King Dome. user manual
|
|
- Amanda Gregory
- 5 years ago
- Views:
Transcription
1 King Dome user manual
2 INTRODUCTION The Martin King Dome is a light weight, inflatable transparent housing for protection of a luminaire from precipitation in temporary outdoor applications. It features a powerful fan that inflates the envelope and cools the lighting fixture, and a pressure-activated switch that automatically cuts off power to the luminaire in the event of deflation. COMPATIBLE LUMINAIRES Use the King Dome only with a luminaire meeting the criteria listed on the back cover. SAFETY PRECAUTIONS Warning! This product is for professional use only. Always ground (earth) the King Dome electrically. Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault protection. Do not use the King Dome with luminaires that consume more than 1200 watts of power. Do not cover or paint the transparent envelope. Do not push, poke, or press the King Dome once inflated. Do not lean or sit on the King Dome. Do not use the King Dome in very dusty areas. Do not block the air vents. Do not install or operate the King Dome in heavy winds (over 17 m/s or 37 M.P.H.). Keep the King Dome away from small children when not in use.
3 OPERATION To inflate the King Dome 1 Place the base of the dome on a level surface. 2 Center the luminaire on the King Dome base. Verify that no part of the luminaire can extend over the edge of the base during operation. 3 If you have not already done so, set the fixture operating mode and control address. 4 Connect the luminaire s AC power lead to the 230 V (blue) or 110 V (yellow) outlet on the King Dome base. 5 Lead the data cables through an air vent and connect them to the luminaire. 6 If the luminaire has a power switch, set it to the ON position. (Fixture power is disabled until the King Dome is fully inflated.) 7 Fit the inflatable plastic dome over the base so that the Velcro strip on the dome is right next to, and parallel with, the Velco strip on the base. Secure the plastic dome by wrapping the double Velco tape over both Velcro strips. 8 Apply power to the King Dome. The King Dome automatically inflates when power is applied. Power to the fixture is enabled as soon as the King Dome is fully inflated, To deflate the King Dome 1 Extinguish the lamp by sending a lamp-off command from the controller. 2 Allow the luminaire to cool for at least 10 minutes, then disconnect the King Dome from power. 3 Remove the double band of Velco that secures the plastic dome to the base. 4 Carefully fold and store the plastic dome. 5 Disconnect and remove the luminaire. 6 Remove the data cables and put everything away.
4 SPECIFICATIONS PHYSICAL Base diameter: cm (31.5 in) Base height: cm (9,9 in) Base weight: kg (1.3 lbs) Long envelope height: cm (63.0 in) Short envelope height: cm (31.5 in) COMPATIBLE LUMINAIRES Maximum vertical dimension: up to envelope height Maximum base dimensions: x 48 cm (21.2 x 18.9 in) Maximum weight: kg (143 lbs) Maximum power consumption: W ENVIRONMENTAL Maximum ambient temperature (Ta): C (77 F) Maximum wind speed: m/s (37 M.P.H.) Maximum noise: db at 1 m (39 in) AC SUPPLY EU model: V / 50 Hz with female connection for fixture (2P+T) US model: V / 60 H with female connection for fixture (2P+T) CONSTRUCTION Base: mm ABS plastic Base finish: black, integral color Envelope: transparent 200 my non-flammable PVC film Protection factor: IP 44 Martin Professional A/S Olof Palmes Allé Aarhus N Denmark Phone: Internet:
5 OUTDOOR PROTECTION DOME
6 Assembly Procedure Triangle notch points down Reinforcement plate L-shaped lip Leave top and bottom holes free Assembling the side plates 1. Remove the parts from the packing boxes. 2. Assemble the plastic side plates. Stand 2 plates with the L-shaped lip pointing up. Fit the plates together with the ends overlapping. Place a metal reinforcing plate behind the joints with the notch pointing down. Start 6 self-tapping screws (M4 x 10 mm) in each joint, leaving the top and bottom holes free. Make sure these holes are lined up as you tighten the screws. 3. Place an assembled set of side plates on a level surface. Sealing the polycarbonate dome with silicone is recommended, but not absolutely necessary if total disassembly of the Dome is required. If sealing, cut 20 to 25 mm off the end of the sealant applicator tip. Apply a heavy bead (about 7 mm) of sealant in the corner of the L-shaped lip. 4. Line up the holes in the rim of the polycarbonate dome with the holes at the top of the side plates and set the dome on. Place rubber grommets at the 4 screw holes between the PN , Rev C Outdoor Protection Dome 2
