2200 Precision Move Dual Strand Conveyor

Transcription

1 00 Precision Move Dual Strand Conveyor Installation, Maintenance & Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box Cottonwood Ave. TEL: TEL: Hartland, WI USA FAX: FAX: Rev. A For other service manuals visit our website at:

2 Table of Contents Introduction... Warnings General Safety... 4 Product Description... 5 Specifications... 5 Models:... 5 Dual Strand Conveyor... 5 Support Stands... 5 Conveyor Supports:... 5 Maximum Distances:... 5 Specifications... 6 Table : Gearmotor Specifications... 6 U.S. Version - Standard Load... 6 CE Version - Standard Load... 6 U.S. Version - Heavy Load... 7 CE Version - Heavy Load... 7 Table : Belt Speed for Standard Load Fixed Speed Gearmotors... 7 U.S. Version (60 Hz Gearmotors)... 7 CE Version (50 Hz Gearmotors)... 7 Table : Belt Speed for Standard Load VFD Gearmotors 8 U.S. Version (60 Hz Gearmotors)... 8 CE Version (50 Hz Gearmotors)... 8 Table 4: Belt Speed for Heavy Load Fixed Speed Gearmotors... 9 U.S. Version (60 Hz Gearmotors)... 9 CE Version (50 Hz Gearmotors)... 9 Table 5: Belt Speed for Heavy Load VFD Gearmotors... 9 U.S. Version (60 Hz Gearmotors)... 9 CE Version (50 Hz Gearmotors)... 9 Installation... 0 Required Tools... 0 Recommended Installation Sequence... 0 Conveyors Up to ft (658mm)... 0 Conveyors Longer Than ft (658mm)... 0 Install Conveyor Tie Kits... 0 Install Belt and Bedstrip... Attach Conveyor to Stands... Mount Motor... Preventive Maintenance and Adjustment... Required Tools... Checklist... Lubrication... Maintaining Conveyor Belt... Troubleshooting... Cleaning... Conveyor Belt Replacement... Single Belt Replacement Option... Dual Belt Replacement Option... 5 Motor Replacement... 6 Gear Reducer Replacement... 6 Mid Drive Assembly... 7 Mid Drive Cartridge Replacement... 7 Tensioner Cam Replacement... 9 Service Parts... 0 Dual Strand Conveyor... 0 Support Stand... Corner Support Stand... 4 Connector Kit... 6 Conveyor Tie Bracket Industrial Gearmotors... 8 U.S. Version Gearmotors... 8 CE Version Gearmotors... 8 Conveyor Belt Part Number Configuration... 9 Return Policy Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

3 Introduction IMPORTANT Some illustrations may show guards removed. DO NOT operate equipment without guards. Upon receipt of shipment: Compare shipment with packing slip. Contact factory regarding discrepancies. Inspect packages for shipping damage. Contact carrier regarding damage. Accessories may be shipped loose. See accessory instructions for installation. Dorner s Limited Warranty applies. Dorner has convenient, pre configured kits of Key Service Parts for all conveyor products. These time saving kits are easy to order, designed for fast installation, and guarantee you will have what you need when you need it. Key Parts and Kits are marked in the Service Parts section of this manual with the Performance Parts Kits logo. Dorner reserves the right to make changes at any time without notice or obligation. 00 Precision Move Dual Strand Conveyor Rev. A Dorner Mfg. Corp.

4 Warnings General Safety A WARNING The safety alert symbol, black triangle with white exclamation, is used to alert you to potential personal injury hazards. A DANGER Climbing, sitting, walking or riding on conveyor will cause severe injury. KEEP OFF CONVEYORS. A DANGER A WARNING Dorner cannot control the physical installation and application of conveyors. Taking protective measures is the responsibility of the user. When conveyors are used in conjunction with other equipment or as part of a multiple conveyor system, CHECK FOR POTENTIAL PINCH POINTS and other mechanical hazards before system start-up. A WARNING DO NOT OPERATE CONVEYORS IN AN EXPLOSIVE ENVIRONMENT. A WARNING Loosening stand height or angle adjustment screws may cause conveyor sections to drop down, causing severe injury. SUPPORT CONVEYOR SECTIONS PRIOR TO LOOSENING STAND HEIGHT OR ANGLE ADJUSTMENT SCREWS. Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. A WARNING Gearmotors may be HOT. DO NOT TOUCH Gearmotors. 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

