TECHNICAL INFORMATION BULLETIN
|
|
- Bridget Nelson
- 5 years ago
- Views:
Transcription
1 TECHNICAL INFORMATION BULLETIN Reference: TIB 912 June 29, 2009 TITLE: Availability of Air Conditioning System Update Kit APPLICABLE PRODUCTS: This notice affects certain CAT Telehandlers manufactured by JLG Industries, Inc. The affected serial number range is as follows: Model TL642 TL943 TL1055 TL1255 Affected Serial Number Range TBK00100 to TBK01120 TBL00100 to TBL01517 TBM00100 to TBM TBN00100 to TBN00652 DESCRIPTION: An air conditioning update kit is now available for field installation on the referenced TL Series Telehandlers originally equipped with air conditioning. The air conditioning system has recently been redesigned to improve airflow and overall cooling capability. When installed in accordance with the enclosed instructions, this kit will update the internal ductwork of the original system to the current configuration. PARTS NEEDED: The parts needed for this update are as follows: Model Qty. Description Part Number TL642, TL943, TL1055, and TL Air Conditioning Update Kit Enclosure: Air Conditioning Update Kit Installation Instructions
2 Air Conditioning Update Kit Installation (Reference: TIB 912) Parts Required: Air Conditioning Update Kit # , Qty. 1 IMPORTANT: Use all applicable safety precautions while working on machine. Procedure 1. Prepare machine for servicing. Park the machine on a firm, level surface with boom lowered and fully retracted. Place travel select lever in the (N) NEUTRAL position and engage the parking brake. Shut engine OFF and chock a wheel. 2. Disconnect positive battery cable. Remove steering wheel from column. 3. Remove screws from center instrument panel, right side dash panel, and left side dash panel. Remove knob from auxiliary control lever. Remove key switch, tilt speed control, and fan from dash. Disconnect flex hoses from vents. 7. Remove temperature control from A/C control and drop through hole in right hand console. Remove knob from frame tilt lever, then remove cover panel. Remove front console first; plenum second; and finally rear console. Front console will be re-used, rear will not. 8. Remove all flexible vent hoses and discard. On TL642 and TL943 Models, remove and discard plenum. 4. Remove two bolts on right side of dash; two bolts and plate from the middle of the dash; and one bolt from the lower left corner of the dash. (It will not be necessary to disconnect any wiring from instrument panels. Panels can be angled and passed through holes in dash). 5. Remove dash panel from unit. This part will not be re-used. 6. Remove vent from front panel of seat riser. Remove four nuts holding seat and remove seat. Remove two clamps from rear of seat riser holding rear window washer hose and wiring. Remove four bolts and riser from cab. Seat will be re-used, riser will not. 9. Weld two 3/8-16NC nuts on rear cab tube into the locations specified in Figure 1 (on page 5). Take necessary precautions to prevent weld spatter damage to glass and interior surfaces of cab. DO NOT DRILL TUBE. Page 1 of 6
3 13. On a TL10 and TL12, route the decompression valve hoses behind a/c unit on floor of cab. Lower rear corner of seat riser is cut out to clear hoses. 10. Remove blower unit mounting bolts to access the mounting screws on bottom of three vent outlet. Remove thermostat switch from vent outlet cover. 11. Remove the three vent outlet covers from blower unit. Replace with four vent outlet cover. Reposition and install thermostat switch to upper rear corner of outlet cover. Seal cover with sealant tape. Short 2.5 outlet goes toward front of cab. 14. Install seat riser vent using four #6x1/2 self tapping screws. Install a/c decal in upper left corner. 15. Install seat riser. Route 48 hose and the 72 hose through oblong hole in side of seat riser. Route the 21 hose through slot in side of seat riser. 12. Install the four new vent hoses as shown below. Secure hoses with hose clamps: 2.5 x 15 to front vent 3 x 48 to 2 nd vent 3 x 72 to 3 rd vent 2.5 x 21 to rear vent After installing vent hoses, install blower unit mounting bolts. 16. Install R.H. Console and A/C control panel. The 48 and 72 hose will lie under the console and be directed toward the dash. The rear (21 ) hose needs directed upwards between the seat riser and console. 17. Connect rear top duct vent tube to rear flexible duct coming from blower unit. Tighten hose clamp to secure. Attach Page 2 of 6
