Instruction Sheet. Kit Numbers: , , & CRANK PULLEY KIT DISASSEMBLY. Package Contents

Size: px
Start display at page:

Download "Instruction Sheet. Kit Numbers: , , & CRANK PULLEY KIT DISASSEMBLY. Package Contents"

Transcription

1 Instruction Sheet Kit Numbers: 5600, 5700, 5800 & 5300 CRANK PULLEY KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand, and follow all safety practices in Owner/Operator Manual before beginning. 9 6, 7 3 Package Contents Check the contents of your kit for the parts listed below. Also see Figure. 8 4 Item Description Qty Ariens P/N Ground Drive Pulley (5600, 5700) Ground Drive Pulley (5800, 5300) 3 Dome Plug (5600, ) 4 Belt Channel Plug (5800, ) x 3/8" Tapping Screw (5800, 5300) 6 x 3/8 x.79" Spacer (5700, 5300) 7 3/6 x 3/6 x 5/8" Square Key /3" Wave Washer L Wrapped V-Belt Belt Crank Guide x /4" Hex Washer Head Machine Screw -4 x" Hex Washer Head Tapping Screw DISASSEMBLY 0 Figure Models 974, 75, 78, 79, 8, 375, 379. Disconnect spark plug wire.. Move cable adjuster to loosen wheel drive cable. 3. Disconnect the drive cable spring from the transmission bracket. See Figure. 5. Drive Cable Spring. Transmission Bracket Figure Copyright 05 Ariens Company Brillion, WI /5 Page of 8

2 4. Remove blade and blade adapter from the crankshaft. 5. Remove two tapping screws retaining drive pulley guide. Remove guide, pulley and key. IMPORTANT: Discard two tapping screws, drive pulley guide, pulley and key. 6. Remove belt channel guides. Discard screws. 7. Pull belt over end of crankshaft to allow belt to slide out through belt channel. 8. Rotate transmission backward to remove hardware, then adjust to loosen belt. 9. Remove belt and pull through the belt channel. See Figure Blade. Blade Adapter 3. Drive Pulley Guide 4. Belt Channel Guides 5. Engine Pulley with Key 6. Transmission 7. Transmission Bracket 8. Belt 9. Belt Channel 0. Transmission Pulley. Crankshaft Figure /5 Page of 8

3 DISASSEMBLY Models 976, 77. Remove two bolts from blade and remove blade. See Figure Loosen adjustment nuts on BBC engagement cable. Loosen front nut until threads are no longer engaged and nut is loose on the cable. See Figure Insert a /4" (6 mm) pry bar or similar tool into the hole in the clutch actuating lever. Pry lever to the right (clockwise) and disconnect cable spring from clutch lever. Gradually release lever. 5. While holding anti-rotation arm in position with pry bar, remove anti-rotation shoulder bolt. Gradually release the spring tension and allow the anti-rotation arm to rotate counter-clockwise. 6. Remove BBC spring. 7. Remove blade brake clutch and washers from engine shaft Blade Bolts. Blade Figure 4. Remove center bolt and three washers. See Figure BBC Engagement Cable. Front Adjustment Nut 3. Clutch Actuating Lever 4. Cable Spring 5. Anti-rotation Arm 6. Anti-rotation Shoulder Bolt 7. BBC Spring 8. Blade Brake Clutch Figure 6 8. Center Bolt. Washers Figure 5 8. Remove two tapping screws retaining drive pulley guide. Remove guide, pulley, and key. IMPORTANT: Discard two tapping screws, drive pulley guide, pulley and key /5 Page 3 of 8

4 9. Remove BBC baffle. See Figure Remove two tapping screws retaining inner belt guides and remove guides. Discard screws. See Figure Crankshaft Belt Guide. BBC Baffle 3. Inner Belt Guide Figure 7. Engine Pulley with Key. Transmission 3. Transmission Bracket 4. Belt 5. Belt Channel 6. Transmission Pulley 7. Crankshaft Figure 8. Pull belt over end of crankshaft to allow belt to slide out through belt channel.. Rotate transmission backward to remove hardware, then adjust to loosen belt. 3. Remove belt and pull through the belt channel. See Figure /5 Page 4 of 8

5 RE-TAP BELT GUIDE HOLES All Models Use the included -4 x" hex washer head tapping screw to enlarge the belt guide attaching hole threads.. Insert tapping screw (item ) into each of the four attaching holes. See Figure 9.. Tighten fastener until it is approximately /4" into each hole. IMPORTANT: Do not exceed /4" depth. 3. Clean all grass and debris from belt channel. Re-tap four holes. Do not exceed /4" depth. Belt Channel Plug Item 5 Item 4 Dome Plug Item 3 Figure 9 INSTALL BELT CHANNEL PLUG Models 974, 75, 78, 79, 8, 375, 379 NOTICE: Install either sheet metal plug (item 4) or plastic dome plug (item 3), depending on mower/kit. Mowers equipped with BBC (976, 977) do not require a plug, as the cable routes through this hole. Belt Channel Plug. Install metal plug (item 4) using two 0-4 x 3/8" tapping screws (item 5). Hold plug in position from inside of channel while securing screws. See Figure 0. Dome Plug. Insert dome plug (item 3) into hole in belt channel. Plug snaps into position. See Figure 0. REASSEMBLY Figure 0 Models 974, 75, 78, 79, 8, 375, 379 See Figure. Route belt (item 9) through belt channel.. Route belt around transmission pulley and reinstall transmission bracket and hardware. 3. Rotate transmission back into location. Loop belt over crankshaft end. 4. Models 974, 78, 375, 379 only: Install spacer (item 6) onto crankshaft. IMPORTANT: Install new engine pulley (item ) with thick side of pulley toward engine. See Figure for orientation /5 Page 5 of 8

