SELECT HIGH-LOW SYSTEM
|
|
|
- Ernest Henry
- 5 years ago
- Views:
Transcription
1 Page 1 of 15 Your satisfaction is my GREATEST CONCERN, and I'm happy to answer any follow-up questions you may have. You can contact me anytime@ SELECT HIGH-LOW SYSTEM LOCATION Fig. 107: Locating Select High-Low System Lights & Components INSPECTION
2 Page 2 of 15 NOTE: Switch the four wheel drive control switch under the condition that A/T shift lever is in "N" position and the vehicle speed is 5 km/h or less. Do not operate the four wheel drive control switch and the differential lock switch at the same time. 1. INSPECT H4 (Differential lock "FREE") To H4 (Differential lock "LOCK") SHIFT a. Start the engine, and the differential lock switch is in "OFF" position. b. Turn the four wheel drive control switch to "H4" position while pressing it. c. Check that the center diff. lock indicator light comes on after pressing the differential lock switch for 2 seconds. Check that the center diff. lock indicator light goes off after pressing the differential lock switch for 2 seconds.
3 Page 3 of 15 Fig. 108: Checking Center Diff. Lock Indicator Light Operation (H4 Position) 2. INSPECT L4 (Differential lock "FREE") To L4 (Differential lock "LOCK") SHIFT a. Start the engine, and differential lock switch is in "OFF" position. b. Turn the four wheel drive control switch to "L4" position while pressing it. c. Check that the 4LO indicator light comes on after it is blinking. d. Check that the center diff. lock indicator light comes on after pressing the differential lock switch for 2 seconds. Check that the center diff. lock indicator light goes off after pressing the differential lock switch for 2 seconds.
4 Page 4 of 15 Fig. 109: Checking Center Diff. Lock Indicator Light Operation (4LO Position) 3. INSPECT H4 (Differential lock "FREE") To L4 (Differential lock "FREE") SHIFT
5 Page 5 of 15 a. Start the engine, and differential lock switch is in "OFF" position. b. Turn the four wheel drive control switch from the "H4" position to the "L4" position while pressing it. c. Check that the 4LO indicator light comes on after it is blinking. d. Turn the four wheel drive control switch from the "L4" position to the "H4" position while pressing it. e. Check that the 4LO indicator light goes off after it is blinking. Fig. 110: Checking 4LO Indicator Light Operation (1 Of 2) 4. INSPECT H4 (Differential lock "LOCK") To L4 (Differential lock "LOCK") SHIFT a. Start the engine, and differential lock switch is in "OFF" position. b. Check that the center diff. lock indicator light comes on after pressing the differential lock switch for 2 seconds. c. Turn the four wheel drive control switch from the "H4" position to the "L4" position while pressing it. d. Check that the 4LO indicator light comes on after it is blinking.
6 Page 6 of 15 e. f. Turn the four wheel drive control switch from the "L4" position to the "H4" position while pressing it. Check that the 4LO indicator light goes off after it is blinking.
7 Page 7 of 15 Fig. 111: Checking 4LO Indicator Light Operation (2 Of 2)
8 Page 8 of INSPECT DIFFERENTIAL LOCK SWITCH CONTINUITY a. Remove the instrument panel finish lower panel sub-assy. b. Remove the differential lock switch from the instrument panel finish lower sub-assy. c. Inspect the continuity between the each terminal. DIFFERENTIAL LOCK SWITCH CONTINUITY Switch Position Tester Connection (Terminal Specified Condition No.) OFF +B (3) & GND (4) No Hold ON +B (3) & GND (4) Illumination ILL+(1) & ILL- (2) If continuity is not as specified, replace the differential lock switch or bulb.
9 Page 9 of 15
10 Page 10 of 15
11 Page 11 of 15 Fig. 112: Identifying Differential Lock Switch & Terminals 6. INSPECT FOUR WHEEL DRIVE CONTROL SWITCH a. Remove the center instrument cluster finish panel sub-assy. b. Remove the four wheel drive control switch from the center instrument cluster finish panel sub-assy. c. Inspect the continuity between the each terminals. FOUR WHEEL DRIVE CONTROL SWITCH CONTINUITY Switch Position Tester Connection (Terminal Specified Condition No.) H4 LO (2) & GND (4) No L4 LO (2) & GND (4) Illumination ILL+ (1) & ILL- (3) If continuity is not as specified, replace the four wheel drive control switch or bulb.
12 Page 12 of 15 Fig. 113: Identifying Four Wheel Drive Control Switch Connector Terminals 7. INSPECT ACTUATOR NOTE: Inspection for the actuator must be done with the actuator installed on the transfer assembly. a. Turn the ignition switch to ON. b. Check the operating sound produced by four wheel drive control switch operation and the differential lock switch operation. If the operating sound cannot be heard, check the four wheel drive control ECU and the wire harness in the next step. When the wire harness and four wheel drive control ECU is normal, replace the actuator.
