7600 Series Center Drive Conveyors

Transcription

1 7600 Series Center Drive Conveyors Installation, Maintenance and Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box Cottonwood Ave. TEL: TEL: Hartland, WI USA FAX: FAX: Rev. B For other service manuals visit our website at:

2 Table of Contents Introduction... Warnings General Safety... Product Description... Specifications... Flat Belt 7600 Series Center Drive Conveyor... Conveyor Supports... 5 Specifications... 5 Installation... 6 Required Tools... 6 Recommended Installation Sequence... 6 Conveyors Longer than 0 ft (08 mm)... 6 Connecting Components... 6 Wear Strip Installation... 7 Standard Wear Strips... 7 Stainless Steel Sheet Bed Plates (optional)... 7 Lifter Installation... 8 Belt Installation... 8 Guide Installation... 0 All Conveyors... 0 Belt Return Installation... 0 Flat Belt... 0 Scraper Installation... Stand Installation... Drive Package Installation... Mounting Block Installation... Preventive Maintenance and Adjustment... Required Tools... Checklist... Cleaning... Routine Cleaning... Standard Conveyors... Conveyors with Lifters... 5 Periodic Cleaning... 5 Lubrication... 5 Conveyor Bearings... 5 Wearstrips and Belt Returns... 5 Scraper... 5 Maintaining the Conveyor Belt... 5 Troubleshooting... 5 Conveyor Belt Replacement... 6 Conveyors with Guides... 6 Standard Belts... 6 Conveyor Belt Tensioning... 7 Conveyor Belt Tracking... 8 Tracking Procedure... 8 Conveyor Belt Tracking at Tails... 8 Introduction CAUTION Some illustrations may show guards removed. DO NOT operate equipment without guards. Upon receipt of shipment: Compare shipment with packing slip. Contact factory regarding discrepancies. Inspect packages for shipping damage. Contact carrier regarding damage. Accessories may be shipped loose. See accessory instructions for installation. Conveyor Belt Tracking at Center Drive... 9 Spindle Removal... 9 A - Center Drive Spindle Removal... 0 B - Idler Spindle Removal... C - 0.5" Nose Bar Idler Spindle Removal... D - Nose Bar Idler Spindle Removal... E -.875" Nose Bar Idler Spindle Removal... 5 Reassembling Tail Assemblies... 6 Gas Assist Replacement... 6 Bearing Replacement... 7 Standard Bearings " and " Nose Bar Return Spindle Bearings... 7 " Nose Bar Bearings " Nose Bar Bearings... 8 Center Drive Tension Spindle Bearings... 8 Notes... 9 Service Parts... 0 Center Drive Assembly Components... 0 Idler End Components....5" Nose Bar Idler End... " Nose Bar Idler End " Nose Bar Idler End... 6 Discharge End " Nose Bar Discharge End... 8 " Nose Bar Discharge End " Nose Bar Discharge End... Conveyor Frame and Extensions with Standard Wear Strips... Wear Strips with Stainless Steel Sheet Bed Plate... Lifters... 5 Mounting Block... 5 Gas Assisted Tip Up... 5 " High Sides... 6 Adjustable Guiding... 7 Tool-Less Adjustable Guiding... 8 Hinged Guides... 9 Adjustable Hinged Guides Tool-Less Adjustable Hinged Guides... 5 Flat Belt Returns... 5 Scraper... 5 Opposed (Thru Beam) Photo Eye Mount... 5 Reflective Photo Eye Mount... 5 Reflective Photo Eye Kit... 5 Configuring Conveyor Belt Part Number Flat Belt Part Number Configuration Return Policy The Dorner Limited Warranty applies. Dorner has convenient, pre-configured kits of Key Service Parts for all conveyor products. These time saving kits are easy to order, designed for fast installation, and guarantee you will have what you need when you need it. Key Parts and Kits are marked in the Service Parts section of this manual with the Performance Parts Kits logo. Dorner 7600 series conveyors are covered by Patent Numbers 7,6,697, 7,07,5, 7,59,5 B, 7,68,79 B, 7,8,9, 8,0,68 B and corresponding patents and patent applications in other countries. Dorner reserves the right to make changes at any time without notice or obligation. Dorner Mfg. Corp Rev. B

3 Warnings General Safety DANGER WARNING SEVERE HAZARD! KEEP OFF CONVEYORS. Climbing, sitting, walking or riding on conveyor will result in death or serious injury. DANGER SEVERE HAZARD! LOCK OUT POWER before removing guards or performing maintenance. Exposed moving parts can cause serious injury. WARNING EXPLOSION HAZARD! DO NOT OPERATE CONVEYORS IN AN EXPLOSIVE ENVIRONMENT. The electric gearmotor generates heat and could ignite combustible vapors. Failure to comply will result in death or serious injury. BURN HAZARD! DO NOT TOUCH the motor while operating, or shortly after being turned off. Motors may be HOT and can cause serious burn injuries. WARNING WARNING CRUSH HAZARD! DO NOT place hands or fingers inside the conveyor while it is running. DO NOT wear loose garments while operating the conveyor. Loose garments can become caught up in the conveyor. Failure to comply could result in serious injury. WARNING CRUSH HAZARD! SUPPORT CONVEYOR SECTIONS PRIOR TO LOOSENING STAND HEIGHT OR ANGLE ADJUSTMENT SCREWS. Loosening stand height or angle adjustment screws may cause conveyor sections to drop down, causing serious injury. PUNCTURE HAZARD! Handle drive shaft keyway with care. It may be sharp and could puncture the skin, causing serious injury. WARNING SEVERE HAZARD! Dorner cannot control the physical installation and application of conveyors. Taking protective measures is the responsibility of the user. When conveyors are used in conjunction with other equipment or as part of a multiple conveyor system, CHECK FOR POTENTIAL PINCH POINTS and other mechanical hazards before system startup. Failure to comply could result in serious injury Rev. B Dorner Mfg. Corp.

4 Product Description Refer to (Figure ) for typical conveyor components. Conveyor Gearmotor Figure 6 Belt (Flat Belt Shown) Support Stands 5 Motor Controller 6 Discharge End 7 Infeed End 8 Center Drive Module Figure Specifications Flat Belt 7600 Series Center Drive Conveyor 7 6 M WW LLL S S C D G BB Belt Type Profile Tail Types / Position Cleaning Options Idler Stand Location Drive Stand Location Conveyor Length Conveyor Width Document Language Bed Type / V-Guide Dorner Mfg. Corp Rev. B

5 Specifications Conveyor Supports Figure Maximum Distances: = Support Stand on Infeed End = ft (9 mm) = Between Support Stands = 8 ft (8 mm)** = Support Stand on Discharge End = ft (9 mm) ** For conveyors longer than 0 ft (.05 m), install support at frame joint. Specifications Conveyor Width Reference (WW) Conveyor Belt Width Maximum Conveyor Load Belt Travel Maximum Belt Speed Belt Take-up Conveyor Length Reference (LLL) Conveyor Length Figure in 0 increments 6" (5 mm) - 60" (5 mm) in " (5 mm) increments 00 lbs. (8 kg).5" (86 mm) per revolution of pulley 5 ft/minute (00 m/minute).5" (8 mm) in 00 increments 8" (9 mm) - 80" (9 mm) in " (5 mm) increments IMPORTANT Maximum conveyor loads are based on: Non-accumulating product Product moving toward gearmotor Conveyor being mounted horizontally Conveyor being located in a dry environment Conveyor equipped with standard belt only Rev. B 5 Dorner Mfg. Corp.

