Taillight Relay Circuit
|
|
|
- Amos Young
- 6 years ago
- Views:
Transcription
1 GHTI GHTI SYSTEM 63 Taillight Relay Circuit DESCRIPTION The headlight dimmer switch sends a signal to the main body ECU. WIRI DIAGRAM Main Body ECU TAIL To Battery TAIL TRLY Outer Rear View Mirror Illumination Light LH Outer Rear View Mirror Illumination Light RH Taillight LH Taillight RH License Plate Light Front Turn Signal Light LH Front Turn Signal Light RH B389E0 INSPECTION PROCEDURE PERFORM ACTIVE TEST BY INTELGENT TESTER (ILLUMI OUTPUT) BODY (a) (b) (d) Connect the intelligent tester with CAN VIM to the DLC3. Turn the ignition switch ON. Turn the intelligent tester main switch on. Select the item below in the ACTIVE TEST and then check the relay operation. Item Test Details/ Display (Range) Diagnostic Note ILLUMI OUTPUT Illuminated Entry System ON/OFF -
2 64 GHTI GHTI SYSTEM Result Result No illumination lights illuminate Front turn signal light does not illuminate Taillight or license plate light does not illuminate Outer rear view mirror illumination light does not illuminate Proceed to A B C D E B C D E Go to step Go to step 5 Go to step 7 Go to step 0 A PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE INSPECT FUSE (TAIL FUSE) (a) Remove the TAIL fuse from the main body ECU. (b) Measure the resistance. resistance: Below Ω Reinstall the TAIL fuse. REPLACE FUSE 3 INSPECT TAIL RELAY (a) Remove the TAIL relay from the main body ECU. (b) Measure the resistance. resistance Battery kω or higher 3-5 Reinstall the TAIL relay. Below Ω (When battery voltage is applied between terminals and ) REPLACE TAIL RELAY Ohmmeter E09078E06
3 GHTI GHTI SYSTEM 65 4 CHECK HARNESS AND (BATTERY - TAIL RELAY) Main Body ECU (a) Remove the TAIL relay from the main body ECU. (b) Measure the resistance. resistance Condition - Body ground Always to 4 V 5 - Body ground Always to 4 V Reinstall the TAIL relay. B3893E0 REPLACE MAIN BODY ECU 5 INSPECT BULB (FRONT TURN SIGNAL GHT) Front Turn Signal Light* (a) Remove the front turn signal lights. front turn signal light illuminates. Positive battery - Terminal Negative battery - Terminal Front turn signal light illuminates *: LH or RH B36088E0 Reinstall the front turn signal lights. REPLACE BULB
4 66 GHTI GHTI SYSTEM 6 CHECK HARNESS AND (MAIN BODY ECU - FRONT TURN SIGNAL GHT) Wire Harness Side: Front Turn Signal Light Connector * A6 * A0 *: LH *: RH Main Body ECU Connector B (a) Disconnect the A6 and A0 front turn signal light connectors. (b) Disconnect the B main body ECU connector. Measure the resistance. resistance (d) (e) A6- - B-9 Below Ω A0- - B- Below Ω A6- or B-9 - Body ground 0 kω or higher A0- or B- - Body ground 0 kω or higher Reconnect the front turn signal light connectors. Reconnect the main body ECU connector B389E0 (FRONT TURN SIGNAL GHT - BODY GROUND) 7 INSPECT BULB (TAILGHT) Taillight* (a) Remove the taillights. taillight illuminates. 3 Positive battery - Terminal Negative battery - Terminal Taillight illuminates *: LH or RH Reinstall the taillights. B4038E0 REPLACE BULB
5 GHTI GHTI SYSTEM 67 8 INSPECT BULB (CENSE PLATE GHT) License Plate Light (a) Remove the license plate light. license plate light illuminates. Positive battery - Terminal Negative battery - Terminal Licence plate light illuminates Reinstall the license plate light. B3894E0 REPLACE BULB 9 CHECK HARNESS AND (MAIN BODY ECU - TAILGHT, CENSE PLATE GHT) Wire Harness Side: Taillight Connector L L4 * * 3 *: LH *: RH License Plate Light Connector (a) Disconnect the L and L4 taillight connectors. (b) Disconnect the S license plate light connector. Disconnect the F main body ECU connector. (d) Measure the resistance. resistance F-3 - L- Below Ω F-3 - L4- Below Ω F-3 - S- Below Ω F-3 or L- or Body ground 0 kω or higher F-3 or L4- or Body ground 0 kω or higher F-3 or S- or Body ground 0 kω or higher S (e) (f) (g) Reconnect the taillight connectors. Reconnect the license plate light connector. Reconnect the main body ECU connector. Main Body ECU Connector F B3895E0 (TAILGHT, CENSE PLATE GHT - BODY GROUND)
