CBI Hydraulic Magnetic Circuit Breakers

Transcription

1 CBI Hydraulic Magnetic Circuit Breakers

2 DATA SHEET Contents CBI Ranges of Circuit Breakers 3 Principle of the Hydraulic Magnetic Circuit Breakers 4 B-Frame Series Circuit breakers 8 C-Frame Series Circuit breakers D-Frame Series Circuit breakers Q-Series Earth Leakage Protection Products 4 Q-Series Miniature Circuit breakers 8 Q-series Surge Protection Devices

3 DATA SHEET CBE Range Principle of the Hydraulic Magnetic Breakers Armature Trip Latch Trip Trip Pole Oil Core Spring Tube Coil Frame 3 4 Hydraulic Magnetic Circuit Breakers (HMCB) operate on the magnetic force produced by a load current flowing through a series connected solenoid coil which is wound around an hermetically sealed tube containing an iron core, a spring and dampening fluid. At currents below the circuit breaker rating, the magnetic flux in the solenoid is insufficient to attract the core towards the pole piece due to the spring pressure. Where anoverload occurs, i.e. currents above the circuit breaker rating, the magnetic flux in the solenoid produces sufficient pull on the core to commenceits movement toward the pole piece. During this movement, the hydraulic fluid regulates the cores speed of travel, thereby creating a controlled time delay which is inversely proportional to the magnitude of the current. This time delay is useful in that if the overload is of short duration, i.e. start up of motors, etc, the core returns to its rest position once the overload disappears. QUALITY TQ EC H N OLO GY If the overload persists, the core reaches the pole piece after a time delay particular to that current and in so doing, the reluctance of the magnetic circuit drops considerably, so that the armature is attracted to the pole face with sufficient force to collapse the latch mechanism (toggle) and consequently trip the breaker. The contacts separate, the current ceases to flow, and the core returns to its rest position. With high values of overloads or short circuit, the magnetic flux produced by the coil is sufficient to attract the armature to the pole face and trip the breaker even though the core has not moved. This is called the instantaneous trip region of the circuit breaker characteristic. Unlike thermal circuit breakers, the hydraulic magnetic circuit breaker s trip point is unaffected by ambient temperature. After tripping, the breaker may be re-closed immediately since there is no cooling down time necessary. By the nature of theprinciple of operation, it is possible to obtain any variation of time/current characteristic. Features - Circuit breakers can carry 00% of rated current independent of ambient temperature. - Trip point not affected by ambient temperature suitable for mounting into small enclosures. - Immediate resetting after trip. - Any current rating possible. - Large range of time delays available. 3

4 4

5 5

6 For Options not listed please contact Emcomp for assistance 6

7 7

8 DATA SHEET CBE Range C-Frame Series Circuit Breakers Features - Hydraulic-Magnetic Technology - 00% Rating Capability Independent of Ambient Temperature - Up to Six Poles - culus, curus, VDE and CE Approved - Optional Trip Alarm and Auxiliary Switch - Optional Mid Trip Indication - Wide Range of Circuits, Mountings,Terminations and Time Delays Available - Two Colour Handle Indication (Two Tone Flush Rocker) - Motor Starting Applications to 30A Applications - Telecoms DC Power Distribution - UPS Equipment - Mobile Power-Generation Equipment - Power Conditioning Equipment - Alternative Energy Equipment - Lighting Control - Marine Protection Technical Data Product Type Approvals Number of Poles Operating Voltages Current Ratings Interrupting capacity Circuit Breaker culus 489 (), 0 V AC, 0/40V AC A 5kA Circuit Breaker UL489A, 80V DC A 5kA Circuit Breaker curus (), CE,VDE (EN60934), 80V DC A 7.5kA curus / 4kA VDE Circuit Breaker curus (), CE,VDE (EN60934) 6 curus / 4 VDE 40V AC A ka & 5kA (3) Product Type Circuit Breaker Circuit Breaker Circuit Breaker Circuit Breaker Approvals Number of Poles Operating Voltages Current Ratings Interrupting capacity Vibration Resistance Shock Resistance Operating Temperature Range Notes: Preferred Standard Delays TRIP TIME IN SECONDS curus () 77V AC A ka & 5kA (3) curus (), UL500 65V DC A.5kA curus (), UL500, 0V AC, 0/40V AC A.5kA curus (4) 3 80V DC, 40V AC, 77V AC A 0G to MIL-STD-0F Method 04D Test A 00G to MIL-STD-0F Method 3B Test A -40 O C to +85 O C () () (3) (4) UL489 & CSA. No 5-0, UL077 & CSA. No 35-M89, 5kA with back up fuse, UL508 & CSA. No 4-M9 50/60Hz DC } LONG DELAY CODE: AS TYPICAL TIME/CURRENT CHARACTERISTICS AT 5 C TRIP TIME IN SECONDS /60Hz DC } LONG DELAY CODE: BS TYPICAL TIME/CURRENT CHARACTERISTICS AT 5 C PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT /60Hz DC } LONG DELAY CODE: CS /60Hz DC } LONG DELAY CODE: OP TRIP TIME IN SECONDS TYPICAL TIME/CURRENT CHARACTERISTICS AT 5 C TRIP TIME IN SECONDS TYPICAL TIME/CURRENT CHARACTERISTICS AT 5 C PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT 8