6 5. Install square key (item 7) and wave washer (item 8). Item 6 (976 Only) Item 9 Item 6 (974, 78, 375, 379 Only) Item 7 Item 9 Item Item 8 Item Item 7 Item 8 Item 0 Item Washer 976: Qty = 977: Qty = Item 0 Item Figure 6. Install belt channel guides and belt crank guide (item 0) using four -4 x /4" screws (item ). IMPORTANT: Do not use original screws. Do not over tighten. 7. Replace blade adapter, blade, flat washer, lock washer and bolt on shaft and torque to lbf-ft (5 68 N-m). NOTICE: Bolt must fully compress lock washer. 8. Connect the wheel drive cable spring to the transmission bracket. 9. Adjust wheel drive cable (see Adjust Wheel Drive Control on page 8). 0. Connect spark plug wire. REASSEMBLY Models 976, 77 See Figure. Route belt (item 9) through belt channel.. Route belt around transmission pulley and reinstall transmission bracket and hardware. 3. Rotate transmission back into position. 4. Loop belt over crankshaft end. 5. Model 976 only: Install spacer (item 6) onto crankshaft. IMPORTANT: Install new engine pulley (item ) with thick side of pulley on top. See Figure for orientation. 6. Install key (item 7) and wave washer (item 8). Figure 7. Install belt channel guides and belt crank guide (item 0) using four -4 x /4" screws (item ). IMPORTANT: Do not use original screws. Do not over tighten. 8. Reinstall BBC baffle and tighten hardware. 9. Install washers and BBC assembly on engine shaft. Ensure that key in BBC is aligned with keyway on engine shaft. See Figure. 0. Reinstall BBC spring.. Using pry bar, rotate BBC assembly clockwise until anti-rotation arm is aligned with shoulder bolt bracket. Install bolt and fully tighten. See Figure 3.. Using a /4" (6 mm) pry bar or similar into the clutch actuating lever. Pry lever to the right (clockwise) /5 Page 6 of 8

7 4 3 Align anti-rotation arm with shoulder bolt bracket here. Figure 3 3. Reattach cable spring to clutch actuating lever. See Figure Gradually release spring tension until pry bar is loose and can be removed. 5. Install center bolt and washers. Torque bolt to 55 lbf-ft (75 N m). See Figure Reinstall front lock nut on BBC engagement cable. Pull on the cable to allow only a slight amount of slack and hand tighten front adjustment nut against the cable bracket. Tighten the rear adjustment nut. See Figure Replace blade and two bolts on blade brake clutch. Torque bolts to 38 lbf-ft (5 N m). 8. Connect the wheel drive cable spring to the transmission bracket. 9. Adjust wheel drive cable (see Adjust Wheel Drive Control on page 8). 0. Connect spark plug wire.. Front Adjustment Nut. Cable Bracket 3. Rear Adjustment Nut 4. Cable Figure /5 Page 7 of 8

8 ADJUST WHEEL DRIVE CONTROL All Models. See Figure 5.. The unit should stop immediately when the wheel drive control lever is released and not creep forward when the wheel drive control lever is disengaged with the engine running. 3. The unit s forward speed should increase as the wheel drive control lever is moved closer to the handlebar. If the unit does not accelerate smoothly or seems to slip under load, adjust the wheel drive control cable. IMPORTANT: DO NOT adjust the cable so the transmission does not return to neutral and stop the unit when the wheel drive control is released. To Adjust:. Stop engine and wait for all moving parts to completely stop.. Clean any dirt or debris from the drive components. 3. Make sure the return spring is properly connected to transmission bracket. 4. On the handlebar, loosen cable nuts away from bracket. See Figure Move the wheel drive cable adjuster up or down the handlebar. See Figure 9. To increase speed, move the cable adjuster down the handlebar. To decrease speed, move the cable adjuster up the handlebar.. Cable Adjuster. Cable Nuts Razor Fig 9 Figure 5 6. Check the adjustment. A. Start the engine. B. Slowly squeeze the wheel drive control lever against the handlebar. The unit should move forward smoothly and increase in speed as handle is moved closer to handlebar. C. Release the wheel drive control lever. The unit should stop immediately and not creep forward. CHECK OPERATOR PRESENCE CONTROL / BLADE BRAKE CLUTCH (OPC / BBC) HANDLE Models 976, 977 The blade must stop within 3 seconds after releasing OPC / BBC handle. If the blade does not stop, adjust as necessary or inspect and repair before using /5 Page 8 of 8

Instruction Sheet Kit Number:

Instruction Sheet Kit Number: Instruction Sheet Kit Number: 7914400 POWERED DECK LIFT KIT WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand and follow all safety practices

More information

Instruction Sheet Kit Number:

Instruction Sheet Kit Number: Instruction Sheet Kit Number: 72101800 TRACK CONVERSION KIT For All Wheel-Drive 921000 Models WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. Read, understand,

More information

G3 UHT TRANSMISSION. G3 UHT Transmission Replacement. G3 UHT Transmission Removal

G3 UHT TRANSMISSION. G3 UHT Transmission Replacement. G3 UHT Transmission Removal G3 UHT Transmission Replacement The following procedures cover replacing the left hand UHT Transmission. The same procedures can be followed to remove the right hand UHT Transmission. 5. Raise the seat

