Discrete direct acting 2 port solenoid valve (general purpose valve) AB31 AB41 Series NC (normally closed) type AB42 Series NO (normally open) type

Transcription

1 31414 Series iscrete direct acting port solenoid valve (general purpose valve) Series NC (normally closed) type 4 Series NO (normally open) type Port size: Rc1/8 to Rc1/ JIS symbol Common specifications 31/41: NC (normally closed) type Item Standard specifications Optional specifications Working fluid ir, low vacuum (1.33 x 10 Pa (abs)), water, kerosene, oil (50 mm /s or less) ot water Steam Working pressure differential range MPa Withstanding pressure (water) MPa 0 to 5 (refer to max. working pressure differential in individual specifications. ) 5 luid temperature (Note 1) C -10 to to to 4 4: NO (normally open) type mbient temperature eat proof class C -0 to 60-0 to 100 tmosphere Valve structure Place free of corrosive gas and explosive gas irect acting poppet structure Valve seat leakage cm 3 /min. (NR) 0. or less (air) 300 or less (air) Mounting attitude ree ody, sealant rass, nitrile rubber rass, ethylene propylene diene rubber rass, PT Note 1: No freezing Individual specifications Item Port size Orifice (mm) NC (normally closed) type Rc1/ Rc1/ NO (normally open) type Max. working pressure differential (MPa) ir Water, hot water, kerosene Oil (50 mm /s) Steam C C C C C C C (0.03) (0.03) 0.05 (0.03) *8 *8 * Max. working pressure (MPa) 5 5 (fluid; 1 for steam) Rated voltage 100 VC 50/60 z 110 VC 60 z 00 VC 50/60 z 0 VC 60 z 1 VC 4 VC 48 VC 100 VC 5 (fluid; 1 for steam) pparent power (V) Power consumption (W) olding Starting C 50 z 60 z 50 z 60 z 50/60 z / / (8.1) * / (14) *1: The model numbers above show the basic port size (Rc) and orifice diameter. Refer to ow to order for other combinations (e.g., for steam). *: The port size symbol is 01 for Rc1/8 (6), 0 for (8), 03 for (10) and 04 for Rc1/ (15). *3: Refer to C column for the max. working pressure differential of coil with diode. *4: The voltage fluctuation must be within ±10% of the rated voltage. *5: Power consumption of coil housing // is indicated. *6: When using with a low vacuum, vacuum the port side. *7: Power consumption of coil housing 6C/6/6/6 is indicated. *8: The C voltage of coil housing // and the max. working pressure differential of coil housing 6C/6/6 are indicated. C Weight (kg) () 11 5 (1) *5 () (7) *7 4 0 () ()

2 31414 Series Optional specifications (fluid temperature, ambient temperature, valve seat leakage) Sealant material luoro rubber thylene propylene diene rubber PT Coil (heat proof class) luid temperature (Note 1) C mbient temperature C Valve seat leakage cm 3 /min. (NR) -10 to 60-0 to to 90-0 to 100 (Note ) -10 to 60-0 to to 90-0 to 100 (Note ) -10 to 60-0 to to 4-0 to 100 (Note ) 0. or less (air) 300 or less (air) Note 1: No freezing Note : The range is -0 to 80 C when using the P terminal box with indicator light for the coil housing. N/ US/ / / low characteristics NC (normally closed) type NO (normally open) type Port size Rc1/8 Rc1/ Orifice (mm) *1: ffective sectional area S and sonic conductance C are converted as S 5.0 x C. *: Values shown in ( ) are for stainless steel body low characteristics C [dm 3 /(s bar)] b Cv flow factor ().1 (1.9) (.6) ().1 (1.9) (.6) 4.8 (4.6) 9.3 (8.1) ().1 (1.9) (.6) 4.8 (4.6) 3 9 (7) 8 (7) (0.38) 3 9 (7) 8 (7) (0.38) 0.9 (0.37) 0.36 (0.31) 3 9 (7) 8 (7) (0.38) 0.9 (0.37) (0) 4 (8) 0.8 (0.6) (0) 4 (8) 0.8 (0.6) (0.8) 1.88 () (0.6) (0.8) V W/ L P/ PK/ K or dry air xplosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems P// PJ CV/ CVS CP/ CP Medical analysis Custom order eneral purpose valve irect acting port solenoid valve