6 Installation Figure CAUTION Dorner recommends cleaning all the food zones prior to placing conveyor into service. Ensure adequate access is provided for cleaning and servicing equipment so that the required level of hygiene can be maintained. CAUTION Conveyor MUST be mounted straight, flat, and level within confines of conveyor. Use a level (Figure, item ) during setup. Conveyors Longer than 0 ft (08 mm) Connecting Components Typical Connection Components (Figure ) Figure M0 x.5 mm hex head cap screws (x) Connector hex rods (x) Conveyor frames Figure Required Tools Figure. Locate and arrange conveyor sections by section labels (Figure 5, item ). Figure 5 Level Torque wrench Recommended Installation Sequence. Assemble the conveyor (if required). Refer to All Conveyors on page 0.. Attach the stands. Refer to Stand Installation on page.. Install the gearmotor. Refer to Drive Package Installation on page. Figure 5. Position the frame sections in the correct order. Dorner Mfg. Corp Rev. B

7 Installation. Connect the frame sections by bolting the hex post connectors (Figure 6, item ) to the sections of frame.. Make sure the slots in the wear strips (Figure 8, item ) line up properly with the frame slots (Figure 8, item ). Figure 6 Stainless Steel Sheet Bed Plates (optional) Typical Stainless Steel Sheet Bed Plates (Figure 9) Figure 9 Bed Plates Wear Strips Figure 6 Wear Strip Installation Standard Wear Strips Typical Standard Wear Strips (Figure 7) Wear Strips Figure 7 Figure 9. Attach the wear strips to the frame. Refer to Standard Wear Strips on page 7.. Place the sheet bed plates (Figure 0, item ) over the wear strips (Figure 0, item ). Figure 0 Figure 7. Position the wear strips (Figure 8, item ) on the frame. Figure 8 Figure 0 Figure Rev. B 7 Dorner Mfg. Corp.

8 Installation Lifter Installation Typical Lifter Components (Figure ) Belt Installation Typical Standard Belt (Figure ) Belt lift pivot bar Lifter bars Belt lift handle M8 -.5 x 6 mm hex head cap screw Figure Belt Figure Figure. Slide the belt lift pivot bar (Figure, item ) through the designated holes in the frame. The pins on the belt lift pivot bar should be located inside the frame side rails. Figure. Place the idler tail (Figure, item ) in the up position. Figure Figure Figure. Remove the pull pins (Figure 5, item ) from the center drive side plate (Figure 5, item ). Figure 5 Figure. Attach the lifter bars (Figure, item ) to the belt lift pivot bar (Figure, item ). Make sure the hooked ends of the lifter bars are facing down when resting against the frame.. Attach the lifter handle (Figure, item ) to the belt lift pivot rod. Figure 5 Dorner Mfg. Corp Rev. B

9 Installation. Lift up on the center drive guard (Figure 6, item ) and remove it. Figure 6 6. Lower the quick release arm (Figure 8, item ) on one of the stands. Note: if the conveyor is not equipped with Quick Release (QR Type) stands, it will be necessary to remove the entire stand. For detailed instructions, refer to the Sanitary Support Stands Installation, Maintenance and Parts Manual. Figure 8 Figure 6. Slide the tension spindle assembly (Figure 7, item ) out of the housing. Figure 7 Figure 8 7. Slide the belt (Figure 9, item ) on over the conveyor frame (Figure 9, item ). Figure 9 Figure 7 5. Repeat steps - on the other side of the drive assembly. WARNING SEVERE HAZARD! ONLY DISCONNECT ONE PIVOT BRACKET AT A TIME AND ONLY IF THE STANDS ARE BOLTED TO THE FLOOR. Disconnecting more than one pivot bracket at a time or not bolting the stands to the floor can cause the conveyor to tip and may result in serious injury. Figure 9 8. Secure the quick release arm on the stand and repeat steps 6 and 7 until the belt is around the entire length of the conveyor. 9. Slide the tension spindle assemblies (Figure 7, item ) back into the housing. 0. Reattach the center drive guards (Figure 6, item ).. Insert the pull pins (Figure 5, item ).. Add tension to the belt by lowering the tip-up tail or by sliding the idler tail out and tightening the nuts. Refer to Conveyor Belt Tensioning on page 7.. Adjust the belt tracking as necessary. Refer to Conveyor Belt Tracking on page Rev. B 9 Dorner Mfg. Corp.

10 Installation Guide Installation Typical Guide Components (Figure 0) Guide Pull pin Figure 0 All Conveyors Belt Return Installation Flat Belt Typical Flat Belt Components (Figure ) Figure Flat belt returns Figure 0. Position the guide (Figure, item ) so that the flat surface is facing the belt and then slide the guide onto the frame rail (Figure, item ). Figure Figure. Slide the return shaft (Figure, item ) up and through the large slot (Figure, item ) in the frame. Figure Figure. Line up the guide holes with the holes in the frame.. Insert the pull pins (Figure, item ) into the holes in the guide (Figure, item ). Figure. Push up on the return shaft (Figure 5, item ) and slide the notched end of the shaft through the small slot (Figure 5, item ) on the opposite side of the frame. Figure 5 Figure Figure Figure 5. Repeat the procedure for all other belt returns. Dorner Mfg. Corp Rev. B

11 Scraper Installation Typical Scraper Components (Figure 6) Scraper adjust plate Scraper shaft Scraper bar holder UHMW scraper 5 Scraper mount plate 6 Pull pin 7 Handle 8 M0-.50 hex head cap screws (x) Figure 6 Installation. Insert the notched end of the scraper shaft (Figure 8, item ) so that it is situated within the groove in the mounting plate (Figure 8, item ). Figure Figure 8. Attach the scraper bar holders (Figure 9, item ) to the scraper shaft (Figure 9, item ). Figure 9 8 Figure 6. Attach the scraper adjust plate (Figure 6, item ) and the scraper mount plate (Figure 6, item 5) to the frame using four M0-.5 x mm hex head cap screws.. Slide the notched end of the scraper shaft (Figure 7, item ) through the adjustment plate (Figure 7, item ). Figure 7 7 Figure 9 5. Attach the UWHM scraper (Figure 9, item ) to the scraper bar holders (Figure 9, item ). 6. Insert the pin (Figure 0, item ) to lock the scraper bar in place (Figure 0, item ). Figure 0 Figure 7 Figure Rev. B Dorner Mfg. Corp.

