Installation Instructions for John Deere cotton stripper models:

Transcription

1 Installation Instructions for John Deere cotton stripper models: IMPORTANT: Ensure the instructions you use for the installation correspond to the machine model. If you receive the incorrect installation instructions, contact Ag Leader Technology Technical Support at (515) ext. 1. September

2

3 Ag Leader Technology Cotton Stripper Installation Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No Instruction Kit JD Arm Assy (18 in rod, S-hook, 16 in. chain, spring) Header Sensor Standard Cable Kit Cotton Stripper JD 7450/ Ground Speed Cable 14 XX-16XX Elevator/Fan Speed Cable 10 ft Flow Cable Detector JD Stripper Flow Cable Emitter JD Stripper WP Plugged Tower 3 Pin Distribution Cable 8 in. Cotton Cab Cable Cotton JD 9965/70/76, 7450/ Cable Inst. Kit Cotton Stripper Drill Bit Tin Coated - # Drill Bit Steel 1/4 in Self Tapping Hex Slotted Hd Screw, Coarse Thd, Gr 5, #8 x 3/8 in. Alcohol Swab Pack Grey Plastic Cable Clamps Cable Tie 15 in. Black Cable Tie 6 in. Black Adhesive Mounting Base 2 way Cable Clamp 1/2 x 1/2 in. wide Cable Clamp 3/4 x 1/2 in. wide Parts Kit JD Cotton Stripper Cab Wall Plate Kit (21xx, 9x50, ) in. U-Bolt in. U-Bolt Clamping Plate Drill Bit Steel Jobber 9/32 in Drill Bit Tin Coated 11/32 in Transfer Punch 11/32 in File Square 5/16 in Silicone Rubber Adhesive Sealant Black 2.8 oz File Handle Monitor Bracket Inst. Kit Hardware Kit JD Cotton Stripper Pen Black Permanent Fine Post Bracket September

4 Cotton Stripper Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part No Emitter Assembly Cotton, 5 position Detector Assembly Cotton, 5 Position Antenna Mounting Plate (with dual-lock) Shield Cotton Detector (JD Stripper) Mounting Plate Cotton Detector Asm (JD Stripper)r Mounting Plate Cotton Emitter Asm (JD Stripper) Template-hinged (JD Stripper) Hinge Cotton Stripper Shield Template, Hole Pattern Cotton Stripper September

5 Ag Leader Technology Cotton Stripper Installation Important Notices You will save time and prevent wrong installation of components by closely following the step-by-step instructions. If you have questions, call Ag Leader Technology at Signal words (CAUTION, IMPORTANT and NOTE) are provided to draw attention to information that is important for the safe/correct installation and operation of this product. CAUTION will alert you to situations that will impact the physical safety of you or others. IMPORTANT will alert you to the potential for damage to the product or loss of data. NOTE will provide you with additional information to simplify a procedure or clarify a process. Place the Installation instructions and Parts Lists in their sections in the Operator s Manual to prevent their loss or to use as reference after completing installation. Section Contents Item Page Installing PF Series Monitor in Cab 9-2 Connecting Power Cable 9-5 Installing Distribution Cable 9-7 Installing Fan Speed Cable 9-9 Installing Ground Speed Cable 9-11 Installing Header Height Sensor 9-12 Installing Flow Sensors 9-15 Installing Flow Sensor Cables 9-31 Final Inspection 9-35 Operational Checkout 9-36 September

6 Cotton Stripper Installation Ag Leader Technology Installing Monitor in Cab Parts required for this procedure: Monitor Unit Post Bracket U-Bracket Screw-mount cable-tie base, mounting screw and cable ties. Cab Cable Monitor Bracket Install Kit (screws, bolts, washers and nuts) Step-by-Step Procedure 1. Using the hardware from the monitor install kit, attach the post bracket to the u-bracket as shown in Figure 1. NOTE: If installing a YM2000, PF3000 or PF3000 Pro monitor, mount the u-bracket in the same position as shown in Figure 1. Figure 1. Monitor Bracket Assembly 9-2 September

7 Ag Leader Technology Cotton Stripper Installation 2. Position the post bracket assembly along the right side of cab. Move the assembly forward or backward to obtain the optimum position for your viewing. Figure 2 is the recommended mounting position. Figure 2. Post Bracket Mounting Location 3. Using the post bracket as a template, mark three mounting holes on the right upper sidewall of the cab as shown in Figure 2. September