13 Page 13 of 15
14 Page 14 of 15 Fig. 114: View Of Four Wheel Drive Control ECU & Shift Actuator Connectors 8. INSPECT WIRE HARNESS a. Disconnect the actuator connector and four wheel drive control ECU connector. b. Check continuity on the wire harness between four wheel drive control ECU and the actuator. WIRE HARNESS CONTINUITY Tester Connection (Connector & Terminal No.) TM1 (F10-2) - TM1 (T3-2) TM2 (F10-5) - TM2 (T3-1) TL2 (F10-24) - TL2 (T3-4) TL3 (F10-23) - TL3 (T3-5) HM2 (F10-4) - HM2 (T3-7) HM1 (F10-1) - HM1 (T3-8) P1 (F10-22) - CDL (T3-9) HL2 (F10-26) - HL2 (T3-11) HL1 (F10-17) - HL1 (T3-12) Specified Condition If continuity is not as specified, repair or replace the wire harness. 9. INSPECT FOUR WHEEL DRIVE CONTROL ECU a. Connect the wire harness side connector to the four wheel drive control ECU and inspect wire harness side connector from the back side, as shown in Fig Fig. 115: Standard Value Of ECU Terminal
15 Page 15 of 15 Fig. 116: Standard Value Of ECU Terminal Chart Your satisfaction is my GREATEST CONCERN, and I'm happy to answer any follow-up questions you may have. You can contact me
HOW TO PROCEED WITH TROUBLESHOOTING
2005 BRAKES Anti-Lock Brake System With Electronic Brake Force Distribution (EBD) - Diagnostics - RAV4 HOW TO PROCEED WITH TROUBLESHOOTING Troubleshoot in accordance with the following procedures. Fig.
J4WD SYSTEM 1. General
CHASSIS TRANSFER CH-93 J SYSTEM 1. General D The system used on the new Land Cruiser (Station Wagon) allows the driver to select the appropriate mode from among the four drive modes by utilizing the transfer
1995 Honda Accord LX. ANTI-LOCK BRAKE SYSTEM' ' BRAKES Honda - Anti-Lock
TROUBLE SHOOTING ANTI-LOCK (ABS) WARNING LIGHT NOTE: ABS system is okay if ABS warning light goes out after engine is started. Diagnostic Trouble Code (DTC) Recognition 1. ABS control unit recognizes system
VSC OFF Indicator Light Remains ON
6 RAKE CONTROL VEHICLE STAILITY CONTROL SYSTEM VSC OFF Indicator Light Remains ON DESCRIPTION When the rear differential is locked or during the WD mode, VSC control turns off and the VSC OFF indicator
1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED AREA OR NEAR AN OPEN FLAME
2006 Toyota 4Runner 4.0L Eng Limited 1Search AIR CONDITIONER REQUESTED INFORMATION PRECAUTION 1. DO NOT HANDLE REFRIGERANT IN AN ENCLOSED AREA OR NEAR AN OPEN FLAME 2. ALWAYS WEAR EYE PROTECTION Fig 1:
CRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM CONTROL SYSTEM PARTS LOCATION CRUISE CONTROL CRUISE CONTROL SYSTEM 1 ENGINE ROOM R/B AND J/B MAIN BODY ECU (INSTRUMENT PANEL J/B) B142328E05 2 CRUISE CONTROL CRUISE CONTROL SYSTEM
1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITS
841006 013 Fuse and relay 841006 1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITS Remove the negative battery cable from the battery in advance when working on electrical units. Make sure to turn "OFF" the
DTC C1735/35 Exhaust Solenoid Valve Circuit
8 DTC C7/ DTC C74/4 Rear Height Control Gate Solenoid Valve Circuit Malfunction Rear Height Control Leveling Solenoid Valve Circuit Malfunction DTC C75/5 Exhaust Solenoid Valve Circuit DTC C744/44 Tank
CRUISE CONTROL SYSTEM
Negative (-) Battery Terminal CRUISE CONTROL CRUISE CONTROL SYSTEM Cable System name METER / GAUGE SYSTEM D033496E01 CRUISE CONTROL SYSTEM PRECAUTION 1 1. DISCONNECT AND RECONNECT CABLE OF NEGATIVE BATTERY
PRE CHECK 1. DIAGNOSIS SYSTEM
DI208 F05261 PRECHECK DI3GC05 1. DIAGNOSIS SYSTEM (a) Check the indicator light. (1) Turn the ignition switch. (2) Check t hat t he height cont r ol indicat or light and height control indicator light
11. CLUSTER Electrical Wiring Diagrams 1) GAUGE (SPEED, RPM, FUEL, TEMP), WARNING LAMP (FUEL, FUEL FILTER, ABS/ESP, BRAKE, HDC, 4WD)
548 s 11. CLUSTER 1) GAUGE (SPEED, RPM, FUEL, TEMP), WARNING LAMP (FUEL, FUEL FILTER, ABS/ESP, BRAKE, HDC, 4WD) s 549 A. CONNECTOR INFORMATION Connector Number (Pin Number, Color) Connecting Wiring Harness
ON-VEHICLE INSPECTION
32 SUSPENSION CONTROL AIR SUSPENSION SYSTEM ON-VEHICLE INSPECTION 1. CHECK FLUID LEAKAGE Check the connections of tube and parts for fluid leakage. : Supply parts only C099149E01 SUSPENSION CONTROL AIR
DTC C0273/13 OPEN CIRCUIT IN ABS MOTOR RELAY CIRCUIT DTC C0274/14 SHORT CIRCUIT IN ABS MOTOR RELAY CIRCUIT
