10 AMP POWER RELAY. Breakdown voltage* 2. Operate time* 3 (at nominal voltage) Shock resistance. Vibration resistance. Unit weight

Transcription

1 VDE 2c, 3c AMP POWER RELAY RELAYS FEATURES Interchangeable with existing models Long life and high reliability High contact capacity up to A 20 Available with plug-in/solder and quick-connect terminals SPECIFICATIONS (at 20 C 68 F) Contacts Arrangement 4 Form C Initial contact resistance, max. 1 mω (By voltage drop 6 1 A) Silver Contact material Silver alloy switching A 20 (resistive) Rating capacity Min. switching capacity #1 0, #1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. Remarks * Specifications will vary with foreign standards certification ratings. * 1 Measurement at same location as initial breakdown voltage section * 2 Detection current; * 3 Excluding contact bounce time * 4 Half-wave pulse of sine wave: 11ms; detection time: µs * Half-wave pulse of sine wave: 6ms * 6 Detection time: µs * 7 Refer to 6. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT Characteristics (at 60 Hz, 20 C 68 F) 4 Form C Maximum speed 20 cpm Initial insulation resistance* 1 more than 0 MΩ at 00 Breakdown voltage* 2 Between open contacts Between contact sets Between contact and coil Operate time* 3 (at nominal voltage) Release time (without diode)* 3 (at nominal voltage) 1,000 1,00 1,00 2 ms 2 ms 2,000 2,000 2,000 1,000 1,00 1,00 30 ms 30 ms Temperature rise 6 C Shock resistance Functional* 4 98 m/s 2 { G} Destructive* 980 m/s 2 {0 G} Vibration resistance Functional* 6 to Hz at 1 mm double amplitude Destructive to Hz at 2 mm double amplitude Conditions for operation, transport and storage* 7 (Not freezing and condensing at low temperature) Unit weight Ambient temp. Humidity Approx. 60g 2.12 oz 0 C to +40 C 8 F to +4 F to 8% R.H. Approx. 0g 3.3 oz Approx. 12g 4.41 oz LIFE DATA Contact rating and expected life For AC load type Electrical life Voltage Expected life Load Resistive (cos ϕ ] 1) Inductive (cos ϕ ] 0.4) Resistive (cos ϕ ] 1) Inductive (cos ϕ ] 0.4) (min. operations) Current A 7. A 2 A 7. A 7. A A A 3 A 3 A 2 A 1 6 1A 0.7 A 0.6 A 0.4 A 2 6 Mechanical life 1 7 Note: When the electromagnet or exciting coil (Solenoid, etc.) is the load, the value of motor or lamp load is applicable.

2 Contact rating and expected life For DC load type Electrical life Life curve Operations, 4 1, Voltage Expected life Load Resistive (cos ϕ ] 1) Inductive (cos ϕ ] 0.4) Resistive (cosϕ ] 1) Inductive (cos ϕ ] 0.4) (min. operations) Current Mechanical life more than,000,000 operations 12 cosϕ = 1 cosϕ = 1 Load A 7 A 2 7. A A 0. A 0.4 A A 3 A 0.3 A 0.2 A 1 6 1A 0.6 A 0.1 A 0.06 A 2 6 Mechanical life 1 7 Notes: 1. For DC inductive loads, use an arc suppressing circuit. 2. When used under a DC load at high repetition rate with considerable arcing, corrosion of the contacts and/or the contact blades is likely to occur. When using the relay under conditions of high temperature, humidity or high repetition rate, it is suggested that the relay cover be removed to facilitate extended operation. TYPICAL APPLICATIONS relays enjoy wide use in various applications, particularly in automation controls and remote controls. Applications include: Industrial machinery ORDERING INFORMATION Ex. 3 Machine tool Food processing packing machines Office equipment Coin operate devices Home appliances M AC240V Transportation Communication and measuring devices Amusement devices Contact arrangement 2: 3: 4: 4 Form C TYPES AND COIL DATA 1. Standard plug-in terminal type (without lamp wired) DC TYPES at 20 C 68 F 4 Form C Terminal Nil: Standard plug-in terminal M: Direct mounting ( only) TM: Top mounting ( only) L: Lamp wired, standard plug-in terminal (Notes) 1. For UL/CSA or VDE recognized types, add suffix UL/CSA or VDE (2-TM type VDE application under way) 2. Standard packing Carton: 0 pcs. Case: 200 pcs. 3. UL/CSA approved type is standard. (max.) (min.) Coil voltage AC 6, 12, 24, 48, 11, 220, 240 V DC 6, 12, 24, 48, 1 V Coil resistance, Ω (±%) W 2-DC6V DC12V DC24V DC48V , DC1V , DC6V DC12V DC24V DC48V , DC1V , DC6V DC12V DC24V DC48V , DC1V ,