7 dome and the side plates. Insert screws (M4 x 20 mm). From inside, put a washer and thumb nut on the screws and hand tighten. If the nuts are hard to start behind the reinforcing plates, the washers may be omitted. 5. To lengthen the Dome for use with the MAC 1200 or PAL 1200, place the upper section on an assembled set of side plates. Rotate the upper section so that the reinforcing plates are offset 1/4 turn from the reinforcing plates in the lower section. Insert M4 x 20 mm screws in the 4 holes. Place a washer and hex nut on each screw and tighten. Repeat to lengthen the Dome for use with the PAL There are two ways to lead the power and control cables into the bottom of the base: through the square hole or the smaller slot. For temporary installations, use the square hole for easier access. The slot may provide a more secure cable lead for permanent installation. If the slot is used, remove a side plate from the base assembly in order to pass the power and control cables through the slot. Feed the control cable up through the peanut-shaped ventilation hole to the top of the base section. 7. Reach inside the base and plug the power cable into the male power connector. This connector feeds power to the cooling fan as well as the socket on the base. 8. Mount the base in position. The Dome may be secured through 4 holes in the base. Make sure that the air vents are not obstructed and that air can circulate in and out. Do not locate the Dome in low spots where water can collect. 9. If the Dome is to be used with a PAL 1200, attach 2 ventilation-spacer bars, included, to the base of the PAL. Remove the 4 bolts indicated and place the bars on the base as shown, with the shorter length facing the front. Fasten each bar with 2 M6 x 35 mm Allen-head bolts. 10. Plug the fixture power cable into the base. Place the fixture on the base. Make sure the base ventilation holes are not blocked. 11. PAL 1200 Dome only: Orient the PAL so that the back of the fixture faces the square ventilation hole. 12. MAC 500/600 Dome only: Align the base of the MAC with the raised mounting plate. Lock the MAC to the base by inserting the quarter-turn fasteners into the MAC base and turning them a full quarter turn clockwise. 13. Remove the 4 screws - located every 90 degrees around the top - from the base. Place the upper section on the base. Rotate the upper section until the joints are offset 1/4 turn from the joints in the base. Replace the 4 screws and tighten. PN , Rev C Outdoor Protection Dome 3
8 Safety Precautions Do not place the Dome where water can build up. Always stand the Dome vertically with the clear plastic dome on top. The Dome is not designed to be used in any other position. Make sure the base air vents are not blocked. Do not paint or cover the Dome, or in any way block the light path. Always connect the Dome to mains power as specified on the serial number label. Use only undamaged cables rated for outdoor use. Do not disassemble the base. There are no user-serviceable parts inside. Specifications IP Rating:... IP 44 PAL 1200 Dome Power and Current: W, 0.7 A at 230 V/50 Hz MAC 1200 Dome Power and Current: W, 0.7 A at 230 V/50 Hz MAC 500/600 Dome Power and Current: W, 0.5 A at 230 V/50 Hz AC Voltage and Frequency: V, Hz Diameter: mm PAL 1200 Dome Height, Weight: mm, 55 kg MAC 1200 Dome Height, Weight: mm, 53 kg MAC 500/600 Dome Height, Weight: mm, 52.5 kg PN , Rev C Outdoor Protection Dome 4
D.fm Page 1 Wednesday, March 5, :21 PM Raptor user manual
Raptor user manual 1 mounting bracket 2 swivel lock 3 clamp hole 4 lamp access screws 5 air vents 2001-2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced,
More informationMeasurements are expressed in millimeters.