0804 DTC C0273/13 OPEN CIRCUIT IN ABS MOTOR RELAY CIRCUIT 0F1Q09 DTC C0274/14 SHORT CIRCUIT IN ABS MOTOR RELAY CIRCUIT DTC C1361/91 SHORT CIRCUIT IN ABS MOTOR FAIL SAFE RELAY CIRCUIT CIRCUIT DESCRIPTION
Zoom and Print Options
Vehicle» A L L Diagnostic Trouble Codes ( DTC )» Testing and Inspection» P Code Charts» P0707» CVT Automatic Transaxle P0707-TRANSMISSION RANGE SENSOR CIRCUIT LOW http://repair.alldata.com/alldata/article/display.action?componentid=3926&itypeid=423&nonstandardid=1733324&vehicleid=42661&windowname=m
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. MII 12455 DIGITAL METER KIT MUV700 P/N 08E80-HL1-100 Issue Date July 2008 Honda Dealer: Please give a copy of these instructions to your
CRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Cruise Control Systems Celica DESCRIPTION Cruise control system consists of Cruise Control Electronic
ES300, GS300, LS400, SC300 & SC400 Camry, Celica, Corolla, Land Cruiser, MR2, Paseo, Pickup, Supra, Tercel & 4Runner
Page 1 of 49 ARTICLE BEGINNING APPLICATION APPLICATION Application Lexus Toyota Model ES300, GS300, LS400, SC300 & SC400 Camry, Celica, Corolla, Land Cruiser, MR2, Paseo, Pickup, Supra, Tercel & 4Runner
CRUISE CONTROL SYSTEM
CRUISE CONTROL CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM PRECAUTION 1 1. NOTICE FOR INITIALIZATION NOTICE: When the cable of the negative () battery terminal is disconnected, initialize the following
CRUISE CONTROL SYSTEM
CRUISE CONTROL CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM PRECAUTION 1 1. HANDLING PRECAUTION FOR CRUISE CONTROL SYSTEM (a) Turn the cruise control main switch OFF when not using the cruise control system.
DTC C2121/21 No Signal from Transmitter ID1. DTC C2122/22 No Signal from Transmitter ID2. DTC C2123/23 No Signal from Transmitter ID3
TIRE ND WHEEL TIRE PRESSURE WRNI SYSTEM 33 DTC C2121/21 No Signal from Transmitter ID1 DTC C2122/22 No Signal from Transmitter ID2 DTC C2123/23 No Signal from Transmitter ID3 DTC C2124/24 No Signal from
BE 46 BODY ELECTRICAL SYSTEM COMBINATION METER COMBINATION METER PARTS LOCATION
BE46 PARTS LOCATION BE47 METER CIRCUIT (4AFE, 5SFE Engine) No. 1 2 3 4 5 6 8 9 10 Wiring connector side Brake Fluid Level Warning Switchterminal 1, and Parking Brake Switch Igniter DOME Fuse Door Courtesy
PRE-CHECK USA: DI-224 DLC1 E 1 ABS WITH EBD & BA & TRAC & VSC SYSTEM 2WD: CANADA: 4WD:
DI224 2WD: 4WD: USA: CANADA: F14323 PRECHECK DI8XO02 1. DIAGNOSIS SYSTEM (a) Inspect the battery positive voltage. Battery positive voltage: 10 14 V (b) Check the warning lights and buzzer. (1) Release
AUTOMATIC SHOULDER BELT SYSTEM
AUTOMATIC SHOULDER BELT SYSTEM 1992 Subaru SVX 1992-96 ACCESSORIES/SAFETY EQUIPMENT Subaru Automatic Shoulder Belt System Subaru; SVX OPERATION RAIL & MOTOR NOTE: After replacing any parts/components,
BE 30 BODY ELECTRICAL SYSTEM. Combination Meter COMBINATION METER. Parts Location
BE30 BODY ELECTRICAL SYSTEM COMBINATION METER Parts Location BODY ELECTRICAL SYSTEM BE31 Meter Circuit (w/o Tachometer) No. 2 7 9 12 1 2 3 5 7 9 3 Wiring connector side ETC Pattern select switch A/T Oil
ONLY WIRELESS CONTROL FUNCTION DOES NOT OPERATE (PREPARE NEW OR NORMAL TRANSMITTER OF THE SAME TYPE VEHICLE)
DIAGNOSTICS ONLY WIRELESS CONTROL FUNCTION DOES NOT OPERATE (PREPARE NEW OR NORMAL TRANSMITTER OF THE SAME TYPE VEHICLE) 05679 05DLG01 CIRCUIT DESCRIPTION The door control receiver receives a signal from
ARTICLE BEGINNING DESCRIPTION & OPERATION TIRE PRESSURE MONITOR (TPM) SYSTEM
Page 1 of 5 ARTICLE BEGINNING DESCRIPTION & OPERATION TIRE PRESSURE MONITOR (TPM) SYSTEM The tire pressure warning system informs the driver if it detects a low tire pressure. When the tire pressure warning
G - TESTS W/CODES Nissan 240SX * PLEASE READ THIS FIRST * INTRODUCTION SELF-DIAGNOSTIC SYSTEM DESCRIPTION HARD FAILURES INTERMITTENT FAILURES
G - TESTS W/CODES 1990 Nissan 240SX 1990 ENGINE PERFORMANCE Self-Diagnostics Nissan 240SX and Axxess * PLEASE READ THIS FIRST * NOTE: This article has been revised according to Technical Service Bulletin
TO INDEX LIGHTING SIDE TURN SIGNAL LIGHT ASSEMBLY LH TAILLIGHT (REAR COMBINATION LIGHT) ASSEMBLY LH LICENSE PLATE LIGHT ASSEMBLY
TO INDEX BODY AND ELECTRICAL GHTING GHTING SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... BASIC INSPECTION..........................................
