PROTECTA III. Construction Tough glass reinforced polyester body

Transcription

1 PROTECTA III 20 Construction Tough glass reinforced polyester body Polycarbonate diffuser with high resistance to UV and stress cracking Robust hinges and multipoint compressive clamping of diffuser closure EPDM gasket with sealing lip Bolted through suspension points for great strength IP66/IP67 and deluge tested to DTS-01 Bolted through suspension points & fully compressed gasket Protecta with diffuser opened Easy access to lamps & control gear Quick release mains terminals to ballast & battery for ease of maintenance Reverse side of gear tray Reliability Robust electronics with End of Life (EOL) protection to IEC with EOL I and EOL II functionality Outstanding electrical immunity to mains disturbances including over-voltage, harmonics and spikes Vibration tested to DNV/Lloyds requirements Functional 9 minute self test every 13 days with full discharge and recharge self test every 3 months Comprehensive charge and discharge control management for maximum battery life Continuous monitoring of charge and function with fault indication and diagnosis Temperature resistant Ni-Cd battery technology

2 KEY FEATURES 21 Performance Automatic commissioning of emergency versions Regulated output, light is constant over full supply voltage range Very high electrical efficiency > 92% Excellent light output in emergency operation: 18W = 50% of one lamp, 36W = 45% of one lamp (/HEO option) Optional 3 hour emergency duration to EN Rapid recharge to 80% capacity Universal Remote Emergency Inhibition can be used with other pre-existing systems Relative light 120% 110% 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0% Chalmit Ex e Protecta Chalmit Exe e Protecta vs Competitor Exe e Product Competitor Ex e Product Ambient (ºC) 20% greater light output at -20 C compared to other manufacturers Bi-colour LED indication Patented automatic lamp de-energisation on opening Quick release mains terminals Installation and Maintenance Standard fixing centres All parts mounted on gear tray, can be quickly removed leaving an Ex safe configuration Screwless mains terminals for rapid connection, no need for periodic checks Plug and socket battery connection for quick connection guaranteeing correct polarity Can be voltage tested with suitable current limited instruments Emergency lamp fault detection before the lamp becomes un-serviceable Self testing of battery capacity with low capacity LED indication Patented automatic lamp de-energisation on opening Common spare parts across Ex e fluorescent range (Protecta, Acclaim, Curie Elite) Screwed connection (optional)

3 PROTECTA III Ex e FLUORESCENT 22 The Protecta III is a proven and reliable T8 fluorescent luminaire. The Protecta s rugged, corrosion resistant construction (IP66/IP67) combined with an advanced high frequency ballast ensure minimum product maintenance is required. When access is required the Protecta III features an easy access clamp bar and automatic lamp de-energisation to allow quick and easy re-lamping. Standard Specification Features Type of Protection ATEX Classification Area Classification Certificate Coding Enclosure Reflector/Geartray Entry Termination Installation Control Gear Relamping Lampholder Burning Position Ingress Protection Electrical Supply Ex e mb q (Increased safety Encapsulation Powder filling) Group II Category 2 GD Zone 1 and 21 areas to EN and EN with installation to EN EC Type Examination Certificate Baseefa04ATEX0220 II 2 GD Ex e mb q IIC T4 Tamb 55 C GRP body with polycarbonate cover and brass suspension points White polyester painted zinc coated steel 4 x M20 cable entries, 2 at each end Quick release mains terminals - 3 core 4mm² max. conductor with looping and 16A rating through wiring. (6mm² terminations available - /SC option) Two M8 tapped brass inserts located on rear of body High Frequency Quick release diffuser clamp and hinged cover G13 (Bi-pin) Universal IP66/67 to EN V - 254V 50/60Hz, V dc Simple rugged construction Full length easy access diffuser clamp Advanced control gear gives 50/60Hz operation, high power correction factor and regulated lamp output that is 20% greater at -20 C than competitors Resistant to voltage fluctuations dc operation Automatic lamp de-energisation on opening Quick release mains terminals DTS-01 deluge tested Vibration tested to comply with Lloyds/DNV End of life (EOL) protection to IEC (with EOL I and EOL II functionality) International Approvals ATEX, GB (China), GOST, CSA and CEPEL IECEx Compliant

