Moddit. How to Install Raceseng S1/S2 Pulley Kit on Subaru BRZ
|
|
- Randall Powers
- 5 years ago
- Views:
Transcription
1 Moddit How to Install Raceseng S1/S2 Pulley Kit on Subaru BRZ A quick and simple write up on the Raceseng S1/S2 Pulley Kit install on our Subaru BRZ. Written By: Ruthie Page 1 of 11
2 INTRODUCTION This write up will be a guide to the brave ones who decide they want to remove and install pulleys on their Subaru BRZ or Scion FR-S. The un-sprung difference in weight of the pulleys make a noticeable difference for the engine's responsiveness. It is definitely an affordable and fun mod. Note: Since we are installing the S2 kit, we had to remove the two idlers. IF you are installing the S1 kit, you DO NOT need to remove the two idlers as they do not come in the kit. TOOLS: 1/2 Breaker Bar (1) 12mm, 14mm, 17mm, and 19mm sockets and combination wrenches (1) 22 mm Socket (1) 24 mm Socket (1) Electric Impact Gun (1) Page 2 of 11
3 Step 1 How to Remove the Stock Pulleys from a Subaru BRZ Place the transmission gear into the 6th gear position and apply the e- brake. If it's an automatic, please check the factory service manual for the proper locking procedures. Refer to our BRZ Intake Removal Guide to remove the intake for an easier install. Also, before taking any pulley's off, do not forget to take a picture or draw out the orientation of the belts, so they can be re installed properly. Step 2 Use a 22mm socket and a 1/2 inch drive with a breaker bar to loosen the crankshaft bolt. You may need to use 100 ft/lbs to get it loose. The engine will have a slight give, but just pull on it and it will eventually loosen Page 3 of 11
4 Step 3 While the serpentine belt is still on the pulleys, use a 10mm socket with a ratchet to loosen the water pump pulley. There are 3 bolts. Do not lose these bolts, as they are essential to the drive-ability of your vehicle. Step 4 With a 10mm socket or wrench, remove the alternator cover before attempting to remove the alternator pulley bolt. Once removed, use a 24mm socket and impact gun to now remove the loosen the alternator pulley bolt. It is advised to use an Impact Gun for the alternator pulley removal because there is no other way to hold the pulley from spinning. The torque from the impact gun will remove the nut from the alternator without spinning it Page 4 of 11
5 Step 5 With a 14mm socket and wrench, slowly turn the tension pulley clockwise until the belt is removable. With the 14mm socket, loosen the bolts to both idler pulleys. Step 6 Once the pulley's are loose, and all the bolts are loose, you can go ahead and slip the belt off of the pulleys. Although the belt is loose, do not remove it, as you do not want to forget the orientation of the belts Page 5 of 11
6 Step 7 With all the pulleys loose, now remove each one: the crank pulley, water pump pulley, alternator pulley and both idler pulleys. Note: When removing the crank pulley, do not allow the crank pulley hub to back out of the timing cover. If this occurs, you will need to align the internal keyway with the crankshaft before assembly. Step 8 Dont forget to keep all of the hardware together, as you DO NOT want to lose any of them. These chubby pulleys are ready to be stored, and replaced with the lighter aftermarket ones Page 6 of 11
7 Step 9 How to Install Raceseng S1/S2 Pulley Kit on Subaru BRZ The removal of the stock idlers is not necessary for the S1 kit. Since we are installing the S2 kit, we have to remove the stock idler pulleys. Carefully place everything in one place to keep the pulleys nice and neat. Depending on how you keep your hardware, its always good to organize them as well. Disconnect the battery for your safety. Step 10 Set the water pump pulley on the water pump and make sure the orientation is correct. Use the blue thread locker on the threads of the bolt to keep it from coming loose. With the water pump pulley on, thread in the bolts, but do not completely tighten them yet Page 7 of 11
8 Step 11 Take the o-ring from the factory pulley and install it on to the crank pulley. Then line up the crank pulley to the keyway and hand tighten the bolt with the thread locker on the threads into place. Step 12 Now install the alternator pulley but do not thread the nut on yet. Put blue thread locker on the threads of the alternator and thread on the nut for the pulley Page 8 of 11