T-Rex user manual Measurements are expressed in millimeters. 1 Lamp access 2 Focus adjustment 3 Mounting bracket 4 Swivel locks 5 Clamp hole 6 Air vent 190 285 7 AC input & main fuse 8 Microphone 490 164
More informationC.fm Page 1 Thursday, February 21, :28 AM Raptor user manual
Raptor user manual 1 mounting bracket 2 swivel lock 3 clamp hole 4 lamp access screws 5 air vents 6 AC input & main fuse 7 cooling fan Thank you for selecting the Martin Raptor. This Martin lighting fixture
More informationPN R CHEVY CAMARO w/reverse Two panel Sequential LED Taillight kit installation guide. Kit Contents:
Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness, 48 2 LED extension
More informationPONTIAC FIREBIRD
1974-78 PONTIAC FIREBIRD Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 LED panel mount kits 6 rubber grommets 1 power wire 1 pigtail harness Kit 1 crimp terminal
More informationP/N Wheeler. user manual
P/N 35000068 Wheeler user manual 1998, 1999 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from
More informationCHEVY CAMARO Four panel Sequential LED Taillight kit installation guide
1978-81 CHEVY CAMARO Four panel Sequential LED Taillight kit installation guide Kit Contents: 4 LED panels 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED harnesses, 48 4 LED
More informationMania EF1 user manual
Mania EF1 user manual Measurements are expressed in millimeters. 290 142 312 Ø13 250 2003 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or
More informationCHEVY MONTE CARLO. Two Panel Sequential LED Tail Light Kit Installation Guide
1986-88 CHEVY MONTE CARLO Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire 1 pigtail harness Kit 1 crimp terminal Kit 1 adhesive tube
More informationSequential LED Tail Light Kit Installation Guide PN
Sequential LED Tail Light Kit Installation Guide 1969 DODGE DART PN 1200469 Please refer to Invoice for full warranty information DIGI-TAILS is not a licensed MOPAR product Note The LED boards are shipped
More informationFiberSource Q150. user manual P/N
FiberSource Q150 user manual P/N 510260 1997, 1998 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing
More informationSITRANS F. Ultrasonic Flowmeters. Hi-Precision Mounts. Operating Instructions. Answers for industry.
SITRANS F Ultrasonic Flowmeters Hi-Precision Mounts Operating Instructions Edition 12/2014 Answers for industry. Preliminary Instructions 1 Reflect Mount Mode 2 SITRANS F Ultrasonic Flowmeters Hi-Precision
More informationMania DC3 user manual
Mania DC3 user manual Measurements are expressed in millimeters. Ø13 310 160 215 340 290 2004 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form
More information1968 PLYMOUTH ROAD RUNNER
Sequential LED Tail Light Kit Installation Guide 1968 PLYMOUTH ROAD RUNNER PN 1200568 Please refer to Invoice for full warranty information DIGI-TAILS is not a licensed MOPAR product Note The LED boards
More informationA B C D E F. Tools Required (supplied by others)
Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)
More informationWARNING. Important Notice
CAL (Color AquaLuminator ) Light and Return Water Flow for Above Ground Pools Owners Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION
More informationPN CHEVY TRI-FIVE. Kit Contents: Four panel Sequential LED Taillight kit installation guide
Four panel Sequential LED Taillight kit installation guide Kit Contents: 2 tail light LED panels 2 tail light turn signal LED panels 1 rubber boot/sleeve kit 1 power wire with t-tap 1 driver side LED harness,
More informationCHEVY NOVA w/reverse Four Panel Sequential LED Taillight Kit Installation Guide
1970-72 CHEVY NOVA w/reverse Four Panel Sequential LED Taillight Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 (5 pin) 1 passenger