3 31414 Series ow to order NC (normally closed) type Port size: Orifice: ø3 The combinations indicated with in the above table are available. C ody/sealant combination: ody - brass, sealant - nitrile rubber Coil housing: rommet lead wire to I : lank J Rated voltage: 100 VC 50/60z, 110 VC 60z Note on model no. selection Note on C 0 Port size S C100V Orifice Coil housing Other options J Voltage Manual override (locking) Surge suppressor Mounting plate I Copper and PT free C ody/sealant combination *1 * *3 *4 *5 *6 *7 <xample 1 of model number> C100V : 31 <xample of model number> C100V : 41 Port size Orifice Port size: Orifice: ø3 C ody/sealant combination: ody - brass, sealant - nitrile rubber Coil housing: rommet lead wire Manual override (locking): Selected to : lank I Surge suppressor: Selected J Rated voltage: 100 VC 50/60z, 110 VC 60z Symbol escriptions Symbol escriptions Symbol ø ø ø3 ø3.5 ø4 ø5 ø7 ø10 C ody/sealant combination ody Sealant Treatment Remarks lank C V W J K P L M N R to J Std. rass or bronze Option Stainless steel Stainless steel rass Rc1/8 Rc1/ Nitrile rubber luoro rubber PT luoro rubber Nitrile rubber luoro rubber PT luoro rubber Nitrile rubber luoro rubber PT thylene propylene diene rubber Nitrile rubber luoro rubber PT thylene propylene diene rubber *1: *: *3: *4: *5: *6: *7: 1/8 1/4 3/8 1/ - Vacuum inspection - Vacuum inspection Oil free ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 4 C *) Medium vacuum ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 4 C *) Medium vacuum ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 4 C *) ot water (up to 90 C *) ir, water, low vacuum, kerosene (up to 60 C) ir, low vacuum, kerosene (up to 90 C *) Steam (up to 4 C *) ot water (up to 90 C *) Low pressure large flow rate Refer to page 36 in the Introduction for details on the material combinations. Refer to the following page for details on the coil housing, other options and voltage, etc. 1N N 3N 4N escriptions 1/8NPT 1/4NPT 3/8NPT 1/NPT Leave blank for standard. owever, to select options in to I, indicate 0 for C. When 4, 4M or 4N is selected for. The body for the low pressure large flow rate is bronze (standard) or stainless steel (optional). or option symbols V and W, vacuum is inspected at "leakage amount: 1.33 x 10-6 Pa m 3 /s or less". When C of the low pressure large flow rate is V or W, C voltage is not available. The ethylene propylene diene rubber seal combination (C P/R) cannot be used with air. (Compressed air contains oil, and ethylene propylene diene rubber is not oil-resistant. ) When C is C,, K, P, N or R, the coil housings 6C, 6, 6 and 6 cannot be selected.