4 tube to existing riv-nuts in rear cab wall using two 1/4-20x3 bolts, two 1/4 lock washers, and two 1/4 flat washers. Rotator wheels 20. Install sealant tape around rectangular hole at top rear of seat riser as shown below. 18. Assemble upper vent housing to bracket using two 5/16-18 x7/8 long hex head bolts, four flat washers, and two 5/16 nylon lock nuts. Connect upper vent tube to vent housing. Bolt housing and bracket to cab using two 3/8-16x 5/8 hex head bolts, two 3/8 flat washers, and two 3/8 lock washers. 21. Attach suction vent to top of seat riser using four 1/4-20x 5/8 long bolts, four 1/4 flat washers, and four 1/4 lock washers. Attach to cab using riv-nut with a 1/4-20 x 1 bolt, 1/4 flat washer, and a 1/4 lock washer. Route washer line and wiring behind suction vent and attach clamps. 19. Install adjustable louvers in vent housing using two #6x1/2 self-tapping screws in each louver. Keep the rotator wheel to the right side as shown below. Page 3 of 6
5 22. Connect suction vent filter to top of tube using six #6 x 1/2 self-tapping screws. Notch in dash Arrow point 27. Connect one 2-1/2 x approx. 13 duct hose to each louver. Secure hose to louver with hose clamp. 23. Re-install seat. 24. Install louver into front seat riser panel. Connect front hose to louver, securing with 2-1/2 hose clamp. Attach front panel to seat riser. 25. Install rectangular louvers in top of dash panel. Fasten each with two #6x1/2 self-tapping screws. Rotator wheel should be toward center of dash. 28. Assemble Y connectors to adapters. 26. Install ducts to round louvers and install louvers into front of dash. Align arrow point on louver with notch in dash panel. Page 4 of 6
6 29. Connect 2-1/2 duct hoses to connector, securing with hose clamps. Perform for each side of dash. Mount tilt speed control plate to dash and drill out center hole for shaft of controller. 30. Install dash panel in place, passing instrument/relay panel out through the opening in the dash panel. DO NOT bolt dash to cab at this time. 31. Connect hoses from A/C unit to Y connectors. Route longest 3 diameter hose to left side under steering column. Slide onto Y-connector and secure with hose clamp. Shorter 3 diameter hose will connect to right side Y-connector. 32. Mount cab fan to left side dash and connect wiring. Install key switch and tilt speed control. Re-install and tighten bolts that hold dash in place. Re-install screws that hold instrument panel and right hand panel to dash. 33. Re-install steering wheel. 34. Re-connect battery and prepare machine for operation. 35. Start engine. Switch A/C to ON position and check all vents for proper air flow. Page 5 of 6
7 Figure 1 Location of Weld Nuts on Rear Cab Tube Page 6 of 6
FACTORY AIR CONVERSION HEAT/ COOL/ DEFROST CHEVROLET CHEVELLE
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle FACTORY AIR CONVERSION HEAT/ COOL/ DEFROST 1970-72 CHEVROLET CHEVELLE CONTROL & OPERATING INSTRUCTIONS The controls on your
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD FAIRLANE & CROWN VICTORIA
PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1955-56 FORD FAIRLANE & CROWN VICTORIA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect Fit system, offer complete comfort capabilities in virtually
More informationSERVICE LETTER BEFORE. Reference: CAT April 5, 2011
BEFORE SERVICE LETTER Reference: CAT 1005 April 5, 2011 PRODUCT SUPPORT PROGRAM FOR UPDATING THE CURRENT PARKING BRAKE INSTALLATION ON CERTAIN CAT BRANDED TELEHANDLERS. ATTENTION: This program must be
More information& 76 CHEVROLET NOVA HEATER ONLY
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic hi l PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1969-74 & 76 CHEVROLET NOVA HEATER ONLY CONTROL & OPERATING INSTRUCTIONS The controls on
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST MUSTANG
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969-70 MUSTANG CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationCHEVROLET CORVETTE
Suggested Installation Instructions for: 658-133 and 658-134 1968-1976 Air Conditioning Retro-Fit System 1968-76 CHEVROLET CORVETTE CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect Fit
More informationParts & Service Information K810054C PRODUCT IMPROVEMENT
Parts & Service Information K810054C Disclaimer: This bulletin release is for informational purposes only and is not factory authorization for warranty repairs or warranty claim submission. PRODUCT IMPROVEMENT