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More informationJEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market
1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter
More informationPN DODGE CORONET Two panel Sequential LED Taillight kit installation guide. Kit Contents:
1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationVECTRIX VX-2 SERVICE MANUAL. Version 1.0/May 2011 VECTRIX, LLC
www.vectrix.com CONTENTS SECTION A: Tools 1 Tools Needed SECTION B: Mechanical Parts 1 Front Fairing 2 Front Console Cover 3 Speedometer Cover 4 Front Vertical Panel Cover-Lower 5 Front Vertical Panel
More informationTwo panel Sequential LED Taillight kit installation guide
1970 CHEVELLE Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 2 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationProduct Innovation Award winner Architectural/Flood lighting. Exterior 400 Range. Exterior 400 Range
Product Innovation Award winner Architectural/Flood lighting Exterior 00 Range Exterior 00 Range Exterior 00 Range TM The ultimate toolbox for energy-efficient outdoor lighting designs, the Exterior 00
More informationA B C D E F. b.tools Required (supplied by others) 3/16" Drill Bit 3/8" Wrench Phillips Head Screwdriver
Page 1 of 13 5E.1 Parts List a. Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel with Motor Attached (B) (1) Rope Reel Cover (C) (1) Cover Drum (1) Cover
More informationAquaLuminator Light and Return Water Flow for Above Ground Pools Owner's Manual
AquaLuminator Light and Return Water Flow for Above Ground Pools Owner's Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION I. IMPORTANT
More informationM-8100EP. Installation Guide ENGINEERED PLASTIC MANIFOLD SERIES. Introduction. A. Assemble Manifold Components
Introduction The Pro Manifolds with Integrated adaptor are designed for use in Hydronic radiant panel heating and cooling applications. They are available in various sizes, configurations, and options
More informationBUICK SKYLARK/GS
Sequential LED Tail Light Kit Installation Guide 1970-72 BUICK SKYLARK/GS PN 1101170 Please refer to Invoice for full warranty information DIGI-TAILS is not a licensed GM product Note The LED boards are
More informationPFadvantage MF 6850/6855; Ideal 9080/9090
MF 6850/6855; Ideal 9080/9090 Note: Indented items indicate parts included in an Quantity by Model assembly listed above MF Ideal Part Name/Description Part Number 6850 6855 9080 9090 Instruction Kit MF
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
1 AQUALUMIN III NICHELESS POOL LIGHT INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationFord 6.0L Regulated Return Kit
2003-2007 Ford 6.0L Regulated Return Kit A. Passenger Rear Return B. Line (Longer w/ 1-90 fitting) C. Driver Rear Return Line (Shorter w/ 1-90 fitting) D. Fuel Return Line (2 female fittings) E. Passenger
More informationMAVERICK, PINTO. Two Panel Sequential LED Tail Light Kit Installation Guide
1970-77 MAVERICK, 71-76 PINTO Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side
More informationS-Drive Performance Trainer
S-Drive Performance Trainer SERVICE MANUAl Table of contents CHAPTER 1: Serial number location... 1 CHAPTER 2: Important Safety instructions 2.1 Read and Save These Instructions... 2 2.2 Before Getting
More informationEgo 01 Ego 02 Ego 03 Logo Projector user manual
Ego 01 Ego 02 Ego 03 Logo Projector user manual Measurements are expressed in millimeters. 324 305 150 248 2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced,
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
AQUALUMINATOR & AQL LIGHT AND RETURN WATER FLOW FOR ABOVE GROUND SWIMMING POOLS INSTALLATION AND USER'S GUIDE Contents SECTION I. IMPORTANT SAFETY INSTRUCTIONS... 2 SECTION II. LAMP HOUSING INSTALLATION...