4 31414 Series or to J, the combinations indicated with symbols can be manufactured. Note that if options to I are not required, no symbol is indicated. Coil housing Other options I J Rated voltage Cable gland Conduit escriptions (Marine cable gland) (Conduit pipe) escriptions -15a -15b -15c CTC19 1/ lank 3 3M 3N 3I 3J 4 4M 4N 5 5M 5N 5I 5J 6C lank 6C Std. Option rommet lead wire terminal box terminal box terminal box + small light (Pg11) Open frame type Open frame type (heat proof class ) (1/) (Pg11) Lead wire P terminal box (1/) P terminal box + light (1/) P terminal box (I5 or equivalent) (1/) (1/) P terminal box + light (I5 or equivalent) Lead wire P terminal box P terminal box + light Lead wire P terminal box (1/) (1/) Open (1/) frame type P terminal box + light (1/) (diode integrated) P terminal box (I5 or equivalent) (1/) P terminal box + light (I5 or equivalent) (1/) rommet lead wire 7W terminal box (1/) 7W terminal box (Pg11) 7W terminal box + small light (Pg11) 7W Manual override (locking) Mounting plate rommet lead wire 300 mm S Surge suppressor S S S Copper and PT free 100 VC, 00 VC 100 VC, 00 VC 1 VC, 4 VC, 48 VC, 100 VC 100 VC, 00 VC, 4 VC 100 VC, 00 VC 1 VC, 4 VC, 48 VC, 100 VC 100 VC, 00 VC, 1 VC, 4 VC, 100 VC 100 VC, 00 VC, 1 VC, 4 VC, 48 VC, 100 VC 100 VC, 00 VC, 1 VC, 4 VC, 100 VC 100 VC, 00 VC 100 VC, 00 VC 1 VC, 4 VC 4 VC Refer to the following precautions for to J. Conduit (CTC19) (1/) N/ US/ / / V W/ L P/ PK/ K or dry air xplosion proof V/ VL S/ SV NP/NP/ NVP M 3N 4M 4N 5M 5N 3I 3J 5I 5J terminal box Open frame type grommet lead wire 300 mm 4 (heat proof class ) 5 (diode integrated) Open frame P terminal box 4M, 4N (heat proof class ) 5M, 5N (diode integrated) Open frame P terminal box (I5 or equivalent) 5I, 5J (diode integrated) Refer to page 1 for coil selection. Note on model no. selection Note on *8: Leave blank for the standard coil housing. owever, to select options in to I, indicate 00 for. *9: 5, 5M, 5N, 5I and 5J are coils for which C power is converted to C with a diode. *10: C coil for steam is available for 41. Contact CK for more information. *11: 6C, 6, 6 or 6 can be selected for only 41. *1: The coil housings 6C, 6 and 6 are 1 VC and 4 VC dedicated. 6 is 4 VC dedicated. Note on to I *13: The manual override ( ) is not available for the low pressure large flow rate *14: When C is C,, K, N, V or W, the manual override ( ) is not available. *15: Select one among,,, and for. *16: The surge suppressor is an accessory for the lead wire coil. When selecting a coil with terminal box, the surge suppressor is mounted in the terminal box. *17: s standard, the surge suppressor is incorporated in the coil with diode and the 4 VC coil ( /6), so the surge suppressor symbol S cannot be selected. *: I is available only when C is L, M or R. *19: Tropicalization (rust-proof coating) is available as a measure against rust. Contact CK for more information. Note that the tropicalization is not available when the manual override option and the coil option 6C/6/6/6 are selected. Note on J *0: 100 VC coil is compatible with 100 VC 50/60 z and 110 VC 60 z, and 00 VC coil is compatible with 00 VC 50/60 z and 0 VC 60 z. Note that the coils 5/5M/5N/5I/5J can be used only with 100 VC 50/60 z or 00 VC 50/60 z. *1: or voltages other than above, consult with CK. *: The lead wire is available in the standard 300 mm length, and 500 mm, 1000 mm, 000 mm and 3000 mm lengths. Contact CK for more information. C/ MX/ Other.P. systems P// PJ CV/ CVS CP/ CP Medical analysis Custom order eneral purpose valve irect acting port solenoid valve

5 31414 Series ow to order NO (normally open) type L 3 C100V Port size Orifice <xample 1 of model number> C100V : 4 Port size: Orifice: ø C ody/sealant combination: Coil housing: to I : J Rated voltage: Coil housing Other options Manual override (locking) Surge suppressor Mounting plate C ody/sealant combination *1 * *3 *4 ody - brass, sealant - nitrile rubber rommet lead wire lank 100 VC 50/60z, 110 VC 60z J Voltage I Copper and PT free Symbol escriptions Port size 0 03 Orifice Std. Option to J ø ø ø3 ø3.5 ø4 ø5 ø7 C ody/sealant combination ody Sealant Treatment Remarks lank Nitrile rubber ir, water, low vacuum, kerosene (up to 60 C) luoro rubber - ir, low vacuum, kerosene (up to 90 C *) C PT Steam (up to 4 C *) V luoro rubber Vacuum inspection Medium vacuum Nitrile rubber ir, water, low vacuum, kerosene (up to 60 C) luoro rubber - ir, low vacuum, kerosene (up to 90 C *) PT Steam (up to 4 C *) W luoro rubber Vacuum inspection Medium vacuum Nitrile rubber ir, water, low vacuum, kerosene (up to 60 C) J luoro rubber ir, low vacuum, kerosene (up to 90 C *) K PT Steam (up to 4 C *) P thylene propylene diene rubber ot water (up to 90 C *) L Nitrile rubber Oil free ir, water, low vacuum, kerosene (up to 60 C) M luoro rubber ir, low vacuum, kerosene (up to 90 C *) N PT Steam (up to 4 C *) R thylene propylene diene rubber ot water (up to 90 C *) rass Stainless steel Stainless steel rass Symbol 3 escriptions 1/4 3/8 Symbol N 3N escriptions 1/4NPT 3/8NPT Refer to page 36 in the Introduction for details on the material combinations. Refer to the following page for details on the coil housing, other options and voltage, etc. <xample of model number> S-C100V : 4 Port size: Orifice: ø5 C ody/sealant combination: ody - brass, sealant - nitrile rubber Coil housing: rommet lead wire Manual override (locking): Selected : lank Surge suppressor: Selected J Rated voltage: 100 VC 50/60z, 110 VC 60z Note on model no. selection Note on C *1: Leave blank for standard. owever, to select options in to I, indicate 0 for C. *: When 4, 4M or 4N is selected for. *3: or option symbols V and W, vacuum is inspected at "leakage amount: 1.33 x 10-6 Pa m 3 /s or less". *4: The ethylene propylene diene rubber seal combination (C P/R) cannot be used with air. (Compressed air contains oil, and ethylene propylene diene rubber is not oil-resistant. )