9 Step 13 If you ordered the S2 kit, you will now install the idler pulleys. Put the blue thread locker on the bolt for the idler pulley Then line up the holes and put the bolt through them. There are two idler pulleys that need to be installed, Repeat the process for the 2nd one. Step 14 Install the belts in the order your removed them, making sure to leave the alternator belt last to slip over Page 9 of 11
10 Step 15 Tighten and torque all the pulleys to the recommended specs. Note: For the crank pulley, torque to 94 ft/lbs. Place the vehicle in Neutral gear position and rotate the crank to make sure the belts are seated properly before turning on the vehicle. Reconnect the battery and start the car with the E-brake on and in neutral. Step 16 The difference in weight is 5.05 lbs. Imagine spinning something that is 7 lbs vs. 2 lbs. The difference is what the engine has been released of and can now spin a lot easier and quicker. The car should be more responsive and perkier. A whole loads of Fun. The installation of the light weight pulleys on the motor will definitely perk them up a bit. Just be sure that everything is torqued down, that way the engine runs smooth and well Page 10 of 11
11 This document was last generated on :53:45 AM Page 11 of 11
Moddit. How to Install the HKS Header W/ Cat on a Subaru BRZ
Moddit How to Install the HKS Header W/ Cat on a Subaru BRZ This full write up is a step by step process on the removal of the stock exhaust components, to the install of the HKS header with Cat. Written
More informationHow to Install a Tanabe Medalion Concept G Exahust on a Subaru BRZ
Moddit How to Install a Tanabe Medalion Concept G Exahust on a Subaru BRZ Written By: Terence Chang 2019 www.moddit.com/ Page 1 of 11 TOOLS: Metric Socket Set- 10mm,12mm,14mm,17mm (1) Metric Combination
More informationModdit. How to Install a Tomei Front Pipe on a Subaru BRZ. This write up will show how to install a front pipe on a BRZ. Written By: Dung Nguyen
Moddit How to Install a Tomei Front Pipe on a Subaru BRZ This write up will show how to install a front pipe on a BRZ. Written By: Dung Nguyen 2017 www.moddit.com Page 1 of 10 INTRODUCTION With the availability
More informationSTEP 1 Disconnect the negative terminal from both batteries.
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationFORD COBRA JET SPRING INSTALLATION
FORD COBRA JET SPRING INSTALLATION Tools Needed: 1. Floor jack with rubber padding on lift point or vehicle lift 2. Jack stands (2) 3. Socket sizes 13/16, 3/4, 15mm, 8mm 4. Pliers 5. Breaker bar, ratchet
More informationIncluded parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Brackets/Hardware
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports
More informationModdit. How to install Stance Subframe Collars into a. This guide will quickly go over how to install subframe collars for your Subaru BRZ.
Moddit How to install Stance Subframe Collars into a BRZ This guide will quickly go over how to install subframe collars for your Subaru BRZ. Written By: Jesus 2017 www.moddit.com Page 1 of 9 PARTS: Stance
More informationEurocompulsion Camshaft Installation
Eurocompulsion Camshaft Installation Introduction, please read. The purpose of this article is too assist our customers with installation of a performance camshaft in the Fiat Multiair 1.4 Turbo. The operation
More informationFord Focus Zetec SVT Timing Belt
2000-2004 Ford Focus Zetec SVT Timing Belt Replacement This guide will show you how to replace the timing belt on the 2.0L DOHC Zetec with VCT on a 2002 Ford Focus SVT. This is an interference motor. Written
More informationDistributorless Ignition System (DIS) Application: LLV Part Number: (E) or (A) Time Required: Approx.
www.teamwbi.com / e-mail: mip@teamwbi.com / 800-842-7285 Distributorless Ignition System (DIS) Application: 1987 1993 LLV Part Number: 01-5332 (E) or 01-5333 (A) Time Required: Approx. 1 hour Quantity
More informationModdit. How to Install Stance Coilovers on a Subaru
Moddit How to Install Stance Coilovers on a Subaru BRZ Let's get LOW (and maybe lighter and stiffer suspension)! In this article, we will install Stance ST- ZN6-XS Coilovers on the FRSport Subaru BRZ.