6 68 GHTI GHTI SYSTEM 0 INSPECT BULB (OUTER REAR VIEW MIRROR ILLUMINATION GHT) Outer Rear View Mirror Assembly* (a) Remove the outer rear view mirror assembly. outer rear view mirror illumination light illuminates Positive battery - Terminal Negative battery - Terminal Outer rear view mirror illumination light illuminates *: LH and RH Reinstall the outer rear view mirror assembly. B3896E0 REPLACE BULB CHECK HARNESS AND (MAIN BODY ECU - OUTER REAR VIEW MIRROR ILLUMINATION GHT) Wire Harness Side: Outer Rear View Mirror Assembly Connector H G * * Main Body ECU Connector L *: LH *: RH (a) Disconnect the H and G outer rear view mirror assembly connectors. (b) Disconnect the L main body ECU connector. Measure the resistance. resistance (d) (e) L-5 - H- Below Ω L-5 - G- Below Ω Reconnect the outer rear view mirror assembly connector. Reconnect the main body ECU connector B3897E0 (OUTER REAR VIEW MIRROR ILLUMINATION GHT - BODY GROUND)
LIGHTING SYSTEM PRECAUTION LI 1
System Name Power Window Control System GHTING GHTING SYSTEM GHTING SYSTEM PRECAUTION 1 1. PRECAUTION FOR DISCONNECTING BATTERY CABLE NOTICE: FOR INITIAZATION: When disconnecting the cable from the negative
THEFT DETERRENT SYSTEM
THEFT DETERRENT THEFT DETERRENT SYSTEM 1 System Name Power Window Control System THEFT DETERRENT SYSTEM PRECAUTION NOTICE: For initialization: When disconnecting the cable from the negative (-) battery
VSC OFF Indicator Light Remains ON
6 RAKE CONTROL VEHICLE STAILITY CONTROL SYSTEM VSC OFF Indicator Light Remains ON DESCRIPTION When the rear differential is locked or during the WD mode, VSC control turns off and the VSC OFF indicator
DIAGNOSTIC TROUBLE CODE CHART
18 Cruise Control System DIAGNOSTIC TROUBLE CODE CHART If a trouble code is indicated while checking DTCs, inspect the listed for that code in the table below, and proceed to the applicable page. DTC No.
TO INDEX LIGHTING SIDE TURN SIGNAL LIGHT ASSEMBLY LH TAILLIGHT (REAR COMBINATION LIGHT) ASSEMBLY LH LICENSE PLATE LIGHT ASSEMBLY
TO INDEX BODY AND ELECTRICAL GHTING GHTING SYSTEM PRECAUTIONS.............................................. OPERATION CHECK......................................... BASIC INSPECTION..........................................
CRUISE CONTROL SYSTEM
Negative (-) Battery Terminal CRUISE CONTROL CRUISE CONTROL SYSTEM Cable System name METER / GAUGE SYSTEM D033496E01 CRUISE CONTROL SYSTEM PRECAUTION 1 1. DISCONNECT AND RECONNECT CABLE OF NEGATIVE BATTERY
ON-VEHICLE INSPECTION
32 SUSPENSION CONTROL AIR SUSPENSION SYSTEM ON-VEHICLE INSPECTION 1. CHECK FLUID LEAKAGE Check the connections of tube and parts for fluid leakage. : Supply parts only C099149E01 SUSPENSION CONTROL AIR
DRL RELAY CIRCUIT CIRCUIT DESCRIPTION
051562 DIAGNOSTICS 05ETR02 DRL RELAY CIRCUIT CIRCUIT DESCRIPTION The multiplex network body ECU controls DRL No.2, No. and No.4 relays. The headlamp (High) is connected in serial when the daytime running
DTC C1735/35 Exhaust Solenoid Valve Circuit
8 DTC C7/ DTC C74/4 Rear Height Control Gate Solenoid Valve Circuit Malfunction Rear Height Control Leveling Solenoid Valve Circuit Malfunction DTC C75/5 Exhaust Solenoid Valve Circuit DTC C744/44 Tank
Symptom Suspected Area See page Ignition switch is not set to each position. 11.Ignition switch BE 14
BE2 BODY ELECTRICAL PROBLEM SYMPTOMS TABLE IGNITION SWITCH AND KEY UNLOCK WARNING SWITCH BE0ON18 Ignition switch is not set to each position. 11.Ignition switch BE14 Key unlock warning system does not
CRUISE CONTROL SYSTEM
CRUISE CONTROL SYSTEM CONTROL SYSTEM PARTS LOCATION CRUISE CONTROL CRUISE CONTROL SYSTEM 1 ENGINE ROOM R/B AND J/B MAIN BODY ECU (INSTRUMENT PANEL J/B) B142328E05 2 CRUISE CONTROL CRUISE CONTROL SYSTEM
ECM Power Source Circuit
GR-FE EINE CONTROL SYSTEM SFI SYSTEM 389 ECM Power Source Circuit DCRIPTION When the ignition switch is turned ON, the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal
MULTIPLEX COMMUNICATION SYSTEM
MULTIPLEX COMMUNICATION SYSTEM PRECAUTION 1 1. DISCONNECT AND RECONNECT CABLE OF NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following