ENGINE IMMOBILISER ENGINE IMMOBILISER SYSTEM REGISTRATION
6 REGISTRATI 1. DESCRIPTI OF CODE REGISTRATI (a) When adding master keys and sub-keys (additional registration). (1) Register the key code (immobiliser code) in the transponder key ECU assembly. (b) "A"
Volkswagen B3 Passat Diagnosis, Fault Memory - Passat Diagnosis, Fault Memory (Page GR-D4)
Diagnosis, Fault Memory (Page GR-D4) Anti-lock brake system (ABS) electrical testing self-diagnosis troubleshooting using electrical steps VAG 1551 Diagnostic Tester connecting erasing Fault memory reading
10.1 Electronic Stability Program (ESP) and Speed-sensitive Power Steering (SPS) Contents
10.1 lectronic Stability Program (SP) and Speed-sensitive Power Steering (SPS) Contents 10.1 Models 129 (with engine 104, 119) up to M.Y. 1999, Model 129 (with engine 120), 140, 210 as of M.Y. 1996 Page
ELECTRONICALLY CONTROLLED 4WD
27C-1 GROUP 27C ELECTRONICALLY CONTROLLED 4WD CONTENTS SERVICE PRES......... 27C-3 SERVICE SPECIFICATIONS....... 27C-3 SEALANT...................... 27C-3 SPECIAL TOOLS................ 27C-4............
ANTI-LOCK BRAKE SYSTEM - REAR WHEEL
ANTI-LOCK BRAKE SYSTEM - REAR WHEEL 1994 Nissan Pickup 1994 BRAKES Nissan - Rear Anti-Lock Pathfinder, Pickup DESCRIPTION In 2WD mode, Rear Anti-Lock Brake System (RABS) helps the driver to maintain steering
TURN SIGNAL AND HAZARD WARNING SYSTEM
BE68 BODY ELECTRICAL SYSTEM TURN SIGNAL AND HAZARD WARNING SYSTEM DESCRIPTION The component parts of this system and their function are as shown in the following table. Parts Name Function Turn Signal
DIAGNOSIS. https://mitsubishitechinfo.com/data/st41/2003/m /html/m of 6 1/17/2016 5:45 PM
1 of 6 1/17/2016 5:45 PM DIAGNOSIS Required Special Tools: MB991223: Harness Set MB991502: Scan Tool (MUT-II) MB991862: SWS monitor kit STEP 1. Use scan tool MB991502 to select "ECU COMM CHK" on the SWS
ANTI-LOCK BRAKE SYSTEM
ANTI-LOCK BRAKE SYSTEM 1992 Infiniti G20 1990-92 BRAKES Infiniti Anti-Lock Brake System Infiniti; G20, M30, Q45 DESCRIPTION & OPERATION The Anti-Lock Brake System (ABS) prevents wheel lock-up during abrupt
1 The speedometer displays the speed of machine in mph and km/h Emergency warning lamp Right turning pilot lamp Hyd oil temp gauge Fuel gauge
. CLUSTER ) STRUCTURE The cluster consists of gauges, lamps and LCD as shown below, to warn the operator in case of abnormal machine operation or conditions for the appropriate operation and inspection.
Only Wireless Control Function is Inoperative
49 Only Wireless Control Function is Inoperative DESCRIPTI The door control receiver receives signals from the transmitter and sends these signals to the multiplex network body ECU. The multiplex network
BE 29. COMBINATION METER Parts Location
BODY ELECTRICAL SYSTEM BE29 COMBINATION METER Parts Location BE30 BODY ELECTRICAL SYSTEM Meter Circuit (w/o Tachometer) Wiring connector side Speed Sensor SIGVAL ETC Pattern select switch A/T Oil Temperature
TRACTION CONTROL SYSTEM 1996 Toyota Supra 1995-96 BRAKES Traction Control Supra DESCRIPTION Toyota Traction Control (TRAC) system controls engine torque and braking of the driving wheels. TRAC system is
1. SERIAL NUMBER LOCATION 1 2. CHANGED ITEMS COMPARED WITH S-FIVE 2 3. SPECIFICATIONS 6 4. CABLE & HARNESS ROUTING 7 5. INSPECTION / MAINTENANCE 10
This E-FIVE service manual contains only items, which is changed due to the design change from S-FIVE. For items not explained in this manual, refer to S-FIVE service manual. CONTENTS 1. SERIAL NUMBER
CRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1993 Mitsubishi Montero 1993 ACCESSORIES & EQUIPMENT Mitsubishi Cruise Control Systems Montero DESCRIPTION & OPERATION The cruise control system is electronically and vacuum controlled.
