QUICK START INSTALLATION GUIDE ANALOG - INTELLIGENT POWER CENTER (IPC)
|
|
- Juniper Holt
- 5 years ago
- Views:
Transcription
1 Intelligent LED Lighting Systems TM QUICK START INSTALLATION GUIDE ANALOG - INTELLIGENT POWER CENTER (IPC) LIGHTS & POWER: (Note all lights fixtures to be wired in series) 1) Identify dry, non-plenum location for IPC. Determine location & orientation of IPC and Break-Out Modules. Note: Vertical orientation of IPC is best for cooling. Make sure Analog zone inputs are visible and accessible. See page 6 of IPC specifications for optional acceptable orientations. 2) Run wires from the Break-Out Module locations directly to the fixture locations. 3) Mount IPC to board w/ #8 screws or self-tapping screws or in an approved enclosure. Use approved plenum enclosure if unit is located in plenum. 4) With typical 115Vac input, IPC consumes 2.7 amps. Standard 15 amp breaker can accommodate up to 4 IPCs and a 20 amp breaker can accommodate up to 5 IPCs. If wiring only 4 or 5 IPCs, consider powering from two separate circuits for redundancy. Note: 115Vac = 2.7 Amps, 240 Vac = 1.1 A & 227 Vac = 1.0 A. 5) Provide service disconnect switch for IPCs if not in close proximity to electrical panel or as required per code. 6) Provide line-voltage power to IPC and wire as specified on page 7 of IPC installation manual. (Black to Line, White to Neutral & Green to Ground.) 7) Select Master control or up to 4 zones of analog control. See Analog switch option diagrams. 8) Wire class 2 IPC wires to Break-Out Modules. See Detail B4.09, B4.12, B6.09 or B6.12. (Black is always Negative.) 9) Wire fixture home runs to the Break-Out Modules. See Detail B4.09, B4.12, B6.09 or B6.12. (Black is always Negative.) 10) Wire fixtures in series. Wire only two fixtures per channel, typ. See Detail A1 for wiring fixtures in series. 11) If not using Master zone control, track which fixtures are on which zones on a plan or chart. Note: For complete and more technical installation instructions refer to the LumaStream Intelligent Power Center Application and Installation Manual included with each unit. Rev LumaStream.com nd Avenue N, Suite D, St. Petersburg, FL
2 18/2 MULTICONDUCTOR CABLE LED LED LED LED LED LED ZONE4 LED LED LED LED LED LED ZONE3 LED LED LED LED LED LED ZONE2 B6 BREAKOUT MODULE B3 BREAKOUT MODULE B3 BREAKOUT MODULE LED LED LED LED LED LED ZONE1 24 LED FIXTURES Low voltage toggle switches and/or 0-10V analog dimmers VIOLET VIOLET AC MAINS GRAY GRAY GRAY GRAY GROUND (GREEN) NEUT (WHITE) LINE (BLACK) ZONE 1 ZONE 2 ZONE 3 ZONE 4 Note: For the UP position to be ON, toggle switches must be installed upside down. When switch is closed, LED s are OFF. TITLE: DWG #: INDEPENDENT ZONE CONTROL USING SWITCHES AND/OR 0-10V DIMMERS WIR-ANA-001 REV: B
3
4 VIOLET GRAY 0-10V dimmer Leviton # IP710-DLZ Hunt # PS-LED-010 LINE (BLACK) AC MAINS GROUND (GREEN) NEUT (WHITE) LINE (BLACK) TITLE: DWG #: MASTER ZONE CONTROL USING 0-10V DIMMER & ON/OFF SWITCH WIR-ANA-002 REV: B
5 VIOLET GRAY VIOLET GRAY 1 Common WAY LOW VOLTAGE TOGGLE SWITCH 2 Travelers (Brass Screws) 2 LOW VOLTAGE TOGGLE SWITCH OR 0-10V DIMMER 2 ZONE 1&2 TITLE: DWG #: MULTIPLE ZONE CONTROL USING TOGGLE SWITCH OR 0-10V DIMMER WIR-ANA-003 REV: B
6 TRINITY #1 TRINITY #2 TRINITY #3 ETC. VIOLET GRAY LOW VOLTAGE TOGGLE SWITCH AND/OR 0-10V DIMMER TITLE: MULTIPLE TRINITY MASTER CONTROL USING TOGGLE SWITCH AND/OR 0-10V DIMMER DWG #: WIR-ANA-004 REV: B
7 4 Inch Recessed New Construction LED Luminaire Installation Instructions OWNER/USER RESPONSIBILITIES: It is the responsibility of the contractor, installer, buyer, owner and user to install, maintain and operate this luminaire in accordance with all applicable laws, building codes, regulations and local Electrical Safety Authority requirements. This product is only to be installed by a qualified person. WARNING Shut OFF power at fuse box or circuit breaker before installation. Turn power OFF before inspection or removal of LED light source. Installation: 1. Pull on LED Trim Ring in direction shown to remove LED light source from housing. Flip open one lever on each Wire Lever Nut to disconnect wires. 