More informationASSEMBLY MANUAL VALVE AND PLUMBING KIT INSTRUCTIONS NEW HOLLAND TRACTORS WITH TANDEM GEAR PUMP HYDRAULIC SYSTEM
ASSEMBLY MANUAL 715809002 BUNDLE 2-6437 Keep With Operator's Manual VALVE AND PLUMBING KIT INSTRUCTIONS NEW HOLLAND TRACTORS WITH TANDEM GEAR PUMP HYDRAULIC SYSTEM MODEL 2WD 4WD LESS CAB WITH CAB 5640,
More informationHEAT/ COOL/ DEFROST CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT FACTORY AIR CONVERSION HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1969 CHEVROLET CAMARO/ FIREBIRD NOTE: INSTRUCTIONS DEPICT CAMARO CONTROL & OPERATING
More informationPRODUCT: Install Instructions, MV-1 C/O Std, With Aux Fan RELEASE DATE: 2/28/14 REVISION DATE: 9/30/2014 PART NUMBER: Rev C
Parts List (1) 01 000 027 Switch, 4 Position Blower (1) 04 000 007 Hose, 1/2 ID Drain, 6 (1) 01 000 087 Harn, Resistor (1) 04 000 078 Tube, Convo 1/2 x 24 (2) 01 000 136 Relay, 40 Amp (1) 04 000 015 Hose,
More informationBlower Specifications
Lab These charts are arranged by increasing CFM. All lab blowers are 0Hz. See the preceding Four Steps To Blower Selection. 0 to CFM to / inch Static Pressure SIZE CODES -000/00 / () 0-00 / /0-0 () 0-000
More informationInstruction Sheet Kit Number:
Instruction Sheet Kit Number: 7914400 POWERED DECK LIFT KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand and follow all safety practices
More informationT2 Terminal Tractor Service Bulletin
T2 Terminal Tractor Service Bulletin Subject: Updated HVAC Wiring Harness, T2's Terminal Tractors Product: Medium Terminal Tractor Bulletin # SB18TI0090 Date: Pages: 7-August-2018 Page 1 of 11 Units Affected:
More informationWOC-364 Installation Instructions Ranger XP Heater System
WOC-364 Installation Instructions Ranger 2011-12 XP Heater System Order of installation for a Complete Enclosure Always install the Heater System first if possible NOTE: If installing the Heater System
More information1. Disconnect the battery. This is important! This will prevent air bag deployment.
PARTS PACKING LIST Evaporator assembly Drain tube Plastic air plug Hardware package 11040 3601 W. Clarendon Phoenix, Arizona 85019 (602) 233-0090 800-648-4475 www.ackits.com 2003-4 Jeep Wrangler EVAPORATOR
More informationI Page 1 of 5
Page 1 of 5 MOUNTING LOCATION: Upper right side of radio cavity-es300 Right sideof radio cavity-sc430&es350 Right side of climate control-solara TOOLS REQUIRED: Hook tool / Pry tool 10mm driver/ Phillips
More informationRzr Heater System Part #
Rzr Heater System Part # 2878135 NOTE: This heater unit installs below the center of the dash. If you have a radio mount kit (Polaris Part # 2876897) you may need to cut the top front corner off the mount
More informationPart Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short Bracket PF3000 Pro
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part No. PF3000 PF 3000 Pro U-Bracket Short 2000105-2 1 PFadvantage Bracket PF3000 Pro 2000773 1 Cable Kit
More informationTCI FastGate Shifter Installation Instructions
151 INDUSTRIAL DRIVE ASHLAND, MISSISSIPPI 38603 http://www.tciauto.com TELEPHONE: 662-224-8972 FAX LINE: 662-224-8255 E-MAIL: tech@tciauto.com TCI 616541 FastGate Shifter Installation Instructions The
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More informationParts List & Mounting Instructions Kubota F2260, F2560, F3060
JODALE PERRY Parts List & Mounting Instructions Kubota F2260, F2560, F3060 JDP BUILT FOR LIFE BRACKETS, SHIELDS, ETC.: Qty Description 1 Front bracket 6 Front bracket spacers 1 Fuel spout (w/cap) 1 4 x
More informationRESPA -CF/CFX Installation Kit for Komatsu D475A-5E0
Sy-Klone part number: REV3K13 Installation Time: 7 to 8 hours Purpose: RESPA systems preclean and filter air through integrated Gideon power precleaning technology. Filtration is provided by a MERV 16
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST MODEL BRACKET PACKAGE TO MOUNT O-MEGA STEPS/GRIP STEPS VEHICLE APPLICATION: 2001 AND NEWER FORD VANS
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL 570124 BRACKET PACKAGE TO MOUNT O-MEGA STEPS/GRIP STEPS VEHICLE APPLICATION: 2001 AND NEWER FORD VANS READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE
More informationZ-Gate Universal Shifter
Installation Instructions Z-Gate Universal Shifter Fits: GM, Ford, Lincoln and Chrysler Transmissions See Application Guide for Specific Applications Part #80681 Rev 06/01/2018 WORK SAFELY! For maximum
More informationMain Fire Pump Engagement. Shifting Into Pump 2006 / 2007 KME
