Available manual, pneumatic, and hydraulic spool control kits.
|
|
- Dwain Cooper
- 5 years ago
- Views:
Transcription
1 Fitted with a main pressure relief valve and a load check valve on every working section. Available with parallel circuit. Optional carry-over Variety of port valves (auxiliary valves) Available manual, pneumatic, and hydraulic spool control kits.
2 This catalogue shows technical specifications and diagrams measured with mineral oil of 32 mm 2 /s 32 cst at 4 o C 14 o F temperature. Nominal flow rating 16 l/min 42 US gpm Operating pressure (max.) 31 bar 46 psi Back pressure (max.) outlet port T 2 bar 36 psi Internal leakage (max.) A(B) T Fluid Fluid temperature Viscosity Δp = 1 bar (14 psi) fluid and valve at 4 o C (14 o F) 1 cm 3 /min.91 in 3 /min Mineral based oil with NBR from -2 o C to 8 o C from -4 o F to 176 o F with FPM from -2 o C to 1 o C from -4 o F to 212 o F operating range from 1 to 7 mm 2 /s from 1 to 7 cst min. 12 mm 2 /s 12 cst max. 4 mm 2 /s 4 cst Max contamination level -/19/16 - ISO 446 NAS class 1 Ambient temperature for working conditions with mechanical devices from -4 o C to 6 o C from -4 o F to 14 o F with pneumatic and hydraulic devices from -3 o C to 6 o C from -22 o F to 14 o F with electric devices from -2 o C to o C from -4 o F to 122 o F Note for different conditions please contact Sales department Reference standard BSP UN-UNF NPTF ISO 228/1 ISO 263 THREAD ACCORDING TO ANSI B1.2.3 BS 2779 ANSI B1.1 unified ISO CAVITY DIMENSION SAE J J476a ACCORDING TO DIN Ports BSP UN-UNF Order code G34 G1 SAE Inlet P G 3/4 G 1 1 /16-12 (SAE16) Ports A and B G 3/4 1 1/16-12 (SAE12) Outlet T and carry-over C G 1 1 /16-12 (SAE16) Hydraulic pilots G 1/4 9/16-18 (SAE6) Pneumatic pilots NPTF 1/8-27 2
3 General 4 P T pressure drop 2 P A(B) pressure drop 2 P A(B) pressure drop sections 1 1 P A12(B12) P A6(B6) P A1(B1) 1 1 A1(B1) T A6(B6) T A12(B12) T 1 6 sections 1 section Main pressure relief valve 4 Valve setting range for the direct operating relief valve 4 Valve setting range for the pilot operating relief valve standard setting Auxiliary valves 4 3 Valve setting range for YD relief valve (1-2 bar setting) 4 3 Valve setting range for YP relief valve 2 standard setting 2 standard setting 1 1 3
4 Type E F E F Type mm in mm in mm in mm in KS , ,88 7KS , ,22 2KS , ,77 8KS , ,11 3KS , ,66 9KS , 8 2, 4KS , , 1KS , ,89 KS , ,44 11KS , ,78 6KS , ,33 12KS , ,67 4
5 Open center configuration Carry-over configuration Closed center configuration
6 / K S 1 8 / L 1 ( D ) - / P A 1 ( A o B y D - 1 ) K Z 1 / P A 1 H ( A o B o ) / T 1 / G 1 1 L1: Inlet section with side port L2: Inlet section with upper port R1: Right inlet section with side port R2: Right inlet section with side port 2 (svp): Relief valve blanking plug Direct type D: (D-8): Setting range from 63 to 12 bar (9 to 18 psi), standard setting 8 bar (116 psi). (D-12): Setting range from 1 to 2 bar (14 to 29 psi), standard setting 17 bar (2 psi). (D-2): Setting range from 16 to 32 bar (23 to 46 psi), standard setting 2 bar (36 psi). Pilot operated type P: (P-12): Setting range from 6 to 2 bar (87 to 36 psi), standard setting 12 bar (17 psi). 3 -: Blanking plug (omit in description) F: Inlet anticavitational valve L: Hydraulic pilot unloader valve EL: Solenoid operated unloader valve: ELN: Without emergency ELP: Push-button emergency ELV: Screw type emergency ELT: Push and twist type with detent emergency Coils for EL: 12VDC: Coil type KETA, ISO V DC 24VDC: Coil type KETA, ISO V DC 6
7 4 P: Parallel circuit with port valves arrangemen A: Double acting, 3 positions, with A and B closed in Af: Same as A, more sensitive. B: Single acting on A, 3 positions, B plugged. C: Single acting on B, 3 positions, A plugged. D: Double acting, 3 positions, with A and B open to tank in E: Double acting, 3 positions, with B open to tank in F: Double acting, 3 positions, with A open to tank in 6 1: With spring return in 2: With detent in position 1 and spring return in 3: With detent in position 2 and spring return in 4: 2 positions, position 2 and spring return in : 2 positions, position 1 and spring return in 6: 2 positions, position 1 and spring return in position 2. 7: 2 positions, position 2 and spring return in position 1. 8: Detent in position neutral, 1 and 2. 9: 2 positions, detent in positions 1 and neutral. 1: 2 positions, detent in positions 2 and neutral. 