9 DATA SHEET CBE Range C-Frame Series Circuit Breakers Long Group 0: Frame Group : Type Group : Mounting Group 3: Handle or Pole Blank (Reduced Handle) Group 4: Main Terminal Group 5: Number of Poles Group 6: Rated Voltage and Frequency Group 7: Time Delay (For details of time delay refer to the application guide or web site) Group 8: Main Circuit Current (Example only, any ampere rating possible) Group 9: Circuit Configuration C C-Frame A C-Frame CR UL Recognized VDE (60934) approvals only B C-Frame Mark IV G C-Frame Mark IV UL 500 UL Recognized approvals only 3 Snap-in mount edges beveled See figure. B Snap-in mount edges flush See figure. Front mount round aperture See figure.3 C Front mount round aperture, dome See figure.4, required for UL listed products, Mark IV only S P Z 050M Front mount rectangular aperture flush rocker handle type PCB mount Special specify 50mA A 0A AC or DC 6 x In See figure.5, available on C-Frame Mark IV only See figure.6, with PCB mount terminals only A Standard handle See figure.; for mountings 3, B,, C B Short handle See figure.; for mountings 3, B,, CR only C Cut off handle See figure.3; for mountings 3, B,, C Only handle per Unit H Flush rocker handle See figure.4; for mounting S, Mark IV Only handle per Unit M Two tone flush rocker handle See figure.5; for mounting S, Mark IV Only handle per Unit Y No handle, Blank front plate For reduced handle version, on pole(s) without handle Standard handle, mid trip See figure.6; for mountings 3, B,, C, Mark IV only 5 Flush rocker handle, mid trip pull to reset See figure.7; for mounting S, Mark IV Only handle per Unit 6 Two tone flush rocker handle, mid trip pull to reset For mounting S; Mark IV Only handle per Unit AX M5 or 0-3 stud See figure 3.; 50A max. Mark IV only CX Rear quick connect terminal (0.8mm X 6.35mm) See figure 3.; 5A max. Screw terminal, Bus connected (M4 or 8-3) See figure 3.3; 40A max. Screw terminal, Bus connected (M5 or 0-3) See figure 3.3; 50A max. 3 Screw terminal, Upturned ears (M4 or 8-3) See figure 3.4; 40A max. 3 Screw terminal, Upturned ears (M5 or 0-3) See figure 3.4; 50A max Bent screw terminal, Bus connected (M4 or 8-3) See figure 3.5; 40A max Bent screw terminal, Bus connected (M5 or 0-3) See figure 3.5; 50A max Bent screw terminal, Upturned ears (M4 or 8-3) See figure 3.6; 40A max Bent screw terminal, Upturned ears (M5 or 0-3) See figure 3.6; 50A max. 6 Marine screw terminal (M4 or 8-3) See figure 3.7; 40A max. 6 Marine screw terminal (M5 or 0-3) See figure 3.7; 50A max. 4X M5 flush rear screw terminal See figure 3.8; 50A max.; Mark IV only PX PCB terminal See figure.6 50A max.; CR and Mark IV are different 4P Plug-in terminal ø3.9mm x 9.05mm) See figure 3.9; 50A max.; Mark IV only Z Note pole metric A pole imperial CR four pole max. pole metric B pole imperial 3 3 pole metric C 3 pole imperial 4 4 pole metric D 4 pole imperial 5 5 pole metric E 5 pole imperial 6 6 pole metric F 6 pole imperial J 40V 50/60Hz Common bus at 40V K 77V 50/60Hz Common bus at 77V N 80V DC Mark IV only E 65V DC S 0/40V 50/60Hz 3 wire centre tap supply, 0V per phase, Mark IV only Q 40/45V 50/60Hz 3 Phase multi wire system, Mark IV only R 77/480V Hz 3 Phase multi wire system M 80V DC / 40V 50/60z AC/DC version only with AC and DC curves, Mark IV only L 80V DC / 77V 50/60Hz AC/DC version only with AC and DC curves, Mark IV only System Pulse Tolerance System Pulse Tolerance AS Long delay AC or DC 8 x In CE CH & inertia wheel AC 35 x In A AS & inertia wheel AC or DC 0 x In US Ultra short time delay AC or DC None AH Long delay, high inrush AC 0 x In OP Instantaneous trip AC or DC None AE AH & inertia wheel AC 35 x In AD Long delay, Dual rated AC and DC 8 x In BS Medium delay AC or DC 8 x In BD Medium delay, Dual rated AC and DC 8 x In BI BS & inertia wheel AC or DC 0 x In CD Short delay, Dual rated AC and DC 8 x In BH Medium delay, high inrush AC 0 x In AW AD & inertia wheel, Dual rated AC and DC 0 x In BE BH & inertia wheel AC 35 x In BW BD & inertia wheel, Dual rated AC and DC 0 x In CS Short delay AC or DC 6 x In CW CD & inertia wheel, Dual rated AC and DC 5 x In CI CS & inertia wheel AC or DC 5 x In OX Switch CH Short delay, high inrush AC 5 x In Z H3 Short delay 500 5A 50A XXXX Not applicable No current, for series voltage trip poles AX Switch BX Series trip CX Relay trip Current sensing, centre terminal construction 30A max for the sensing coil; total current 50A max DX Relay trip Voltage sensing, centre terminal construction EX Shunt trip current sensing, 3rd terminal close to load side Total load 50A maximum FX Shunt trip voltage sensing, 3rd terminal close to load side GX Dual control shunt trip construction, 3rd terminal close to load side Voltage coil normally at line voltage; No AH, BH, CH,AE, BE, CE HX Dual control - relay trip construction (4 terminal) No AH, BH, CH, AE, BE, CE JX Switch with auxiliary switch Requires Auxiliary switch KX Series trip, with auxiliary switch Requires Auxiliary switch LX Series trip, with trip-alarma Trip alarm requires mid trip handle and Auxiliary switch Z 9

10 DATA SHEET CBE Range C-Frame Series Circuit Breakers Long Group 0: Auxiliary and Alarm Switches Group : Dual control/ Relay trip Voltage and Current coil ratings Group : Terminals for Shunt, Relay and Dual control construction (CR only code X) Group 3: Voltage for Illuminated Rocker Group 4: Terminal for Illuminated Rocker Group 5: Handle colour A B X Z One change over gold tips, equally spaced terminals One change over silver plated tips, equally spaced terminals Not applicable Special specify 0.0 to 0.A and 30V max. Standard No microswitch - Flat base plate A4 A5 B0 B B B3 0-5V AC 50/60Hz 0-40V AC 50/60Hz V DC 4V DC 48V DC 80V DC For toggle handle type Green with white marking White with black marking Black with white marking Blue with white marking Yellow with black marking Red with white marking For flush rocker handle White (On) / white (Off) black marking Black (On) / black (Off) white marking Green (On) / red (Off) white marking For two tone rocker handle Black face / white indicator + marking Black face / red indicator + marking Black face / green indicator + marking No handle Special specify No marking I - 0 ON - OFF I - 0 and ON - OFF Ampere rating I - 0 and ampere rating ON-OFF and ampere rating I-0 and ON-OFF and ampere rating No Handle Special specify C C C3 XX ZZ 0mA 00mA A Not applicable Special specify A B M4/8-3 screw terminal M5/0-3 screw terminal Figure.; 40A max. Figure.; 50A max. C Quick connect terminal Figure.3; 5A max. X Not applicable Only option for CR Note X Not applicable X Not applicable Note G W B 4 Y R W B G W R G X Z Group 6: Handle Marking A B C D E F G H X Z The coding is dependent on the type of handle. For all handles excluding the flush rocker and two tone flush rocker handles, the colour code describes the colour of the handle. For the flush rocker handle the colour code describes the colour of the on and off actuation buttons by a single code. The two tone handle, the colour code describes the indication colour. The face colour is black and the indicator indicates the off or tripped position (see figure.6). After selecting the appropriate colour code select the marking code, the marking colour of the two tone handle is equivalent to the indicator colour. After selecting the appropriate marking the orientation of print may be specified. For the toggle handle types only codes V and H are applicable (see figure 7.). If the pole has no handle because of it being a reduced handle version use code XXX. Group 7: Handle Orientation V H Vertical Horizontal Vertical Horizontal See figure 7. See figure 7. See figure 7. See figure 7. X No handle Group 8: Front plate colour and marking options Group 9: Inter-phase barrier and terminal cover Group 0: Approvals and typical safety marks (Standard marks and approval basket covers most regions) Group : Optional safety marks B Black front plate no marking Black front plate no marking, with test button for mechanical trip Test button is standard on rocker handle version, on the switch version the button is nonfunctioning and black in colour A Small inter-phase barrier Interphase barriers may be required for multi-pole C Z Inter-phase barrier products that have UL approvals. Contact your nearest X Not applicable CBI sales office for assistance. UL recognized, CSA,VDE 3 4 Z UL Listed, CSA,VDE UL Listed (UL489A), VDE UL recognized, CSA No approvals A UL recognized, only X Special specify C CCC Mark Required for products exported to Peoples Republic of China X Not applicable Only required in specific cases where import into the country is prohibited,unless the product carries the mark. For For Options not not listed listed please please contact contact Emcomp CBI for assistance Example code: C-ASM4XBEBS000AXX-XXXXXWHHBCZC 0