Main Fire Pump Engagement Shifting Into Pump 2006 / 2007 KME 1 Battery Switch Ensure battery switch is turned on to BOTH. 2 Ensure Maxi (Parking) Brake Set Maxi (Parking) Brake must be set or the Pump
More informationJODALE PERRY. Parts List & Mounting Instructions. Jacobsen HR9016 JDP BUILT FOR LIFE
JODALE PERRY Parts List & Mounting Instructions Jacobsen HR9016 JDP BUILT FOR LIFE Jacobsen HR9016 Mounting Instructions Standard Parts 1 - LH Rear Mounting Bracket 1 - RH Rear Mounting Bracket 1 - Front
More informationINSTALLATION & OWNER S MANUAL
INDUSTRIES, LLC. INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS KUBOTA GRAND L 40 SERIES HARD SIDED CAB ENCLOSURE (p/n 1KGL4AS) This Curtis Cab is designed and manufactured for use only as
More informationTHE SERIES-E POWR Slider
C.R. LAURENCE CO., INC. PATENT NO. 4,920,698 THE SERIES-E POWR Slider MODEL: EPC814S 2014+ CHEVY/GMC SILVERADO/SIERRA 1500 NAGS: DY90122PK5 ELECTRIC SLIDING REAR WINDOW 2014 + CHEVY/GMC SILVERADO/SIERRA
More informationWARNING. PN Rev Crary Big Top Instruction Sheet Big Top No , 53408, & 54289
ASSEMBLY INSTRUCTIONS CASE IH 50, 60/0, 010/010 & 120/120/9120 SERIES NEW HOLLAND CR STD SERIES COMBINES (LARGE) BIG TOP 5424, 5340, 542 & 5429 The Crary Big Top Large Extension fits right on top of the
More informationBulletin 1494V Variable Depth, Flange Operated Disconnect Switch Kits for 400 and 600 Amperes (Series A) Switches
Bulletin 494V Variable Depth, Flange Operated Disconnect Switch Kits for and Amperes (Series A) Switches ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing.
More informationINSTRUCTION, BMR AUXILIARY CONTROL
LIFT CORPORATION Sht. 1 of 10 DSG# M-16-05 Rev. A Date: 01/16/17 INSTRUCTION, BMR AUXILIARY CONTROL GRAVITY DOWN CONTROL KIT, P/N 297080-11 POWER DOWN CONTROL KIT, P/N 297080-12 ELECTRICAL CONTROL TEE
More informationTT /13b INSTALLATION INSTRUCTIONS. Introduction
TT-5 /b INSTALLATION INSTRUCTIONS Original Issue Date: 5/09 Model: 0RESA, 0REYG, 0RES, 0RYG, and RGEN0 Market: Residential/Commercial Subject: Oil Makeup Kits GM654 -KP, GM654-KP, and GM8987-S Introduction
More informationINSTALLATION INSTRUCTIONS ISLAND LINER INSERT
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS ISLAND LINER INSERT Read All Instructions Thoroughly Before Beginning Installation WARNING
More informationProcedure. These guidelines can be found in the "Accessory Installation Practices" document.
Toyota Tundra 207 LED Illumination Package Part Number: 0006-00069 (Interior and Exterior) Accessory Code: LL000 Conf licts V ehicles with Option Code BZ Color Applicability/Trim Level Kit Content 4 Puddle
More informationHAND THROTTLE KIT For Workman 3000 Series
FORM NO. 7 6 MODEL NO. 0746 INSTALLATION INSTRUCTIONS HAND THROTTLE KIT For Workman 000 Series. Position vehicle on a clean, level surface, stop engine, engage parking brake and remove key from ignition
More informationCONTROL SYSTEM FOR THE PHYSICALLY DISABLED
INSTALLATION Push/Rock HAND CONTROL SYSTEM FOR THE PHYSICALLY DISABLED With Howell Ventures Ltd Sure Grip Hand Control Systems and Accessories are warranted against manufacturing or material defects for
More informationINSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST. For Use with Bard C**H Series 2 & 2½ Ton 2-Stage Wall Mount Heat Pumps
INSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST MODEL CHCRV-3 For Use with Bard C**H Series 2 & 2½ Ton 2-Stage Wall Mount Heat Pumps NOTE: CHCRV-3 Models must be installed with TCURB
More informationTL INSTALLATION MANUAL FOR TELMA AF50-55 ON CHEVROLET G4500 CUTAWAY 6.0L GASOLINE and 6.6L DIESEL ENGINE
INSTALLATION MANUAL FOR TELMA AF50-55 ON CHEVROLET G4500 CUTAWAY 6.0L GASOLINE and 6.6L DIESEL ENGINE 1apr17jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 1.3 Fuel Tank 2 Telma
More informationCopyright 2017 ORIFLOW LLC. Operating Instructions for Cobra and Lynx Duct Leakage Testers
Operating Instructions for Cobra and Lynx Duct Leakage Testers Table of Contents Introduction Introduction.. 2 Safety Precautions Safety Precautions READ FIRST!... 2 Prior to Testing Are You Using the
More informationTL INSTALLATION MANUAL FOR TELMA AC50-55 ON FORD E-350/450 CUTAWAY WITH TELMA CONTROL MODULE
INSTALLATION MANUAL FOR TELMA AC50-55 ON FORD E-350/450 CUTAWAY WITH TELMA CONTROL MODULE 17feb12jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 2 Telma Installation 2.1 Installation
More information\\,, I l- m.. -=_!:~ /20/93 G W-W/O PS SERIES FORD V8-351, :-- REV B FISHER ENGINEERING, ROCKLAD, ME HPS i '&.