12 Installation 7. Adjust the scraper to the desired position using the scraper bar handle (Figure 0, item ). Figure CAUTION Apply minimal pressure between the scraper (Figure, item ) and the belt (Figure, item ). Positioning the scraper so that it is digging into the belt will increase resistance, cause unnecessary strain on the motor and lead to premature belt failure. Stand Installation Typical Stand Components (Figure ) Conveyor Stand Knob M0-.50 x mm hex head cap screws (x) Figure Figure 8. Secure the scraper by tightening the handle (Figure, item ). Figure Figure. Properly support the conveyor.. Attach the non-quick release side of the stand (Figure, item ) to the MOTOR SIDE of the conveyor (Figure, item ) using two M0-.5 x mm hex head cap screws (Figure, item ). Figure Figure Figure. Attach the quick-release arm to the stand with the knob. (Figure, item ). For detailed assembly instructions, refer to the Sanitary Support Stands Installation, Maintenance and Parts Manual. Dorner Mfg. Corp Rev. B

13 Installation Drive Package Installation Typical Motor Components (Figure 5) End drive package Motor Mounting Block Installation. Clamp mounting block (Figure 7, item ) to frame (Figure 7, item ).. Tighten bolt to 0 in-lb ( Nm) (Figure 7, item ) to secure. Figure 7 Figure 5 Figure 5. Attach the motor (Figure 6, item ) to the gear reducer (Figure 6, item ). Figure 7 Figure 6 CAUTION Do not overtighten bolt. Over tightening may cause the mounting block to deform. Figure 6 For detailed assembly instructions, refer to the 7600 Series Center Drive Packages Installation, Maintenance and Parts Manual Rev. B Dorner Mfg. Corp.

14 Preventive Maintenance and Adjustment Required Tools 8 mm wrench (or adjustable wrench) 0 mm wrench 7 mm wrench mm wrench /8" hex wrench (for bearing shaft assembly fasteners) mm hex wrench Standard Conveyors. Remove the guides, if applicable, by removing the pull pins (Figure 8, item ) that connect the guide (Figure 8, item ) to the frame. Figure 8 Checklist Keep service parts on hand. Refer to the "Service Parts" section starting on page 0 for recommendations. Replace any worn or damaged parts. Cleaning NOTE Proper conveyor application, cleaning, and sanitation are the responsibility of the end user. Figure 8. Place the tip up tail (Figure 9, item ) in the up position. Figure 9 CAUTION Dorner recommends cleaning all the food zones prior to placing conveyor into service. Ensure adequate access is provided for cleaning and servicing equipment so that the required level of hygiene can be maintained. Routine Cleaning WARNING Figure 9. Lift up on the belt (Figure 9, item ). SEVERE HAZARD! LOCK OUT POWER before removing guards or performing maintenance. Exposed moving parts can cause serious injury. Dorner recommends cleaning the inside and the outside of the conveyor on a daily basis. Refer to the following steps to access the inside of the conveyor. Dorner Mfg. Corp Rev. B

15 Preventive Maintenance and Adjustment Conveyors with Lifters. Remove the guides, if applicable, by removing the pull pins (Figure 8, item ) that connect the guide (Figure 8, item ) to the frame.. Place the tip up tail in the up position.. Use the lifter handle (Figure 0, item ) to raise the belt (Figure 0, item ).. Add grease to the bearing using the zerk fitting (Figure, item ) on the exterior of the bearing shaft assembly. Figure Figure 0 Figure. Replace the bearings if they become worn. Periodic Cleaning Figure 0 Dorner recommends complete disassembly of the conveyor periodically for thorough cleaning. For conveyor disassembly and reassembly instructions: Refer to Conveyor Belt Replacement on page 6. Refer to Spindle Removal on page 9. Lubrication Conveyor Bearings CAUTION DO NOT submerge or soak bearing assemblies. This will reduce the life of the bearing. Conveyor bearing lubrication is required. Dorner recommends using an H- food grade grease. NOTE Although bearings are sealed, re-greasing is recommended to increase bearing life. An H- food grade grease is recommended. The frequency of bearing re-greasing is dependent upon the application in which the conveyor is being used. Frequency of regreasing will increase with the frequency of conveyor washing. Wearstrips and Belt Returns Replace the wearstrips and belt returns if they become worn. For wearstrip and belt return installation instructions: Refer to Wear Strip Installation on page 7. Refer to Belt Return Installation on page 0. Scraper Replace the UHMW scraper if it becomes worn. Refer to Scraper Installation on page for scraper installation instructions. Maintaining the Conveyor Belt Troubleshooting Inspect conveyor belt for: Surface cuts or wear Damage to the belt, surface cuts and / or wear indicate: Sharp or heavy parts impacting belt Jammed parts Accumulated dirt Foreign material inside the conveyor Improperly positioned accessories Excessive load on belt Dirt impacted on spindle Excessive or improper side loading Improper tracking Skipping indicates: Excessive load on belt Worn spindle or impacted dirt on drive spindle Improper tracking Rev. B 5 Dorner Mfg. Corp.

16 Preventive Maintenance and Adjustment Conveyor Belt Replacement WARNING Standard Belts. Place the idler tail (Figure, item ) in the up position. Figure SEVERE HAZARD! LOCK OUT POWER before removing guards or performing maintenance. Exposed moving parts can cause serious injury. Conveyors with Guides. Remove the pull pins (Figure, item ) that connect the guide (Figure, item ) to the frame. Figure Figure. Remove the pull pins (Figure 5, item ) from the center drive side plate (Figure 5, item ). Figure 5 Figure. Remove the guide (Figure, item ) from the conveyor (Figure, item ). Figure Figure 5. Lift up on the center drive guard (Figure 6, item ) and remove it. Figure 6 Figure Figure 6 Dorner Mfg. Corp Rev. B

17 Preventive Maintenance and Adjustment. Slide the tension spindle assembly (Figure 7, item ) out of the housing. 7. Slide the old belt (Figure 9, item ) off the conveyor frame (Figure 9, item ). Figure 7 Figure 9 Figure 7 5. Repeat steps - on the other side of the drive assembly. WARNING Figure 9 8. Secure the quick release arm on the stand and repeat steps 6 and 7 until the entire belt is off the conveyor. 9. Replace the old belt with a new one. Refer to Belt Installation on page 8. Conveyor Belt Tensioning SEVERE HAZARD! ONLY DISCONNECT ONE PIVOT BRACKET AT A TIME AND ONLY IF THE STANDS ARE BOLTED TO THE FLOOR. Disconnecting more than one pivot bracket at a time or not bolting the stands to the floor can cause the conveyor to tip and may result in serious injury. 6. Lower the quick release arm (Figure 8, item ) on one of the stands. Note: if the conveyor is not equipped with Quick Release (QR Type) stands, it will be necessary to remove the entire stand. For detailed instructions, refer to the Sanitary Support Stands Installation, Maintenance and Parts Manual. WARNING SEVERE HAZARD! LOCK OUT POWER before removing guards or performing maintenance. Exposed moving parts can cause serious injury. CAUTION Over-tensioning of conveyor may stretch conveyor belt and reduce bearing life. Figure 8 Figure Rev. B 7 Dorner Mfg. Corp.