11 DATA SHEET CBE Range C-Frame Series Circuit Breakers PANEL CUTOUT DETAIL (PANEL THICKNESS.0-3.) 4-POLE PANEL CUTOUT DETAIL (PANEL THICKNESS.0-3.) 4-POLE M3 or 6-3 insert Ø 3.5 (M3) Ø4.0 (6-3) PANEL CUTOUT DETAIL M3 or 6-3 insert Ø POLE -POLE 3-POLE 4-POLE POLE -POLE 3-POLE 4-POLE TOLERANCES (+0.) TOLERANCES (+0.) Figure. Figure. Figure.4 Figure.3 PANEL CUTOUT DETAIL Ø 3.5 (M3) 9. Ø4.0 (6-3) 5. M3 or 6-3 insert OFF ON MARK IV.3 CR MARK IV 7.8 OFF ON 3.9 Face colour 66.5 o 6 o 66.5 o Indication colour Figure.5 Figure. Figure. Figure.3 Figure.4 Figure.5 BREAKER ON 0.3* M BREAKER TRIPPED INDICATING ELECTRIC FAULT BREAKER OFF OFF ON PULL TO RESET MID-TRIP PULL TO RESET LINE 34.3 LINE LINE M4 8-3 M5 0-3 * 39.6 TEST BUTTON # * DISTANCE BETWEEN CLAMPING SURFACES # FOR REFERENCE ONLY * DISTANCE BETWEEN CLAMPING SURFACES Figure.6 Figure.7 Figure 3. Figure 3. Figure 3.3 LINE M4 8-3 M * UPTURNED EARS * DISTANCE BETWEEN CLAMPING SURFACES LINE 7.6 # # FOR REFERENCE ONLY o M4 8-3 M5 0-3 #.0 M4 8-3 M5 0-3 LINE 7.6 # 30 o UPTURNED EARS M4 8-3 M # # FOR REFERENCE ONLY LINE 30 o 0.8 # 7.7 # FOR REFERENCE ONLY LINE 6.3 #.9 # FOR REFERENCE ONLY 8. M PLUG-IN HOLE ±0. Ø4.0 LINE Ø Figure 3.4 Figure 3.5 Figure 3.6 Figure 3.7 Figure 3.8 Figure 3.9 TOGGLE HANDLE PC BOARD MOUNTING MARK IV LINE SIDE LOAD SIDE LINE SIDE H LOAD SIDE Ø Ø..0 (TYP) (TYP) M4 8-3 M LINE PCB FOOT PRINT.54 (TYP) AUX-SWITCH OPTIONAL 7.5 Ø.5 (TYP) (7 OFF) 53.9 LINE # * DISTANCE BETWEEN CLAMPING SURFACES # FOR REFERENCE ONLY 9.8* LINE LOAD SIDE V LINE SIDE LOAD SIDE LINE SIDE Figure.6 Figure. Figure. Figure 7.

12 DATA SHEET CBE Range D-Frame Series Circuit Breakers Features - Hydraulic-Magnetic Technology - 00% Rating Capability Independent of Ambient Temperature - Up to Six Poles - culus, VDE and CE Approved - Ratings up to 50A - Optional Trip Alarm Switch and Auxiliary Switch - Wide Range of Circuits, Mountings, Terminations and Time Delays Available - Optional Mid Trip Indication - Two Colour Handle Indication (Two Tone Flush Rocker) Applications - AC and DC Branch Circuit Installations - Telecom DC Power Distribution - UPS Equipment - Mobile Power-Generation Equipment - Power Conditioning - Alternative Energy Equipment - Lighting Control - Marine Protection Technical Data Product Type Circuit Breaker Circuit Breaker Circuit Breaker Approvals culus 489 CE,VDE (EN ) UL489A, CE,VDE (EN60947-) Number of Poles,,, 3 (Parallel) Operating Voltages 0 V AC, 80V DC, 0/40V AC 40V AC, 80V DC 80V DC Current Ratings 0.-80A ac, 00A dc(p), 0.-50A(p) 0.-50A(ac) 0.-00A(dc) 0-50A Interrupting capacity 0kA, 5kA(p) 5kA 0kA Product Type Approvals Number of Poles Operating Voltages Current Ratings Interrupting capacity Vibration Resistance Shock Resistance Operating Temperature Range Switch Circuit Breaker Circuit Breaker culus 508, CE, VDE (EN ), 0V AC, 0/40V AC 50A 600 A (For sec) curus 077 CE,VDE (EN to 6 to 4 80V DC, 77V AC, 77/480 V AC 80V DC, 40V AC, 40/45V AC A (p), A (-6p) A (qp), 0.-70A (-4p) ka ac, 5kA dc 3kA ac, 5kA dc 0G to MIL-STD-0F Method 04D Test A 00G to MIL-STD-0F Method 3B Test A -40 O C to +85 O C Preferred Standard Delays TRIP TIME IN SECONDS /60Hz DC NOTE: 8 x INRUSH } LONG DELAY CODE: AS TYPICAL TIME/CURRENT CHARACTERISTICS AT 5 C TRIP TIME IN SECONDS /60Hz } LONG DELAY DC CODE: BS NOTE: 8 x INRUSH TYPICAL TIME/CURRENT CHARACTERISTICS AT 5 C PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT /60Hz } LONG DELAY DC CODE: CS NOTE: 6 x INRUSH /60 Hz DC } CODE: OP LONG DELAY TRIP TIME IN SECONDS 0 0. TYPICAL TIME/CURRENT CHARACTERISTICS AT 5 C TRIP TIME IN SECONDS 0 0. TYPICAL TIME/CURRENT CHARACTERISTICS AT 5 C PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT 50