2. Extend bar hangers to fit between joists. Bar hanger foot aligns with bottom of joist. Hammer pre-installed nails into joists. When installing in drywall, cut 4-1/2 hole. If necessary, adjust fixture for ceiling thickness by loosening hex screws then retighten. 3. Remove Junction Box cover. Remove appropriate knock-out and insert strain relief (not supplied) into hole. Flip open Wire Lever Nut. Connect Class 2 constant current source: Connect +Ve to RED. Connect Ve to BLACK, by inserting stripped wire into Wire Lever Nut. Close lever. OBSERVE CORRECT POLARITY. Failure to do so will damage LED light source. Replace Junction Box cover. 4. Re-connect LED light source to housing. Connect RED to RED, BLACK to BLACK. OBSERVE CORRECT POLARITY. Failure to do so will damage LED light source. Compress Flat Spring Clips with fingers and insert into housing opening. Press upwards until trim ring is flush against the ceiling. LumaStream, Inc nd Ave. N Saint Petersburg, FL T: Page 1 of 1 Disclaimer: LumaStream Inc. reserves the right to make changes without further notice to any products herein to improve reliability, function, or design. LumaStream does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. info@lumastream.com LumaStream, Inc. All Rights Reserved Doc No: 4.0 RI Installation Revision: Feb
8 4 Inch Recessed Re-Model LED Luminaire Installation Instructions OWNER/USER RESPONSIBILITIES: It is the responsibility of the contractor, installer, buyer, owner and user to install, maintain and operate this luminaire in accordance with all applicable laws, building codes, regulations and local Electrical Safety Authority requirements. This product is only to be installed by a qualified person. WARNING Shut OFF power at fuse box or circuit breaker before installation. Turn power OFF before inspection or removal of LED light source. Installation: 1. Pull on LED Trim Ring in direction shown to remove LED light source from housing. Flip open one lever on each Wire Lever Nut to disconnect wires. 2. Cut 4-3/8 hole in ceiling. Pull Class 2 wiring through hole in ceiling. Remove Junction Box cover. Remove appropriate knock-out and insert strain relief (not supplied) into hole. Flip open Wire Lever Nut. Connect Class 2 constant current source: Connect +Ve to RED. Connect Ve to BLACK, by inserting stripped wire into Wire Lever Nut. Close lever. OBSERVE CORRECT POLARITY. Failure to do so will damage LED light source. Replace Junction Box cover. 3. Pass junction box up into hole in ceiling. Retract clips into housing and insert housing into ceiling. Press clips outwards to hold housing in place. To remove from ceiling, pull clips down and back into housing 4. Re-connect LED light source to housing. Connect RED to RED, BLACK to BLACK. OBSERVE CORRECT POLARITY. Failure to do so will damage LED light source. Compress Flat Spring Clips with fingers and insert into housing opening. Press upwards until trim ring is flush against the ceiling. LumaStream, Inc nd Ave. N Saint Petersburg, FL T: Page 1 of 1 Disclaimer: LumaStream Inc. reserves the right to make changes without further notice to any products herein to improve reliability, function, or design. LumaStream does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights, nor the rights of others. info@lumastream.com LumaStream, Inc. All Rights Reserved Doc No: 4.0 RC Installation Revision: Feb
MEDIA LED. Pendant Standard Mount Installation ou de montage WARNING:
MEDIA LED Pendant Standard Mount WARNING: Disconnect main power at the source prior to installation! Thread gripper base onto 1 /4 20 stud, or with #8 screw. Depress gripper nozzle to insert aircraft cable.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS This document explains mounting for pendant, recessed, and wall PENDANT - STEP ONE INSTALL MOUNTING POINTS Non-power feed mounting points may be positioned 1 to 12 or 12 to 18
More informationEMERY SKY SUSPENDED LED LUMINAIRE
EMERY SKY SUSPENDED LED LUMINAIRE IP20 DRY LOCATION 120V- 277V AC SAFETY & WARNINGS 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS 2. Install in accordance with national and local electrical code regulations.