More information

Service Bulletin. Date: Jan No. B Ariens Company 655 W. Ryan St. P.O. Box 157 Brillion, WI

Service Bulletin. Date: Jan No. B Ariens Company 655 W. Ryan St. P.O. Box 157 Brillion, WI Date: Jan. 2007 No. B-2029 Service Bulletin Ariens Company 655 W. Ryan St. P.O. Box 157 Brillion, WI 54110-0157 www.ariens.com Product Family: Sno-Thro Subject: Pinion Shaft Rotation Kits 52603400 and

More information

62 Deck Idler Kit High Speed

62 Deck Idler Kit High Speed Part No. 00 FORM NO. -899 6 Deck Idler Kit High Speed For Model 70 Serial No. 99000 to 99000 For Model 7 Serial No. 9900 to 99000 INSTALLATION INSTRUCTIONS Loose Parts Note: Use the chart below to identify

More information

CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT

CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.

More information

Camshaft Timing Chain, Sprocket, And Tensioner Replacement

Camshaft Timing Chain, Sprocket, And Tensioner Replacement 2007 Pontiac Solstice - Engine Mechanical > Engine Mechanical - 2.0L > Repair Instructi... Page 1 of 29 2007 Pontiac Solstice : Engine Mechanical > Engine Mechanical - 2.0L > Repair Instructions - On Vehicle

More information

Razor. Owner/Operator Manual Manuel du Propriétaire/Utilisateur. Models LMP (SN ) LMSP (SN )

Razor. Owner/Operator Manual Manuel du Propriétaire/Utilisateur. Models LMP (SN ) LMSP (SN ) Razor Owner/Operator Manual Manuel du Propriétaire/Utilisateur Models 973 LMP (SN 08000 +) 975 LMSP (SN 08000 +) 977 LMSP BBC (SN 08000 +) 979 LMSPE (SN 08000 +) 988 LMSP (SN 0000 +) 989 LMSP BBC (SN 0000

More information

Walk-Behind Lawn Mowers

Walk-Behind Lawn Mowers Walk-Behind Lawn Mowers Parts Manual Models 171 LM21 16 LM21S 17 LM21SW 04502100 / Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied with the unit.

More information

Model Serial Number Ranges Description LE Deluxe

Model Serial Number Ranges Description LE Deluxe Service Campaign Ariens Company 655 W. Ryan St. Brillion, WI 54110-1072 www.ariens.com Product Family: 921020 Sno-Thro 30LE Deluxe Subject: Attachment Belt Engagement Dealer Action: Replace Attachment

More information

Quick Start Guide Sno-Tek 24E ( s/n & up)

Quick Start Guide Sno-Tek 24E ( s/n & up) Quick Start Guide Sno-Tek 24E (920402 s/n 75000 & up) Step 1: Assemble Handlebars Step 2: Install Discharge Chute and Discharge Chute Crank Step 3: Install Remote Deflector Cable Step 4: Check Function

More information

CAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.

CAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2. CAMSHAFT TIMING CHAIN, SPROCK... CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT (LE5 OR LE9) (ENGINE MECHANICAL - 2.2L OR 2.4L) Document ID# 2133175 Camshaft Timing Chain, Sprocket, and Tensioner

More information

Quick Start Guide Compact 22 LE ( s/n & up)

Quick Start Guide Compact 22 LE ( s/n & up) Quick Start Guide Compact 22 LE (920013 s/n 75000 & up) Step 1: Assemble Handlebar Step 2: Install Discharge Chute Step 3: Install Discharge Chute Crank Step 4: Check Function of Dual Handle Interlock

More information

XL HYDROSTATIC TRANSAXLES

XL HYDROSTATIC TRANSAXLES Purging Procedures Due the effects air has on efficiency in hydrostatic drive applications, it is critical that it be purged from the system. These purge procedures should be implemented any time a hydrostatic

More information

Walk-Behind Lawn Mowers

Walk-Behind Lawn Mowers Walk-Behind Lawn Mowers Parts Manual Models 160 - LM21 182 - LM21 18 - LM21S 184 - LM21SW 04056800 6/10 Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied

More information

TIMING CHAIN COMPONENTS

TIMING CHAIN COMPONENTS h Page 1 of 52 TIMING CHAIN COMPONENTS ht Page 2 of 52 Fig. 24: Displaying Timing Chain Components (1 Of 2) Page 3 of 52 Fig. 25: Displaying Timing Chain Components (2 Of 2) Page 4 of 52 REMOVAL NOTE:

More information

Discount-Equipment.com

Discount-Equipment.com REQUIRED TOOLS LS Series Remix Shaft Installation Instructions /8", /6", /2" Allen Wrenches Snap Ring Pliers (Light Duty) /" Combination Wrench Loctite #22 Blue /" Socket w/ /8" Ratchet Electric Drill

More information

Quick Start Guide Compact 24 LET ( s/n & up)

Quick Start Guide Compact 24 LET ( s/n & up) Quick Start Guide Compact 24 LET (920022 s/n 000101 & up) Step 1: Assemble Handlebar Step 2: Install Trigger Cable Assembly Step 3: Install Discharge Chute Step 4: Install Discharge Chute Crank Step 5:

More information

Installation Guide Philips MP90 VHM Wall Mount Kit

Installation Guide Philips MP90 VHM Wall Mount Kit Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note

More information

Light Shipping Location. Remove nut to detach headlight from under dash. Keep nut to mount light on unit. Figure 5

Light Shipping Location. Remove nut to detach headlight from under dash. Keep nut to mount light on unit. Figure 5 Install Headlight (900, 0, 05) (Figure 5). Remove headlight from location under dash panel. Keep nut for installation.. Attach headlight to bolt on right side of the dash. Fasten with nut removed in step..