More informationCOBB CAMSHAFTS INSTALLATION Impreza RS/TS
4673 South Cherry St. Salt Lake City, UT 84213 USA +1 801-713-0035 COBB CAMSHAFTS INSTALLATION 99-01 Impreza RS/TS Congratulations on your purchase of Cobb Camshafts. The following instructions should
More informationBD Venom Dual Fuel F O R D 6. 7 L P O W E R S T R O K E Installation Instructions
U 30 January 2017 (1050470) Venom Dual Fuel Kit (I-00390) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Venom Dual Fuel 2 0 1 1-2 0 1 4 F O R D 6. 7 L P O W E R S T R O K E Installation
More informationBD Venom Dual Fuel F O R D 6. 7 L P O W E R S T R O K E Installation Instructions
U 21 March 2017 (1050470) Venom Dual Fuel Kit (I-00390) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Venom Dual Fuel 2 0 1 1-2 0 1 6 F O R D 6. 7 L P O W E R S T R O K E Installation
More informationInstallation Instructions for Scion FR-S, Toyota FT86, or Subaru BRZ PN-11839, 11937
Installation Instructions for Scion FR-S, Toyota FT86, or Subaru BRZ PN-11839, 11937 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the
More informationREMOVAL AND REPLACEMENT
2002 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair REMOVAL AND REPLACEMENT https://my.alldata.com/repair/#/repair/article/36847/component/64/itype/401/nonstandard/
More information6. Remove OEM bolts from engine at locations A, B, and C. Lay the wiring off to the side.
700359 DewEze Clutch Pump Kit #700359 Ford 5.4L, 6.8L w/ and w/o A/C AA mount 1999- INSTALLATION INSTRUCTIONS 1. Disconnect the battery. 2. Drain the radiator. 3. Remove the air cleaner assembly. 4. Remove
More informationTORQUE SPECIFICATIONS
2000 Suzuki Truck Grand Vitara LTD JLS 2WD V6-2.5L Vehicle > Engine, Cooling and Exhaust > Engine > Specifications > Mechanical TORQUE SPECIFICATIONS Engine Torque Specifications TORQUE COMPONENT TIGHTENING
More informationModels Affected: Visions with Propane Engines CORRECTIVE ACTION ---- PROCEDURE
Propane Belt Squeal Models Affected: Visions with Propane Engines ISSUE Front End Accessory Drive (FEAD) Belt chirping/squealing caused by improper fore-aft crankshaft pulley positioning. CORRECTIVE ACTION
More informationTiming belt change. Timing belt change
Timing belt change Put 2 new Gates T275 timing belts on today. Tensioner drilled smooth and tight with less than 16,000 miles on her decided not to change the tensioners just the belts. You'll need some
More informationLowering Spring Installation on a Mustang GT
Lowering Spring Installation on a 99-04 Mustang GT This installation is very the same installation that many of the 79-04 Mustangs excluding Cobra require. Time to install: 2-3 hours to do alone with a
More information2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1. Timing Belt: Service and Repair
2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page 1 Timing Belt: Service and Repair 2001 Mitsubishi Truck Montero LTD 4WD V6-3.5L SOHC Copyright 2006, ALLDATA 8.80 Page
More informationTiming Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L
Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air
More informationLong Tube Header Installation PNs , 17276
Long Tube Header Installation PNs - 17260, 17276 ***** Please compare the parts in the box with the bill of materials provided ***** to assure that you have all the parts necessary for this installation.
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn
More informationPORSCHE V r Valve Timing Instructions. Copyright 2009 Written by Mike Frye Edited my Adam G.
PORSCHE 928 32V r Valve Timing Instructions Copyright 2009 Written by Mike Frye Edited my Adam G. Sections: Overview.3 Disclaimer/warnings/things to watch for 4 Terms and naming conventions used in this
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationMax IV Rear Axle Replacement For models after Serial Number and all rear splined axle replacements.