More informationECO-T LED RECESSED TROFFER USER MANUAL
ECO-T LED RECESSED TROFFER USER MANUAL INSTALLATION GUIDE FOR: 2X2: MLRT22D4535 MLRT22D4541 MLRT22D4550 2X4: MLRT24D5535 MLRT24D5541 MLRT24D5550 Thank you for purchasing this MaxLite product. For additional
More informationMaxLite StaxMax LED Flood Lights
Operating Instructions MaxLite StaxMax LED Flood Lights Input Rating 120V-277V 50/60Hz (347/480v optional) Wet Location Rated IP65 Operating temperature -22⁰F to 105⁰F General Safety Information 1. READ
More informationINSTALLATION INSTRUCTION Oculux 3.5" Architectural Downlight R3CRN-11, R3CSN-11
. INSTALLATION INSTRUCTION SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified
More informationLIGHTPLANE 1 RECESSED - LP1R
INSTRUCTIONS LIGHTPLANE 1 RECESSED - LP1R Safety & Warnings! When installing or using this recessed fixture basic safety precautions should be followed: 1. Read ALL INSTRUCTIONS before installing 2. This
More informationDMR 3005 WM ONE ZONE WIRELESS DIMMER RECEIVER
E363518 DMR 3005 WM ONE ZONE WIRELESS DIMMER RECEIVER 20725 NE. 16 AVE. #A-33 MIAMI, FLORIDA 33179 Tel: (305) 652-2599 Fax: (305) 650-8812 www.lumiron.com Email: sales@lumiron.com 1 Benefits and Features
More informationINSTALLATION INSTRUCTION Aether 3.5 Color Tunable LED Downlight
SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS!
IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. When using electrical equipment, basic safety precautions should always be followed including the following: DISCONNECT AC POWER SUPPLY BEFORE
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationLED Garage Light INSTALLATION INSTRUCTIONS. *Model number noted on carton label
LED Garage Light *Model number noted on carton label INSTALLATION INSTRUCTIONS Model Number / Número de Modelo / Numéro des modèle SGLL 24 PIR (24 LED Garage Light) Actual Dimensions 10 W x 3-1/2 H x 24-1/2
More informationPatient Care Facility Multiple Room Configuration Style 3 W/ Ver 4.41 pcb & Pulse Relay pcb(s)
ISIMET DLA Controller Patient Care Facility Multiple Room Configuration Style 3 W/ Ver 4.41 pcb & Pulse Relay pcb(s) Installation, Operations, Start-up and Maintenance Instructions Application: The DLA
More informationZIP LIGHT LED LUMINAIRE
LED LUMINAIRE INSTALLATION MANUAL Note: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the Canadian Electrical Code (CE) and for the United States follow
More informationRound or Square Chicago Plenum Hi-lume Wall Wash Housing with LED Lamp for Flanged Trims E3_F_-L_WC-HL 1.0
Installation Instructions for 90ELED-WHL-FL Round or Square Chicago Plenum Hi-lume Wall Wash Housing with LED Lamp for Flanged Trims E_F_-L_WC-HL.0 LED - ROUND/SQUARE FLANGED GENERAL PRODUCT I NFORMATION:
More informationCFP-LED Contractor Select Flat Panel. Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions
More informationInstallation Instructions MX LED Enhanced Color Adjustable
Installation Instructions 1 of 5 MX Enhanced Color Adjustable Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly.
