2200 and 2300 Series Modular Belt Conveyors

Transcription

1 00 and 00 Series Modular Belt Conveyors Installation, Maintenance & Parts Manual End Drive Conveyor Center Drive Conveyor DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box Cottonwood Ave. TEL: TEL: Hartland, WI USA FAX: FAX: Rev. C For other service manuals visit our website at:

2 Table of Contents Introduction... Warnings General Safety... Product Description... Specifications... 5 Models:... 5 Conveyor Supports:... 5 Specifications:... 5 Table : Center Drive 90 Gearmotor Specifications... 6 Table : Center Drive Parallel Shaft Gearmotor Specifications... 6 Table : Belt Speeds for Standard & Heavy Load Fixed Speed 90 Gearmotors... 6 Table : Belt Speeds for Standard & Heavy Load Variable Speed 90 DC Gearmotors... 7 Table 5: Belt Speeds for Heavy Load Variable Speed 90 VFD Gearmotors... 7 Table 6: Belt Speeds for Standard Load Fixed Speed Parallel Shaft 60 Hz Gearmotors on MPD Series Conveyors... 7 Table 7: Belt Speeds for Standard Load Variable Speed Parallel Shaft VFD Gearmotors on MPD Series Conveyors... 8 Table 8: Belt Speeds for Standard Load Variable Speed Parallel Shaft DC Gearmotors on MPB Series Conveyors... 8 No Load Torque... 9 No Load Torque Data... 9 Load vs. Speed vs Conveyor Length Per Width... 0 Wide Conveyor Wide Conveyor... 0 Wide Conveyor... Wide Conveyor... Installation... Required Tools... Recommended Installation Sequence... Conveyors Up to 0 ft (08 mm)... Conveyors Longer Than 0 ft (08 mm) Series Mounting Brackets Series Mounting Brackets... Installing Plastic Belt... 5 Proper Methods of Attachment to Side Rails (00 Series Only)... 6 Self-Drilling Screws... 6 Pre-Drill for Standard Screws... 6 Guiding (00 Series Only)... 7 Preventive Maintenance and Adjustment... 8 Required Tools... 8 Introduction IMPORTANT Some illustrations may show guards removed. DO NOT operate equipment without guards. Upon receipt of shipment: Compare shipment with packing slip. Contact factory regarding discrepancies. Inspect packages for shipping damage. Contact carrier regarding damage. Accessories may be shipped loose. See accessory instructions for installation. Standard Tools... 8 Special Tools... 8 Checklist... 8 Lubrication... 8 Maintaining Conveyor Belt... 8 Conveyor Belt Replacement... 8 Conveyor Belt Replacement Sequence... 8 Belt Removal... 8 Belt Installation... 9 Conveyor Belt Tension... 0 Removal of Belt Links... 0 Pulley and Sprockets Removal... A End Drive Conveyor... B Center Drive Conveyor... Bearing Removal & Replacement... Removal... Replacement... Pulley and Sprockets Replacement... Idler End Wear Items... 5 A - Standard Idler Tail... 5 B - Nose Bar Idler Tail... 6 Upper Wear Strip Replacement... 7 Lower Wear Strip Replacement... 7 Service Parts... 8 Drive End... 8 Idler End... 0 Nose Bar Idler End... Center Drive Module... Parallel Shaft Gearmotors Gearmotors Series Frame Assembly Series Frame Assembly... 6 Connecting Assembly without Stand Mounts... 7 Connecting Assembly with Mounting Brackets... 7 Return Wear Strip Low Side (76 mm) Aluminum Side (8 mm) Aluminum Side Low to High Side... Adjustable Guiding... Tool-Less Adjustable Guiding... Mounting Brackets... 5 Mounting Brackets for (60 mm) Conveyors... 5 Mounting Brackets for Short Center Drive Conveyors.. 6 Conveyor Belting... 6 Belting Per Foot (05 mm)... 6 Notes... 7 Return Policy... 8 Dorner s Limited Warranty applies. Dorner 00 & 00 series conveyors are covered by Patent Numbers 5,7,5, 6,98,98, 6,,8 and corresponding patents and patent applications in other countries. Dorner reserves the right to make changes at any time without notice or obligation. Dorner has convenient, pre configured kits of Key Service Parts for all conveyor products. These time saving kits are easy to order, designed for fast installation, and guarantee you will have what you need when you need it. Key Parts and Kits are marked in the Service Parts section of this manual with the Performance Parts Kits logo. Dorner Mfg. Corp Rev. C

3 Warnings General Safety A WARNING The safety alert symbol, black triangle with white exclamation, is used to alert you to potential personal injury hazards. A DANGER A WARNING Top and Bottom Mount Gearmotors must be mounted as shown below. Failure to do so creates pinch points which can cause severe injury. Climbing, sitting, walking or riding on conveyor will cause severe injury. KEEP OFF CONVEYORS. A DANGER Bottom Mount Top Mount DO NOT OPERATE CONVEYORS IN AN EXPLOSIVE ENVIRONMENT. A WARNING Gearmotors may be HOT. DO NOT TOUCH Gearmotors. A WARNING A WARNING Dorner cannot control the physical installation and application of conveyors. Taking protective measures is the responsibility of the user. When conveyors are used in conjunction with other equipment or as part of a multiple conveyor system, CHECK FOR POTENTIAL PINCH POINTS and other mechanical hazards before system start-up. A WARNING Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. A WARNING Loosening stand height or angle adjustment screws may cause conveyor sections to drop down, causing severe injury. SUPPORT CONVEYOR SECTIONS PRIOR TO LOOSENING STAND HEIGHT OR ANGLE ADJUSTMENT SCREWS. Conveyors are not reversible. Reversing creates pinch points which can cause severe injury. DO NOT REVERSE CONVEYORS Rev. C Dorner Mfg. Corp.