18 Preventive Maintenance and Adjustment. Loosen the back nuts (Figure 50, item ) on both sides of the idler tail shaft. Figure 50 Figure 50. Turn the front nuts closest to the tail (Figure 5, item ) clockwise in order to increase tension on the belt. Figure 5 Conveyor Belt Tracking Tracking Procedure IMPORTANT When installing a new belt, set conveyor tracking elements to the zero position and start the tracking procedure. The zero position is when the tails are tensioned out to the 6 dimension as shown in (Figure 5, and the infeed tension roller (Figure 55, item ) on the center drive assembly is set to its outermost position (roller away from center of box, against guard). Inspect belt tracking at tails and at center drive assembly. Track belt where needed. Refer to Conveyor Belt Tracking at Tails on page 8 and Conveyor Belt Tracking at Center Drive on page 9. For conveyors 6 ft long and under, the majority of the belt tracking will be accomplished at the center drive assembly (may be able to track belt without tracking the tails). Figure 5 Conveyor Belt Tracking at Tails To adjust conveyor belt tracking at the tails:. Loosen the back nut (Figure 5, item ) on the idler tail shaft that needs to be adjusted.. Tighten the front nut (Figure 5, item ) on the idler tail shaft to adjust the belt tracking. CAUTION Ensure that there is at least 6" (5 mm) from the frame to the end of the tail. CAUTION Ensure that there is at least 6" (5 mm) from the frame to the end of the tail. Figure 5 a. Loosen the nut to shorten the length of the idler tail shaft and bring the belt closer to that side of the conveyor (Figure 5). Figure 5 Figure 5. Tighten the back nuts (Figure 5, item ) to secure the tail. Figure 5 Dorner Mfg. Corp Rev. B

19 Preventive Maintenance and Adjustment b. Tighten the nut to increase the length of the idler tail shaft and move the belt away from that side of the conveyor (Figure 5). Figure 56 Figure 5 Figure 5. Tighten the back nut on the idler tail shaft when finished. Conveyor Belt Tracking at Center Drive Figure 55 Figure 56. Tighten the guide plate bolt (Figure 56, item ) to move the belt away from that side of the conveyor.. Tighten the guide plate nuts when finished. Spindle Removal IMPORTANT Belt tracking will need to be readjusted if the direction of travel is changed. WARNING SEVERE HAZARD! LOCK OUT POWER before removing guards or performing maintenance. Exposed moving parts can cause serious injury. Figure 55 Tracking of belt through the center drive is done by adjusting the position of the infeed roller (Figure 55, item ) on the center drive assembly. To adjust conveyor belt tracking at the center drive:. Loosen the guide plate nuts (Figure 56, item ) on the infeed side of the center drive assembly.. Remove the conveyor belt to access the spindles. Refer to Conveyor Belt Replacement on page 6.. Remove the spindle by following the instructions for the specific spindle type: A - Center Drive Spindle Removal B - Idler Spindle Removal C - 0.5" Nose Bar Idler Spindle Removal D - " Nose Bar Idler Spindle Removal E -.875" Nose Bar Idler Spindle Removal Rev. B 9 Dorner Mfg. Corp.

20 Preventive Maintenance and Adjustment A - Center Drive Spindle Removal WARNING Figure 59 PUNCTURE HAZARD! Handle drive shaft keyway with care. It may be sharp and could puncture the skin, causing serious injury.. Place the idler tail (Figure 57, item ) in the up position. Figure 57 Figure 59. Slide the tension spindle assembly (Figure 60, item ) out of the housing. Figure 60 Figure 57. Remove the pull pins (Figure 58, item ) from the center drive side plate (Figure 58, item ). Figure 58 Figure Repeat steps - on the other side of the drive assembly. WARNING Figure 58. Lift up on the center drive guard (Figure 59, item ) and remove it. CRUSH HAZARD! SUPPORT MOTOR PRIOR TO LOOSENING THE BOLTS. Loosening motor bolts may cause it to drop down, causing serious injury. 6. Remove the bolts (Figure 6, item ) that connect the motor (Figure 6, item ) to the gear reducer (Figure 6, item ). Dorner Mfg. Corp Rev. B

21 Preventive Maintenance and Adjustment Figure 6 Figure 6 Figure 6 7. Disconnect the motor (Figure 6, item ) from the gear reducer (Figure 6, item ). Figure 6 Figure 6 9. Use a mm hex wrench to loosen the outside button head screws (Figure 6, item ) and the inside button head screws (Figure 6, item ) that connect the gearmotor to the drive spindle. Figure 6 Figure 6 8. Remove the drive spindle cover (Figure 6, item ). Figure Rev. B Dorner Mfg. Corp.

22 Preventive Maintenance and Adjustment 0. Remove the bolts (Figure 65, item ) that connect the bent bars (Figure 65, item ) to the drive mounting bracket (Figure 65, item ).. Use a mm hex wrench to loosen the button head screws on the bearing (Figure 68, item ). Figure 68 Figure 65 Figure 65. Slide the gear reducer (Figure 66, item ) off the drive shaft (Figure 66, item ). Figure 68. Remove the bolt (Figure 69, item ) that connects the drive shaft assembly (Figure 69, item ) to the block shaft mount (Figure 69, item ). Figure 69 Figure 66 Figure 66. Remove the bearing cover (Figure 67, item ) on the center drive shaft assembly (Figure 67, item ). Figure Lower the end of the drive shaft spindle (Figure 70, item ) until it is clear of the side plate (Figure 70, item ) and remove it. Figure 70 Figure 67 Figure 67 Figure 70 Dorner Mfg. Corp Rev. B

23 Preventive Maintenance and Adjustment B - Idler Spindle Removal. Remove the back nuts (Figure 7, item ) on both idler tail shafts. C - 0.5" Nose Bar Idler Spindle Removal. Remove the back nuts (Figure 7, item ) on both discharge nose bar shafts. Figure 7 Figure 7 Figure 7. Slide the idler tail assembly (Figure 7, item ) out of the take up blocks (Figure 7, item ).. Remove the bearing covers (Figure 7, item ).. Use a mm hex wrench (Figure 7, item ) to loosen the bearing shaft assembly fasteners (Figure 7, item ). Figure 7 Figure 7. Slide the nose bar tail assembly (Figure 75, item ) out of the take up blocks (Figure 75, item ). Figure 75 Figure 7 5. Remove the bearing shafts (Figure 7, item ) and both pinch guards (Figure 7, item ). Figure 75. Slide the nose bar shafts (Figure 76, item ) off of the nose bar weldment (Figure 76, item ). Figure 76 Figure 7 Figure 7 Figure Rev. B Dorner Mfg. Corp.

