYSTEM System Diagram INFOID: ALCIA0043GB System Description INFOID: OUTLINE The front wiper is controlled by each function of BCM and IDM E/R. Control by BCM Combination switch reading function Front wiper control function Control by IDM E/R Front wiper control function Relay control function FRT WIER BASIC OERATI BCM detects the combination switch condition by the combination switch reading function. BCM transmits the front wiper request signal to IDM E/R with CAN communication depending on each operating condition of the front wiper. IDM E/R turns / the integrated front wiper relay and the front wiper high relay according to the front wiper request signal. IDM E/R provides the power supply to operate the front wiper HI/LO operation. FRT WIER LO OERATI BCM transmits the front wiper request signal (LO) to IDM E/R with CAN communication according to the front wiper LO operating condition. Front wiper LO operating condition - Ignition switch - Front wiper switch LO or front wiper switch MIST (while pressing) IDM E/R turns the integrated front wiper relay according to the front wiper request signal (LO). FRT WIER HI OERATI BCM transmits the front wiper request signal (HI) to IDM E/R with CAN communication according to the front wiper HI operating condition. Front wiper HI operating condition - Ignition switch - Front wiper switch HI IDM E/R turns the integrated front wiper relay and the front wiper high relay according to the front wiper request signal (HI). FRT WIER INT OERATI BCM transmits the front wiper request signal (INT) to IDM E/R with CAN communication depending on the front wiper INT operating condition and intermittent operation delay interval according to the wiper intermittent dial position. Front wiper INT operating condition - Ignition switch - Front wiper switch INT WW-6

7 < FUNCTI DIAGNOSIS > FRT WIER AND WASHER SYSTEM IDM E/R turns the integrated front wiper relay so that the front wiper is operated only once according to the front wiper request signal (INT). BCM detects stop position/except stop position of the front wiper motor according to the front wiper auto stop signal received from IDM E/R with CAN communication. BCM transmits the front wiper request signal (INT) again after the intermittent operation delay interval. A B C D NOTE: Front wiper intermittent operation can be set to the operation with vehicle speed by CSULT-III. Refer to BCS-24, "WIER : CSULT - III Function (BCM-WIER)". Front wiper intermittent operation with vehicle speed BCM calculates the intermittent operation delay interval from the following - Vehicle speed signal (received from the combination meter with CAN communication) - Wiper intermittent dial position Wiper intermittent dial position *: When without vehicle speed setting Intermittent operation interval Vehicle stopped or less than 5 km/h (3.1 MH) Intermittent operation delay Interval (s) 5 km/h (3.1MH) or more or less than 35km/h (21.7 MH) Vehicle speed 35 km/h (21.7 MH) or more or less than 65km/h (40.4 MH)* JLIA0094GB 65 km/h (40.4MH) or more 1 Short Long FRT WIER AUTO STO OERATI BCM stops transmitting the front wiper request signal when the front wiper switch is turned. IDM E/R detects the front wiper auto stop signal from the front wiper motor and detects the front wiper motor position (stop position/except stop position). E F G H I J K WW M N O WW-7

8 FRT WIER AND WASHER SYSTEM < FUNCTI DIAGNOSIS > When the front wiper request signal is stopped, IDM E/R turns the front wiper relay until the front wiper motor returns to the stop position. JLIA0095GB NOTE: BCM stops the transmitting of the front wiper request signal when the ignition switch is. IDM E/R turns the front wiper relay when the ignition switch is. FRT WIER OERATI LINKED WITH WASHER BCM transmits the front wiper request signal (LO) to IDM E/R with CAN communication according to the washer linked operating condition of the front wiper. BCM transmits the front wiper request signal (LO) so that the front wiper operates approximately 2 times when the front washer switch is detected. Washer linked operating condition of front wiper - Ignition switch - Front washer switch (0.4 second or more) IDM E/R turns the integrated front wiper relay according to the front wiper request signal (LO). The front washer motor is grounded through the combination switch when the front washer switch is. FRT WIER FAIL SAFE OERATI When the front wiper auto stop circuit is malfunctioning, IDM E/R performs the fail-safe function. Refer to CS-36, "Fail Safe". WW-8

9 < FUNCTI DIAGNOSIS > Component arts Location FRT WIER AND WASHER SYSTEM INFOID: A B C D E F G H I J K WW M N ALLIA0910ZZ O 1. Front washer motor E226 (view with front bumper cover removed) 2. Combination switch (wiper switch) M28 3. Combination meter M24 4. Front wiper motor E25 5. IDM E/R E17, E18, E BCM M16, M17, M18, M19 (view with instrument panel removed) WW-9

10 FRT WIER AND WASHER SYSTEM < FUNCTI DIAGNOSIS > Component Description INFOID: BCM IDM E/R art Combination switch (Wiper & washer switch) Combination meter Description Judges the switch status by the combination switch reading function. Requests (with CAN communication) the front wiper relay and the front wiper high relay to IDM E/R. Controls the integrated relay according to the request (with CAN communication) from BCM. erforms the auto stop control of the front wiper. Refer to WW-6, "System Description". Transmits the vehicle speed signal to BCM with CAN communication. WW-10