Power Supply Circuit For Transfer Control Unit
Page 1 of 7 2005 Nissan Xterra 4.0L Eng S Power Supply Circuit For Transfer Control Unit CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE Data are reference value. DATA MONITOR MODE REFERENCE Monitored
Taillight Relay Circuit
GHTI GHTI SYSTEM 63 Taillight Relay Circuit DESCRIPTION The headlight dimmer switch sends a signal to the main body ECU. WIRI DIAGRAM Main Body ECU TAIL To Battery TAIL TRLY Outer Rear View Mirror Illumination
STEERING COLUMN VARIABLE GEAR RATIO STEERING SYSTEM CALIBRATION. (a) Check for DTC. Result. DTC C1515/15 is not output DTC C1515/15 is output
56 STEERING COLUMN VRILE GER RTIO STEERING SYSTEM CLIRTION 1. VGRS SYSTEM CLIRTION PROCEDURE (USING SST CHECK WIRE) Use this procedure to center the steering wheel position if: VGRS actuator has been replaced
DTC C1238/38 FOREIGN MATTER IS ATTACHED ON TIP OF RIGHT REAR SENSOR DTC C1239/39 FOREIGN MATTER IS ATTACHED ON TIP OF LEFT REAR SENSOR
DIAGNOSTICS DTC C00/33 RIGHT REAR SPEED SENSOR 05795 05H3B03 DTC C05/34 LEFT REAR SPEED SENSOR DTC C38/38 FOREIGN MATTER IS ATTACHED ON TIP OF RIGHT REAR SENSOR DTC C39/39 FOREIGN MATTER IS ATTACHED ON
ABS WITH EBD SYSTEM (April, 2003)
05 294 ABS ITH EBD SYSTEM (April, 2003) HO TO PROCEED ITH TROUBLESHOOTI Vehicle Brought to orkshop 057U7 04 2 Customer Problem Analysis (See page 05 296) 3 Check and Clear DTCs and Freeze Frame Data (See
CRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM 1992 Infiniti G20 1991-92 SAFETY EQUIPMENT Infiniti Cruise Control Systems G20, M30, Q45 DESCRIPTION & OPERATION NOTE: For system component locations, see SYSTEM COMPONENT LOCATIONS.
Intake manifold change-over
Page 1 of 10 24-67 Intake manifold change-over This test should only be performed if there is a performance deficiency. The intake manifold switches from the long intake path to the short one at approx.
The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
Page 1 of 19 DTC B1800/51 SHORT IN DRIVER SIDE SQUIB CIRCUIT; DTC B1801/51 OPEN IN DRIVER SIDE SQUIB CIRCUIT; DTC B1802/51 SHORT TO GND IN DRIVER SIDE SQUIB CIRCUIT; DTC B1803/51 SHORT TO B+ IN DRIVER
PRE-CHECK ABS Warning Light BRAKE Warning Light USA: USA: Canada: Canada: VSC Warning Light SLIP Indicator Light. TRAC OFF Indicator Light
ABS Warning Light BRAKE Warning Light USA: Canada: USA: Canada: VSC Warning Light SLIP Indicator Light TRAC Indicator Light F45096 PRECHECK 05765 05H3Y02 1. DIAGNOSIS SYSTEM (a) Check the warning lights.
Electronic Control System
AT440 AUTOMATIC TRANSMISSION A340F 4WD Electronic Control System PRECAUTION Do not open the cover or the case of the ECU and various computer unless absolutely necessary. (If the IC terminals are touched,
Transfer Control Device
Page 1 of 9 2005 Nissan Xterra 4.0L Eng S Transfer Control Device CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE Data are reference value. DATA MONITOR MODE REFERENCE Monitored item [Unit] Content Condition
The following rear differential is provided for the off-road package models. BD20B (with Differential Lock Actuator)
6 4RUNNER NEW FEATURES NEW FEATURES DIFFERENTIAL (OFF-ROAD PACKAGE MODELS) 1. General The following rear differential is provided for the off-road package models. Rear Differential Lock Actuator 233CH46
Headlight TOYOTA TACOMA (EWD614U) W W. From Power Source System (See Page 72) R- B R- B 10A IG1 NO. 2 20A DR LCK. 7. 5A ECU- B DIM Relay 1 2C
Headlight From ower Source System (See age 7) 0A IG NO. 0A D LCK 7. 5A ECU- B DIM elay 3 5 HEAD elay 3 5 C 9 IA A HLY 6 C 5 6 IG ALTB ECUB 30 Y- B Y- B IA 5 A DIM B 5(A) Body ECU B HEAD HF HU GND KB L
1994 Mazda MX-5 Miata. ANTI-LOCK BRAKE SYSTEM 1994 BRAKES Mazda - Anti-Lock
ANTI-LOCK BRAKE SYSTEM 1994 BRAKES Mazda - Anti-Lock DESCRIPTION The Anti-Lock Brake System (ABS) control unit senses reductions in front and rear wheel speed and modulates hydraulic pressure to the brakes
ANTI-LOCK BRAKE SYSTEM
ANTI-LOCK BRAKE SYSTEM 1993 Mitsubishi Diamante 1993 BRAKES Mitsubishi - Anti-Lock Brake System Diamante DESCRIPTION The Anti-Lock BRAKE SYSTEM (ABS) is designed to prevent wheel lock-up during heavy braking.