Max IV Rear Axle Replacement For models after Serial Number 19089 and all rear splined axle replacements. 10/8/03 Max IV Snap Ring Rear Axle replacement.doc Tools required: 9/16 Wrench 6 Extension Steel
More informationWood Grain Warrior Line Incognito hidden winch bumper installation instructions Lexus GX470
Wood Grain Warrior Line Incognito hidden winch bumper installation instructions 2003-2009 Lexus GX470 Version 1.0-2016 Thank you for purchasing the Southern Style OffRoad Wood Grain Warrior Line Lexus
More informationAir Commander Part No
EASYSTREET Air Commander Part No. 26901 www.airliftcompany.com MN-508 (05504) NPR 5129 Please read these instructions completely before proceeding with installation Front View Side View Hardware Item P/N
More informationInstruction Sheet. Kit Numbers: , , & CRANK PULLEY KIT DISASSEMBLY. Package Contents
Instruction Sheet Kit Numbers: 5600, 5700, 5800 & 5300 CRANK PULLEY KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand, and follow all safety
More informationSR Performance Billet Aluminum Adjustable Motor Mounts (05-14 GT)
SR Performance Billet Aluminum Adjustable Motor Mounts (05-14 GT) Tools Needed 1. Engine hoist and chains (only for Hoist method) 2. jack with a 2x4 piece of wood (only for jack method) 3. Wrench 4. Extensions
More informationVersion 2.0 Supercharger Pulley +5%, 0%, 15%, 17% and 19% Reductions
Version 2.0 +5%, 0%, 15%, 17% and 19% Reductions 07232008 Thank you for purchasing the ALTA Performance supercharger pulley. Persons experienced in the proper operation of MINI engine systems and components
More informationHow To: Lift the Truck Using Shackles and Torsion Bars A CFans Members Mod Project by gawillet
How To: Lift the Truck Using Shackles and Torsion Bars A CFans Members Mod Project by gawillet Skill Level: Moderate Disclaimer: Please use caution and seek professional assistance when necessary. ColoradoFans.com,
More informationSteeda S197 Mustang Whipple Supercharger Drive
Steeda S197 Mustang Whipple Supercharger Drive Parts List Qty. Description 1 Whipple supercharger snout 1 Whipple snout collar 1 10-rib supercharger pulley 1 10-rib crank pulley 1 10-rib belt tensioner
More informationThe Driveshaft Shop One Piece Aluminum Driveshaft Install for GT/BOSS
The Driveshaft Shop One Piece Aluminum Driveshaft Install for 2011-14 GT/BOSS Tools and Equipment needed: Install time: approximately 2-3 hours Ratcheting socket wrench socket extensions 1/2 drive breaker
More informationTiming Belt Replacement
2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing
More informationModdit. How to Install an OS Giken Differential into a
Moddit How to Install an OS Giken Differential into a Subaru BRZ This guide goes over the steps necessary to remove and install the OS Giken Limited Slip Differential into a Subaru BRZ. This guide may
More information2010 CAMARO COG DRIVE UPGRADE Installation Instructions
2010 CAMARO COG DRIVE UPGRADE Installation Instructions 2010 CAMARO SS (LS3 & L99) P/N: 4GE118-010, 4GE118-020, 4GE118-030 ENGINEERING, LLC 1650 Pacific Avenue, Channel Islands, CA 93033-9901 Phone 805
More informationSlingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
More informationAamir_bt The legend..
Aamir_bt The legend.. How to do timing on a 4XE1-W (DOHC) engine. well i decided to to a write up for DOHC timing since there was only the SOHC written up, and i had to do a timing belt on my stylus anyways,
More informationBill of Materials: Please take time to read and understand these installation instructions.
Please take time to read and understand these installation instructions. CORSA recommends that installation of this system be performed by a qualified service center or professional muffler installer who
More informationRear Parking Brake Cable (93 Cobra)
Rear Parking Brake Cable (93 Cobra) Materials in the box: Brake Cable Tools Needed: One jack and four jack stands. One socket wrench with a 12mm, 13mm ( ½ inch, 12 point DEEP WALL DO NOT FORGET THIS) and
More informationM52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit
Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure
More information1 of 17 2/19/ :10 AM TIMING BELT
1 of 17 2/19/2012 11:10 AM TIMING BELT 2 of 17 2/19/2012 11:10 AM INSTALLATION SPROCKET 1) Install right-hand belt cover No.2. 3 of 17 2/19/2012 11:10 AM 2) Install left-hand belt cover No.2. 3) Install
More information2015 Corvette Supercharger System Instructions
2015 Corvette Supercharger System Instructions These instructions are meant to serve as a guide to the installation of the ECS 2015 Corvette Supercharging system. Please be sure to use all safety equipment
More informationPORSCHE V TO 32V CAM GEAR CONVERSION INSTRUCTIONS. For all 16V engines: USA 78-84, Euro
PORSCHE 928 16V TO 32V CAM GEAR CONVERSION INSTRUCTIONS For all 16V engines: USA 78-84, Euro 77-86 2.0 cams@mrtubby.net Required parts not included in kit (2) HTD 32V cam gears - sprocket 928.105.530.01
More informationBEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta).