6 31414 Series or to J, the combinations indicated with symbols can be manufactured. Note that if options to I are not required, no symbol is indicated. Coil housing Other options I J Rated voltage Cable gland Conduit escriptions (Marine cable gland) (Conduit pipe) escriptions -15a -15b -15c CTC19 1/ lank 3 3M 3N 3I 3J 4 4M 4N 5 5M 5N 5I 5J lank Std. Option rommet lead wire terminal box terminal box (1/) (Pg11) terminal box + small light (Pg11) Lead wire P terminal box (1/) Open frame type P terminal box + light (1/) P terminal box (I5 or equivalent) (1/) P terminal box + light (I5 or equivalent) (1/) Open Lead wire frame type P terminal box (1/) (heat proof class ) P terminal box + light (1/) Lead wire Open P terminal box (1/) frame type P terminal box + light (1/) (diode integrated) P terminal box (I5 or equivalent) (1/) P terminal box + light (I5 or equivalent) (1/) Manual override (locking) Mounting plate rommet lead wire 300 mm terminal box S S S Surge suppressor Copper and PT free 100 VC, 00 VC 100 VC, 00 VC 1 VC, 4 VC, 48 VC, 100 VC 100 VC, 00 VC, 4 VC 100 VC, 00 VC 1 VC, 4 VC, 48 VC, 100 VC 100 VC, 00 VC, 1 VC, 4 VC, 100 VC 100 VC, 00 VC, 1 VC, 4 VC, 48 VC, 100 VC 100 VC, 00 VC, 1 VC, 4 VC, 100 VC 100 VC, 00 VC 100 VC, 00 VC Refer to the following precautions for to J. Conduit (CTC19) (1/) N/ US/ / / V W/ L P/ PK/ K or dry air xplosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ M 3N 4M 4N 5M 5N 3I 3J 5I 5J Open frame type grommet lead wire 300 mm 4 (heat proof class ) 5 (diode integrated) Open frame P terminal box 4M, 4N (heat proof class ) 5M, 5N (diode integrated) Open frame P terminal box (I5 or equivalent) 5I, 5J (diode integrated) * Refer to page 1 for coil selection. Note on model no. selection Note on *5: Leave blank for the standard coil housing. owever, to select options in to I, indicate 00 for. *6: 5, 5M, 5N, 5I and 5J are coils for which C power is converted to C with a diode. Note on to I *7: When C is C,, K, N, V or M, the manual override ( ) is not available. *8: Select one among,,, and for. *9: The surge suppressor is an accessory for the lead wire coil. When selecting a coil with terminal box, the surge suppressor is mounted in the terminal box. *10: s standard, the surge suppressor is incorporated in the coil with diode and the 4 VC coil ( ), so the surge suppressor symbol S cannot be selected. *11: I is available only when C is L. *1: Tropicalization (rust-proof coating) is available as a measure against rust. Contact CK for more information. Note that the tropicalization is not available when the manual override option is selected. Note on J *13: 100 VC coil is compatible with 100 VC 50/60 z and 110 VC 60 z, and 00 VC coil is compatible with 00 VC 50/60 z and 0 VC 60 z. Note that the coils 5/5M/5N/5I/5J can be used only with 100 VC 50/60 z or 00 VC 50/60 z. *14: or voltages other than above, consult with CK. *15: The lead wire is available in the standard 300 mm length, and 500 mm, 1000 mm, 000 mm and 3000 mm lengths. Contact CK for more information. Other.P. systems P// PJ CV/ CVS CP/ CP Medical analysis Custom order eneral purpose valve irect acting port solenoid valve