4 ATEX CATEGORY 2 ZONE 1 & 21 APPLICATIONS 23 Std. Cat No. Wattage Lamp TClass T C (Dust) Ambient C Weight PRGE/218/BI 2x18W T8 T to kg PRGE/236/BI 2x36W T8 T to kg PRGE/218/MO 2x18W T8 T to kg PRGE/236/MO 2x36W T8 T to kg MO - Mono-pin (Fa6 Cap) Lamps. Mono-pin Coding: Ex d e q. Options - Suffix to Catalogue No. /120 /M25 /SC /SB Specific voltage (110/130) M25 cable entries Screwed connection terminal block (up to 6mm² conductors) Stainless steel mounting bush /3P /LBE /EL /SE 3 phase termination facility (Not available if looping required) Looping both ends Extra live termination facility (to match emergency circuit) Spigot entry Accessories Should be ordered separately Pole mounting bracket assembly (38-42mm diameter poles) Pole mounting bracket assembly (48-52mm diameter poles) Pole mounting bracket assembly (58-62mm diameter poles) Hook type ceiling bracket assembly Ceiling mounting bracket assembly Eyebolt mounting assembly Flush mounting wall bracket assembly Looping kit (allows looping from both ends of luminaire) For details on outreach brackets see page 29. Catalogue Order Code SPOL SPOL SPOL SPRO SPRO SPRO SPRO SPROT-0021 Product design and specifications are subject to change without notice, please check the Chalmit website for latest specifications.

5 PROTECTA III E 24 Ex e EMERGENCY FLUORESCENT Utilising the same reliable design of the standard Protecta III, the emergency version also features intelligent battery and lamp management technology. The luminaire is capable of self commissioning and routine self-testing to ensure safe and dependable emergency operation. A high emergency output version is also available that increases the lumen output in emergency mode. Standard Specification Features Type of Protection ATEX Classification Area Classification Certificate Coding Enclosure Reflector/Geartray Entry Termination Installation Control Gear Relamping Lampholder Burning Position Ingress Protection Electrical Supply Battery Duration Emergency Output Ex e mb q (Increased safety Encapsulation Powder filling) Group II Category 2 GD Zone 1 and 21 areas to EN and EN with installation to EN EC Type Examination Certificate Baseefa04ATEX0220 II 2 GD Ex e mb q IIC T4 Tamb 55 C GRP body with polycarbonate cover and brass suspension points White polyester painted zinc coated steel 4 x M20 cable entries, 2 at each end Quick release mains terminals - 4 core 4mm² max. conductor with looping and 16A rating through wiring. (6mm² terminations available - /SC option) Two M8 tapped brass inserts located on rear of body High Frequency Quick release diffuser clamp and hinged cover G13 (Bi-pin) Universal IP66/67 to EN V - 254V 50/60Hz Internal Ni-Cd (6V) 90 minutes to EN % of one lamp (18W) 25% of one lamp (36W) Ability to detect and indicate impending end of emergency lamp life before actual failure Battery management, monitoring and automatic self test Emergency inhibition and mains power off re-start Automatic lamp de-energisation on opening DTS-01 deluge tested Vibration tested to comply with Lloyds/DNV End of life (EOL) protection to IEC (with EOL I and EOL II functionality) International Approvals ATEX, GB (China), GOST, CSA and CEPEL IECEx Compliant

6 ATEX CATEGORY 2 ZONE 1 & 21 APPLICATIONS 25 Std. Cat No. Wattage Lamp TClass T C (Dust) Ambient C Weight PRGE/218/BI/EM 2x18W T8 T to kg PRGE/236/BI/EM 2x36W T8 T to kg PRGE/218/MO/EM 2x18W T8 T to kg PRGE/236/MO/EM 2x36W T8 T to kg MO - Mono-pin (Fa6 Cap) Lamps. Mono-pin Coding: Ex d e mb q IIC. Options - Suffix to Catalogue No. /120 Specific voltage (110/130) /LBE Looping both ends /M25 M25 cable entries /HEO High emergency output - 45% (36W only) /SC /SB Screwed connection terminal block (up to 6mm² conductors) Stainless steel mounting bush /3H /RI 3 hour battery duration* Remote emergency inhibition facility (External switch ordered separately) /3P 3 phase termination facility (Not available if looping required) /SE Spigot entry * 18W = 30% of one lamp, 36W = 25% of one lamp Accessories Should be ordered separately Pole mounting bracket assembly (38-42mm diameter poles) Pole mounting bracket assembly (48-52mm diameter poles) Pole mounting bracket assembly (58-62mm diameter poles) Hook type ceiling bracket assembly Ceiling mounting bracket assembly Eyebolt mounting assembly Flush mounting wall bracket assembly Looping kit (allows looping from both ends of luminaire) Remote Ex switch for emergency inhibition (1 switch controls up to 10 luminaires) For details on outreach brackets see page 29. Catalogue Order Code SPOL SPOL SPOL SPRO SPRO SPRO SPRO SPROT-0021 SPROT-0033 Product design and specifications are subject to change without notice, please check the Chalmit website for latest specifications.

7 PROTECTA III S/S STAINLESS STEEL 26 Ex e FLUORESCENT The Protecta III is also available in a stainless steel body version. This incorporates the same design and monitoring features found in the GRP body Protecta. The increased durability of its stainless steel construction makes this luminaire ideal for applications where there is a high risk of mechanical damage or exposure to chemical agents. Standard Specification Features Type of Protection ATEX Classification Area Classification Certificate Coding Enclosure Reflector/Geartray Entry Termination Installation Lampholder Control Gear Relamping Burning Position Ingress Protection Electrical Supply Battery Duration Emergency Output Ex e mb q (Increased safety Encapsulation Powder filling) Group II Category 2 GD Zone 1 and Zone 21 areas to EN and EN with installation to EN EC Type Examination Certificate Baseefa04ATEX0220 II 2 GD Ex e mb q IIC T4 Tamb 55 C (45 C for emergency version) Marine grade 316S31 stainless steel body with polycarbonate cover White polyester painted zinc coated steel 4 x M20 cable entries, 2 at each end Quick release mains terminals - 3 core 4mm² max. conductor with looping and through wiring facility. 4 core 4mm² connectors on emergency). (6mm² terminations available - /SC option) Two M8 tapped stainless steel inserts located on rear of body G13 (Bi-pin) High Frequency Quick release diffuser clamps and hinged cover Universal IP66 to EN V - 254V 50/60Hz 220V - 300V dc (non-emergency only) Internal Ni-Cd (6V) 90 minutes to EN % of one lamp (18W) 25% of one lamp (36W) 316 Stainless steel body and clamp bar Advanced control gear gives 50/60Hz operation, high power correction factor and regulated lamp output that is 20% greater at -20 C Automatic lamp de-energisation on opening Resistance to voltage fluctuations Battery management, monitoring and automatic self test dc operation (non-emergency only) Ability to detect and indicate impending end of emergency lamp life before actual failure End of life (EOL) protection to IEC (with EOL I and EOL II functionality) International Approvals ATEX, GB (China), GOST, CSA and CEPEL IECEx Compliant

8 ATEX CATEGORY 2 ZONE 1 & 21 APPLICATIONS 27 Std. Cat No. Wattage Lamp TClass T C (Dust) Ambient C Weight PRSE/218/BI 2x18W T8 T to kg PRSE/236/BI 2x36W T8 T to kg PRSE/218/BI/EM 2x18W T8 T to kg PRSE/236/BI/EM 2x36W T8 T to kg PRSE/218/MO 2x18W T8 T to kg PRSE/236/MO 2x36W T8 T to kg PRSE/218/MO/EM 2x18W T8 T to kg PRSE/236/MO/EM 2x36W T8 T to kg MO - Mono-pin (Fa6 Cap) Lamps. Mono-pin Coding: Ex d e q. Mono-pin emergency coding: Ex d e mb q IIC. Options - Suffix to Catalogue No. /120 /M25 /SC /3P Specific voltage (110/130V) M25 cable entries Screwed connection terminal block (up to 6mm² conductors) 3 phase termination facility (Not available if looping required) /LBE /EL /HEO /3H Looping both ends Extra live termination facility (compatible with 4 core switched emergency circuits) High emergency output - 45% (36W only) 3 hour battery duration* * 18W = 30% of one lamp, 36W = 25% of one lamp Accessories Should be ordered separately Pole mounting bracket assembly (38-42mm diameter poles) Pole mounting bracket assembly (48-52mm diameter poles) Pole mounting bracket assembly (58-62mm diameter poles) Hook type ceiling bracket assembly Ceiling mounting bracket assembly Eyebolt mounting assembly Flush mounting wall bracket assembly Looping kit (allows looping from both ends of luminaire) Remote Ex switch for emergency inhibition (1 switch controls up to 10 luminaires) For details on outreach brackets see page 29. Catalogue Order Code SPOL SPOL SPOL SPRO SPRO SPRO SPRO SPROT-0021 SPROT-0033 Product design and specifications are subject to change without notice, please check the Chalmit website for latest specifications.

9 PROTECTA III 28 Pole Mounting Bracket Assembly Cat No. SPOL /100002/ Pole mounting bracket to suit pole diameter (38-42mm) SPOL (48-52mm) SPOL (58-62mm) SPOL Hook Type Ceiling Bracket Assembly Cat No. SPRO Ceiling Mounting Bracket Assembly Cat No. SPRO Eyelet Mounting Assembly Cat No. SPRO5-0005

10 MOUNTING OPTIONS 29 Flush Mounting Wall Bracket Assembly Cat No. SPRO Note: All brackets are made from 316 Stainless Steel Wall Mounting Outreach Bracket Cat No. NPRO4-0007/0008/0012 Pole length A for use with the following: 1. 18W and 36W spigot entry body, size A = 250mm Cat No. NPRO W body c/w pole clamps (SPOL ), size A = 650mm Cat No. NPRO W body c/w pole clamps, (SPOL ) size A = 1100mm Cat No. NPRO Pole clamps for items 2 & 3 must be ordered separately, see SPOL W Spigot Entry Cat No. PRGE/218/BI/SE 36W Spigot Entry Cat No. PRGE/236/BI/SE

11 PROTECTA n 68 NORMAL and EMERGENCY LIGHTING Ex n FLUORESCENT The Protecta n utilises the proven strength and integrity as the Protecta III but is certified for use in Zone 2, Zone 21 and Zone 22 hazardous areas. The luminaire is recommended for use in areas where high levels of ingress protection is required Standard Specification Features Type of Protection ATEX Classification Area Classification Certificate Coding Enclosure Reflector Entry Termination Installation Control Gear Relamping Burning Position Ingress Protection Electrical Supply Battery Duration Emergency Output Ex na (Non-sparking) Group II Category 3 GD Zone 2 and Zone 22 areas to EN and EN with installation to EN Type Examination Certificate Baseefa08ATEX0227 IEC Certificate IECExBAS II 3 GD Ex na Refer to table for T rating and Ambient GRP body with polycarbonate cover and brass suspension points White polyester painted zinc coated steel 4 x M20 cable entries, 2 at each end 3 core 4mm² max. conductor with looping and through wiring 16A rating. 4 core 4mm² connectors on emergency). (6mm² terminations available - /SC option) Two M8 tapped brass inserts located on rear of body. High Frequency electronic ballast Emergency - electronic/inverter Quick release diffuser clamp and hinged cover Universal IP66/67 to EN V 50/60Hz Ni-Cd 6V (Emergency version only) 3 hours (Emergency version only) 18W 32% of one lamp 36W 14% of one lamp Easy access to suspended control gear tray High frequency control gear gives 50/60Hz operation, high power factor correction and regulation of lamp output dc operation (non-emergency only) Vibration tested to comply with Lloyds/ DNV DTS-01 deluge tested End of life (EOL) protection to IEC (with EOL I and EOL II functionality) Suitable for Zone 21 (Dust) areas Type Examination Certificate Baseefa08ATEX0228 Coding II 2D Ex td A21 T85 C International Approvals ATEX IECEx Compliant

12 ATEX CATEGORY 3 ZONE 2, 21 & 22 APPLICATIONS 69 Std. Cat No. Wattage TClass(Gas) T C (Dust) Ambient C Weight PR2N/218/BI 2x18W T to kg PR2N/136/BI 1x36W T to kg PR2N/236/BI 2x36W T to kg PR2N/218/BI/EM 2x18W T to kg PR2N/136/BI/EM 1x36W T to kg PR2N/236/BI/EM 2x36W T to kg Options - Suffix to Catalogue No. /120 Specific voltage (110V-130V) /3P Three phase termination /SC /M25 Screwed connection terminal block (up to 6mm² conductors) M25 cable entries /MF /IS /SE Mains fuse Isolation switch Spigot entry Accessories Should be ordered separately Pole mounting bracket assembly (38-42mm diameter poles) Pole mounting bracket assembly (48-52mm diameter poles) Pole mounting bracket assembly (58-62mm diameter poles) Hook type ceiling bracket assembly Ceiling bracket assembly Flush mounting wall bracket assembly Eyebolt mounting assembly Looping Kit (allows looping from both ends of luminaire) 18W wall mounting outreach bracket (use with SPOL ) Catalogue Order Code SPOL SPOL SPOL SPRO SPRO SPRO SPRO SPROT-0021 NPRO W wall mounting outreach bracket (use with SPOL ) Product design and specifications are subject to change without notice, please check the Chalmit website for latest specifications. NPRO4-0012

13 PROTECTA 96 SURFACE MOUNTED FLUORESCENT The Protecta is a proven and reliable T8 fluorescent luminaire. The Protecta s rugged, corrosion resistant construction (IP66/IP67) combined with an advanced high frequency ballast ensure minimum product maintenance is required. When access is required the Protecta Industrial features an easy access clamp bar and automatic lamp de-energisation to allow quick and easy re-lamping. Standard Specification Features Ingress Protection Enclosure Entries Termination Reflector/Gear-tray Mounting Control Gear Relamping IP66/67 to EN60529 GRP body with clear polycarbonate diffuser and brass suspension points 4 x M20 cable entries (2 each end) Quick release mains terminals - 3 core 4mm² max. conductor with looping and 16A rating through wiring. (6mm² terminations available - /SC option) White polyester painted zinc coated steel Two M8 brass inserts on rear of body High frequency electronic control gear Via quick-release diffuser clamp and hinged diffuser Simple rugged construction Full length easy access diffuser clamp Hinged cover Standard fixing centres When fitted high frequency control gear gives 50/60Hz operation, high power factor correction and regulation of lamp output Quick release mains terminals DTS-01 deluge tested Vibration tested to comply with Lloyds/DNV A copper and iron version is also available. To order substitute /HF with /ES and specify the voltage Electrical Supply V 50/60Hz

14 INDUSTRIAL and MARINE APPLICATIONS 97 Std. Cat No. Wattage Lamp TClass Lampholder Weight PRGI/118/BI/HF 1x18W Fluorescent T8 G13 6kg PRGI/218/BI/HF 2x18W Fluorescent T8 G13 6.1kg PRGI/136/BI/HF 1x36W Fluorescent T8 G13 9.6kg PRGI/236/BI/HF 2x36W Fluorescent T8 G13 9.8kg Options - Suffix to Catalogue No. /--- Specific voltage - Copper/iron ballasts: 120, 220, 230, 254V /3P 3 phase termination facility (not available if looping is required) /ES Electronic start (copper/iron ballast only) /M25 M25 cable entry /60 /EL 60Hz supply (copper/iron ballasts only) Extra live termination (compatible with 4 core switched emergency models) /SC /SB Screwed connection terminal block (up to 6mm² conductors) Stainless steel mounting bush /MF Mains fuse /SE Spigot entry Accessories Should be ordered separately Pole mounting bracket assembly (38-42mm diameter poles) Pole mounting bracket assembly (48-52mm diameter poles) Pole mounting bracket assembly (58-62mm diameter poles) Hook type ceiling bracket assembly Ceiling bracket assembly Flush mounting wall bracket assembly Eyebolt mounting assembly Looping Kit (allows looping from both ends of luminaire) 18W wall mounting outreach bracket (use with SPOL ) Catalogue Order Code SPOL SPOL SPOL SPRO SPRO SPRO SPRO SPROT-0021 NPRO W wall mounting outreach bracket (use with SPOL ) Product design and specifications are subject to change without notice, please check the Chalmit website for latest specifications. NPRO4-0012

15 PROTECTA E 98 EMERGENCY FLUORESCENT The Protecta Industrial has the same rugged and proven design as the Ex Protecta. This includes high ingress protection with DTS-01 deluge compliance and vibration resistance in accordance with Lloyds/DNV standards. The Emergency version also features an internal battery to allow operation in the event of mains power failure. Standard Specification Features Ingress Protection Enclosure Entries Termination Reflector/Gear-tray Mounting Control Gear Relamping IP66/67 to EN60529 GRP body with clear polycarbonate diffuser and brass suspension points 4 x M20 cable entries (2 each end) Quick release mains terminals - 3 core 4mm² max. conductor with looping and 16A rating through wiring. (6mm² terminations available - /SC option) White polyester painted zinc coated steel Two M8 brass inserts on rear of body High frequency ballast & invertor c/w battery pack Via quick-release diffuser clamp and hinged diffuser Simple rugged construction Full length easy access diffuser clamp Standard fixing centres High frequency control gear gives 50/60Hz operation, high power factor correction and regulation of lamp output Quick release mains terminals DTS-01 deluge tested Vibration tested to comply with Lloyds/DNV Optional battery monitoring and self-testing control gear Electrical Supply V 50/60Hz Battery Ni-Cd (6V) Duration 3 Hours to EN Emergency Output 32% of one lamp (18W) 14% of one lamp (36W)

16 INDUSTRIAL and MARINE APPLICATIONS 99 Std. Cat No. Wattage Lamp TClass Lampholder Weight PRGI/118/BI/EM 1x18W Fluorescent T8 G13 8.1kg PRGI/218/BI/EM 2x18W Fluorescent T8 G13 8.3kg PRGI/136/BI/EM 1x36W Fluorescent T8 G kg PRGI/236/BI/EM 2x36W Fluorescent T8 G kg Options - Suffix to Catalogue No. /120 /NM /MF /3P V Non-maintained (single lamp models only) Mains fuse 3 phase termination facility (not available if through wiring is required) /SC /SB /LBE /BMT Screwed connection terminal block (up to 6mm² conductors) Stainless steel mounting bush Looping both ends Battery monitoring and self-test /M25 M25 cable entry /SE Spigot entry Accessories Should be ordered separately Pole mounting bracket assembly (38-42mm diameter poles) Pole mounting bracket assembly (48-52mm diameter poles) Pole mounting bracket assembly (58-62mm diameter poles) Hook type ceiling bracket assembly Ceiling bracket assembly Flush mounting wall bracket assembly Eyebolt mounting assembly Looping Kit (allows looping from both ends of luminaire) 18W wall mounting outreach bracket (use with SPOL ) Catalogue Order Code SPOL SPOL SPOL SPRO SPRO SPRO SPRO SPROT-0021 NPRO W wall mounting outreach bracket (use with SPOL ) Product design and specifications are subject to change without notice, please check the Chalmit website for latest specifications. NPRO4-0012