3 AC TYPE (0/60 Hz) at 60 Hz, 20 C 68 F 4 Form C NOTES 1. The range of coil current for AC relays is ±1% (60 Hz). For DC relays it is ±% at 20 C, 68 F. 2. The relay will operate in a range from 80% to 1% of the nominal coil voltage. It is, however, recommended that the relay be used in the range of 8% to 1% of the nominal coil with the temporary voltage variation taken into consideration. (max.) (min.) Inductance, H VA 2-AC6V AC12V AC24V AC48V AC11V AC220V AC240V AC6V AC12V AC24V AC48V AC11V AC220V AC240V AC6V AC12V AC24V AC48V AC11V AC220V AC240V When the voltage of AC relays drops below 80% of the nominal coil the relay will generate a considerable amount of heat which is not recommended for maximum efficiency. 4. The coil resistance of DC types is the measured value of the coil at a temperature of 20 C 68 F. If the coil temperature changes by ±1 C, the measured value of the coil resistance should be increased or decreased by 0.4%.. For applications from 220 V to 240 V DC, connect a resistor in series with the relay coil. See chart for resistor values. Voltage 4 Form C kω ( W) 8.7 kω ( W) 7.4 kω ( W) 8.8 kω ( W) 7 kω ( W) 8.3 kω ( W) 2. Standard plug-in terminal type (with lamp wired) DC TYPES at 20 C 68 F 4 Form C (max.) (min.) Coil resistance, Ω (±%) W 2-L-DC6V L-DC12V L-DC24V L-DC48V , Neon lamp 2-L-DC1V , L-DC6V L-DC12V L-DC24V L-DC48V , Neon lamp 3-L-DC1V , L-DC6V L-DC12V L-DC24V L-DC48V , Neon lamp 4-L-DC1V ,

4 AC TYPE (0/60 Hz) at 60 Hz, 20 C 68 F 4 Form C Neon lamp Neon lamp Neon lamp 3. Top Mounting (TM) and direct mounting (M) type DC TYPES at 20 C 68 F Top Mounting (TM) Direct Mounting (TM) AC TYPE (0/60 Hz) at 60 Hz, 20 C 68 F Top Mounting (TM) Direct Mounting (M) (max.) (min.) Inductance, H VA 2-L-AC6V L-AC12V L-AC24V L-AC11V L-AC220V L-AC240V L-AC6V L-AC12V L-AC24V L-AC11V L-AC220V L-AC240V L-AC6V L-AC12V L-AC24V L-AC11V L-AC220V L-AC240V (max.) (min.) Coil resistance, Ω (±%) W 2-TM-DC6V TM-DC12V TM-DC24V TM-DC48V , TM-DC1V , M-DC6V M-DC12V M-DC24V M-DC48V $B!"(J M-DC1V , (max.) (min.) Inductance, H VA 2-TM-AC6V TM-AC12V TM-AC24V TM-AC48V TM-AC11V TM-AC220V TM-AC240V M-AC6V M-AC12V M-AC24V M-AC48V M-AC11V M-AC220V M-AC240V