7 31414 Series Internal structure and parts list 31 Series 41-0/03-1 to / No Parts name Material Coil Core assembly SUS405 or equivalent, 316L, 403 *1 Stainless steel Shading coil Cu (g for stainless steel body) Copper (silver for stainless steel body) Plunger SUS405 or equivalent Stainless steel No. Parts name Material 15 Plunger spring SUS304 Stainless steel NR (KM, PM, PT) NR: Nitrile rubber 6 O ring (size: S ) 37 Sealant NR (KM, PM, PT) ( KM: PM: luoro rubber PT: Tetrafluoroethylene thylene propylene resin ) diene rubber 48 ody C3771 or CC408 (SCS13) rass or bronze (stainless steel) *1: When the body/sealant combination symbol is other than blank or, or when the coil housing is 6C, 6, 6 or 6, the material is SUS405 or equivalent, 316L, 430. *: ( ) shows option. Note that PT is not available for

8 31414 Series Internal structure and parts list 4 N/ US/ / No. Parts name Material No. Parts name Material 1 Core assembly SUS405 or equivalent, 316L, 304 Stainless steel 6 O ring Coil 1 3 Plunger SUS405 or equivalent Stainless steel 7 Spring 4 Shading coil Cu (g for stainless steel body) Copper (silver for stainless steel body) 38 ody NR: Nitrile rubber (PM: thylene propylene diene rubber) 4 5 Sealant NR (KM, PM, PT) 9 NO valve (KM: luoro rubber) (PT: Tetrafluoroethylene resin) NR (KM, PM, PT) (size: S ) SUS304 C3771 (SUS303) POM (SUS303, P) NR: Nitrile rubber (PM: thylene propylene diene rubber) (KM: luoro rubber) (PT: Tetrafluoroethylene resin) Stainless steel rass (stainless steel) Option symbol : lank/0///l/v/w - polyacetal resin : Other than above - stainless steel, perfluoroalkoxy resin ( ) shows option. / V W/ L P/ PK/ K or dry air xplosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems P// PJ CV/ CVS CP/ CP Medical analysis Custom order eneral purpose valve irect acting port solenoid valve

9 31414 Series imensions: 31 Series rommet lead wire type 31-01/0-1 to 6-* lank Note 1: The 31 Series is an open when energized type port solenoid valve. The body and sealant materials are combined according to the working fluid, and the orifice and pressure are selected according to the relation of the required flow rate and pressure. The coil specifications are determined according to the fluid temperature and ambient conditions, allowing the optimum valve to be selected. Note : The dimensions are the same for the or NPT thread port size M5 depth 8 8 Rc1/8 (01) (0) CK * Lead wire length 300 mm to 6-C -0-1 to 6-C

10 31414 Series Optional dimensions: 31 Series terminal box 31-01/0-1 to 6-* C 7.5 * Refer to the grommet lead wire type dimensions on the left page for common dimensions. Open frame lead wire type 31-01/0-1 to 6-* N/ US/ / / 39 (41) 75 5 V W/ Voltage C (//) C (//) imensions shown in ( ) are for 1/. C (50) 5 (5) L Open frame type + P terminal box 31-01/0-1 to 6-* 3 M 4M 5 N 4N I J Stainless steel body 31-01/0-1 to 6- ///R/W/L/M/N lank ø Open frame type + conduit 31-01/0-1 to 6-* (56) Manual override (locking) 31-01/0-1 to 6-*** igure shows the brass body. Manual override (ø37.5) 38 CTC19 (1/) imensions shown in ( ) are for 1/. imensions shown in ( ) are for stainless steel body. P/ PK/ K or dry air xplosion proof V/ VL S/ SV NP/NP/ NVP C/ MX/ Other.P. systems P// PJ CV/ CVS CP/ CP Medical analysis Custom order Mounting plate 31-01/0-1 to 6-*** eneral purpose valve irect acting port solenoid valve 8 4-ø5.5 -ø6 Mounting plate No

11 31414 Series imensions: 41 Series rommet lead wire type 41-0/03-1 to 7-* lank 6C C -M5 depth 8 (0) (03) CK * Lead wire length 300 mm to 6-C C to 7-C to 6-6C-C C-C to 7-6C-C C rommet lead wire type 41-03/04-8-* lank 6C CK C C C-C C-C M5 epth 8 Note 1: Note : (03) -Rc1/ (04) This 41 Series, port solenoid valve, open when energized, is designed to meet the customer's requirement according to working fluid, body and seal materials, relation between flow rate and the required pressure (converted to orifice diameter and pressure), and ambient temperature and conditions (converted to coil specifications). The dimensions are the same for the or NPT thread port size.