4 Product Description Refer to Figure for typical conveyor components. Figure Conveyor Guiding & Accessories Mounting Brackets Support Stand 5 Drive End 6 Idler/Tension End 7 Center Drive Box (Center Drive Units) 5 6 End Drive Conveyor Figure Figure Center Drive Conveyor Figure Dorner Mfg. Corp Rev. C

5 Specifications Models: E M WW LLLL A A A A Belt Type* "D" Side Profile "A" Side Profile Output Shaft Position Ider Tail Drive Tail: Mounting Brackets: Conveyor Supports: Maximum Distances: = 8 (57 mm)** = 6 ft (89 mm)*** = 8 (57 mm) ** For Heavy Load Bottom Mount Package, mount support under gear head. *** For conveyors longer than 0 ft (08 mm), install support at joint. Figure Conveyor Length* Conveyor Width* Conveyor Series: = 00 F = 00 Drive Type: E = End Drive T = Center Drive * See Ordering and Specifications Catalog for details. Center drive location to be at center of first frame section. Minimum center drive conveyor length is 6 (9 cm). Specifications: Figure Conveyor Width Reference (WW) 0 08 Conveyor Belt Width.0 (0 mm) 8.0 (0 mm).0 (05 mm).0 (60 mm) Conveyor Length Reference (LLLL) 000 to 000 in 000 increments Conveyor Length ft (60mm) to 0 ft (9mm) in 0. (6mm) increments Belt Travel.5 (90 mm) per revolution of pulley Maximum Belt Speed* 50 ft/minute (76. m/minute) Rev. C 5 Dorner Mfg. Corp.

6 Specifications Table : Center Drive 90 Gearmotor Specifications Standard Load Gearmotor Heavy Load Gearmotor Single- DC Variable Single- VFD Variable Three Phase Three Phase Phase Speed Phase Speed Output Power 0.5 hp (0.9 kw) 0.5 hp (0.7 kw) Input Voltage 5VAC 08 0/60 VAC 0VDC 5VAC 08 0/60 VAC Table : Center Drive Parallel Shaft Gearmotor Specifications Table : Belt Speeds for Standard & Heavy Load Fixed Speed 90 Gearmotors DC Variable Speed 0 VAC 90VDC Input Frequency 60Hz N/A 60Hz 0 60Hz N/A Input Current (Amperes) 5.0./ / Gearmotor Ratios 5:, 0:, 0:, 0:, 60: 5:, 0:, 0:, 0:, 60: Frame Size NEMA CZ NEMA 56C Motor Type Totally enclosed, Fan cooled Totally enclosed, Fan cooled Single Phase Three Phase DC Variable Speed Output Power 0.7 hp (0. kw) 0.5 hp (0.9 kw) Input Voltage 5 Volts A.C. 0 Volts A.C. 0 Volts D.C. Input Frequency 60 Hz N/A Input Current.9 Amperes. Amperes.8 Amperes Motor RPM Gearmotor Ratios 5:, 0:, 0:, 0:, 60:, 80: Motor Type Totally enclosed, Fan-cooled Totally enclosed, Non ventilated Standard Load Gearmotors Heavy Load Gearmotors Belt Speed Drive Driven Part Number RPM In-lb N-m Part Number RPM In-lb N-m Ft/min M/min Pulley Pulley M060EL(vp)F(n) M060HS(vp)F(n) M060EL(vp)F(n) M060HS(vp)F(n) M00EL(vp)F(n) M00HS(vp)F(n) M00EL(vp)F(n) M00HS(vp)F(n) M00EL(vp)F(n) 86 6 M00HS(vp)F(n) M00EL(vp)F(n) 86 6 M00HS(vp)F(n) M00EL(vp)F(n) M00HS(vp)F(n) M00EL(vp)F(n) M00HS(vp)F(n) M005EL(vp)F(n) 5.6 M005HS(vp)F(n) M005EL(vp)F(n) 5.6 M005HS(vp)F(n) M005EL(vp)F(n) 5.6 M005HS(vp)F(n) M005EL(vp)F(n) 5.6 M005HS(vp)F(n) M005EL(vp)F(n) 5.6 M005HS(vp)F(n) (vp) = voltage and phase = 5 V, -phase = 08 0/60 V, -phase Dorner Mfg. Corp Rev. C

7 Specifications Table : Belt Speeds for Standard & Heavy Load Variable Speed 90 DC Gearmotors Standard Load Gearmotors Heavy Load Gearmotors Belt Speed Drive Driven Part Number RPM In-lb N-m Part Number RPM In-lb N-m Ft/min M/min Pulley Pulley M060ELDDEN 98. M060HSD9DEN M060ELDDEN 98. M060HSD9DEN M00ELDDEN M00HSD9DEN M00ELDDEN M00HSD9DEN M00ELDDEN M00HSD9DEN M00ELDDEN M00HSD9DEN M005ELDDEN M005HSD9DEN M005ELDDEN M005HSD9DEN M005ELDDEN M005HSD9DEN Table 5: Belt Speeds for Heavy Load Variable Speed 90 VFD Gearmotors Heavy Load Gearmotors Belt Speed Drive Driven Part Number RPM In-lb N-m Ft/min M/min Pulley Pulley M060ESEN M060ESEN M00ESEN M00ESEN M00ESEN M00ESEN M005ESEN M005ESEN M005ESEN Table 6: Belt Speeds for Standard Load Fixed Speed Parallel Shaft 60 Hz Gearmotors on MPD Series Conveyors Gearmotors Belt Speed Drive Driven Part Number Gear Ratio RPM In-lb N-m Ft/min M/min Pulley Pulley 6M80PS(vp)F(n) 80: M060PS(vp)F(n) 60: M80PS(vp)F(n) 80: M060PS(vp)F(n) 60: M060PS(vp)F(n) 60: M00PS(vp)F(n) 0: M00PS(vp)F(n) 0: (vp) = voltage and phase = 5V, -phase = 0V, -phase (n) = reversing capability N = no reversing switch R = with reversing switch (5V, phase only) Rev. C 7 Dorner Mfg. Corp.

8 Specifications Table 7: Belt Speeds for Standard Load Variable Speed Parallel Shaft VFD Gearmotors on MPD Series Conveyors Gearmotors Belt Speed Drive Driven Part Number Gear Ratio RPM* In-lb* N-m* Ft/min M/min Pulley Pulley 6M060PSEN 60: M060PSEN 60: M00PSEN 0: M00PSEN 0: M00PSEN 0: M005PSEN 5: * At 60 Hz Table 8: Belt Speeds for Standard Load Variable Speed Parallel Shaft DC Gearmotors on MPB Series Conveyors Gearmotors Belt Speed Drive Driven Part Number Gear Ratio RPM In-lb N-m Ft/min M/min Pulley Pulley 6M80PSDDEN 80: M060PSDDEN 60: M060PSDDEN 60: M060PSDDEN 60: M00PSDDEN 0: M00PSDDEN 0: M00PSDDEN 0: M00PSDDEN 0: M00PSDDEN 0: * = Cleated and Sidewall Cleated belts operate at a maximum of 50 Ft/min (5.7 m/min) NOTE For belt speed other than those listed, contact factory for details. Dorner Mfg. Corp Rev. C

9 No Load Torque Specifications No Load Torque Data NOTE. The torque required to overcome the conveyor s initial startup inertia may temporarily exceed the average no load torque by a factor of to times.. Stated torques are average values based on Dorner standard belts running at 50 (5meters) per minute. Width Length(feet).0 (0 mm) 8.0 (0 mm).0 (05 mm).0 (60 mm) in lbs N m in lbs N m in lbs N m in lbs N m Rev. C 9 Dorner Mfg. Corp.