BEW engine timing belt replacement procedure from MOGolf (as demonstrated on a 2004 Jetta). Based on the procedure published by Volkswagen, but modified for the "average" shadetree mechanic. Some special
More informationInstallation Instructions
Part Number: 10.109.01.109 Description: AUTOTECH Sport 270 Hydraulic Camshaft Note: If the job seems to be beyond your abilities, we recommend that you refer this installation to a qualified mechanic.
More informationCP3 Retrofit Pump Install:
CP3 Retrofit Pump Install: 2A 4 2 5 3 6 1.) Clean this area very well. No dirt = No troubles!!!!! Lay lots of Rags under and around the pumps, alternator and belts!!!!! This will save dropped tools, parts,
More informationVW & Audi TDI CR140 ECO KIT Installation Guide
VW & Audi TDI CR140 ECO KIT Installation Guide This guide is to help you install your new Rawtek DPF, EGR & Adblue Delete Exhaust ECO Kit on your (2009-2014) VW / Audi with 2.0l CR140 Diesel Engine. Note:
More informationDrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationALTERNATOR REPAIR FOR BMW 645 CI. E64 ENGINE N62 BY KEVIN BOWEN 6/9/2013
ALTERNATOR REPAIR FOR BMW 645 CI. E64 ENGINE N62 BY KEVIN BOWEN 6/9/2013 Level of difficulty: If you follow these directions, moderate, hardest part is aligning the alternator back for repositioning. Length
More informationv Porsche 928
1985-86 32v Porsche 928 Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger kit at this price relies
More information60-72 Chevrolet C10 Power Rack & Pinion Kit Instructions # , , &
60-72 Chevrolet C10 Power Rack & Pinion Kit Instructions # 8011740-01, 8011900-01, & 8011920-01 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer
More informationThis Package should contain: 1. Two CorkSport Assembled Front Adjustable Struts 2. Two CorkSport Rear Adjustable Shocks 3. Two CorkSport Rear Springs
1 2 3 This Package should contain: 1. Two CorkSport Assembled Front Adjustable Struts 2. Two CorkSport Rear Adjustable Shocks 3. Two CorkSport Rear Springs Thank you for purchasing the CorkSport Mazda
More information2. Timing Belt SERVICE PROCEDURE A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER. 1) Remove A/C belt. (With A/C model)
SERVICE PROCEDURE [W2A1] 2-3a A: REMOVAL 1. CRANKSHAFT PULLEY AND BELT COVER B2M2583A (1) Front side V-belt (2) Rear side V-belt (With A/C model) (3) Crankshaft pulley bolt (4) Crankshaft Pulley (5) Belt
More informationScion FR-S ZN6. GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N #
TURBO KIT Scion FR-S ZN6 Subaru BRZ ZC6 GTX2867R Gen2 (Internal Wastegate) Installation Instructions GPP P/N # 11518000 Vehicle Type Chassis Code Engine Code Transmission Model Year Scion FR-S DBA-ZN6
More informationSpecial Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
More informationAdjusting the PRS Z-Axis Bearings
888-680-4466 ShopBotTools.com Adjusting the PRS Z-Axis Bearings Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Introduction This document describes how to adjust the
More informationPage 1 of 8 2005 Volvo S40 2.4L Eng Base TIMING BELT REPLACEMENT - 2.4L & 2.5L TURBO, 5-CYLINDER REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft
More informationCHEVY SILVERADO CREW CAB RX3 Includes models equipped with DEF tank
2007-2017 CHEVY SILVERADO 1500-3500 CREW CAB RX3 Includes models equipped with DEF tank HARDWARE INCLUDED RECOMMENDED TOOLS 1 Passenger Side Front Support Plate 13mm Wrench 1 8-1.25 x 40mm Hex Bolt 13mm
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationHURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog # by Hurst Performance
FORM 159 0205 07/15 HURST COMP/PLUS SHIFTER 2015 Ford Mustang (Getrag MT82 six-speed manual transmission) Catalog #391 0205 2015 by Hurst Performance Thank you for purchasing the Hurst Comp/Plus Shifter.
