Models MSR-2424/MSR-3624

Size: px

Start display at page:

Download "Models MSR-2424/MSR-3624"

Everett McDaniel
6 years ago
Views:

1 Molded one-piece construction for light weight and easy handling. Supplied with Wedge-Lok seal, integral drain and chrome strainer. Models MSR-2424/MSR-3624 Molded Mop Receptors Furnish and install molded Mop Receptor Model MSR-2424 / MSR-3624 (specify) as manufactured by Products o. Molding will be done under heat and pressure using matched metal dies. The unit will be one piece with no seams. Shoulders will be no less than wide and 9½" inside. Receptor will have ribbed underbody and integral drain providing for a no-caulked connection to a 2" or 3" S pipe (specify drain size). rain grid will be 18-gauge stainless steel, flat type, #430. Models MSR-2424/MSR-3624 Molded mop sinks are supplied with Wedge-Lok seal for use on S pipe only. 1½" 5½" 10" 6" 1¼" Model WT. MSR " 24" 50 MSR " 24" 18" 18" 72 Standards: I..P. M.O. International ssociation of Plumbing and Mechanical Officials File No NSI merican National Standards Institute - Z HU/FH National UN-73. S TST Warnock Hersey Listed: N / S N / S

Model 5 Terrazzo Mop Receptor Model 5 Island Shown: Model 5 Furnish and install mop receptor as manufactured by Products o. Shoulder shall be not less than 8" high inside and not less than 1l" wide.

2 Model 5 Terrazzo Mop Receptor Model 5 Island Shown: Model 5 Furnish and install mop receptor as manufactured by Products o. Shoulder shall be not less than 8" high inside and not less than 1l" wide. rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland cement to produce a compressive strength of not less than 3000 PSI, seven days after casting. Terrazzo surface shall be ground and polished with all air holes and/or pits to be grouted and excess removed and sealed to resist stains and moisture. Receptor will be reinforced with 16 gauge wire. Stainless steel grid standard. Terrazzo is not designed to be 10" Specify 2 or 3 drain size (3 standard). HT. WT. 24" 24" 10" imensions may vary ± 1 /4" inch. Please check unit before installation.

Models 10/20/30/40 Models 10 / 20 / 30 / 40 Furnish and install mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide.

3 Models 10/20/30/40 Models 10 / 20 / 30 / 40 Furnish and install mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide. (For high wall model specify: Not less than 9" high inside and not less than 1¾" wide ). Galvanized, bonderized steel flange will extend at least one inch above shoulder on one, two or three sides for installation against stud wall (specify choice). rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland Shown: Model 40 Model 10 Model 20 Model 30 LH Model 30 RH Model 40 Terrazzo is not designed to be 6"or Specify 6" or height. Specify Right Hand or Left Hand where applicable. imensions may vary ± ¼. Please check unit before installation. HT. WT. 24" 24" 6" " 6" 16" 16" 16" " 6" 18" 18" " 6" 18" 18" 18" " " 16" 16" 16" " 18" 18" " 18" 18" 18" 525

Shown: Model 50 Stainless Steel aps: Model 50 Model 60 LH Model 60 RH Model 70 Models 50 / 60 / 70 Furnish and install mop receptor as manufactured by Products o.

4 Shown: Model 50 Stainless Steel aps: Model 50 Model 60 LH Model 60 RH Model 70 Models 50 / 60 / 70 Furnish and install mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide. (For high wall model specify: Not less than 9" high inside and not less than 1¾" wide ). Galvanized, bonderized steel flange will extend at least one inch above shoulder on one, two or three sides for installation against stud wall (specify choice). Stainless steel protective cap to be cast integral on exposed side(s) (as specified). rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland Models 50/60/70 6"or Terrazzo is not designed to be imensions may vary ± ¼. Please check unit before installation. HT. WT. 24" 24" 6" " 6" 16" 16" 16" " 6" 18" 18" " 6" 18" 18" 18" " " 16" 16" 16" " 18" 18" " 18" 18" 18" 525 Specify 6" or height. Specify Right Hand or Left Hand where applicable.

Models 80/81/82/83 Models 80 / 81 / 82 / 83 Furnish and install mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide.

5 Models 80/81/82/83 Models 80 / 81 / 82 / 83 Furnish and install mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide. (For high wall model specify: Not less than 9" high inside and not less than 1¾" wide ). Galvanized, bonderized steel flange will extend at least one inch above shoulder on one, two or three sides for installation against stud wall (specify choice). Stainless steel protective cap to be cast integral on all four exposed sides. rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland Stainless Steel aps: Shown: Model 81 Model 80 Model 81 Model 82 LH Model 82 RH Model 83 Terrazzo is not designed to be 6"or Specify 6" or height. Specify Right Hand or Left Hand where applicable. imensions may vary ± ¼. Please check unit before installation. HT. WT. 24" 24" 6" " 6" 16" 16" 16" " 6" 18" 18" " 6" 18" 18" 18" " " 16" 16" 16" " 18" 18" " 18" 18" 18" 525

Shown: Model 87 Stainless Steel aps: Model 85 Model 86 Model 87 Models 85 / 86 / 87 NO NGL Furnish and install mop receptor as manufactured by Products o.