10 Specifications Load vs. Speed vs Conveyor Length Per Width Wide Conveyor NOTE Maximum conveyor loads based on: Non-accumulating product Product moving towards gearmotor Conveyor being mounted horizontal Load (lbs) " Wide Conveyor 0' 0' 0' 5' ' Belt Speed (Ft/Min) ' 5' 0' 0' 0' 8 Wide Conveyor 0 8" Wide Conveyor Load (lbs) ' 5' ' 0' 0' ' 5' 0' 0' 0' Belt Speed (Ft/Min) Dorner Mfg. Corp Rev. C

11 Specifications Wide Conveyor " Wide Conveyor ' 0' Load (lbs) ' 0' ' 5' 0' 0 ' 0' 0 0' Belt Speed (Ft/Min) Wide Conveyor " Wide Conveyor 0' 5' 0' Load (lbs) ' 0' ' 5' 0' 0 0' 0 0' Belt Speed (Ft/Min) Rev. C Dorner Mfg. Corp.

12 Installation A WARNING Conveyors are not reversible. Reversing creates pinch points which can cause severe injury. DO NOT REVERSE CONVEYORS. A WARNING Top and Bottom Mount Gearmotors must be mounted as shown below. Failure to do so creates pinch points which can cause severe injury. Bottom Mount Required Tools Hex-key wrenches: mm, 5 mm Level Torque wrench / (. mm) wide Flat Blade screwdriver Recommended Installation Sequence Install support stands (see accessory instructions) Assemble conveyor frame (if required) (page ) Attach mounting brackets to conveyor frame and stands (page ) Install Belt (page 5) Mount gearmotor mounting package (see accessory instructions) Attach guides/accessories (Refer to Service Parts on page 8 for details) Conveyors Up to 0 ft (08 mm) No assembly is required. Install mounting brackets. Refer to Mounting Brackets on page. Top Mount NOTE Conveyor MUST be mounted straight, flat and level within confines of conveyor. Use a level (Figure, item ) for setup. Figure Figure Dorner Mfg. Corp Rev. C

13 Conveyors Longer Than 0 ft (08 mm). Locate conveyor sections (Figure 5, item ). Installation 00 Series Mounting Brackets. Locate brackets. Exploded view shown in Figure 7. Figure 7 Figure 5 5 Figure 5. Join conveyor sections and install connector brackets (Figure 6, item ) or connector/mount brackets (Figure 6, item ) and screws (Figure 6, item ) on both sides as indicated. Figure 6 Figure 6. Tighten screw (Figure 6, item ) to 60 in-lb (7 Nm) on both sides of conveyor. Figure 7. Remove screws (Figure 7, item & ), washers (Figure 7, item ), connector bars (Figure 7, item ) and T-bars (Figure 7, item 5) from brackets.. Insert T-bars (Figure 7, item 5) into conveyor side slots (Figure 8, item ). Fasten brackets (Figure 8, item ) to conveyor with mounting screws (Figure 8, item ). Figure Figure 8. Fasten brackets to support stand with mounting screws (Figure 8, item ), washers (Figure 8, item 5) and nuts (Figure 8, item 6). 5. Tighten screws (Figure 8, item & ) to 60 in-lb (7 Nm) Rev. C Dorner Mfg. Corp.

14 Installation 00 Series Mounting Brackets. Locate brackets. Exploded views shown in Figure 9. A WARNING Installing self-drilling screws into the DustPruf side rail requires substantial force. Failure to properly support the conveyor while installing self-drilling screws may cause the operator or conveyor to slip, causing severe injury. SUPPORT CONVEYOR FRAMES WHILE INSTALLING SELF-DRILLING SCREWS.. Measure an equal distance (Figure 0, item ) from end of head plate (on both sides of conveyor) and mark placement of mounting brackets (Figure 0, item ). Fasten mounting brackets to conveyor with mounting screws (Figure 0, item ) following proper methods of attachment instructions on page 0. Figure 0 Figure 9 Figure 0 5. Fasten brackets (Figure, item ) to support stand (Figure, item ) with mounting screws (Figure, item ), washers (Figure, item ) and connector bar (Figure, item 5). Figure 5 Figure 9. Remove screws (Figure 9, item ), washers (Figure 9, item ), and connector bar (Figure 9, item ) from brackets. Figure IMPORTANT For proper methods of attachment to conveyor side rail for 00 series see page 6.. Locate and retain self-drilling screws (Figure 9, item ). NOTE For maximum support distance see page 5. Dorner Mfg. Corp Rev. C

15 Installing Plastic Belt. Locate the conveyor belt retaining rod (Figure, item ). Installation. Feed belt into bottom wear strips (Figure, item ) and pull through to the far end. Figure Figure Figure. Align the belt grooves (Figure, item ) to the evenly spaced sprockets (Figure, item ) on the drive end of the conveyor. Figure Figure. Splice the belt together by pushing the plastic rod (Figure 5, item ) through the side hole on the rod retaining side of belt. Figure 5 Figure Figure Rev. C 5 Dorner Mfg. Corp.