13 DATA SHEET CBE Range D-Frame Series Circuit Breakers Long Group 0: Frame D D-Frame Group : Type D-Frame D Type UL Recognized approvals only D-Frame DD Type UL Listed and UL recognized approvals Group : Mounting A Front mount rectangular aperture toggle handle type See figure. B Snap-in mount edges flush See figure., available on D-Type only D Centre lock mounting See figure.3, available on D-Type only S Front mount rectangular aperture flush rocker handle type See figure.4, available on DD-Type only Group 3: Handle or Pole Blank (Reduced Handle) A Standard handle See figure.; for mountings A, B B Short handle See figure.; for mountings A, B; D-Type only C Cut off handle See figure.3; for mountings A, B; only handle per unit D Paddle handle See figure.4; for mounting D; only handle per unit E Baton handle See figure.5; for mounting D; only handle per unit H Flush rocker handle See figure.6; for mounting S; only handle per unit M Two tone flush rocker handle See figure.7; for mounting S; only handle per unit W No handle, Blank front plate, D-frame type For reduced handle version, on pole without handle Standard handle, mid trip See figure.8; for mountings A, B 5 Flush rocker handle, mid trip pull to reset See figure.9; for mounting S; only handle per unit 6 Two tone flush rocker handle, mid trip pull to reset See figure.0; for mounting S; only handle per unit Group 4: Main Terminal AX M5 or 0-3 stud See figure 3.; 60A max. BX Clamp terminal M3 or 6-3 See figure 3.; 30A max.; D-Type only CX Rear quick connect terminal (0.8mm X 6.35mm) See figure 3.3; 5A max.; D-Type only MX M6 or /4-0 stud terminals See figure 3.4; 00A max. X Plug in terminal (Ø6.5mm X.5mm) See figure 3.5; 50A max. 3X Plug in terminal (Ø7.80mm X.5mm) See figure 3.6; 00A max. 4X M5 or 0-3 flush rear screw terminal See figure 3.7; 50A max.; DD-Type only VI Bridge terminal for pole parallel construction See figure A max.; DD-Type only Group 5: Number of Poles Group 6: Rated Voltage and Frequency Group 7: Time Delay (For details of time delay refer to the application guide or web site) Group 8: Main Circuit Current (Example only, any ampere rating possible) Group 9: Circuit Configuration Group 0: Auxiliary and Alarm Switches W Bridge terminal for 3 pole parallel construction See figure 3.9; 50A max.; DD-Type only XX No Terminal Z pole metric A pole imperial pole metric B pole imperial 3 3 pole metric C 3 pole imperial 4 4 pole metric D 4 pole imperial 5 5 pole metric E 5 pole imperial 6 6 pole metric F 6 pole imperial J 40V 50/60Hz Common bus at 40V K 77V 50/60Hz Common bus at 77V N 80V DC S 0/40V 50/60Hz 3 wire centre tap supply, 0V per phase Q 40/45V 50/60Hz 3 Phase multi wire system R 77/480V Hz 3 Phase multi wire system M 80V DC / 40V 50/60z AC/DC version only with AC and DC curves L 80V DC / 77V 50/60Hz AC/DC version only with AC and DC curves System Pulse Tolerance System Pulse Tolerance AS Long delay AC or DC 8 x In CE CH & inertia wheel AC 35 x In A AS & inertia wheel AC or DC 0 x In US Ultra short time delay AC or DC None AH Long delay, high inrush AC 0 x In OP Instantaneous trip AC or DC None AE AH & inertia wheel AC 35 x In AD Long delay, Dual rated AC and DC 8 x In BS Medium delay AC or DC 8 x In BD Medium delay, Dual rated AC and DC 8 x In BI BS & inertia wheel AC or DC 0 x In CD Short delay, Dual rated AC and DC 8 x In BH Medium delay, high inrush AC 0 x In AW AD & inertia wheel, Dual AC and DC 0 x In BE BH & inertia wheel AC 35 x In BW BD & inertia wheel, Dual AC and DC 0 x In CS Short delay AC or DC 6 x In CW CD & inertia wheel, Dual AC and DC 5 x In CI CS & inertia wheel AC or DC 5 x In OX Switch (series V coil) CH Short delay, high inrush AC 5 x In Z H3 Short delay 050M K00 XXXX 50mA A 0A 50A 00A AC or DC 6 x In No current, for voltage trip poles AX Switch BX Series trip CX Relay trip Current sensing, centre terminal construction 50A max for the sensing coil; total current 00A max DX Relay trip Voltage sensing, centre terminal construction EX Shunt trip current sensing, 3rd terminal close to load side Total load 00A maximum FX Shunt trip voltage sensing, 3rd terminal close to load side GX Dual control shunt trip construction, 3rd terminal close to load side Voltage coil normally at line voltage; No AH, BH, CH,AE, BE, CE HX Dual control - relay trip construction (4 terminal) No AH, BH, CH, AE, BE, CE JX Switch with auxiliary switch KX Series trip, with auxiliary switch LX Series trip, with trip-alarm Trip alarm requires mid trip handle Z A One change over gold tips, equally spaced terminals 0.0 to 0.A Max 30V B One change over silver plated tips, equally spaced terminals M Integrated micro switch housing, silver tips X Z Not applicable Special specify Required for parallel bridged DD-Type on last pole. See figure 3.8 and 3.9 No auxiliary switch - Flat base plate 3