24 Preventive Maintenance and Adjustment. Use a 0 mm wrench to remove one of the acorn nuts (Figure 77, item ) from the nose bar shaft. Figure 77 D - Nose Bar Idler Spindle Removal. Remove the back nuts (Figure 80, item ) on both discharge nose bar shafts. Figure 80 Figure Remove the nose bar shaft (Figure 78, item ), the rollers (Figure 78, item ) and the roller mounts (Figure 78, item ). Figure 80. Slide the nose bar tail assembly (Figure 8, item ) out of the take up blocks (Figure 8, item ). Figure 8 Figure 78 Figure Remove the nose bar return spindle (Figure 79, item ). Figure 79 Figure 8. Slide the nose bar shafts (Figure 8, item ) off of the nose bar weldment (Figure 8, item ). Figure 8 Figure 79 Figure 8 Dorner Mfg. Corp Rev. B

25 Preventive Maintenance and Adjustment. Use a 7 mm wrench to remove both pilot nose bolts (Figure 8, item ) from the nose bar weldment (Figure 8, item ). Figure 8 E -.875" Nose Bar Idler Spindle Removal. Slide the pinch guard blocks (Figure 86, item ) off the nose bar spindles (Figure 86, item ). Figure 86 Figure 8 5. Slide the nose bar puck holders (Figure 8, item ) and the nose bar spindle (Figure 8, item ) off of the nose bar weldment (Figure 8, item ). Figure 86. Remove the transfer bearing screws (Figure 87, item ) and the cover (Figure 87, item ) using an 8 mm wrench. Figure 87 Figure 8 Figure 8 6. Remove the nose bar return spindle (Figure 85, item ). Figure 85 Figure 87. Remove the back nuts (Figure 88, item ) on both discharge nose bar shafts. Figure 88 Figure 85 Figure Rev. B 5 Dorner Mfg. Corp.

26 Preventive Maintenance and Adjustment. Slide the nose bar tail assembly (Figure 89, item ) out of the take up blocks (Figure 89, item ). Figure 89 Reassembling Tail Assemblies Refer to the "Service Parts" section starting on page 0 for complete diagrams and lists of all tail assembly components. Gas Assist Replacement. Raise the tip up tail.. Remove the pull pin (Figure 9, item ). Figure 9 Figure Use a mm hex wrench to loosen all the bearing fasteners (Figure 90, item ). Figure 90 Figure 9. Remove the hex bolt (Figure 9, item ) that connects the gas spring (Figure 9, item ) to the gas spring standoff post (Figure 9, item ). Figure 9 Figure Slide the nose bar shafts (Figure 9, item ) off the nose bar spindles (Figure 9, item ). Figure 9 Figure 9. Remove the inside hex bolt that connects the standoff post (Figure 9, item ) to the frame. Figure 9 Dorner Mfg. Corp Rev. B

27 Preventive Maintenance and Adjustment Bearing Replacement Standard Bearings. Secure the bearing shaft.. Remove the bearing cover.. Insert the rod end of another bearing shaft through the bearing orifice (Figure 9)..5" and " Nose Bar Return Spindle Bearings. Remove the nose bar return spindle. Refer to "Spindle Removal" starting on page 9.. Using a bearing removal tool (Figure 96, item ), remove the bearing (Figure 96, item ). Figure 96 Figure 9 Figure 9. Apply lateral pressure to the rod until the bearing comes loose. 5. Remove the worn or damaged bearing (Figure 95). Figure 95. Replace the bearing. Figure 96 " Nose Bar Bearings. Remove the nose bar spindle. Refer to "Spindle Removal" starting on page 9.. Remove the nose bar puck holders (Figure 97, item ). Figure Replace the bearing. Figure 95 NOTE When inserting the new bearing, make sure the anti-rotation notch (Figure 95, item ) on the bearing lines up with the groove inside the housing (Figure 95, item ). Figure 97. Using a bearing removal tool (Figure 98, item ) remove the bearing (Figure 98, item ). Figure Use a hex wrench to tighten the bearing shaft assembly fasteners to 5 in-lbs (6 N m). Check after hours of conveyor use.. Replace the bearing. Figure Rev. B 7 Dorner Mfg. Corp.

28 Preventive Maintenance and Adjustment.875" Nose Bar Bearings. Remove the nose bar spindle. Refer to "Spindle Removal" starting on page 9.. Remove the bearing (Figure 99, item ) from the nose bar shaft assembly (Figure 99, item ). Figure 99. Slide the housing block (Figure 0, item ) and bearing off of the tension spindle (Figure 0, item ). Figure 0. Replace the bearing. Figure 99 Center Drive Tension Spindle Bearings. Remove the tension spindle. Refer to steps - 5 in A - Center Drive Spindle Removal on page 0.. Remove the bearing cover (Figure 00, item ). Figure 0 5. Remove the bearing (Figure 0, item ) from the housing block (Figure 0, item ). Figure 0 Figure 00 Figure 0 Figure 00. Use a mm hex wrench to remove the button head screws that connect the bearing to the spindle (Figure 0, item ). Figure 0 Figure 0 Dorner Mfg. Corp Rev. B