SERIES FORD V8-35,400 977-979 G W-W/O PS PECULIAR HYDRAULICS BELT DRIVE, SLC UNDERHOOD VALVE HPS4504 REV B _\ _C\./,, \\,, \\,,,, ~ ~I :- e l,. i '&. I l- ~~ :-- e l m.. -=_!:~ ~.æ=iiii å FISHER ENGINEERING,
More informationPARTS LIST FOR VIPER VIPER
P-336 P-336 PARTS LIST FOR P-336-A P-336-A ILLUSTRATION OF SUB-ASSEMBLIES 6 3 1 5 2 4 P-336-A.1 P-336-A.1 For Codes: 10597 to 10635 Do Not use this Parts List for a machine if its code number is not listed.
More informationTABLE OF CONTENTS INTRODUCTION.. 3. A/C Ducting Installation. Power Kit Installation (Batteries)...5 OPERATION MANUAL 7-8 TOOLS LIST..
585457 1 TABLE OF CONTENTS SECTION PAGE INTRODUCTION.. 3 INSTALLATION PROCEDURES Air Conditioner Location...4 Air Conditioner Mounting 4 A/C Ducting Installation...5 Power Kit Installation (Batteries)...5
More informationBulletin 1494C Cable Operated Disconnect Switch Kit (600A) Installation Instructions (Cat 1494C- _ Series 2 : 600A)
Bulletin 494C Cable Operated Disconnect Switch Kit (600A) Installation Instructions (Cat 494C- _ Series : 600A) ATTENTION: To prevent electrical shock, disconnect from power source before installing or
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationLED Fog Light. Conflicts Note: 1832, 1852, 1856, 1872, General Applicability Fits Models
LED Fog Light Year & Model Part Number 2017 Corolla TCO-817 Conflicts Note: 1832, 1852, 1856, 1872, 1874 General Applicability Fits Models 1863 1866 1864 1865 Additional Items Required For Installation
More information1000 Park Drive Lawrence, PA Fax
Copyright 2008. Black Box Corporation. All rights reserved. 1000 Park Drive Lawrence, PA 15055-1018 724-746-5500 Fax 724-746-0746 JANUARY 2008 RM810A-R2 RM825A-R2 RM840A-R2 RM855A-R2 RM812A-R2 RM825A-3F-R2
More informationRef Qty Part Description Part Number -1- Kit ( ) Contents:
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationINSTRUCTION, BMR STREET-SIDE CONTROL
LIFT CORPORATION Sht. 1 of 13 DSG# M-16-04 Rev. A Date: 01/13/17 INSTRUCTION, BMR STREET-SIDE CONTROL GRAVITY DOWN CONTROL KIT, P/N 297080-01 POWER DOWN CONTROL KIT, P/N 297080-02 ELECTRICAL CONTROL TEE
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS MASSEY FERGUSON TGX SERIES SOFT SIDED CAB ENCLOSURE (p/n MFTGXSS) This Curtis Cab is designed and manufactured for use only as reasonable weather
More informationInstallation Instructions StarShifter
Installation Instructions StarShifter Part Number 80675 2000 by B&M Racing & Performance Products LLC The B&M StarShifter can be used in vehicles equipped with most popular three speed automatic transmissions.