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS PZ 60 inch Side Discharge Deck Kit - 966555302 Tools Required ½" socket or wrench (battery terminals, strut shaft). ½" breaker bar with 2-3" extension (relieve tension on idler arms). Refer to Operators

More information

Agri-Fab OWNERS MANUAL. Model No " FINISH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully

Agri-Fab OWNERS MANUAL. Model No  FINISH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully Agri-Fab OWNERS MANUAL Model No. 45-0305 63" FINISH CUT TRAILMOWER CAUTION: Read Rules for Safe Operation and Instructions Carefully NOTE: Your mower deck will require a 12 volt battery to operate. This

More information

Discount-Equipment.com

Discount-Equipment.com LS40D, LS40TD, LS50TD, LS60TD LS-Series Remix Shaft Coupler Retrofit Kit Installation Instructions The following instructions are intended to assist the user in the installtion of the LS-Series Remix Shaft

More information

Polaris 340 & ATV Power Module Training and Troubleshooting Guide

Polaris 340 & ATV Power Module Training and Troubleshooting Guide Polaris 340 & ATV Power Module Training and Troubleshooting Guide Summary: This guide is intended as a training tool for the mechanical evaluation and troubleshooting of a 340 or ATV power module only.

More information

Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Intermediate Pulley Shaft and Bearings

Lifecycle Upright Bikes LC95, LC91, LC85, C9, C7, 95Ce, 95Ci, 93Ci, and 90C How To... Replace the Intermediate Pulley Shaft and Bearings How To... Replace the Pulley Shaft and s Special Service Tools: Service Tool Kit Part Number: ToolKit 1. Remove the side covers. Refer to, How To Remove Pedals, Pedal Levers, and Side Shrouds. Main Drive

More information

INSTALLATION GUIDE. Kawasaki KLR Manual Revision:

INSTALLATION GUIDE. Kawasaki KLR Manual Revision: REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Kawasaki KLR650 191-640 Manual Revision: 030308 2007 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714

More information

Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches

Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches Step Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches Work Description All work should be performed in accordance with NFPA 70E. Tools Required: Personal Protective

More information

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. M18 Sawzall

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. M18 Sawzall Pull both Brush Tubes (25) back before removing or installing the Armature (2) to prevent damage to the commutator. Brush Tube SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

More information

Timing Belt: Service and Repair Timing Belt Replacement

Timing Belt: Service and Repair Timing Belt Replacement 2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft

More information

Service Manual. Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Service Manual. Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Service Manual Bolens 683 Series Box Frame Tractor IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY This Service Manual is not a substitute for the Operator s Manual. You must read, understand and

More information

2620 Series Flex Drive Shaft Kit Installation Instructions P/N for SRM-2620T

2620 Series Flex Drive Shaft Kit Installation Instructions P/N for SRM-2620T Kit 90206 and 90207includes: Part Number Description Qty A556001760 Clutch Drum 1 61092255931 Main Pipe Fixture 1 90070100012 Drum Retaining Ring 1 C506000470 Flexible Drive Cable 1 P021051520 Gear Case

More information

Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches

Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches Step Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches Work Description All work should be performed in accordance with NFPA 70E. Tools

More information

Models Affected: Visions with Propane Engines CORRECTIVE ACTION ---- PROCEDURE

Models Affected: Visions with Propane Engines CORRECTIVE ACTION ---- PROCEDURE Propane Belt Squeal Models Affected: Visions with Propane Engines ISSUE Front End Accessory Drive (FEAD) Belt chirping/squealing caused by improper fore-aft crankshaft pulley positioning. CORRECTIVE ACTION

More information

SERVICE PARTS LIST. SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M18 Sawzall STARTING SERIAL NO.

SERVICE PARTS LIST. SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M18 Sawzall STARTING SERIAL NO. Pull both Brush Tubes (25) back before removing or installing the Armature (2) to prevent damage to the commutator. Brush Tube SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

More information

Service Bulletin No. 2994

Service Bulletin No. 2994 MODEL TYPE SECTION/GROUP DATE E / J Series Coaches equipped with Linnig Fan Clutch Service Information 6--Cooling July 30, 2008 SUBJECT CONDITIONS LINNIG FAN CLUTCH MOUNTING NUTS Parts may be purchased

More information

TABLE OF CONTENTS I. SERVICE & MAINTENANCE PROCEDURES. 1) Opening and closing of door latch. 2) Latch assembly and adjustment

TABLE OF CONTENTS I. SERVICE & MAINTENANCE PROCEDURES. 1) Opening and closing of door latch. 2) Latch assembly and adjustment TABLE OF CONTENTS I. SERVICE & MAINTENANCE PROCEDURES 1) Opening and closing of door latch 2) Latch assembly and adjustment 3) Latch cover removal and replacement 4) Upper slider track adjustment 5) Lower

More information

Quick Start Guide Deluxe 30 ( s/n 101 & up)

Quick Start Guide Deluxe 30 ( s/n 101 & up) Quick Start Guide Deluxe 30 (921032 s/n 101 & up) Step 1: Assemble Handlebars Step 2: Connect Headlight Wire Harness Step 3: Install Discharge Chute Step 4: Install Discharge Chute Crank Step 5: Install