7. Diagnostics Chart for Warning Light
7. Diagnostics Chart for Warning Light Circuit Failure A: TROUBLE CODE DOES NOT APPEAR. TCS WARNING LIGHT COMES ON WHEN STARTING THE ENGINE. 1. Check TCS warning light. Repair harness. 2. Check diagnosis
LIGHTING SYSTEM PRECAUTION LI 1
System Name Power Window Control System GHTING GHTING SYSTEM GHTING SYSTEM PRECAUTION 1 1. PRECAUTION FOR DISCONNECTING BATTERY CABLE NOTICE: FOR INITIAZATION: When disconnecting the cable from the negative
G - TESTS W/CODES - 2.2L
G - TESTS W/CODES - 2.2L 1994 Toyota Celica 1994 ENGINE PERFORMANCE Toyota 2.2L Self-Diagnostics Celica INTRODUCTION If no faults were found while performing F - BASIC TESTING, proceed with self-diagnostics.
GF1A TRANSFER / 4WD / AWD: DYNAMIC TORQUE CONTROL AWD SYSTEM: SYSTEM DESCRIPTION; 2016 MY RAV4 [10/ /2016]
![GF1A TRANSFER / 4WD / AWD: DYNAMIC TORQUE CONTROL AWD SYSTEM: SYSTEM DESCRIPTION; 2016 MY RAV4 [10/ /2016]](/thumbs/92/109878214.jpg "GF1A TRANSFER / 4WD / AWD: DYNAMIC TORQUE CONTROL AWD SYSTEM: SYSTEM DESCRIPTION; 2016 MY RAV4 [10/ /2016]")
11/29/2017 Dynamic Torque System - System Description - [10/2015-08/2016] (Transfer Case) - ALLDATA 2016 Toyota Truck RAV4 4WD L4-2.5L (2AR-FE) Vehicle > Transmission and Drivetrain > Transfer Case > Description
Hesitation on Acceleration
L-SB-0033-08 Rev2 June 6, 2008 Service Category Engine/Hybrid System Section Engine Control Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2007 2012 LS460 2008 2012 LS600H REVISION NOTICE
COMBINATION METER BE 45 PARTS LOCATION
BE45 PARTS LOCATION BE46 BODY ELECTRICAL SYSTEM METER CIRCUIT BE47 TROUBLESHOOTING The table below will be useful for you in troubleshooting these electrical problems. The most likely causes of the malfunction
18. LIGHTS/METERS/ SERVICE INFORMATION TROUBLESHOOTING SWITCHES XL200
XL200 18. LIGHTS/METERS/ SWITCHES SERVICE INFORMATION 18-1 TROUBLESHOOTING 18-1 HEADLIGHT 18-2 TAIL/BRAKE LIGHT 18-3 TURN SIGNAL LIGHT 18-3 COMBINATION METER 18-4 IGNITION SWITCH 18-6 HANDLEBAR SWITCH
BE 66 COMBINATION METER PARTS LOCATION
BE66 PARTS LOCATION BE67 METER CIRCUIT BE68 No. 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 Airbag ECU Vehicle Speed Pulse Generator Door Courtesy Switch terminal 2 Fuse
DTC P0717 Input Speed Sensor Circuit No Signal
A750F AUTOMIC TRANSMISSION AUTOMIC TRANSMISSION SYSTEM 65 DTC P0717 Input Speed Sensor Circuit No Signal DESCRIPTION This sensor detects the rotation speed of the turbine which shows the input revolution
DIAGNOSTIC TROUBLE CODE CHART
DIAGNOSTIC TROUBLE CODE CHART NOTICE: When removing the part, turn the ignition switch OFF. 05319 HINT: Using SST 0984318040, connect the terminals Tc and CG of DLC3. If any abnormality is not found when
18. Light/Switch/Horn. Service Information. Troubleshooting. Light/Switch/Horn
18. Light/Switch/Horn Service Information 18-1 Troubleshooting 18-1 Headlight 18-2 Front Winker 18-2 Tail-Stop Light/Rear Winker 18-2 Meters(Measuring instruments) 18-3 Main Switch 18-4 Handle Bar Switch
TIRE PRESSURE AND MONITORING SYSTEMS (DIAGNOSTICS)
TIRE PRESSURE AND MONITORING SYSTEMS (DIAGNOSTICS) Basic Diagnostic Procedure 1. Basic Diagnostic Procedure A: PROCEDURE CAUTION: Remove foreign matter (dust, water, oil etc.) from the tire pressure monitoring
AUTOMATIC TRANSMISSION (DIAGNOSTICS) AT
AUTOMATIC TRANSMISSION (DIAGNOSTICS) AT Page 1. Basic Diagnostic Procedure...2 2. Check List for Interview...4 3. General Description...5 4. Electrical Components Location...7 5. Transmission Control Module