METER / GAUGE SYSTEM (for Sedan)
TER TER / GAUGE SYSTEM (for Sedan) TER / GAUGE SYSTEM (for Sedan) BODY ELECTRICAL PARTS LOCATION 1 REAR DOOR COURTESY SWITCH RH REAR DOOR COURTESY SWITCH LH FRONT DOOR COURTESY SWITCH RH BRAKE FLUID LEVEL
Trouble in Passenger Airbag ON / OFF Indicator
8 SUPPLEMENTAL RESTRAINT SYSTEM OCCUPANT CLASSIFICATION SYSTEM Trouble in Passenger Airbag ON / OFF Indicator DESCRIPTION The occupant classification system detects the front passenger seat condition and
ON-VEHICLE INSPECTION
452 DLC3 CAN VIM Intelligent Tester G035612E02 ON-VEHICLE INSPECTION 1. INSPECT THROTTLE BODY (a) Listen to the throttle control motor operating sounds. (1) Turn the ignition switch to ON. (2) When pressing
FUEL PUMP CONTROL CIRCUIT
05245 05DK00 FUEL PUMP CONTROL CIRCUIT CIRCUIT DESCRIPTION In the diagram below, when the engine is cranked, current flows from terminal ST2 of the ignition switch to the starter relay coil and also current
BE 30 BODY ELECTRICAL SYSTEM. Combination Meter COMBINATION METER. Parts Location
BE30 BODY ELECTRICAL SYSTEM COMBINATION METER Parts Location BODY ELECTRICAL SYSTEM BE31 Meter Circuit (w/o Tachometer) No. 2 7 9 12 1 2 3 5 7 9 3 Wiring connector side ETC Pattern select switch A/T Oil
5/15/2018 2GR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: Fuel Pump Control Circuit (2007 RX350) 2007 Lexus RX350 MotoLogic
5/15/2018 2GR-FE EINE CONTROL SYSTEM: SFI SYSTEM: Fuel Pump Control Circuit (2007 RX350) 2007 Lexus RX350 MotoLogic 2007 RX350 Report a problem with this article Last Modified: 2010-10-20 00:00:00 J From:200601
INTELLIGENT AFS (Adaptive Front-lighting System) 1. General BE-30 BODY ELECTRICAL - LIGHTING
BE-30 INTELLIGENT AFS (Adaptive Front-lighting System) 1. General An intelligent AFS (Adaptive Front-lighting System) is used in order to ensure a wide Lo beam lighting area and realize excellent visibility
HEADLIGHT AND TAILLIGHT SYSTEM
BE13 PARTS LOCATION BE14 BODY ELECTRICAL SYSTEM TROUBLESHOOTING The table below will be useful for you in troubleshooting these electrical problems. The most likely causes of the malfunction are shown
Symptom Suspect Area See page. 11.Ignition Switch 12.Power Source Circuit. Symptom Suspect Area See page
BE2 PROBLEM SYMPTOMS TABLE IGNITION SWITCH: BE18204 Ignition switch is not set to each position. KEY UNLOCK WARNING SWITCH: 11.Ignition Switch 12.Power Source Circuit BE15 Key unlock warning system does
HEADLIGHT AND TAILLIGHT SYSTEM
BE BODY ELECTRICAL LOCATION E/G Room J/B No. HEAD LH Fuse (w/o Daytime Running Light) HEAD RH Fuse (w/o Daytime Running Light) HEAD LH (UPR) Fuse (w/ Daytime Running Light) HEAD RH (UPR) Fuse (w/ Daytime
No Answer-Back (Hazard Warning Light and Wireless Door Lock Buzzer)
56 No nswer-ack (Hazard Warning Light and Wireless Door Lock uzzer) DESCRIPTION If there is no answer-back of the hazard warning lights and wireless door lock buzzer while the wireless control function
DIAGNOSIS. https://mitsubishitechinfo.com/data/st41/2003/m /html/m of 6 1/17/2016 5:45 PM
1 of 6 1/17/2016 5:45 PM DIAGNOSIS Required Special Tools: MB991223: Harness Set MB991502: Scan Tool (MUT-II) MB991862: SWS monitor kit STEP 1. Use scan tool MB991502 to select "ECU COMM CHK" on the SWS
DTC C1252 / 52 Hydraulic Brake Booster Pump Motor ON Time Abnormally Long
DIAGNOSTICS DI0 DI6BT08 DTC C / Hydraulic Brake Booster Pump Motor ON Time Abnormally Long CIRCUIT DESCRIPTION DTC No. DTC Detecting Condition Trouble Area C / After the ignition switch has been turned
SUPPLEMENTAL RESTRAINT SYSTEM AIRBAG SYSTEM
262 SUPPLEMENTL RESTRINT SYSTEM IRBG SYSTEM DTC B1825/56 DTC B1826/56 DTC B1827/56 DTC B1828/56 Short in Circuit Open in Circuit Short to GND in Front Passenger Side - Side Squib Circuit Short to B+ in
DRL RELAY CIRCUIT CIRCUIT DESCRIPTION WIRING DIAGRAM
05704 05HJH0 DRL REL CIRCUIT CIRCUIT DESCRIPTION The multiplex network body ECU controls the DRL No.4 relay. The DRL No.4 relay connects the daytime running light relay and the headlamp during DRL operation.