5 Product Description Refer to (Figure ) for typical components. Figure Conveyor Gearmotor Support Stand 4 Variable Speed Controller 4 Figure Specifications Models: Dual Strand Conveyor D S C M WWW LLLL M M G LLLL BB Belt Type Mid Drive Location Gearmotor Type Motor Orientation Motor Side Conveyor Length Conveyor Width Documentation Language Support Stands Conveyor Supports: Maximum Distances: = 8" (457 mm) = " (05 mm) = ft (658 mm)*** 4 = 8" (457 mm) *** For conveyors longer than ft (658 mm), install support at joint. Figure 4 DS P M WWW LH UH F Footing Type Tallest Height Lowest Height Stand Width Documentation Language Post Type Figure 00 Precision Move Dual Strand Conveyor Rev. A 5 Dorner Mfg. Corp.

6 Specifications Specifications Conveyor Width Reference (WWW) Conveyor Width 6.0" (60 mm) 9.45" (40 mm).60" (0 mm) 5.74" (400 mm) 8.90" (480 mm) Maximum Load 500 lb. (7 kg) Conveyor Startup Torque 7 in-lb (0.79 Nm) Belt Travel 7.88" (00 mm) per revolution of pulley Maximum Belt Speed 4 ft./minute (5 M/min) Conveyor Length Reference Conveyor Length 75 mm mm (0.8" ") Table : Gearmotor Specifications U.S. Version - Standard Load Item Standard Load Gearmotors Single Phase Three Phase VFD Variable Speed Output Power 0.5 Hp (0.9 kw) 0.8 Hp (0.8 kw) 0.8 Hp (0.8 kw) Input Voltage 5 VAC 08-0/460 VAC 08-0/460 VAC Input Frequency 60 Hz 60 Hz 0-60 Hz Input Current (Amperes)..9/0.95.9/0.95 Gearmotor Ratio 0:, 0:, 40:, 60: Frame Size NEMA 4 CZ C Face Motor Type Totally enclosed, fan cooled CE Version - Standard Load Item Standard Load Gearmotors Single Phase Three Phase VFD Variable Speed Output Power 0.8 kw 0.5 kw 0.5 kw Input Voltage 0 Volts AC 0/460 Volts AC 0 Volts AC Input Frequency 50 Hz 50 Hz 5-6 Hz Input Current (Amperes).6.4/0.8.4 Gearmotor Ratio 0:, 0:, 40:, 60: Frame Size IEC 6 B5 C Face Protection Rating IP 55 Totally enclosed, fan cooled 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

7 Specifications U.S. Version - Heavy Load Item Heavy Load Gearmotors Single Phase Three Phase VFD Variable Speed Output Power 0.50 Hp (0.7 kw) 0.8 Hp (0.8 kw) 0.8 Hp (0.8 kw) Input Voltage 5 VAC 08-0/460 VAC 08-0/460 VAC Input Frequency 60 Hz 60 Hz 0-60 Hz Input Current (Amperes) 5.7.-/.0.6/. Gearmotor Ratio 0:, 0:, 40:, 60: Frame Size NEMA 56 C Face Motor Type Totally enclosed, fan cooled CE Version - Heavy Load Item Heavy Load Gearmotors Single Phase Three Phase VFD Variable Speed Output Power 0.7 kw Input Voltage 0 Volts AC 0/460 Volts AC 0 Volts AC Input Frequency 50 Hz 50 Hz 5-6 Hz Input Current (Amperes).6./../. Gearmotor Ratio 0:, 0:, 40:, 60: Frame Size IEC 7 B5 C Face Protection Rating IP 55 Totally enclosed, fan cooled Table : Belt Speed for Standard Load Fixed Speed Gearmotors U.S. Version (60 Hz Gearmotors) Part Number RPM In-Lb N-m Belt Speed Ft/min M/min 6M060ES4(vp)FN M040ES4(vp)FN M00ES4(vp)FN M00ES4(vp)FN (vp) = voltage and phase = 5 V, phase = 08-0/460 V, phase CE Version (50 Hz Gearmotors) Part Number RPM N-m Belt Speed Ft/min M/min 6Z060ES4(vp)FN Z040ES4(vp)FN Z00ES4(vp)FN Z00ES4(vp)FN (vp) = voltage and phase = 0 V, phase = 0 V, phase 4 = 400 V, phase 00 Precision Move Dual Strand Conveyor Rev. A 7 Dorner Mfg. Corp.