More informationPRO RATCHET UNIVERSAL SHIFTER
Installation Instructions PRO RATCHET UNIVERSAL SHIFTER Fits: GM, Ford and Chryslers w/automatic Transmission See Application Guide for Specific Vehicles Catalog # 80842 WORK SAFELY! For maximum safety,
More informationTL INSTALLATION MANUAL FOR TELMA AF50-55 ON FORD E-350/450 CUTAWAY with rotary foot switch design 2 including MY2016 changes
INSTALLATION MANUAL FOR TELMA AF50-55 ON FORD E-350/450 CUTAWAY with rotary foot switch design 2 including MY2016 changes 10nov16jh TABLE OF CONTENTS 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust
More informationBefore disconnecting battery Ground (GND) strap obtain security code for radio with antitheft
Page 1 of 14 Volkswagen > New Beetle > 1998-2005 Body Interior 70 - Interior trim Instrument panel, removing and installing WARNING! Disconnect battery Ground (GND) strap before working on electrical system,
More informationSerial Number Range TBF00100 & After TBG00100 & After TBH00100 & After TBP00100 & After TBJ00100 & After
SPECIAL INSTRUCTION Reference: SI E 1001 June 15, 2010 Attention: This notice is being issued to advise you of new information for certain Caterpillar ( CAT ) Telehandlers that were manufactured by JLG
More informationINSTALLATION INSTRUCTIONS 97 FORD EXPEDITION
INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before
More informationINSTALLATION INSTRUCTIONS WALL MOUNT RANGE HOOD WITH M600 OR M1200 BLOWER
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK C U L R Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT RANGE HOOD
More informationFAX
INSTALLATION INSTRUCTIONS 6299 Air Suspension Kit (pat. pending) 2009+ Dodge 1500 Pickup with Rear Coil Springs Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationCSA CERTIFIED Conforms to UL 507
Installation tion Instructions Please read and save these instructions! TURBO/MAXX12 Volt All Weather RV Ventilator Fans P/N 00-965001 Deluxe Model 1200T WITH THERMOSTAT P/N 00-965007 Standard Model 3550
More informationINSTALLATION INSTRUCTIONS WALL MOUNT RANGE HOOD WITH M600 OR M1200 BLOWER
WARNING - TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK C U L R Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT RANGE HOOD
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE GATOR HPX and/or XUV HARD SIDED CAB ENCLOSURE (p/n: 1GTR44AS) SOFT SIDED CAB ENCLOSURE (p/n: 1GTR44SS) 111 HIGGINS STREET, WORCESTER,
More informationP/N Rev 01 04/14-1- NOTE: If you are ordering hinges for your rear doors, order and/or
REAR CANVAS DOOR KIT 900 XP RANGER CREW P/N 2879899 Application RANGER 900 XP CREW Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain
More informationChrysler 727, 904, 518 Floor Mount Automatic Transmission Shifter Installation Instructions
Chrysler 727, 904, 518 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Button
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationLANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS
LANCER EVOLUTION (2008 ) MUD FLAP MZ531356EX (Black with aluminum plate) MZ531357EX (Black standard) INSTALLATION AND HANDLING INSTRUCTIONS Black with aluminum plate -MZ531356EX Black standard -MZ531357EX
More informationEXTERIOR BASE MOUNT INSTALLATION (FIG. 2)
EXTERIOR BASE MOUNT INSTALLATION (FIG. 2) IMPORTANT! The installer is responsible for determining the most appropriate fastener to secure the base mount to the roof and weatherproofing all holes with sealant.
More informationAll bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code below.
Page 1 of 12 Last Modified: 9-21-2007 1.6 A Service Category: Vehicle Interior Section: Interior Panels/Trim Model Year: 2008 Model: Tundra Doc ID: RM000002VHU003X Title: INSTRUMENT PANEL: INSTRUMENT PANEL
More informationPavement Services, Inc.
MG68 Parts Manual Pavement Services, Inc. Page 30 29 30 29 25 25 24 30 4 26 29 4 25 26 4 Page 2 The Decal Kit for the Model MG68 Maintainer is Item Part # Description 056859 DECAL, ANTI-FREEZE (BLACK)
More informationTL INSTALLATION MANUAL FOR TELMA AF50-55 ON CHEVROLET G4500 CUTAWAY 6.0L GASOLINE WITH ROTARY FOOT SWITCH
INSTALLATION MANUAL FOR TELMA AF50-55 ON CHEVROLET G4500 CUTAWAY 6.0L GASOLINE WITH ROTARY FOOT SWITCH 6nov15jh 1 Preparation of the Chassis 1.1 Driveline 1.2 Exhaust 1.3 Fuel Tank 2 Telma Installation
More informationNOTE: The process described below is for removing the seat FRAME. The seat PLATFORM is welded to the bottom of the cab and cannot be removed.
Removing the seat frame on an Advance Design pickup NOTE: The process described below is for removing the seat FRAME. The seat PLATFORM is welded to the bottom of the cab and cannot be removed. STEP 1..