14 DATA SHEET CBE Range D-Frame Series Circuit Breakers Long Group : Dual control/ Relay trip Voltage and Current coil ratings Group : Terminals for Shunt, Relay and Dual control construction Group 3: Voltage for Illuminated Rocker Group 4: Terminal for Illuminated Rocker Group 5: Handle colour A4 0-5V AC 50/60Hz C 0mA A5 B0 B B B3 0-40V AC 50/60Hz V DC 4V DC 48V DC 80V DC C C3 XX ZZ 00mA A Not applicable Special specify B M5/0-3 screw terminal Figure.; 50A max. C E X Note X Not applicable X Not applicable Note For toggle handle type G Green with white marking W White with black marking B Black with white marking 4 Blue with white marking Y Yellow with black marking R Red with white marking For flush rocker handle W White (On) / white (Off) black marking B Black (On) / black (Off) white marking G Green (On) / red (Off) white marking For two tone rocker handle W Black face / white indicator + marking R Black face / red indicator + marking G Black face / green indicator + marking X No handle A No marking B I - 0 C ON - OFF D I - 0 and ON - OFF E Ampere rating F I - 0 and ampere rating G ON-OFF and ampere rating H I-0 and ON-OFF and ampere rating X No Handle Group 7: Handle Orientation V Vertical H Horizontal Vertical X Horizontal No handle A Black front plate standard marking I-0, ON-OFF and Amp rating Black front plate no marking, with test button for mechanical trip Test button is standard on mid trip rocker handle version Z Quick connect terminal M5 studs terminal Not applicable Group 6: Handle Marking Group 8: Front plate colour and marking options Group 9: Inter-phase barrier and terminal cover (Interphase barriers and terminal covers are required for UL listed Approvals) Group 0: Approvals and typical safety marks (Standard marks and approval basket covers most regions) A Small inter-phase barrier B Large inter-phase barrier Interphase barriers and terminal covers may be required C Z Inter-phase barrier Terminal cover(s) for multi-pole products that have UL listed approvals and Small inter-phase barrier and terminal cover UL recognized approvals. See the application guide for the 3 Large inter-phase barrier and terminal cover D/DD frame for details, or contact your nearest CBI sales 4 Z inter-phase barrier and terminal cover X Not applicable office for assistance. UL recognized, CSA,VDE, CE UL Listed, CSA,VDE, CE UL Listed (UL489A), VDE UL recognized, CSA UL recognized, only No approvals Special specify Figure.; 5A max. Figure.3; 60A max. For illuminated handle versions please contact your nearest CBI office for assistance. The coding is dependent on the type of handle. For all handles, excluding the flush rocker and two tone flush rocker handles, the colour code describes the colour of the handle. For the flush rocker handle the colour code describes the colour of the on and off actuation buttons by a single code. The two tone handle the colour code describes the indication colour. The face colour is black and the indicator indicates the off or tripped position (see figure.7). After selecting the appropriate colour code select the marking code.the marking colour of the two tone handle is equivalent to the indicator colour. After selecting the appropriate marking, the direction of print may be specified. For the toggle handle types only codes V and H are applicable (see figure 5.). If the pole has no handle because of it being a reduced handle version use code XXX. See figure 5. The diagram only shows the flush rocker printing, which has the opposite printing position (ON/OFF) to other handle types if the breaker needs to be reverse fed then the printing will be upside down and codes and should be selected. For VDE, CE normally IEC/EN60934 For VDE, CE normally IEC/EN A Z X Group : Optional safety marks C X Z CCC Mark Not applicable Special specify Required for products exported to Peoples Republic of China Only required in specific cases where import into the country is prohibited, unless the product carries the mark. For Options For Options not listed not listed please please contact contact Emcomp CBI for for assistance assistance Example code: D-SM4XBSOXAXX-XXXXXWHHBCZC 4

15 DATA SHEET CBE Range D-Frame Series Circuit Breakers 5.4 [.063] 4.6 [0.8] Ø4.0 [0.57] 36.8 [.449] 9.0 [0.748] M3 OR 6-3 MOUNTING INSERT 9.0 [0.748] 77.5 [3.05] 7. [.803] 9. [0.756] Ø6.0 [0.36] 3.5 [0.38] 0.0 [0.394] Ø8.0 [0.709] M x (FINE PITCH) /-3 (UN) 5. FOR METRIC [0.7] FOR IMPERIAL M3 or 6-3 Ø4.0 [0.57] Ø3.0 [0.5] 6.7 [0.657] [0.748] M3 OR 6-3 [0.756] MOUNTING INSERT 5. [0.05] Ø4.0 [0.57] [.66] [.5] 9. [0.756] 50.7 [.996] 8.5 Figure. Figure. Figure.3 Figure OFF O 00 ON I OFF POSITION Figure. Figure. Figure.3 Figure.4 Figure.5 Figure ON I Indication colour Face colour Indication colour TRIPPED OFF TEST BUTTON ALARM o 60A OFF O 00 ON I OFF POSITION TRIPPED POSITION TEST BUTTON Face colour Figure.7 HANDLE IN MID POSITION INDICATING BREAKER TRIPPED Figure.8 Figure.9 Figure CAPTIVE NUT AND M4 X 8 OR 0-3 SCREW ± Figure * * DISTANCE BETWEEN CLAMPING SURFACES Figure 3. 0 Figure ± Ø6.35 (Ø0.50) FOR Ø6.5 [Ø0.46] BULLET TERMINAL (-0.5).5 Ø7.90 [Ø0.3] FOR Ø7.80 [Ø0.307] BULLET TERMINAL (-0.5) Figure Figure Figure 3.6 External bridge Internal bridge External bridge Internal bridge M5 or 6-3 screw star washer and flat washer 3.* 0.0 LOAD LINE 5.9 M5 or 0-3 SCREW FLAT AND STAR WASHER # * TO CLAMPING SURFACE 3. 7.* Figure Figure Figure 3.9 * TO CLAMPING SURFACES # FOR REFERENCE ONLY Figure. LINE SIDE LOAD SIDE LINE SIDE H LOAD SIDE LOAD LINE LOAD LINE 9.0 (±0.5) LOAD SIDE LINE SIDE Figure. Figure.3 LOAD SIDE V LINE SIDE Figure 5. 5

16 CBE Range Q-Series miniature circuit breakers (3 & 8mm module widths) Product Type QA/QF (3) QF (8) QZ (3) QY/QDC (3) Standard Ampere Ratings (A) (QA) 0. 5 (QF) (UL 077) 5 50 (EN60947-) 5 63A (QA, No approvals) Number of Poles,, 3, +N, 3+N,, 3, +N, 3+N,, 3, +N, 3+N Rated Voltage (V) Approvals & Interrupt. Capacity (ka) Mounting Options Tripping curves Resistance to shock Vibration Operating temperature Optional Accessories Features * Polarity Sensitive VDE (EN ) CE UL489A curus (UL077_CSA) Dual (DIN & Mini Rails) DIN Rail Surface Clip Plug-in 0V AC, p (QF only) 0/40V AC, p (QF only) 40V AC (p, p+n) 40/45V AC (, 3, 3p+N) 3kA (QA) 6kA (QF) 5kA (0/40V AC) (QF) 40V AC (p, p+n) 40/45V AC (, 3, 3p+N) 77V AC (p) 77/480V AC (, 3p) 6kA (40/45V AC) 3kA (77/480V AC) 40V AC (p, p+n) 40/45V AC (, 3, 3p+N) 77V AC (p) 77/480V AC (, 3p) 3kA (40/45V ac) 5kA (77/480V ac) ( pole) ( poles) 0 00 (p parallel) 0 50 (3p parallel),, 3p parallel poles in series 80V DC *5V DC (, p & p parallel) *50V DC (p in series) 0kA,, 3, 9, OP,, 3, 9, OP,, 3, 9, OP OP, U, U3,, 9 IEC , 5G/30ms half sine wave IEC 77/IEC , 3G/0-50Hz -40 C to +65 C Aux. switch Trip alarm Aux. switch + trip alarm Shunt trip Handle lock Bus bar Shroud Compact 3/8mm module widths Hydraulic-magnetic technology Precision tripping Suitable for isolation Temperature independent trip point Mid trip handle 0kA (QY only) 6

