MEMSTYLE. SPECTRA Modules range TECHNICAL INFORMATION

Size: px

Start display at page:

Download "MEMSTYLE. SPECTRA Modules range TECHNICAL INFORMATION"

Georgina Johnston
5 years ago
Views:

1 SPECT Modules range TECHNICL INFOMTION

2 SPECT Modules range Coverplate, Grid and Mounting Box Selection Guide GNG rchitrave COVE PLTES INT WHITE MOLDED M801 M802 M803 M804 M806 M808 LT FLT METL* FLSH METL STINLESS STEEL/MTT CHOME 801SS 802SS 803SS 804SS 806SS 808SS 809SS 812SS 818SS 824SS 800SS STIN BONZE 801SB 802SB 803SB 804SB 806SB 808SB 809SB 812SB 818SB 824SB 800SB HIGHLY POLISHED 801HP 802HP 803HP 804HP 806HP 808HP 809HP 812HP 818HP 824HP 800HP - MONCH BSS 801MB 802MB 803MB 804MB XT - SFCE METL X801MG X802MG X803MG X804MG X806MG X808MG X809MG X812MG X818MG X824MG COVE PLTE DIMENSIONS (mm) LT - FLT METL 86x86 86x86 86x146 86x x x x x x x279 XT - SFCE METL 86x86 86x86 86x146 86x x x x x x x256 - MONCH BSS 96x96 96x96 96x158 96x158 LL OTHE FINISHES 89x89 89x89 89x146 89x x x x x x x279 38x116 GIDS, SFCE O FLSH MONTING 1xF8100 1xF8100 1xF8101 1xF8101 2xF8101 2xF8101 3xF8101 3xF8101 3xF8102 4xF8102 F8103 STEEL BOXES, SFCE O FLSH MONTING WITH KNOCKOTS FM8340 FM8340 FM8341 FM8341 F8342 F8342 F8343 F8343 F8344 F8345 WITHOT KNOCKOTS FM8349 FM8349 FM8350 FM8350 F8351 F8351 F8352 F8352 DIMENSIONS (mm) FM8340 FM8340 FM8341 FM8341 F8342 F8342 F8343 F8343 F8344 F x79x79 41x79x79 41x79x139 41x79x139 41x134x134 41x134x134 41x134x195 41x134x195 56x195x195 56x254x195 STEEL BOXES, FLSH MONTING (35mm deep) H - 100mm W - 28mm D - 30mm F8368 F8368 F8367 F8367 F8330 MOLDED PTTESS FO SFCE MONTING WHITE MOLDED PLTES (28mm deep) F4501 F4501 F4502 F4502 * dd plate finish reference to complete order ie. 801SS

SPECT Modules range Grid Technical Data Grid Installing grid couldn t be easier. Just follow these simple instructions. 1.

Squeeze the ends of the module together to ensure that the switch has snapped on to the grid. No retaining screw or clip necessary. 1. 2. 3.

ll grid modules have wide terminal mouths able to take up to 3 x 2.5mm 2 cable.

When the screws are fully tightened the grid is automatically positioned correctly for mounting the front plate.

flush mounting. 3. 4. 6. ttach the cover plate to the grid using the screws provided with the cover plate. 5. 6. Standard grid modules Current ating: 10 or 20 - X-rated for fluorescent/ or inductive loads.

F8085 lounge entrance alarm press toilet reception kitchen heater ladies spots bell fan gents garage push water heater lights emergency bar

3 SPECT Modules range Grid Technical Data Grid Installing grid couldn t be easier. Just follow these simple instructions. 1. Push each module on to the grid, after preparing the cable tails in the mounting box. 2. Squeeze the ends of the module together to ensure that the switch has snapped on to the grid. No retaining screw or clip necessary Push hard on the switch to check that the ends have clipped firmly on to the grid. 4. Wire each individual switch module. ll grid modules have wide terminal mouths able to take up to 3 x 2.5mm 2 cable. The module reference number function and circuit diagram is printed clearly on the reverse for easy reference. 5. When the screws are fully tightened the grid is automatically positioned correctly for mounting the front plate. For metalclad surface applications remove the end clamps before screwing the grid to the mounting applications follow the instructions for flush mounting ttach the cover plate to the grid using the screws provided with the cover plate Standard grid modules Current ating: 10 or 20 - X-rated for fluorescent/ or inductive loads. Voltage ating: 240V.C. 50Hz vailable labels for the window grid switch Labels can be ordered ref. F8085 lounge entrance alarm press toilet reception kitchen heater ladies spots bell fan gents garage push water heater lights emergency bar stairway Installation of label and window for window grid switch Pre-printed labels and blanks are available separately (ref. F8085) Once clipped into place the transparent windows are NOT designed to be removed from the switch module. The window can be affixed prior to the mounting of the cover plate or afterwards.