16 Installation Proper Methods of Attachment to Side Rails (00 Series Only) The 00 DustPruf side rail is designed for self-drilling attachment of brackets and accessories. This can be done in two methods: self-drilling screws or pre-drill for standard screws. Self-Drilling Screws A WARNING Installing self-drilling screws into the dustpruf side rail requires substantial force. Failure to properly support the conveyor while installing self-drilling screws may cause the operator or conveyor to slip, causing severe injury. SUPPORT CONVEYOR FRAMES WHILE INSTALLING SELF-DRILLING SCREWS. All Dorner accessories are provided with /-0 self-drilling screws.. Locate and hold bracket (Figure 6, item ) to side rail. Hole should line up with notch (Figure 6, item ) in side rail. Figure 7 Figure 7 Pre-Drill for Standard Screws The DustPruf side rail will also accept standard screws. M6-.0 and /-0 are acceptable. Strength grade 8 is recommended.. Locate and hold bracket (Figure 8, item ) to side rail. Hole should line up with notch (Figure 8, item ) in side rail. Mark the hole locations with a center punch (Figure 8, item ) and remove the bracket. Figure 8 Figure 6 Figure 6. With a cordless drill or equivalent install self-drilling screws (Figure 6, item ). Use high speed setting to drill through side wall. Once the tap portion is started switch drill power to a lower speed. Do not fully tighten with drill.. Hand tighten the screws to secure (Figure 7). Recommended torque is 50 in.lbs (7 Nm). Figure 8. Drill the hole locations (Figure 9, item ) with a /6 drill bit (Figure 9, item ). Figure 9 Figure 9 Dorner Mfg. Corp Rev. C

17 . Position and hold bracket (Figure 0, item ) to side rail. With a standard M6-.0 or /-0 screw, install screws (Figure 0, item ) with cordless drill or equivalent. Do not fully tighten with drill. Figure 0 Figure 0. Hand tighten the screws to secure (Figure ). Recommended torque is 50 in.lbs (7 Nm). Figure Guiding (00 Series Only) A WARNING Installation Installing self-drilling screws into the DustPruf side rail requires substantial force. Failure to properly support the conveyor while installing self-drilling screws may cause the operator or conveyor to slip, causing severe injury. SUPPORT CONVEYOR FRAMES WHILE INSTALLING SELF-DRILLING SCREWS. Due to the DustPruf construction ALL guiding must be located and installed by the end user. Take care in locating retaining clips prior to final installation.. Lay out retaining clip (Figure, item ) locations. The end clips should be no greater than " (Figure, item ) from end of the conveyor. NOTE Profile -09, Low to High Side shown below. For other guide profile layouts see pages page 9 thru page. Figure 5 Figure Figure. Hold guide (Figure, item ) and retaining clips (Figure, item ) to conveyor side rail. Install selfdrilling screws (Figure, item 5) following the Proper Methods of Attachment to Side Rails (00 Series Only) on page 6 procedure Rev. C 7 Dorner Mfg. Corp.

18 Preventive Maintenance and Adjustment Required Tools Standard Tools Hex-key wrenches:.5 mm, mm, 5 mm / (. mm) wide Flat Blade screw driver Arbor press Adjustable wrench to (5 mm) wide Special Tools Sealed Bearing Removal Tool 509 Sealed Bearing Installation Tool Cleaning IMPORTANT Do not use belt cleaners that contain alcohol, acetone, Methyl Ethyl Ketone (MEK) or other harsh chemicals. Use Dorner Belt Cleaner. Mild soap and water may also be used. Do not soak the belt. Conveyor Belt Replacement A WARNING Checklist Keep service parts on hand (see Service Parts section for recommendations) Keep supply of belt cleaner Clean entire conveyor while disassembled Replace worn or damaged parts Lubrication No lubrication is required. Replace bearings if worn. Maintaining Conveyor Belt Troubleshooting Inspect conveyor belt for: Surface cuts or wear Tooth skipping Loose links Surface cuts and wear indicate: Sharp or heavy parts impacting belt Jammed parts Foreign material inside the conveyor Improperly positioned accessories Bolt-on guiding is pinching belt Stalling or skipping belt indicates: Belt stretching Conveyor belt or drive timing belt are not properly tensioned Worn sprocket or impacted dirt on drive pulley Intermittent jamming or drive train problems Conveyor Belt Replacement Sequence Remove old conveyor belt Install new conveyor belt Belt Removal. Choose one link on either end of the conveyor to remove belt pin. Locate end of rod without retaining feature (Figure, item ). Figure Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Figure Dorner Mfg. Corp Rev. C

19 Preventive Maintenance and Adjustment IMPORTANT You may need to slightly raise the underside of the conveyor belt to properly drive pin out of slots.. Pull back topside of belt to the drive end of the conveyor. See Figure 6. Figure 6. Insert punch (Figure, item ) into non-retaining side of belt, pushing rod out. Figure Figure 6 5. Remove belt by pulling belt out of bottom wear strips (Figure 7, item ). Figure 7 Figure. Remove rod (Figure 5, item ) and separate belt. Figure 5 Figure 7 Belt Installation. See Installing Plastic Belt page 5. Figure Rev. C 9 Dorner Mfg. Corp.

20 Preventive Maintenance and Adjustment Conveyor Belt Tension A WARNING A WARNING Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. NOTE The Modular Belt Conveyor is designed to operate with minimal belt tension. Conveyor will come with proper amount of belt sag at drive end of conveyor belt. See Figure 8. As belt stretches, it may be necessary to remove links to avoid too much belt sag. See Figure 9. Removal of Belt Links. Choose one link on either end of the conveyor to remove belt pin. Locate end of rod without retaining feature (Figure 0, item ). Figure 0 Operating conveyor with belt sag beyond maximum shown in Figure 9 will create belt pinch points which can cause injury. REMOVE BELT LINKS IF MAXIMUM SAG IS REACHED Figure 8 Figure 9 Figure 8 Figure 0 IMPORTANT You may need to slightly raise the underside of the conveyor belt to properly drive pin out of slots. Figure 9 Dorner Mfg. Corp Rev. C

21 Preventive Maintenance and Adjustment. Insert punch (Figure, item ) into non-retaining side of belt, pushing rod out. Figure 5. Splice the belt together by pushing the plastic rod (Figure, item ) through the side hole on the rod retaining side of belt. Figure Figure. Remove rod (Figure, item ) and separate belt. Figure Figure 6. Review belt sag at drive end to ensure it does not create a pinch point. If additional tensioning is required repeat steps through 5. Pulley and Sprockets Removal A WARNING Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Figure. Determine the number of links to be removed. Start with link and progress if additional tensioning is required repeat steps -. Remove conveyor belt to access pulley(s). See Conveyor Belt Replacement on page 8. Remove the desired pulley following the corresponding instructions below: A End Drive Conveyor B Center Drive Conveyor Rev. C Dorner Mfg. Corp.