More informationRESPA -CF2 Installation Kit for John Deere K and K-II Wheel Loaders
Technical Support www.sy-klone.com support@sy-klone.com (904) 448-6563 ext. 1310 Sy-Klone part number: RCF2702 Fits K and K-II Series: 444, 524, 544, 624, 644, 724, 744, 824, 844, 944 Installation Time:
More informationINSTALLATION INSTRUCTIONS K SERIES LINER INSERT
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS K SERIES LINER INSERT Read All Instructions Thoroughly Before Beginning Installation WARNING
More informationONLY AFTER ALL MEASUREMENTS HAVE BEEN TAKEN. Remove any components in the chassis that may interfere with the retarder and/or mounting hardware.
Tools Needed Transmission jack Hand held calculator Mechanics hand tools Torque wrench (up to 250 lb.-ft) ½ heavy duty drill or frame drill Tape measure Straight edge Electronic Angle meter (Spicer Anglemaster
More informationTABLE OF CONTENTS INTRODUCTION 3. INSTALLATION PROCEDURES Air Conditioner Location 4. A/C Ducting Installation 5
585474 1 TABLE OF CONTENTS SECTION PAGE INTRODUCTION 3 INSTALLATION PROCEDURES Air Conditioner Location 4 Air Conditioner Mounting 4 A/C Ducting Installation 5 Power Kit Installation (Batteries). 5 Separator...
More informationSubject: Chassis and Cab Power Distribution Center Nylon Washers Product: Medium Terminal Tractor. Date: 24-JUN-2016
Page 1 of 11 Units Affected: All Kalmar Ottawa T2 model terminal tractors built prior to October 13, 2015. Possible Situation: The fasteners for the cab and chassis power distribution boards may abrade
More informationPiston Cooling Nozzle, Replacement
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces Service Bulletin 221-49, Piston Cooling, dated (1.2007), publication no. PV776-20177472. DService Bulletin Trucks Date Group
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: R42H (2011) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description Service
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92/E93 335i/xi with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0920 APPLICATION 2007-10 E92/E93 335i/xi with stock oil cooler Congratulations for being selective enough to use a Dinan Engineering Oil Cooler
More informationCORVETTE. w/ AC CONTROL PANEL CONVERSION KIT an ISO 9001: 2008 Registered Company
an ISO 00: 00 Registered Company - CORVETTE w/ AC PANEL CONVERSION KIT AIR COND PULL 0 AIR PULL-FAN DEFROSTER PULL VOL TONE TUNING 0 0 00 000 REV B //, INST - VETTE w/ AC CNTRL PNL PG OF Table of Contents
More informationINSTALL MANUAL. FOR ON LINE ORDERING- E Commerce Visit Our Website
INSTALL MANUAL FOR ON LINE ORDERING- E Commerce Visit Our Website WWW.PRESSUREGUARD.COM Contact Information Technical Support: Chris@pressureguard.com Sales Support: Sales@pressureguard.com By Phone: 615-227-6024
More information1969 CAMARO VCZ-A
969 CAMARO w/o FACTORY AIR 55070-VCZ-A 8865 GOLL ST. - SAN ANTONIO, TX. - 78266 ph.20-654-77 - fax 20-654-33 905070-VCZ-A /22/05, 69 CAMARO w/o FAC. AIR INSTRUCTIONS PG OF 20 969 CAMARO w/o FACTORY AIR
More information/ i I ~~. $.. -- ~ :: ( : \~ l-i ~ I. / n i ~ * Jij_ / 62Qo 5/29/91 ~ (. \ \ \ \ ~ h: ~ G W/O AC ~~ ~ \ \ \ \ / _J PECULIAR HYDRAULICS
; c. SERIES FORD V8-460 G W/O AC 1983-1987 PECULIAR HYDRAULICS. BELT DRIVE, SLC UNDERHOOD VALVE HPS4551 REV C / / _J- - \ \ \ \ \ \ \ \ \ /) ~ ii / io~. \i / i I / n i \~ l-i ~ I Jij_ / i I / ~ :: ~ (.
