Temperature controller. Side. Vac 3. Typically. Temperature controller. Side. Vac Driving SSR. Temperature controller. Resistor. Vac.
|
|
- Shannon Underwood
- 5 years ago
- Views:
Transcription
1 Solid State Relays Vdc Input/ Output, Input/ Output High Reliability Shown smaller than actual size ac Controlled used with Controller with dc Voltage Driver Output L Typically ac Controlled used with Controller with Mechanical Relay Output Model DC5 Shown with Current Ratings to 9 Amps Multi-Million Cycle Life Compatible with Controllers Solid-State, SCR Design Zero Voltage Switching Control ac Lines to ac and dc Control Signal Models % Testing at Rated Current These s control resistance heaters up to kw using solid state relays in conjunction with lower rated temperature s. Solid state relays are SPST, normally open switching devices with no moving parts, capable of millions of cycles of operation. By applying a control signal, an switches ON the ac load current, just as the moving contacts do on a mechanical contactor. Three-phase loads can be controlled using or s. Use s for Y or star -phase loads using a neutral line. Two s will control delta loads with no neutral line. Three solid state relays are also used when there is no neutral load to provide redundancy and extra assurance of control. Switching takes place at the zero voltage crossover point of the alternating current cycle. Because of this, no appreciable electrical noise is generated, making s ideal for environments where there are apparatuses susceptible to RFI. Driving S SR ac Controlled used with Controller with Triac Output Resistor Driving Typical Applications Operating : - to 8 C (-5 to 75 F) Storage : - to 8 C (- to 75 F) Isolation: Vrms, input to output; 5 Vrms input/output to ground Capacitance: 8 pf, input to output (max) Line Frequency Range: 7 to 6 Hz Turn-On Time: ms, ac; 5 cycle, dc ms, ac; 5 cycle, dc for and Vdc Input Models Speci cations Max On State Current Min On State Current Max -Cycle Surge Max sec Surge T (6 Hz), A sec P-57 Amp 5 Amp 5 Amp 5 Amp 75 Amp A 5 A 5 A 5 A 75 A ma A 5 A 5 A 5 A 7 A A 75 A 5 A 5 A A Amp 9 A A 8 A 75
2 Solid State Relays These s are of the twin SCR type, inherently more reliable and capable of higher overloads before failure than triacs. Heat is developed in a solid state relay due to the nominal voltage drop across the switching device. To dissipate the heat, an must be mounted on a finned heat sink or aluminum plate. An should be located where the ambient temperature is relatively low, since the current switching rating is lowered as the temperature increases. Another characteristic is a small leakage current across the output when the relay is open. Because of this, a voltage will always exist on the load side of the device. In comparing s with mechanical contactors, the has a cycle life many times that of a comparably priced contactor. However, s are more prone to failure due to overload and improper initial wiring. Solid state relays can fail, contact closed, on overload circuits. Finned heat sinks are anodized fabrications that come complete with tapped mounting holes and screws. See thermal rating curves and ordering instructions for proper selection. baseplate to heat sink thermal resistance is affected by use of a thermally conducting compound. OMEGATHERM OT- placed between the heat sink and baseplate will significantly improve the thermal conductivity. It is also suggested that -inch-pounds of torque be used on the mounting screws. FHS Heat Sink Dimensions and Specifications and Heat Sink Dimensions (.) (.578) A B C Thermal Rating.".5".56" C/W 5.5" 5.".8". C/W MOUNTING HOLES () 8- THDS. (.6) (.) Heat Sink Dimensions C L (.67) (.6) (.5) (.75) C (.875) (5.5). (.5) C L A B 8- TH'D Places Dimensions shown in mm (in).5 (.56) CENTERS #6 (SCREWS) (.75) (.5) R Series Electrical Specifications (.) END VIEW P-58 (.8) (.) (.87) (.8) (TYP) (TYP.) TOP VIEW Dimensions shown in mm (in) Input-Control Signal Input & Output Control Control Control Signal Peak Signal Signal Signal Input Repetitive Type Voltage Turn-On Turn-OffImpedance Voltage Min. AC AC5 ac AC5 Control 9 to 8 9 k 5 V AC75 Signal AC9 DC DC5 dc DC5 Control to Vdc Vdc Vdc k 5 V DC75 Signal DC9 AC5 ac AC75 Control 9 to 8 9 k V AC9 Signal DC5 dc DC75 Control to Vdc Vdc Vdc k V DC9 Signal For Additional Controllers and Indicators, See Section M P