11: 2 positions, detent in positions 1 and H: Double side proportional hydraulic control with spring return to neutral 8 о: Valve blanking plug Antishock valve YD-63: Setting range from 63 to 12 bar (9 to 18 psi), standard setting 63 bar (9 psi). YD-1: Setting range from 1 to 2 bar (14 to 36 psi), standard setting 1 bar (14 psi). YD-2: Setting range from 2 to 31 bar (29 to 46 psi), standard setting 2 bar (29 psi). Antishock and anticavitational valve ZD-63: Setting range from 63 to 12 bar (9 to 18 psi), standard setting 63 bar (9 psi). ZD-1: Setting range from 1 to 2 bar (14 to 36 psi), standard setting 1 bar (14 psi). ZD-2: Setting range from 2 to 31 bar (29 to 46 psi), standard setting 2 bar (29 psi). Antishock pilot operated valve YP: Setting range from 63 to 3 bar (9 to 43 psi), standard setting 17 bar (2 psi). 7 Antishock and anticavitational pilot operated valve ZP: Setting range from 63 to 3 bar (9 to 43 psi), standard setting 17 bar (2 psi). 9 - : Without lever box, with dust-proof plate KZ1: Standard lever box V1: CD flexible cable connection 1 T1: With side outlet. T2: With upper outlet. TC1: With closed center. TC2: With upper outlet and side carry over. 11 Specify thread type, please, refer to page 2 to see codes for it.
COMPACT CATALOG MONOBLOCK DIRECTIONAL CONTROL VALVES
COMAC CAALOG MONOBLOCK DIRECIONAL CONROL VALVES SD4 Features Simple, compact designed, this valves is only one section for open center and closed center hydraulic systems. H Fittedwithamainpressurereliefvalve.
More informationSDS400. Sectional directional control valve
SDS4 Sectional directional control valve SDS4 Features Sectional directional control valve for high flow, available for fixed displacements hydraulic pumps. From to work sections Open centre Optional carry-over
More informationMONOBLOCK DIRECTIONAL CONTROL VALVES
MONOBLOCK DIRECTIONAL CONTROL VALVES CONTENTS: RM0...... RM5...... RM40P...... RM80...... RMD90...... MRP70... Page 1/19&/19 /19...5/19 6/19...10/19 11/19...15/19 16/19&17/19 18/19&19/19 MONOBLOCK DIRECTIONAL
More informationORV-M45. Contents. Additional Informations
Contents Working Conditions 3 Dimensional Data 4 Hydraulic Circuit 5 Performance Data And Curve 7 Inlet Relief Options 8 Ordering Codes 9 Spool Options 11 Spool Positioners Side of Return 14 Spool Positioners
More informationUmschaltventile DF20/3. mit Hebel Bestellnr. Typ Code
Umschaltventile DF/3 Bestellnr. Typ Code mit Hebel 4-- DF/3AL 64 4-- DF/3A7L 6744 4-- DF/3A7SLP 64 4-- DF/3AT7SLP 64 4-- DF/3BC7CB 674 4-- DF/3AC7CA-TAP(A) 64 4--3 DF/3B7MEIA-TAP(B) 648 4--4 DF/3AMB 6
More informationPilot Operated Pressure Relief Valve Series R5V (Denison)
Characteristics Pilot operated pressure relief valves series R5V have a similar design to the subplate mounted R4V series. The SAE flanges allow to mount the valves directly on the outlet flanges of pumps
More informationNV452 Monoblock directional control valve
NV452 Monoblock directional control valve Product Features General Specifications Order Coding Open Center Load Sense Performance Data Inlet Options Spool Positioners Spool Options Auxilary Valves Lever
More informationDirectional Control Valve CV550
www.nimco-controls.com Directional Control Valve CV550 Smart Solutions... for the Future Contents Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 16 Page 17 Page 18 Page
More informationCOMPACT CATALOG MONOBLOCK DIRECTIONAL CONTROL VALVES
COMAC CAALOG MONOBLOCK DIRECIONAL CONROL VALVES Features Simple, compact designed, this valve is only one section for open center and closed center hydraulic systems. H Fitted with a main pressure relief
More informationCOMPACT CATALOGUE SECTIONAL DIRECTIONAL CONTROL VALVES
COMAC CAALOGUE SECIONAL DIRECIONAL CONROL VALVES Features Simple, compact and heavy duty designed sectional valve from to sections for open and closed centre hydraulic systems. H Fitted with a main pressure
More informationCOMPACT CATALOGUE SECTIONAL DIRECTIONAL CONTROL VALVES
COMAC CAALOGUE SECIONAL DIRECIONAL CONROL VALVES SDS5 Features Simple, compact and heavy duty designed sectional valve from to sections for open and closed centre hydraulic systems. H Fitted with a main
More information-Technical data... 2/14 -Circuit mode... 2/14 -Dimensions RP /14
Auxiliary valves Document: SCV-1-June 2013 Lever Spool positioner Check valve Spool CONTENTS: Page -Technical data... 2/14 -Circuit mode... 2/14 -Dimensions... 3/14 -Dimensions... 4/14 -Lever mechanism...