More information

Walk-Behind Lawn Mowers

Walk-Behind Lawn Mowers Walk-Behind Lawn Mowers Parts Manual Models 0 - P - SP - DSP 3 - DESP - P CARB 5 - SP CARB 000C /0 Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied

More information

Wheel Horse. 36 Tiller. Model No & Up. Operator s Manual

Wheel Horse. 36 Tiller. Model No & Up. Operator s Manual FORM NO. 8 9 Rev. A Wheel Horse 6 Tiller for Classic Garden Tractors Model No. 7970 690000 & Up Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the

More information

Self-propelled Chipper Shredder Vacuum

Self-propelled Chipper Shredder Vacuum 2.11. Confirm that the drive gears are installed on the correct side. See Figure 2.11. 3. TRANSMISSION REMOVAL 3.1. Disconnect the H.T. lead from the spark plug. 3.2. Remove collection bag or blower chute.

More information

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. 18 Volt Sawzall STARTING SERIAL NO. Spindle (38) to be assembled

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. 18 Volt Sawzall STARTING SERIAL NO. Spindle (38) to be assembled Pull Brush Tubes () back before removing or installing the Armature (21) to protect commutator. SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 18 Volt Sawzall CATALOG NO. 2620-20

More information

Air Commander Part No

Air Commander Part No EASYSTREET Air Commander Part No. 26901 www.airliftcompany.com MN-508 (05504) NPR 5129 Please read these instructions completely before proceeding with installation Front View Side View Hardware Item P/N

More information

SCAMP AND UTILITY MODELS SELF-PROPELLED BELT DRIVE SERVICING 4502, 4503, 8602, 8603 WITH F SERIES ENGINES

SCAMP AND UTILITY MODELS SELF-PROPELLED BELT DRIVE SERVICING 4502, 4503, 8602, 8603 WITH F SERIES ENGINES 4502, 4503, 8602, 8603 WITH F SERIES ENGINES Adjustments and servicing of the Scamp and Utility self-propelled mowers are very different from all previous models of self-propelled mowers. BEFORE ANY ADJUSTMENTS

More information

Auger Belt Tension Adjustment DB7659

Auger Belt Tension Adjustment DB7659 Rev 1.0 3-23-13 Auger Belt Tension Adjustment DB7659 WARNING Entanglement Hazard - Before performing any adjustment procedures, make sure the engine is off and remove the spark plug wire from the spark

More information

R25 Recumbent Bike ASSEMBLY & PARTS MANUAL

R25 Recumbent Bike ASSEMBLY & PARTS MANUAL R25 Recumbent Bike ASSEMBLY & PARTS MANUAL MA902 Recreation Supply Inc. Model No. R25.1 P.O. BOX 181 BODYCRAFT is a division of Recreation Supply Sunbury, OH 43074 www.bodycraft.com 800-990-5556 info@bodycraft.com

More information

Mandatory X Information Recommended Change. Series/Parts Affected: LS40D, LS40TD, LS50TD and LS60TD Concrete Pumps

Mandatory X Information Recommended Change. Series/Parts Affected: LS40D, LS40TD, LS50TD and LS60TD Concrete Pumps Service Bulletin No. CP20060428 Subject: Remix Shaft Coupler Retrofit Kit Model: LS40D, LS40TD, LS50TD & LS60TD Product Group: Concrete Pump Date: April 28, 2006 SERVICE BULLETIN Group: CP Mandatory X

More information

Air Commander Late Model Ford F-150

Air Commander Late Model Ford F-150 EASYSTREET Air Commander Late Model Ford F-150 www.airliftcompany.com MN-544 (02506) ECR 5206 Please read these instructions completely before proceeding with installation The oil level in the compressor

More information

Riding Mowers. Z44 and Z52 Accu-Z Razor (S/N and above) SM Service Manual Printed 9/24/09

Riding Mowers. Z44 and Z52 Accu-Z Razor (S/N and above) SM Service Manual Printed 9/24/09 Riding Mowers Z44 and Z52 Accu-Z Razor (S/N 472620 and above) 23802 357-044SM Service Manual 2006 Printed 9/24/09 Copyright 2006 All rights Reserved Land Pride provides this publication as is without warranty

More information

ASSEMBLY INSTRUCTIONS FOR CHARGER AND THE BOSS QUICK ATTACH GRASS BAGGER

ASSEMBLY INSTRUCTIONS FOR CHARGER AND THE BOSS QUICK ATTACH GRASS BAGGER ASSEMBLY INSTRUCTIONS FOR CHARGER AND THE BOSS QUICK ATTACH GRASS BAGGER \ \ \ \ ~\ P P-12102 (7/2005) TABLE OF CONTENTS SECTION PAGE WARNING 1 BLOWER PULLEY INSTALLATION 2 ENGINE GUARD REMOVAL BOSS 3

More information

Bulletin Information Model Year(s) Affected

Bulletin Information Model Year(s) Affected Date Issued Bulletin Information Model Year(s) Affected Model(s) Affected TSB # 1/27/06 2005 Present LADB, EXDP 258 Systems Affected Air Conditioning & Heating Electrical Components Appliances & Accessories

More information

SERVICE PARTS LIST. M18 FUEL ONE KEY SAWZALL Reciprocating Saw H31A BULLETIN NO

SERVICE PARTS LIST. M18 FUEL ONE KEY SAWZALL Reciprocating Saw H31A BULLETIN NO 00 FIG. PART NO. DESCRIPTION OF PART NO. REQ. 1 45-12-0040 Gearcase Insulator 1 2 40-50-8805 Extension Spring 1 3 31-11-0105 Barrel Cam 1 4 34-60-3700 Retaining Ring 1 5 --------------- Front Cam 1 6 ---------------