22 Preventive Maintenance and Adjustment A End Drive Conveyor A WARNING. Use bearing removal tool ( ) (Figure 6, item ) to remove bearings from drive pulley. IMPORTANT You must replace with a new bearing after it is removed from shaft. Figure 6 Drive shaft keyway may be sharp. HANDLE WITH CARE.. On side of conveyor, remove two () fastening screws (Figure, item ). Figure Figure. Remove head plate (Figure 5, item ) and spindle (Figure 5, item ). Figure 5 Figure 6. Slide free moving sprocket(s) (Figure 7, item ) off the end of pulley (Figure 7, item ). Figure 7 Figure 7 Figure 5 Dorner Mfg. Corp Rev. C

23 B Center Drive Conveyor A WARNING Preventive Maintenance and Adjustment. Loosen and remove screw (Figure 9, item ) and bearing housing (Figure 9, item ) and remove drive pulley (Figure 9, item ). Figure 9. Loosen and remove two () fastening screws (Figure 8, item ) and clips (Figure 8, item ) on each side of conveyor to lower and remove center drive module (Figure 8, item ). Figure 8 Removing drive module without support under the module may lead to personel injury. PROVIDE SUPPORT UNDERNEATH THE DRIVE MODULE BEFORE REMOVING THE MODULE. Figure 9. Use bearing removal tool ( ) (Figure 0, item ) to remove bearings from drive pulley. IMPORTANT You must replace with a new bearing after it is removed from shaft. Figure 0 Figure 8 A WARNING Figure 0. Slide free moving sprocket(s) (Figure, item ) off the end of pulley (Figure, item ). Figure Drive shaft keyway may be sharp. HANDLE WITH CARE. Figure Rev. C Dorner Mfg. Corp.

24 Preventive Maintenance and Adjustment Bearing Removal & Replacement Removal IMPORTANT You must replace with a new bearing after it is removed from shaft.. Install pulley assembly (Figure, item ) on conveyor head plate (Figure, item ) and install opposite end head plate (Figure, item ). Figure. Remove drive pulley. For end drive pulley see section A End Drive Conveyor, steps through. For drive pulley see section B Center Drive Conveyor, steps through. Replacement. Inspect head plate bearing surface. If worn or damaged, replace head plate. See Service Parts on page 8. Pulley and Sprockets Replacement. Install required quantity of sprockets (Figure, item ) onto drive pulley (Figure, item ). Figure Figure. Install and tighten fastening screws (Figure 5, item ) to 60 in-lb (7 N m). Figure 5 Figure. Press new bearing onto drive pulley using installation tool 509 (Figure, item ). Figure Figure 5 Figure Dorner Mfg. Corp Rev. C

25 Preventive Maintenance and Adjustment Idler End Wear Items. Remove head plate (Figure 7, item ). Figure 7 A WARNING Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Remove conveyor belt to access pulley(s). See Conveyor Belt Replacement on page 8. Remove the desired pulley following the corresponding instructions below: A Standard Idler Tail B Nose Bar Idler Tail A - Standard Idler Tail. On one side of conveyor, remove one () fastening screw (Figure 6, item ). Figure 6 Figure 7. Slide tracking sleeves (Figure 8, item ), spacers (Figure 8, item ), and idler sleeves (Figure 8, item ) off the end of pulley (Figure 8, item ). Figure 8 Figure 6. On the same side of conveyor, remove two () fastening screws (Figure 6, item ). Figure Rev. C 5 Dorner Mfg. Corp.

26 Preventive Maintenance and Adjustment B - Nose Bar Idler Tail. On one side of conveyor, remove two () fastening screws (Figure 9, item ).. Remove head plate (Figure 5, item ). Figure 5 Figure 9 Figure 5. Remove tracking plate (Figure 5, item ), off the end of the bar and remove bar (Figure 5, item ). 5. Re-install bar (Figure 5, item ), making certain to only flip bar as shown below, and do not rotate. Bar should be level with conveyor as shown below. Figure 9. On the same side of conveyor, remove two () fastening screws (Figure 50, item ). NOTE Bar may be flipped 80 to use second wear surface (Figure 5, item ). Figure 50 Figure 5 Correct orientation Figure 5 Figure 50 Figure 5 Incorrect orientation Figure 5 Dorner Mfg. Corp Rev. C

27 Upper Wear Strip Replacement Preventive Maintenance and Adjustment 5. Install new wear strip (Figure 56, item ). Figure 56 A WARNING. Remove conveyor belt. See Belt Removal section on page 8.. With a putty knife (Figure 5, item ), start by raising edge of wear strip (Figure 5, item ). Figure 5 Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Figure Using a utility knife (Figure 56, item ), cut out notch in each corner (Figure 56, item ). Lower Wear Strip Replacement A WARNING Exposed moving parts can cause severe injury. LOCK OUT POWER before removing guards or performing maintenance. Figure 5. Remove old wear strip with a pliers (Figure 55, item ). Figure 55. Remove conveyor belt. See Belt Removal section on page 8.. Remove screw (Figure 57, item ) and sag guard plate (Figure 57, item ). Figure 57 5 Figure 55. Clean conveyor surface with isopropyl alcohol and allow to fully dry. Figure 57. Remove screw(s) (Figure 57, item ) from each retaining clip (Figure 57, item ), and remove lower wear strip (Figure 57, item 5).. Clean conveyor surface with isopropyl alcohol and allow to fully dry. 5. Install new wear strip and secure with retaining clips. 6. Install sag guard plate with screw Rev. C 7 Dorner Mfg. Corp.

28 Service Parts Drive End NOTE For replacement parts other than those shown in this section, contact an authorized Dorner Service Center or the factory. Key Service Parts and Kits are identified by the Performance Parts Kits logo. Dorner recommends keeping these parts on hand. Drive Spindle Kit Sprocket Kit Dual Shaft Option 5 Dorner Mfg. Corp Rev. C

29 Service Parts Sprocket 08 Drive Tracking Block 0-WW Drive Spindle 098-WW Dual Shaft Drive Spindle 0-WW Square Key /6" * 5 BK Bearing Kit ( pack) 6 09 Tension Slide Bar (00 Series Only) 706 Tension Slide Bar (00 Series Only) 7 06 Right Hand Head Plate, for A & B Position 08 Right Hand Head Plate, for C & D Position 8 07 Left Hand Drive Plate, for A & B Position 05 Left Hand Drive Head, for C & D Position M Low Head Cap Screw, M x 0 mm M Low Head Cap Screw, M x mm (00 Series Only) 95060M Low Head Cap Screw, M x 0 mm (00 Series Only) 9706M Cup Set Screw, M x mm 980M Square Key, mm x mm XMBDS-WW Drive Spindle Kit (Includes items,,, 5, 9 and 0) XMBDDS-WW Drive Spindle Kit - Dual Shaft (Includes items,,, 5, 9 and 0) XMBS-WW Sprocket Kit (Includes items and ) WW = Conveyor width reference: 0, 08, & * wide - uses two Rev. C 9 Dorner Mfg. Corp.