8 Cotton Stripper Installation Ag Leader Technology 4. Center punch and drill the mounting holes with the provided 13/64 inch drill bit. 5. Attach the post bracket to the cab wall with three 1/4x3/4 inch selftapping screws. 6. Reattach the u-bracket to the post bracket (See Figure 1). 7. Mount the monitor in the bracket. IMPORTANT: Never use force to mate electrical connectors. If the connectors do not push together easily, they are not aligned properly. Using force will only result in damage to the connectors. 8. Connect the cab cable to the monitor. 9. Route the cab cable from monitor to the distribution cable, by going down the center post and then along the cab floor back to the distribution cable. Tie the cab cable to center post with cable ties. 9-4 September

9 Ag Leader Technology Cotton Stripper Installation Connecting to Switched Power for 7445 Parts required for this procedure: Pigtail off cab cable. Step-by-Step Procedure 1. The pigtail originating from the 24-pin connector of the cab cable needs to be connected to switched power. 2. The key switch on the control console to the right of the driver's seat is where switched power can be found. 3. The female spade connector of the pigtail will connect to an unused male spade connector on the key switch. 4. In order to rout the pigtail through the control console, several screws need to be removed and an access panel facing the seat can be moved. 5. The pigtail can be routed from the back left of the control console in toward the right cab wall and then forward to the key switch. Installing Power Cable for 7445 Parts required for this procedure: Power cable (cable with a yellow inline fuse holder) Cable ties Step-by-Step Procedure 1. At the battery connect wire without the yellow fuse holder to the negative terminal by installing the ring terminal on the battery terminal clamp bolt. 2. At the battery connect the wire with the yellow fuse holder to the positive terminal by installing the ring terminal on the battery terminal clamp bolt. 3. Route the power cable to the area under the cab by passing it under the bracket between the engine compartment and the battery compartment. Bend the middle tab of the bracket, which separates the two main wiring harnesses up so the battery cable can pass through. September

10 Cotton Stripper Installation Ag Leader Technology 4. Route the battery cable along the existing wire harness and fan/ground speed sensor cables under the cab. 5. Connect the power cable to the distribution cable. 6. Turn the monitor ON. If it does not power up, immediately shut it off and make sure you have the power cable wires connected to the correct terminal on the battery. NOTE: Be sure to route the cable and tie it down so that pinching or rubbing against sharp edges cannot damage it. Connecting Power Cable 7450/55 Step-by-Step Procedure Parts required for this procedure: Pigtail off cab cable 1. Route the power pigtail from the cab cable to the front of the console. 2. Place the cable between the window and the console. 3. Remove power cap on the 3-spade power source located at the front of console. 4. Mate power pigtail to connector on console. See Figure Turn the machine ignition switch on the ON position and turn the monitor ON. If the monitor does not power up, turn power switch off and recheck the cable connections. Figure 5. Power pigtail connected. 9-6 September

11 Ag Leader Technology Cotton Stripper Installation Installing Distribution Cable Step-by-Step Procedure Parts required for this procedure: Distribution Cable Cab Wall Bracket Kit Drill bit 1. Locate the hole under the floor mat in the right rear corner of the cab. See Figure Fasten the cab wall bracket to the square flange of the round connector of the cab cable using four #6-32 x1/2 inch screws with nuts and lock washers. 3. Hold the bracket flush against the floor of the cab so the square flange if the round connector is facing up and centered in the hole. Mark in the center of one of the corner holes of the bracket. 4. Remove the bracket and make a center punch mark on the pen mark. Use the #7 drill bit to drill a hole for a 1/4 inch self tapping screw. 5. Hold the bracket in its mounting position ensuring it is flush with the floor and install the 1/4 inch self tapping screw. 6. With the bracket held in its mounting position, center punch and drill the three remaining corner holes of the bracket. Install three remaining 1/4-inch self-tapping screws. 7. From outside the cab, connect the round 24-pin connector of distribution cable to the round 24-pin connector of cab cable. 8. Loop any excess cab cable and secure it with a cable tie. September

12 Cotton Stripper Installation Ag Leader Technology Figure 6. Hole in right rear corner of cab floor. Figure 7. Cab Cable and Distribution Installed. 9-8 September

13 Ag Leader Technology Cotton Picker Installation John Deere 9970 Installing Fan Speed Cable Parts required for this procedure: Fan speed cable Cable ties Step-by-Step Procedure 1. Locate Fan Shaft Speed Sensor at the front end of fan blower (just above the lower frame rail about halfway between the front and rear wheels on the left side of the machine). 2. Install the two-connector end of the fan speed cable, to the jumper between the existing wiring harness and fan shaft speed sensor. 3. Tie fan speed cable to existing cables as shown in Figure 8. Cable ties Cable connection Figure 8. Fan Speed Cable Connection at Fan Blower Shaft September

14 Cotton Stripper Installation Ag Leader Technology NOTE: In all steps, tie the fan speed cable in 12 to 18 inch intervals. Be sure it is tied down well enough to keep it away from moving parts. 4. Follow existing machine wiring to the right side of the machine and forward from the fan blower. Be sure to tie it securely where it passes near moving parts. 5. When the cable is routed to the right side of the machine, route the cable forward along the existing electric wiring to the cab. 6. Begin routing the fan speed cable along the hydrostatic pump control push/pull cable. Follow this cable to the area under the steering column and connect the fan speed cable to the distribution cable. NOTE: If your fan speed does not operate correctly and you have properly set the fan pulse you should check the distance the sensor is from the wheel. If there is an excessive gap, the sensor will not function correctly. The gap should be no more than 1/16 inch. See Figure 9. 1/16 inch gap between wheel and sensor Figure 9. Fan Speed Sensor 9-10 September

15 Ag Leader Technology Cotton Stripper Installation Installing Ground Speed Cable Parts required for this procedure: Ground speed cable Cable ties Step-by-Step Procedure 1. Locate ground speed sensor on top or side of the drive transmission (just behind the center of the front axle). 2. Install the two-connector end of the ground speed cable, to the jumper between the existing wiring harness and the ground speed sensor. 3. Route the cable to the right side of the machine as shown in Figure Route the cable with the previously installed fan speed sensor cable until you reach the cab. 5. Route the cable under the cab securing it at inch intervals and connect the ground speed cable to the distribution cable. Cable connection Figure 10. Ground Speed Cable Connection at Transmission September

16 Cotton Picker Installation John Deere 9970 Ag Leader Technology Installing Header Height Sensor Parts required for this procedure: Header height sensor assembly (with integral cable) Two 5/16 x 1 inch bolts with lock washers and nuts Arm assembly (threaded rod with S-hook) S-hook Cable ties Step-by-Step Procedure 1. Position the header sensor under the cab so that: 1a. The sensor is mounted on the right most cab support member. See Figure 11. Mark two of the slots onto the support member where you will drill and mount the sensor with bolts. 1b. While holding the sensor in place, temporally insert the threaded arm into the shaft to verify there is no interference. Arm may need to be bent after installation to avoid hitting other components. 2. Drill a 3/8 inch hole, on the marks made in Step 1a. Figure 11. Sensor mounted on right side of support member September

17 Ag Leader Technology Cotton Stripper Installation 3. Install two 5/16 x 1-inch bolts through the drilled holes and side row of holes in the side of sensor frame. Between the sensor and the support member you are mounting to, place several washers provided in the hardware kit, to allow for the stud and nut protruding on the side of the sensor. Without the washers, the sensor will be bent and damage may occur as the fasteners are tightened. 4. Install the arm assembly in the hole in the sensor pivot shaft with a nut and lock washer on each side of the shaft. 5. Verify arm alignment and tighten bolts to support member. IMPORTANT: Do not apply excessive torque. This can deform the sensor frame and prevent proper operation. Tighten nuts only enough to firmly hold the sensor in place and then check to see the arm pivots smoothly and always returns to the spring centered position. 6. Connect the free end of the chain to the S-hook on arm and pinch the hook closed. The spring is supplied for various mounting locations. It is recommended to remover the spring as it may stretch and thus lose any header height settings in the monitor. This may cause you to unexpectedly stop logging data. Additional chain length may be needed, depending on mounting location, so when header is all the way down, the header height is not pulled off. Figure 12. Securing the chain to the main lifting arm of the header. (Picture indicates the use of a hose clamp; instead a U-bolt Clamping plate and S-Hook is provided) September

18 Cotton Stripper Installation Ag Leader Technology Figure 13. Back view of header sensor showing its mounting and bending in the arm to avoid hitting other components of the machine. 7. Mount the U-bolt, clamping plate, and S-hook to the right main lifting arm of the header. Mount it so that the S-hook and nylock nuts are on the top of the lifting arm. 8. Secure the end of the chain to the S-hook secured to the U-bolt on the main lifting arm of the header. See Figure 12. IMPORTANT: Ensure the chain will be clear of any rotating shafts and does not pull on the rod at an extreme side angle. 9. It may be necessary to bend the threaded rod to prevent interference with other components. See Figure Route header sensor cable to the area under the cab to the distribution cable. 11. Connect header sensor cable to the distribution cable September

19 Ag Leader Technology Cotton Stripper Installation Installing the Flow Sensors It is important that you closely follow the instruction and measure carefully in order to achieve the correct sensor alignment. Sensor installation overview: 1. You will begin by locating and drilling two holes on the back of the cleaner. 2. Temporarily Mount the emitter mounting bracket on the back of the cleaner and mark the appropriate holes. 3. Remove the mounting bracket and make all of the appropriate holes and cuts then remount the emitter bracket and use the special template to make a center punch mark on the other wall of the cleaner. 4. Drill the two center punched holes and bolt the thin flat galvanized template on the inside surface of the cleaner and mark all of the holes and slots. 5. Remove the template and cut and drill the inside wall of the cleaner. 6. Mount the detector bracket and sensor shield. Refer to Figures 14, 15 and 16. Figure 14. Picture showing the back of the cleaner with the emitter mounting plate and emitters installed. September

20 Cotton Stripper Installation Ag Leader Technology Figure 15. Side view of Complete Sensor installation Figure 16. Detector mounting plate inside the cleaner September

21 Ag Leader Technology Cotton Stripper Installation Sensor Installation CAUTION: To prevent death or injury to you or others, ensure the basket lock is engaged before accessing the area under the basket. The basket lock is located near the front cylinder that raises the basket. IMPORTANT: To prevent damage to electrical components on the machine, disconnect the 3 wire connecting block located under the cab before welding or cutting on the machine with a plasma torch. The connectors are located under the console, you need a 9/32 inch socket and extension to disconnect. See Figure 17. Figure 17. Connecting block under the cab. IMPORTANT: To prevent damage to the doffer brushes, remove the cover on the back of the cleaner and use the two small engine shields to lay over the doffer brushes. This will prevent tools and hardware from falling down into the Cleaner Fan. See Figure 18. September

22 Cotton Stripper Installation Ag Leader Technology Figure 18. Engine covers over the Doffer Brushes. 1. Begin by locating the center of your cleaner on the basket side. Measure across the base of the cleaner and mark a center point. Using a framing square, draw a line up the center of the chute using the center mark for alignment. One of the mounting bolts is actually at the center. See Figure From the centerline and base of the cleaner, locate the top two holes where the emitter mounting bracket will mount (larger bracket as shown in the pictures). Measure from the flange See Figure 20 for the dimensions September

23 Ag Leader Technology Cotton Stripper Installation Center of Cleaner Figure 19. Locating the center of the cleaner. Figure 20. Dimensions to locate the first two mounting holes on the cleaner for the emitter-mounting bracket. September

24 Cotton Stripper Installation Ag Leader Technology Figure 21. Emitter mounting bracket temporally mounted on cleaner. 3. Drill the two holes using the 9/32 drill bit provided. 4. Mount the emitter mounting bracket (larger bracket) using the two holes you just drilled and the two top holes of the bracket. The orientation of the bracket should be as indicated in Figure 21. The row of 6 studs should be on the upper portion. 5. Using the black marker provided, completely mark each bolt hole and the large rectangular holes. IMPORTANT: You must also mark the large rectangle holes. You will measure from the rectangular holes to locate the hole you will cut in the back of the chute. 6. Remove the bracket from the cleaner. 7. Measure the required distance to locate the perimeter of the hole to be cut. Refer to Figure 22 for these dimensions. Obviously the bracket will not be on the cleaner (as shown in the picture), however, the marks from the rectangular holes will be on the cleaner September

25 Ag Leader Technology Cotton Stripper Installation Figure 22. Use these dimensions to mark the hole to be cut. 8. Once the marks are made to locate the perimeter of the hole, connect the marks to make a complete outline of the hole. See Figure Center punch and drill all of the holes marked with the 9/32 inch bit. It is recommended to drill the holes before cutting the large rectangular hole, since the drilling area will be more secure before the hole is cut. If you have access to a hand punch, cut the rectangular hole first, and then punch all of the mounting holes. 10. Using a suitable cutting device, cut the area of the chute out previously marked. See Figure 23. A plasma cutter works well, however, an air grinder or reciprocating saw will work as well. A torch may be used but you must be very careful to maintain a smooth edge and you must remove any slag. You should try and keep a radius at the corners of the rectangular hole you are cutting to reduce the stress concentration and thus reduce the probability of cracking the cleaner. 11. Use a grinder or file to remove all burrs and slag from the edges of all holes. September

26 Cotton Stripper Installation Ag Leader Technology Perimeter of hole to be cut Figure 23. Perimeter of hole marked for cutting. IMPORTANT: You should use extreme caution when using any type of torch. Completely clean the machine of any cotton or plant material in the area below of where you will be cutting to prevent fires. It is suggested that a fire extinguisher be available during this procedure. IMPORTANT: It is recommended to shield the saw teeth, doffers and fans from any slag or parts that may fall on them and cause fire or damage. The engine shields along the side of the machine can be coupled together to provide an easy effective shield. IMPORTANT: After cutting the hole, remove any burrs or slag that may be on the inside surface of the chute. There must be absolutely NO burrs, as they will create cotton "stringers" that may affect yield accuracy September

27 Ag Leader Technology Cotton Stripper Installation 12. Once all holes are cut and drilled, you will need to temporarily remount the emitter mounting plate to transfer a mark to the inner wall of the cleaner to mount the other mounting plate. Use the bolts in the four corners and possibly one in the center to securely hold the plate in its final position. See Figure Place the hinged template into the left mounting bracket and secure it with two 1/4 inch nuts. See Figure Place the 11/32 inch transfer punch (provided) into the hole and onto the trough of the hinged template. Slide the transfer punch until it touches the inner wall of the cleaner. Using a hammer and a larger bolt or punch as an extension, hit the transfer punch to make a mark on the inner wall of the cleaner. Figure 24. Use the hinged template and transfer punch to transfer a mark to the inner surface of the cleaner. September

28 Cotton Stripper Installation Ag Leader Technology Figure 25. Center punch resting in guide of the hinged template 15. Repeat the previous step for the right hand side. 16. Remove the emitter-mounting bracket on the back surface of the cleaner. 17. Using the transfer punch, make a better center mark at the two marks previously made. Use a 1/4 inch drill bit if you have one to drill the holes, otherwise use the 9/32 inch drill bit provided. See Figure Use two 1/4 inch bolts to temporarily mount the galvanized template onto the inner surface of the cleaner. Mount the flat template oriented as it is marked. See Figure Mark all holes and slots with the black marker. There should be very small holes, 5 on the top and bottom, and 1 on each end that represent the mounting holes of the detector mounting plate September

29 Ag Leader Technology Cotton Stripper Installation Holes in inner wall Figure 26. Two holes in inner wall of cleaner to mount template Figure 27. Flat template secured by 2 bolts September

30 Cotton Stripper Installation Ag Leader Technology Figure 28. Template removed, lines from slots connected to form perimeter of section to be removed. Holes marked on inner surface of cleaner. 20. Remove the galvanized template. 21. Connect the lines to make the perimeter of the hole that will be cut. See Figure Center punch and drill all of the marks made with the galvanized template. Use the 9/32 inch drill bit, unless a handpunch will be used. 23. Using a suitable cutting device, cut the area of the chute out previously marked. A plasma cutter works well, however, an air grinder or reciprocating saw will work as well. A torch may be used but you must be very careful to maintain a smooth edge and you must remove any slag. 24. You should try and keep a radius at the corners of the rectangular hole you are cutting to reduce the stress concentration and thus reduce the probability of cracking the cleaner. IMPORTANT: You should use extreme caution when using any type of torch. Completely clean the machine of any cotton or plant material in the area below of where you will be cutting to prevent fires. It is suggested to have a fire extinguisher available in case of fire. IMPORTANT: It is recommended to shield the saw teeth, doffers, and fans from any slag or parts that may fall on them and cause damage or fire. The engine shields along the side of the machine can be coupled together to provide an easy effective shield September

31 Ag Leader Technology Cotton Stripper Installation IMPORTANT: After cutting the hole, remove any burrs or slag that may be on the inside surface of the chute. There must be absolutely NO burrs, as they will create cotton "stringers" that may affect yield accuracy. Figure 29. View of both rectangular sections removed. 25. Before mounting the detector mount on the inside of the cleaner, you must trim the bottom part of the middle two vanes. There are four vanes that attempt to evenly distribute the cotton over the saw drum as it enters the cleaner. Two inches of the bottom of the two middle vanes must be removed in order to mount the detector mounting plate. There is likely a spot weld in the area that must be broken loose or ground through. Once the spot weld is broken, you can cut a slot or a wedge at the 2 inch mark on the portion of the vane sticking out. You can bend the piece back and forth causing it to break from induced fatigue. Grind smooth any sharp edges and slag. See Figures 30. September

32 Cotton Stripper Installation Ag Leader Technology Remove lower 2 inches Figure 30. Lower 2 inches of middle vanes removed to mount plate. 26. Once all cutting, drilling and burr removal is complete, you may now mount the detector mounting plate. 27. Using the 1/4 x 1/2 inch bolts and flange nuts, mount the detector mounting plate so the heads of the screws are on the "clean" cotton side of the cleaner. The mounting plate should be mounted on the uncleaned side of the cleaner. See Figure 31 and 32. Figure 31. Detector mounting plate installed inside the cleaner, with shield hinged up 9-28 September

33 Ag Leader Technology Cotton Stripper Installation John Deere 7450/7455 Figure 32. View of detector mounting bracket and shield through square access hole of the front side of the cleaner. 28. Finally you can permanently mount the emitter mounting plate on the back side of the cleaner. Use the 1/4 x 1/2 inch bolts and flange nuts to fasten the bracket to the exterior of the cleaner. Mount the bolts so the heads are on the inside of the cleaner. 29. Mount the hinge as shown in Figure 33 and 34 with the head of the bolt to the outside. 30. Mount the shield to the hinge, as shown in Figure 33 and 34, with the heads of the bolt on the outside. For ease of installation, the nuts are already attached to the hinge. September

34 Cotton Stripper Installation John Deere 7450/7455 Ag Leader Technology Uncleaned Cotton side Shield Detector Mounting Plate Clean Cotton side Figure 33. Mounting plate mounted to the "uncleaned" side of the cleaner as opposed to the other "cleaned" side. Shield and hinge mounted to the detector mounting plate. Hinge Shield Figure 34. Orientation of the hinge and shield September

35 Ag Leader Technology Cotton Stripper Installation Installing the Flow Sensor Cables The flow sensor cable has two sides, one for the detectors (inside the cleaner) and one for the emitters (back side of cleaner). The cable for the detectors has a bulkhead connector that will mount to the side wall of the cleaner. The detector cable has large red/black connectors that mount to the detector (sensor without a cable). 1. Mark a spot on the side wall (opposite the basket dumping side) of the cleaner that is in line with the center of the bracket mounted inside the cleaner. Make the mark so the bulkhead connector, at the end of the detector cable, is as close as possible to the inner wall that the detector mounting bracket is attached to. Be careful and make certain the mounting surface is flat. Avoid the small piece that is attaching the inner wall to the side walls. See Figure 35. Figure 35. holes drilled in the side of the cleaner to mount the bulkhead connector. September

36 Cotton Stripper Installation Ag Leader Technology Figure 36. Bulkhead connector mounted to side wall of the cleaner. 2. Center punch the mounting location and drill using the hole saw provided. It is recommended to drill the centering hole from the inside and complete the cutting of the large hole from the exterior. See Figure Place the bulkhead connector through the hole on the outside to mark the four mounting holes (the cable will actually mount on the inside but in this application it is only used as a template for the four mounting holes). 4. Center punch the four marks and drill using the small drill bit included. 5. Push the connector from the inside so the connector portion is protruding to the outside of the cleaner. Using the self-tapping screws, fasten the bulkhead connector to the cleaner from the outside of the cleaner. See Figure 36 and Run the long portion of the emitter flow sensor cable to the distribution cable under the cab. The cable can be run along the top of the cleaner and down the main chute behind the cab, then through the opening around the main chute and connect to the distribution cable. Or the cable can be ran along the side of the cleaner and fasten with bolted cable clamps. See Figure 38. Tie any extra cable at the distribution cable to prevent it from being damaged. Use plastic ties to secure the cable as it runs to the distribution cable. 7. Tightly screw the emitter flow sensor cable onto the protruding portion of the detector cable September

37 Ag Leader Technology Cotton Stripper Installation John Deere 7450/7455 Figure 37. Bulkhead connector secured using self-tapping screws Figure 38. Cable routed along the side of the cleaner and attached using provided cable clamps. September

38 Cotton Stripper Installation John Deere 7450/7455 Ag Leader Technology Figure 39 Emitters and cables mounted on back side of chute. 8. Install the emitters (sensors with the cable) on the back of the cleaner. 9. Connect the emitters to its respective connector that was ran from the side of the cleaner. Route the cables through the slot on the side wall of the emitter mounting bracket. The lengths of the appropriate emitter flow sensor cable determines which connector hooks up to which emitter. See Figure Using the cable clamps provided, clamp the cables down to the two small studs in-between the sensors. Using the smaller clamp on the left stud and a larger clamp on the right stud. 11. Use cable ties to secure all cables and prevent them from interfering with the basket as it raises and lowers. 12. The Detector Cable inside the cleaner needs to the secured. Using one of the large cable clamps, secure the detector flow sensor cable to the stud on the left side of the mounting bracket See Figure Connect the cable to its respective sensors September

39 Ag Leader Technology Cotton Stripper Installation John Deere 7450/ Secure the cable as needed under the shield. IMPORTANT: Re-connect the wire connector blocks under the cab that was removed to prevent damage to the electrical system from welding or cutting with a plasma torch. Figure 40. With large cable clamp, clamp the cable using the stud provided. Final Inspection Installation is now complete. Do a walk around of the machine and complete the following: All cable connections have been made. Excess cable has been tied out of the way, so there is no potential interference. All tools and extra hardware have been removed from the machine. All cap screws and captive nuts are tight on the sensor mounts. September

40 Cotton Stripper Installation John Deere 7450/7455 Ag Leader Technology Operational Checkout Refer to the Display Items section in the Operation Section for instructions on how to display different items on the screen. Step-by-Step Procedure 1. Start engine. 2. Verify the monitor powers up/down properly. 2a. Turn the monitor power switch ON and verify the monitor powers up properly. NOTE: The monitor will power up, check a box for each sensor detected and display the harvest screen of four selected items. If sensors cannot be located, confirm the machine setup is correct by referring to Vehicle Setup in the Operator's Manual. If the problem continues refer to "Monitor Does Not Find Correct Number of Flow Sensors on Initial Power Up" in the Troubleshooting Section of this manual. 2b. Turn the monitor power switch OFF and verify the monitor powers down properly. NOTE: When the power switch is turned OFF the monitor will not immediately turn OFF. The screen will display "Now Archiving Data " "Monitor will automatically power down when complete". If the monitor does not power up/down as described, re-check the cable connections. 2c. With the ignition key off, and power switch "ON" on the monitor, turn the ignition switch ON. The monitor should automatically power up. Turn the ignition key off and the monitor should power down as described in the NOTE above. Check the switched power and full time power connections if power up/down is not as described. 3. Display Fan Speed on the screen. 3a. Verify that Fan RPM stays at zero with the Fan OFF. 3b. Engage the fan and verify the monitor measures fan RPM. It should increase as the engine speed increases all the way too full engine speed, if not re-check cable connections September

41 Ag Leader Technology Cotton Stripper Installation John Deere 7450/7455 NOTE: RPM may NOT be accurate, because fan pulses/revolution have not yet been set for your machine. 4. Display "Ground Speed" on the screen. Move the machine slowly to verify the monitor measures MPH at low speeds (below 1 mph). NOTE: MPH will NOT be accurate, because the monitor has not been calibrated to your machine. 5. Start the fan blower with the machine at rest and verify that the monitor reads 0.0 MPH. 6. Display "Head Height" on the screen. 6a. Lift the head and verify the head height number increases. Lower the head and verify the head height number decreases. (If it increases instead of decreases, or vice versa refer to the Operator's Manual to change the setup on the monitor.) 6b. Adjustment of chain length and bending of threaded arm may be required to get full range of the header height sensor. 7. Check for acceptable sensor signal strength. 7a. Press the MENU key, DIAG, and Signal Strength. Verify the signal strengths are not less than b. Adjust sensor mounting position to achieve acceptable signal strength. Refer to the Setup Section of the Operator s Manual to adjust the monitor to your machine. *** September

42

43 Ag Leader Technology Revision History Summary of Changes Revision 1 March 2002 Initial release of this document. Revision 2 September 2003 Changes to include the PFadvantage. September