RS 44 SUPPLEMENTAL RESTRAINT SYSTEM HINT:
RS44 DIAGNOSIS INSPECTION SRS warning light check (a) Turn the ignition switch to ACC or ON and check that the SRS warning light lights up. (b) Check that the SRS warning light goes out after approx. 6
OPERATING LIGHT CONTROL RHEOSTAT DOES NOT CHANGE LIGHT BRIGHTNESS
05608 DIANOSTICS OPERATI LIHT CONTROL RHEOSTAT DOES NOT CHAE LIHT BRIHTNESS 05DKP01 WIRI DIARAM W W W Instrument Panel J/B 7 1R 6 1J 2 1N 11 1F W 27 C6 Combination Meter W Radio and Player 5 10 R3 R2 5
CRUISE CONTROL SPEED LIMITER Rev. 4.0
INSTALLATION f MANUAL CRUISE CONTROL & SPEED LIMITER AP900Series SL900Series 231.0004530 Rev. 4.0 1 2 CONTENTS: Chapters 1 Kit contents. 3 2 Tools required 4 3 Electronics module location... 5 4 Input
Diag. Code 22 Airbag Warning Light System Malfunction CIRCUIT DESCRIPTION ABT 71
SRS AIRBAG ABT71 Diag. Code 22 Airbag Warning Light System Malfunction CIRCUIT DESCRIPTION The airbag warning light is located on the combination meter. When the airbag system is normal, the airbag warning
Instrument Cluster TABLE OF CONTENTS
Instrument Cluster TABLE OF CONTENTS Instrument Cluster... - Instrument Cluster (GD)... - Tachometer, Speedometer... - Fuel Gauge, Coolant Temperature Gauge... - Display... - Adjusting the Instrument Cluster
BODY ELECTRICAL SYSTEM
BODY ELECTRICAL BODY ELECTRICAL SYSTEM PRECAUTION BODY ELECTRICAL SYSTEM Carefully to observe the following precautions when servicing the parts related to the body electrical system. 1. LIGHTING SYSTEM
DTC P0451(A) EVAPORATIVE EMISSION CONTROL SYSTEM PRESSURE SENSOR/SWITCH RANGE/PERFORMANCE
05210 DTC (A) EVAPORATIVE EMISSION CONTROL RANGE/PERFORMANCE 052NT12 DTC P0452 EVAPORATIVE EMISSION CONTROL LOW INPUT DTC P0453 EVAPORATIVE EMISSION CONTROL HIGH INPUT CIRCUIT DESCRIPTION The vapor pressure
ACTIVE TORQUE CONTROL 4WD SYSTEM
2008 DRIVELINE/AXLES Differential - RAV4 ACTIVE TORQUE CONTROL 4WD SYSTEM PRECAUTION 1. TROUBLESHOOTING PRECAUTION NOTE: Since the Active torque control system (4WD control system) may be influenced by
37. FATC (FULL AUTO TEMP. CONTROL) CIRCUIT 6810
5156 6810 37. FATC (FULL AUTO TEMP. CONTROL) CIRCUIT 6810 1) CONDENSOR FAN, AIR MIX MOTOR, SUN SENSOR, WATER TEMP SENSOR A. CONNECTOR INFORMATION 6810 5157 Connector Number (Pin Number, Color) Connecting
19. LIGHTS/METERS/SWITCHES
19. LIGHTS/METERS/ES SERVICE INFORMATION 19-1 REAR BRAKE LIGHT 19-6 TROUBLESHOOTING 19-2 CLUTCH 19-6 HEADLIGHT 19-3 HANDLEBAR 19-7 INSTRUMENT CASE 19-4 HORN 19-7 TURN SIGNAL/TAIL LIGHT BULB 19-5 IGNITION
CONTENTS MOTORCYCLE. ISSUE NO.: M DATE: Oct. 19, 2004 PAGE: 1 OF 9
MOTORCYCLE ISSUE NO.: M-4-0319 DATE: Oct. 19, 2004 PAGE: 1 OF 9 SUBJECT: CORRECTION AND ADDITIONAL INFORMATION OF THE SERVICE MANUAL APPLICABLE MODEL: LT-A700XK5 EFFECTIVE ENGINE OR FRAME NO.: REFERENCE:
CHECKING THE FUEL DELIVERY SYSTEM
2010 Dodge or Ram Truck RAM 1500 Truck 2WD V8-5.7L Vehicle > Powertrain Management > Fuel Delivery and Air Induction > Fuel Pump > Fuel Pressure > Testing and Inspection > Component Tests and General Diagnostics
DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED
0568 DTC P0300 RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED 057HV02 DTC P0301 CYLINDER 1 MISFIRE DETECTED DTC P0302 CYLINDER 2 MISFIRE DETECTED DTC P0303 CYLINDER 3 MISFIRE DETECTED DTC P0304 CYLINDER 4 MISFIRE
Technical Service BULLETIN
Technical Service BULLETIN December 22, 2005 Title: Models: 04 05 BR006-05 BRAKES TSB REVISION NOTICE: December 4, 2006: The Old Part Identification column of the Parts Identification table has been updated.