More informationFORD MUSTANG. Two Panel Sequential LED Tail Light Kit Installation Guide
1967-68 FORD MUSTANG Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationFlex Tube. User guide
Flex Tube User guide CONTENTS INTRODUCTION...2 Welcome 2 Safety 2 INSTALLATION...3 Flex Tube orientation 3 Bending a Flex Tube 4 Cutting a Flex Tube 4 Connection and mounting kits 5 Feed cable kit 5 End
More informationCARM INTERNATIONAL TOWING MODULES
CARM INTERNATIONAL TOWING MODULES (TA100/200 Instructions Revision = 1) Each Towing Module (if ordered with Loom Pack) is shipped with: A/ These instructions B/ 1 x Towing Control Module C/ 1 x high current
More informationINSTALLATION & OWNER S MANUAL
INDUSTRIES, LLC. INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 40 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KGL4AS) This Curtis Cab is designed and manufactured for use only as
More informationOWNERS MANUAL. Gold Series
LUNAR OWNERS MANUAL Comfort Base Gold Series Contents Safety Information...3 What Is Included...6 Assembly - Base...7 Location of Controls - Remote...11 Operation - Main...11 Operation - Linking the Remote...12
More information2-row and All-row systems included.
Ag Leader Technology Cotton Picker Installation Installation Instructions for John Deere cotton picker models: 2-row and All-row systems included. IMPORTANT: Ensure the model numbers shown above correspond
More informationJOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP)
P. 1 of 5 JOHN DEERE GATOR SWITCH PANEL INSTRUCTIONS FITS 1GTRXUV2 AND 1GTRXUV4 CABS (p/n: 1XUVSP) Note: Harness Extension Kit Required for 4 Passenger (p/n: 1XUV4WHEK) This manual is the property of the
More informationM Installation Guide. PRECISION Manifold Series. Introduction. A. Assemble Manifold Components
Page 1 Introduction The M-8200 Precision Manifolds are designed for use in Hydronic radiant panel heating and cooling applications. They are available in various sizes, configurations, and options with
More information1970 DODGE CHALLENGER Four panel Sequential LED Taillight kit installation guide
1970 DODGE CHALLENGER Four panel Sequential LED Taillight kit installation guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED
More informationManifold Isolation Valves
300 N. Opdyke Rd. Introduction The Stainless Manifolds are designed for use in Hydronic radiant panel heating and cooling applications. They are available in various sizes, configurations, and options
More informationCatalogue Easy inside
Catal ogue 2.2010 The complete product range Mini Middle Page 4: Unifix Mini: The small, light and quick repair solution for sealing holes, fractures and porous areas in water-bearing pipes. Suitable for
More informationCHEVORLET IMPALA
1962-64 CHEVORLET IMPALA Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 1 deck lid harness 4 grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN
More informationAquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationSPEEDKEY KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 9. GEM e2, e4, e6, el XD
SPEEDKEY KIT P/N 2883054 APPLICATION GEM e2, e4, e6, el XD BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions
More informationPONTIAC FIREBIRD. Four Panel Sequential LED Tail Light Kit Installation Guide
1967-68 PONTIAC FIREBIRD Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN 1100567 Please
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationConsists of. Date:17/02/2011 Page 1/8
Consists of 470518 Qty. Product 4 1 DEFA Termina - interior heater with holder 1 1 DEFA Futura - time program controller/timer 3 1 DEFA MultiCharger 1203 - battery charger/relay 6 1 DEFA Extension cable
More informationE E VDC COOLEDGE TILE INTERIOR INSTALLATION INSTRUCTIONS. Caution: Observe precautions for handling electrostatic sensitive devices.
5 YEAR WARRANTY 5 YEAR WARRANTY COOLEDGE TILE INTERIOR INSTALLATION INSTRUCTIONS E354088 LISTED AC E354088 58VDC E354088 E354088 5 5 YEAR WARRANTY 5 YEAR WARRANTY E354088 Caution: Observe precautions for
More informationPart Name/Description Part Number Quantity Instruction Kit Metalfor Flow Sensor
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Flow Sensor 4001356 1 Deflector plate 2000612-1 1
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only CAUTION: Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect
More informationMAKING MODERN LIVING POSSIBLE. Quick Setup VLT FCM 300 Series. Phone: Fax: Web: -
MAKING MODERN LIVING POSSIBLE Quick Setup VLT FCM 300 Series Factory setting Motors type B14 & B34 mounting Reset (pushbutton) Start Jog Speed reference Fig. 1 - Reset to be closed short time for resetting
More informationPRODUCT SAFETY NOTICE DEALER/INSTALLER NOTICE
PRODUCT SAFETY NOTICE Congratulations. This vehicle has been equipped with a Firestone air suspension system. This suspension will enhance the vehicle s handling when loaded, however, the vehicle s performance
More informationInstructions for 2-row monitoring only
Installation Instructions for CaseIH cotton picker models: Instructions for 2-row monitoring only Ensure the model numbers shown above correspond to the machine model. If you receive the incorrect installation
More informationPowrTwin 8900XLT. Owner s Manual. Do not use this equipment before reading this manual!