4 SPECT Modules range Grid Technical Data Grid Dimmer Modules Product Lighting Minimum Maximum Grid Spaces Code Type Load Load equired No. of Ways F8064 Tungsten 40W 250W 1 gang 2W F8065 Tungsten 80W 400W 1 gang 2W * For ballasts a contactor will also be required. Note: ef. F8066 and F8069 take up two modules, (two gangs) in the grid system and are supplied with a blank module ef. F8060. F8066 Tungsten 100W 630W 2 gang 2W 1 blank req. F8067 Low voltage 50V 250V 1 gang 2W F8068 Low voltage 50V 400V 1 gang 2W F8069 Fluorescent 60W 400W 2 gang 2W mains dimming 1 blank req. F8078 Fluorescent 1-10V 10/50 ballasts* 1 gang 2W ballasts plus switch req. F8083 Grid assembly for commercial dimming system Loading ules Table Dimmers can be mounted in the same enclosure providing the total wattage (V) loading being used is within the following guidelines: No. of grid gangs Max. wattage per row Max total plate wattage Grid Dimmer Wiring and Set-p. Tungsten - ef. F8064, F8065, F8066 One way switching - may go to terminal L1 or L2. Two way switching - se both terminals. Note: that there are two methods for 2-way wiring, only one dimmer can be wired in each circuit (this dimmer may be fitted in either position). For dimming 230V Tungsten Halogen Lamps, de-rate dimmer by 50% (eg. F8065 maximum load becomes 200W). 1-Way Wiring Grid Dimmer L1 L2 Variable Standard 2-Way Wiring lternative 2-Way Wiring Method Grid Dimmer Mechanical Switch Grid Dimmer Mechanical Switch Variable Common (C) Common (C) L1 L2 COM L1 L2 L1 L2 COM L1 L2 Variable (Note, for 2-way circuit, dimmer & switch may be swapped) Fig. 4 B. Low Voltage Lighting - ef. F8067, F8068 These Dimmers are for controlling wire-wound laminated and some compatible dimmable electronic transformers Note: they are not suitable for use with toroidal transformers. Wire as for Tungsten Lighting, with the Variable to the Fig V side of the transformer. The Dimmer V rating represents maximum circuit load. llow for Transformer Losses, typically 20% (15% for dimmable electronic transformers) i.e. maximum lamp load for 400V Dimmer becomes 333W (347W for electronic), and 200V becomes 208W (216W for electronic). ny mixture of transformer sizes may be used, providing maximum dimmer rating is not exceeded. ll Eaton s MEM Grid Dimmers are leading edge dimmers. These are not compatible with transformers which require a trailing edge, phase-cutting or falling edge type dimmer. fter installation and restoring power, move slider to minimum light, then adjust dimmer for desired maximum light level (normally 20% light) ensuring that the light output is flicker free. (see fig.5) C. Fluorescent Lighting - ef. F8069 F EL-FD Control Gear Dimmer F DT Control Gear L1 L N L2 COM F1 Load esistors Switched Variable L Fluorescent Lamp N DT or niversal Dimming Transformer Ballast Typical wiring for dimmer 50Hz flu fittings. Fig. 6 Typical wiring for dimmable high frequency flu fittings 28-45Hz which require mains dimming. Fluorescent Tube Dimmer 8069 L1 L2 COM F1 EL-FD HF Ballast Filter Choke Filter Choke L Variable N Fig. 7 Load esistors Note: To overcome lamp flicker, load resistors have to be fitted across the variable live output (Com) and neutral. One load resistor is required for each ballast. Warning: se of lower than minimum loads with fluorescent dimmers will result in damage to the unit.

5 SPECT Modules range Quick Options Guide OPTIONS STNDD NGE 1 Gang 1 Gang 2 Gang 3 Gang 4 Gang 1 Gang 2 Gang 3 Gang Fan 3 Pole 1 Way 2 Way 2 Way 2 Way 2 Way Intermed. 1 Way 1 Way Isolator Isolator Switch Switch Switch Switch Switch Switch Switch Switch Switch Switch INT M011 M021 M022 M023 M024 M017 M012 M013 M048 M049 LT 021* 022* 023* 017* 048* 049* STINLESS STEEL 021SS 022SS 023SS O17SS 048SS 049SS NCOTED STINLESS STEEL 021S 022S O23S 017S STIN BONZE 021SB 022SB 023SB 017SB 048SB 049SB HIGHLY POLISHED 021HP 022HP 023HP 017HP O48HP 049HP XT X021MG X022MG X023MG X017MG X048MG X049MG MONCH BSS 021MB 022MB 023MB 017MB 048MB 049MB OPTIONS STNDD NGE 4 Gang 1 Gang 6 Gang 1 Gang 2 Gang 1 Gang 1 Gang 1 Way Bell Push 2 Way 2 Way 2 Way Light 1 Way Switch Switch Switch rchitrave rchitrave Symbol rchitrave INT M014 M015 M026 M021 M022 M015L M011 LT 015* 026* STINLESS STEEL NCOTED STINLESS STEEL STIN BONZE HIGHLY POLISHED 015SS 015S 015SB 015HP XT MONCH BSS X015MG 015MB 1 Gang 2 Gang 1 Gang 1 Gang 1 Gang 1 Gang Double Double 2 Gang 4 Gang BOD MODLE NGE 2 Way 2 Way Half Bell Push Intermed. 2 Way Half Intermed. Pole Pole with 2 Way 2 Way Half Switch Module Switch Switch Module Half Module Switch Neon Switch Module INT M041 M032 M045 M047 M031 M037 M043 M043N M042 M034 LT 032* 031* STINLESS STEEL 041SS 032SS 045SS 047SS 031SS 037SS 043SS 043NSS STIN BONZE 041SB 032SB 045SB 047SB 031SB 037SB 043SB 043NSB HIGHLY POLISHED 041HP 032HP 045HP 047HP 031HP 037HP 043HP 043NHP XT X041MG X032MG X045MG X047MG X031MG X037MG X043MG X043NMG MONCH BSS 041MB 032MB 045MB 047MB 031MB 037MB 043MB 043NMB OPTIONS FCEPLTES 1 Gang 2 Gang 3 Gang Half Broad 6 Gang Plate Plate Plate Plate Plate INT M861 M862 M863 M871 M866 STINLESS STEEL 861SS 862SS 863SS 871SS 866SS STIN BONZE 861SB 862SB 863SB 871SB 866SB HIGHLY POLISHED 861HP 862HP 863HP 871HP 866HP XT X861MG X862MG X863MG X871MG X866MG MONCH BSS 861MB 862MB 863MB 871MB 866MB *To order LT product finish please use existing ref. no. and add any suffix from list below: Finishes available are: SS Stainless Steel PB Polished Brass WH White N nodised Silver HP Highly Polished B ntique Bronze SB Satin Bronze C ntique Copper BS Brass Satin MG Metallic Grey * To order your chosen product with a Black insert use guide below: 1. se existing ref. no. 2. dd B to the end of ref. no. indicating insert eg. 021B 3. Finally add plate finish ref. ie. SS to complete order ref. no. eg. 021BSS

SPECT Modules range Voice/Data coverplate selection guide Voice/Data Quick eference Chart GNG 1 2 4 COVEPLTES INT M851 M852 M854 PLTE DIMENSIONS (mm) 86x86 86x86 86x146 STINLESS STEEL/MTT CHOME 851SS

6 SPECT Modules range Voice/Data coverplate selection guide Voice/Data Quick eference Chart GNG COVEPLTES INT M851 M852 M854 PLTE DIMENSIONS (mm) 86x86 86x86 86x146 STINLESS STEEL/MTT CHOME 851SS 852SS 854SS HIGHLY POLISHED 851HP 852HP 854HP STIN BONZE 851SB 852HP 854HP PLTE DIMENSIONS (mm) 89x89 89x89 89x146 MONCH BSS 851MB 852MB 854MB PLTE DIMENSIONS (mm) 96x96 96x96 96x158 LT 851* 852* 854* PLTE DIMENSIONS (mm) 86x86 86x86 86x146 XT X851MG X852MG X854MG PLTE DIMENSIONS (mm) 86x86 86x86 86x146 * To order LT product finish please use existing ref. no and add any suffix from list below: Finishes available are: SS Stainless Steel WH White HP Highly Polished SB Satin Bronze BS Brass Satin PB Polished Brass N nodised Silver B ntique Bronze C ntique Copper MG Metallic Grey In floor box applications Voice/Data modules can be mounted to flat metal or plastic wall plate and in this case a minimum clearance of 20mm is required behind the plate. ef: F3691 is CT 5E compliant unless otherwise stated. They are suitable for use with wall plates in boxes of only 16mm depth.

Grid Plus Modular Switch System

Grid Plus Modular Switch System 1:6 Grid Plus Modular Switch System PRODUCT RANGE For full product range, please refer to tables on pages 2:6, 3.6 and listing on page 4:6 Standards and approvals Switch