12 31414 Series Optional dimensions: 41 Series terminal box 41-0/03/04-1 to 8-* * Refer to the grommet lead wire type dimensions on the left page for common dimensions. Open frame lead wire type 41-0/03/04-1 to 8-* N/ US/ / 39 (41) I / V W/ imensions shown in ( ) are for 1/. Voltage I C (//) C (//) C (6/6/6) (53.5) 54.5 (54) 56.5 (56) Open frame type + P terminal box 41-0/03/04-1 to 8-* 3 M 4M 5 N 4N I 103 J Stainless steel body 41-0/03/04-1 to 8- //R/W/L/M/N/ to 6-** ** to 7-** 41-03/04-8-** Open frame type + conduit 41-0/03/04-1 to 8-* (60) imensions shown in ( ) are for 1/. CTC19 (1/) L P/ PK/ K or dry air xplosion proof V/ VL S/ SV NP/NP/ NVP C/ Manual override (locking) 41-0/03-1 to 7-*** igure shows the brass body. MX/ Other.P. systems to 6-C C to 7-C C C Mounting plate 41-0/03/04-1 to 8-*** 6 (70) 50 (58) () 30 8 C C ø ø * *1: The max. dimension is ø54. 4-ø5.5 -ø6 imensions shown in ( ) are for mounting plate No.. Note: No manual override is available for 41-03/04-8. K to 6-*** *** to 7-*** 36 (ø37.5) 40 (ø45.0) imensions shown in ( ) are for stainless steel body. Mounting plate No Mounting plate No Manual override K pplicable model 41-0/03-1 to 7 Series Stainless steel body to 6- ///L/M/N/R/W 41-03/04-8 Series Stainless steel body ///L/M/N/R/W to 7- ///L/M/N/R/W P// PJ CV/ CVS CP/ CP Medical analysis Custom order eneral purpose valve irect acting port solenoid valve

13 31414 Series imensions: 4 Series rommet lead wire type 4-0/03-1 to <Reference> port direct acting valve, closed when energized, is open when de-energized. This type is commonly used to be continuously energized. The dimensions are the same for the or NPT thread port size. Note 1: The dimensions are the same for the or NPT thread port size. C (0) (03) -M5 depth 8 CK * Lead wire length 300 mm to to 7 C

14 31414 Series Optional dimensions: 4 Series terminal box 4-0/03-1 to 7-* 7.5 * Refer to the grommet lead wire type dimensions on the left page for common dimensions. Open frame lead wire type 4-0/03-1 to 7-* N/ US/ / / 39 (41) 31 V W/ Voltage C C imensions shown in ( ) are for 1/ (53.5) (60) to to L Open frame type + P terminal box 4-0/03-1 to 7-* 3 M 4M 5 N 4N I J Open frame type + conduit 4-0/03-1 to 7-* (60) imensions shown in ( ) are for 1/. CTC19 (1/) P/ PK/ K or dry air xplosion proof V/ VL S/ SV NP/NP/ NVP Stainless steel body 4-0/03-1 to 7- ///R/W/L/M/N Manual override (locking) 4-0/03-1 to 7-*** C/ MX/ to to 7 Mounting plate 4-0/03-1 to 7-*** 6 (70) 50 (58) 30 8 C C ø ø ø ø5.5 -ø imensions shown in ( ) are for mounting plate No.. (13) Code Mounting plate No Mounting plate No Manual override pplicable model 4-0/03-1 to 7 Series Stainless steel body to 6- ///L/M/N/R/W Stainless steel body ///L/M/N/R/W to 7- ///L/M/N/R/W Other.P. systems P// PJ CV/ CVS CP/ CP Medical analysis Custom order eneral purpose valve irect acting port solenoid valve