Owner s Manual For professional use only Do not use this equipment before reading this manual! PowrTwin 00XLT Model Number: Gas Bare -0 DC Electric Bare -0 Gas Complete - Gas/Electric Complete -0 NOTE:
More informationNote: If anything is damaged or missing, contact your customer representative immediately.
Package Contents The package includes: 1 Chassis 1-18 leafs according to the amount ordered 18 - X leaf blanks X = the amount ordered 1 leaf fan module 1 spine fan module 9 spines 1-2 management modules
More informationInformation Sheet Polyethylene Tank Assemblies
Information Sheet Polyethylene Tank Assemblies No. 27421 10 Gallon Tank Assembly Ultraviolet resistant, yellow polyethylene tank. Molded recesses for mounting of any LMI Series A, J, or P pump. Convenient
More informationAF0465-XX SERVICE KITS GENERAL DESCRIPTION MODEL DESCRIPTION CHART OPERATING AND SAFETY PRECAUTIONS THIS MANUAL COVERS THE FOLLOWING MODELS
OPERATOR S MANUAL INCLUDING: SERVICE KITS, TROUBLESHOOTING, PARTS LIST, DISASSEMBLY & REASSEMBLY. 4-1/4 AIR MOTORS AF044X-XX (4 STROKE) and AF046X-XX (6 STROKE) Also covers 637489 service kits AF044X-XX
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More information354 CHAPTER EIGHT WATER PUMP
354 CHAPTER EIGHT 33 Shift handle F : Forward N : Neutral R : Reverse proper alignment of the water tube to the water pump opening during each installation attempt. Make sure the locating pins enter the
More informationInstallation Instructions
Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab
More informationGenerator Fire Safety: Generator assemblies should be located outside the building.
SECTION 33 70 00 - ELECTRICAL DISTRIBUTION PACKAGED GENERATOR ASSEMBLIES Generator Fire Safety: Generator assemblies should be located outside the building. All fuel piping from the outside of the building
More informationOperations Manual Eagle 1000 Series Stretch Wrapper
Operations Manual Eagle 1000 Series Stretch Wrapper Models A & B - 1 - READ ALL INSTRUCTIONS CONTAINED IN THIS MANUAL PRIOR TO MACHINE INSTALLATION! - 2 - Contents page 1. Machine Safety Information 1.1
More informationHydroCycle 6" Pro NFT Lettuce Systems
HydroCycle 6" Pro NFT Lettuce Systems Designed to grow healthy plants without soil using mineral-nutrient solutions. 2016 Growers Supply All Rights Reserved. Reproduction is prohibited without permission.