17 CBE Range Q-Series miniature circuit breakers (3 & 8mm module widths) Features QA/QF(3) QZ(3) QY/QDC(3) - AC circuit breakers - AC circuit breaker - DC circuit breakers - curus Recognized (QF) - curus recognized - VDE, CE Approved - VDE, CE Approved - VDE & CE Approved - UL 489A Listed (QY only) - One to four pole units - One to four pole units - One & two pole units - Current ratings up to 50A - Current ratings up to 60A - Current ratings up to 50A - 80, 5 & 50V dc versions (50V dc poles in series) 74 (.9) 65 (.56) 66 (.6) 7.9 (0.7) 60 (.36) 3 (0.5) 6 (.0) 39 (.54) 9 (0.75) DUAL MOUNT DIN RAIL MOUNT Features QF(8) - AC circuit breaker - UL 077 Recognized - VDE, CE, CSA certified - One to four pole units - Current ratings up to 63A 68 (.68) 60 (.36) 36 (.4) 54 (.3) 7 (.84).5 (0.89) 45 (.77) 85.5 (3.37) 7.4 (.8) 0.5 (0.797) 7.4 (.8) 8.5 (.) 57 (.4) 45 (.77) 96.8 QZ only (3.8) 9.8 (3.65) 35 (5.3) 5 (5.95).5 (0.86) 5.9 (0.94) 5 (0.) 3 (.6) 45 (.77) 64.8 (.55) 5.0 (0.) 44 (.73) 63.8 (.5) 73 (.87) 3 (0.5) NOTE: DIMENSIONS IN BRACKETS ARE IN INCHES QY/QDC, & 3 POLES QY / QDC, & 3 POLES BRIDGED IN PARALLEL IN PARALLEL 5 (0.) 9 (0.75) 3 (.) 44 (.73) 63.8 (.5) 8 (0.7) 8 (0.7) 7

18 CBE Range Q-Series miniature circuit breakers (3 & 8mm module widths) Features Auxiliary switch and/or Trip alarm switch - AC and DC voltages - UL 489 listed (5A, 50V AC; 0.5A, 80V DC Auxiliary; 0.5A, 5V DC Trip alarm) - IEC approved (5A, 50V AC; 0.5A, 0V DC Auxiliary; 0.5A, 5V DC Trip alarm) - Factory fitted - Compact 6.5mm width - Attached to right hand side of circuit breaker - Available on Dual and DIN rail mounting 6.5 (0.56) 5. (0.99) (N/O)6 (N/C)8 (C) (.9) 0. (0.79) 6. (.03) (N/O)6 (N/C)8 (C)5 3.3 (.3). (0.83) TRIP ALARM Q. CONNECTORS (0.08) 0.5 (0.0) 5.5 (0.) 45.0 (.77) 57.0 (.4) AUX SWITCH Q. CONNECTORS (C) (N/C) 4(N/O) (C) (N/C) 4(N/O).8 (0.) 7 (0.8) 9.5 (0.77) Standard Time Delay Curves 0.3 (0.8) 3.9 (.6) 9.7 (0.38) DIN RAIL MOUNT.3 (0.84) 3.9 (.3) DUAL MOUNT 0.7 (0.4) 0.5 (0.0) TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE 3 TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE (%) RATED CURRENT (%) RATED CURRENT (%) RATED CURRENT (%) RATED CURRENT TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS CURVE U DC (4% RIPPLE FACTOR) AMBIENT TEMPERATURE 30 C TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS CURVE U3 DC (4% RIPPLE FACTOR) AMBIENT TEMPERATURE 30 C TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE OP INSTANTANEOUS DC (4% RIPPLE FACTOR) INTERNAL IMPEDANCE [Ohms] INTERNAL IMPEDANCE vs CURRENT RATING CURRENT RATINGS [Amps] AC DC (%) RATED CURRENT (%) RATED CURRENT (%) RATED CURRENT 8

19 CBE Range Q-Series miniature circuit breakers (3 & 8mm module widths) Long Group : Frame Type Group : Group 3: Auxiliary Group 4: Number of Poles Group 5: Module width Frequency Approvals QA(3) QF(3) QF(8) QZ QY QDC AC AC AC AC DC DC VDE, CE curus,vde, CE CURus,VDE,CE CURus,VDE,CE UL489A VDE, CE VDE, CE N S A T AT Neutral Switch Auxiliary Switch Trip Alarm Auxiliary Switch + Trip Alarm Single Pole Double Pole Triple Pole Four Pole 3mm 8mm Leave blank if not applicable Leave blank if not applicable Example codes: QA-(3)-DM--0A QF-A-(3)-D--5A QF-N-AT-4(8)-D-9-60A QZ-T-3(3)-D--60A QDC-(3)-DM-U-50A-T3 QY-A-3(3)-D-U-50A-B0 Group 6: Mounting D DM P P DIN 45mm Escutcheon Dual Mount DIN & Mini-Rail, 57mm Escutcheon Plug-in, DIN Plug-in, Dual Mount Group 7: Time Delays 3 9 U U3 OP Curve Curve Curve 3 Curve 9 Curve U Curve U3 Instantaneous Group 8: Current Ratings Group 9: B0 B B T3 Z 0.A 0.A 0.5A A.5A A.5A 3A 4A 5A 6A 0A 5A 6A 0A 5A 30A 3A 35A 40A 45A 50A 60A 63A 70A 80A 00A 5A 50A 80V DC Bottom Connected (Positive at bottom) 5V DC Bottom Connected (Positive at bottom) 50V DC Bottom Connected (Positive at bottom) 50V DC with + & connecting terminals at top DC Bridged (Link not supplied) For more ratings consult factory Leave blank if not applicable A member of the Group South Africa CBI-electric: low voltage Tripswitch Drive Elandsfontein Gauteng South Africa Tel: Fax: cbi@cbi-electric.com Website: Germany CBI-electric: Europe Zeppelinstr. 4 D-878 Puchheim, Germany Tel: Fax: office@cbibreakers.de Website: USA CBI-electric: North America 35E Uwchlan Ave Suite 38 Exton PA 934 USA Tel: Fax: info@cbibreakers.com Website: Australia CBI-electric: Australia 8 Springvale Road Mulgrave Melbourne Victoria 370 Australia Tel: Fax: heinelec@heinelec.com.au Website: 9 July 007/June Viljoen Print Design Print

