MODEL TUNS50F05 TUNS50F12 TUNS50F24 VOLTAGE[V]

Size: px

Start display at page:

Download "MODEL TUNS50F05 TUNS50F12 TUNS50F24 VOLTAGE[V]"

Joan Delilah Dawson
6 years ago
Views:

with Mounting hole (f3. thru) *Avoid short circuit between +BC and -BC. It may cause the failure of inside components. *Keep TM open, if output voltage adjustment is not necessary.

1 AC-DC Power Supplies Bus Converter. Power Module Type 50F Ordering information TUN S 50 F 05 -O * Providing heat sink as option 1 Series name 2 Single output 3 Output wattage Universal Input 5 Output voltage 6 Optional T : with Mounting hole (f3. thru) *Avoid short circuit between +BC and -BC. It may cause the failure of inside components. *Keep TM open, if output voltage adjustment is not necessary. MODEL 50F05 50F12 50F2 MAX OUTPUT WATTAGE[W] DC OUTPUT 5V 10A 12V.2A 2V 2.1A MODEL 50F05 50F12 50F2 AC f (Please refer to the instruction manual, 6.5 Derating) CUENT[A] ACIN 100V 0.67typ (Io=100%) ACIN 200V 0.35typ (Io=100%) FEQUENCY[Hz] 50/60 (7-63) ACIN 100V 79typ 83typ 8typ ACIN 200V 81typ 8typ 86typ POWE FACTO (Io=100%) ACIN 100V 0.95typ ACIN 200V 0.90typ INUSH CUENT Limited by external components (Thermistor) LEAKAGE CUENT[mA] 0.75max (ACIN 20V 60Hz, Io=100%, According to IEC ) CUENT[A] LINE EGULATION[mV] 10max 2max 8max LOAD EGULATION[mV] 10max 2max 8max 0 to +100C *1 80max 120max 120max IPPLE[mVp-p] -0 to 0C *1 120max 150max 150max 0 to 15% Load *1 200max 280max 380max OUTPUT 0 to +100C *1 120max 150max 150max IPPLE NOISE[mVp-p] -0 to 0C *1 200max 200max 250max 0 to 15% Load *1 280max 360max 60max TEMPEATUE EGULATION[mV] 0 to +65C 50max 120max 20max -0 to +100C 100max 20max 80max DIFT[mV] *2 20max 0max 90max OUTPUT VOLTAGE ADJUSTMENT ANGE[V] Fixed (TM pin open), adjustable by external resistor or external signal OUTPUT VOLTAGE SETTING[V] POTECTION CICUIT AND OVECUENT POTECTION Works over 105% of rating and recovers automatically OVEVOLTAGE POTECTION[V] EMOTE SENSING Not provided EMOTE ON/OFF Not provided INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) ISOLATION INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) OUTPUT-FG AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (20±15C) OPEATING TEMP.,HUMID.AND ALTITUDE -0 to +100C (On aluminum base plate), 20-95%H (Non condensing) (efer to DEATING CUVE), 3,000m (10,000 feet) max ENVIONMENT STOAGE TEMP.,HUMID.AND ALTITUDE -0 to +100C, 20-95%H (Non condensing), 9,000m (30,000 feet) max VIBATION 10-55Hz, 9.0m/s 2 (5G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 196.1m/s 2 (20G), 11ms, once each along X, Y and Z axis SAFETY AND AGENCY APPOVALS UL , C-UL (CSA ), EN , EN50178 NOISE EGULATIONS HAMONIC ATTENUATO Complies with IEC (Class A) *3 CASE SIZE/WEIGHT 58.X12.7X37.3mm [2.3X0.5X1.7 inches] (WXHXD) / 80g max COOLING METHOD Conduction cooling (e.g. heat radiation from the aluminum base plate to the attached heat sink) *1 efer to instruction manual for measuring method of electric characteristics. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Please contact us about another class. -2

2 50F External view Base Plate (Aluminum) Lot No. ecommending size for processing PCB (TOP VIEW) Case (PBT) 58. max [2.3] (5.0) 8.3 ±0.5 [0.2] [1.9] 5.0 ± ±0.5 [0.2] 2-2 ± [0.3] [1.0] [0.3] 5-1 ± [0.05] AC1 AC2 Name Plate +BC -BC [0.3] [1.0] -VOUT TM +VOUT 27.9 ±0.5 [1.1] 37.3 max [1.7] (.7) [0.19] 2-M3 Mounting Hole [0.3] [0.3] 1.27 [0.05] 8.3 [1.9] 7.62 [0.3] mm Dimensions in : [inch] Div. : 0.2inch Tolerance : 0.3 [ 0.012] Weight : 80g max Dimensions in mm, [ ]=inches Mounting hole screwing torque : 0.9N m (5.0kgf cm) max -3

3 AC-DC Power Supplies Bus Converter. Power Module Type 100F Ordering information TUN S 100 F 05 -O * Providing heat sink as option 1 Series name 2 Single output 3 Output wattage Universal Input 5 Output voltage 6 Optional T : with Mounting hole (f3. thru) *Avoid short circuit between +BC and -BC. It may cause the failure of inside components. *Keep TM open, if output voltage adjustment is not necessary. *If remote sensing is not necessary, connect between +Vout & +S and between -Vout & -S. MODEL 100F05 100F12 100F2 MAX OUTPUT WATTAGE[W] DC OUTPUT 5V 20A 12V 8.A 2V.2A MODEL 100F05 100F12 100F2 AC f (Please refer to the instruction manual, 6.5 Derating) CUENT[A] ACIN 100V 1.3typ (Io=100%) ACIN 200V 0.7typ (Io=100%) FEQUENCY[Hz] 50/60 (7-63) ACIN 100V 82typ 83typ 8typ ACIN 200V 85typ 85typ 86typ POWE FACTO (Io=100%) ACIN 100V 0.95typ ACIN 200V 0.90typ INUSH CUENT Limited by external components (Thermistor) LEAKAGE CUENT[mA] 0.75max (ACIN 20V 60Hz, Io=100%, According to IEC ) CUENT[A] LINE EGULATION[mV] 10max 2max 8max LOAD EGULATION[mV] 10max 2max 8max 0 to +100C *1 80max 120max 120max IPPLE[mVp-p] -0 to 0C *1 120max 150max 150max 0 to 15% Load *1 160max 20max 20max OUTPUT 0 to +100C *1 120max 150max 150max IPPLE NOISE[mVp-p] -0 to 0C *1 200max 200max 250max 0 to 15% Load *1 20max 300max 300max TEMPEATUE EGULATION[mV] 0 to +65C 50max 120max 20max -0 to +100C 100max 20max 80max DIFT[mV] *2 20max 0max 90max OUTPUT VOLTAGE ADJUSTMENT ANGE[V] Fixed (TM pin open), adjustable by external resistor or external signal OUTPUT VOLTAGE SETTING[V] POTECTION CICUIT AND OVECUENT POTECTION Works over 105% of rating and recovers automatically OVEVOLTAGE POTECTION[V] EMOTE SENSING Provided EMOTE ON/OFF Not provided INPUT-OUTPUT AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) ISOLATION INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) OUTPUT-FG AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (20±15C) OPEATING TEMP.,HUMID.AND ALTITUDE -0 to +100C (On aluminum base plate), 20-95%H (Non condensing) (efer to DEATING CUVE), 3,000m (10,000 feet) max ENVIONMENT STOAGE TEMP.,HUMID.AND ALTITUDE -0 to +100C, 20-95%H (Non condensing), 9,000m (30,000 feet) max VIBATION 10-55Hz, 9.0m/s 2 (5G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 196.1m/s 2 (20G), 11ms, once each along X, Y and Z axis SAFETY AND AGENCY APPOVALS UL , C-UL (CSA ), EN , EN50178 NOISE EGULATIONS HAMONIC ATTENUATO Complies with IEC (Class A) *3 CASE SIZE/WEIGHT 58.X12.7X61.0mm [2.3X0.5X2. inches] (WXHXD) / 120g max COOLING METHOD Conduction cooling (e.g. heat radiation from the aluminum base plate to the attached heat sink) *1 efer to instruction manual for measuring method of electric characteristics. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Please contact us about another class. -

4 100F External view Base Plate (Aluminum) Lot No. 12.7±0.5 Case (PBT) 58. max [2.3] (5.0) 8.3 ±0.5 [0.2] [1.9] 5.0 ±0.5 [0.2] -M3 Mounting Hole 2-2 ±0.2 ecommending size for processing PCB (TOP VIEW) [0.3] [1.0] ±0.1 AC1 AC2 Name Plate +BC -BC [0.3] [1.0] -VOUT -S TM +S +VOUT ( 5.1 ) 50.8 ±0.5 [0.2] 61max [2.] [0.] [0.3] [0.3] [0.] [1.9] [0.3] [0.] [0.3] [0.2][0.2] [0.3] Dimensions in : Div. : 0.2inch mm [inch] Tolerance : 0.3 [ 0.012] Weight : 120g max Dimensions in mm, [ ]=inches Mounting hole screwing torque : 0.9N m (5.0kgf cm) max -5

5 AC-DC Power Supplies Bus Converter. Power Module Type 300F Ordering information TUN S 300 F 8 -O Series name 2 Single output 3 Output wattage Universal Input 5 Output voltage 6 Optional T : with Mounting hole (f3. thru) Y1: Outputvoltage adjustment range ±20% (Only 8V) 1: with emote ON/OFF 2: with emote ON/OFF (Low standby power) *Avoid short circuit between +BC/ and -BC. It may cause the failure of inside components. *Keep TM open, if output voltage adjustment is not necessary. *If remote sensing is not necessary, connect between +Vout & +S and between -Vout & -S. MODEL 300F12 300F28 300F8 MAX OUTPUT WATTAGE[W] DC OUTPUT 12V 25A 28V 11A 8V 6.5A MODEL 300F12 300F28 300F8 AC f CUENT[A] ACIN 100V 3.6typ (Io=100%) ACIN 200V 1.8typ (Io=100%) FEQUENCY[Hz] 50/60 (7-63) ACIN 100V 8typ 87typ 87typ ACIN 200V 86typ 89typ 90typ POWE FACTO (Io=100%) ACIN 100V 0.96typ ACIN 200V 0.93typ INUSH CUENT Limited by external resistance LEAKAGE CUENT[mA] 0.75max (ACIN 20V 60Hz, Io=100%, According to IEC ) CUENT[A] LINE EGULATION[mV] 2max 56max 96max LOAD EGULATION[mV] 2max 56max 96max IPPLE[mVp-p] 0 to +100C *1 120max 180max 250max -0 to 0C *1 150max 200max 300max OUTPUT IPPLE NOISE[mVp-p] 0 to +100C *1 150max 200max 300max -0 to 0C *1 200max 300max 50max TEMPEATUE EGULATION[mV] 0 to +65C 120max 280max 80max -0 to +100C 20max 560max 960max DIFT[mV] *2 0max 90max 180max OUTPUT VOLTAGE ADJUSTMENT ANGE[V] Fixed (TM pin open), adjustable by external resistor or external signal (-Y1 Option : ) OUTPUT VOLTAGE SETTING[V] POTECTION CICUIT AND OVECUENT POTECTION Works over 105% of rating and recovers automatically OVEVOLTAGE POTECTION[V] (-Y1 Option : ) EMOTE SENSING Provided EMOTE ON/OFF Optional (External power supply is required) INPUT-OUTPUT-C * AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) ISOLATION INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) OUTPUT-C-FG * AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (20±15C) OUTPUT-C * AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (20±15C) OPEATING TEMP.,HUMID.AND ALTITUDE -0 to +100C (On aluminum base plate), 20-95%H (Non condensing) (efer to DEATING CUVE), 3,000m (10,000 feet) max ENVIONMENT STOAGE TEMP.,HUMID.AND ALTITUDE -0 to +100C, 20-95%H (Non condensing), 9,000m (30,000 feet) max VIBATION 10-55Hz, 9.0m/s 2 (5G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 196.1m/s 2 (20G), 11ms, once each along X, Y and Z axis SAFETY AND AGENCY APPOVALS UL , C-UL (CSA ), EN NOISE EGULATIONS HAMONIC ATTENUATO Complies with IEC (Class A) *3 CASE SIZE/WEIGHT 117.3X12.7X61.5mm [.62X0.5X2.2 inches] (WXHXD) / 190g max COOLING METHOD Conduction cooling (e.g. heat radiation from the aluminum base plate to the attached heat sink) *1 efer to instruction manual for measuring method of electric characteristics. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Please contact us about another class. * C is applicable when remote control (optional) is added. -6

6 300F External view Case (PBT) Base Plate (Aluminum) [0.] 10 [0.39] (5.3) Name Plate max [.62] ±0.5 [.2] Lot No ± Control pin for emote ON/OFF (Option) 5.0 ± ±0.5 [0.2] 2-2 ± ± max [2.2] 3 = [0.7] [0.35] [0.39] (5.35) [0.] -M3 Mounting Hole ecommending size for processing PCB (TOP VIEW) [.2] =12 [0.] [0.39] [0.35] [0.7] 50.8 Tolerance : 0.3 [ 0.012] Weight : 190g max Dimensions in mm, [ ]=inches Mounting hole screwing torque : 0.9N m (5.0kgf cm) max mm Dimensions in : [inch] Div. : 0.5inch AC1 -VOUT AC2 +BC -BC C2 (Option) C1 (Option) +VOUT -S +S TM IOG -FG -7

7 AC-DC Power Supplies Bus Converter. Power Module Type 500F Ordering information TUN S 500 F 8 -O Series name 2 Single output 3 Output wattage Universal Input 5 Output voltage 6 Optional T : with Mounting hole (f3. thru) Y1: Outputvoltage adjustment range ±20% (Only 8V) 1: with emote ON/OFF 2: with emote ON/OFF (Low standby power) *Avoid short circuit between +BC/ and -BC. It may cause the failure of inside components. *Keep TM open, if output voltage adjustment is not necessary. *If remote sensing is not necessary, connect between +Vout & +S and between -Vout & -S. MODEL 500F12 500F28 500F8 MAX OUTPUT WATTAGE[W] DC OUTPUT 12V 2A (Peak 55A) 28V 18A (Peak 2A) 8V 10.5A (Peak 1A) MODEL 500F12 500F28 500F8 AC f CUENT[A] ACIN 100V 6.0typ (Io=100%) ACIN 200V 3.0typ (Io=100%) FEQUENCY[Hz] 50/60 (7-63) ACIN 100V 8typ 87typ 88typ ACIN 200V 86typ 90typ 90.5typ POWE FACTO (Io=100%) ACIN 100V 0.96typ ACIN 200V 0.93typ INUSH CUENT Limited by external resistance LEAKAGE CUENT[mA] 0.75max (ACIN 20V 60Hz, Io=100%, According to IEC ) CUENT[A] *3 2 (Peak 55) 18 (Peak 2) 10.5 (Peak 1) LINE EGULATION[mV] 2max 56max 96max LOAD EGULATION[mV] 2max 56max 96max IPPLE[mVp-p] 0 to +100C *1 120max 180max 250max -0 to 0C *1 150max 200max 300max OUTPUT IPPLE NOISE[mVp-p] 0 to +100C *1 150max 200max 300max -0 to 0C *1 200max 300max 50max TEMPEATUE EGULATION[mV] 0 to +65C 120max 280max 80max -0 to +100C 20max 560max 960max DIFT[mV] *2 0max 90max 180max OUTPUT VOLTAGE ADJUSTMENT ANGE[V] Fixed (TM pin open), adjustable by external resistor or external signal (-Y1 Option : ) OUTPUT VOLTAGE SETTING[V] POTECTION CICUIT AND -8 OVECUENT POTECTION Works over 101% of peak current and recovers automatically OVEVOLTAGE POTECTION[V] (-Y1 Option : ) EMOTE SENSING Provided EMOTE ON/OFF Optional (External power supply is required) INPUT-OUTPUT-C *5 AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) ISOLATION INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) OUTPUT-C-FG *5 AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (20±15C) OUTPUT-C *5 AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (20±15C) OPEATING TEMP.,HUMID.AND ALTITUDE -0 to +100C (On aluminum base plate), 20-95%H (Non condensing) (efer to DEATING CUVE), 3,000m (10,000 feet) max ENVIONMENT STOAGE TEMP.,HUMID.AND ALTITUDE -0 to +100C, 20-95%H (Non condensing), 9,000m (30,000 feet) max VIBATION 10-55Hz, 9.0m/s 2 (5G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 196.1m/s 2 (20G), 11ms, once each along X, Y and Z axis SAFETY AND AGENCY APPOVALS UL , C-UL (CSA ), EN NOISE EGULATIONS HAMONIC ATTENUATO Complies with IEC (Class A) * CASE SIZE/WEIGHT 117.3X12.7X61.5mm [.62X0.5X2.2 inches] (WXHXD) / 190g max COOLING METHOD Conduction cooling (e.g. heat radiation from the aluminum base plate to the attached heat sink) *1 efer to instruction manual for measuring method of electric characteristics. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 ( ) means peak current. Avoid operating with peak current continuously. It may cause failure of the components inside the product. There are limitation of available condition of the peak current, such as peak time, duty etc. (efer to the instruction manual in detail.) * Please contact us about another class. *5 C is applicable when remote control (optional) is added.

8 500F External view Case (PBT) Base Plate (Aluminum) [0.] 10 [0.39] (5.3) Name Plate max [.62] ±0.5 [.2] Lot No ± Control pin for emote ON/OFF (Option) 5.0 ± ±0.5 [0.2] 2-2 ± ± max [2.2] 3 = [0.7] [0.35] [0.39] (5.35) [0.] -M3 Mounting Hole ecommending size for processing PCB (TOP VIEW) [.2] =12 [0.] [0.39] [0.35] [0.7] 50.8 Tolerance : 0.3 [ 0.012] Weight : 190g max Dimensions in mm, [ ]=inches Mounting hole screwing torque : 0.9N m (5.0kgf cm) max mm Dimensions in : [inch] Div. : 0.5inch AC1 -VOUT AC2 +BC -BC C2 (Option) C1 (Option) +VOUT -S +S TM IOG -FG -9

AC-DC Power Supplies Bus Converter. Power Module Type 700F Ordering information TUN S 700 F 8 -O 1 2 3 5 6-10 *Avoid short circuit between +BC/ and -BC. It may cause the failure of inside components.

1 Series name 2 Single output 3 Output wattage Universal Input 5 Output voltage 6 Optional T : with Mounting hole (f3.

9 AC-DC Power Supplies Bus Converter. Power Module Type 700F Ordering information TUN S 700 F 8 -O *Avoid short circuit between +BC/ and -BC. It may cause the failure of inside components. *Keep TM open, if output voltage adjustment is not necessary. *If remote sensing is not necessary, connect between +Vout & +S and between -Vout & -S. 1 Series name 2 Single output 3 Output wattage Universal Input 5 Output voltage 6 Optional T : with Mounting hole (f3. thru) Y1: Outputvoltage adjustment range ±20% (Only 8V) 1: with emote ON/OFF 2: with emote ON/OFF (Low standby power) P : Parallel operation (Output voltage variable, emote sensing disabled) MODEL 700F12 700F28 700F8 MAX OUTPUT WATTAGE[W] DC OUTPUT 12V 58.A 28V 25A 8V 1.6A MODEL 700F12 700F28 700F8 AC f CUENT[A] ACIN 100V 8.6typ (Io=100%) ACIN 200V.1typ (Io=100%) FEQUENCY[Hz] 50/60 (7-63) ACIN 100V 83typ 86typ 87typ ACIN 200V 86typ 89typ 90typ POWE FACTO ACIN 100V 0.96typ (Io=100%) ACIN 200V 0.93typ INUSH CUENT Limited by external resistance LEAKAGE CUENT[mA] 0.75max (ACIN 20V 60Hz, Io=100%, According to IEC ) CUENT[A] LINE EGULATION[mV] 2max 56max 96max LOAD EGULATION[mV] 2max 56max 96max IPPLE[mVp-p] 0 to +100C *1 120max 180max 250max -0 to 0C *1 150max 200max 300max OUTPUT IPPLE NOISE[mVp-p] 0 to +100C *1 150max 200max 300max -0 to 0C *1 200max 300max 50max TEMPEATUE EGULATION[mV] 0 to +65C 120max 280max 80max -0 to +100C 20max 560max 960max DIFT[mV] *2 0max 90max 180max OUTPUT VOLTAGE ADJUSTMENT Fixed (TM pin open), adjustable by external resistor or external signal ANGE[V] (-Y1 Option : ) OUTPUT VOLTAGE SETTING[V] POTECTION CICUIT AND OVECUENT POTECTION Works over 105% of rating and recovers automatically OVEVOLTAGE POTECTION[V] (-Y1 Option : ) EMOTE SENSING Provided EMOTE ON/OFF Optional (External power supply is required) MODEL 700F12-P 700F28-P 700F8-P MAX OUTPUT WATTAGE[W] DC OUTPUT 12V 58.A 28V 25A 8V 1.6A MODEL 700F12-P 700F28-P 700F8-P AC f CUENT[A] ACIN 100V 8.6typ (Io=100%) ACIN 200V.1typ (Io=100%) FEQUENCY[Hz] 50/60 (7-63) ACIN 100V 83typ 86typ 87typ ACIN 200V 86typ 89typ 90typ POWE FACTO ACIN 100V 0.96typ (Io=100%) ACIN 200V 0.93typ INUSH CUENT Limited by external resistance LEAKAGE CUENT[mA] 0.75max (ACIN 20V 60Hz, Io=100%, According to IEC ) CUENT[A] VOLTAGE ACCUACY[%] +5, -3 +5, -3 +5, -3 0 to +100C *1 20max 360max 600max OUTPUT IPPLE[mVp-p] -0 to 0C *1 300max 00max 700max 0 to +30% Load *1 360max 50max 900max 0 to +100C *1 300max 00max 700max IPPLE NOISE[mVp-p] -0 to 0C *1 00max 600max 1000max 0 to +30% Load *1 50max 600max 1000max POTECTION CICUIT AND OVECUENT POTECTION Works over 105% of rating and recovers automatically OVEVOLTAGE POTECTION[V] EMOTE ON/OFF Optional (External power supply is required)

10 GENEAL 700F INPUT-OUTPUT-C * AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) ISOLATION INPUT-FG AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (20±15C) OUTPUT-C-FG * AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (20±15C) OUTPUT-C * AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (20±15C) OPEATING TEMP.,HUMID.AND ALTITUDE -0 to +100C (On aluminum base plate), 20-95%H (Non condensing) (efer to DEATING CUVE), 3,000m (10,000 feet) max ENVIONMENT STOAGE TEMP.,HUMID.AND ALTITUDE -0 to +100C, 20-95%H (Non condensing), 9,000m (30,000 feet) max VIBATION 10-55Hz, 9.0m/s 2 (5G), 3minutes period, 60minutes each along X, Y and Z axis IMPACT 196.1m/s 2 (20G), 11ms, once each along X, Y and Z axis SAFETY AND AGENCY APPOVALS UL , C-UL (CSA ), EN NOISE EGULATIONS HAMONIC ATTENUATO Complies with IEC (Class A) *3 CASE SIZE/WEIGHT 117.3X12.7X61.5mm [.62X0.5X2.2 inches] (WXHXD) / 190g max COOLING METHOD Conduction cooling (e.g. heat radiation from the aluminum base plate to the attached heat sink) *1 efer to instruction manual for measuring method of electric characteristics. *2 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. *3 Please contact us about another class. * C is applicable when remote control (optional) is added. External view Case (PBT) Base Plate (Aluminum) [0.] 10 [0.39] (5.3) Name Plate max [.62] ±0.5 [.2] Lot No ± Control pin for emote ON/OFF (Option) 5.0 ± ±0.5 [0.2] 2-2 ± ± max [2.2] 3 = [0.7] [0.35] [0.39] (5.35) [0.] -M3 Mounting Hole ecommending size for processing PCB (TOP VIEW) [.2] =12 [0.] [0.39] [0.35] [0.7] 50.8 Tolerance : 0.3 [ 0.012] Weight : 190g max Dimensions in mm, [ ]=inches Mounting hole screwing torque : 0.9N m (5.0kgf cm) max mm Dimensions in : [inch] Div. : 0.5inch AC1 AC2 +BC -BC C2 (Option : 1/2) C1 (Option : 1/2) -VOUT +VOUT -S, -M (Option : P) +S, +M (Option : P) TM, NC (Option : P) IOG -FG -11

MODEL LEP100F-24 LEP100F-36 LEP100F-48 DC OUTPUT +24V 4.2(Peak 7)A +36V 2.8(Peak 4.7)A +48V 2.1(Peak 3.5)A

MODEL LEP100F-24 LEP100F-36 LEP100F-48 DC OUTPUT +24V 4.2(Peak 7)A +36V 2.8(Peak 4.7)A +48V 2.1(Peak 3.5)A AC-DC Power Supplies Open Frame/ Enclosed type 00F Ordering information 00 F -2 -O 2 3 R Recommended EMI/EMC Filter NAC-06-72 High voltage pulse noise type : NAP series Low leakage current type : NAM series