TECHNICAL AND SERVICE BULLETIN
|
|
- Gwen Scarlett Stevens
- 5 years ago
- Views:
Transcription
1 SHEET 1 OF 9 TITLE: INSTALLATION INSTRUCTIONS FOR FAST CHARGE SYSTEM 1. EFFECTIVITY CHARLATTE T135 with POWER PAC CONTROLLERS 2. REASON TO INSTALL FAST CHARGE SYSTEM 3. DESCRIPTION FAST CHARGE AUXILLARY COMPONENTS INSTALLED IN VEHICLE 4. COMPLIANCE CHARLATTE T135 with POWER PAC CONTROLLERS 5. MANPOWER AS NECESSARY 6. TOOLING HANDTOOLS, DRILL WITH 5/32, 3/16, 3/8, AND 1/2 BITS 7. REFERENCE SEE ATTACHED PAGES 8. MATERIAL AVAILABILITY ALL INCLUDED IN THE RETROFIT KIT 9. ACCOMPLISHMENTS FOLLOW THE INSTRUCTIONS INCLUDED
2 SHEET 2 OF 9 SAFETY! 1. DRIVE THE T135 TO A PROPER MAINTENANCE AREA. SHUT DOWN THE UNIT AND SET THE PARKING BRAKE BEFORE MAINTENANCE IS PERFORMED. NOTICE BE SURE TO DISCONNECT THE BATTERY PLUGS LOCATED UNDER THE HOOD OF THE TRACTOR BEFORE PROCEEDING. CUTTING THE HOLE FOR BURTON BOX HOUSING 2. THE HOLE CAN NOW BE CUT AT THE BACK OF THE TRACTOR TO ACCOMMODATE THE NEW FAST CHARGE BURTON PLUG. THE HOLE NEEDS TO BE APPROX INCHES BY 1.75 INCHES. CUT THE HOLE AS SHOWN IN THE ATTACHED ENGINEERING DRAWING WITH AN AN OXY-ACETYLENE TORCH. THIS WILL MAKE SURE THE CABLES WILL RUN SMOOTHLY FROM THE BURTON RECEPTACLE TO THE BATTERY CONNECTOR. GRIND OFF THE EDGE OF THE CUT ALL THE WAY AROUND SO THAT THE HOLE IS SMOOTH. THIS WILL ALLOW YOU TO PASS THE SBX PLUG THROUGHT THE PANEL. 3. FIT THE PIECE OF SHEATHING AROUND THE INSIDE OF THE 3.75x1.75 HOLE TO COVER ITS EDGES.
3 SHEET 3 OF 9
4 SHEET 4 OF 9 BURTON BOX INSTALLATION 4. NOW INSTALLATION CAN BEGIN FOR THE YELLOW BURTON BOX (SUPPLIED IN RETROFIT KIT) THAT WILL HOUSE THE BURTON RECEPTACLE. TAKE THE EMPTY BOX IN HAND AND PLACE AS SHOWN BELOW, BEING CAREFUL TO MAKE THE SHIELD EDGE FLUSH WITH THE OUTSIDE OF THE REAR TRACTOR PLATE (MAKE SURE THERE IS AN EASY PATH FOR THE CABLES THROUGH THE NEWLY CUT HOLE). MARK THE FOUR (4) HOLE CENTERS WITH THE EMPTY BOX AND DRILL OUT THE HOLES WITH 3/8 DRILL. CONNECTING THE BURTON RECEPTACLE TO YELLOW BOX 5. PROVIDED IN THE KIT IS A SMALL HARNESS OF 4 COLORED WIRES. ON ONE END OF EACH WIRE IS A RING TERMINAL. ATTACH THESE WIRES VIA THE RING TERMINALS TO THE CORRECT TERMINALS ON THE BURTON RECEPTACLE (AEROVIROMENT WILL ASSIST WITH CORRECT WIRE PLACEMENT). 6. TIGHTEN DOWN THE TWO 2/0 CABLES ON THE BURTON RECEPTACLE IN THE ORIENTATION TO PASS THESE CABLES THROUGH THE REAR WALL OF THE TRUCK.