More informationBW0511FP. ByWire Elements BW0511FP Flow Sharing Element Interface IBW0511
ywire Elements Flow Sharing Element Interface IW05 efore use, carefully read the GENERL INSTRUCTIONS FOR USE OF DIRECTIONL CONTROL VLVES Technical data Nominal flow Nominal pressure 35 l/min - P=8 bar
More informationAuxiliary valves. Lever. Spool positioner Check valve Spool
Auxiliary valves Lever Spool positioner Check valve Spool CONTENTS: Page -Technical data... 1 -Dimensions RP80... 2 -Dimensions RP60... 3 -Lever mechanism... 4 -Spools/spool control... 5 -Inlet cover/outlet
More information6/2 WAY DIRECTIONAL VALVE KV (NG 6)
6/2 WAY DIRECTIONAL VALVE KV (NG 6) NG 6 Up to 350 bar [5 076 PSI] Up to 50 L/min [13.2 GPM] Plug-in connector for solenoids to ISO 4400. Threaded connections to ISO 9974 (Metric), ISO 1179 (BSPP/Gas),
More informationPilot-Operated Directional Control Valves Series D3 - D11
Catalogue HY11-500/UK Characteristics The D31, D41, D81, D91 and D111 are electrical controlled 4/3 or 4/ way directional control valves. The valves are pilot-operated by an NG6 valve. Pressure and flow
More informationContents. Directional Control Valve 3 Series CV 452. Page 3-4. General Information. Page 5. Technical data. Page 6. Performance Curves.
Contents Page 3-4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 General Information Technical data Performance Curves Dimensions - Basics Valve Dimensions - LS Valve Secondary
More informationP.C. Priority Flow Control Valve Series J02D3. General Description
CV Catalog HY15-352/US General Description Needle Type, Compensated Regulator Valve. For additional information see Tips on pages 1-4. P.C. Priority Control Valve Series J2D3 Features Good adjustment from
More informationmechanical control valve
DF Working conditions This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm /s -- 46 cst viscosity at 4 C temperature. DF5 DF DF DF5 N. of available ways --3--6
More informationDirectional Control Valve Series 4D01 (DENISON)
Characteristics The Denison series 4D01 is a solenoid operated directional control valve size NG06 in -chamber design. It is direct operated by wet pin solenoids. The 4D01 is available with a Soft Shift
More informationSectional Directional Control Valve RSQ 240
Sectional Directional Control Valve RSQ 0 Key valve features RSQ 0 is a sectional open center valve, designed for max. operating pressures up to 50 bar and max. pump flows up to 00 l/min. It is available
More informationLOAD SENSE SECTIONS. Series 20. Directional Control Valves NEED NEW PIC VALVES STANDARD FEATURES SPECIFICATIONS
Directional Control Valves LOAD SENSE SECTIONS NEED NEW PIC Series 20 STANDARD FEATURES Control and reduced Dead Band (20I) and Tie Rod Kits SPECIFICATIONS Pressure Rating Foot Mounting Maximum Operating
More informationDirectional Control Valve Series D3W Soft Shift
Characteristics The D3W is a 3-chamber, electrically controlled 4/3 or 4/ way directional control valve. It is activated directly by solenoids with screwed in wet pin armature. The soft shifting of this
More information6/2 ways/positions flow diverters
6/2 ways/positions flow diverters RE 18302-07/07.12 Replaces: 12.09 1/8 L753... (VS311-VS312-VS315) Size 10 Series 00 Maximum operating pressure 310 bar [4500 psi] Maximum flow 140 l/min [36,98 gpm] Ports
More informationMonoblock directional control valves DL - Directional control valve
Monoblock directional control valves DL - Directional control valve DL Before use, carefully read the GENERAL INSRUCIONS FOR USE OF DIRECIONAL CONROL VALVES 398SMD008I00-06-2-208 DL echnical data Nominal
More informationSectional Directional Control Valve RS 220
Sectional Directional Control Valve RS 0 RS 0 is a sectional open center valve designed for max. operating pressures up to 00 bar and max. pump flows up to 0 l/min. Technical data Pressure and flow values*
More information6/2 ways/positions flow diverters L (VS151-VS152-VS155)
6/2 ways/positions flow diverters L721... (VS151-VS152-VS155) RE 1832-5 Edition: 2.216 Replaces: 5.214 Size 6 Series 1 Maximum operating pressure 31 bar (45 psi) Maximum flow 6 l/min (15.85 gpm) Ports
More informationHydro M t HYDRAULIC VALVES SN-4.
Hydro HYDRAULI VALVES A SRONG OMMIMEN O QUALIY Our concept is to sell and deliver the best quality of hydraulic valves, that fully meet our customer s rigorous requirements! o this end, our quality control
More informationSD2E-A3. Functional Description. 3/2 Way Solenoid Operated Directional Control Valves Spool Type HA /2013. Replaces HA /2012
3/2 Way Solenoid Operated Directional Control Valves Spool Type SD2E-A3 3/4-6 UNF p max 350 bar (5076 PSI) Q max 30 L/min (7.9 GPM) HA 404 /203 Replaces HA 404 07/202 Hardened and precision working parts
More informationSECTIONAL DIRECTIONAL VALVE HDS 30 SERIES. CROSS HYDRAULICS PTY LTD YELLOW CATALOGUE Page 3.106
CROSS HYDRAULICS PY LD YELLOW CAALOGUE Page 3.106 Material specification: Standard features: Optional features available: Symbols: P A/B H.P.C.O. RV P 1 1 Weight CROSS HYDRAULICS PY LD YELLOW CAALOGUE
More informationCommercial Shearing (Pty) Ltd THE WORLDWIDE PROGRAM OF VALVES ISO 9001
Commercial Shearing (Pty) Ltd THE WORLDWIDE PROGRAM OF VALVES ISO 9001 An Insight into Valve Technology CLEAN ROOM ASSEMBLY AND TEST A major investment has been made in a clean-room assembly and test environment.
More information6 to14/2 ways/positions bankable flow diverters flangeable
6 to14/2 ways/positions bankable flow diverters flangeable RE 18302-10/07.12 Replaces: 12.09 1/8 L745... (VS281F-VS285F-VS286F-VS287F-VS289F) Size 10 Series 00 Maximum operating pressure 310 bar [4500
More informationGeneral Specifications DRV DRV-Exm DRV-Exd
direct operated, 3-way pressure reducing valve Q max = 8 l/min pressure range = - 5 bar body stainless steel (optional) Description The proportional pressure reducing valve (3-way function) is used to
More informationPilot Operated Directional Control Valves Series D31DW, D41VW - D111VW
Characteristics The D31, D41, D81, D91 and D111 are electrically controlled 4/3 or 4/ way directional control valves. The valves are pilot operated by an NG6 valve. Pressure and flow of the pilot oil have
More informationPost-Compensated Proportional Valve CV2000LS
www.nimco-controls.com Post-Compensated Proportional Valve CV2000LS Smart Solutions... for the Future Contents Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 Page 16
More informationDFE. solenoid control monoblock valve. Content. Working conditions Hydraulic circuit DFE052. Dimensional data Ordering codes...
DFE Content Working conditions... 54 Hydraulic circuit... 55 DFE52 DFE1 DFE2 Dimensional data... 6 Ordering codes... 64 Positioner kits... 67 Solenoid parts... 68 Dimensional data... 69 Ordering codes...
More information3/2 ways/positions flow diverters L (VS91-VS92-VS95)
3/2 ways/positions flow diverters L706... (VS91-VS92-VS95) RE 18302-03 Edition: 04.2016 Replaces: 02.2016 Size 12 Series 00 Maximum operating pressure 310 bar (4500 psi) Maximum flow 140 l/min (36.98 gpm)
More informationContents. Directional Control Valve 2 Series EPCV 452. Page 3. General Information. Page 4-5. Technical data. Page 6. Performance Curves.
Contents Page 3 Page 4-5 Page 6 Page 7 Page 8 Page 9 General Information Technical data Performance Curves Dimensions : Hydraulic Valve and Accumulator Hydraulic Schematics Order Code Directional Control
More informationPilot Operated Directional Control Valves Series D31DW, D31NW, D*1VW
Characteristics The pilot operated valves are available in 4 sizes: D31DW NG10 (standard) D31NW NG10 (high flow) D41VW NG16 D81VW NG5 (for port diameter up to 6 mm) D91VW NG5 (for port diameter up to 3
More informationDFE10. solenoid control monoblock valve. Ordering codes. Description example : Diverter valve DFE10/3 A 18 ES - W VDC - SAE - <CVN>
DFE1 Ordering codes Description example : Diverter valve DFE1/3 18 ES - W 22-12VDC - SE - 1. 4. 5. 3. 5. 2. Valve is supplied painted as standard, with one coat of rimer black antirust paint II 5.
More information6/2 ways/positions flow diverters
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service 6/2 ways/positions flow diverters RE 18302-07/12.09 1/8 L753... (VS311-VS312-VS315) Size 10 Series 00
More information6 to14/2 ways/positions bankable flow diverters flangeable
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service 6 to14/2 ways/positions bankable flow diverters flangeable RE 18302-10/12.09 1/8 L745... (VS281F-VS285F-VS286F-VS287F-VS289F)
More information6/2 ways/positions flow diverters
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service 6/2 ways/positions flow diverters RE 1832-5/12.9 1/8 L721... (VS151-VS152-VS155) Size 6 Series 1 Maximum
More informationMonobloc and Sectional Directional Control Valves
Monobloc and Sectional Directional Control Valves motion and progress 1/220 6 Monobloc directional control valves Contents 6.1 General specifications 66 6.2 Dimensional data 67 6.3 Performances curves
More informationDirectional Control Valve Series D3W (Parker), 4D02 (Denison)
Characteristics Series D3W (Parker), 4D0 (Denison) The direct operated directional control valve size NG10 is available with both Parker (series D3W) and Denison (series 4D0) model codes. Both series are
More informationContents. Directional Control Valve 2 Series CV 300
Contents Page 3 General Information Page 4 Technical data Page 5 Dimensions Page 6 Secondary Valves Page 7 Cylinder port mounted secondary valves Page8 Spool - Control characteristics Page 9-10 Spool Controls
More informationWalvoil 2/2, 3/2, 6/2, 8/3 Wegeventile, elektromagnetisch Gruppe mehr als Qualität
2/2, 3/2, 6/2, 8/3 Wegeventile, elektromagnetisch mehr als Qualität DFE Contents Working conditions 48 Hydraulic circuit 49 DFE52 DFE1 DFE2 Dimensional data 53 Ordering codes 56 Positioner kits 59 Solenoid
More information6 to14/2 ways/positions bankable flow diverters flangeable
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service 6 to14/2 ways/positions bankable flow diverters flangeable RE 18302-09/12.09 1/10 L732... (VS241F-VS245F-VS246F-VS247F)
More informationHYDRAULIC CONTROL VALVES
HYDRAULIC VALVES SECTION 3A HYDRAULIC CONTROL VALVES MONOBLOCK DIRECTIONAL CONTROL VALVES...71 SLICE DIRECTIONAL CONTROL VALVES...73 HANDLEVERS...76 S additions for valves...76 VALVE CONTROL KITS additions
More informationHYDRAULICS VINCKE DIRECTIONAL CONTROL VALVES
VINCKE DIRECTIONAL CONTROL VALVES TECH-DCV200.1 index 3 link to your page / link a su página Monoblock hydraulic distributors Monoblock hydraulic distributors 35 liters 3 P35 Monoblock hydraulic directional
More information3/2 ways/positions flow diverters
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service 3/2 ways/positions flow diverters RE 18302-02/12.09 1/8 L705... (VS81-VS82-VS84-VS85) Size 6 Series 00
More informationFunctional Description
4/2 Way Solenoid Operated Directional Control Valves Spool SD2E-A4 Type 3/4-16 UNF p max 350 bar (5076 PSI) Q max 30 L/min (7.9 GPM) 01/2005 4/2 Way cartridge valves solenoid operated spool directed Manual
More informationSDH Series. Monoblock and Sectional directional valves
SDH Series Monoblock and Sectional directional valves Additional information his catalogue shows the product in the most standard configurations. lease contact Sales Dpt. for more detailed information
More informationLine mounting From SAE08 to SAE16 cavities. 15 l/min (3.9 US gpm) from -20 C (-4 F) to 80 C (176 F) from -20 C (-4 F) to 100 C (212 F)
PU.. type flow control pressure compensated valves - ways Line mounting From SE to SE cavities Technical specifications and diagrams are measured with mineral oil of cst viscosity at C ( F) temperature.
More informationLOGIC ELEMENTS SERIES 10 LC* LP* /103 ED CARTRIDGE VALVES ISO DIN COVERS FOR CARTRIDGE VALVES ND
48 900/103 ED LC* LP* LOGIC ELEMENTS CARTRIDGE VALVES ISO 7368 - DIN 24342 COVERS FOR CARTRIDGE VALVES ND 16-25-32-40-50 p max 420 bar Q max (see performance ratings table) OPERATING PRINCIPLE Logic elements
More information» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries
HYDRAULIC HW APPLICATION» Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries» Grass cutting machinery etc. CONTENTS
More informationPressure Compensator Valves Series R5P (SAE Flange Mounted) General Description. Features
Technical Information General Description Series R5P direct operated, 3-way pressure compensators can be combined with any type of fixed or adjustable flow resistor (throttle) to provide a load compensated
More informationGPM PSI LPM BAR MODEL CAVITY PAGE IF-S3A special IF-S3D special IG-S4A special 198
Transmission & Brake Spool Valves Screw-in style GPM PSI LPM BAR MODEL CAVITY PAGE 2 1000 8 70 TC-S3A 5/8-18 186 6 1000 23 70 TF-S3A 7/8-14 188 6 1000 23 70 TF-S3D 7/8-14 190 5 1000 20 70 TG-S4A 7/8-14
More informationSD3E-B2. Functional Description. 2/2 Way Solenoid Operated Directional Control Valves Poppet Type HA /2012. Replaces HA /2010
/ Way Solenoid Operated Directional Control Valves Poppet Type SD3E-B 7/8-4 UNF p max 40 bar (609 PSI) Q max 75 L/min (9.8 GPM) H 4063 7/0 Replaces H 4063 0/00 / way cartridge valves solenoid operated
More informationVariable displacement axial piston pumps
Variable displacement axial piston pumps SVP series GENERAL INFORMATIONS Variable displacement axial piston pump swash plate design for open circuit-flow sharing control valve. The pump has been designed
More informationSDE030 SDE060. Directional control valves with direct acting solenoid
SDE SDE Directional control valves with direct acting solenoid SDE-SDE General informations Simple, compact and heavy duty designed sectional valves from to sections. SDE luminium alloy inlet sections,
More information4/3 Proportional directional valve elements L85P5 with proportional (EDC-IP) hydraulic control and flow sharing control (LUDV concept) PATENT PENDING
/ Proportional directional valve elements L8P with proportional (EDC-IP) hydraulic control and flow sharing control (LUDV concept) PATENT PENDING L8P (EDC-IP) RE 8- Edition:.6 Replaces: 7. Size 6 Series
More informationDual Axis Hydraulic Joystick Series JH4
Dual Axis Hydraulic Joystick Series JH4 03.JH4-0911 Index of content: Description & technical data: Page 3 Hydraulic circuit diagrams (joysticks): Page 4 Typical hydraulic circuit diagrams (system): Page
More informationunrestricted; preferably with coil at bottom (auto. air bleed) 12 or 24 Volt DC from an electronic controller Deutsch plug - IP67
3 Technical data General characteristics Design Flow direction Seals De-energized position Mounting attitude Description, value, unit line mounting P A controlled P R surplus flow discharge (models shown
More informationSECTIONAL DIRECTIONAL VALVE HDS 20 SERIES. CROSS HYDRAULICS PTY LTD YELLOW CATALOGUE Page 3.84
CROSS HYDRAULICS PTY LTD YELLOW CATALOGUE Page 3.84 Material specification: Standard features: Optional features available: Symbols: P T A/B H.P.C.O. RV P 1 T 1 Weight CROSS HYDRAULICS PTY LTD YELLOW CATALOGUE
More informationHYDRAULIC PILOT CONTROL UNIT OF SANDWICH PLATE DESIGN
01 /10 2.2 HYDRULIC PILOT CONTROL UNIT OF SNDWICH PLTE DESIGN Type: H*-2TH6 Benefits: Progressive, sensitive control Precise and play-free control characteristics Low actuation force at the lever Rust-free
More informationChapter 10: Valves for Pipe Mounting
Contents Chapter : Valves for Pipe Mounting Series Description Size Body Page DIN / ISO 1/8 1/4 3/8 1/2 3/4 1 1¼ 1½ 2 L-port T-port Pressure valves, manual operation R4V R4R Pressure relief function Pressure
More informationSafety & Shut-off Blocks
Safety & Shut-off Blocks Description HYDAC safety and shut-off blocks are designed to protect, shut-off, and discharge hydraulic accumulators or user units. The compact design simplifies the hydraulic
More informationProportional Directional Control Cartridge Valves: PSV10-34 & PSV12-34
Control Cartridge Valves: PSV10-34 & PSV12-34 SCHEMATIC PRESSURE* FLOW CAVITY COIL Page 2 PSV10-34-02 250 BAR 3600 PSI 22 LPM 6 GPM SDC10-4 M16-26W R16-20W Page 4 PSV12-34-02 260 BAR 3770 PSI 50 LPM 13
More information6 to 12/2 ways/positions bankable flow diverters flangeable
6 to 12/2 ways/positions bankable flow diverters flangeable RE 18302-08/07.12 Replaces: 12.09 1/8 L711... (VS120F-VS125F) Size 4 Series 00 Maximum operating pressure 310 bar [4500 psi] Maximum flow 20
More information6/2 ways/positions flow diverters L (VS120-VS125-VS129)
6/2 ways/positions flow diverters L710... VS120-VS125-VS129) RE 18302-04 Edition: 05.2014 Replaces: 07.12 Size 4 Series 00 Maximum operating pressure 310 bar 4500 psi) Maximum flow 25 l/min 6.6 gpm) Ports
More informationPilot Operated Directional Control Valves Series D1VP, D3DP, D4P, D9P, D11P
Characteristics Series D1VP, D3DP, D4P, D9P, D11P The D1VP is a hydraulically controlled 4/3 or 4/ way directional control valve. The valve can be operated either by the pilot ports X and Y via the subplate
More informationVINCKE HYDRAULIC PUMPS
: VNK BA10VS 21 Variable displacement axial piston pump of swashplate design for hydraulic open circuit systems. Flow is proportional to drive speed and displacement. It can be infinitely varied by adjustment
More informationSD2E-A4. Functional Description. 4/2 Way Solenoid Operated Directional Control Valves Spool Type HA /2014. Replaces HA /2013
/ Way Solenoid Operated Directional Control Valves Spool Type SDE- /-6 UNF p max 50 bar (5076 PSI) Q max 0 L/min (7.9 GPM) 07/0 Replaces 0/0 Hardened precision working parts High flow capacity High transmitted
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump HY-TRANS THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 501 / 1009 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HY-TRANS THE PRODUCTION LINE OF HANSA-TMP Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 851 / 0813 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES THE PRODUCTION LINE OF HANSA-TMP Variable Displacement Closed Loop System CONTENTS General Information... Order Code... Manual Control
More informationPilot control unit with end position lock for the remote control of directional valves
Pilot control unit with end position lock for the remote control of directional valves RE 64 553/02.07 1/12 Replaces : 05.05 Type 4THF6 or 5THF6 Series 2X Contents Functional description, section, symbol
More informationDirectional Seat Valve Series D4S (Denison)
Characteristics Seat valves series D4S are designed for directional control functions. A large variety of poppets, springs and covers - including shuttle valves, stroke limiters, solenoid valves (VV01)
More informationDirectional valve elements L808103P (ED4-PT1) of Tank unloaded excess flow. RE Edition: Replaces:
Directional valve elements L80810P with proportional (ED4-PT1) control of Tank unloaded excess flow L80810P (ED4-PT1) RE 1801-1 Edition: 09.2016 Replaces: 07.12 01.2016 Size 6 Series 00 Maximum operating
More informationD05 Directional Control Valves
Engineering D05 Directional Control Valves WFDG4S*4-01, 60 Design Wet Armature Solenoid Operated Max Pressure up to 248 Bar (3600 psi) Same Day Shipments www.fluidynefp.com Table of Contents Basic Characteristicts...2
More informationDENISON HYDRAULICS High Flow Seat Valve Cartridges CEHFE, C1C
DENISON HYDRAULICS High Flow Seat Valve Cartridges CEHFE, C1C 2/2-Way Function / Cavity conform to ISO 7368 (DIN 24342) Publ. 7 EN 5060 A FEATURES, DESCRIPTION FEATURES x High flow cartridges give highest
More informationV050 SERIES DIRECTIONAL CONTROL VALVE
V5 SERIES DIRECTIONAL CONTROL VALVE TAKE CONTROL Take control with Muncie Power Products V5 directional control valve. The V5 is constructed with high-grade iron castings and nickel-plated spools for use
More informationCLS180 Proportional Load Sensing Mobile Valve
Mobile valves Proportional Load Sensing, Model CLS180 350 bar 180 L/min Up to 10 sections Eaton Pro-FX TM Ready CLS180 Proportional Load Sensing Mobile Valve Overhaul manual / Trouble shooting guide Contents
More informationDIRECTIONAL CONTROL VALVES CETOP3
DIRECTIONAL CONTROL VALVES CETOP3 GENERAL DESCRIPTION RH0...1-...F... Document: DCVC3-1-Aug 2013 4/3- and 4/2- way directional control valves with solenoid operation, heavy duty construction RH0...1-...F...
More informationVickers Pressure Relief Solenoid Operated, Two-Stage Directional Control Valve DG5S4-02 Flows to 115 l/min (30 USgpm) Pressure to 210 bar (3000 psi)
Vickers Pressure Relief Solenoid Operated, Two-Stage Directional Control Valve DG5S4-02 Flows to 115 l/min (30 USgpm) Pressure to 210 bar (3000 psi) Revised 2/93 GB C 2037 Table of Contents Model Code...................................................................................................
More informationSolenoid valve VDHT standard BSP (British Standard Pipe)
Technical data sheet standard BSP (British Standard Pipe) danfoss.high-pressurepumps.com 521B1166 / DKCFN.PD.043.A1.02 Index 3. Picture Overview 4. Features 5. Technical data 6. Technical data 7. General
More informationFlow sharing control block in mono block / sandwich plate design M6-15
Flow sharing control block in mono block / sandwich plate design M6-15 RE 64321 Edition: 01.2015 Replaces: 05.2012 Size 15 Series 3X Maximum operating pressure on pump side 350 bar on consumer side 420
More informationDirectional Control Valve Series D1VW
Characteristics The NG6 directional control valve series D1VW provides high functional limits up to 8 l/min in combination with a very low, energy-saving pressure drop. A wide variety of spool options
More informationElectric Proportional Pressure Reducing Valves Series ERP 03.ERP
Electric roportional ressure Reducing Valves Series ER 03.ER - 0912 Electric proportional pressure reducing valves SERIES ER Index of content: Description and main features: age 3 echnical data: age 4
More informationAPM212 Gear Motors, including Fan Drive Gear Motors
Gear Motors, including Fan Drive Gear Motors Standard and Low Noise series Reference: 2-P-991231-EN-3 Issue: 11.217 1/56 Contents Page 1 General information... 3 1.1 External gear motors for general use...
More informationHYDRAULIC MOTORS MLHH
HYDRAULIC APPLICATION» Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries» Mining machinery etc. CONTENTS Specification
More informationContents. Directional Control Valve 2 Series CV Unibody. Page 3-4. General Information. Page 5. Technical data. Page 6. Performance Curves
Contents Page 3-4 Page 5 Page 6 Page 7 Page 8 Page 9 Page 10 Page 11-12 Page 13 Page 14 Page 15 General Information Technical data Performance Curves Dimensions - Basic Valve Dimensions - Unibody Secondary
More informationType of operation Depending on requirement either one or two dry DC-solenoid,
Features Leakage free High availability 100% duty cycle Porting NG 6 according to DIN 24340 Positive overlap Function and design The seated valves are direct operated. Depending on the desired control
More informationPressure Control Valves
Control Valves DR8- Reducing/Relieving, Direct Acting, Spool Type 4 gpm (5 l/min) 6 psi (4 bar) Description A screw-in cartridge, direct acting, spool type, pressure reducing/relieving valve with internal
More informationMonoblock Directional Control Valve RM 230
Monoblock Directional Control Valve RM 230 Key valve features RM 230 light is a monoblock valve, designed for max. operating pressures up to 3,000 psi (210 bar) and typ. pump flows up to 20 gpm (70 Lpm).
More information6 to 12/2 ways/positions bankable flow diverters flangeable
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics Service 6 to 12/2 ways/positions bankable flow diverters flangeable RE 18302-08/12.09 1/10 L711... (VS120F-VS125F)
More informationDIRECTIONAL CONTROL VALVES CETOP3
DIRECTIONAL CONTROL VALVES CETOP3 CONTENTS: RH06...1 - electrical control... RH06...2 - hydraulic control... Page 1/17...7/17 8/17...9/17 RH06...4 - mechanical control RH06...6 - pneumatic control......
More informationV250 SERIES DIRECTIONAL CONTROL VALVES
V SERIES DIRECTIONAL CONTROL VALVES TAKE CONTROL OF YOUR HYDRAULICS Take control with Muncie Power Products V directional control valve. The V is constructed with high-grade iron castings and nickel-plated
More informationAP212HP Cast Iron Gear Pumps
Cast Iron Gear Pumps Standard and Low Noise series Reference: 200-P-991236-EN-01 Issue: 09.2016 1/56 Contents Page 1 General information... 5 1.1 External gear pumps components... 6 1.2 Technical data...
More informationStand alone 4/3, 4/2 direct acting directional valve LF2_1 (LC2F-DZ)
Stand alone 4/3, 4/2 direct acting directional valve LF2_1 (LC2F-DZ) RE 18305-03 Edition: 02.2016 Replaces: 07.12 07.2012 Size 10 Series 00 Maximum operating pressure 250 bar (3600 psi) Maximum flow 90
More information