POWER MIRROR CONTROL SYSTEM
RROR POWER RROR CONTROL SYSTEM POWER RROR CONTROL SYSTEM BODY RROR PARTS LOCATION 1 DRIVER SIDE JUNCTION BLOCK - ACC FUSE - AM2 FUSE - ACC-B FUSE OUTER REAR VIEW RROR RH OUTER REAR VIEW RROR LH ACC RELAY
DTC B1156/B1157/15 Front Airbag Sensor (RH) Malfunction
DI309 DI6PW03 DTC B1156/B1157/15 Malfunction CIRCUIT DESCRIPTION The front airbag sensor (RH) circuit consists of the airbag sensor assembly and front airbag sensor (RH). For details of the function of
4/17/2018 2AZ-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0031,P0032: Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)
2007 Camry LE (L4) Report a problem with this article Last Modified: 2010-6-11 00:00:00 C From:200601 Model Year: 2007 Model: Camry Doc ID: RM000000WC101DX Engine Family: 2AZ-FE Body Type: 4Dr. Sedan VDS:
CRUISE CONTROL SYSTEM
CRUISE CONTROL CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM PRECAUTION 1 1. NOTICE FOR INITIALIZATION NOTICE: When the cable of the negative () battery terminal is disconnected, initialize the following
BE 46 BODY ELECTRICAL SYSTEM COMBINATION METER COMBINATION METER PARTS LOCATION
BE46 PARTS LOCATION BE47 METER CIRCUIT (4AFE, 5SFE Engine) No. 1 2 3 4 5 6 8 9 10 Wiring connector side Brake Fluid Level Warning Switchterminal 1, and Parking Brake Switch Igniter DOME Fuse Door Courtesy
WIPER AND WASHER SYSTEM
WIPER AND WASHER WIPER AND WASHER SYSTEM WIPER AND WASHER SYSTEM PRECAUTION 1 NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable
HEADLIGHT AND TAILLIGHT
BE14 HEADLIGHT AND TAILLIGHT SYSTEM PARTS LOCATION BE15 TROUBLESHOOTING The table below will be useful for you in troubleshooting these electrical problems. The most likely causes of the malfunction are
BRAKE CONTROL VEHICLE STABILITY CONTROL SYSTEM. DTC No. DTC Detecting Conditions Trouble Areas
70 RKE CONTROL VEHICLE STILITY CONTROL SYSTEM DTC C0210/33 Rear Speed Sensor RH Circuit DTC C0215/34 Rear Speed Sensor LH Circuit DTC C1238/38 DTC C1239/39 DTC C1273/73 DTC C1274/74 DTC C1277/77 DTC C1278/78
DTC C0210/33 Rear Speed Sensor RH Circuit. DTC C0215/34 Rear Speed Sensor LH Circuit
RKE CONTROL VEHICLE STILITY CONTROL SYSTEM 65 DTC C0210/33 Rear Speed Sensor RH Circuit DTC C0215/34 Rear Speed Sensor LH Circuit DTC C1238/38 DTC C1239/39 Foreign Object is ttached on Tip of Rear Speed
DTC B1140/32 Side Airbag Sensor Assembly (RH) Malfunction
DI342 DIAGNOSTICS DI6ZW03 DTC B1140/32 Side (RH) Malfunction CIRCUIT DESCRIPTI The side airbag sensor assembly (RH) consists of the safing sensor, diagnosis circuit and lateral deceleration sensor, etc.
ONLY WIRELESS CONTROL FUNCTION DOES NOT OPERATE (PREPARE NEW OR NORMAL TRANSMITTER OF THE SAME TYPE VEHICLE)
DIAGNOSTICS ONLY WIRELESS CONTROL FUNCTION DOES NOT OPERATE (PREPARE NEW OR NORMAL TRANSMITTER OF THE SAME TYPE VEHICLE) 05679 05DLG01 CIRCUIT DESCRIPTION The door control receiver receives a signal from
CRUISE CONTROL SYSTEM
CRUISE CONTROL CRUISE CONTROL SYSTEM CRUISE CONTROL SYSTEM PRECAUTION 1 1. HANDLING PRECAUTION FOR CRUISE CONTROL SYSTEM (a) Turn the cruise control main switch OFF when not using the cruise control system.