More informationPorsche 928 with 16v LH-Jetronic Fuel System
Porsche 928 with 16v LH-Jetronic Fuel System Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this manual and give copies to your friends. Our ability to bring you this supercharger
More informationJaguar Update. Adjustable Reaction Plate
Jaguar Update Adjustable Reaction Plate Home January 7, 2008 I recently installed an adjustable reaction plate from CoolCat Express Corp. I've included some notes from that experience. I'm not affiliated
More informationCOBB SPORT SPRINGS
915760 - COBB SPORT SPRINGS 2008-2013 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2008-2013 Subaru WRX/STi. The following instructions will assist you through your
More informationCONCEPT 10.5 DUAL DISC INSTALLATION INSTRUCTIONS
CONCEPT 10.5 DUAL DISC INSTALLATION INSTRUCTIONS Congratulations on your purchase of the RAM Concept 10.5 Dual disc clutch system. Please completely read and carefully follow the setup instructions, and
More informationDODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION
More informationBarnett Spring Conversion for Liner
Barnett Spring Conversion for Liner I installed Barnett s spring conversion on my last bike, a 2003 Warrior, and the difference was very noticeable. The Warrior always launched well, but the Barnett springs
More informationInstallation Instructions COMPETITION/PLUS SHIFTER Ford Mustang MT82 6-Speed Manual Transmission Catalog#
Installation Instructions COMPETITION/PLUS SHIFTER 2015-2017 Ford Mustang MT82 6-Speed Manual Transmission Catalog# 3916037 Rev. 00 WORK SAFELY! For maximum safety, perform this installation on a clean,
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationThe Driveshaft Shop Aluminum One Piece Driveshaft (05-10 GT)
Install Time: 2-3 Hours Tools Needed: Metric Hex Key Set 10mm, 13mm, 15mm deep socket 12 point 12mm deep socket ⅜ Rachet 5 ½ Rachet Extensions ½ Drive Breaker Bar Blue Thread Locker Rubber Mallet Pry Bar
More informationDV8 Tire Carrier Manufacturer Part Number TCSTTB-01 Model Number J104640
DV8 Tire Carrier Manufacturer Part Number TCSTTB-01 Model Number J104640 Installation Time: 30 Minutes Tools Required: 19mm Socket 13mm Socket Ratchet T15 Torx Driver T50 Torx Driver Painters Tape Dremel
More informationHow to replace Air Filter and Serpentine Belt in less than one hour on a Porsche S
How to replace Air Filter and Serpentine Belt in less than one hour on a Porsche 997.1 3.8S How to replace your Air Filter cartridge and serpentine belt on a 997.1 3.8S engine in less than one hour. Disclaimer:
More informationGM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions
GM 6-Cylinder Cam Tool Set 3.0L and 3.2L Operating Instructions Set Includes: Locking Tool... 536594 Locking Tool... 536595 Crankshaft Holding Tool... 536596 Alignment Gauge... 536608 Belt Installation
More informationFig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover
Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and
More informationSR Performance Twin 62mm Throttle Body for GT
Required Tools: SR Performance Twin 62mm Throttle Body for 2005-2010 GT Flat-head screwdriver Ratchet Small extension 10mm socket 8mm socket T20 Torx bit Needle nose pliers 5mm allen wrench Recommended
More information15.Timing Belt Assembly
MECHANICAL 15.Timing Belt Assembly A: REMOVAL 1. TIMING BELT 1) Remove the V-belt. 2) Remove the crank pulley.
More informationFORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1)
FORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack
More informationPlease take time to read and understand these installation instructions.
2014- Current C7 Corvette Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service center or professional
More informationSlowly lower the floor jack. The spring will then come right out.