29 NOTES Rev. B 9 Dorner Mfg. Corp.

30 Service Parts Center Drive Assembly Components NOTE For replacement parts other than those shown in this section, contact an authorized Dorner Service Center or the factory. Key Service Parts and Kits are identified by the Performance Parts Kits logo. Dorner recommends keeping these parts on hand. 9 Center Drive Bearing Kit 0 Center Drive Assembly Bearing Cover Center Drive Housing Block Zerk Fitting 96055MSS Hex Head Cap Screw, M0-.50 x 55 mm MSS Hex Head Cap Screw, M0-.50 x 0 mm Center Drive Block Shaft Mount 7 * Center Drive Shaft Assembly, with Bearing and Cover Center Drive Side Plate Pull Pin MSS Hex Head Cap Screw, M0-.50 x 5 mm 99009MSS Hex Nut 509WW Infeed Center Drive Guard Assembly 5095WW Center Drive Tension Spindle 80-6 Bearing WW Center Drive Spindle 59WW CE Center Drive Spindle MSS Hex Head Cap Screw, M0-.50 x 6 mm 7 55WW Center Drive Cross Member Post 8 59WW Outfeed Center Drive Guard Assembly 9 76CDD Center Drive Bearing Kit when Conveyor is ordered with a Dorner Gearmotor Mounting Package (Includes Items and ) 76CDC Center Drive Bearing Kit when Conveyor is ordered without a Dorner Gearmotor Mounting Package (Includes Items and ) 0 57WW Center Drive Module (Includes items through 8) 50WW CE Center Drive Module (Includes items through 8) WW = Conveyor width ref: in 0 increments * When the conveyor is ordered with a Dorner gearmotor mounting package a shaft assembly is replaced with a gearmotor mounting bracket. Dorner Mfg. Corp Rev. B

31 Service Parts Idler End Components 5 Idler Tail Kit Bearing Kit Shaft Assembly, with Bearing and Cover Nut 50WW Idler Spindle 5069 Pinch Guard, Left Hand Pinch Guard, Right Hand WW Pinch Shaft Guard Key Stop Tip Up Knob Bearing Bearing Cover 57 Spacer WW Tip Up Shaft 96060MSS Hex Head Cap Screw, M6-.00 x 0 mm 76BKX-WW Bearing Kit (Includes Items 9 and 0) 5 76STX-WW Idler Tail Kit (Includes Items through 6) WW = Conveyor width ref: in 0 increments Rev. B Dorner Mfg. Corp.

32 Service Parts.5" Nose Bar Idler End 6.5 Nose Bar Kit 7.5 Idler Spindle Kit 8.5 Idler Tail Kit " Nose Bar Shaft Assembly Nut Roller, 0.5" x.06" Roller, 0.5" x.7" MSS Acorn Nut WW Nose Bar Shaft 7 See Chart Roller Mount Return Spindle Bearing WW 0.5" Nose Bar Return Spindle 0 509WW 0.5" Nose Bar Weldment Assembly Key Stop 5068 Tip Up Knob 57 Spacer WW Tip Up Shaft MSS Hex Head Cap Screw, M6-.00 x 0 mm 6 76NB5-WW 0.5" Nose Bar Kit (Includes Items through 7) 7 76NB-WW 0.5" Idler Spindle Kit (Includes Items through 9) 8 76NBT-WW 0.5" Idler Tail Kit (Includes Items through 0) WW = Conveyor width ref: in 0 increments Dorner Mfg. Corp Rev. B

33 Service Parts Item 7: Roller Mount Width Part Number 6" (5 mm) " (0 mm) " (5 mm) & " (05 mm) & " (56 mm) & " (06 mm) (x) 8" (57 mm) 50077, & " (508 mm) (x) & " (559 mm) (x) & " (60 mm) (x) 6" (660 mm) (x), & " (7 mm) (x) & " (76 mm) (x) & " (8 mm) (x) " (86 mm) (x), & " (9 mm) (x) & " (965 mm) (x) & " (06 mm) (x5) " (067 mm) (x), & " (8 mm) (x5) & " (68 mm) (x5) & " (9 mm) (x6) 50" (70 mm) (x5), & " ( mm) (x6) & " (7 mm) (x6) & " ( mm) (x7) 58" (7 mm) (x6), & " (5 mm) (x7) & Rev. B Dorner Mfg. Corp.

34 Service Parts " Nose Bar Idler End 7 Idler Spindle Kit 8 Idler Tail Kit 9 Bearing Kit For Wide or Wider Conveyors " Nose Bar Shaft Assembly Nut 80-6 Return Spindle Bearing 507WW " Nose Bar Return Spindle Nose Bar Bearing 6 See Chart " Nose Bar Spindle Nose Bar Puck Holder Right Hand 8 505WW " Nose Bar Weldment Assembly Nose Bar Puck Holder Left Hand Pilot Nose Bolt Key Stop 5068 Tip Up Knob Nose Bar Puck Holder, Center 57 Spacer MSS Hex Head Cap Screw, M6-.00 x 0 mm WW Tip Up Shaft 7 76NB-WW " Idler Spindle Kit (Includes Items through 7, 9 and ) 8 76NBT-WW " Idler Tail Kit (Includes Items through 0 and ) 9 76BK-WW Bearing Kit (Includes Items and 5) WW = Conveyor width ref: in 0 increments Dorner Mfg. Corp Rev. B

35 Service Parts Item 6: Nose Bar Spindle Width Part Number 6" (5mm) " (0mm) " (5mm) " (05mm) 5050 " (56mm) 5050 (x) & " (06mm) 5050 (x) & " (57mm) 5050 (x) & " (508mm) 5050 (x) & 5050 " (559mm) 5050 (x) & " (60mm) 5050 (x) & " (660mm) 5050 (x) & " (7mm) 5050 (x) & " (76mm) (x) & " (8mm) (x) & " (86mm) (x) & " (9mm) (x) & " (965mm) 5050 (x) & " (06mm) 5050 (x) & " (067mm) 5050 (x) & " (8mm) 5050 (x) & " (68mm) (x) & " (9mm) (x) & " (70mm) (x) & " (mm) (x) & " (7mm) (x) & " (mm) (x) & " (7mm) (x) & " (5mm) (x) & Rev. B 5 Dorner Mfg. Corp.

36 Service Parts.875" Nose Bar Idler End Idler Spindle Kit Idler Tail Kit 8 Bearing Kit MSS Hex Head Cap Screw M5-0.8 x 0 mm Transfer Bearing Cover Grease Fitting " Nose Bar Shaft Assembly Right Hand Nut Bearing Pinch Guard block 8 50WW.875" Nose Bar Spindle " Nose Bar Shaft Assembly Left Hand Key Stop 5068 Tip Up Knob 57 Spacer 96060MSS Hex Head Cap Screw, M6-.00 x 0 mm WW Tip Up Shaft 5 50-WW Anti-Rotation Bar 6 76NB-WW.875" Idler Spindle Kit (Includes Items 6 through 8) 7 76NBT-WW.875" Idler Tail Kit (Includes Items through 9) 8 76BK-WW Bearing Kit (Includes Item 6) WW = Conveyor width ref: in 0 increments Dorner Mfg. Corp Rev. B

37 Service Parts Discharge End 9 Bearing Kit 0 Discharge Tail Kit Nut 5069 Pinch Guard Left Hand 5069 Pinch Guard Right Hand WW Pinch Guard Shaft Discharge Shaft Assembly, with Bearing and Cover 6 50WW Idler Spindle Bearing Cover 9 76BK Bearing Kit (Includes Items 7 and 8) 0 76SDX-WW Discharge Tail Kit (Includes Items through 8) WW = Conveyor width ref: in 0 increments Rev. B 7 Dorner Mfg. Corp.