20 QF4-D Range Earth Leakage Applications - Residential and commercial applications requiring high sensitivity earth leakage protection from electrical shock and fire hazards - Surface and DIN Rail mounting options Features - SANS 767 and VC 8035 approved, as required by SANS 04 - Compact width (36mm wide) - Energy limiting capability on both switch and circuit breaker versions - Switch version fitted with short circuit protection for additional safety - Top busbar design enables easier installation - Single pole plus switched neutral earth leakage protection - Hydraulic Magnetic technology results in accurate temperature independent tripping - Current ratings up to 63A - Trip indication (mid trip handle position) - Improved terminal visibility Technical Data Product Type Standard Ampere Ratings (A) Sensitivity (ma) Number of Poles Equipment Type Rated Voltage (V) Rated Interrupting/ Withstand Capacity (ka) Mounting Options DIN Rail Surface Weight (kg) Mechanism Tripping Curves () (standard) Operating Temperature QF4A-D 5 to 63A 30 + N Earth Leakage 30 5 ka 0,6 Hydraulic-Magnetic and Earth Leakage (),3 QF4C-D 40 and 63A 30 + N Earth Leakage 30 5 ka 0,4 Magnetic and Earth Leakage -0 0 C to C 0

21 QA4-D & QF4-D Range Earth Leakage N N QF4A/QF4C

22 DATA SHEET QA7 & QF7 RANGE Residential/Commercial protection Applications - Commercial applications requiring high sensitivity earth leakage protection from electrical shock and fire hazards. - Installations exposed to high and low ambient temperatures. The hydraulic magnetic design allows the device to always keep rated current. Features - CE approved. - UL077 and UL053 certified. - VDE certified to DIN EN and Small frame size (6mm wide). - Energy limiting capability on both switch and circuit breaker versions. - Switch version fitted with short circuit protection for additional safety. - Top busbar design enables easier installation - Single pole plus switched neutral earth leakage protection - Trip point is unaffected by ambient temperature - Current ratings up to 63A - Trip indication (mid trip handle position) Technical Data Product Type QA7A QA7C QF7A QF7C Standard Ampere Ratings (A) 5 to 63 A 40 and 63 A 5 to 63 A 40 and 63 A Sensitivity (ma) 30, 00, , 00, , 00, , 00, 300 Number of Poles + N + N + N + N Equipment Type Earth Leakage Earth Leakage Earth Leakage/GFCS Earth Leakage/GFCS Rated Voltage (V) Rated Interrupting/ 3 ka 6 ka Withstand Capacity (ka) 3 ka 6 ka Weight (kg) 0,6 0,4 0,6 0,4 Tripping Curves () (standard) (),3 Operating Temperature -40 to +60ºC -40 to +80ºC -40 to +80ºC -40 to +80ºC

23 DATA SHEET QA7 & QF7 RANGE Residential/Commercial protection Technical Data DUAL 66 (.59) 6 (.0) 7.4 (0.68) 8.0 (0.3) 93 (3.66) 8.4 (3.4) 57 (.4) 7.4 (.8) 7.8 (0.30) 36.7 (.66).5 to.5 (0.06 to 0.09) TOP BUSBAR 45 (.77) 69.8 (.74) 74 (.9) DIN 73 (.87) 65 (.56) 6 (.0) 6.4 (0.646) 8.0 (0.35) 93 (3.66) 8.4 (3.4) 7.4 (.8) 45.0 (.77) 7.8 (0.307) 35.7 (.406) 44 (.73) 68.8 (.7) 3

24 CBE Range Q Series Miniature Circuit Breakers Product Type QL QY QZ QDC Standard Ampere Ratings (A) ( pole) ( poles) (UL 077) 5 50 (IEC ) (p parallel) 0 50 (3p parallel) Number of Poles,, 3, +N, 3+N,,, 3, +N, 3+N, 3p parallel Rated Voltage (V) Approvals & Interrupt. Capacity (ka) Mounting Options Tripping curves Resistance to shock Vibration Operating temperature Optional Accessories Features VDE (EN ) CE culus (UL489_CSA) UL489A curus (UL077_CSA) Dual Mounting (DIN & Mini) DIN Rail Surface Clip Plug-in 0V AC (p) 0/40V AC(p) 40V AC (p) 40/45V AC, 4p) 6kA (40/45V AC) 0kA (0/40V AC) 80V DC 5V DC (, p & p parallel) Polarity sensitive 0kA 0kA 0V AC (p) 40V AC (p) 40/45V AC (, 4p) 77V AC (p) 77/480V AC (, 3p) 3kA (40/45V AC) 5kA (p, 0V ac) 5kA (77/480V ac), 9, KM OP, U,, 9,, 3, 9 OP, U,, 9 IEC , 5G/30ms half sine wave, QL-range: consult factory IEC 77/IEC , 3G/0-50Hz, QL-range: consult factory -40 C to +65 C Aux. switch Trip alarm Aux. switch + trip alarm Bus bar Handle lock Compact 3mm/module width Hydraulic-magnetic technology Precision tripping Suitable for isolation Temperature independent trip point Mid trip handle ( pole) ( poles) 0 00 (p parallel) 0 50 (3p parallel),, 3p parallel poles in series 80V DC 5V DC (, p & p parallel) 50V DC (p in series) Polarity sensitive 0kA 4

25 CBE Range Q Series Miniature Circuit Breakers Features QL QY QDC - AC circuit breaker - DC circuit breaker - DC circuit breaker - UL 489 Listed - UL 489A listed - VDE and CE Approved - VDE, CSA, CE Approved - VDE & CE Approved - One and two pole units - One and two pole units - One and two pole units - Current ratings up to 50A - Current ratings up to 5A - Current ratings up to 50A - 80V DC 5V DC and - 80V dc & 5V DC 50V DC (50V DC poles in series) 74 (.9) 65 (.56) 66 (.6) 7.9 (0.7) 60 (.36) 3 (0.5) 6 (.0) 39 (.54) DUAL MOUNT Features DIN RAIL MOUNT QZ - AC circuit breaker - UL 077 Recognized - VDE, CE, CSA certified - One, two and three pole units - Current ratings up to 60A 74 (.9) 65 (.56) 66 (.6) 9.9 (0.78) 60 (.36) 3 (0.5) 7.4 (.8) 57 (.4) 45 (.77) 96.8 (3.8) 8.5 (.).5 (0.86) 5.9 (0.94) 7.4 (.8) 57 (.4) 45 (.77) 9.8 (3.65) 35 (5.3) 5 (5.95) 8.5 (.).5 (0.86) 5.9 (0.94) 5 (0.) 9 (0.75) 3 (.6) 45 (.77) 64.8 (.55) 5.0 (0.) 44 (.73) 63.8 (.5) 73 (.87) 3 (0.5) NOTE: DIMENSIONS IN BRACKETS ARE IN INCHES QY/QDC, / QDC, & 3 POLES BRIDGED PARALLEL BRIDGED IN PARALLEL 6 (.0) 39 (.54) 5 (0.) 9 (0.75) 3 (.6) 45 (.77) 64.8 (.55) 5.0 (0.) 44 (.73) 63.8 (.5) 73 (.87) 3 (0.5) NOTE: DIMENSIONS IN BRACKETS ARE IN INCHES DUAL MOUNT DIN RAIL MOUNT 5