11 < FUNCTI DIAGNOSIS > DIAGNOSIS SYSTEM (BCM) COMM ITEM COMM ITEM : Diagnosis Description DIAGNOSIS SYSTEM (BCM) BCM CSULT-III FUNCTI CSULT-III performs the following functions via CAN communication with BCM. Diagnosis mode WORK SUORT SELF DIAGNOSTIC RESULT CAN DIAG SUORT MNTR DATA MITOR ACTIVE TEST ECU IDENTIFICATI CFIGURATI Changes the setting for each system function. Function Description Displays the diagnosis results judged by BCM. Monitors the reception status of CAN communication viewed from BCM. The BCM input/output signals are displayed. The signals used to activate each device are forcibly supplied from BCM. The BCM part number is displayed. Enables to read and save the vehicle specification. Enables to write the vehicle specification when replacing BCM. INFOID: A B C D E F SYSTEM ALICATI BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the following for all sub system selection items. System Sub system selection item COMM ITEM : CSULT-III Function Diagnosis mode WORK SUORT DATA MITOR ACTIVE TEST Door lock DOOR LOCK Rear window defogger REAR DEFOGGER Warning chime BUZZER Interior room lamp timer INT LAM Exterior lamp HEADLAM Wiper and washer WIER Turn signal and hazard warning lamps FLASHER Intelligent Key system INTELLIGENT KEY Combination switch COMB SW BCM BCM Immobilizer IMMU Interior room lamp battery saver BATTERY SAVER Trunk open TRUNK Vehicle security system THEFT ALM RA system RETAINED WR Signal buffer system SIGNAL BUFFER TMS AIR RESSURE MITOR INFOID: G H I J K WW M N O ECU IDENTIFICATI Displays the BCM part No. SELF-DIAG RESULT Refer to BCS-81, "DTC Index". WIER WW-11

12 < FUNCTI DIAGNOSIS > DIAGNOSIS SYSTEM (BCM) WIER : CSULT - III Function (BCM-WIER) INFOID: WORK SUORT * : Factory setting Service item Setting item Description WIER SEED SET- TING DATA MITOR * With vehicle speed (Front wiper intermittent time linked with the vehicle speed and wiper dial position) Without vehicle speed (Front wiper intermittent time linked with the wiper dial position) USH SW VEH SEED 1 [km/h] FR WIER HI [/] FR WIER LOW [/] FR WASHER SW [/] FR WIER INT [/] FR WIER STO [/] INT VOLUME [1 7] Monitor Item [Unit] Description Displays the status of the engine switch (push switch) judged by BCM. Displays the value of the vehicle speed signal received from combination meter with CAN communication. Status of each switch judged by BCM using the combination switch reading function Displays the status of the front wiper auto stop signal received from IDM E/R with CAN communication. Status of each switch judged by BCM using the combination switch reading function ACTIVE TEST FR WIER Test item Operation Description Hi Lo INT Off Transmits the front wiper request signal (HI) to IDM E/R with CAN communication to operate the front wiper HI operation. Transmits the front wiper request signal (LO) to IDM E/R with CAN communication to operate the front wiper LO operation. Transmits the front wiper request signal (INT) to IDM E/R with CAN communication to operate the front wiper INT operation. Stops transmitting the front wiper request signal to stop the front wiper operation. WW-12

13 < FUNCTI DIAGNOSIS > DIAGNOSIS SYSTEM (IDM E/R) Diagnosis Description DIAGNOSIS SYSTEM (IDM E/R) INFOID: A AUTO ACTIVE TEST Description In auto active test mode, the IDM E/R sends a drive signal to the following systems to check their operation. Oil pressure warning lamp Front wiper (LO, HI) arking lamps License plate lamps Tail lamps Front fog lamps (if equipped) Headlamps (LO, HI) A/C compressor (magnet clutch) Cooling fans Operation rocedure 1. Close the hood and lift the wiper arms from the windshield. (revent windshield damage due to wiper operation) NOTE: When auto active test is performed with hood opened, sprinkle water on windshield beforehand. 2. Turn ignition switch. 3. Turn the ignition switch, and within 20 seconds, press the front door switch LH 10 times. Then turn the ignition switch. CAUTI: Close front door RH. 4. Turn the ignition switch within 10 seconds. After that the horn sounds once and the auto active test starts. 5. The oil pressure warning lamp starts blinking when the auto active test starts. 6. After a series of the following operations is repeated 3 times, auto active test is completed. NOTE: When auto active test mode has to be cancelled halfway through test, turn ignition switch. CAUTI: If auto active test mode cannot be actuated, check door switch system. Refer to DLK-68, "Component Function Check". Do not start the engine. Inspection in Auto Active Test Mode When auto active test mode is actuated, the following 6 steps are repeated 3 times. Operation sequence Inspection Location Operation 1 Oil pressure warning lamp Blinks continuously during operation of auto active test 2 Front wiper LO for 5 seconds HI for 5 seconds 3 arking lamps License plate lamps Tail lamps Front fog lamps (if equipped) 10 seconds 4 Headlamps LO HI 5 times 5 A/C compressor (magnet clutch) 5 times 6 * Cooling fans MID for 5 seconds HI for 5 seconds *: s duty ratio of 50% for 5 seconds duty ratio of 100% for 5 seconds on the cooling fan control module. B C D E F G H I J K WW M N O WW-13

14 < FUNCTI DIAGNOSIS > Concept of auto active test DIAGNOSIS SYSTEM (IDM E/R) ALCIA0032GB IDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communication. Therefore, the CAN communication line between IDM E/R and BCM is considered normal if the auto active test starts successfully. The auto active test facilitates troubleshooting if any systems controlled by IDM E/R cannot be operated. Diagnosis chart in auto active test mode Symptom Inspection contents ossible cause YES BCM signal input circuit Any of the following components do not operate arking lamps License plate lamps Tail lamps Front fog lamps (if equipped) Headlamp (HI, LO) Front wiper erform auto active test. Does the applicable system operate? NO Lamp or motor Lamp or motor ground circuit Harness or connector between IDM E/R and applicable system IDM E/R A/C compressor does not operate erform auto active test. Does the magnet clutch operate? YES Combination meter signal input circuit CAN communication signal between combination meter and ECM CAN communication signal between ECM and IDM E/ R NO Magnet clutch Harness or connector between IDM E/R and magnet clutch IDM E/R WW-14