38 Service Parts.5" Nose Bar Discharge End.5 Nose Bar Discharge Kit.5 Spindle Discharge Kit.5 Discharge Tail Kit Discharge Nose Bar Shaft Assembly Nut Roller 0.5" x.06" Roller 0.5" x.7" MSS Acorn Nut WW Nose Bar Shaft 7 See Chart Roller Mount Return Spindle Bearing WW 0.5" Nose Bar Return Spindle 0 509WW 0.5" Nose Bar Weldment Assembly 76NB5-WW 0.5" Nose Bar Discharge Kit (Includes Items through 7) 76NB-WW 0.5" Spindle Discharge Kit (Included Items through 9) 76NBD5-WW 0.5" Discharge Tail Kit (Includes Items through 0) WW = Conveyor width ref: in 0 increments Dorner Mfg. Corp Rev. B

39 Service Parts Item 7: Roller Mount Width Part Number 6" (5 mm) " (0 mm) " (5 mm) & " (05 mm) & " (56 mm) & " (06 mm) (x) 8" (57 mm) 50077, & " (508 mm) (x) & " (559 mm) (x) & " (60 mm) (x) 6" (660 mm) (x), & " (7 mm) (x) & " (76 mm) (x) & " (8 mm) (x) " (86 mm) (x), & " (9 mm) (x) & " (965 mm) (x) & " (06 mm) (x5) " (067 mm) (x), & " (8 mm) (x5) & " (68 mm) (x5) & " (9 mm) (x6) 50" (70 mm) (x5), & " ( mm) (x6) & " (7 mm) (x6) & " ( mm) (x7) 58" (7 mm) (x6), & " (5 mm) (x7) & Rev. B 9 Dorner Mfg. Corp.

40 Service Parts " Nose Bar Discharge End Discharge Spindle Kit Discharge Tail Kit Bearing Kit For Wide or Wider Conveyors 5009 Discharge Nose Bar Shaft Assembly Nut 80-6 Return Spindle Bearing 507WW " Nose Bar Return Spindle Nose Bar Bearing 6 See Chart " Nose Bar Spindle Nose Bar Puck Holder, Right Hand 8 505WW " Nose Bar Weldment Assembly Nose Bar Puck Holder, Left Hand Pilot Nose Bolt Nose Bar Puck Holder, Center 76NB-WW " Discharge Spindle Kit (Includes Items through 7, 9 and ) 76NBD-WW " Discharge Tail Kit (Includes Items through ) 76BK-WW Bearing Kit (Includes Items and 5) WW = Conveyor width ref: in 0 increments Dorner Mfg. Corp Rev. B

41 Service Parts Item 6: Nose Bar Spindle Width Part Number 6" (5mm) " (0mm) " (5mm) " (05mm) 5050 " (56mm) 5050 (x) & " (06mm) 5050 (x) & " (57mm) 5050 (x) & " (508mm) 5050 (x) & 5050 " (559mm) 5050 (x) & " (60mm) 5050 (x) & " (660mm) 5050 (x) & " (7mm) 5050 (x) & " (76mm) (x) & " (8mm) (x) & " (86mm) (x) & " (9mm) (x) & " (965mm) 5050 (x) & " (06mm) 5050 (x) & " (067mm) 5050 (x) & " (8mm) 5050 (x) & " (68mm) (x) & " (9mm) (x) & " (70mm) (x) & " (mm) (x) & " (7mm) (x) & " (mm) (x) & " (7mm) (x) & " (5mm) (x) & Rev. B Dorner Mfg. Corp.

42 Service Parts.875" Nose Bar Discharge End.875 Discharge Spindle Kit.875 Discharge Tail Kit Bearing Kit MSS Hex Head Cap Screw M5-0.8 x 0mm Transfer Bearing Cover Grease Fitting " Discharge Nose Bar Shaft Assembly Right Hand Nut Bearing Pinch Guard block 8 50WW.875" Nose Bar Spindle " Discharge Nose Bar Shaft Assembly Left Hand 0 50-WW Anti-Rotation Bar 76NB-WW.875" Discharge Spindle Kit (Includes Items 6 through 8) 76NBD-WW.875" Discharge Tail Kit (Includes Items through 9) 76BK-WW Bearing Kit (Includes Item 6) WW = Conveyor width ref: in 0 increments Dorner Mfg. Corp Rev. B

43 Conveyor Frame and Extensions with Standard Wear Strips Service Parts Consult Factory for Frame Part Number LLL Wear Strip 5009 Hex Post Connector 9600MSS Hex Head Cap Screw M0-.5 x 0 mm LLL = Conveyor length ref: in 00 increments Rev. B Dorner Mfg. Corp.

44 Service Parts Wear Strips with Stainless Steel Sheet Bed Plate 5WW-LLL Bed Plate LLL Wear Strip WW = Conveyor width ref: in 0 increments LLL = Conveyor length ref: in 00 increments Dorner Mfg. Corp Rev. B

45 Lifters Gas Assisted Tip Up Service Parts WW Belt Lifter Shaft 5076 Belt Lifter 5009 Belt Lifter Handle 9608MSS Hex Head Cap Screw M8-.5 x mm WW = Conveyor width ref: in 0 increments Mounting Block Pin Gas Spring Gas Spring Clevis Gas Spring Eyelet Gas Spring Stand Off Post Tip Up Bushing Tip Up Knob Tip Up Knob Assembly Tip Up Shaft 0 57 Spacer 9606MSS Hex Head Cap Screw, M6-.00 x mm 96080MSS Hex Head Cap Screw, M8-.5 x 0 mm 9605MSS Hex Head Cap Screw, M0-.50 x 6 mm Key Stop WW = Conveyor width ref: 8-60 in 0 increments Mounting Block Washer Eyebolt, M0 x MSS Hex Head Cap Screw, M x 6 mm MSS Hex Nut, M Rev. B 5 Dorner Mfg. Corp.

46 Service Parts " High Sides For ' ' Conveyors For ' ' Conveyors For ' ' Conveyors Number of guiding sections increases every 0' LLLLL High Side Guide for Conveyors '-' Long LLLLL High Side Right Hand Guide for Conveyors over ' Long 5060-LLLLL High Side Guide for Conveyors '-' Long LLLLL High Side Right Hand Guide for Conveyors over ' Long 5050-LLLLL High Side Guide Square End Pull Pin LLLLL = Guide Length in inches with decimal places. Example: Guide Length = 95.5" LLLLL = 0955 Dorner Mfg. Corp Rev. B

47 Service Parts Adjustable Guiding Rail Clamp Washer Eye Bolt M0 x Mounting Bracket Vertical Post Assembly LLLLL Round Guide Rail Guide Post MSS Hex Head Cap Screw, M8 -.5 x mm MSS Hex Nut, M LLLLL = Length in inches with decimal places. Example: Guide Length = 95.5" LLLLL = Rev. B 7 Dorner Mfg. Corp.