5 4. Direct mounting (with lamp wired) type DC TYPES AC TYPE (0/60 Hz) at 60 Hz, 20 C 68 F LAMP-WIRED RELAYS (max.) (min.) Coil resistance, Ω (±%) Neon lamp 3-ML-DC1V , Neon lamp (max.) (min.) Inductance, H W VA 3-ML-AC11V 11 V ML-AC220V 220 V ML-AC240V 240 V Specifications Life of neon lamp...continuous: more than 2,000 hours (more than 3 years) on/off = 1: more than 6 years Life of...continuous: more than 0,000 hours (more than. years) on/off = 1: more than 0,000 hours (more than 11 years) NEON LAMP Variation 2-L 3-L 3-ML 4-L Notes: 1. AC 48 V type is not available for lamp wiring. Coil Voltage AC DC 6 V 6 V 12 V 12 V 24 V 24 V 48 V 11 V 1 V 220 V 240 V (Light emitting diode) Neon lamp Circuit diagrams Neon lamp type type Terminal No. (DC type) 3-L 2-L Polarity 3-ML 4-L ( + ) 7 ( ) Operating current of Coil Voltage Operating current of DC 6V DC 6.4 DC 12V DC.7 DC 24V DC 4.7 DC 48V DC 4. AC 6V AC. AC 12V AC 9.0 AC 24V AC 7.7 Notes: 1. Operating current of relays should be increased by the value of current. Please refer the table. Operating current of neon lamp is approx. 0.3 to To use the relay in the inductive load circuit, the contact protection circuit is recommended. Notes: 1. Pay attention to the polarity of coil See circuit diagram ( type only).

6 ACCESSORIES Please refer to MOUNTING METHODS for further information. UL, CSA recognized except BRACKET and INSERTING PLATE. Relay Solder terminal socket for rectangular hold boring (with hold-down clip) Screw terminal socket for DIN rail assembly (with hold-down clip) For 2, 4 2-SRS 2-SFD -BRACKET for direct mounting 2 (UL, CSA, VDE) (UL, CSA) 3-SRS 3-SFD 3 INSERTION PLATE for P/C board mounting (UL, CSA, VDE) 4-SRS (UL, CSA) 4-SFD 4 (UL, CSA) (UL, CSA) DIMENSIONS AND WIRING DIAGRAM 2 () Plug-in terminal types Circuit diagram Accepts Faston to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ±.09

7 2-SRS (with hold-down clip) Optimum space-saving panel cut-out. Can be mounted from either the front or the rear of the panel. Front surface-mounting.16±.004 DIA. HOLE HOLD-DOWN CLIP RELAY ± ± to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ± ± ± Rear surface-mounting ±.004 DIA. HOLE 39 48± ± 2± ± ± ± SOCKET 4 mm SCREW SPRING WASHER HOLD-DOWN CLIP RELAY SOCKET 4 mm SCREW SPRING WASHER 2-SFD (with hold-down clip) Front wiring in restricted space ±0.2 ± RELAY HOLD DOWN CLIP 23.8 ± ±.024 Mounting dimensions 12 2-M4.17 SCREW HOLE or 22 ± ± ± ±.008 ± ±.004 DIA. HOLE.8 ± ± ± ± ± ± ± ± ± ± ±1 ± ± ±0.3.2 ±.012 ± ±0. 1 ± 80 ±1 3. ± ± ± 3. 1 ± ± ± ± ± ± to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ± ±0.6 ± ± ± ± ±.024 Installation screw block (installation screw, hexagonal nut, spring washer) Panel hole dimensions for side-by-side installation Note: Hold down clip and installation screw block are included in package. 2-TM () Top mounting types mm SCREW or 8-32 NC-2 SCREW SCREW WASHER Circuit diagram Mounting dimensions Accepts Faston R.089R to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ±.09 4.±0.1 DIA. HOLE or.117±.004 DIA. HOLE

8 3 () Plug-in terminal types Accepts Faston Circuit diagram 2 to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ±.09 3-SRS (with hold-down clip) Optimum space-saving panel cut-out. Can be mounted from either the front or the rear of the panel. Front surface-mounting.16±.004 DIA. HOLE ± ± ± ± 2 ± ±.012 HOLD DOWN CLIP RELAY Lot No dia. 0 dia Rear surface-mounting.16±.004 DIA. HOLE to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ± ± ± 3-SFD (with hold-down clip) Front wiring in restricted space 22 ± ± RELAY HOLD DOWN CLIP 23.8 ± ±.024 Mounting dimensions 2-M4.17 SCREW HOLE or ± ± ± ±0.2 DIA. HOLE 1.47 ± ±.008. ± ± ± ± ± ± ± ± ±1 ± ±.039 ± ±1 3. ± ±0. 1 ± 69 ± ± ± ± ±0.3.2 ± ± ± ±.012 ± ±0.6 ± ± ± ± ± Note: Hold down clip and installation screw block are included in package. Installation screw block (installation screw, hexagonal nut, spring washer) Panel hole dimensions for side-by-side installation 2 to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ±.09