OPERATING LIGHT CONTROL RHEOSTAT DOES NOT CHANGE LIGHT BRIGHTNESS
05608 DIANOSTICS OPERATI LIHT CONTROL RHEOSTAT DOES NOT CHAE LIHT BRIHTNESS 05DKP01 WIRI DIARAM W W W Instrument Panel J/B 7 1R 6 1J 2 1N 11 1F W 27 C6 Combination Meter W Radio and Player 5 10 R3 R2 5
ENGINE IMMOBILISER SYSTEM
System Name Power Window Control System Sliding Roof System ENGINE IMMOBILISER SYSTEM PRECAUTION 1. PRECAUTION FOR DISCONNECTING BATTERY TERMINAL NOTICE: When disconnecting the negative () battery terminal,
Only Wireless Control Function is Inoperative
58 DOOR LOCK WIRELESS DOOR LOCK CTROL SYSTEM Only Wireless Control Function is Inoperative DESCRIPTI The door control receiver receives signals from the transmitter and sends these signals to the main
ELECTRONIC POWER STEERING SYSTEM
POWER STEERING ELECTRONIC POWER STEERING SYSTEM 1 ELECTRONIC POWER STEERING SYSTEM PRECAUTION 1. HANDLING PRECAUTION (a) When handling the electronic parts: Avoid any impact to electronic parts such as
ELECTRICAL DIAGNOSTICS & OPERATION
Operation Function: Provides power to the headlights, tail lights, hazard lights, work light and dash lights in different combinations depending upon the position the light switch is placed in. Operating
DTC P0100 Mass or Volume Air Flow Circuit. DTC P0102 Mass or Volume Air Flow Circuit Low Input. DTC P0103 Mass or Volume Air Flow Circuit High Input
94 TR-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P0100 Mass or Volume Air Flow Circuit DTC P010 Mass or Volume Air Flow Circuit Low Input DTC P0103 Mass or Volume Air Flow Circuit High Input DCRIPTION The Mass
BE 66 COMBINATION METER PARTS LOCATION
BE66 PARTS LOCATION BE67 METER CIRCUIT BE68 No. 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 Airbag ECU Vehicle Speed Pulse Generator Door Courtesy Switch terminal 2 Fuse
Model Year Start: 2008 Model: GX470 Prod Date Range: [07/2007 ]
![Model Year Start: 2008 Model: GX470 Prod Date Range: [07/2007 ]](/thumbs/87/96773417.jpg "Model Year Start: 2008 Model: GX470 Prod Date Range: [07/2007 ]")
Last Modified: 7 27 2016 6.6 C Doc ID: RM000000YDP015X Model Year Start: 2008 Model: GX470 Prod Date Range: [07/2007 ] Title: 2UZ FE EINE CONTROL SYSTEM: SFI SYSTEM: P0100,P0102,P0103; Mass Air Flow Circuit
TURN SIGNAL AND HAZARD WARNING SYSTEM
BE68 BODY ELECTRICAL SYSTEM TURN SIGNAL AND HAZARD WARNING SYSTEM DESCRIPTION The component parts of this system and their function are as shown in the following table. Parts Name Function Turn Signal
DTC P0100 Mass or Volume Air Flow Circuit. DTC P0102 Mass or Volume Air Flow Circuit Low Input. DTC P0103 Mass or Volume Air Flow Circuit High Input
GR-FE EINE CONTROL SYSTEM SFI SYSTEM 95 DTC P000 Mass or Volume Air Flow Circuit DTC P00 Mass or Volume Air Flow Circuit Low Input DTC P003 Mass or Volume Air Flow Circuit High Input DCRIPTION The Mass
STEERING COLUMN VARIABLE GEAR RATIO STEERING SYSTEM CALIBRATION. (a) Check for DTC. Result. DTC C1515/15 is not output DTC C1515/15 is output
56 STEERING COLUMN VRILE GER RTIO STEERING SYSTEM CLIRTION 1. VGRS SYSTEM CLIRTION PROCEDURE (USING SST CHECK WIRE) Use this procedure to center the steering wheel position if: VGRS actuator has been replaced
DTC C2121/21 No Signal from Transmitter ID1 in Main Mode. DTC C2122/22 No Signal from Transmitter ID2 in Main Mode
38 TIRE ND WHEEL TIRE PRESSURE WRNING SYSTEM DTC C2121/21 No Signal from Transmitter ID1 in Main Mode DTC C2122/22 No Signal from Transmitter ID2 in Main Mode DTC C2123/23 No Signal from Transmitter ID3
ENGINE IMMOBILISER SYSTEM
ENGINE IMMOBILISER ENGINE IMMOBILISER SYSTEM 1 ENGINE IMMOBILISER SYSTEM PRECAUTION NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the
HEADLIGHT AND TAILLIGHT SYSTEM
BODY ELECTRICAL SYSTEM BE13 PARTS LOCATION BE14 BODY ELECTRICAL SYSTEM TROUBLESHOOTING The table below will be useful for you in troubleshooting these electrical problems. The most likely causes of the
DTC B1141/33 Side and Curtain Shield Airbag Sensor Assembly (LH) Malfunction
DTC B1141/33 and Curtain Shield Assembly (LH) Malfunction 05719 05A1N01 CIRCUIT DESCRIPTION The side airbag sensor assy LH circuit consists of the diagnosis circuit and lateral deceleration sensor, etc.