More informationINSTALLATION INSTRUCTIONS Part# , , ,
INSTALLATION INSTRUCTIONS Part# 20-0218, 22-0318, 20-0118, 22-0219 20-0218 - 4 Tire On Board Air Delivery System and Dual Compressed Air System Includes ARB CKMTA12 Compressor 20-0118 - 2017 FORD RAPTOR
More information4.2 WATER PUMP (GEAR CASE MOUNTED AND LATER) (GCM)
SERIES 60 SERVICE MANUAL 4.2 WATER PUMP (GEAR CASE MOUNTED - 1991 AND LATER) (GCM) The centrifugal-type water pump circulates the engine coolant through the cooling system. The pump is mounted on the rear
More informationHydroCycle 4" Pro NFT Lettuce Systems
HydroCycle 4" Pro NFT Lettuce Systems 112251 Hydroponic Lettuce Table* Designed to grow healthy plants without soil using mineral-nutrient solutions. *Actual system may differ from what is shown. 2016
More informationD24-53 Series Electric Non-Spring Return Actuators 53 lb in Models (6 N m)
Installation Instructions D24-53 Issue Date November 4, 23 D24-53 Series Electric Non-Spring Return Actuators 53 lb in Models (6 N m) Installation IMPORTANT: The D24-53 Series actuator is intended to control
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationOne- Touch Installation Instructions
One- Touch Installation Instructions 1 1 Height Adjustable Pivot w/ screws 9 Upper Work Surface 2 Rail Mount Knobs 10 Back Cover 3 Transformer 11 Center Pivot w/ screws 4 Support Legs 12 Left Monitor Arm
More informationFour Panel Amber LED Front Light Kit Installation Guide
Four Panel Amber LED Front Light Kit Installation Guide Kit Contents: 2 LED panels 4 socket plugs 1 cut out template PN 2100886 Please refer to webiste for full warranty information. DIGI-TAILS is not
More informationAsymmetrical Installation Instructions. Components: i2cove Asymmetrical LED Light Fixtures. 12 [305mm] [918mm] 48.
support@i2systems.com www.i2systems.com Electrical Specifications PARAMETER Input Power VALUE 8 Watts* / Ft Input Voltage 120-277V AC, 50/60 Hz Max. Fixture Run Length LED Color (CCT) 8 Watts: 120VAC:
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.
Installation Instructions RT8RT/RT5RT Relight Assembly READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION. IMPORTANT SAFETY INSTRUCTIONS WARNING: FAILURE
More informationMirror Solutions Bevel & Pivot Models Installation Instructions INSTALLATION INSTRUCTIONS. Figure 1
Installation Instructions Mirror Solutions Bevel & Pivot Models 620095-620098 Mirror Solutions Bevel - Models # 620095 & 620096 Mirror Solutions Pivot - Models # 620097 & 620098 Figure 1 INSTALLATION INSTRUCTIONS
More informationEmpty enclosures IEC 62208
374 www.hensel-electric.de/en in accordance with for customized solutions and individual applications for example for low-voltage switchgear and controlgear assemblies i n accordance with the IEC 61439-series
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger (2009-) Straight UTV Steel Plow with Vehicle Mount Kit 6 Wide Snow Plow (p/n: 1POLSP) (fits the 500 H.O., 700 & 800 HD & XP) The contents
More informationInstallation Instructions
Contents Page General Information and Installer Tips.......... 2 Panels & Posts............................. 3 Enclosure Description..................... 4 Hinge Door Hardware................... 4-5 Step-by-Step
More informationMPPT Solar Integrated Inverters (500VA~2500VA) User Manual THE SOLAR TECH CO.,LTD. Solar Integrated Inverter Series 500VA~2500VA 13.
MPPT Solar Integrated Inverters (500VA~2500VA) User Manual THE SOLAR TECH CO.,LTD. - 1 - Table of Contents 1. SALIENT FEATURES...3 2.. PRODUCT INSTALLATION & PRECAUTIONS...3 2.1. PRODUCT INSTALLATION &
More informationLoose Parts Note: Determine the left and right sides of the machine from the normal operating position.