Jack up the rear, install a set of jack stands and remove the rear tires. Put a floor jack under the lower transverse link (lower control arm) jack up the lower control arm about one inch. With the jack
More information07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714-630-0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: K886764 07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES PARTS LIST QTY LIFT
More informationThe spacers can be made out of.750 round aluminum bar with a.3125 to.318 hole drilled in center.
SECTION I : FRONT COVER INSTALLATION With Crankshaft, Camshaft and oil Galley plugs installed in engine, you need to verify that the front cover clears the oil galley plugs and fits on engine block. The
More informationJBA Cat4ward Shorty Header Install (05-10 Mustang GT and Bullitt)
JBA Cat4ward Shorty Header Install (05-10 Mustang GT and 08-09 Bullitt) Installation Time: 6-8 Hours (Depending on Tools and Help) Tools Required: 8mm Socket 10 mm Socket 13mm Socket 15mm Deep Socket Ratchet
More informationLong Tube Header Installation For Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C
Long Tube Header Installation For 2005-2008 Dodge Challenger SRT-8 & R/T, Charger SRT-8 & R/T, Magnum SRT-8 & R/T & Chrysler 300 SRT-8 & 300C Precision manufactured using high quality austenitic stainless
More information2005 Saturn L ENGINE Engine Mechanical - 3.0L (L81) - L300
Crankcase Vent Housing Removal Fig. 324: Removing & Installing Engine Vent Housing 1. Remove the hoses from the chamber. 2. Remove the chamber bolts. 3. Remove the chamber. 4. Remove the gasket material.
More informationMultistrada (MTS) Tank Installation Notes. Tools Required. Phase 1: Remove Fairings. Phase 2: Remove Fuel Tank
The California Cycleworks MTS tank provides an aftermarket alternative to the OEM nylon fuel tanks as used on aircooled Desmodue Ducati Multistrada 1100, 1000, and 620 models. This fuel tank is NOT for
More information1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
More information15.Timing Belt. Timing Belt A: REMOVAL ME(STI) TIMING BELT
15.Timing Belt A: REMOVAL NOTE: Perform the work with the engine installed to body when replacing a single part. For operation procedures, refer to Timing Belt in the PM section.
More information2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
More informationZZPerformance.com ZZP 3 Redline Cold Air Intake GEN 2
Tools you will need: Flat Blade Screwdriver Phillips Screwdriver 10mm End Wrench Ratchet Extension 5.5mm Socket 7mm Socket 10mm Socket 13mm Deep Socket ZZPerformance.com ZZP 3 Redline Cold Air Intake GEN
More information15.Timing Belt. Timing Belt A: REMOVAL ME(H4DOTC) TIMING BELT
15. A: REMOVAL 1. TIMING BELT 1) Remove the V-belts. 2) Remove the crank pulley. 3) Remove the timing belt cover.
More information1995 Mitsubishi Montero LS. Ensure timing marks are aligned. Mark timing belt direction of rotation.
TIMING BELT NOTE: Ensure timing marks are aligned. Mark timing belt direction of rotation. Removal 1. Disconnect negative battery cable. Drain engine coolant. Remove engine coolant reservoir tank, fan
More informationHolley Accessory Drive System Part Number Table of Contents
Holley Accessory Drive System Part Number 20-138 Table of Contents Introduction:... 2 Crank Pulley Belt Alignment Determination:... 3 Overview of Parts Required (but NOT included with 20-138 accessory
More informationLooking up the front of the engine from under the radiator. (Picture taken with belt under tension.)
8. If you re replacing the AC compressor drive belt as well, it s time to loosen its belt tensioner. The AC compressor belt tensioner is very obvious under the front of the car. Loosen the 13mm bolt, then
More information3 Turbo Downpipe Installation Audi A3 / Volkswagen GTI / Volkswagen Jetta 2.0L FSI/TSI Turbo CD100013
Please take time to read and understand these installation instructions. APR recommends that installation of this system be performed by a qualified service center or professional muffler installer who
More informationLearning to Set-Up Your Warrior Drive Belt Arizona Warrior (Rev4) BEFORE GETTING STARTED
BEFORE GETTING STARTED 1. A noise one guy calls 'howling' is the same noise another guy calls 'squealing' so unless you are both hearing the noise with your own ears its better to not assume a drive belt
More informationIncluded parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/ Hardware STEP 1
TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please contact H&S Motorsports
More information