More information

Valtek Auxiliary Handwheels and Limit Stops

Valtek Auxiliary Handwheels and Limit Stops Valtek Auxiliary s and Limit Stops Table of Contents Page 1 General information 2 Installation 2 Side-mounted handwheels, size 25 and 50 (linear actuators) 3 Side-mounted handwheels, size 100 and 200 (linear

More information

TOYOTA 4-RUNNER TOWING HITCH Preparation

TOYOTA 4-RUNNER TOWING HITCH Preparation Preparation Part Number: PT228-89460 Kit Contents 1 1 High Assembly 2 1 Wiring Harness Bracket 3 1 Hardware Bag 4 1 Hitch Cover 5 2 Frame Spacer 6 2 Center Spacer 7 1 Close-out Panel Hardware Bag Contents

More information

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual FORM NO. 8 Rev A Wheel Horse Snowthrower for 5xi Lawn and Garden Tractors Model No. 7966 890050 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information

More information

INSTALLATION & USER S GUIDE

INSTALLATION & USER S GUIDE REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit with Adjustable Slave Cylinder INSTALLATION & USER S GUIDE Doc ID: 191-7704A Doc Rev: 102915 OVERVIEW This kit replaces the OEM core clutch components including

More information

SERVICE PARTS LIST. SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M18 FUEL SAWZALL Reciprocating Saw STARTING SERIAL NO.

SERVICE PARTS LIST. SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M18 FUEL SAWZALL Reciprocating Saw STARTING SERIAL NO. 47(5x) 46 45 00 44 0 59 43 42 84 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). CATALOG NO. 2720-20 51 57 46 47 48 59 83 64 77 48 47(2x) 49(2x) 40 58 41 82 51 40

More information

TOYOTA COROLLA EC REARVIEW MIRROR Preparation

TOYOTA COROLLA EC REARVIEW MIRROR Preparation Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,

More information

Not for Reproduction. BILLY GOAT AERATOR Owner's Manual AE401, AE401H, AE401H5T Replacement Parts. AE Owner s Manual TINE ROW KIT TINE KIT P/N

Not for Reproduction. BILLY GOAT AERATOR Owner's Manual AE401, AE401H, AE401H5T Replacement Parts. AE Owner s Manual TINE ROW KIT TINE KIT P/N BILLY GOAT AERATOR Owner's Manual AE401, AE401H, AE401H5T Replacement Parts TINE ROW KIT Complete tine row set for replacement of one complete row of tines. Includes mounting plates, spacer, and all hardware.

More information

LS Series. Remix Shaft Installation Instructions REQUIRED TOOLS PARTS WORK SAFELY! PREPARATION/SAFETY PROCEDURES

LS Series. Remix Shaft Installation Instructions REQUIRED TOOLS PARTS WORK SAFELY! PREPARATION/SAFETY PROCEDURES REQUIRED TOOLS LS Series Remix Shaft Installation Instructions /8", /6", /2" Allen Wrenches Snap Ring Pliers (Light Duty) /" Combination Wrench Loctite #22 Blue /" Socket w/ /8" Ratchet Electric Drill

More information

Collector Drive for 44 Mower

Collector Drive for 44 Mower FORM NO. -80 Collector Drive for Mower Model No. 7955-990000 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the safety

More information

SERVICE PARTS LIST. 18 Volt Sawzall B58D BULLETIN NO CATALOG NO

SERVICE PARTS LIST. 18 Volt Sawzall B58D BULLETIN NO CATALOG NO Tab Square Groove CATALOG NO. 2620-20 SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 18 Volt Sawzall IMPORTANT Field (22) to be assembled with tapper to back and square groove

More information

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover

Fig. 1: Remove the bolts which fasten the upper timing belt cover... Fig. 2:... and remove the cover Show Timing Belt and Covers REMOVAL & INSTALLATION 1983 87 626 NOTE: For access, safely support the car, then remove the right front wheel and splash shield. 1. Loosen the alternator mounting bolts and

More information

HAND THROTTLE KIT For Workman 3000 Series

HAND THROTTLE KIT For Workman 3000 Series FORM NO. 7 6 MODEL NO. 0746 INSTALLATION INSTRUCTIONS HAND THROTTLE KIT For Workman 000 Series. Position vehicle on a clean, level surface, stop engine, engage parking brake and remove key from ignition

More information

Models Affected: Certain 2015 & 2016 All American Front Engine and Vision Buses Equipped with Hydraulic Brakes ISSUE _ CORRECTIVE ACTION _

Models Affected: Certain 2015 & 2016 All American Front Engine and Vision Buses Equipped with Hydraulic Brakes ISSUE _ CORRECTIVE ACTION _ R E C A L L C A M P A I G N -- R 1 4 X R ---- Models Affected: Certain 2015 & 2016 All American Front Engine and Vision Buses Equipped with Hydraulic Brakes ISSUE _ CORRECTIVE ACTION -- -- _ The parking

More information

INSTALLATION INSTRUCTIONS FOR: DECK LIFT KIT 629GN-001A

INSTALLATION INSTRUCTIONS FOR: DECK LIFT KIT 629GN-001A INSTALLATION INSTRUCTIONS FOR: DECK LIFT KIT 629GN-001A 1. SHUT OFF THE ENGINE AND SET THE PARK BRAKE. 2. ROTATE THE FRONT CASTER WHEELS AWAY FROM THE DECK. (SEE ILLUSTRATION 3) 3. REMOVE THE DECK HEIGHT