3 Derate current 5% for Derate current 5% for Derate current 5% for A MODELS A MODELS 5 A MODELS DERATE CURRENT % FOR HORIZONTAL FIN MOUNT 5 5 A MODELS FFH DERATE CURRENT % FOR HORIZONTAL FIN MOUNT A MODELS ( C) ( C).5 (.75) 7.9 (.) \ 8- Thread DERATE CURRENT % FOR HORIZONTAL FIN MOUNT 9 A MODELS (.87). (.7) 9.5 (.95) 57. (.5) Tolerances XX -. XXX -..5 (.) Clearance For Circuit Board Mounting. (.87) (.7) Two Places 5. (.) 6- Thread ( C) Series Output-V ac Line Load Max. Contact (5 C max. ambient) Dissipation Voltage Current Voltage Drop Watt/Amps AC A 7.5 ma 5 ma.6 AC5 5 A 7.5 ma 5 ma. AC5 to 8 5 A.6 V 7.5 ma 5 ma N/A.9 AC75 75 A 7.5 ma 5 ma * AC9 9 A 7.5 ma 5 ma * DC A 7.5 ma 5 ma.6 DC5 5 A 7.5 ma 5 ma. DC5 to 8 5 A.6 V 7.5 ma 5 ma N/A.9 DC75 75 A 7.5 ma 5 ma * DC9 9 A 7.5 ma 5 ma * AC5 5 A ma 8 ma 5 ma * AC75 6 to 8 75 A.6 V ma 8 ma 5 ma * AC9 9 A ma 8 ma 5 ma * DC5 5 A ma 8 ma 5 ma * DC75 6 to 8 75 A.6 V ma 8 ma 5 A m * DC9 9 A ma 8 ma 5 ma * Transients of min. max duration above table value should be suppressed. P-59
4 Solid State Relays /.67 /.67 /.67 /6.7 5 /.67 /.67 /.67 /6.7 IN STOCK FOR FAST DELIVERY! To Order(Specify Model Number) e Description Rating AC A AC5 ac 5 A AC5 Control Signal 5 A AC75 (8 line) 75 A AC9 9 A DC A DC5 dc 5 A DC5 Control Signal 5 A DC75 (8 line) 75 A DC9 9 A AC5 ac 5 A AC75 Control Signal 75 A AC9 ( line) 9 A DC5 dc 5 A DC75 Control Signal 75 A DC9 ( line) 9 A Finned C/W Heat Sink. C/W.7 C/W Shunt Resistors To Order (Specify ) R- R-5 R5- R5-5 Value ohms, watts ohms, 5 watts 5 ohms, watts 5 ohms, 5 watts P-6 s /.67 /.67 /.67 To Order(Specify ) KAX- KAX-5 KAX- KAX-5 KAX-7 KAX-9 KBH-5 KBH-7 KBH-9B Shunt Resistor Guide for Controllers with Triac or Outputs /6.7 Thermally Conductive Compound for Use Between Heat Sink and e Description OT--/ g ( oz) size OT-- 57 g ( oz) size OT--6 5 g ( lb) size Capacity A 5 A A 5 A 7 A 9 A 5 A 7 A 9 A Blocks To Order(Specify ) Compatible s FB- KAX-, KAX-5, KAX- FB- KAX-, KAX-5, KAX- FB- KAX-, KAX-5, KAX- BS- KAX-5, KAX-75, KAX-9, KBH (all models) Controller Resistor Resistor CN, CN, R- 5 R- CN CN9A, CN9, R- R5-5 or CN9A For Additional Controllers and Indicators, See Section M P
5
48 Series - Contactor Relay 4PST - N.O. - Double Make, 15 Amp
48 Series - Contactor Relay 4PST - N.O. - Double Make, 15 Amp E13224 The 48 series is a contactor with a 4 normally open, double make contacts rated up to 3HP. It uses a solenoid type moving core design
More informationRelays. Industrial Automation Catalog Section - U906. Selection Guides. Solid State Relays RSS Series
Industrial Automation Catalog Section - U906 Relays Selection Guides Solid State Relays For up-to-date information, or to request a full copy of this catalog, contact us at www.idec.com or 800-262-IDC..
More informationThe Z Series. SCR Power controllers for resistance heating applications. Zero-Fired SCR Power Controllers AMPS VAC
The Z Series Zero-Fired SCR Power Controllers 60-1200 AMPS 120-600 VAC SCR Power controllers for resistance heating applications. ROBICON 1996 Rev. 7/96 Applications Robicon s Z series power controls are
More informationRSS Series Panel Mount Solid State Relays. 4,000 RMS (minute)
RSS Series Panel Mount Solid State Relays Key features of the RSS series include: Photo isolation 1,200 volt blocking voltage 4,000 volt optical isolation Zero voltage turn-on 100% tested at rated current
More informationOutput Current Input Current Over Load VDC VDC ma ma(typ.) ma(typ.) VDC μf %
Doc. EC-0093 FEATURES Industrial Standard 2"x1" Package Ultra-wide Input Range 9-36VDC, 18-75VDC, 40-160VDC I/O Isolation 3000VAC with Reinforced Insulation Operating Ambient Temp. Range -40 C to +88 C
More information(typ.) (Range) ±18 330# 89 MPW MPW
DC/DC 30W, Single & Dual Output FEATURES 2 x 1.6 x 0.4 Metal Package Ultra-wide 4:1 Input Range Operating Temp. Range 40 C to 80 C Short Circuit Protection I/O-isolation 1500 VDC Input Filter meets EN
More informationThyristor Power Controllers for Resistive and Inductive loads (Product Code 21.3)
Thyristor Power Controllers for Resistive and Inductive loads (Product Code 21.3) 1 Model Wise Descriptions: Sr. No Model Product Description 21.3.1 POW-1 Single Phase SCR Power Controller for single phase
More informationFAMILY. 1-Phase 1 Up to 25A Up to 40A Up to 80A Up to 600VAC 3-Phase, 2 leg 1 No Up to 33A Up to 80A Gang 2 units
THE DIN-A-MITE FAMILY 1 Refer to curves on reverse side for specific ratings. ➁ angle fire is not CE approved for conducted or radiated emissions. ➂ Will fit within the width dimension of most comparable
More informationOutput Current Input Current Reflected Ripple. Efficiency (typ.) (Range) VDC VDC ma ma(typ.) ma(typ.) ma(typ.) VDC μf % MTQZ50-72S05
Doc. EC-0094 FEATURES Industrial Standard Quarter Brick Package Wide Input Range 43-101VDC & 66-1VDC Excellent Efficiency up to 92% I/O Isolation 3000VAC with Reinforced Insulation Operating Ambient Temp.