5 SHEET 5 OF 9 7. GET THE YELLOW BOX SUPPLIED IN RETROFIT KIT AND USING THE 4 SCREWS PROVIDED ATTACH THE BURTON RECEPTACLE WITH ATTACHED CABLING IN POSITION. SEE PICTURE BELOW. 8. RUN THE SBX PLUG AND ATTACHED BLACK CABLES AND FOUR (4) COLORED WIRES THROUGH THE NEWLY MADE 3.75x1.75 HOLE, LEAVING THEM LAYING ON THE MOTOR AND SET BOX OVER THE FOUR 3/8 DRILLED HOLES TO BOLT BOX DOWN WITH THE PROVIDED 5/16 1 BOLTS AND SPLIT WASHERS: CONNECTING THE RECEPTACLE TO BMID CONTROLLER 9. TAKE THE 4 #16 GAUGE WIRES AND PLUG THEM INTO THE 4-PIN FEMALE WEATHERPACK PLUG (PROVIDED IN THE KIT) IN THE ORDER AEROVIROMENT REQUIRES. CONNECT THIS PLUG TO THE 4-PIN MALE PLUG FROM THE BMID CONTROLLER (AEROVIROMENT TO SUPPLY).
6 SHEET 6 OF 9 REMOVAL OF OLD CHARGING SYSTEM 10. OPEN THE CONTROLLER PANEL BOX BY REMOVING BLACK PLASTIC COVER WITH SPECIAL TRIANGULAR KEY OR 11/32 SOCKET DISCONNECT THE BLUE CABLE (FROM THE CHARGING PLUG) FROM THE B- POST OF THE POWER PAK CONTROLLER. (SEE POINT 11 ABOVE) 12. DISCONNECT THE RED CABLE (FROM THE CHARGING PLUG) FROM THE CHARGING CONTACTOR + POST. (SEE POINT 12 ABOVE) 13. DISCONNECT THE BLACK/WHITE WIRE (FROM THE CHARGING SWITCH) FROM THE CHARGING CONTACTOR + POST. (SEE POINT 13 ABOVE) 14. DISCONNECT THE BLACK WIRE (FROM THE CHARGING SWITCH) FROM THE CHARGING CONTACTOR COIL TERMINAL. (SEE POINT 14 ABOVE)
7 SHEET 7 OF MOVE THE RED CABLE, FROM THE BATTERY SIDE (+ MARKED SIDE) OF THE CHARGING CONTACTOR, TO THE OTHER SIDE OF THE CONTACTOR. THEREFORE THERE ARE NOW TWO CABLES ON ONE SIDE OF THE CHARGING CONTACTOR (SEE POINT 15 BELOW) MOVE THE #001 MARKED WIRE FROM THE OUTSIDE TERMINAL OF THE MICRO SWITCH ON THE CHARGING CONTACTOR TO THE TERMINAL INSIDE IT. MOVE THE #119 MARKED WIRE FROM THE OUTSIDE TERMINAL ON THE SAME MICRO SWITCH TO THE TERMINAL JUST INSIDE IT. THESE WIRES ARE NOW ON THE NORMALLY CLOSED SIDE OF THE MICRO SWITCH. (SEE POINT 16 ABOVE).
8 SHEET 8 OF REMOVE THE FOUR (4) SCREWS FROM THE CHARGING PLUG LOCATED AT THE REAR OF THE TRACTOR. INSTALL THE FOUR (4) SHORTER SCREWS INCLUDED IN THE KIT TO PLUG THE HOLES. CHARGING PLUG AND HARDWARE 18. REMOVE THE TWO (2) SCREWS FROM THE INTERLOCK SWITCH LOCATED AT THE REAR OF THE TRACTOR. INSTALL THE TWO (2) SCREWS REMOVED BACK INTO THE HOLES TO PLUG THEM. INTERLOCK SWITCH AND HARDWARE 19. REMOVE THE CHARGING PLUG / WIRES AND CHARGING SWITCH / WIRES FROM THE TRUCK. 20. BLOCK THE HOLE UP THAT THE WIRES PASSED THROUGH TO PREVENT WATER GETTING INTO THE CONTROL PANEL. 21. CHECK ALL CONNECTIONS IN THE CONTROLLER BOX TO MAKE SURE TIGHT. 22. CONNECT THE CONTROLLER SBX PLUG TO THE SBX PLUG THAT GOES TO THE BURTON PLUG
9 SHEET 9 OF CLAMP CABLE (FROM THE SBX PLUG TO THE BURTON PLUG) TO REAR OF TRUCK USING THE CLAMP PROVIDED IN THE KIT. THIS SHOULD BE CLAMPED TO ALLOW BURTON PLUG TO BE PLUGGED INTO BURTON RECEPTACLE AND WHEN UNPLUGGED NOT HIT THE GROUND. THE CLAMP SHOULD ALSO ALLOW THE TRUCK S REAR LID TO SHUT CORRECTLY. 24. CONNECT THE BATTERY SBX PLUG TO THE SBX PLUG ATTACHED TO THE BURTON RECEPTACLE 25. FINALLY CONNECT THE BURTON PLUG TO RECEPTACLE. WARNING NOTE :- POWER IS NOW GOING TO THE CONTROL PANEL.
Installation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationOCF/LOV Heated Shortening Kit
OCF/LOV Heated Shortening Kit This kit adds a heated JIB platform and heat tape to provided and existing flex lines to accommodate the use of semi-solid shortening The changes are broadly explained below.
More informationRANGER MIDSIZE WINCH KIT
RANGER MIDSIZE WINCH KIT P/N 2881669 APPLICATION ALL MY RANGER 400; MY11 AND NEWER RANGER 500 EXCEPT CREW BEFORE YOU BEGIN Read these instructions thoroughly and make sure all parts and tools are accounted
More informationT u n i n g. Professional Install
DDM INSTALL GUIDE H1 HID Low Beams (35W or 55W) ddm T u n i n g TOOLS NEEDED: - Standard or metric socket set. Depending on the vehicle. - A drill and either a uni-bit or a 7/8 drill bit. - A Dremel with
More informationigen2500 and ipro2500 IGNITION COIL RETROFIT GUIDE
igen2500 and ipro2500 IGNITION COIL RETROFIT GUIDE This comprehensive retrofit guide is for replacing the ignition coil on Westinghouse s igen2500 and ipro2500 inverter generators. The purpose of this
More informationCut zip ties and remove 2 plastic wiring harness brackets.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. Included parts: 1 - New Bosch Cp3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/
More informationINSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax)
INSTALLATION MANUAL August 7 th 2018 43 /48 /50 2011 and Older Timpte STD/Split 36 Style Hopper Trailers with Roller Bearing Doors Kit #101533 for 96w & Kit #101534 for 102w Thunderstone Manufacturing
More informationA B C D E F. Tools Required (supplied by others)
Page 1 of 17 Parts List Below Deck Automatic Retractable Security Cover Kit (1) Tube End Bearing Plate (A) (1) Rope Reel and Cover Drum Motor Assembly (B) (1) Cover Drum (1) Pulley Support Channel (2)
More informationWoda-Sci System Installation Parts Set
Installation Manual Woda-Sci System Installation Parts Set 5/32 x 3 ½ Drill Bit - 5 Connector Body - 7 3/8 Locking Nut - 8 3/16 x 1 ¼ Concrete Anchors- 4 Mounting Screws - 3 Stainless Steel Hanger - 9
More information850 TETHER SWITCH KIT
850 TETHER SWITCH KIT P/N 2883823 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationCut zip ties and remove 2 plastic wiring harness brackets.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationContents. TCS/ Driver Mod Installation Manual
Contents Introduction... 1 TCS Packing List... 3 Tools Needed for Installation... 4 How to Properly Solder... 5 Soldering Standard Butt Connection... 5 Soldering T Connection... 6 How to Properly Crimp...
More informationGW-CRUISE Cruise Control Vanagon [84-91]
Driving without cruise control on a long trip can be tiring. Update your vehicle with some modern convenience with this easy to install cruise control kit. Tools Needed Phillips screwdriver #2 Electric
More informationRoadRelay 4. Installation Guide
RoadRelay 4 Installation Guide RoadRelay 4 Installation Guide Bulletin No. 3401767 Revision B Copyright 2002, Cummins Inc. All rights reserved. Cummins Inc. shall not be liable for technical or editorial
More informationRetrofit Steering Column Installation Instructions
Retrofit Steering Column Installation Instructions for 1965-66 Mustangs www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 PH: (517) 424-0577 FAX: (517) 424-7293 Revised 3/22/2010 Instruction #: 8000000011
More informationTable of Contents. 4 Getting Started 4 About the Juice 5 Safety Terms 5 Product Registration 6 Important Notes 7 Truck Orientation
Table of Contents 4 Getting Started 4 About the Juice 5 Safety Terms 5 Product Registration 6 Important Notes 7 Truck Orientation 8 Juice Installation 1999-2003 (7.3L) 8 Supplied Items & Required Tools
More informationJEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4
JEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4 PARTS LIST QTY DESCRIPTION 1 Drivers Side Slider Assembly 1 Passenger Side Slider Assembly 1 Wiring Harness and Fuse 1 Double Sided Sticky Squares and Alcohol
More informationPowerFlo 20 Parts List/Assembly Instructions/Users Guide ***PLEASE READ ALL INSTRUCTIONS CAREFULLY AND THOROUGHLY***
PowerFlo 20 Parts List/Assembly Instructions/Users Guide ***PLEASE READ ALL INSTRUCTIONS CAREFULLY AND THOROUGHLY*** Owners Manual (Please check to make sure to locate all parts before assembly.) 11/12/2008
More informationJEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4
JEEP JK4 STEP SLIDER INSTALLATION BD-SS-100-JK4 PARTS LIST QTY DESCRIPTION 1 Drivers Side Slider Assembly 1 Passenger Side Slider Assembly 1 Wiring Harness and Fuse 1 Double Sided Sticky Squares and Alcohol
More informationRetrofit Steering Column Installation Instructions
Retrofit Steering Column Installation Instructions for 1967 Mustangs www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 PH: (517) 424-0577 FAX: (517) 424-7293 Revised 9/29/2009 Instruction #: 8000000014
More informationBucket Harness. Installation Instructions. for Electric Club Car Precedent
Bucket Harness for Electric Club Car Precedent Installation Instructions Electric Club Car Precedents manufactured after January 1, 2008 require an additional harness to allow the installation of light
More informationIAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
More informationINSTALLATION AND OPERATION MANUAL
INSTALLATION AND OPERATION MANUAL 40 /42 2009 and Newer Timpte STD/Split Tub Style Hopper Trailers KIT #100513 40/42 96w - KIT #101026 40/42 102w Thunderstone Manufacturing, LLC. 3400 West O Street Lincoln,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publication No. MII 15249 WINCH MOUNT KIT P/N 08L70-HL3-A41 SXS700/M4/M2 Issue Date September 2015 PARTS LIST No. Description Qty (1) Winch bracket 1 (2)
More information2015+ HELLCAT 6.2L HEMI System vehicle specific plate system xx
These installation instructions will guide you through installing the Nitrous Outlet 2015+ Hellcat 6.2L Hemi Vehicle Specific Plate System on your vehicle. Before you get started, remember to never use
More informationRetroAir JAGUAR XKE S1-3.8 LHD FULL KIT CONTENTS:
RetroAir JAGUAR XKE S1-3.8 LHD FULL KIT 2-12-2011 CONTENTS: 1- Custom Design Evaporator Case &Core Assembly 1- Universal Bracket (installed) Evaporator Pak includes: 2-Custom Brackets; 2-1-¼ Grommets;
More informationAlliance Towel Dispensing System. Operation Manual
Alliance Towel Dispensing System Operation Manual Alliance Towel Dispensing System Table of Contents Safety Information... page 2 Mounting Instructions... page 3 Towel Loading Instructions... page 7 Settings...
More informationInstallation Instructions for John Deere cotton stripper models:
Installation Instructions for John Deere cotton stripper models: 7445 7450 7455 IMPORTANT: Ensure the instructions you use for the installation correspond to the machine model. If you receive the incorrect
More informationSYNERGY SUSPENSION UNIVERSAL FRONT 3-LINK KIT Version 1.0
5051 - SYNERGY SUSPENSION UNIVERSAL FRONT 3-LINK KIT Version 1.0 GENERAL NOTES: These instructions are also available on our website; www.synergymfg.com. Check the website before you begin for any updated
More informationRH INSTALL INSTRUCTIONS 2008 MODEL
RH-800-2 INSTALL INSTRUCTIONS 2008 MODEL 1 Tips for Installing Rhinogear Products The recommended sequence for installing our Rhinogear line of products on your Rhino. This sequence will help with ease
More informationFARM MODEL INSTALLATION INSTRUCTIONS
REAR ATTACHMENT ELECTRIC CONVERSION FARM MODEL INSTALLATION INSTRUCTIONS This page intentionally left blank MICHEL S INDUSTRIES, LTD. p.o. Box 119 St. GREGOR,SK PH: 306.366.2184 em: SALES@MICHELS.CA 1
More informationEbling Back Blade Snow Plow Wireless Controller Kit Only sold by SnowplowsPlus.com and ControlAllWireless.com
Ebling Back Blade Snow Plow Wireless Controller Kit Only sold by SnowplowsPlus.com and ControlAllWireless.com WARNING Always unplug the plow or shut off the battery breaker when in transport or not in
More informationDODGE RAM 2500
81234007 2014-2015 DODGE RAM 2500 Congratulations - your new LevelTow Helper Springs are quality products capable of improving the handling and comfort of your vehicle. As with all products, proper installation
More informationINSTALLATION INSTRUCTION
1551 S. Vineyard Avenue Ontario, CA 91761 (909) 923-1973 INSTALLATION INSTRUCTION Club Car Precedent Installation Notes CURTIS 1234, 1236 OR 1238 AC INDUCTION MOTOR/ CONTROLLER REVISION: B This kit is
More information*NOTE* The following suspension system will not work with heavy duty axle housings as pictured below.
1964 ½ - 1970 Ford Mustang Triangulated 4-Link Suspension Installation Instructions Tech Line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work!
More informationPump Gas Instructions for Polaris And 800 Models. Important Information before Installing This System:
Pump Gas Instructions for Polaris 600 700 And 800 Models Important Information before Installing This System: Before you begin your turbo install, read through these instructions to determine if you are
More informationInstallation Guide 50342/ Kargo Master Safari Rancho Cordova, CA
Installation Guide 50342/50352 Kargo Master Safari Rancho Cordova, CA 95742 800-343-7486 CustomerService@Safari.com *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING, INSTALLING AND USING
More informationJB N20/N26 Stage 1 & JB4 Install Guide Last Updated: 10/31/2017
JB N20/N26 Stage 1 & JB4 Install Guide Last Updated: 10/31/2017 Use subject to terms and conditions posted at http://www.burgertuning.com/terms.html THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING
More informationAdjustable Light Kits E-Z-Go TXT All Models Installation Instructions
Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationTusk Pannier Racks. Instructions and information KLR
1 Tusk Pannier Racks Instructions and information KLR650 2008 + Congratulations on your purchase of the Tusk Pannier Racks. These racks are made to handle extreme adventure riding, but work great for the
More informationLankota, Inc. LAN Installation Instructions
Lankota, Inc. LAN - 84108 Installation Instructions Converts 90 Series Corn Heads With Hydraulic Deck Plates To Single Point Hook Up On 60 series combines. Kit LAN-84108 Lankota is the trademark for Lankota,
More informationIncluded parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/ Hardware STEP 1
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please contact H&S Motorsports
More informationROADRELAY 5 Installation Guide
ROADRELAY 5 Installation Guide ROADRELAY 5 Installation Guide Bulletin No. 4971214 Revision A Copyright 2011, Cummins Inc. All rights reserved. Cummins Inc. shall not be liable for technical or editorial
More informationPARTS LIST: 8581 DODGE LONG ARM BRACKETS 03-13
SYNERGY MFG. 870 INDUSTRIAL WAY, SAN LUIS OBISPO, CA (805) 242-0397 8580 03-12 DODGE 2500/3500 4X4, 06-08 1500 MEGACAB 4X4 LONG ARM SUSPENSION KIT V3.0 GENERAL NOTES: These instructions are also available
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publication No. INSTALLATION INSTRUCTIONS WINCH MOUNT KIT P/N 08L77-HL3-A00 SXS700M4/M2 Honda Dealer: Please give a copy of these instructions to your customer. MII 14607 Issue Date
More informationClub Car 1515 to Curtis 1268 Conversion
Club Car 1515 to Curtis 1268 Conversion Installation Instructions 62-12685501CKXI Rev. 03 4/17/14 Page 1 of 7 1515 to Curtis 1268 Conversion Installation Instructions Before you start turn Tow/Run switch
More informationEasy Cover. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 944 Easy Cover Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 00-3-94 www.aeroindustries.com Indianapolis,
More informationKit INSTALLATION GUIDE. 5 psi Low Pressure Sensor (Single Gauge)
ª Kit 25592 5 psi Low Pressure Sensor (Single Gauge) MN-333 (131107) ECR 7119 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before proceeding with installation.
More informationDetroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &
Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.
More informationGeneral Front Windshield
General Front Windshield **WATCH OUR INSTALL VIDEO ALONG WITH INSTALL SHEET. 8-5/16-18x1 Black Carriage Bolts 8-5/16 Black Nylock Nuts 2-5/16x1-1/4 Stainless Steel Socket Head Screws 2-Rubber Grommets
More information2-Fryer Battery Wiring Restraint Kit Fryer Battery Wiring Restraint Kit Fryer Battery Wiring Restraint Kit
McDonald s Common Electric Enhancement Instructions IMPORTANT: Before beginning this work, ensure the coverage acknowledgement and prework checklist have been completed and signed by the owner/store manager
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationKit psi Low Pressure Sensor (Dual Gauge)
ª Kit 25812 5 psi Low Pressure Sensor (Dual Gauge) MN-337 (111107) ECR 7119 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before proceeding with installation.
More informationCongratulations on purchasing the Edge Juice/Attitude system for the Dodge Cummins Diesel.
Getting Started About the Juice Congratulations on purchasing the Edge Juice/Attitude system for the Dodge Cummins Diesel. The Juice/Attitude system features an intelligent module (Juice) that acts as
More information60-72 Chevrolet C10 Power Rack & Pinion Kit Instructions # , , &
60-72 Chevrolet C10 Power Rack & Pinion Kit Instructions # 8011740-01, 8011900-01, & 8011920-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W
B&W Trailer Hitches 6 Hawaii Rd / PO Box 86 Humboldt, KS 66748 P:60.473664 F:60.869.903 Turnoverball Gooseneck Hitch Installation Instructions MODEL 08
More information120V Low Ice Level Light Kit Installation Instructions
120V 1A 1B Parts Included in Kit No.: 5030224 Qty. Description Part Number 1.. Temp. Control..00219483 1.. Label Wiring Low level Light.5030180 1 Harness Low Level Light...5029920 1.Template Sensor Locating...5029916
More informationadvanced FLOW engineering Instruction Manual P/N:
advanced FLOW engineering Instruction Manual P/N: 42-24011 Make: GM Model: Diesel Trucks Year: 2001-2016 Engine: V8-6.6L (td) Duramax Fuel Pressure: 8-10 psi (relay controlled) Supported Horsepower: 2000+
More informationINSTALLATION INSTRUCTIONS For 2007 and newer Jeep Wrangler JK
7 LED sealed beam headlamp with switchback Halos and DRL INSTALLATION INSTRUCTIONS For 2007 and newer Jeep Wrangler JK SB7250XX-BLK, SB7250XX-CHR, SB7050BA-BLK, SB7060XX-BLK, SB7060XX-CHR, SB7160XX-CHR,
More informationSupported Models: Ag-Chem Terragator 6103, 6203 Ag-Chem Terragator 8103, AutoFarm GPS AutoSteer. Hardware Installation Guide
Supported Models: Ag-Chem Terragator 6103, 6203 Ag-Chem Terragator 8103, 8203 AutoFarm GPS AutoSteer Hardware Installation Guide P/N: 602-0147-01-A January 2008 Special Requirements Tools This list consists
More informationSTOP---READ THIS FIRST!
STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2003-2013 DODGE Ram 2500/3500, 8 LIFT KIT NOTE: * The factory wheels and tires WILL fit on the front of the vehicle once
More informationC50254A PH3 AIR INTAKE SHUT-OFF VALVE DODGE 6.7L CUMMINS WITH POWERGUARD SMART OVERSPEED LIMITER
AIR INTAKE EMERGENCY SHUT-OFF VALVE C50254A PH3 AIR INTAKE SHUT-OFF VALVE WITH POWERGUARD SMART OVERSPEED LIMITER 2013-2017 DODGE 6.7L CUMMINS www.powerhalt.com INSTALLATION REQUIREMENTS & RECOMMENDATIONS:
More informationPowerslot Mustang Rotors (Rear Pair GT/V6) - Installation Instructions
Powerslot Mustang Rotors (Rear Pair 94-04 GT/V6) - Installation Instructions The below installation instructions work for the following products: Powerslot Mustang Rotors (Rear Pair 94-04 GT/V6) Please
More informationCombine Cover Manual
Combine Cover Manual Installation Instructions Page 26 Operating Instructions Page 7 Warranty Page 7 Trouble Shooting Page 8 10 For Big Top Extension Model s: Case I.H. 8010, 8120 Please forward onto Customer
More information67-70 Cougar Rack Kit Instructions # &
67-70 Cougar Rack Kit Instructions # 8011950-01 & 8011940-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty on
More information***THE OWNER'S MANUAL MUST BE GIVEN TO THE END USE CUSTOMER AFTER COMPLETING THE INSTALLATION.***
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE HARLEY MECHANICAL REVERSE 1999-2006 FIVE SPEED FLH LAST UPDATED: OCTOBER 2011 AS THE INSTALLER OF THIS MECHANICAL REVERSE, YOU MUST BECOME FAMILIAR WITH PROPER
More informationToyota Prius Interior Light Upgrade
Toyota Prius 2012- Interior Light Upgrade Part Number 00016-00095 Accesory Code: IL2 Conflicts Kit Contents Item # Quantity Reqd. Description 1 1 Y Adapter 2 1 Wire harness 3 1 Hardware Kit 4 2 White Light
More informationTJ YJ LJ STEP SLIDER INSTALLATION
TJ YJ LJ STEP SLIDER INSTALLATION BD-SS-100-TJ, BD-SS-100-YJ, BD-SS-100-LJ PARTS LIST QTY DESCRIPTION 1 Drivers Side Slider Assembly 1 Passenger Side Slider Assembly 1 Wiring Harness 1 Double Sided Sticky
More informationTable Of Contents TABLE OF CONTENTS INTRODUCTION INSTALLATION OPERATING INSTRUCTIONS APPENDIX ABOUT THE JUICE... 3 SAFETY TERMS...3 INTRODUCTION...
Ford Juice installation Instructions **read important safety information in this manual** TABLE OF CONTENTS F o r d J u i c e Table Of Contents ABOUT THE JUICE... 3 SAFETY TERMS...3 INTRODUCTION... 3 PRODUCT
More informationNew Holland TC30 Parts List & Mounting Instructions
New Holland TC30 Parts List & Mounting Instructions Jodale Perry Printed: 2003/07 Standard Parts List Qty Description Photo Front Brackets 4 Front Bracket Spacers Rear Brackets Rear Bracket Axle Supports
More informationAssembly & Installation Instructions
TM P R O D U C T S Assembly & Installation Instructions FOR 28 SERIES SNOWPLOW PIVOT ASSEMBLY AND FLOAT LIMITER 99103000 FOR SERIAL NUMBERS 28D100000 TO 28D100770 97100552A 1. THINK SAFETY, ALWAYS WEAR
More informationIntroduction. Installation. Maintenance. Bill of Materials
Table of Contents Introduction Specitications... 3 Operation... 4 Installation New Installations... 6 Retrofit Installations... 6 Flow Control Switch... 7 Dimensions... 8 E-7 Valve... 28 E-7 Valve with
More information09-12 Dodge 4WD /4 Body Lift
92RC80000 09-12 Dodge 4WD 1500 1 1/4 Body Lift Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this kit. Attempts to install
More informationWiring for OMS/Mid-engine layout
Wiring for OMS/Mid-engine layout Coil connectors Crank sensor Coolant temperature sensor Cam sensor Connector for fuel pump Connector for joining new wiring harness to existing Suzuki wiring will need
More informationIowa State FFA Agricultural Mechanics Career Development Event 2016
CONTESTANT NAME CONTESTANT SCHOOL Structural Systems Carpentry Skill Your FFA chapter has been selected to work with Iowa State Fair set up for the hog show. The state fair has decided to construct wood
More informationDetroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &
Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.
More informationYamaha Apex Moto-R Kill w/jacobson Roll-over valve Installation Instructions
OFTRacing.com Email Scott Moto 2006-2011 Yamaha Apex Moto-R Kill w/jacobson Roll-over valve Installation Instructions Included Parts: 1 Moto-r Kill wiring harness including Pro Armor tether switch, Jacobsen
More information3 in 1 TRAIL CHARGER with LOCKOUT
Owner s Manual P/N: 283821 500 3 in 1 TRAIL CHARGER with LOCKOUT 283821 01 Version 2.04 07/05/2011 Owners Manual Operation Installation Wiring Diagram Troubleshooting Parts Breakdown 1 GENERAL OPERATION
More information09-12 Dodge 4WD Leveling Kit
9235900 09-12 Dodge 4WD 1500 2.5 Leveling Kit Thank you for choosing Rough Country for all your suspension needs. DOES NOT FIT TRX PACKAGE VEHICLES!! Rough Country recommends a certified technician install
More informationDigitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers
Supersedes IL 33-858-4 Dated 05/02 Digitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers Digitrip Retrofit System for ITE K-3000, Digitrip Retrofit System for ITE K-3000, K-3000
More informationCongratulations on your purchase from Rigid Industries, here are the instructions for installation of your new Rigid Lights.
Congratulations on your purchase from Rigid Industries, here are the instructions for installation of your new Rigid Lights. 20 E-Series LED Light Bar with Cradle for Lower Grill Mount. Dually Fog Lights
More informationRZ3-5K Polaris RZR XP 1000 & 900 Kicker 5 Speaker Audio Kit
PO H PWER PO 5 O KIT I E D U A S A TS S I R LA R Z R R O SP pg 2 pg 9 pg 13 pg 25 pg 29 Disassembly, Wire and Amplifier Plate Installation Glovebox Subwoofer Installation Kick Panel Speakers Installation
More informationHeater/Defroster Installation Instructions
1301 39 th Street NW, Suite 2 * Fargo, ND 58102 * Toll Free 866.764.0616 * Fax 701.446.0103 * www.gemcar.com Service Instructions Heater/Defroster Installation Instructions Models: All 2005 - Current Part
More informationInstallation Instructions
86-95 Low Range Off Road Universal Front Shock Tower Kit for Suzuki Samurai (SKU# SSP-UST) Installation Instructions Revised 10/29/13 Suggested Tools: CAUTION: Safety glasses should be worn at all times
More informationM14 AUTOMOTIVE SPARK PLUGS AND WIRES CONVERSION KIT INSTALLATION INSTRUCTIONS
M14 AUTOMOTIVE SPARK PLUGS AND WIRES CONVERSION KIT INSTALLATION INSTRUCTIONS (It is highly recommended you read the instructions completely before beginning) 1. Be sure the magneto switches are turned
More informationLIFT-304 (3 ) and LIFT-104 (6 ) Drop Spindle Lift Kits Yamaha G22, Gas or Electric Installation Instructions
LIFT-304 (3 ) and LIFT-104 (6 ) Drop Spindle Lift Kits Yamaha G22, Gas or Electric Installation Instructions LIFT-304 LIFT-104 Contents of LIFT-304/104 Yamaha G22 Lift Kit: a (1 ea.) Passenger Side Spindle
More informationSKID MARK GARAGE. Axillary Fuel Supply
1 SKID MARK GARAGE Axillary Fuel Supply *Disclaimer: Our Axillary Fuel kits are designed to fit most late model GM vehicles with minimum modifications. While not quite a universal kit for all, it has been
More informationSTEP 1 STEP 2. Disconnect the negative terminal from both batteries.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationUniversal Tall HoneyBadger Chase Rack Installation Instructions
PREPARATION Universal Tall HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend
More informationRunner w/x-reas -2 Front 1 Rear Leveling Kit
92176700 2010-2018 4 Runner w/x-reas -2 Front 1 Rear Leveling Kit Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician install this system. In
More informationRZ3-5A Polaris RZR XP 1000 & 900 SSV Works 5 Speaker Audio Kit
RZ3-5A Polaris RZR XP 1000 & 900 SSV Works 5 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25
More informationColor LaserJets 3000, 3600, 3800, and CP Main Drive Assembly Replacement and Timing
Work Instruction Color LaserJets 3000, 3600, 3800, and CP3505 - Main Drive Assembly Replacement and Timing Security Level: HP and Channel Partner Internal Use Date Written/Updated: 8/14/09 Document Number:
More informationDODGE Ram 1500 Mesh Grille
921701970 DODGE 2013-16 Ram 1500 Mesh Grille Thank you for choosing Rough Country for all your lighting needs. Please read instructions before beginning installation. Check the kit hardware against the
More informationFitting Instructions. Revo MQB Golf/GTi/Octavia/Leon Intercooler. Recommended Tools. Contents RV581M Dealer installation advised.
RV581M100100 Recommended Tools Contents No. Description Tools Size Intercooler Torx Bit T25, T30 Bracket Kit llen Key 4, 5 mm Silicone Hoses Socket 7, 10, 16, 19 mm Hose Clamps Flat Head Screwdriver Small,
More informationLGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions
LGT-311L Bumper LED Light Kit EZ-Go RXV Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative connections
More informationAt-A-Glance Trailer Assembly Overview
At-A-Glance Trailer Assembly Overview VERY IMPORTANT; ALWAYS REFER TO YOUR OWNER S MANUAL FOR PROPER OPERATING AND SAFETY INFORMATION REGARDING YOUR TRAILER. INCASE OF LOSS GO TO WWW.UTILITYMATE.COM BEFORE
More informationRCA PLUG KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RCA PLUG KIT P/N 2883824 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationASSEMBLY MANUAL. 45-Foot Air Double Disc Drill. Amity Technology, LLC th Avenue North Fargo, ND (701)
ASSEMBLY MANUAL 45-Foot Air Double Disc Drill Amity Technology, LLC 2800 7th Avenue North Fargo, ND 58102 (701) 232-4199 www.amitytech.com TABLE OF CONTENTS Main Frame 1 Wing Lock Towers 3 Wing Frames
More information