CHECK AND REPAIR BODY ELECTRICAL 9D-17. Speed Meter. Tacometer
CHECK AND REPAIR Speed Meter BODY ELECTRICAL 9D17 1. Using tester of speed meter, check error of allowance of speed meter and operation of tacometer. 2 4 6 8 1 12 3 +4 +4 +5 +5 +.5 14 16 18 2 22 YAD9D24
HEADLIGHT AND TAILLIGHT SYSTEM
BODY ELECTRICAL SYSTEM BE13 PARTS LOCATION BE14 BODY ELECTRICAL SYSTEM TROUBLESHOOTING The table below will be useful for you in troubleshooting these electrical problems. The most likely causes of the
HEADLIGHT AND TAILLIGHT
BE14 HEADLIGHT AND TAILLIGHT SYSTEM PARTS LOCATION BE15 TROUBLESHOOTING The table below will be useful for you in troubleshooting these electrical problems. The most likely causes of the malfunction are
SECTION 1 7 OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake
SECTION 1 7 OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch.............................................. 114 Automatic transmission.....................................
ENGINE IMMOBILISER SYSTEM
System Name Power Window Control System Sliding Roof System ENGINE IMMOBILISER SYSTEM PRECAUTION 1. PRECAUTION FOR DISCONNECTING BATTERY TERMINAL NOTICE: When disconnecting the negative () battery terminal,
Technical Bulletin AA 304. Central Locking System. m.y. 97
Technical Bulletin Subject: Model(s): Central Locking System Cabriolet m.y. 97 Group: Number: Date: 01 96 11 Nov. 29, 1996 The following Repair Manual pages are new and will be integrated with the next
1999 Toyota RAV ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4
1999 ACCESSORIES & EQUIPMENT Cruise Control Systems - RAV4 DESCRIPTION WARNING: Deactivate air bag system before performing any service operation. See AIR BAG RESTRAINT SYSTEMS article. DO NOT apply electrical
HOW TO PERFORM VEHICLE IDENTIFICATION NUMBER (VIN) WRITING
HOW TO PERFORM VEHICLE IDENTIFICATION NUMBER (VIN) WRITING CAUTION: The F.A.S.T-Key (Free-hand Advanced Security Transmitter) is described as the Keyless Operation System (KOS). Follow the procedure below
Layout Diagrams. Section CONTENTS. General Layout Diagram Floor / Roof Engine Compartment Door
1-1 Section 1 Layout Diagrams CONTENTS General Layout Diagram...1-3 Engine Compartment...1-4 Engine / Transmission...1-6 Floor / Roof...1-16 Door...1-18 Boot Compartment...1-20 Instrument Panel...1-10
LIGHTS/SWITCHES LIGHTS/SWITHCES MXU 500
20 LIGHTS/SWITHCES SERVICE INFORMATION------------------------------------------------ 20-1 BULBS REMOVAL--------------------------------------------------------- 20-2 HORN (ON ROAD) ---------------------------------------------------------
VSC TRAC Warning Light Remains ON
KE CONTOL VEHICLE STILITY CONTOL SYSTEM C 47 VSC TC Warning Light emains ON DESCIPTION When the skid control ECU stores DTCs, the VSC and TC functions are deactivated, the VSC TC warning light comes on
DTC P0110/24 Intake Air Temp. Circuit Malfunction
DI30 EINE (JZGE) DI63Q06 DTC P00/4 Temp. Circuit Malfunction CIRCUIT DESCRIPTI Resistance k (Fig. ) 30 0 0 5 3 0.5 0.3 0. 0. Acceptable 0 0 0 40 60 80 00 ( 4) 3 68 04 40 76 Temp. C ( F) The intake air
TIRE PRESSURE WARNING SYSTEM. 1. General 4RUNNER - NEW FEATURES
TIRE PRESSURE WARNING SYSTEM 1. General A direct-sensing type tire pressure warning system has been newly adopted as standard equipment on all 04 4Runner models. If the vehicle continues to be driven with
HOW TO PROCEED WITH TROUBLESHOOTING
4 TER TER / GAUGE SYSTEM HOW TO PROCEED WITH TROUBLESHOOTING 1 VEHICLE BROUGHT TO WORKSHOP 2 CUSTOR PROBLEM ANALYSIS 3 PROBLEM SYMPTOM CONFIRMATION 4 PROBLEM SYMPTOMS TABLE 5 CIRCUIT INSPECTION 6 REPAIR
DIAGNOSIS AND TESTING
307-05-1 Automatic Transaxle/Transmission External Controls 307-05-1 DIAGNOSIS AND TESTING Visual Inspection Chart External Controls Mechanical Electrical Refer to Wiring Diagrams Cell 37 for schematic
CANBUS Emulator Mini V1.x. Overview - Installation and Operating Instructions
CANBUS Emulator Mini V1.x Overview - Installation and Operating Instructions Contents Overview... 2 Installation... 3 Basic Install... 3 With optional speed sensor input and reverse signal input... 3 Operation...