More informationInstallation Instructions
Installation Instructions www.bestop.com - We re here to help! Visit our web site and click on Ask a Question INSTALLATION TIME SKILL LEVEL Automatic Retracting Running Board Vehicle Application Chevy
More informationHAND CONTROL SYSTEM FOR THE PHYSICALLY DISABLED
INSTALLATION Push/Twist HAND CONTROL SYSTEM FOR THE PHYSICALLY DISABLED with Howell Ventures Ltd Sure Grip Hand Control Systems and Accessories are warranted against manufacturing or material defects for
More informationINSTALLATION INSTRUCTIONS CWEH6-K WALL MOUNT HOOD
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS CWEH6-K WALL MOUNT HOOD Read All Instructions Thoroughly Before Beginning Installation WARNING
More information~ Manufactured. '-ccz CR, ", MOUNTING INSTRUCTIONS. With Replacement Parts Listing For A OPTIONS
'-ccz CR, ", '..." 5 ' '.", ;,...,...'.,!e./i,.,.',.' ',', MOUNTING INSTRUCTIONS With Replacement Parts Listing For TORO 355-D/455-D A-47 ROPS CAB I- OPTIONS 4-3069 Heater Kit Option 4-307 Flashing Light
More informationC WD 2 WHEEL LOW KIT FOR DODGE RAM 4WD VEHICLES
C18056-4WD 2 WHEEL LOW KIT FOR 1994-2002 DODGE RAM 4WD VEHICLES Pacbrake s 4WD 2 Wheel Low Kit allows the vehicle operator to engage the transfer case into 4WD low range without engaging the front wheel
More informationNew Holland MC22, MC28, MC35
New Holland MC22, MC28, MC35 Parts List & Mounting Instructions Jodale Perry Printed: 2004/01 Standard Parts List Qty Description Photo 1 Front Cab Mount Bracket L&R Rear Cab Mount Brackets 1 Inner Foot
More informationOUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS)
80052 March 6, 1995 OUT FRONT ELECTRIC HYDRAULIC (W/E-47H) FOR STRAIGHT TRIPEDGE PLOWS (PULL AWAY MOUNTINGS) ITEM STOCK DESCRIPTION QTY. 51 15759 LIFT UNIT (E-47H) 1 52 817000 020 10" CYLINDER 2 53 15370
More informationINSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST. For Use with Bard 2 2-1/2 Ton Wall Mount T Series Heat Pumps
INSTALLATION INSTRUCTIONS COMMERCIAL ROOM VENTILATORS WITH EXHAUST MODELS CRVMWH-3 For Use with Bard 2 2-1/2 Ton Wall Mount T Series Heat Pumps Bard Manufacturing Company, Inc. Bryan, Ohio 43506 Since
More informationVALVE AND PLUMBING KIT 2408TL LOADER AGCO & MASSEY FERGUSON TRACTORS
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT 2408TL LOADER AGCO & MASSEY FERGUSON TRACTORS AGCO MASSEY FERGUSON CAB ROPS ST34A 1533 X ST41A 1540 N/A X TRACTOR AND VALVE KIT GENERAL
More informationInstallation Instructions Factory Style Bow Kit
Installation Instructions Factory Style Bow Kit Vehicle Application: Jeep Wrangler JK 2 Door 2007 Current Part Number: 55000 Compatible with original equipment soft tops, 54722 Supertop NX and 79142 Sailcloth
More informationLGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions
LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative connections
More informationInstallation Instructions
8/0A,A,A,A,AJ,AK,AW,AY00-00 Power Exhaust, Barometric Relief, and Conversion Package Accessories Installation Instructions Power Exhaust Part Numbers: CRPWREXH0A00, CRPWREXH0A00, CRPWREXH0A00, CRPWREXH0A00
More information2015+ F-150 Active Exhaust Kit Installation Instructions P/N: (1117-5E292LITE)
2015+ F-150 Active Exhaust Kit Installation Instructions P/N: 422104 (1117-5E292LITE) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015+ Ford F-150 Active Exhaust Kit Installation Instructions
More informationIDS ILLINOIS, LLC. 2000/2500 DEVICE & OPERATOR
IDS ILLINOIS, LLC. 2000/2500 DEVICE & OPERATOR INSTALLATION MANUAL 922 Geneva Street Shorewood, IL 60404 PH: 815/730-0050 FX: 815/730-0057 IDS ILLINOIS, LLC. Quick List Quick Reference for Installation
More informationInstall Instruc & Recommended Procedures
Install allation Instruc uctions & Recommended Procedures Unlike other radar detectors and aftermarket accessories, the K40 Calibre will not interfere with the vehicle's complex electronic systems. The
More informationP RO W ALL V ENTILATION H OODS INSTALLATION INSTRUCTIONS
P RO W ALL V ENTILATION H OODS INSTALLATION INSTRUCTIONS CONTACT INFORMATION Wolf Customer Service: 800-332-9513 Website: wolfappliance.com As you follow these instructions, you will notice WARNING and
More informationREPAIR INSTRUCTIONS - ON VEHICLE
2013 TRANSMISSION Automatic Transmission - 6T40 - Repair Instructions - On Vehicle - Orlando REPAIR INSTRUCTIONS - ON VEHICLE MANUAL SHIFT DETENT LEVER WITH SHAFT POSITION SWITCH ASSEMBLY REPLACEMENT Special
More information