9 3-M () Direct mounting types R Mounting dimension Accepts Faston R Circuit diagram 2 to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ±.09.16±.004 DIA. HOLE MIN MIN mm SCREW or 8-32 NC-2 SCREW SPRING WASHER (4 Form C) Plug-in terminal types Circuit diagram Accepts Faston to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ±.09

10 4-SRS (with hold-down clip) Optimum space-saving panel cut-out. Can be mounted from either the front or the rear of the panel. Front surface-mounting.16±.004 DIA. HOLE HOLD-DOWN CLIP RELAY ± ± ± ± Rear surface-mounting.16±.004 DIA. HOLE 2± ± SOCKET 4 mm SCREW SPRING WASHER HOLD-DOWN CLIP RELAY 2 to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ± ± ± 3± ± SOCKET 4 mm SCREW SPRING WASHER 4-SFD (with hold-down clip) Front wiring in restricted space. Two 2 relays can be mounted in one socket. ±0.2 2 ±0.1 ±.004 ±.008 ±0.2 ±.008 HOLD DOWN CLIP 4 RELAY 23.8 ± ±.024 Mounting dimensions 2-M4.17 SCREW HOLE or ± ±.004 DIA. HOLE 3 ± ± ± ± ± ± ± ± ± ± ± ± ± ±.039 ±1 ± ±1 3. ± ±0. 1 ± 69 ± ± ± ± ±0.2 1 ± ± ± ± ±0.3.2 ± ± ± ±.012 ±0.6 ± ± ± ± ± Installation screw block (installation screw, hexagonal nut, spring washer) Panel hole dimensions for side-by-side installation Note: Hold down clip and installation screw block are included in package. 2 to 9mm.079 to.34 inch: ±0. ± 9 to 20mm.34 to.787 inch: ±1.0 ±.039 Min. 20mm.787 inch: ±1. ±.09 ACCESSORIES for 2 and 4 types Bracket (with 2 screws, 2 washers) The Bracket is used for mounting 2 relays and 4 relays directly to the panel. It facilitates soldering or quick connections with Faston 20 tab 0.8 mm.031 inch. Notes: 1. This bracket is unavailable for UL, CSA and VDE applications. 2. When using the special bracket, it is recommended to use the screws and washers called out in the chart in the next page in order to eliminate any possible damage to the relay coil. Mounting methods (a) Remove the M3 7 screw (red colored) fixed to the relay, and place the bracket on the relay with the attaching M3 7 screw (blue colored) and the spring washer. Keying tab. (b) Use the additional M3 7 screw and washer for attaching the bracket to the panel. For the 4 type relay two brackets are used ± DIA. HOLE.1 DIA. HOLE DIA. HOLE.118 DIA. HOLE

11 Thickness of a special bracket 1.0 mm (.039 inch) 1.6 mm (.063 inch) 2.0 mm (.079 inch) A suitable screw M3 7-M3 8 M3 8 M3 8-M3 A suitable washer for M3 for M3 for M3 Screw M 3 7 Millimeter 3mm.118inch diameter 7mm.276inch length Dimensions and mounting method 1. Rear-surface mounting 2. Front-surface mounting 4. DIA. HOLE.177 DIA. HOLE MIN DIA. HOLE.126 DIA. HOLE DIA. HOLE.177 DIA. HOLE DIA. HOLE.126 DIA. HOLE MIN mm SCREW BRACKET KEYING TAB 27 3 mm SCREW mm SCREW MIN DIA. HOLE.177 DIA. HOLE DIA. HOLE.177 DIA. HOLE MIN mm SCREW KEYING TAB BRACKET Inserting Plate for 2 and 4 types 1. inserting plate is used for mounting 2 and 4 relays on a printed board to adjust the length of the terminals. 2. If adjustment by soldering is not suitable, bore 1/8" diameter hole on the printed circuit board and mount the relay with a M3 screw. The chart to the right suggests the proper screws for different printed circuit boards. 3. Two plates are used for the 4 type relay. Thickness of P/C board Suitable screw 1.0 mm.039 inch M3 1.2 mm.047 inch M3 PC board pattern DIA. HOLE.17 DIA. HOLE DIA. HOLE.126 DIA. HOLE DIA. HOLE.126 DIA. HOLE INSERTION PLATE PC BOARD Please refer to the above second instruction. Tolerance: ±0.1 ±.004 For Cautions for Use, see Relay Technical Information