Brake Kit Dingo TX 0 & Compact Utility Loader Part No. 0 0 & 0 Loose Parts Note: Determine the left and right sides of the machine from the normal operating position. Description Qty. Use Drive wheel Brake
More informationPN EL CAMINO w/reverse Two panel Sequential LED Taillight kit installation guide. Kit Contents:
1978-81 EL CAMINO w/reverse Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness, 48 2
More informationVERTICAL TYPE LIMIT SWITCHES (INCLUDES LAMP TYPE)
VERTICAL TYPE LIMIT SWITCHES (INCLUDES LAMP TYPE) Limit Switches General use vertical limit switch. Type with a lamp which makes maintenance convenient; either a neon AC powered lamp or an LED DC powered
More informationSTAY ON TRACK WITH THIS LINE FOLLOW BUGGY WITH :MOVE LINE FOLLOW BOARD FOR BBC MICRO:BIT
STAY ON TRACK WITH THIS LINE FOLLOW BUGGY WITH :MOVE LINE FOLLOW BOARD FOR BBC MICRO:BIT BUILD INSTRUCTIONS LIST OF FIXINGS M3 BOLTS M3 NUTS STANDOFFS 6mm x12 x4 x4 10mm x4 x12 12mm x2 30mm x2 20mm M-F
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W
B&W Trailer Hitches 6 Hawaii Rd / PO Box 86 Humboldt, KS 66748 P:60.473664 F:60.869.903 Turnoverball Gooseneck Hitch Installation Instructions MODEL 08
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700) (4510/4610/4710) (4120/4320/4520/4720) HARD SIDED CAB ENCLOSURE (p/n 1JD4120AS) SOFT SIDED CAB ENCLOSURE
More informationPage 1. File: Motolight caliper one-piece Date: 8/14/2006
Page 1 Caliper Mount Installation One-piece mounting brackets You should allow about two to three hours for installation. We suggest you use a well-lighted space for installation. PLEASE READ ALL THE INSTRUCTIONS.
More informationFlow Sensor
NOTE: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Instruction Kit Metalfor 4101091 1 Quick reference sheet 2002831-36 1 Installation instructions
More informationFour Panel Sequential LED Tail Light Kit Installation Guide
1969 CHEVY CAMARO Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED harnesses,
More informationFOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT, PLEASE READ THE FOLLOWING INSTRUCTIONS.
Installation Instructions for Mercmaster LED Low Profile Luminaire Fittings 650499-000 INSTRUCTION SHEET FOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT, PLEASE READ THE FOLLOWING INSTRUCTIONS. Product
More informationOperating Instructions Bedienungsanleitung Mode d emploi EWB EWB
Operating Instructions Bedienungsanleitung Mode d emploi DW 400 EWB 400 575 EWB 400 575 800 www.bron-kobold.com Operating instructions EWB 400.575 EWB 400.575.800 Before use Please read all the information
More informationThermal hysteresis 0.5% max. of full scale (within compensated temperature range) 1% max. for ranges mbar mbar mbar
Pressure Transmitter Type FM40466 General application Pressure transmitters are used to measure the relative (gauge) and absolute pressures in liquids or gases. The measuring device for the transmitter
More informationRostselmash Torum 740
Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part Number 740 Combine Kit Torum 740 4100762 1 Threaded Arm Assembly 2000311-2 1 Header
More informationINSTALLATION INSTRUCTIONS AND OWNER S MANUAL
INSTALLATION INSTRUCTIONS AND OWNER S MANUAL Thank you for purchasing the AlloyCover from WeatherTech. Manufactured with pride using superior quality materials and workmanship. With proper care, your cover
More informationStay-IN-Play with Panic Stop Braking
INSTALLATION INSTRUCTIONS TOWED VEHICLE BRAKING SYSTEM Stay-IN-Play with Panic Stop Braking SMI Manufacturing, Inc. P.O. Box 14040 Evansville, IN 47728 1-800-893-3763 www.smibrake.com SIP0906 Model SIP0603
More informationL Intake Manifold Part #
86-93 5.0L Intake Manifold Part #5001-5002 I N S T A L L A T I O N I N S T R U C T I O N S Supplied Materials Bottom cover, Upper manifold, Lower manifold, Plenum cover plate, 1501 Throttle body (comes
More informationInstallation Manual for VHM-25 Series Arms Channel Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for VHM25 Series Arms Channel Mount Install Time: 1015 minutes The purpose of this manual
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. of 0 INSTALLATION & OWNER S MANUAL MASSEY FERGUSON GC2400 cab kit p/n MFGC2400 Installation Instructions The contents of this envelope are the property of the owner. Be sure to leave with the
More information