DTC P0617 STARTER RELAY CIRCUIT HIGH
0534 DTC P067 STARTER RELAY CIRCUIT HIGH 05DJY0 MONITOR DESCRIPTION While the engine is being cranked, the battery positive voltage is applied to terminal STA of the ECM. If the ECM detects the starter
Only Wireless Control Function is Inoperative
49 Only Wireless Control Function is Inoperative DESCRIPTI The door control receiver receives signals from the transmitter and sends these signals to the multiplex network body ECU. The multiplex network
Throttle Actuator Control Motor Current Range / Performance
TR-FE EINE CONTROL SYSTEM SFI SYSTEM 99 DTC P8 Control Motor Current Range / Performance DCRIPTION The ETCS (Electronic Throttle Control System) has a dedicated power supply circuit. The voltage () is
DTC C0273/13 OPEN CIRCUIT IN ABS MOTOR RELAY CIRCUIT DTC C0274/14 SHORT CIRCUIT IN ABS MOTOR RELAY CIRCUIT
0804 DTC C0273/13 OPEN CIRCUIT IN ABS MOTOR RELAY CIRCUIT 0F1Q09 DTC C0274/14 SHORT CIRCUIT IN ABS MOTOR RELAY CIRCUIT DTC C1361/91 SHORT CIRCUIT IN ABS MOTOR FAIL SAFE RELAY CIRCUIT CIRCUIT DESCRIPTION
DTC C2121/21 No Signal from Transmitter ID1. DTC C2122/22 No Signal from Transmitter ID2. DTC C2123/23 No Signal from Transmitter ID3
TIRE ND WHEEL TIRE PRESSURE WRNI SYSTEM 33 DTC C2121/21 No Signal from Transmitter ID1 DTC C2122/22 No Signal from Transmitter ID2 DTC C2123/23 No Signal from Transmitter ID3 DTC C2124/24 No Signal from
LIGHTS/SWITCHES LIGHTS/SWITHCES MXU 500
20 LIGHTS/SWITHCES SERVICE INFORMATION------------------------------------------------ 20-1 BULBS REMOVAL--------------------------------------------------------- 20-2 HORN (ON ROAD) ---------------------------------------------------------
STARTING SYSTEM (for 0.8 kw Type) > PARTS LOCATION
STARTING SYSTEM (for 0.8 kw Type) > PARTS LOCATION 1 / 2 2 / 2 STARTING SYSTEM (for 0.8 kw Type) > SYSTEM DIAGRAM STARTING SYSTEM (for 0.9 kw Type) > PARTS LOCATION 1 / 2 2 / 2 STARTING SYSTEM
DTC P2440 SECONDARY AIR INJECTION SYSTEM SWITCHING VALVE STUCK OPEN BANK1 DTC P2441 SECONDARY AIR INJECTION SYSTEM SWITCHING VALVE STUCK CLOSE BANK1
DIAGNOSTICS SFI SYSTEM (2ZZ GE) (May, 2003) DTC P2440 SECONDARY AIR INJECTION SYSTEM SWITCHI VALVE STUCK OPEN BANK1 05 575 05DWI 01 DTC P2441 SECONDARY AIR INJECTION SYSTEM SWITCHI VALVE STUCK CLOSE BANK1
Short to GND in CAN Bus Line
N COMMUNITION N COMMUNITION SYSTEM 55 Short to GND in N Bus Line DESCRIPTION A short to GND is suspected in the N bus line when there is continuity between terminals and 6 (NH) or terminals and 14 (NL)
DTC C1238/38 FOREIGN MATTER IS ATTACHED ON TIP OF RIGHT REAR SENSOR DTC C1239/39 FOREIGN MATTER IS ATTACHED ON TIP OF LEFT REAR SENSOR
DIAGNOSTICS DTC C00/33 RIGHT REAR SPEED SENSOR 05795 05H3B03 DTC C05/34 LEFT REAR SPEED SENSOR DTC C38/38 FOREIGN MATTER IS ATTACHED ON TIP OF RIGHT REAR SENSOR DTC C39/39 FOREIGN MATTER IS ATTACHED ON
DTC B1140/32 Side Airbag Sensor Assy (RH) Malfunction
DI428 DIAGNOSTICS DI9HU01 DTC B1140/32 Side (RH) Malfunction CIRCUIT DESCRIPTION The side airbag sensor assy (RH) consists of the safing sensor, diagnosis circuit and lateral deceleration sensor, etc.