15 < FUNCTI DIAGNOSIS > DIAGNOSIS SYSTEM (IDM E/R) Oil pressure warning lamp does not operate Cooling fan does not operate CSULT - III Function (IDM E/R) ALICATI ITEM CSULT-III performs the following functions via CAN communication with IDM E/R. ECU Identification Diagnosis mode Self Diagnostic Result Data Monitor Active Test CAN Diag Support Monitor SELF DIAGNOSTIC Refer to CS-38, "DTC Index". DATA MITOR Monitor item Monitor Item [Unit] MOTOR FAN REQ [1,2,3,4] AC COM REQ [Off/On] TAIL&CLR REQ [Off/On] HL LO REQ [Off/On] HL HI REQ [Off/On] Symptom Inspection contents ossible cause erform auto active test. Does the oil pressure warning lamp blink? erform auto active test. Does the cooling fan operate? Description Allows confirmation of IDM E/R part number. Displays the diagnosis results judged by IDM E/R. YES NO YES Displays the real-time input/output data from IDM E/R input/output data. NO Harness or connector between IDM E/R and oil pressure switch Oil pressure switch IDM E/R CAN communication signal between IDM E/R and BCM CAN communication signal between BCM and combination meter Combination meter ECM signal input circuit CAN communication signal between ECM and IDM E/ R Cooling fan Harness or connector between cooling fan and cooling fan relays Cooling fan relays Harness or connector between IDM E/R and cooling fan relays IDM E/R INFOID: IDM E/R can provide a drive signal to electronic components to check their operations. The results of transmit/receive diagnosis of CAN communication can be read. MAIN SIG- NALS Description Displays the value of the cooling fan speed signal received from ECM via CAN communication. Displays the status of the A/C compressor request signal received from ECM via CAN communication. Displays the status of the position light request signal received from BCM via CAN communication. Displays the status of the low beam request signal received from BCM via CAN communication. Displays the status of the high beam request signal received from BCM via CAN communication. A B C D E F G H I J K WW M N O WW-15

16 < FUNCTI DIAGNOSIS > FR FOG REQ [Off/On] FR WI REQ [Stop/1LOW/Low/Hi] WI AUTO STO [STO /ACT ] WI ROT [Off/BLOCK] IGN RLY1 -REQ [Off/On] IGN RLY [Off/On] USH SW [Off/On] INTER/N SW [Off/On] ST RLY CT [Off/On] IHBT RLY -REQ [Off/On] ST/INHI RLY [Off/ ST /INHI] DETENT SW [Off/On] S/L RLY -REQ 1 [Off/On] S/L STATE 1 [LOCK/UNLK/UNKWN] DTRL REQ [Off] OIL SW [Open/Close] THFT HRN REQ [Off/On] HORN CHIR [Off/On] Monitor Item [Unit] DIAGNOSIS SYSTEM (IDM E/R) MAIN SIG- NALS Description Displays the status of the front fog light request signal received from BCM via CAN communication. Displays the status of the front wiper request signal received from BCM via CAN communication. Displays the status of the front wiper auto stop signal judged by IDM E/R. Displays the status of the front wiper fail-safe operation judged by IDM E/R. Displays the status of the ignition switch signal received from BCM via CAN communication. Displays the status of the ignition relay judged by IDM E/R. Displays the status of the push-button ignition switch judged by IDM E/R. Displays the status of the CVT shift position judged by IDM E/R. Displays the status of the starter relay status signal received from BCM via CAN communication. Displays the status of the starter control relay signal received from BCM via CAN communication. Displays the status of the starter relay and starter control relay judged by IDM E/R. Displays the status of the CVT shift selector (detention switch) judged by IDM E/ R. Displays the status of the steering lock relay request received from BCM via CAN communication. Displays the status of the electronic steering column lock judged by IDM E/R. Displays the status of the daytime light request signal received from BCM via CAN communication. Displays the status of the oil pressure switch judged by IDM E/R. Displays the status of the theft warning horn request signal received from BCM via CAN communication. Displays the status of the horn reminder signal received from BCM via CAN communication. 1: Early production ACTIVE TEST Test item Test item Operation Description HORN On Operates horn relay 1 and horn relay 2 for 20 ms. FRT WIER MOTOR FAN Off Lo Hi 1 Operates the front wiper relay. Operates the front wiper relay and front wiper high relay. 2 s 50% pulse duty signal (WM signal) to the cooling fan control module. 3 s 80% pulse duty signal (WM signal) to the cooling fan control module. 4 s 100% pulse duty signal (WM signal) to the cooling fan control module. WW-16

17 < FUNCTI DIAGNOSIS > DIAGNOSIS SYSTEM (IDM E/R) Test item Operation Description EXTERNAL LAMS Off TAIL Lo Hi Fog Operates the tail lamp relay. Operates the headlamp low relay. Operates the headlamp low relay and / the headlamp high relay at 1 second intervals. Operates the front fog lamp relay. A B C D E F G H I J K WW M N O WW-17