30 Service Parts Idler End 8 Idler Spindle Kit Idler Sleeve 00 Idler Side Plate 0 Tracking Sleeve 0-WW Idler Shaft 5 0-WW Idler Spacer 6 09 Tension Slide Bar (00 Series Only) 706 Tension Slide Bar (00 Series Only) M Low Head Cap Screw, M x mm (00 Series Only) 95060M Low Head Cap Screw, M x 0 mm (00 Series Only) 8 XMBT-WW Idler Spindle Kit (Includes items, and 5) WW = Conveyor width reference: 0, 08, & Dorner Mfg. Corp Rev. C

31 Nose Bar Idler End Service Parts 7 Nose Bar Spindle Kit Tracking Plate 06 Idler Side Plate 09-WW Nosebar Assembly 09 Tension Slide Bar (00 Series Only) 706 Tension Slide Bar (00 Series Only) M Socket Head Screw, M x 6 mm M Low Head Cap Screw, M x mm (00 Series Only) 95060M Low Head Cap Screw, M x 0 mm (00 Series Only) 7 XMBNB-WW NoseBar Spindle Kit, (Includes items and ) WW = Conveyor width reference: 0, 08, & Rev. C Dorner Mfg. Corp.

32 Service Parts Center Drive Module Center Drive Kit Dorner Mfg. Corp Rev. C

33 Service Parts Bearing Cam Sprocket Plug 07 Bearing Housing 5 06 Drive Side Bearing Housing 6 09 Center Drive Plate Short Center Drive Plate WW Center Drive Extrusion WW Takeup Shaft WW Wear Strip Guard 099 Center Clip Left Hand 000 Center Clip Right Hand 00 Idler Sleeve 07 Guard Mount Bracket 5 0-WW Idler Spacer 6 0-WW Drive Spindle 7 0-WW Square Key /6 * 8 BK Bearing Kit ( pack) BK Bearing Kit ( pack) M Drive Guard 0 090M Nut, Cam Follower 8-0 Timing Belt, 5 mm Wide x 85 mm Long 8-00 Timing Belt, 5 mm Wide x 00 mm Long Timing Belt, 5 mm Wide x 5 mm Long 8-05 Timing Belt, 5 mm Wide x 60 mm Long 5065MP Driven Pulley, 9 Tooth 5066MP Driven Pulley, Tooth 5067MP Driven Pulley, 8 Tooth 5068MP Driven Pulley, Tooth 980M Square Key, mm x mm 50 Drive Pulley, Tooth (for parallel shaft gearmotors) 505 Drive Pulley, 8 Tooth (for parallel shaft gearmotors) 506 Drive Pulley, Tooth (for parallel shaft gearmotors) 507 Drive Pulley, Tooth (for parallel shaft gearmotors) 508 Drive Pulley, 8 Tooth (for parallel shaft gearmotors) 509 Drive Pulley, 60 Tooth (for parallel shaft gearmotors) 5065MP Drive Pulley, 9 Tooth (for 90 gearmotors) 5066MP Drive Pulley, Tooth (for 90 gearmotors) 5067MP Drive Pulley, 8 Tooth (for 90 gearmotors) 5068MP Drive Pulley, Tooth (for 90 gearmotors) 5069MP Drive Pulley, Tooth (for 90 gearmotors) 5070MP Drive Pulley, 8 Tooth (for 90 gearmotors) 507MP Drive Pulley, 60 Tooth (for 90 gearmotors) Square Key 0.88" x 0.75" (for parallel shaft gearmotors) 980M Square Key mm x mm (for 90 gearmotors) P Socket Head Screw, M x 5 mm M Socket Head Screw, M x6 mm M Socket Head Screw, M x 8 mm M Low Head Cap Screw, M x 0 mm M Low Head Cap Screw, M x mm 95060M Low Head Cap Screw, M x 0 mm 9085M Socket Head Screw, M8 -.5 x 5 mm XMBCD-WW Center Drive Kit, (Includes items,, 5, 6, 7 an d8) Socket Head Screw, /-8 x 0.75 for parallel shaft gearmotors 9065M Socket Head Screw, M x 5 mm (for standard load 90 gearmotors) 9060M Socket Head Screw, M x 0 mm (for heavy load 90 gearmotors) 5 07 Drive Shaft (for E-Drive CZ C Face Gearmotors) 50 Drive Shaft (for E-Drive 56 C Face Gearmotors) Drive-Bearing Shaft Cover (for E- Drive CZ C Face Gearmotors) Drive-Bearing Shaft Cover (for E- Drive 56 C Face, IEC 6B5 and IEC 7B5 Gearmotors) Adapter (for E-Drive CZ C Face Gearmotors) 505 Adapter (for E-Drive 56 C Face Gearmotors) Square Key, 0.88" x.50" M Low Head Cap Screw, M8-.5 x 6 mm (for E-Drive CZ C Face Gearmotors) 900MSS Flat Head Screw M0-.50 x 0 mm (for E-Drive 56 C Face Gearmotors) P Washer 906M Socket Head Screw, M6-.00 x mm WW = Conveyor width ref.: 0, 08,, & * wide - uses two Rev. C Dorner Mfg. Corp.