8 Specifications Table : Belt Speed for Standard Load VFD Gearmotors U.S. Version (60 Hz Gearmotors) Part Number RPM In-Lb N-m Belt Speed Ft/min M/min 6M060ES4(vp)EN M040ES4(vp)EN M00ES4(vp)EN M00ES4(vp)EN (vp) = voltage and phase = 5 V, phase = 08-0/460 V, phase CE Version (50 Hz Gearmotors) Part Number RPM N-m Belt Speed Ft/min M/min 6Z060ES4(vp)EN Z040ES4(vp)EN Z00ES4(vp)EN Z00ES4(vp)EN (vp) = voltage and phase = 0 V, phase = 0 V, phase 4 = 400 V, phase 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

9 Table 4: Belt Speed for Heavy Load Fixed Speed Gearmotors U.S. Version (60 Hz Gearmotors) Part Number RPM In-Lb N-m Belt Speed Ft/min M/min M060ES4(vp)FN M040ES4(vp)FN M00ES4(vp)FN M00ES4(vp)FN (vp) = voltage and phase = 5 V, phase = 08-0/460 V, phase CE Version (50 Hz Gearmotors) Part Number RPM N-m Belt Speed Ft/min M/min 6Z060ES4(vp)FN Z040ES4(vp)FN Z00ES4(vp)FN Z00ES4(vp)FN (vp) = voltage and phase = 0 V, phase = 0 V, phase 4 = 400 V, phase Table 5: Belt Speed for Heavy Load VFD Gearmotors U.S. Version (60 Hz Gearmotors) CE Version (50 Hz Gearmotors) Specifications Part Number RPM In-Lb N-m Belt Speed Ft/min M/min M060ES4EN M040ES4EN M00ES4EN M00ES4EN Part Number RPM N-m Belt Speed Ft/min M/min 6Z060ES4EN Z040ES4EN Z00ES4EN Z00ES4EN Precision Move Dual Strand Conveyor Rev. A 9 Dorner Mfg. Corp.

10 Installation Required Tools 4 mm Hex Wrench 6 mm Hex Wrench 8 mm Hex Wrench 7/6" Wrench 9/6" Wrench NOTE Conveyor MUST be mounted straight, flat and level within confines of conveyor. Use a level for setup. Conveyors Longer Than ft (658mm) Install Conveyor Tie Kits Figure NOTE Be sure all frame sections (Figure, item ) are properly supported during assembly. Recommended Installation Sequence Assemble conveyor (if applicable) Install conveyor tie kits (if applicable) Attach conveyor to stands Mount motor Conveyors Up to ft (658mm) No conveyor assembly required. Figure NOTE Tie bars can be used in either outer or inner slots.. Join both conveyor sections, and tighten set screws (Figure 4, item ) on both sides. Tighten all set screws /4 turn past contact with frame. Figure 4 Figure 4 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

11 Installation Install Belt and Bedstrip. Loop belt (Figure 5, item ) around roller assembly (Figure 5, item ). Insert roller assembly into end cap (Figure 5, item ). Insert roller pin (Figure 5, item 4) into roller assembly. Figure 5 4. Install the bedstrip (Figure 7, item ) between the conveyor (Figure 7, item ) and belt (Figure 7, item ). Make sure that the high side (Figure 7, item 4) faces out and snap bedstrip into place. Figure 7 4 Figure 5. Snap the end cap (Figure 6, item ) into the conveyor (Figure 6, item ) on both ends. Make sure that the high side (Figure 6, item ) faces out. Ensure end cap is seated tight against frame on both sides. Figure 6 Figure 7 4. Rotate the tensioner cams (Figure 8, item ) in the direction indicated to tension belt. Figure 8 Figure 8 Figure 6 00 Precision Move Dual Strand Conveyor Rev. A Dorner Mfg. Corp.