More informationOutput Current Input Current Reflected Ripple. Efficiency (typ.) Load VDC VDC ma ma ma(typ.) ma(typ.) ma (typ.) VDC μf % MKW40-12S033
DC/DC High Efficiency Regulated Output W Minmax MKW Series FEATURES Smallest Encapsulated W Ultra-compact 2" X 1" Package Wide 2:1 Input Voltage Range Fully Regulated Output Voltage Excellent Efficiency
More informationSolid-State Relays. Solid-State Relays. Features. Description. Overview
Features Rugged, epoxy encapsulation construction 4,000 volts of optical isolation Subjected to full load test and six times the rated current surge before and after encapsulation Unique heat-spreader
More informationOutput Current Input Current Reflected Ripple. Efficiency (typ.) Load VDC VDC ma ma ma(typ.) ma(typ.) ma (typ.) VDC μf % MKW40-12S033
MKW SERIES DC/DC CONVERTER W, Highest Power Density FEATURES Smallest Encapsulated W Ultra-compact 2" X 1" Package Wide 2:1 Input Voltage Range Fully Regulated Output Voltage Excellent Efficiency up to
More informationMotor Controllers Soft Starting/Soft Stopping Types RSC 4.../RSO 12.., RSC 60.../RSO 16..
otor Controllers Soft Starting/Soft Stopping Types RSC 4..../RSO 12.., RSC 60.../RSO 16.. Control and output modules for soft starting/stopping of 3-phase induction motors Rated operational current: 3
More informationSolid-State Relays. Solid-State Relays. Features. Description. Overview
Features Rugged, epoxy encapsulation construction 4,000 volts of optical isolation Subjected to full load test and six times the rated current surge before and after encapsulation Unique heat-spreader
More informationDH50 SERIES. DATASHEET Rev. A
DATASHEET DH50 SERIES 2:1 Wide Input Voltage Ranges Single Outputs, Efficiency up to 92% 2.0 x 1.0 x 0.4 Encapsulated Shielded Metal Package FEATURES RoHS & UL 94V-0 Compliant 50 Watts Output Power 2:1
More informationDC-DC CONVERTERS 4:1 WIDE INPUT RANGE UP TO 9 WATTS SINGLE AND DUAL OUTPUT, SIP PACKAGE SWB9 SERIES
DC-DC CONVERTERS 4:1 WIDE INPUT RANGE UP TO 9 WATTS SINGLE AND DUAL OUTPUT, SIP PACKAGE FEATURES 4:1 Ultra Wide Input Range Output Current up to 2000 ma Miniature SIP (Single-In-Line) Package, 0.86 0.36
More informationOutput Current Input Current Reflected Ripple. VDC VDC ma ma(typ.) ma(typ.) ma(typ.) VDC μf %
FEATURES Industrial Standard Quarter Brick Package Wide Input Range 43-101VDC & 66-1VDC Excellent Efficiency up to 92% I/O Isolation 3000VAC with Reinforced Insulation Operating Ambient Temp. Range - C
More informationVDC VDC ma ma ma(typ.) ma(typ.) ma (typ.) VDC μf % MKW40-12S
MKW SERIES DC/DC CONVERTER W, Highest Power Density FEATURES Smallest Encapsulated W Ultra-compact 2" X 1" Package Wide 2:1 Input Voltage Range Fully Regulated Output Voltage Excellent Efficiency up to
More informationApplication example of a motor controlled by MCD100 and protected by a circuit breaker
VLT T Soft Start Controller MCD 100 MCD 100 is a cost effective and extremely compact soft starter for AC motors up to 11 kw. Due to a unique semiconductor design MCD 100 is a true fit and forget product.
More informationOutput Voltage Current. Input Current Ripple. Efficiency (typ.) Load VDC VDC ma ma ma(typ.) ma(typ.) ma(typ.) μf % 2.
FEATURES Industrial Standard 2" X 1" Package Wide 2:1 Input Voltage Range Fully Regulated Output Voltage High Efficiency up to 88% I/O Isolation 1500 VDC Operating Ambient Temp. Range -40 to 85 Overload
More informationCI-tronic Soft Start Motor Controller Type MCI 25B with Brake
Data sheet CI-tronic Soft Start Motor Controller Type MCI 25B with Brake MCI 25B motor controller with brake is designed for soft starting and braking of 3 phase AC motors. The digital controlled soft
More information(typ.) (Range) Input Specifications Parameter Model Min. Typ. Max. Unit 12V Input Models Input Surge Voltage (100ms.
FEATURES Smallest Encapsulated 50W! Package Size 2.0 x 1.0 x 0.4 Wide 2:1 lnput Range Excellent Efficiency up to 92% Over-Temperature Protection I/O-isolation Voltage 1500VDC Remote On/Off Control Shielded
More informationMJWI20 SERIES FEATURES PRODUCT OVERVIEW. DC/DC Converter 20W, Highest Power Density MINMAX MJWI20 Series
DC/DC 2W, Highest Power Density MINMAX MJWI2 Series MJWI2 SERIES DC/DC CONVERTER 2W, Highest Power Density FEATURES Smallest Encapsulated 2W! Package Size 1. x1. x.4 Ultra-wide 4:1 Input Range Very high
More informationTRC ELECTRONICS, INC DC/DC Converter SIP Package 6W MEAN WELL SPBW06 & DPBW06 Series
/,, MODEL SELECTION TABLE INPUT ORDER NO. INPUT VOLTAGE (RANGE) NO LOAD INPUT CURRENT FULL LOAD VOLTAGE CURRENT EFFICIENCY (TYP.) CAPACITOR LOAD (MAX.) SPBW06F-03 310mA 3.3V 0 ~ 1500mA 81% 4700μF SPBW06F-05
More information2-1. Terms and Characteristics. Description of Terms Cooling Performance of the Automotive IGBT Module
Chapter 2 Terms and Characteristics 1. 2. Description of Terms Cooling Performance of the Automotive IGBT Module 2-5 2-2 2-1 This chapter describes the terms related to the automotive IGBT module and its
More informationEfficiency (typ.) (Range) Output Voltage Current. Input Current Load VDC VDC ma ma ma(typ.) ma(typ.) ma(typ.
FEATURES 2"x 1"x 0.4" Metal Package Wide 2:1 Input Range High Efficiency up to % Operating Ambient Temp. Range 40 C to 80 C Short Circuit Protection I/O-isolation 1500 VDC Input Filter meets EN 55022,class
More informationNote1: Typical values at nominal input voltage and full load. 39VDC. Efficiency vs. Input Voltage. Efficiency [%]
Features ICE Technology* Description +115 C Maximum Case Temperature -45 C Minimum Case Temperature Baseplate Case Style 2250VDC Isolation Wide 4:1 Input Voltage Range EN-50155 and EN-50121-3-2 Certified
More informationNote1: Typical values at nominal input voltage and full load. 39VDC. Efficiency vs. Input Voltage. Efficiency [%]
Features ICE Technology* Description +115 C Maximum Case Temperature -45 C Minimum Case Temperature Built-in EMC Filter Baseplate Case Style 2250VDC Isolation Wide 4:1 Input Voltage Range EN-50155 and
More informationSWITCH-MODE CERAMIC CAPACITORS
Switch-Mode ceramic capacitors feature large capacitance values and exhibit low ESR (equivalent series resistance) and low ESL (equivalent series inductance) making them well suited for high power and
More informationLedex Rotary Solenoids Modifications and Custom Capabilities
Ledex Rotary Solenoids Modifications and Custom Capabilities Modifications and Customized Units For modifications including heavy duty return springs, drive pins, etc. please contact our application engineers
More informationCHASSIS MOUNT DC-DC CONVERTERS 4:1 WIDE INPUT RANGE, 150 WATTS RAILWAY APPLICATIONS FWB(D)150 SERIES*
CHASSIS MOUNT DC-DC CONVERTERS 4:1 WIDE INPUT RANGE, 150 WATTS RAILWAY APPLICATIONS * FEATURES 4:1 Wide Input Range (9-36, 43-160Vdc) No Minimum Load Required High Efficiency: Up to 89% Built In EN55011
More informationNotes: Note1: values at nominal input voltage and full load. 8.5VDC 5V 8V. Open, Efficiency vs. Input Voltage. Efficiency [%]
Features ICE Technology* Description +115 C Maximum Case Temperature -45 C Minimum Case Temperature Built-in EMC Filter Ribbed Case Style 22VDC Isolation Wide 4:1 Input Voltage Range EN-522 Class B The
More informationSolid State Relays Datasheet WG 480 D...Z
Datasheet WG 4 D...Z Features Switching Zero cross Output Input Back to back SCR with internal snubber DC with constant current control Applications Resistive and inductive loads with cos > 0.85 Technical
More informationPART NUMBER STRUCTURE. P-DUKE Technology Co., Ltd Page 1
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE FED60-48 S 05 W - M3 N HC Series Name Input Output Output Input Operating Temp. Remote
More informationSolid State Relays Datasheet WG 480 D...Z
Datasheet WG 4 D...Z Features Switching Zero cross Output Input Back to back SCR with internal snubber DC with constant current control Applications Resistive and inductive loads with cos > 0.85 Technical
More information(with Class-1 AC resistive load) 3. G3PB-215B-2N-VD kW max. (25 A) G3PB-225B-3N-VD 2. G3PB-225B-2N-VD kw max. (35 A) G3PB-235B-3N-VD 2
Solid-state Contactor (New Heat Sink Construction) G3PB Space and working time saved with new heat sink construction. Series now includes 480-VAC models to allow use in a greater range of applications.
More informationRCD15W Series PART NUMBER STRUCTURE
DC/DC Railway Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV PART NUMBER STRUCTURE RCD15-48 S 05 W - M3 A HC Series Name Input Output Output Input Operating Temp.
More informationC B. Operating up to 5000m altitude 5 year product warranty Models
DC/DC Converter Wide 2:1 input voltage 6 W DC/DC converter in a compact DIP-24 plastic case I/O isolation 5000 VACrms rated for 250 VACrms working voltage Certification according to IEC/EN/ES 60601-1 3rd
More information(typ.) (Range) Load
FEATURES Highest Power Density 1" x 1" x 0.4" Shielded Metal Package Wide 2:1 Input Range Excellent Efficiency up to % Operating Temp. Range - C to + C Optional Heatsink I/O-isolation Voltage 10VDC Remote
More information1SVC F SVC F 0607 R100.20/30 R100.45
SIGMASWITCH Content Solid state relays Description, certificates, approvals... 163 Ordering details... 164 Technical data R111, R12x... 167 Technical data R100... 168 Technical data HDS R2... 169 Selection
More informationPG02S Series 2W DC/DC CONVERTER, SIP-Package
PG02S Series 2W DC/DC CONVERTER, SIP-Package FEATURES Efficiency up to 81% SIP Package with Industry Pinout Small Footprint: 21.8 x 9.3 mm (0.86 x 0.37 inch) Wide 2:1 Input Range Operating Temperature
More informationS24SP series 40W Single Output DC/DC Converter
4W Single Output DC/DC Converter FEATURES Efficiency up to 92.8% Wide input range, 9V-36V Package with Industry Standard Pinout Package Dimension: Without heat sink 5.8 x25.4 x1.2mm (2. x1. x.4 ) With
More informationMAKING MODERN LIVING POSSIBLE. Design Guide VLT MCD 100 Soft Starter the single speed drive
MAKING MODERN LIVING POSSIBLE Design Guide VLT MCD 100 Soft Starter the single speed drive Contents Contents 1.1.1 Introduction 2 1.2 Technical Data 3 1.3.1 Functional Diagram 4 1.3.4 Wiring 5 1.3.5 Adjustments
More informationSolid-State Relays. Solid-State Relays. Features. Description. Overview
Features Rugged, epoxy encapsulation construction 4,000 volts of optical isolation Subjected to full load test and six times the rated current surge before and after encapsulation Unique heat-spreader
More informationPDL09-48 S 05 M Series Name Input Output Output Case Voltage Quantity Voltage Option PART NUMBER STRUCTURE
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE PDL09-48 S 05 M Series Name Input Output Output Case Voltage Quantity Voltage Option
More informationMatrix APAX. 380V-415V 50Hz TECHNICAL REFERENCE MANUAL
Matrix APAX 380V-415V 50Hz TECHNICAL REFERENCE MANUAL WARNING High Voltage! Only a qualified electrician can carry out the electrical installation of this filter. Quick Reference ❶ Performance Data Pages
More informationCI-Tronic Soft start motor controller MCI 3, MCI 15, MCI 25, MCI 30 I-O, MCI 40-3D and MCI 50-3 I-O
Data sheet CI-Tronic Soft start motor controller MCI 3, MCI 15, MCI 25, MCI 30 I-O, MCI 40-3D and MCI 50-3 I-O The MCI soft starters are designed for soft starting and stopping of 3 phase AC motors, thus
More informationSH01S/D Series 1W DC/DC CONVERTER, SMD-Package
SH01S/D Series 1W DC/DC CONVERTER, SMD-Package FEATURES Efficiecny up to 80% SMD Package with Industry Standard Pinout Operating Temperature Range 40 C to +8 C Moisture sensitivity level (MSL) 2 Isolation
More informationHAE S 05 - P TH HS PART NUMBER STRUCTURE Page 1. P-DUKE Technology Co., Ltd.
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE HAE100-48 S 05 - P TH HS Series Name Input Output Output Ctrl and Through hole Assembly
More informationDesign Guide. VLT Soft Start Controller MCD 100
Design Guide VLT Soft Start Controller MCD 100 Introduction The MCD 100 soft starters are designed for soft starting and stopping of 3 phase a.c. motors, thus reducing the inrush current and eliminating
More informationDPX30-xxSxx DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; 3.3 to 28 VDC Single Output; 30 Watts Output Power
DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; 3.3 to 28 VDC Single Output; 30 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW TERMINALS
More informationOutput Current Input Current Over Voltage. VDC VDC ma ma(typ.) ma(typ.) VDC μf % MKZI10-24S
Doc. E-92 MKZI1 SERIES D/D ONVERTER 1W, Reinforced Insulation, Railway ertified FEATURES Industrial Standard 2" 1" Package Ultra-wide Input Range 9-36VD, 18-75VD, -1VD I/O Isolation 3VA with Reinforced
More informationEPIC Hermetic Sealed DC and AC Contactor Amp Power Switching RoHS Compliant, all date codes
EPIC Hermetic Sealed DC and AC Contactor - 150+ Power Switching RoHS Compliant, all date codes File E320908 All contact ratings and coil versions may not be UL recognized. Contact GIGAVAC for a copy of
More informationRE-PR3-E-86&105 3-Phase Panel Mount 86 and 105kW
Page 1 of 6 3-Phase Panel Mount 86 and 105kW Features: Benefits: 0-10Vdc, 0-5Vdc, 4-20mA or manual via potentiometer control input Over temperature protection with auto reset Enclosed panel mounting Efficient
More information25 to 30 Watt XW Single Series DC/DC Converters
Features 4: Input Voltage Range Low Noise, Highly Regulated Efficiencies to 4 at Full Load No Derating to C Case Temperature Six-Sided Continuous Shielded, Low Thermal Gradient Copper Case Minimum Input
More informationDPX30-xxDxx DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power
DC-DC Converter Module 9.5 ~ 18 VDC and 18 ~ 36 VDC and 36~ 75 VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW TERMINALS
More informationDC-DC CONVERTERS 2:1 INPUT RANGE, UP TO 2 WATTS MEDICAL APPLICATIONS MTWA2 SERIES
DC-DC CONVERTERS 2:1 INPUT RANGE, UP TO 2 WATTS MEDICAL APPLICATIONS FEATURES 2:1 Wide Input Voltage Range: 4.5-12 Input, 9-18 and 18-36 and 36-75 5000Vac Input to Output 2MOPP Isolation Remote On/Off
More informationDPX30-xxWSxx DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; 3.3 to 28VDC Single Output 30 Watts Output Power
DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; 3.3 to 28VDC Single Output 30 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW TERMINALS FOR INPUT AND OUTPUT
More informationDPX30-xxWDxx DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power
DC-DC Converter Module 10 ~ 40VDC, 18 ~ 75VDC input; ±12 to ±15 VDC Dual Output; 30 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW TERMINALS FOR INPUT AND
More informationDIN-A-MITE C. SCR Power Controller Delivers Up To 80 Amperes in a Compact Package. TOTAL CUSTOMER SATISFACTION 3 Year Warranty. Features and Benefits
DIN-A-MITE C TOTAL CUSTOMER SATISFACTION 3 Year Warranty SCR Power Controller Delivers Up To 80 Amperes in a Compact Package The DIN-A-MITE C silicon controlled rectifier (SCR) power controller provides
More informationLED Driver Linear / area fixed output industry. Driver LCI 100W 350mA 900mA TOP INDUSTRY sl TOP series
Driver LCI 100W 350mA 900mA TOP INDUSTRY sl TOP series Product description Fixed output constant current built-in LED Driver, particularly suitable for industrial applications in tough enviromments such
More informationSCR POWER REGULATORS & HEATING CONTROL PANELS. 1/2/3-Phase 15 ~ 750+ Amps 220 ~ 480 V AC.
SCR POWER REGLATORS & 1/2/3-Phase 15 ~ 750+ Amps 220 ~ 480 V AC SCR POWER REGLATORS & Radix SCR Power Regulators Radix offers a full range of SCR Power Regulators as well as SCR Heating Control Panels.
More informationDrop-in Alternative to Tyco/Kilovac* 500+ Amp EV200, plus a lot more (Compare Products) RoHS Compliant, all date codes
Drop-in Alternative to Tyco/Kilovac* 500+ Amp EV200, plus a lot more (Compare Products) RoHS Compliant, all date codes Patent Pending File E320908 All contact ratings and coil versions may not be UL recognized.
More informationDCMCW60 SERIES FEATURES
DATASHEET DCMCW SERIES 4:1 Ultra Wide Input Voltage Ranges - C to +95 C Operating Temperature Single Outputs, Standard APPLICATIONS Distributed Power Systems Measurement Equipment Telecom Wireless Networks
More informationSCR Power Controllers
SCR Power Controllers Instruction Manual SCR POWER CONTROLLERS TABLE OF CONTENTS General Description and Specifications...1 Firing Modes....2 Installation and Wiring...4 Operation...9 Troubleshooting...15
More informationXLR Energy Storage Module
Technical Note 19 XLR Energy Storage Module XLR Energy Storage Module Safety The XLR 48 V module contains stored energy of 54 watt-hours and can discharge up to 97 amps if short circuited. Only personnel
More informationModel Number Output Voltage Output Amps Input Range Max. Iin FL Efficiency Max Output Power
Small 2.32 x 0.9 x 0.37 Size Constant Frequency High Typical Efficiency of 90% (12Vout) Low Output Noise 18 to 60VDC Input Voltage Range Output Over Voltage Protection Current Limit/Short Circuit Protection
More informationHAE S 05 - P HS Series Name Input Output Output Ctrl and Assembly Option Voltage Quantity Voltage Pin Options
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE DIP Type: HAE100-48 S 05 - P HS Series Name Input Output Output Ctrl and Assembly Option
More informationDPX15-xxWDxx Dual Output: DC-DC Converter Module 9.5 ~ 36VDC, 18 ~ 75VDC input; ±5 to ±15 VDC Dual Output; 15 Watts Output Power
DPX15-xxWDxx Dual Output: DC-DC Converter Module 9.5 ~ 36VDC, 18 ~ 75VDC input; ±5 to ±15 VDC Dual Output; 15 Watts Output Power FEATURES NO MINIMUM LOAD REQUIRED 1600VDC INPUT TO OUTPUT ISOLATION SCREW
More informationTemperature Controllers
Controllers SCR Power Controllers Introduction to Silicon Controlled Rectifier (SCR) Power Controllers Features and Benefits of SCRs High reliability Because the SCR power controller is a solid-state device,
More informationAMS Amp LOW DROPOUT VOLTAGE REGULATOR. General Description. Applications. Typical Application V CONTROL V OUT V POWER +
5 Amp LOW DROPOUT OLTAGE REGULATOR General Description The AMS1505 series of adjustable and fixed low dropout voltage regulators are designed to provide 5A output current to power the new generation of
More informationHAE S 05 W - P TH HS PART NUMBER STRUCTURE Page 1. P-DUKE Technology Co., Ltd.
Railway Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV PART NUMBER STRUCTURE HAE100-48 S 05 W - P TH HS Series Name Input Output Output Input Ctrl and Through hole
More informationEfficiency Model dependant 86 ~ 88% Isolation. Isolation Cap. Switching Freq. Safety. Case Material Base Material Potting.
DC/DC Converter Si ngle Output: 150 Watts DIN Rail -Option STD-Panel Mount / HC Features 4:1 wide Input range: 9~36V,18~75V & 43~160VDC Single output, up to 12.5A / 150 watts Rail EN50155 compliance High
More informationHALF-BRICK DC-DC CONVERTERS 4:1 ULTRA WIDE INPUT RANGE 100 WATT RAILWAY APPLICATIONS HWB100 SERIES
HALF-BRICK DC-DC CONVERTERS 4:1 ULTRA WIDE INPUT RANGE WATT RAILWAY APPLICATIONS FEATURES No Minimum Load Required 225 Input to Output Basic Insulation Railway Applications 4:1 Wide Input Voltage Range
More informationABB Softstarter Benefits Charnchanok Thongprad
ABB Softstarter Benefits Charnchanok Thongprad tomation Technology Products AB Control - 1 - - Why Softstarters? Benefits for the Electrical network Reduces voltage drops on networks Minimizes starting
More informationTemperature Controllers
SCR Power Controllers Introduction to Silicon Controlled Rectifier (SCR) Power Controllers Features and Benefits of SCRs High reliability Because the SCR power controller is a solid-state device, it provides
More information1SMA10CAT3G Series, SZ1SMA10CAT3G Series. 400 Watt Peak Power Zener Transient Voltage Suppressors. Bidirectional
110CAT3G Series, SZ110CAT3G Series 400 Watt Peak Power Zener Transient Voltage Suppressors Bidirectional The series is designed to protect voltage sensitive components from high voltage, high energy transients.
More informationS24SP15004 series 60W Single Output DC/DC Converter
6W Single DC/DC Converter FEATURES Efficiency up to 93.3% Wide input range, 9V-36V Package with Industry Standard Pinout Package Dimension: Without heat sink 5.8 x25.4 x1.5mm (2. x1. x.41 ) With heat sink
More informationSST-ST75F-ESS The essential silver standard
STRIDER ESSENTIAL SERIES SST-ST75F-ESS The essential silver standard High efficiency with 80 PLUS Silver certification 24/7 continuous power output with 40 operating temperature Class-leading single +12V
More informationTC-500PD8. Switching Power Supply ( PS2 A T X 500W 8 0+ ) SPECIFICATION. Revision: 2.0
TC-500PD8 TC-500PD8 Switching Power Supply ( PS2 A T X 500W 8 0+ ) SPECIFICATION Revision: 2.0 727,. Phillips Drive City of Industry. CA 91748. USA http:// www.xeal.com.tw TEL: 626-303-8885 FAX: 626-301-0588
More informationPOWERBOX Industrial Line PMF20W Series 20W 4:1 Single Output DC/DC Converter Manual. DC/DC Converter Features. Introduction
Table of Contents Output specification Input specification General specification Environmental specifications EMC characteristic curves Output voltage adjustment Input source impedance Output over current
More informationDriver LC 17W mA flexc C EXC EXCITE series
LC 17 W 250 700 flexc C EXC - Tridonic Seite 1 von 5 Home Products LED Drivers Compact fixed output EXCITE series LC 17 W 250 700 flexc C EXC Driver LC 17W 250 700 flexc C EXC EXCITE series Product description
More informationQS20.241, QS C1
QS2.21, QS2.21C1 QSeries 27. APPLICATION NOTES 27.1. REPETITIVE PULSE LOADING Typically, a load current is not constant. It varies over time. For pulse load compatibility, following rules must be met:
More information2W, Low Cost DIP, Dual Output DC/DC Converters
2W, Low Cost DIP, Dual Output DC/DC s Key Features Low Cost 500 Isolation MTBF > 0,000 Hours mv P-P Ripple and Noise Input 12 Output {15 Temperature Performance -25] to +71] Short Circuit Protection UL
More informationStarting Torque Limiter Type TCI (Soft Start)
Data sheet Starting Torque Limiter Type TCI (Soft Start) Starting Torque Limiters are designed for the soft starting of single and tree phase AC motors. The controller allows smooth starting of all AC
More informationRDL06-48 S 05 W - M3 Series Name Input Output Output Input Operating ambient Voltage Quantity Voltage Range temperature PART NUMBER STRUCTURE
Railway Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV PART NUMBER STRUCTURE RDL06-48 S 05 W - M3 Series Name Input Output Output Input Operating ambient Voltage
More information55 Watt K Triple Series DC/DC Converters
Features Very Low Noise, < mv P-P Maximum PCB Mounting with Optional Heat Sink or Chassis Mount Versions Efficiencies to 87 Common and Differential Mode Input Filtering Remote Sense On + Volt Output Single
More informationLED Driver Linear / area fixed output industry. Driver LCI 65W 150mA 400mA TOP INDUSTRY sl TOP series
Driver LCI 65W 150mA 400mA TOP INDUSTRY sl TOP series Product description Fixed output constant current built-in LED Driver, particularly suitable for industrial applications in tough enviromments such
More informationThe High Power Stack Horizon
Voltage Supply 480-600-690V Current Rating from 150 to 2100A Designed to drive 1-2-3 Phase Loads Internal Fuse with Micro for Fuse Failure Stall Fan Protection for 1100 to 2100A Control Board with Plug
More informationRP40- _FR/ Package (4) CTRL Logic (3)
Features Regulated Converters Description Wide 4:1 Input Voltage Range 1.6kVDC Isolation for 24Vin and 48Vin, 3kVDC Isolation for 1Vin Efficiency up to 92% Six-Sided Continuous Shield UL695-1 AM2 Certified,
More information150 WATT HEW SINGLE SERIES DC/DC CONVERTERS
Features Description The 4:1 Input Voltage 150 W single HEW Series of DC/DC converters provide precisely regulated dc outputs. The output voltage is fully isolated from the input, allowing the output to
More information3A L.D.O. VOLTAGE REGULATOR (Adjustable & Fixed)
FEATURES Output Current of 3A Fast Transient Response 0.04% Line Regulation 0.2% Load Regulation Internal Thermal and Current Limiting Adjustable or Fixed Output oltage(1.5, 1.8, 2.5, 3.3, 5.0) Surface
More informationData sheet. CI-tronic Soft start motor controller Type MCI 3, MCI 15, MCI 25, MCI 30 I-O, MCI 50 I-O 520B1443
CI-tronic Soft start motor controller Type MCI 3, MCI 15, MCI 25, MCI 30 I-O, MCI 50 I-O December 2002 DKACT.PD.C50.G2.02 520B1443 2 DKACT.PD.C50.G2.02 Danfoss A/S 12-2002 Introduction The MCI soft starters
More informationSwitching Power Supplies
Features Boxed Power Supplies with Screw Terminal Block Single- and Triple Output Models EMI Compliance with EN 55022 and FCC Part 15, Level B Short Cirquit Protection Overvoltage Protection High Efficiency
More informationLoad (2) Single or Dual
Features Regulated Converter Reinforced insulation for 25VAC working voltage Clearance and creepage distance >8.mm 5kVAC I/P to O/P 2MOPP isolation 2µA patient leakage current Industry standard pinout
More informationFeatures. Regulated Converters. RP20-F 20 Watt 2 x 1 Single & Dual Output. RP20- _F/ Package 4) Control Logic (3) DC/DC Converter
Features Regulated Converters Description 2:1 Wide Input Voltage Range 1.6kV Isolation UL Certified Efficiency up to 89% Six-Sided Continuous Shield No Minimum Load The series / converters are certified
More informationTeSys contactors. Use in category DC-1 (resistive loads; time constant L/R y 1 ms) Rated operational current Ie. to be wired in series
Selection 3-pole shockproof contactors FG d.c. supply Selection guide for utilisation categories DC-1 to DC-5 Use in category DC-1 (resistive loads; time constant L/R y 1 ms) Rated operational current
More informationXLM 62V Energy Storage Module
Technical Note 10406 XLM Energy Storage Module XLM 62V Energy Storage Module Introduction The XLM energy storage modules are self-contained energy storage devices comprised of twenty-three individual supercapacitor
More informationLED Driver Linear / area fixed output
Driver LC 65W 4-7mA flexc lp ANCED series Product description Built-in constant current LED Driver Adjustable output current between 4 and 7 ma Max. output power 65 W Up to 94 % efficiency Nominal life-time
More informationFeatures. LED Driver. RACT09 9 Watt. TRIAC Dimmable. Single Output RACT09- AC/DC Converter
Features TRIAC Dimmable LED Driver Triac dimmable with leading or trailing edge dimmers Class II with SELV output (no earth required) Extra-large screw terminals and integrated cable clamps for easy installation
More information