26 CBE Range Q Series Miniature Circuit Breakers Features Auxiliary switch,trip alarm, Combo - AC and DC voltages - UL 489 listed (5A, 50V AC; 0.5A, 80V DC Auxiliary; 0.5A, 5V DC Trip alarm) - IEC approved (5A, 50V AC; 0.5A, 0V DC Auxiliary; 0.5A, 5V DC Trip alarm) - Factory fitted - Compact 6.5mm width - Attached to right hand side of circuit breaker - Available on Dual and DIN rail mounting 6.5 (0.56) 5. (0.99) (N/O)6 (N/C)8 (C) (.9) 0. (0.79) 6. (.03) (N/O)6 (N/C)8 (C)5 3.3 (.3). (0.83) TRIP ALARM Q. CONNECTORS (0.08) 45.0 (.77) 0.5 (0.0) 5.5 (0.) 57.0 (.4) AUX SWITCH Q. CONNECTORS (C) (N/C) 4(N/O) (C) (N/C) 4(N/O).8 (0.) 7 (0.8) 9.5 (0.77) 0.3 (0.8) 3.9 (.6) 9.7 (0.38).3 (0.84) 3.9 (.3) 0.7 (0.4) 0.5 (0.0) Standard Time Delay Curves TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE 3 TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE (%) RATED CURRENT (%) RATED CURRENT (%) RATED CURRENT (%) RATED CURRENT TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE KM TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS CURVE U DC (4% RIPPLE FACTOR) AMBIENT TEMPERATURE 30 C TRIPPING TIME SECONDS MINUTES OPERATING CHARACTERISTICS AMBIENT TEMPERATURE 30 C CURVE OP INSTANTANEOUS DC (4% RIPPLE FACTOR) OPERATING TIME VARIATION (%) DIN RAIL MOUNT DUAL MOUNT AMBIENT TEMPERATURE TIME VARIATION FOR HYDRAULIC-MAGNETIC CIRCUIT BREAKERS.5 0 AMBIENT TEMPERATURE ( C) (%) RATED CURRENT (%) RATED CURRENT (%) RATED CURRENT 6

27 CBE Range Q Series Miniature Circuit Breakers Long Group : Frame Type Group : Group 3: Auxiliary Group 4: Number of Poles Group 5: Module width Group 6: Mounting Group 7: Time Delays Group 8: Current Ratings Group 9: Frequency Approvals QL QY QZ QDC AC DC AC DC UL 489 UL489A,VDE, CE CURus,VDE,CE EN , CE N S A T AT D DM P P 3 9 U KM OP B0 B B Z Neutral Switch Auxiliary Switch Trip Alarm Auxiliary Switch + Trip Alarm Single Pole Double Pole Triple Pole Four Pole 3mm 8mm 9.5mm 6mm DIN 45mm Escutcheon Dual Mount DIN & Mini-Rail, 57mm Escutcheon Plug-in, DIN Plug-in, Dual Mount Curve Curve Curve 3 Curve 9 Curve U Curve KM Instantaneous 0.A 0.A 0.5A A.5A A.5A 3A 4A 5A 6A 0A 5A 6A 0A 5A 30A 3A 35A 40A 45A 50A 60A 63A 70A 80A 00A 5A 50A 80V DC Bottom Connected (Positive at bottom) 5V DC Bottom Connected (Positive at bottom) 50V DC Bottom Connected (Positive at bottom) DC Bridged (Link not supplied) Leave blank if not applicable Leave blank if not applicable Leave blank if not applicable Example codes: INTERNAL IMPEDANCE vs CURRENT RATING INTERNAL IMPEDANCE [Ohms] QY-(3)-D-U-0A-B QDC-(3)-DM-U-50A-B QL-A-(3)-D-9-5A QZ-N-AT-4(3)-DM-60A AC DC CURRENT RATINGS [Amps] 7

28 DATA SHEET Surge Protection 5kA and 0kA Rail Mounted Surge Protective Devices Features - SANS approved - Compact size (3mm per pole) - Clip-in, Dual mounting (Mini rail and DIN rail) - LED indication of the SPD s condition whilst ON, the SPD is functional, if OFF and the mains power is still available, then the SPD is no longer functional and should be replaced - Thermal disconnect device (prevents potential thermal runaway problems) - One port SPD (no series impedance) - Voltage limiting/clamping-type SPD (MOV) - IP 0 rating Applications - For surge protection on incoming power supply in lightning protection zones OB to or to in compliance with SANS 04- [The Wiring of Premises]. - For maximum efficiency, ensure that the installation is earthed in accordance with SANS IEC 63. Technical Data Product Type Max. Continuous Operating Voltage (Uc) (Please specify desired voltage) Voltage Protection Level (Up) Nominal Discharge Current (In) Maximum Discharge Current (Imax) Short Circuit Withstand* Lightning Protection Zone SPD Class QFL-(3), QFL-(3)D QFL-3(3), QFL-3(3)D QFLN-(3), QFLN-(3)D QFLN-4(3), QFLN-4(3)D 30V 0.7kV 5kA (8/0 µs) 0kA (8/0 µs),5ka (50Hz) OB to or to Class II 75V AC (RMS).5kV QKL-(3), QKL-(3)D QKL-3(3), QKL-3(3)D QKLN-(3), QKLN-(3)D QKLN-4(3), QKLN-4(3)D 75V AC (RMS).5kV 0kA (8/0 µs) 40kA (8/0 µs) 5kA (50Hz) OB to or to Class II *Backed up by a suitable short circuit protection device (SCPD) * For Prospective Short Circuit Currents up to,5ka: Use any QA circuit breaker * For Prospective Short Circuit Currents up to 5kA: Use any QF circuit breaker * For Prospective Short Circuit Currents above 5kA: Contact CBI-electric:low voltage 8

29 CBI DATA SHEET DATA SHEET Surge Protection 5kA and 0kA Rail Mounted Surge Protective Devices Wiring Precautions L 5 L L 5 L - For maximum efficiency, the installation should be earthed according to SANS 63 - If the distance of N and E is >0m from the separating point P on a TN-C-S system, use a pole device (P+N). - (For details refer to SANS 04-). L L3 PEN 7 Point of control 6 4 S P D 3 S P D TN-C-S S P D S P D E L L3 N PE L L3 N PE Point of control 4 S P D 3 S P D TN-S* S P D DIMENSIONAL DATA 57mm Escutcheon (Mini Rail Mounting) H W D P P P P DIMENSIONAL DATA 45mm Escutcheon (DIN Rail Mounting) S P D E L L3 N PE *SINGLE PHASE 5 H W D P P P P Slide yellow clip up and down as indicated to install and remove the unit. MOUNTING AND INSTALLATION Mini Rail DIN Rail 9

30 Emcomp International AB Phone: +46 (0) Box 7 Fax: +46 (0) SE 70 4 Fellingsbro SWEDEN CBI@emcomp.se