48 Service Parts Tool-Less Adjustable Guiding Rail Clamp Handle Washer Eye Bolt M0 x Mounting Bracket Vertical Post Assembly LLLLL Round Guide Rail Guide Post MSS Hex Head Cap Screw, M8 -.5 x mm LLLLL = Length in inches with decimal places. Example: Guide Length = 95.5" LLLLL = 0955 Dorner Mfg. Corp Rev. B

49 Service Parts Hinged Guides Mounting Block Pivot Guide Mounting Bracket Guide Clamp Bracket PH-0800 Mounting Guide Shaft for " Guides PH-00 Mounting Guide Shaft for 6" Guides 5 57-LLLLL Guiding for " Guides LLLLL Guiding for 6" Guides Washer Eyebolt M0 x.50 mm Cotter Pin SS Weld Nut, M8 x.5 mm MSS Hex Head Cap Screw, M8 -.5 x 5 mm 9606MSS Hex Head Cap Screw, M x 6 mm 99008MSS Hex Nut, M mm LLLLL = Length in inches with decimal places. Example: Guide Length = 95.5" LLLLL = Rev. B 9 Dorner Mfg. Corp.

50 Service Parts Adjustable Hinged Guides Mounting Block Pivot Guide Bracket 500 Guide Post DH-00 Adjustable Guide Shaft LLLLL Guiding Clamp Rail Lanyard Pin Washer Eyebolt M0 x Cotter Pin 9608MSS Hex Head Cap Screw, M8 -.5 x mm 9606MSS Hex Head Cap Screw, M x 6 mm 9900MSS Hex Nut, M MSS Hex Nut, M mm LLLLL = Length in inches with decimal places. Example: Guide Length = 95.5" LLLLL = 0955 Dorner Mfg. Corp Rev. B

51 Service Parts Tool-Less Adjustable Hinged Guides Mounting Block Pivot Guide Bracket 500 Guide Post DH-00 Adjustable Guide Shaft LLLLL Guiding Clamp Rail Handle Lanyard Pin Washer Eyebolt M0 x Cotter Pin 9608MSS Hex Head Cap Screw, M8 -.5 x mm 9606MSS Hex Head Cap Screw, M x 6 mm LLLLL = Length in inches with decimal places. Example: Guide Length = 95.5" LLLLL = Rev. B 5 Dorner Mfg. Corp.

52 Service Parts Flat Belt Returns Scraper Return Kit Clamp Return Disk 508WW Return Shaft 76R-WW Return Kit (Includes Items and ) WW = Conveyor width ref: in 0 increments 960MSS Hex Head Cap Screw, M0-.50 x mm Scraper Adjust Plate 50WW Scraper Shaft Assembly Scraper Holder Bar 5 507WW Scraper Wear Bar Pull Pin Scraper Mount Plate Handle WW = Conveyor width ref: in 0 increments Dorner Mfg. Corp Rev. B

53 Service Parts Opposed (Thru Beam) Photo Eye Mount Mount Clamp Washer Eyebolt, M0 x Mounting Block NH-00 Mounting Shaft MSS Hex Head Cap Screw, M x 6 mm MSS Hex Nut, M Reflective Photo Eye Mount Reflector Mount Clamp Photo Eye Mount Clamp Washer Eyebolt, M0 x Reflector Mounting Block NH-00 Mounting Shaft MSS Hex Head Cap Screw, M x 6 mm MSS Hex Nut, M Rev. B 5 Dorner Mfg. Corp.

54 Service Parts Reflective Photo Eye Kit Reflector Mount Clamp Photo Eye Mount Clamp Washer Eyebolt, M0 x Reflector Photo Eye Sensor Mounting Block NH-00 Mounting Shaft MSS Hex Head Cap Screw, M x 6 mm MSS Hex Nut, M Dorner Mfg. Corp Rev. B

55 Configuring Conveyor Belt Part Number Service Parts Figure 0 76M WW-LLL SS C D G BB FLAT BELT Figure 0 Flat Belt Part Number Configuration Refer to model number on the conveyor frame (Figure 0. From the model number determine the conveyor width (WW), length (LLL), drive/tail types (A) and belt type (BB). Use data to configure belt part number as indicated below. *Add V for v-guided belts Rev. B 55 Dorner Mfg. Corp.

56 Return Policy Returns must have prior written factory authorization or they will not be accepted. Items that are returned to Dorner without authorization will not be credited nor returned to the original sender. When calling for authorization, please have the following information ready for the Dorner factory representative or your local distributor:. Name and address of customer.. Dorner part number(s) of item(s) being returned.. Reason for return.. Customer's original order number used when ordering the item(s). 5. Dorner or distributor invoice number (if available, part serial number). A representative will discuss action to be taken on the returned items and provide a Returned Goods Authorization (RMA) number for reference. RMA will automatically close 0 days after being issued. To get credit, items must be new and undamaged. There will be a return charge on all items returned for credit, where Dorner was not at fault. It is the customer s responsibility to prevent damage during return shipping. Damaged or modified items will not be accepted. The customer is responsible for return freight. Conveyors and conveyor accessories Standard catalog conveyors 0% MPB, 700, 700 Series, cleated and specialty belt 50% AquaGard & AquaPruf Series conveyors non-returnable items Engineered to order products case by case Drives and accessories 0% Sanitary stand supports non-returnable items Parts Standard stock parts 0% Plastic chain, cleated and specialty belts non-returnable items Returns will not be accepted after 60 days from original invoice date. The return charge covers inspection, cleaning, disassembly, disposal and reissuing of components to inventory. If a replacement is needed prior to evaluation of returned item, a purchase order must be issued. Credit (if any) is issued only after return and evaluation is complete. Dorner has representatives throughout the world. Contact Dorner for the name of your local representative. Our Customer Service Team will gladly help with your questions on Dorner products. For a copy of Dorner's Warranty, contact factory, distributor, service center or visit our website at For replacement parts, contact an authorized Dorner Service Center or the factory. Dorner Mfg. Corp. reserves the right to change or discontinue products without notice. All products and services are covered in accordance with our standard warranty. All rights reserved. Dorner Mfg. Corp. 0 DORNER MFG. CORP. 975 Cottonwood Ave., PO Box 0 Hartland, WI USA TEL (USA) FAX (USA) Internet: Outside the USA: TEL FAX Rev. B Printed in U.S.A.