12 Installation Attach Conveyor to Stands NOTE For detailed assembly instruction, please see your appropriate support stand manual.. Assemble washer (Figure 9, item ) onto socket head screw (Figure 9, item ). Thread bolt into slide-in nut (Figure 9, item ). Repeat for a second bolt, washer, and nut. Mount Motor. Attach the motor (Figure, item ) to the gear reducer (Figure, item ) with hex flange screws (Figure, item ). Tighten screws. Figure Figure 9 4 Figure Figure 9. Insert bolt and nut assemblies through end cap (Figure 9, item 4) and into conveyor channel. Slide one down the channel, keeping the second close to the end of the conveyor.. Raise stand leg (Figure 0, item ) to bottom of conveyor. Make sure top plate mounting screws (Figure 0, item ) align into channel. Figure 0 4 Figure 0 4. Slide mounting hardware (Figure 0, item ) into slot (Figure 0, item 4) on both sides of top plate and tighten. 5. Repeat for other leg of stand. 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

13 Preventive Maintenance and Adjustment Required Tools 4 mm Hex Wrench 6 mm Hex Wrench 8 mm Hex Wrench 7/6" Wrench 9/6" Wrench Checklist Keep service parts on hand (see Service Parts section for recommendations) Keep supply of belt cleaner Clean entire conveyor and mid drive while disassembled Replace worn or damaged parts Lubrication No lubrication is required. Replace roller assemblies if worn. Maintaining Conveyor Belt Troubleshooting Inspect conveyor belt for: Surface cuts or wear Stalling or slipping Surface cuts and wear indicate: Sharp or heavy parts impacting belt Jammed parts Foreign material inside the conveyor Improperly positioned accessories Bolt-on guiding is pinching belt Stalling or slipping indicates: Excessive load on belt Conveyor belt not properly tensioned Intermittent jamming or drive train problems Conveyor Belt Replacement For Single Conveyor Belt, See Single Belt Replacement Option on page For Dual Conveyor Belt, See Dual Belt Replacement Option on page 5 Single Belt Replacement Option. Rotate tensioner cams (Figure, item ) in the direction indicated to release tension on belt. Figure Figure. Remove the bedstrip (Figure, item ) from between the conveyor (Figure, item ) and belt (Figure, item ). Figure A WARNING Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Cleaning Use Dorner Belt Cleaner. Mild soap and water may also be used. Do not soak the belt. Figure 00 Precision Move Dual Strand Conveyor Rev. A Dorner Mfg. Corp.

14 Preventive Maintenance and Adjustment. Remove the end cap (Figure 4, item ) from the conveyor (Figure 4, item ) on both ends. Figure 4 8. While pressing in on hex flange screws, remove mid drive cartridge (Figure 7, item ) from mid drive assembly (Figure 7, item ). Figure 7 Figure 4 4. Remove button head screws (Figure 5, item ). Figure 5 Figure 7 9. Remove belt assembly from mid drive and conveyor channel. 0. Remove roller pin (Figure 8, item ) and roller assembly with belt (Figure 8, item ) from end cap (Figure 8, item ) on both ends of belt. Figure 8 Figure 5 5. Loosen hex flange screws (Figure 5, item ) on both sides of conveyor. Remove mid drive cover (Figure 5, item ). 6. Remove retaining ring on opposite conveyor. 7. Using a punch and hammer, carefully tap the shaft (Figure 6, item ) out of the mid drive assembly. Figure 6 Figure 8. Inspect roller assemblies and end caps for wear or damage. Replace as needed.. Install new belt in the reverse order of removal.. Rotate the tensioner cams (Figure 9, item ) in the direction indicated to tension belt. Figure 9 Figure 6 00 Precision Move Dual Strand Conveyor Figure 9 Dorner Mfg. Corp Rev. A

15 Preventive Maintenance and Adjustment Dual Belt Replacement Option. Remove hex flange screws (Figure 0, item ) connecting the motor (Figure 0, item ) to the gear reducer (Figure 0, item ). 4. Remove the end cap (Figure, item ) from the conveyor (Figure, item ) on both ends. Figure Figure 0 Figure 0. Rotate tensioner cams (Figure, item ) in the direction indicated to release tension on belt. Figure Figure 5. Loosen inner and outer screws (Figure 4, item ). While pressing in on hex flange screws, lift mid drive assembly (Figure 4, item ) from conveyors. Figure 4 Figure. Remove the bedstrip (Figure, item ) from between the conveyor (Figure, item ) and belt (Figure, item ). Figure Figure 4 6. Remove belt assembly from mid drive and conveyor channel. 7. Remove roller pin (Figure 5, item ) and roller assembly with belt (Figure 5, item ) from end cap (Figure 5, item ) on both ends of belt. Figure 5 Figure 5 Figure 00 Precision Move Dual Strand Conveyor Rev. A 5 Dorner Mfg. Corp.