More information

SERVICE PARTS LIST. 18 Volt Sawzall STARTING SERIAL NO. B58B BULLETIN NO

SERVICE PARTS LIST. 18 Volt Sawzall STARTING SERIAL NO. B58B BULLETIN NO Tab Square Groove CATALOG NO. 2620-20 IMPORTANT Field (22) to be assembled with tapper to back and square groove to the top. Motor Cage (35) must be oriented with tab to the bottom. SERVICE PARTS LIST

More information

36 Tiller Wheel Horse Lawn and Garden Tractor Attachment

36 Tiller Wheel Horse Lawn and Garden Tractor Attachment Form No. 9 6 Rev B 6 Tiller Wheel Horse Lawn and Garden Tractor Attachment Model No. 797 890000 and Up Operator s Manual English(En) Contents Page Introduction................................ Safety.....................................

More information

Z Master. 62 Mower. for Z Master Z 255 Traction Unit. Model No & UP. Operator s Manual

Z Master. 62 Mower. for Z Master Z 255 Traction Unit. Model No & UP. Operator s Manual FORM NO. 9 88 Z Master 6 Mower for Z Master Z 55 Traction Unit Model No. 7408 89000 & UP Operator s Manual IMPORTANT: Read this manual carefully. It contains information about your safety and the safety

More information

Loose Parts Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts Note: Determine the left and right sides of the machine from the normal operating position. Brake Kit Dingo TX 0 & Compact Utility Loader Part No. 0 0 & 0 Loose Parts Note: Determine the left and right sides of the machine from the normal operating position. Description Qty. Use Drive wheel Brake

More information

WESCO INDUSTRIAL PRODUCTS, INC. Manual Non Telescoping High Lift Truck. Part Number: &

WESCO INDUSTRIAL PRODUCTS, INC. Manual Non Telescoping High Lift Truck. Part Number: & WESCO INDUSTRIAL PRODUCTS, INC Manual Non Telescoping High Lift Truck Part Number: 272462 & 272463 Note: Operator MUST read and understand these operating instructions before using this Truck. TABLE OF

More information

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. 18 Volt Sawzall STARTING SERIAL NO. See note on page 3.

SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS. 18 Volt Sawzall STARTING SERIAL NO. See note on page 3. Pull Brush Tubes () back before removing or installing the Armature (2) to protect commutator. SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 8 Volt Sawzall CATALOG NO. 2620-20

More information

AIRTEK for Volvo Vehicles Single to Dual Height Control Valve Conversion Kit

AIRTEK for Volvo Vehicles Single to Dual Height Control Valve Conversion Kit Single to Dual Height Control Valve Conversion Kit SUBJECT: 60961-101 and 60961-102 LIT NO: 59310-026 DATE: January 2006 REVISION: A INTRODUCTION Prior to March 2005, some Volvo vehicle configurations

More information

Installation Guide. Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit

Installation Guide. Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit Installation Guide Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter. 2. Describe attachment of Mounting

More information

Installation Instructions

Installation Instructions Roller & Roman Shades Lifting Systems Cassette and Sure-Lift EZ Lift Cordless EZ Pull Standard and Cassette R-Series Clutch SL-Series Clutch Spring Roller Fascias and Valances 3, 4 Flat and 4 Curved Fascia

More information

Lawn Edger Parts Manual

Lawn Edger Parts Manual Lawn Edger Parts Manual Models 80 Lawn Edger 80 Lawn Edger 80 Lawn Edger CE 000D /0 Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied with the unit.

More information

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns

1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available

More information

DFS Vac Collection System 400 Series Z Master

DFS Vac Collection System 400 Series Z Master Form No. 0 DFS Vac Collection System 00 Series Z Master Model No. 780 Serial No. 000000 and Up Operator s Manual Register your product at www.toro.com Original Instructions (EN/GB) Contents Page Introduction................................

More information

160S Rewind Option Kit Installation Instructions

160S Rewind Option Kit Installation Instructions Installation Instructions GENERAL This kit includes the parts and documentation necessary to install the Media Rewind Option into the Zebra 160S printer. Read these instructions thoroughly before attempting

More information

Torqueflite Manual/Automatic Valve Body

Torqueflite Manual/Automatic Valve Body TCI 122400 Torqueflite Manual/Automatic Valve Body This valve body can be installed in a few hours by carefully following directions. Read all instructions first to familiarize yourself with the parts

More information

SETUP, PARTS & MAINTENANCE MANUAL 2 BAG CATCHER

SETUP, PARTS & MAINTENANCE MANUAL 2 BAG CATCHER SETUP, PARTS & MAINTENANCE MANUAL 2 BAG CATCHER MODELS: 970338 2 BAG CATCHER, 36 970339 2 BAG CATCHER, 42 970340 2 BAG CATCHER, 48 970341 2 BAG CATCHER, 52 WARNING: If incorrectly used this machine can

More information

PORSCHE 928. PKT Installation 1.8. No air pump version. Air pump version

PORSCHE 928. PKT Installation 1.8. No air pump version. Air pump version PORSCHE 928 PKT Installation No air pump version Air pump version 1.8 Tools Torque wrench 10mm socket 12mm socket 13mm socket 5mm allen socket 6mm allen socket 8mm allen key Caliper Supplies Blue Loctite

More information

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.

WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components. 4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,

More information

Service Kit A

Service Kit A Service Kit 753-05894A Date: Subject: Models Affected: June 28, 2010 Service Replacement for the 618-04360 and 618-04360A Tiller Transmissions N/A Read through and understand these instructions completely

More information

FIG. 3 BRACKET INSTALLATION. i a. e h f FIG. 4 STATOR OFFSET BRACKET REMOVE OEM SPACER. REPLACE WITH BRACKET 3.

FIG. 3 BRACKET INSTALLATION. i a. e h f FIG. 4 STATOR OFFSET BRACKET REMOVE OEM SPACER. REPLACE WITH BRACKET 3. 700510 IG. 3 BRACKET INSTALLATION E D 11 C B i a b c d e h f g A B C A IG. 4 STATOR OSET BRACKET 14 G REMOVE OEM SPACER. REPLACE WITH BRACKET 3. 9 G 8 2 4 3 DewEze Clutch Pump Kit 700510 ord 6.7L, AA Pump,

More information

Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue

Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter (page 2). 2. Describe

More information

Rekluse Motor Sports. The ProStart Clutch. H-D Sportster (2004 +)

Rekluse Motor Sports. The ProStart Clutch. H-D Sportster (2004 +) Rekluse Motor Sports The ProStart Clutch H-D Sportster (2004 +) Installation Guide Copyright 2006 Rekluse Motor Sports ProStart Revision 1.000 RMS687 H-D Sportster 195-687 Manual Revision: 111308 Rekluse

More information

SET-UP INSTRUCTION & PRE-OPERATION CHECKLIST SNAPPER 21" STEEL DECK COMMERCIAL WALK BEHIND MOWERS

SET-UP INSTRUCTION & PRE-OPERATION CHECKLIST SNAPPER 21 STEEL DECK COMMERCIAL WALK BEHIND MOWERS SET-UP INSTRUCTION & PRE-OPERATION CHECKLIST SNAPPER 21" STEEL DECK COMMERCIAL WALK BEHIND MOWERS INTRODUCTION: The SNAPPER Walk Behind Mowers are shipped almost fully assembled and require minimal set-up.

More information

McCULLOCH. Stroke. 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.)

McCULLOCH. Stroke. 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) SERVICE MANUAL Model Eager Beaver 2010, Mac 3210 Silver Eagle 2012 Eager Beaver 2014, Mac 3214, Silver Eagle 2014 Eager Beaver 2016, Mac 3216, Silver Eagle 2016 Bore Stroke DispL (2.1 cu. in.) (2.1CU.

More information

1996 Aerostar/Ranger/Explorer

1996 Aerostar/Ranger/Explorer Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding

More information

The steering column is of a modular construction and features easy to service electrical switches.

The steering column is of a modular construction and features easy to service electrical switches. file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:

More information

INSTALLATION & USER S GUIDE

INSTALLATION & USER S GUIDE REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit for Kawasaki KX80/85/100 OVERVIEW INSTALLATION & USER S GUIDE Doc ID: 191-7742A Doc Rev: 073015 This kit replaces the OEM core clutch components including

More information

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL

CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment

More information

BILLY GOAT AERATOR Owner's Manual AE401, AE401H, AE401H5T Replacement Parts

BILLY GOAT AERATOR Owner's Manual AE401, AE401H, AE401H5T Replacement Parts BILLY GOAT AERATOR Owner's Manual AE401, AE401H, AE401H5T Replacement Parts TINE ROW KIT TINE KIT Complete tine row set for replacement of one complete row of tines. Includes mounting plates, spacer, and

More information

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).

HYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388). TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all

More information

TUFF TORQ TRANSAXLE. Tuff Torq Hydrostatic Transaxle. Transaxle Removal Tuff Torq

TUFF TORQ TRANSAXLE. Tuff Torq Hydrostatic Transaxle. Transaxle Removal Tuff Torq Tuff Torq Hydrostatic Transaxle Internal Service 3. Disconnect the cotter pin and the washer to the brake rod (Figure 63). Internal service information is contained in the Tuff Torq KGIA Transaxle Service

More information

CHAPTER 4 GOVERNORS AND LINKAGE

CHAPTER 4 GOVERNORS AND LINKAGE CHAPTER 4 S AND LINKAGE Main Menu GENERAL INFORMATION Tecumseh 4 cycle engines are equipped with mechanical type governors. The governor s function is to maintain a R.P.M. setting when engine loads are

More information

1992 Mitsubishi 3000GT VR-4

1992 Mitsubishi 3000GT VR-4 TIMING BELT Removal (Diamante SOHC) 1. Remove left front and left side splash shields. Using engine hoist, lift engine just enough to remove weight from engine mounts. Remove drive belts. Remove A/C tensioner

More information

FIELD & BRUSH MOWER SERIES 0

FIELD & BRUSH MOWER SERIES 0 Parts Manual for SERIES 0 MODEL FB13250BS FB13250BV FB15250KW McDonough, GA, 30253 U.S.A. COPYRIGHT 2005 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision 1, 8/30/2005 Table Of Contents PAGE GROUP

More information

Agri-Fab OWNERS MANUAL. Model No " ROUGH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully

Agri-Fab OWNERS MANUAL. Model No  ROUGH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully Agri-Fab OWNERS MANUAL Model No. 45-0362 CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts 42" ROUGH CUT TRAILMOWER NOTE: Your mower deck will

More information