1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITS
841006 013 Fuse and relay 841006 1. CAUTIONS WHEN WORKING ON ELECTRICAL UNITS Remove the negative battery cable from the battery in advance when working on electrical units. Make sure to turn "OFF" the
Shift Solenoid "A" Performance (Shift Solenoid Valve S1)
78 DTC P0751 Shift Solenoid "A" Performance (Shift Solenoid Valve S1) DESCRIPTION The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st,
DTC B1141/33 Side Airbag Sensor Assembly (LH) Malfunction
DI350 DI6ZX04 DTC B1141/33 Side (LH) Malfunction CIRCUIT DESCRIPTI The side airbag sensor assembly (LH) consists of the safing sensor, diagnosis circuit and lateral deceleration sensor, etc. It receives
Headlight Assembly. Headlight Assembly
Headlight Assembly Headlight Assembly Headlight Assembly HEADLIGHT ASSEMBLY REMOVAL Use the same procedures for the RH and LH sides. The procedures listed below are for the LH side. 1. DISCONNECT CABLE
Exterior Lighting Systems Description and Operation. Exterior Lamps. The exterior lighting system consists of the following lamps: The headlamps
Exterior Lighting Systems Description and Operation Exterior Lamps The exterior lighting system consists of the following lamps: The headlamps The daytime running lamps (DRL) The front fog lamps The park,
DTC P0100 MASS OR VOLUME AIR FLOW CIRCUIT DTC P0102 MASS OR VOLUME AIR FLOW CIRCUIT LOW INPUT DTC P0103 MASS OR VOLUME AIR FLOW CIRCUIT HIGH INPUT
0564 DIAGNOSTICS DTC P0100 MASS OR VOLUME AIR FLOW CIRCUIT 059VF10 DTC P0102 MASS OR VOLUME AIR FLOW CIRCUIT LOW INPUT DTC P0103 MASS OR VOLUME AIR FLOW CIRCUIT HIGH INPUT CIRCUIT DESCRIPTION The MAF (Mass
DTC B1140/32 SIDE AIRBAG SENSOR ASSY (RH) MALFUNCTION
05644 DTC B1140/32 SIDE AIRBAG SENSOR ASSY (RH) MALFUNCTION 055Z603 CIRCUIT DESCRIPTION The side airbag sensor assy (RH) consists of the diagnosis circuit and lateral deceleration sensor, etc. It receives
DTC P0617 Starter Relay Circuit High
GR-FE EINE CONTROL SYSTEM SFI SYSTEM 69 DTC P067 Starter Relay Circuit High DCRIPTION While the engine is being cranked, the positive battery voltage is applied to terminal of the ECM. If the ECM detects
POWER SOURCE (Current Flow Chart)
The chart below shows the route by which current flows from the battery to each electrical source (Fusible Link, Circuit Breaker, Fuse, etc.) and other parts. The next page and following pages show the
LIGHTING. GROUP 54Ac. Continued on next page. 54Ac-1 CONTENTS. GENERAL INFORMATION...54Ac-5. SERVICE SPECIFICATIONS...54Ac-7. SPECIAL TOOLS...
54Ac-1 GROUP 54Ac LIGHTING CONTENTS GENERAL INFORMATION...54Ac-5 SERVICE SPECIFICATIONS...54Ac-7 SPECIAL TOOLS...54Ac-8...54Ac-11 STANDARD FLOW OF DIAGNOSTIC TROUBLESHOOTING...54Ac-11 DIAGNOSTIC FUNCTION...54Ac-11
HOW TO PROCEED WITH TROUBLESHOOTING
2005 BRAKES Anti-Lock Brake System With Electronic Brake Force Distribution (EBD) - Diagnostics - RAV4 HOW TO PROCEED WITH TROUBLESHOOTING Troubleshoot in accordance with the following procedures. Fig.
DTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1)
05114 DIAGNOSTICS 05CRQ04 DTC P0134 OXYGEN SENSOR CIRCUIT NO ACTIVITY DETECTED (BANK 1 SENSOR 1) CIRCUIT DESCRIPTION Refer to DTC P0130 on page 0596. DTC No. DTC Detecting Condition Trouble Area After
DTC P0657 Actuator Supply Voltage Circuit / Open
301 DTC P0657 Actuator Supply Voltage Circuit / Open DCRIPTION The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is functioning properly. The output voltage
Rear Body 40D 156A 24 17A 151 3D. 8A,8B,8C under hood light. Horn Relay 91
fuse box as viewed from the wire entry side Mating connector is plugged into Power Accessory connector 40D Rear Body 19 18 9B 30 LH Courtesy Light 40A,D 4D, 43 156B,C 16 16A 4C 3D 3C 16A 3G 4B 3G 116 4A&130
2003 Crown Victoria/Grand Marquis/Marauder Workshop Manual
Page 1 of 9 SECTION 413-00: Instrument Cluster and Panel Illumination 2003 Crown Victoria/Grand Marquis/Marauder Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 02/25/2004 Instrument Cluster
2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
385 P2237 / Open (Bank 1 Sensor 1) P2238 Low (Bank 1 Sensor 1) P2239 High (Bank 1 Sensor 1) P2240 P2241 / Open (Bank 2 Sensor 1) Low (Bank 2 Sensor 1) P2242 High (Bank 2 Sensor 1) P2252 Low (Bank 1 Sensor
SRS Warning Light Remains ON
232 SUPPLEMENTL RESTRINT SYSTEM IRG SYSTEM S Warning Light Remains ON DESRIPTION The S warning light is located on the combination meter. When the S condition is normal, the S warning light illuminates
TIRE AND WHEEL TIRE PRESSURE WARNING SYSTEM. DTC C2121/21 No Signal from Transmitter ID1. DTC C2122/22 No Signal from Transmitter ID2
40 TIRE ND WHEEL TIRE PRESSURE WRNING SYSTEM DTC C2121/21 No Signal from Transmitter ID1 DTC C2122/22 No Signal from Transmitter ID2 DTC C2123/23 No Signal from Transmitter ID3 DTC C2124/24 No Signal from
DTC B1479/79: Flow Sensor Circuit
1 of 5 9/29/2015 11:17 PM 2010 Toyota RAV4 2.5L Eng Base DTC B1479/79: Flow Sensor Circuit DESCRIPTION The flow sensor is built into the compressor, and outputs a signal indicating the flow rate of the
GENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................................. 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION
GENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................... 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION FOR DIAGNOSIS.......