16 Preventive Maintenance and Adjustment 8. Inspect roller assemblies and end caps for wear or damage. Replace as needed. 9. Install new belt in the reverse order of removal. 0. Rotate the tensioner cams (Figure 6, item ) in the direction indicated to tension belt.. If the shaft of the motor is seized in the gear reducer, install hex flange screws (Figure 8, item ) into the threaded holes of the gear reducer. Turn screws evenly clockwise to free motor from gear reducer. Figure 8 Figure 6 Figure 6 Motor Replacement A WARNING Figure 8 Gear Reducer Replacement A WARNING. Remove hex flange screws (Figure 7, item ) connecting the motor (Figure 7, item ) to the gear reducer (Figure 7, item ). Figure 7 Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance.. Remove motor. See "Motor Replacement" on page 6. Remove button head screws (Figure 9, item ). Figure 9 Figure 7 Figure 9. Remove hex flange screws (Figure 9, item ) and mid drive cover (Figure 9, item ). 4. Remove retaining ring. 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

17 Preventive Maintenance and Adjustment 5. From opposite side, using a punch and hammer, carefully tap the shaft (Figure 0, item ) out of the mid drive assembly. Figure 0 Mid Drive Assembly A WARNING Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Mid Drive Cartridge Replacement. Remove motor. See "Motor Replacement" on page 6. Remove button head screws (Figure, item ). Figure Figure 0 6. Remove flat screws (Figure, item ), mounting plate (Figure, item ), and stand-off extrusion (Figure, item ) from gear reducer. Figure Figure 7. Install new gear reducer and assemble in reverse order of removal. Figure. Remove hex flange screws (Figure, item ) and mid drive cover (Figure, item ). Replace hex flange screws (Figure, item ), but do not tighten. 4. Repeat steps and for cover on opposite conveyor. 5. Rotate tensioner cams (Figure, item ) in the direction indicated to release tension on belt. Figure Figure 00 Precision Move Dual Strand Conveyor Rev. A 7 Dorner Mfg. Corp.

18 Preventive Maintenance and Adjustment 6. Remove the bedstrip (Figure 4, item ) from between the conveyor (Figure 4, item ) and belt (Figure 4, item ). Figure 4 0. Remove mid drive cartridge: a. Non-Drive Side: Loosen hex flange screws (Figure 7, item ). While pressing in on hex flange screws lift mid drive cartridge (Figure 7, item ) from mid drive assembly (Figure 7, item ). Figure 7 Figure 4 7. Remove the end cap (Figure 5, item ) from the conveyor (Figure 5, item ) on both ends. Figure 5 Figure 7 b. Drive Side: Remove hex flange screws (Figure 8, item ). Press in on hex flange screws (Figure 8, item ) and lift mid drive cartridge (Figure 8, item ) from mid drive assembly (Figure 8, item 4). Figure 8 Figure 5 8. Remove retaining ring. 9. Using a punch and hammer, carefully tap the shaft (Figure 6, item ) out of the mid drive assembly. Figure 6 4 Figure 8. Inspect mid drive cartidge for wear or damage and replace as needed.. Installation is the reverse order of removal. Figure 6 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

19 Preventive Maintenance and Adjustment Tensioner Cam Replacement. Remove motor. See "Motor Replacement" on page 6. Remove mid drive cartridge. See "Mid Drive Cartridge Replacement" on page 7. Remove belt assembly from mid drive and conveyor channel. 4. Remove torx screws (Figure 9, item ) and mid drive side plate (Figure 9, item ). 7. Remove roller pin (Figure 4, item ), roller assembly (Figure 4, item ), tensioner axle (Figure 4, item ) and tensioner spring (Figure 4, item 4) from tensioner block. Figure 4 Figure 9 Figure 4 8. Inspect and replace worn or damaged parts. 4 Figure 9 5. Remove tensioner block assemblies (Figure 40, item ). Figure 40 NOTE When installing tensioner block assemblies (Figure 40, item ) into side plate, make sure that the tensioner cam lobes (Figure 40, item ) are facing up. 9. Assemble components in the reverse order of removal. Ensure that the springs are installed correctly; note the direction of the long leg as shown in (Figure 40, item 4) 4 Figure Remove tensioner cams (Figure 40, item ). Inspect for wear and replace as needed. 00 Precision Move Dual Strand Conveyor Rev. A 9 Dorner Mfg. Corp.

