Normally-open. Normally-open

Transcription

1 Series BMF 07 Series BMF 07 BMF 07 PNP Normally-open BMF 07K-PS-C--S49- BMF 07K-PS-C-- Non-contact, wear-free piston sensing Insensitive to contamination Piston sensed through the cylinder wall Can be installed on any cylinder size using the corresponding bracket Wiring diagrams PNP/ NPN/ PNP/ NPN/ NPN Normally-open Rated operating field strength I H n I Assured operating field strength I H a I Hysteresis of I H n I Temperature drift of turn-on point of I H n I Supply voltage U B Voltage drop U d Rated insulation voltage U i Rated operational current I e No-load supply current I 0 max. Off-state current I r Protected against polarity reversal Short circuit protected Load capacity Ambient temperature range T a Utilization category Degree of protection per IEC 059 Housing material Connection No. of wires conductor cross section Approval Recommended 0. %/ C.1 V 0 ma LCP with BKS-B %/ C.1 V 0 ma LCP 0.14 mm² Please add the length to the ordering code for sensors with! PU-0, PU-05 = PUR, length m or 5 m Brackets for with tie rod Please add the length to the ordering code for sensors with and! 00,, 00,5 = PUR, length 0. m or 0.5 m Connector orientation with DUO rail without tie rod/rail Profile cylinder with trapezoidal rail Without brackets with T-slot/ trapezoidal slot useable without bracket in cylinder with T-slot e. g. Festo ADVU, DRQ, DGP.1

2 Series BMF 1, BMF BMF 1 BMF 1 BMF BMF BMF switchpoint switchpoint switchpoint suitable for AC weld environments BMF 1K-PS-C--S49 BMF 1K-PS-C-- BMF M-PS-C--S49 BMF M-PS-C--S 4 BMF M-PS-W--S 4 BMF 1K-NS-C--S49 BMF 1K-NS-C-- BMF M-NS-C--S49 BMF M-NS-C--S 4 0. %/ C 0. %/ C 0. %/ C 0. %/ C 0. %/ C.1 V 0 ma PBT (fiberglass reinforced) BKS-B 48/BKS-B 49.1 V 0 ma PBT (fiberglass reinforced) 0.14 mm².1 V 0 ma Al BKS-B 48/BKS-B 49.1 V 0 ma Al BKS-B 19/BKS-B 0 4 V 0 ma 0.15 µf Al BKS-B 19/BKS-B 0 Brackets page Connectors selection guide page.0... BMF 1-HW-8 BMF 1-HW-10 BMF 1-HW-8 BMF 1-HW-10 BMF -HW-1 BMF -HW-1 BMF -HW-1 BMF 1-HW-8 BMF 1-HW-8 BMF -HW-1 BMF -HW-1 BMF -HW-1 BMF 1-HW-11 BMF 1-HW-10 BMF 1-HW-11 BMF 1-HW-10 Connectors... page.... BMF -HW-1 (Mecman) BMF -HW-14 (Bosch) BMF -HW-1 (Mecman) BMF -HW-14 (Bosch) BMF -HW-1 (Mecman) BMF -HW-14 (Bosch) useable without bracket on cylinders with 0 - or 90 -trapezoidal slot e. g. Festo, Bosch, Martonair.1

3 Brackets for BMF 1 BMF 1-HW-8 tie rod diameter up to.5 mm pneumatic cylinder with DUO rail (Festo), BMF 1-HW-10/BMF 1-HW-10-E tie rod diameter up to 17 mm for pneumatic cylinder with integral tie rod (profile) profile width up to 17 mm BMF 1-HW-10-E: stainless steel BMF 1-HW-11 for pneumatic cylinder without tie rod/rail piston diameter mm bracket for use only with tube cuff please order tube cuff separately (see page.15)..14

4 Brackets for BMF BMF -HW-1 for pneumatic cylinder with trapezoidal rail (Rexroth-Mecman) BMF -HW-1 tie rod diameter max. 11 mm BMF -HW-14 for pneumatic cylinder with trapezoidal rail (Bosch) type: /51/5/5/54/55 tie rod diameter up to 17 mm for pneumatic cylinder with integral tie rod (profile) profile width up to 17 mm BMF -HW-1 tie rod diameter up to.5 mm pneumatic cylinder with DUO rail (Festo), BMF Tube cuff size stainless steel for pneumatic cylinder without tie rod/rail piston diameter mm Piston Æ Tube cuff size for BMF 1-HW-11 Tube cuff size for BMF 8, , Tube cuff size _ please order separately.15

5 Cylindrical Housings Æ.5 mm, Æ 10 mm, M8, M1 BMF 07M Æ.5 mm BMF 07M Æ.5 mm BMF 08M M8 1 BMF 1M M1 1 BMF 10E for foods industry bracket BMF 10E-HW-19 Æ 10 mm stainless steel BMF 07M-PS-D--S 4- BMF 07M-PS-C--KPU- BMF 08M-PS-C--KPU- BMF 1M-PS-D--S 4 BMF 10E-PS-D--SA 1-S49 BMF 07M-NS-C--KPU- BMF 08M-NS-C--KPU- BMF 1M-NS-D--S 4 0. %/ o C 0. %/ o C 0. %/ o C 0. %/ o C 0. %/ o C.5 V 1 ma with BKS-B 19.5 V ma 0.14 mm².1 V ma 0.14 mm².5 V 1 ma BKS-B 19/BKS-B 0.5 V 1 ma stainless steel BKS-B 48/BKS-B 49 Connectors selection guide page.0... Operating distance magnet sensor Magnet type Samarium-Cobalt Hard ferrite Strontium-Ferrite Bracket BMF 10E-HW-19 (please order separately) Ordering code Housing size Height Assured operating distance S a Hysteresis mm mm 8 mm 8 mm Æ 10 mm 10 mm 15 mm mm Æ 4 mm 5 mm 5 mm mm Within the operating zone scheduled, a secure switch is guaranted. The operating zones have been determined in measuring series and help to choose a magnet suitable. Piston-Æ 8, 10, 1 1, 0, Tube cuff size Tube cuff size _ please order separately Connectors, clamps... page

6 Installation Notes Mounting distances The response travel of a magnetic field sensitive sensor is virtually independent of the field strength of typical piston magnets. Still the sensor does not exhibit false switching. When using more than one of the magnetic field switches, the BMF sensors can be mounted directly next to or beside each other. Adjustment and installation 1. Set piston to end of travel.. Slide sensor (with power on) until the output turns on (LED on). Mark front edge of sensor on cylinder.. Continue to slide the sensor until the output is off (LED off). 4. Slide sensor back to nd turn-on point. Mark front edge of sensor on cylinder. 5. Fasten sensor down with front edge is between the two marked points..18