34 Service Parts Parallel Shaft Gearmotors 90 Gearmotors 6M80PSFN Motor, 0.08hp (0.06Kw), 0 RPM, 5VAC, 60Hz, -Phase 6M060PSFN Motor, 0.7hp (0.Kw), 9 RPM, 5VAC, 60Hz, -Phase 6M060PSEN Motor, 0.7hp (0.Kw), 9 RPM, 0/60 Volts, 0-60Hz, -Phase 6M060PSFN Motor, 0.5hp (0.9Kw), 9 RPM, 0VAC, 60Hz, -Phase 6M00PSFN Motor, 0.7hp (0.Kw), 58 RPM, 5VAC, 60Hz, -Phase 6M00PSEN Motor, 0.8hp (0.8Kw), 58 RPM, 0/60 Volt, 0-60Hz, -Phase 6M00PSFN Motor, 0.5hp (0.9Kw), 58 RPM, 0VAC, 60Hz, -Phase 6M00PSFN Motor, 0.7hp (0.Kw), 86 RPM, 5VAC, 60Hz, -Phase 6M00PSEN Motor, 0.8hp (0.8Kw), 86 RPM, 0/60 Volt, 0-60Hz, -Phase 6M00PSFN Motor, 0.7hp (0.Kw), 7 RPM, 5VAC, 60Hz, -Phase 6M00PSEN Motor, 0.8hp (0.8Kw), 7 RPM, 0/60 Volt, 0-60Hz, -Phase 6M00PSFN Motor, 0.5hp (0.9Kw), 7 RPM, 0VAC, 60Hz, -Phase 6M005PSFN Motor, 0.7hp (0.Kw), 5 RPM, 5VAC, 60Hz, -Phase 6M005PSEN Motor, 0.8hp (0.8Kw), 5 RPM, 0/60 Volt, 0-60Hz, -Phase 6M80PSDDEN Motor, 0.hp (0.09Kw), RPM, 0VDC 6M060PSDDEN Motor, 0.5hp (0.9Kw), RPM, 0VDC 6M00PSDDEN Motor, 0.5hp (0.9Kw), 8 RPM, 0VDC 6M00PSDDEN Motor, 0.5hp (0.9Kw), 5 RPM, 0VDC 6M00PSDDEN Motor, 0.5hp (0.9Kw), 50 RPM, 0VDC 6M005PSDDEN Motor, 0.5hp (0.9Kw), 500 RPM, 0VDC 6MESFN Motor, 0.5HP, (0.9 Kw), 5/0 Volts, 60 Hz, -Phase 6MESFN Motor, 0.5HP, (0.9 Kw), 08-0/60 Volts, 60 Hz, -Phase 6MSDDEN Motor, 0.5HP, (0.9 Kw), 0 VDC 6MEHFN Motor, 0.50HP, (0.7 Kw), 5/0 Volts, 60 Hz, -Phase, non-reversing 6MEHFN Motor, 0.50HP, (0.7 Kw), 5/0 Volts, 60 Hz, -Phase MEHFN Motor, 0.50HP, (0.7 Kw), 08-0/60 Volts, 60 Hz, -Phase 6MHD9DEN Motor, 0.50HP, (0.7 Kw), 90 VDC MESEN Motor, 0.50HP, (0.7 Kw), 0 Volts, - Phase Inverter Duty M005EL Gear Reducer, 5:, NEMA CZ M00EL Gear Reducer, 0:, NEMA CZ M00EL Gear Reducer, 0:, NEMA CZ M00EL Gear Reducer, 0:, NEMA CZ M060EL Gear Reducer, 60:, NEMA CZ M005ES Gear Reducer, 5:, 56C M00ES Gear Reducer, 0:, 56C M00ES Gear Reducer, 0:, 56C M00ES Gear Reducer, 0:, 56C M060ES Gear Reducer, 60:, 56C Dorner Mfg. Corp Rev. C

35 Service Parts 00 Series Frame Assembly Flat Head Screw, M x 0 mm UHMW Tape.65" for " Wide Conveyors UHMW Tape.50" for 8" Wide Conveyors UHMW Tape 5.75" for " & " Wide Conveyors 00-WW-LLLLL Bed Plate for Single Piece Frames 09-WW-LLLLL End Bed Plate for Multi Piece Frames 09-WW-LLLLL Mid Bed Plate for Multi Piece Frames 09-WW-LLLLL Bottom Bed Plate 5 0-LLLLL Frame Rail 6 05-LLLLL Center Rail for 8", " & " Wide Conveyors Center Cross Rail for " Wide Conveyors WW = Conveyor width reference: 0, 08, & LLLLL = Part length in inches with decimal places. Example: Part Length = 95.5" LLLLL = Rev. C 5 Dorner Mfg. Corp.

36 Service Parts 00 Series Frame Assembly Flat Head Screw, M x 0 mm UHMW Tape.65" for " Wide Conveyors UHMW Tape.50" for 8" Wide Conveyors UHMW Tape 5.75" for " & " Wide Conveyors 00-WW-LLLLL Bed Plate for Single Piece Frames 09-WW-LLLLL End Bed Plate for Multi Piece Frames 09-WW-LLLLL Mid Bed Plate for Multi Piece Frames 09-WW-LLLLL Bottom Bed Plate 5 08-WW Frame Cap Plate, for ", 8", & " Wide Conveyors LLLLL Frame Rail for Single Piece Frames 707L-LLLLL Left Hand End Frame Rail for Multi Piece Frames 707R-LLLLL Right Hand End Frame Rail for Multi Piece Frames 706-LLLLL Mid Frame Rail for Multi Piece Frames 7 05-LLLLL Center Rail for 8", " & " Wide Conveyors Center Cross Rail for " Wide Conveyors WW = Conveyor width reference: 0, 08, & LLLLL = Part length in inches with decimal places. Example: Part Length = 95.5" LLLLL = 0955 Dorner Mfg. Corp Rev. C

37 Service Parts Connecting Assembly without Stand Mounts 0859 Connecting Plate 0858 Connecting Bar (00 Series Only) 70 Connecting Bar (00 Series Only) 9506M Low Head Cap Screw, M x mm Connecting Assembly with Mounting Brackets Connector Bar 09 Stand Mount 0858 Connecting Bar (00 Series Only) 70 Connecting Bar (00 Series Only) 60579P Washer M Socket Head Screw, M x 0 mm M Low Head Cap Screw, M x mm Rev. C 7 Dorner Mfg. Corp.

38 Service Parts Return Wear Strip Sheet Metal Screw, # x LLLLL Return Wear Strip 09 Retaining Clip 0 Sag Guard Plate Left Hand 5 0 Sag Guard Plate Right Hand LLLLL = Part length in inches with decimal places. Example: Part Length = 95.5" LLLLL = 0955 Dorner Mfg. Corp Rev. C

39 -0 Low Side Service Parts 00 Guide Retaining Clip 055-LLLLL Low Side Guides 6997MK0 Single Drop-in Tee Bar (00 Series Only) (x0) 95060M Low Head Cap Screw, M x 0 mm (00 Series Only) Self-Drilling Hex Head Screw, / - 0 x " (00 Series Only) LLLLL = Part length in inches with decimal places. Example: Part Length = 95.5" LLLLL = Rev. C 9 Dorner Mfg. Corp.