20 Service Parts Dual Strand Conveyor NOTE For replacement parts other than those shown in this section, contact an authorized Dorner Service Center or the factory. Key Service Parts and Kits are identified by the Performance Parts Kits logo. Dorner recommends keeping these parts on hand Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

21 Service Parts Item Part Number Description Bedstrip, High Side 0556-WWW Crossmember 0457 Key Bar M Socket Head Screw, M6-.00 x 0mm M Drop-In Tee Bar LLLLL Frame Rail Mid Drive Cover Tensioner Axle Torx Screw, M5 x Mid Drive End Cover 85- Tensioner Block 85-0 Tensioner Spring Mid Drive Cartridge Torx Screw, M6-.00 x 0mm Hex Flange Screw, M x 0mm Tensioner Cam Mid Drive Side Plate Right End Cap with High Side Roller Pin Roller Assembly 85-4 Left End Cap with High Side 0454-WWW Shaft 0454 Mounting Plate Stand-Off Extrusion LLLLL Shaft Guard M Flat Screw, M6-.00 x 40 mm for 4CZ C Faced Motors Only 9060M Flat Screw, M6-.00 x 0 mm for 56 C Faced Motors Only Dowel Pin WWW Square Key for 4CZ C Faced Motors Only Square Key for 56 C Faced Motors Only 044 Square Key for IEC 6 or 7 B5 C Faced Motors Only LLLLL Square Key for 56 C Faced Motors Only 505 Adapter Ring for 56 C Faced Motors Only 80-6 Flanged Bearing for 56 C Faced Motors Only 80-6 Flanged Bearing for IEC 6 or 7 B5 C Faced Motors Only Retaining Ring WWW = Conveyor width reference: 60, 40, 0, 400, 480 LLLLL = Part length in inches with two decimal places. Length Example: Length = 95.5" LLLLL = Precision Move Dual Strand Conveyor Rev. A Dorner Mfg. Corp.

22 Service Parts Support Stand Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

23 Service Parts Item Part Number Description 700-LLLLL Crossmember 700-LLLLL Boot 70-LLLLL Leg Foot End Plate 6 906M Button Head Screw, M0-.50 x 6 mm Top Plate P Trilobe Screw, M6-.00 x 5 mm Slide-In Nut, M M Socket Head Screw, M8-.5 x 6 mm M hex flange Cap Screw, M8-.5 x 0 mm 990M Hex Nut, M P Washer LLLLL = Part length in inches with two decimal places. Length Example: Length = 95.5" LLLLL = Precision Move Dual Strand Conveyor Rev. A Dorner Mfg. Corp.

24 Service Parts Corner Support Stand Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

25 Service Parts Item Part Number Description 700-LLLLL Crossmember 700-LLLLL Boot 70-LLLLL Leg Foot End Plate 6 906M Button Head Screw, M0-.50 x 6 mm Top Plate P Trilobe Screw, M6-.00 x 5 mm Slide-In Nut, M M Socket Head Screw, M8-.5 x 6 mm M hex flange Cap Screw, M8-.5 x 0 mm 990M Hex Nut, M P Washer LLLLL = Part length in inches with two decimal places. Length Example: Length = 95.5" LLLLL = Precision Move Dual Strand Conveyor Rev. A 5 Dorner Mfg. Corp.

26 Service Parts Connector Kit Item Part Number Description Connector M Set Screw, M8-.5 x 8 mm 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

27 Service Parts Conveyor Tie Bracket Item Part Number Description Plate Twist-In Stud, M8 x 5 mm 9908M Lock Nut 00 Precision Move Dual Strand Conveyor Rev. A 7 Dorner Mfg. Corp.