6 Shown: Model 87 Stainless Steel aps: Model 85 Model 86 Model 87 Models 85 / 86 / 87 NO NGL Furnish and install mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide. (For high wall model specify: Not less than 9" high inside and not less than 1¾" wide ). Galvanized, bonderized steel flange will extend at least one inch above shoulder on one, two or three sides for installation against stud wall (specify choice). Stainless steel protective cap to be cast integral on all four exposed sides. rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland cement to produce a compressive strength of not less than 3000 PSI, seven days after casting. Terrazzo surface shall be ground and polished with all air holes and/or pits to be grouted and excess removed and sealed to resist stains and moisture. Receptor will be reinforced with 16 gauge wire. Models 85/86/87 NO NGL 6"or Terrazzo is not designed to be imensions may vary ± ¼". Please check unit before installation. Model WT " 24" " 16" 16" 16" " 18" 18" 18" " " 32" 16" 16" 16" " 18" 18" 18" " " 16" 16" 16" " 18" 18" 18" 490

7 Models 90/91/92 Models 90 / 91 / 92 rop Front Furnish and install square drop front mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide. Galvanized, bonderized steel flange will extend at least one inch above shoulder on one, two or three sides for installation against stud wall (specify choice). Stainless steel protective cap to be cast integral on drop side (Model 91 and 92 only). rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland Terrazzo is not designed to be Model 90 Model 91 Model 92 Stainless Steel aps: Shown: Model 90 imensions may vary ± ¼". Please check unit before installation. Model WT " 24" " 32" 16" 16" 16" " 24" 18" 18" " 36" 18" 18" 18" " 24" " 32" 16" 16" 16" " 24" 18" 18" " 36" 18" 18" 18" " 24" " 32" 16" 16" " 24" 18" 18" " 36" 18 18" 18" 465 6"

Model 95 Model 96 Shown: Model 95 Stainless Steel aps: Models 95 / 96 NO NGL rop Front Furnish and install neo angle drop front mop receptor as manufactured by Products o.

8 Model 95 Model 96 Shown: Model 95 Stainless Steel aps: Models 95 / 96 NO NGL rop Front Furnish and install neo angle drop front mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide. Galvanized, bonderized steel flange will extend at least one inch above shoulder on one, two or three sides for installation against stud wall (specify choice). Stainless steel protective cap to be cast integral on drop front (Model 96 only). rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland Models 95/96 6" Terrazzo is not designed to be imensions may vary ± ¼". Please check unit before installation. Model WT " 24" " 16" 16" 16" " 18" 18" 18" " " 32" 16" 16" 16" " 18" 18" 18" 465

Models 97 Models 97 Half Round Furnish and install half round mop receptor as manufactured by Products o. Shoulder shall be not less than 9" high inside and not less than 1¾" wide.

9 Models 97 Models 97 Half Round Furnish and install half round mop receptor as manufactured by Products o. Shoulder shall be not less than 9" high inside and not less than 1¾" wide. Galvanized, bonderized steel flange will extend at least one inch above shoulder on one, two or three sides for installation against stud wall (specify choice). rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland 28" 16" Shown: Model 97 28" Terrazzo is not designed to be imensions may vary ± 1 /4 inch. Please check unit before installation.

Model 99 Half Round rop Front Model 99 28" Stainless Steel aps: 16" Shown: Model 99 Furnish and install half round drop front mop receptor as manufactured by Products o.

10 Model 99 Half Round rop Front Model 99 28" Stainless Steel aps: 16" Shown: Model 99 Furnish and install half round drop front mop receptor as manufactured by Products o. Shoulder shall be not less than 4" high inside and not less than 1¾" wide. Galvanized, bonderized steel flange will extend at least one inch above shoulder on one, two or three sides for installation against stud wall (specify choice). Stainless steel protective cap to be cast integral on drop front. rain body shall be brass, cast integral and shall provide for a non-caulked connection (lead caulked optional) not less than one inch deep to a two or three inch pipe (specify 2" or 3"). Mop sinks with 3" drains are supplied with a rubber seal for use on S, PV or steel pipe. Receptor shall be manufactured of tan and white marble chips cast in white portland cement to produce a compressive strength of not less than 3000 PSI, seven days after casting. Terrazzo surface shall be ground and polished with all air holes and/or pits to be grouted and excess removed and sealed to resist stains and moisture. Receptor will be reinforced with 16 gauge wire. 28" Terrazzo is not designed to be 6" Weight: 310 lbs. imensions may vary ± 1 /4 inch. Please check unit before installation.

11 Mop Receptor ccessories Molded and Terrazzo Mop Receptors ccessories (1) MR-370 s Hose, 5' long with clamp. (2) MR-371 Speakman Faucet with vacuum braker, double stops and bucket hook with brace. U.S. made. (3) MR-372 Mop hanger with 3 clamps. (4) MR-373 Stainless Steel rim guard, #304, 20 gauge, 24" or 36". Specify length and one (1), two (2), three (3) or four (4) each. (available on Molded Mop Sinks only) (5) MR-374 Wedge-Lok Seal, specify 2" or 3". (available on Molded Mop Sinks only) (6) MR-375 Flat strainer, chrome. (available on Molded Mop Sinks only) (7) MR-376 ome strainer, chrome. (available on Molded Mop Sinks only) (8) MR-377 Two (2) each 24" panels or Two (2) each 32" panels or One (1) 24" panel and One (1) 36" panel. Speakman is a Registered Trademark of Speakman o. 5 4

Segment Name: CAST IRON 22X18 SERVICE SINK

Segment Name: CAST IRON 22X18 SERVICE SINK Segment Code: Features KOHLER cast iron Acid resistant enamel finish Single compartment With rim guard 22-1/4 (56.5 cm) x 18-1/4 (46.4 cm), or 24 (61 cm) x 20-1/4