40 Service Parts 0 (76 mm) Aluminum Side 00 Guide Retaining Clip 800-LLLLL (76 mm) High Side Guides 6997MK0 Single Drop in Tee Bar (00 Series Only) (x0) 95060M Low Head Cap Screw, M6 x 0 mm (00 Series) Self-Drilling Hex Head Screw, /-0x (00 Series) LLLLL = Part length in inches with decimal places. Example: Part Length = 5.5" LLLLL = 055 Dorner Mfg. Corp Rev. C

41 05.5 (8 mm) Aluminum Side Service Parts 00 Guide Retaining Clip 8050-LLLLL.5 (8 mm) High Side Guides 6997MK0 Single Drop in Tee Bar (00 Series Only) (x0) 95060M Low Head Cap Screw, M6 x 0 mm (00 Series) Self-Drilling Hex Head Screw, /-0x (00 Series) LLLLL = Part length in inches with decimal places. Example: Part Length = 5.5" LLLLL = Rev. C Dorner Mfg. Corp.

42 Service Parts 09 Low to High Side 00 Guide Retaining Clip 8090-LLLLL 0.5 ( mm) High Side Guides 6997MK0 Single Drop in Tee Bar (00 Series Only) (x0) 95060M Low Head Cap Screw, M6 x 0 mm (00 Series) Self-Drilling Hex Head Screw, /-0x (00 Series) LLLLL = Part length in inches with decimal places. Example: Part Length = 5.5" LLLLL = 055 Dorner Mfg. Corp Rev. C

43 Service Parts Adjustable Guiding LLLLL Aluminum Profile Guide 0080M Drop In Tee Bar (00 Series Only) 000 Mounting Bracket 007M Guide Mounting Shaft Vertical 5 008M Guide Mounting Shaft Horizontal MP Square Nut Cross Block Vinyl Shaft Cap P Flat Extruded Guide (per foot) 0 906M Socket Head Screw, M6 x mm (00 Series) Self-Drilling Hex Head Screw, /-0x (00 Series) 9066M Socket Head Screw, M6 x 6 mm LLLLL = Part length in inches with decimal places. Example: Part Length = 5.5" LLLLL = Rev. C Dorner Mfg. Corp.

44 Service Parts Tool-Less Adjustable Guiding Shaft Cap Cross Block 0080M Drop-In Tee Bar (00 Series Only) 000M Mounting Bracket 5 007M Vertical Mounting Guide Shaft 6 008M Horizontal Mounting Guide Shaft MP Square Nut, M M Socket Head Screw, M6-.00 x mm (00 Series) Self-Drilling Hex Head Screw, /-0x (00 Series) M Socket Head Screw, M6-.00 x 6 mm LLLLL Aluminum Profile Guide 6068P-LLLLL Extruded Guide LLLLL = Part length in inches with decimal places. Example: Part Length = 95.5" LLLLL = 0955 Dorner Mfg. Corp Rev. C

45 Service Parts Mounting Brackets Connector Bar 09 Stand Mount 0050M Drop-in Tee Bar (00 Series Only) 60579P Washer M Socket Head Screw, M x 0 mm M Low Head Cap Screw, M x mm (00 Series Only) Self-Drilling Hex Head Screw, / - 0 x " (00 Series Only) Mounting Brackets for (60 mm) Conveyors Connector Bar 00 ' Stand Mount Left Hand 005 ' Stand Mount Right Hand 6997M Drop-in Tee Bar (00 Series Only) P Washer M Socket Head Screw, M x 0 mm M Low Head Cap Screw, M x mm (00 Series Only) Self-Drilling Hex Head Screw, / - 0 x " (00 Series Only) Rev. C 5 Dorner Mfg. Corp.

46 Service Parts Mounting Brackets for Short Center Drive Conveyors Stand Mount 6997M Drop-in Tee Bar 60579P Washer 9060M Socket Head Screw, M x 0 mm M Low Head Cap Screw, M x 5 mm Conveyor Belting Belting Per Foot (05 mm) Figure 58 Figure Belt Rod Belt Rod Belt Rod Belt Rod P WW/0 Belting per ft (05mm) WW=Width: 0, 08,, Dorner Mfg. Corp Rev. C

47 Notes Rev. C 7 Dorner Mfg. Corp.

48 Return Policy Returns must have prior written factory authorization or they will not be accepted. Items that are returned to Dorner without authorization will not be credited nor returned to the original sender. When calling for authorization, please have the following information ready for the Dorner factory representative or your local distributor:. Name and address of customer.. Dorner part number(s) of item(s) being returned.. Reason for return.. Customer's original order number used when ordering the item(s). 5. Dorner or distributor invoice number (if available, part serial number). A representative will discuss action to be taken on the returned items and provide a Returned Goods Authorization (RMA) number for reference. RMA will automatically close 0 days after being issued. To get credit, items must be new and undamaged. There will be a return charge on all items returned for credit, where Dorner was not at fault. It is the customer s responsibility to prevent damage during return shipping. Damaged or modified items will not be accepted. The customer is responsible for return freight. Product Line 00 Conveyors Gearmotors & Mounting Packages Support Stands Product Type Standard Products Accessories Spare Parts (non-belt) Spare Belts - Standard Flat Fabric Spare Belts - Cleated & Specialty Fabric Spare Belts - Plastic Chain Engineered to order parts All equipment and parts Modular Belt 00 Precision Move Modular Belt 00 0% return fee for all products except: 50% return fee for conveyors with modular belt, 00 LPZ cleated belt or specialty belts non-returnable case-by-case 00 Precision Move Controls 700 / % return fee for all products non-returnable Returns will not be accepted after 60 days from original invoice date. The return charge covers inspection, cleaning, disassembly, disposal and reissuing of components to inventory. If a replacement is needed prior to evaluation of returned item, a purchase order must be issued. Credit (if any) is issued only after return and evaluation is complete. Dorner has representatives throughout the world. Contact Dorner for the name of your local representative. Our Customer Service Team will gladly help with your questions on Dorner products. For a copy of Dorner's Warranty, contact factory, distributor, service center or visit our website at For replacement parts, contact an authorized Dorner Service Center or the factory. Dorner Mfg. Corp. reserves the right to change or discontinue products without notice. All products and services are covered in accordance with our standard warranty. All rights reserved. Dorner Mfg. Corp. 05 DORNER MFG. CORP. 975 Cottonwood Ave., PO Box 0 Hartland, WI USA TEL (USA) FAX (USA) Internet: Outside the USA: TEL FAX Rev. C Printed in U.S.A.