28 Service Parts 90 Industrial Gearmotors CE Version Gearmotors U.S. Version Gearmotors Item Part No. Part Description 6MES4FN Motor, 0.5 Hp (0.9 Kw) 5/0 Volts, 60 Hz, -Phase 6MES4FN Motor, 0.5 Hp (0.9 Kw) 08-0/460 Volts, 60 Hz, -Phase MS4EI Motor, 0.5 Hp (0.9 Kw) 0/460 Volts DC, 60 Hz, -Phase Variable Frequency 6MEH4FN Motor, 0.5 hp (0.7 Kw) 5/0 Volts, 60 Hz, -Phase, non reversing MES4EN Motor, 0.5 hp (0.7 Kw) 0V, 0 60Hz, Phase MEH4FN Motor, 0.5 hp (0.7 Kw) 08 0/460 Volts, 60 Hz, -Phase M00EL Gear Reducer, 0:, 4CZ M00EL Gear Reducer, 0:, 4CZ M040EL Gear Reducer, 40:, 4CZ M060EL Gear Reducer, 60:, 4CZ M00ES Gear Reducer, 0:, 56C M00ES Gear Reducer, 0:, 56C M040ES Gear Reducer, 40:, 56C M060ES Gear Reducer, 60:, 56C Item Part Number Description 86-8 Motor, 0.9 Kw 0 Volts, 400 RPM 50 Hz, -Phase Motor, 0.9 Kw 0/400 Volts, 400 RPM 50 Hz, -Phase 86-4 Motor, 0.9 Kw 0/400 Volts, 50 Hz, - Phase 6Z00ES Gear Reducer, 0:, 6 B5 6Z00ES Gear Reducer, 0:, 6 B5 6Z040ES Gear Reducer, 40:, 6 B5 6Z060ES Gear Reducer, 60:, 6 B5 00 Precision Move Dual Strand Conveyor Dorner Mfg. Corp Rev. A

29 Conveyor Belt Part Number Configuration Figure 4 Service Parts DSCMWWW-LLLLMOG-PPPPBB SERIAL # MODEL # DORNER MFG. CORP. HARTLAND, WI USA Refer to Dorner serial number plate (Figure 4). From the model number, determine conveyor length ( LLLL ) and belt type ( BB ). Use data to configure belt part number as indicated below. Figure 4 DSB - LLLLBB DSB (Fill In) 00 Precision Move Dual Strand Conveyor Rev. A 9 Dorner Mfg. Corp.

30 Return Policy Returns must have prior written factory authorization or they will not be accepted. Items that are returned to Dorner without authorization will not be credited nor returned to the original sender. When calling for authorization, please have the following information ready for the Dorner factory representative or your local distributor:. Name and address of customer.. Dorner part number(s) of item(s) being returned.. Reason for return. 4. Customer's original order number used when ordering the item(s). 5. Dorner or distributor invoice number (if available, part serial number). A representative will discuss action to be taken on the returned items and provide a Returned Goods Authorization (RMA) number for reference. RMA will automatically close 0 days after being issued. To get credit, items must be new and undamaged. There will be a return charge on all items returned for credit, where Dorner was not at fault. It is the customer s responsibility to prevent damage during return shipping. Damaged or modified items will not be accepted. The customer is responsible for return freight. Product Line 00 Conveyors Gearmotors & Mounting Packages Support Stands Product Type Standard Products Accessories Spare Parts (non-belt) Spare Belts - Standard Flat Fabric Spare Belts - Cleated & Specialty Fabric Spare Belts - Plastic Chain Engineered to order parts All equipment and parts Modular Belt 00 Precision Move Modular Belt 00 0% return fee for all products except: 50% return fee for conveyors with modular belt, 00 LPZ cleated belt or specialty belts non-returnable case-by-case 00 Precision Move Controls 700 / % return fee for all products non-returnable Returns will not be accepted after 60 days from original invoice date. The return charge covers inspection, cleaning, disassembly, disposal and reissuing of components to inventory. If a replacement is needed prior to evaluation of returned item, a purchase order must be issued. Credit (if any) is issued only after return and evaluation is complete. Dorner has representatives throughout the world. Contact Dorner for the name of your local representative. Our Customer Service Team will gladly help with your questions on Dorner products. For a copy of Dorner's Warranty, contact factory, distributor, service center or visit our website at For replacement parts, contact an authorized Dorner Service Center or the factory. Dorner Mfg. Corp. reserves the right to change or discontinue products without notice. All products and services are covered in accordance with our standard warranty. All rights reserved. Dorner Mfg. Corp. 05 DORNER MFG. CORP. 975 Cottonwood Ave., PO Box 0 Hartland, WI USA TEL (USA) FAX (USA) Internet: Outside the USA: TEL FAX Rev. A Printed in U.S.A.