17 PROTECTA S/S 100 STAINLESS STEEL FLUORESCENT The Protecta is also available in a stainless steel body version. This incorporates the same design and monitoring features found in the GRP body Protecta. The increased durability of its stainless steel construction makes this luminaire ideal for applications where there is a high risk of mechanical damage or exposure to chemical agents. Standard Specification Features Ingress Protection Enclosure Entries Termination Installation Reflector/Gear-tray Control Gear Relamping Electrical Supply IP66/67 to EN60529 Marine grade 316S31 stainless steel body with clear polycarbonate diffuser 4 x M20 cable entries (2 each end) Quick release mains terminals - 3 core 4mm² max. conductor with looping and 16A rating through wiring. (6mm² terminations available - /SC option) Two M8 tapped stainless steel inserts located on rear of body White polyester painted zinc coated steel High frequency electronic control gear Via quick-release diffuser clamp and hinged diffuser V 50/60Hz Emergency version 220/254V 50/60Hz Simple rugged construction Hinged cover with easily removeable cover clamps Standard fixing centres High frequency control gear gives 50/60Hz operation, high power factor correction and regulation of lamp output Quick release mains terminals Resistance to voltage fluctuations Optional battery monitoring and self-testing control gear A non-emergency copper and iron version is also available. To order substitute /HF with /ES and specify the voltage Battery Ni-Cd (6V) Duration 3 Hours Emergency Output 32% of one lamp (18W) 14% of one lamp (36W)

18 INDUSTRIAL and MARINE APPLICATIONS 101 Std. Cat No. Wattage Lamp TClass Lampholder Weight PRSI/118/BI/HF 1x18W Fluorescent T8 G13 5.9kg PRSI/218/BI/HF 2x18W Fluorescent T8 G13 6.2kg PRSI/136/BI/HF 1x36W Fluorescent T8 G13 9.6kg PRSI/236/BI/HF 2x36W Fluorescent T8 G kg PRSI/118/BI/EM 1x18W Fluorescent T8 G13 8.7kg PRSI/218/BI/EM 2x18W Fluorescent T8 G13 9.0kg PRSI/136/BI/EM 1x36W Fluorescent T8 G kg PRSI/236/BI/EM 2x36W Fluorescent T8 G kg Options - Suffix to Catalogue No. /120 /ES /--- /60 /EL V High frequency ballast (for /EM Emergency models only) Electronic start (copper/iron ballast only) Specific voltage (120*, 220, 230 & 254V only available copper/iron gear) 60Hz supply (copper/iron ballasts only) Extra live termination (Compatible with four core switched emergency models) * 120V copper/iron gear - non emergency only /M25 /SC /MF /3P /LBE /BMT M25 cable entries Screwed connection terminal block (up to 6mm² conductors) Mains fuse 3 phase termination facility Looping both ends Battery monitoring and self-test Accessories Should be ordered separately Catalogue Order Code Pole mounting bracket assembly (38-42mm diameter poles) SPOL Pole mounting bracket assembly (48-52mm diameter poles) SPOL Pole mounting bracket assembly (58-62mm diameter poles) SPOL Hook type ceiling bracket assembly SPRO Ceiling bracket assembly SPRO Flush mounting wall bracket assembly SPRO Eyebolt mounting assembly SPRO Looping Kit (allows looping from both ends of luminaire) SPROT W wall mounting outreach bracket (use with SPOL ) NPRO W wall mounting outreach bracket (use with SPOL ) NPRO Product design and specifications are subject to change without notice, please check the Chalmit website for latest specifications.