18 < COMENT DIAGNOSIS > COMENT DIAGNOSIS WIER AND WASHER FUSE Description WIER AND WASHER FUSE INFOID: Fuse list Unit Location Fuse No. Capacity Front wiper motor IDM E/R A Front washer motor IDM E/R A Diagnosis rocedure 1. CHECK FUSES Check that the following fuses are not blown. INFOID: Unit Location Fuse No. Capacity Front wiper motor IDM E/R A Front washer motor IDM E/R A Is the fuse blown? YES >> Replace the blown fuse after repairing the affected circuit. NO >> The fuse is normal. WW-18

19 < COMENT DIAGNOSIS > FRT WIER MOTOR LO CIRCUIT FRT WIER MOTOR LO CIRCUIT Component Function Check 1. CHECK FRT WIER LO OERATI IDM E/R AUTO ACTIVE TEST 1. Start IDM E/R auto active test. Refer to CS-14, "Diagnosis Description". 2. Check that the front wiper operates at the LO operation. CSULT-III ACTIVE TEST 1. Select "FRT WIER" of IDM E/R active test item. 2. While operating the test item, check front wiper LO operation and. LO Does the front wiper operate? YES >> Front wiper motor LO circuit is normal. NO >> Refer to WW-19, "Diagnosis rocedure". Diagnosis rocedure : Front wiper LO operation : Stop the front wiper. Regarding Wiring Diagram information, refer to WW-26, "Wiring Diagram". 1. CHECK FRT WIER MOTOR (LO) OUTUT VOLTAGE CSULT-III ACTIVE TEST 1. Turn the ignition switch. 2. Disconnect front wiper motor. 3. Turn the ignition switch. 4. Select "FRT WIER" of IDM E/R active test item. 5. While operating the test item, check voltage between IDM E/R harness connector and ground. Terminals Test item (+) (-) Voltage (V) (Approx.) IDM E/R FRT WIER Connector Terminal LO E18 4 Is the measurement normal? YES >> GO TO 2 NO >> Replace IDM E/R. Refer to CS-41, "Removal and Installation". 2. CHECK FRT WIER MOTOR (LO) OEN CIRCUIT INFOID: INFOID: ALLIA0922ZZ A B C D E F G H I J K WW M N O WW-19

20 FRT WIER MOTOR LO CIRCUIT < COMENT DIAGNOSIS > 1. Turn the ignition switch. 2. Disconnect IDM E/R. 3. Check continuity between IDM E/R harness connector (A) and front wiper motor harness connector (B). IDM E/R Front wiper motor Connector Terminal Connector Terminal Continuity E18 (A) 4 E25 (B) 1 Yes Does continuity exist? YES >> GO TO 3 NO >> Repair or replace harness. 3. CHECK FRT WIER MOTOR (LO) SHORT CIRCUIT Check continuity between IDM E/R harness connector and ground. ALLIA0816ZZ Connector IDM E/R Terminal Continuity E18 4 No Does continuity exist? YES >> Repair or replace harness. NO >> Replace front wiper motor. Refer to WW-96, "FRT WIER DRIVE ASSEMBLY : Removal and Installation". ALLIA0208ZZ WW-20

21 < COMENT DIAGNOSIS > FRT WIER MOTOR HI CIRCUIT Component Function Check 1. CHECK FRT WIER HI OERATI FRT WIER MOTOR HI CIRCUIT IDM E/R AUTO ACTIVE TEST 1. Start IDM E/R auto active test. Refer to CS-14, "Diagnosis Description". 2. Check that the front wiper operates at the HI operation. CSULT-III ACTIVE TEST 1. Select "FRT WIER" of IDM E/R active test item. 2. While operating the test item, check front wiper HI operation and. HI Does the front wiper operate? YES >> The front wiper motor HI circuit is normal. NO >> Refer to WW-21, "Diagnosis rocedure". Diagnosis rocedure : Front wiper HI operation : Stop the front wiper. Regarding Wiring Diagram information, refer to WW-26, "Wiring Diagram". 1. CHECK FRT WIER MOTOR (HI) OUTUT VOLTAGE CSULT-III ACTIVE TEST 1. Turn the ignition switch. 2. Disconnect front wiper motor. 3. Turn the ignition switch. 4. Select "FRT WIER" of IDM E/R active test item. 5. While operating the test item, check voltage between IDM E/R harness connector and ground. Terminals Test item (+) (-) Voltage (V) IDM E/R (Approx.) FRT WIER Connector Terminal HI E18 5 Is the measurement normal? YES >> GO TO 2 NO >> Replace IDM E/R. Refer to CS-41, "Removal and Installation". 2. CHECK FRT WIER MOTOR (HI) OEN CIRCUIT INFOID: INFOID: ALLIA0209ZZ A B C D E F G H I J K WW M N O WW-21

22 FRT WIER MOTOR HI CIRCUIT < COMENT DIAGNOSIS > 1. Turn the ignition switch. 2. Disconnect IDM E/R. 3. Check continuity between IDM E/R harness connector (A) and front wiper motor harness connector (B). IDM E/R Front wiper motor Connector Terminal Connector Terminal Continuity E18 (A) 5 E25 (B) 4 Yes Does continuity exist? YES >> GO TO 3 NO >> Repair or replace harness. 3. CHECK FRT WIER MOTOR (HI) SHORT CIRCUIT Check continuity between IDM E/R harness connector and ground. ALLIA0817ZZ Connector IDM E/R Terminal Continuity E18 5 No Does continuity exist? YES >> Repair or replace harness. NO >> Replace front wiper motor. Refer to WW-96, "FRT WIER DRIVE ASSEMBLY : Removal and Installation". ALLIA0211ZZ WW-22

23 < COMENT DIAGNOSIS > FRT WIER AUTO STO SIGNAL CIRCUIT FRT WIER AUTO STO SIGNAL CIRCUIT Component Function Check 1. CHECK FRT WIER (AUTO STO) OERATI CSULT-III DATA MITOR 1. Select "WI AUTO STO" of IDM E/R DATA MITOR item. 2. Operate the front wiper. 3. With the front wiper operation, check the monitor status. Monitor item Condition Monitor status Stop position WI AUTO STO Front wiper motor Except Is the status of item normal? YES >> Auto stop signal circuit is normal. NO >> Refer to WW-23, "Diagnosis rocedure". Diagnosis rocedure Regarding Wiring Diagram information, refer to WW-26, "Wiring Diagram". 1. CHECK FRT WIER MOTOR (AUTO STO) OUTUT VOLTAGE 1. Turn the ignition switch. 2. Disconnect front wiper motor. 3. Turn the ignition switch. 4. Check voltage between IDM E/R harness connector and ground. Connector Terminals (+) (-) IDM E/R Terminal Voltage (V) (Approx.) STO ACT E18 16 Is the measurement normal? YES >> GO TO 2 NO >> Replace IDM E/R. Refer to CS-41, "Removal and Installation". 2. CHECK FRT WIER MOTOR (AUTO STO) CIRCUIT CTINUITY 1. Turn the ignition switch. 2. Disconnect IDM E/R. 3. Check continuity between IDM E/R harness connector (A) and front wiper motor harness connector (B). INFOID: INFOID: ALLIA0212ZZ A B C D E F G H I J K WW M N O IDM E/R Front wiper motor Connector Terminal Connector Terminal Continuity E18 (A) 16 E25 (B) 5 Yes Does continuity exist? YES >> GO TO 3 NO >> Repair or replace harness. 3. CHECK FRT WIER MOTOR (AUTO STO) SHORT CIRCUIT ALLIA0818ZZ WW-23

24 FRT WIER AUTO STO SIGNAL CIRCUIT < COMENT DIAGNOSIS > Check continuity between IDM E/R harness connector and ground. Connector IDM E/R Terminal Continuity E18 16 No Does continuity exist? YES >> Repair or replace harness. NO >> Replace front wiper motor. Refer to WW-96, "FRT WIER DRIVE ASSEMBLY : Removal and Installation". ALLIA0214ZZ WW-24

25 < COMENT DIAGNOSIS > FRT WIER MOTOR GROUND CIRCUIT FRT WIER MOTOR GROUND CIRCUIT Diagnosis rocedure Regarding Wiring Diagram information, refer to WW-26, "Wiring Diagram". 1.CHECK FRT WIER MOTOR (GND) OEN CIRCUIT 1. Turn the ignition switch. 2. Disconnect front wiper motor. 3. Check continuity between front wiper motor harness connector and ground. Connector Front wiper motor Terminal Continuity E25 2 Yes Does continuity exist? YES >> Front wiper motor ground circuit is normal. NO >> Repair or replace harness. INFOID: ALLIA0819ZZ A B C D E F G H I J K WW M N O WW-25

26 FRT WIER AND WASHER SYSTEM < COMENT DIAGNOSIS > FRT WIER AND WASHER SYSTEM Wiring Diagram INFOID: ABLWA0570GB WW-26

27 < COMENT DIAGNOSIS > FRT WIER AND WASHER SYSTEM A B C D E F G H I J K WW M N O ABLIA1209GB WW-27

28 FRT WIER AND WASHER SYSTEM < COMENT DIAGNOSIS > ABLIA1702GB WW-28

29 < COMENT DIAGNOSIS > FRT WIER AND WASHER SYSTEM A B C D E F G H I J K WW M N O ABLIA1703GB WW-29

30 FRT WIER AND WASHER SYSTEM < COMENT DIAGNOSIS > ABLIA1704GB WW-30

31 < ECU DIAGNOSIS > ECU DIAGNOSIS BCM (BODY CTROL MODULE) Reference Value BCM (BODY CTROL MODULE) INFOID: A B VALUES THE DIAGNOSIS TOOL Monitor Item Condition Value/Status FR WIER HI Other than front wiper switch HI Front wiper switch HI FR WIER LOW Other than front wiper switch LO Front wiper switch LO FR WASHER SW Front washer switch Front washer switch FR WIER INT Other than front wiper switch INT Front wiper switch INT FR WIER STO Front wiper is not in STO position Front wiper is in STO position INT VOLUME Wiper intermittent dial is in a dial position 1-7 Wiper intermittent dial position TURN SIGNAL R TURN SIGNAL L TAIL LAM SW HI BEAM SW HEAD LAM SW 1 HEAD LAM SW 2 ASSING SW AUTO LIGHT SW FR FOG SW DOOR SW-DR DOOR SW-AS DOOR SW-RR DOOR SW-RL Other than turn signal switch RH Turn signal switch RH Other than turn signal switch LH Turn signal switch LH Other than lighting switch 1ST and 2ND Lighting switch 1ST or 2ND Other than lighting switch HI Lighting switch HI Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch 2ND Lighting switch 2ND Other than lighting switch ASS Lighting switch ASS Other than lighting switch AUTO Lighting switch AUTO Front fog lamp switch Front fog lamp switch Driver door closed Driver door opened assenger door closed assenger door opened Rear door RH closed Rear door RH opened Rear door LH closed Rear door LH opened C D E F G H I J K WW M N O WW-31

32 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) CDL LOCK SW CDL UNLOCK SW KEY CYL LK-SW KEY CYL UN-SW HAZARD SW Other than power door lock switch LOCK ower door lock switch LOCK Other than power door lock switch UNLOCK ower door lock switch UNLOCK Other than driver door key cylinder LOCK position Driver door key cylinder LOCK position Other than driver door key cylinder UNLOCK position Driver door key cylinder UNLOCK position When hazard switch is not pressed When hazard switch is pressed REAR DEF SW When rear window defogger switch is pressed TR CANCEL SW TR/BD OEN SW TRNK/HAT MNTR RKE-LOCK RKE-UNLOCK RKE-TR/BD RKE-ANIC RKE-/W OEN RKE-MODE CHG OTICAL SENSOR REQ SW-DR REQ SW-AS REQ SW-RL REQ SW-RR REQ SW-BD/TR USH SW Monitor Item Condition Value/Status Trunk lid opener cancel switch Trunk lid opener cancel switch Trunk lid opener switch While the trunk lid opener switch is turned Trunk lid closed Trunk lid opened When LOCK button of Intelligent Key is not pressed When LOCK button of Intelligent Key is pressed When UNLOCK button of Intelligent Key is not pressed When UNLOCK button of Intelligent Key is pressed When TRUNK OEN button of Intelligent Key is not pressed When TRUNK OEN button of Intelligent Key is pressed When ANIC button of Intelligent Key is not pressed When ANIC button of Intelligent Key is pressed When UNLOCK button of Intelligent Key is not pressed and held When UNLOCK button of Intelligent Key is pressed and held When LOCK/UNLOCK button of Intelligent Key is not pressed and held simultaneously When LOCK/UNLOCK button of Intelligent Key is pressed and held simultaneously When outside of the vehicle is bright When outside of the vehicle is dark When front door request switch is not pressed (driver side) When front door request switch is pressed (driver side) When front door request switch is not pressed (passenger side) When front door request switch is pressed (passenger side) When rear door request switch is not pressed (driver side) When rear door request switch is pressed (driver side) When rear door request switch is not pressed (passenger side) When rear door request switch is pressed (passenger side) When trunk request switch is not pressed When trunk request switch is pressed When engine switch (push switch) is not pressed When engine switch (push switch) is pressed Close to 5 V Close to 0 V WW-32

33 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) IGN RLY 2-F/B ACC RLY-F/B BRAKE SW 1 DETE/CANCL SW SFT N/N SW Ignition switch or ACC Ignition switch Ignition switch Ignition switch ACC or When the brake pedal is not depressed When the brake pedal is depressed When selector lever is in position When selector lever is in any position other than When selector lever is in any position other than or N When selector lever is in or N position Electronic steering column lock LOCK status S/L-LOCK * Electronic steering column lock UNLOCK status Electronic steering column lock UNLOCK status S/L-UNLOCK * Electronic steering column lock LOCK status Ignition switch or ACC S/L RELAY-F/B * Ignition switch UNLK SEN-DR USH SW-IDM IGN RLY1 F/B DETE SW -IDM SFT N -IDM SFT -MET SFT N-MET Monitor Item Condition Value/Status ENGINE STATE Driver door UNLOCK status Driver door LOCK status When engine switch (push switch) is not pressed When engine switch (push switch) is pressed Ignition switch or ACC Ignition switch When selector lever is in position When selector lever is in any position other than When selector lever is in any position other than or N When selector lever is in or N position When selector lever is in any position other than When selector lever is in position When selector lever is in any position other than N When selector lever is in N position Engine stopped While the engine stalls At engine cranking Engine running Electronic steering column lock LOCK status S/L LOCK-IDM * Electronic steering column lock UNLOCK status Electronic steering column lock UNLOCK status S/L UNLK-IDM * Electronic steering column lock LOCK status Ignition switch or ACC S/L RELAY-REQ * Ignition switch STO STALL CRANK VEH SEED 1 While driving Equivalent to speedometer reading VEH SEED 2 While driving Equivalent to speedometer reading RUN A B C D E F G H I J K WW M N O WW-33

34 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) DOOR STAT-DR DOOR STAT-AS ID OK FLAG RMT ENG STRT KEY SW -SLOT Driver door LOCK status Wait with selective UNLOCK operation (5 seconds) Driver door UNLOCK status assenger door LOCK status Wait with selective UNLOCK operation (5 seconds) assenger door UNLOCK status Ignition switch ACC or Ignition switch When the engine start is prohibited When the engine start is permitted When Intelligent Key is not inserted into key slot When Intelligent Key is inserted into key slot LOCK READY UNLK LOCK READY UNLK RESET SET RESET RKE OE COUN1 During the operation of Intelligent Key Operation frequency of Intelligent Key CFRM ID ALL CFIRM ID4 CFIRM ID3 CFIRM ID2 CFIRM ID1 T 4 T 3 T 2 T 1 Monitor Item Condition Value/Status AIR RESS FL AIR RESS FR AIR RESS RR AIR RESS RL The key ID that the key slot receives does not accord with any key ID registered to BCM. The key ID that the key slot receives accords with any key ID registered to BCM. The key ID that the key slot receives does not accord with the fourth key ID registered to BCM. The key ID that the key slot receives accords with the fourth key ID registered to BCM. The key ID that the key slot receives does not accord with the third key ID registered to BCM. The key ID that the key slot receives accords with the third key ID registered to BCM. The key ID that the key slot receives does not accord with the second key ID registered to BCM. The key ID that the key slot receives accords with the second key ID registered to BCM. The key ID that the key slot receives does not accord with the first key ID registered to BCM. The key ID that the key slot receives accords with the first key ID registered to BCM. The ID of fourth key is not registered to BCM The ID of fourth key is registered to BCM The ID of third key is not registered to BCM The ID of third key is registered to BCM The ID of second key is not registered to BCM The ID of second key is registered to BCM The ID of first key is not registered to BCM The ID of first key is registered to BCM Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) Ignition switch (only when the signal from the transmitter is received) SET YET DE YET DE YET DE YET DE YET DE YET DE YET DE YET DE YET DE Air pressure of front LH tire Air pressure of front RH tire Air pressure of rear RH tire Air pressure of rear LH tire WW-34