STEERING COLUMN SWITCHES
STEERING COLUMN SWITCHES 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Steering Column Switches Celica * PLEASE READ THIS FIRST * WARNING: Are equipped with a driver-side
A750F AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION SYSTEM
140 A750F AUTOMIC TRANSMISSION AUTOMIC TRANSMISSION SYSTEM P2740 P2742 P2743 Circuit Circuit Low Input Circuit High Input DESCRIPTION The No. 2 Automatic Transmission Fluid (F) temperature sensor is on
Taillight and Illumination
Taillight and Illumination L W C 5 L 3 F 5 TIL Relay 0 TIL 3 L W 8 TRLY 9 TIL IL 8 C (), 6(C) 8 ody ECU 50 J/ 8 IH (UZ FE) 0 LT Light Control SW 6 OFF Tail Head C Combination SW F 3 Front Parking Light
CAMRY STRIP LED DRL TOYOTA Part Number: Accessory Code: LDRS10. PIO / DIO Rev. A 02/26/13. Doc
Doc. 02.126.00 TOYOTA CAMRY PIO / DIO Rev. A 2013-02/26/13 STRIP LED DRL Part Number: 00016-32280 Accessory Code: LDRS10 Conflicts - Only works on Camry SE Kit Contents Item # Quantity Reqd. Description
EQUIPMENT - MAIN BODY 7-1 SECTION 7 EQUIPMENT CONTENTS
EQUIPMENT - MAIN BODY 7-1 SECTION 7 EQUIPMENT CONTENTS Engine Immobiliser System...7-1 Exterior Lights...7-2 Combination Meter...7-2 Smart Wiring System (SWS)...7-3 General Information...7-3 Functions
FUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
Body Electrical System
Body Electrical System GENERAL....BE -2 MULTI FUNCTION SWITCH...BE -8 HORN...BE -11 FUSES AND RELAYS...BE -12 INDICATORS AND GAUGES...BE -19 LIGHTING SYSTEM...BE -24 DAYTIME RUNNING LIGHTS...BE -30 BE-2
2UZ-FE ENGINE CONTROL SYSTEM SFI SYSTEM
160 2UZ-FE EINE CONTROL SYSTEM SFI SYSTEM DTC P0171 System Too Lean (Bank 1) DTC P0172 System Too Rich (Bank 1) DTC P0174 System Too Lean (Bank 2) DTC P0175 System Too Rich (Bank 2) DCRIPTION The fuel
TOYOTA HIGHLANDER FOG LIGHTS Preparation Part Number: PT , BLACK Part Number: PT , ALUMINIZED
Preparation Part Number: PT413-42191, BLACK Part Number: PT413-42190, ALUMINIZED Kit Contents Item # Quantity Reqd. Description 1 1 RH Fog Light 2 1 LH Fog Light Hardware Bag Contents Item # Quantity Reqd.
https://w05.dealerconnect.chrysler.com/service/mds2002/common/jsp/xml.jsp?xmlurl=... P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW
Page 1 of 10 P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW Page 2 of 10 For a complete wiring diagram Refer to the Wiring Information. Page 3 of 10 When Monitored: While the engine is running. Set Condition:
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION Self-diagnosis. Self-diagnosis BR-44 FUNCTION SELF-DIAGNOSIS PROCEDURE ABS
Self-diagnosis ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION Self-diagnosis FUNCTION NABR0095 NABR0095S01 When a problem occurs in the, the warning lamp on the instrument panel comes on. To start the self-diagnostic
Conflicts - Fog Lights
TOYOTA CAMRY 2013 - BLACKOUT LED DRL Part Number: 00016-32270 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver Box
ECM POWER SOURCE CIRCUIT
050 SFI SYSTEM (UZFE) 059UU0 ECM POWER SOURCE CIRCUIT CIRCUIT DESCRIPTION When the ignition switch is turned ON, battery positive voltage is applied to terminal IGSW of the ECM and the EFI relay (Marking: