SERIES. Dirty Environment Oil Coolers ACD

Transcription

1 ACD Dirty Environment Oil Coolers SERIES Low Fouling Series with Non-Louvered Fin Design Standard s with Higher Speed Fans for Compact, Most Economical Selection Low Noise s with Slower Fan Speeds for Reduced Noise Levels and Lower Fan HP Requirements Competitive Pricing Deliveries From Stock THERMAL SYSTEMS, INC. BULLETIN ACDB-2

2 AKG ACDB-2 6/24/03 1:01 PM Page 2 Standard s HEAT REJECTION Horsepower F ETD PERFORMANCE DATA STANDARD MODELS ACD SERIES OIL P = 5 PSI = 10 PSI = 25 PSI = PSI SUS OIL ACD 16 ACD 8 ACD 40 ACD 30 ACD 1 ACD 130 ACD 100 ACD 70 ACD 2 NOISE LEVELS db A SCALE AT 1 METER db(a) ACD 8 80 ACD ACD ACD ACD ACD ACD ACD 1 98 Size ACD 8 ACD 16 ACD 30 ACD 40 ACD 70 ACD 100 ACD 130 ACD 1 ACD 2 HP RPM 1/3 32 1/2 32 1/ Motor Frame IEC 63 IEC 71 56C 56C 56C 184TC 213TC 213TC 215TC OIL FLOW - GPM 115/230 ELECTRIC MOTOR DATA SINGLE PHASE Amps 230 V / / / Consult Factory THREE PHASE ACD / / / /440 /220 /440 /220 / /480 Amps 230V

3 Low Noise s HEAT REJECTION Horsepower F ETD300 PERFORMANCE DATA STANDARD MODELS ACDL SERIES OIL P = 5 PSI = 10 PSI = 25 PSI = PSI SUS OIL ACDL 16 ACDL 8 ACDL 40 ACL 30 ACDL 2 ACDL 130 ACDL 100 ACDL 70 ACDL 1 NOISE LEVELS db A SCALE AT 1 METER ACDL 8 ACDL 16 ACDL 30 ACDL 40 db(a) ACDL ACDL ACDL ACDL 1 88 Size HP RPM Motor Frame OIL FLOW - GPM ELECTRIC MOTOR DATA SINGLE PHASE Amps 230 V. THREE PHASE ACDL 2 90 Amps 230V ACDL 8 1/ IEC 63 Consult 230/ / ACDL 16 1/3 IEC Factory 230/ / ACDL 30 1/ / /220 / ACDL 40 1/ / /220 / ACDL /480 3/4 115/208/ ACDL ACDL TC Consult Factory 7.6 ACDL / TC 16.0 ACDL / TC 23.0

4 Selection Procedures The performance curves above are based on the following: SUS Oil. F Entering Temperature Difference (ETD) If your application conditions are different, use the following selection procedure: STEP 1. Determine the Heat Load In most cases you can use 1/3 of the input horsepower. Example: 30 HP Power Unit = 10 HP Heat Load STEP 2. Determine the Actual ETD Desired Entering OIL Temperature Entering AIR Temperature = ETD The entering oil temperature is the highest desired oil temperature. The entering air temperature is the highest anticipated ambient air temperature, plus any pre-heating of the air prior to its entering the cooler. STEP 3. Calculate the Adjusted BTU/hr for Selection Horsepower Horsepower For x = Heat Load Desired ETD Use With Selection Chart CORRECT ON FACTOR OIL PRESSURE DROP CORRECTION OIL VISCOSITY SUS STEP 4. Select The From The Curves Read up from the GPM to the required heat rejection. Select any model on, or above this point. STEP 5. Calculate Oil Pressure Drop Find the oil pressure drop correction factor and multiply it by the oil pressure drop found on the performance curve. Specifications RATINGS: Maximum Working Pressure...2 PSI Maximum Working Temperature...2 F MATERIALS: Cooler...Alumium Shroud...Powder Painted Steel Fan Guard...Zinc Plated Steel Fan Blade...Polypropylene Blades Aluminum Hub Mounting Brackets...Powder Painted Steel

5 AKG ACDB-2 6/24/03 1:01 PM Page 1 Dimensions G SAE Fitting Typ. 2 B C (Approx.) D A E F H K L J M MODEL A B C D E F G H J K L M (Approx.) ACD #16 SAE ACD UN-2B M8x10 Bolt (4 PL) Approx. Weights Net Shipping ACD #20 SAE ACD UN-2B M10x20 Bolt (8 PL) ACD ACD SAE 4-Bolt M12x20 3 FLANGE Bolt ACD (8 PL) ACD SAE Bolt ACD FLANGE x1 1 2 Bolt (8 PL) Dimensions are in inches. We reserve the right to make reasonable design changes without notice. Weights are in pounds. Electric motors are totally enclosed, and are not thermally protected. Actual ratings vay with motor brand. Check motor nameplate for actual ratings. Motor RPM is reduced by 1/6 for service. Ordering Information ACD SERIES MODEL SIZE MOTOR DATA CUSTOM FEATURE CODE Standard SELECTED 0=NO MOTOR R=REVERSED AIR FLOW C=CORE ONLY AD=SAE TO NPT ADAPTORS INSTALLED ACDL SERIES 1= SINGLE PHASE H=HERESITE COATING/CORE ASSEMBLY Low Noise 3=THREE PHASE CRN=CANADIAN REGISTRY, 2 PSI 575=575 VOLT CRS=CANADIAN REGISTRY, 1 PSI

6 Worldwide AKG has been manufacturing high quality coolers and cooling systems since We have grown to include 10 facilities with over 1400 employees to serve you. Your Business Partner AKG Worldwide Partnership Customer AKG is a complete single source supply for all of your cooling requirements. Choose from both standard and custom engineered products depending on your specific needs. AKG believes in solid long-term business relationships built on partnerships with its customers. AKG places heavy emphasis on development of leading edge technologies, products and finding creative solutions to our customers individual requirements. AKG Thermal Systems, Inc. Mebane Industrial Park 809 Mattress Factory Road P.O. box 189 Mebane, North Carolina Tel.: (919) Fax: (919) Autokühler GmbH & Co. KG Postfach 1346 D Hofgeismar Tel.: / Fax: / Internet: Info@akg-gruppe.de