35 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Monitor Item Condition Value/Status ID REGST FL1 When ID of front LH tire transmitter is registered DE When ID of front LH tire transmitter is not registered YET ID REGST FR1 When ID of front RH tire transmitter is registered DE When ID of front RH tire transmitter is not registered YET ID REGST RR1 When ID of rear RH tire transmitter is registered DE When ID of rear RH tire transmitter is not registered YET ID REGST RL1 When ID of rear LH tire transmitter is registered DE When ID of rear LH tire transmitter is not registered YET WARNING LAM Tire pressure indicator Tire pressure indicator BUZZER Tire pressure warning alarm is not sounding Tire pressure warning alarm is sounding * : With electronic steering column lock A B C D E F G H I J K WW M N O WW-35

36 < ECU DIAGNOSIS > Terminal Layout BCM (BODY CTROL MODULE) INFOID: hysical Values ALMIA0127ZZ INFOID: WW-36

37 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) 1 (W/B) 2 (R/Y) 3 (L/W) 4 (/W) 5 (G) 7 (R/W) 8 (V) 9 (L) 10 (G) 11 (Y/R) 13 (B) 14 (GR/ W) Description Signal name Input/ Condition Battery power supply Input Ignition switch Battery power supply output Ignition power supply output Interior room lamp power supply Front door RH UN- LOCK Ignition switch Ignition switch After passing the interior room lamp battery saver operation time Any other time after passing the interior room lamp battery saver operation time Front door RH Step lamp Step lamp All doors LOCK All doors Front door LH UN- LOCK Rear door RH and rear door LH UN- LOCK Front door LH Rear door RH and rear door LH UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) LOCK (actuator is activated) Other than LOCK (actuator is not activated) UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) UNLOCK (actuator is activated) Other than UNLOCK (actuator is not activated) Battery power supply Input Ignition switch Ignition switch Engine switch (push switch) illumination ground Input Tail lamp Value (Approx.) NOTE: When the illumination brightening/dimming level is in the neutral position A B C D E F G H I J K WW M N O 15 (Y/L) ACC indicator lamp Ignition switch ACC or JSNIA0010GB WW-37

38 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) Turn signal switch 17 (G/B) Turn signal (RH) Ignition switch Turn signal switch RH 6.5 V KID0926E Turn signal switch 18 (G/Y) Turn signal (LH) Ignition switch Turn signal switch LH 19 (Y) 21 (/B) 24 (R/W) 26 (O/L) Room lamp timer control Optical sensor signal Input Interior room lamp Ignition switch When outside of the vehicle is bright When outside of the vehicle is dark Close to 5V Close to Stop lamp switch 1 Input Stop lamp switch 2 Input Stop lamp switch (brake pedal is released) (brake pedal is depressed) 6.5 V KID0926E 27 (O) Front door lock assembly LH (unlock sensor) Input Front door LH LOCK status 29 (Y) 30 (V/Y) 31 (G) UNLOCK status When Intelligent Key is inserted into key slot Key slot switch Input When Intelligent Key is not inserted into key slot 0 ACC feedback signal Input Ignition switch ACC or Rear window defogger feedback signal Input Rear window defogger switch 11.8V JMIA0011GB WW-38

39 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B 32 (R/B) Front door RH switch Input Front door RH switch (when front door RH closes) C 11.8 V JMIA0011GB D (when front door RH opens) E 37 (O) Trunk lid opener cancel switch Input Trunk lid opener cancel switch CANCEL F 1.1V JMIA0012GB G 38 (GR/ W) Rear window defogger signal Input Rear window defogger switch 5V H I 40 (Y/G) ower window serial link Input/ Ignition switch J 10.2V JMIA0013GB K 41 (W) 42 (R) 45 () Engine switch (push switch) illumination LOCK indicator lamp Receiver & sensor ground Ignition switch or ACC Engine switch (push switch) illumination LOCK indicator lamp 5.5V Input Ignition switch WW M N 46 (V/W) Receiver & sensor power supply output Ignition switch ACC or 5. O WW-39

40 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) Standby state OCC3881D 47 1 (G/O) Tire pressure receiver signal Input/ Ignition switch When receiving the signal from the transmitter OCC3880D 48 (R/G) Selector lever transmission range switch signal Input Selector lever or N position 12. Except and N positions 49 (L/O) Security indicator signal Security indicator Blinking 11.3V JMIA0014GB All switch Lighting switch 1ST 50 (LG/ B) Combination switch OUTUT 5 Combination switch (Wiper intermittent dial 4) Lighting switch high-beam Lighting switch 2ND Turn signal switch RH 10.7V JMIA0031GB All switch (Wiper intermittent dial 4) Front wiper switch HI (Wiper intermittent dial 4) 51 (L/W) Combination switch OUTUT 1 Combination switch Any of the conditions below with all switch Wiper intermittent dial 1 WIper intermittent dial 2 Wiper intermittent dial 3 Wiper intermittent dial 6 Wiper intermittent dial V JMIA0032GB WW-40

41 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A All switch (Wiper intermittent dial 4) B 52 (G/B) Combination switch OUTUT 2 Combination switch Front washer switch (Wiper intermittent dial 4) Any of the conditions below with all switch Wiper intermittent dial 1 WIper intermittent dial 5 Wiper intermittent dial 6 All switch 10.7V JMIA0033GB C D E Front wiper switch INT 53 (LG/ R) Combination switch OUTUT 3 Combination switch (Wiper intermittent dial 4) Front wiper switch LO Lighting switch AUTO F G All switch 10.7V JMIA0034GB H Front fog lamp switch 54 (G/Y) Combination switch OUTUT 4 Combination switch (Wiper intermittent dial 4) Lighting switch 2ND Lighting switch flash-topass I J 57 1 (W) Tire pressure warning check switch Turn signal switch LH Input 5V 10.7V JMIA0035GB K WW 58 (SB) Front door LH switch Input Front door LH switch (front door LH CLOSE) M 11.8V JMIA0011GB N (front door LH OEN) 59 (G/R) Rear window defogger relay Rear window defogger Active Not activated O WW-41

42 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) When Intelligent Key is in the passenger compartment JMKIA0062GB 60 (B/R) Front console antenna 2 (-) Ignition switch When Intelligent Key is not in the passenger compartment JMKIA0063GB When Intelligent Key is in the passenger compartment JMKIA0062GB 61 (W/R) Center console antenna 2 (+) Ignition switch When Intelligent Key is not in the passenger compartment JMKIA0063GB When Intelligent Key is in the antenna detection area 62 (V) Front outside handle RH antenna (-) When the front door RH request switch is operated with ignition switch JMKIA0062GB When Intelligent Key is not in the antenna detection area JMKIA0063GB WW-42

43 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B When Intelligent Key is in the antenna detection area C 63 () Front outside handle RH antenna (+) When the front door RH request switch is operated with ignition switch When Intelligent Key is not in the antenna detection area JMKIA0062GB D E F JMKIA0063GB G When Intelligent Key is in the antenna detection area H 64 (V) Front outside handle LH antenna (-) When the front door LH request switch is operated with ignition switch JMKIA0062GB I J When Intelligent Key is not in the antenna detection area K JMKIA0063GB WW M When Intelligent Key is in the antenna detection area N 65 () Front outside handle LH antenna (+) When the front door LH request switch is operated with ignition switch JMKIA0062GB O When Intelligent Key is not in the antenna detection area JMKIA0063GB WW-43

44 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) 68 (G/O) NATS antenna amp (built in key slot) Input/ During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. ointer of tester should move. 69 (O) NATS antenna amp (built in key slot) Input/ During waiting Ignition switch is pressed while inserting the Intelligent Key into the key slot. Just after pressing ignition switch. ointer of tester should move. 70 (R/B) Ignition relay-2 control Ignition switch or ACC During waiting JMKIA0064GB 71 (L/O) Remote keyless entry receiver signal Input/ When operating either button on Intelligent Key JMKIA0065GB All switch (Wiper intermittent dial 4) 1.4V JMIA0041GB 75 (R/Y) Combination switch INUT 5 Input Combination switch Front fog lamp switch (Wiper intermittent dial 4) 1.3V JMIA0037GB Any of the conditions below with all switch Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 6 Wiper intermittent dial 7 1.3V JMIA0040GB WW-44

45 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) Description Signal name Input/ Condition Value (Approx.) A B All switch (Wiper intermittent dial 4) C 1.4V JMIA0041GB D E Lighting switch high-beam (Wiper intermittent dial 4) F 76 (R/G) Combination switch INUT 3 Input Combination switch 1.3V JMIA0036GB G Lighting switch 2ND (Wiper intermittent dial 4) H 1.3V JMIA0037GB I J Any of the conditions below with all switch Wiper intermittent dial 1 Wiper intermittent dial 2 Wiper intermittent dial 3 K 1.3V JMIA0040GB WW 77 2 (BR) 78 () Engine switch (push switch) CAN-L Input Input/ Engine switch (push switch) ressed Not pressed M 79 (L) CAN-H Input/ N O 80 (R/L) Key slot illumination Key slot illumination Blinking 6.5V JMIA0015GB WW-45

46 < ECU DIAGNOSIS > BCM (BODY CTROL MODULE) Terminal No. (Wire color) (+) (-) 81 (LG) 83 (L) 84 (Y/R) 85 3 (L/O) 86 3 (G/R) 87 (G/B) indicator lamp Ignition switch ACC relay control Ignition switch or ACC ACC or CVT shift selector Description Signal name Electronic steering column lock condition No. 1 Electronic steering column lock condition No. 2 Selector lever position switch Input/ Input Input Input Electronic steering column lock Electronic steering column lock Selector lever Condition Lock status Unlock status Lock status Unlock status position Any position other than (pressed) Value (Approx.) 88 (R) Front door RH request switch Input Front door RH request switch (not pressed) 1. JMIA0016GB (pressed) 89 (R) Front door LH request switch Input Front door LH request switch (not pressed) 1. JMIA0016GB 90 (Y) Blower fan motor relay control Ignition switch or ACC 91 (L/R) Remote keyless entry receiver power supply Ignition switch 94 3 (G/Y) Steering wheel lock unit power supply Ignition switch or ACC WW-46