More informationPatient Care Facility
ISIMET Patient Care Facility DLA Controller Individual Room Configuration Style 1 W/ Ver 4.41 pcb & Pulse Relay pcb Installation, Operations, Start-up and Maintenance Instructions Meets all Standards for
More informationDrug Testing Labs. Style 2 W/ Ver 4.41 pcb & Pulse Relay pcb(s) Installation, Operations, Start-up and Maintenance Instructions
ISIMET Drug Testing Labs DLA Controller Style 2 W/ Ver 4.41 pcb & Pulse Relay pcb(s) Installation, Operations, Start-up and Maintenance Instructions Meets all Standards for Canadian Industrial Control
More informationJandy Pro Series WaterColors LED Lights Underwater Large and Small Light
installation Manual English Jandy Pro Series WaterColors LED Lights Underwater Large and Small Light FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified
More informationInstallation Instructions 4 Gravity Enhanced Color Adjustable
Installation Instructions 1 of 5 Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly. Follow installation
More informationINSTALLATION INSTRUCTION W Track Suspension system
SAFETY INSTRUCTIONS: - Suspension mounting system should be installed by a qualified electrician only. - System is intended for installation in accordance with National Electric Code, local and - Federal
More informationTrack Accessories. Single Circuit Track. L Connector T Connector X Connector. Mini Connector Floating Canopy End Feed Kit.
Single Circuit Single Circuit Track Live End Connector Flexible Connector Straight Connector Track supplied with dead end and mounting hardware Live end connector used for direct wiring Flexible connector
More informationIvalo Finiré 3 LED Recessed Lighting Installation Instructions
IMPORTANT INFORMATION Please Read Before Installing 367-2578e 1 09.20.16 Important Notes IC fixtures must be used for installations containing insulating materials and must be mounted away from heat producing
More informationINSTALLATION INSTRUCTION Aether 2 Shallow Recessed Housing
SAFETY INSTRUCTIONS IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance
More informationInstallation Instructions: Eco Linear High Bay
Installation Instructions: Eco Linear High Bay Installation Notes & Precautions: Read all precautions, warnings, instructions contained in this document. These instructions can be used to install Eco Linear
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
07 Edge Lighting. All Rights Reserved. Installation Instructions for Pix Stick Tie Stix Suspension -Light, -Light, -Light and -Light with Power IMPORTANT INFORMATION - This product is suitable for indoor
More informationStrip Fixture URS Light Bar Retrofit Installation Instructions Revised:
Strip Fixture URS Light Bar Retrofit Installation Instructions Revised: 20180126 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency
More informationFW-IOB-T-120/208VAC Input/Output/Bypass Assembly. Installation Instructions
FW-IOB-T-120/208VAC Input/Output/Bypass Assembly Installation Instructions The OutBack Power Systems FW-IOB-T-120/208VAC allows manual switching between the FX Series Inverter/ Charger and a second AC
More informationPatient Care Facility
ISIMET Patient Care Facility DLA Controller Individual Room Configuration Style 1 W/ Ver 4.41 pcb & Pulse Relay pcb Installation, Operations, Start-up and Maintenance Instructions Meets all Standards for
More informationPower In - Pathways Technology Wall
Power In - Pathways Technology Wall NOTE: With an off module application involving the transition of cabling or electrical harnesses, you will have to drill a maximum of a 2-1/2" hole in the beltway trim
More informationDrug Testing Labs. Style 2 W/ Ver 4.41 pcb & Pulse Relay pcb(s) Installation, Operations, Start-up and Maintenance Instructions
ISIMET Drug Testing Labs DLA Controller Style 2 W/ Ver 4.41 pcb & Pulse Relay pcb(s) Installation, Operations, Start-up and Maintenance Instructions Meets all Standards for Canadian Industrial Control
More informationInstallation Instructions & Users Manual IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Crystal Recessed Edge- lit LED Exit Signs Series CRRBB & CRRAC Battery Backup & AC Models 01.18.06 Installation Instructions & Users Manual IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
More informationTwo Circuit Trac System TRAC SECTION, JOINERS & FEEDS
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low profile, two-circuit trac sections for surface or pendant mounting. Provides two separate 20-amp circuits from a single
More informationPRODUCT MANUAL Gecko Wireless One Zone LED Dimmer and Receiver
Product Description The Gecko Wireless One Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location
More informationHigh Bay Luminaire Series
High Bay Luminaire Series INSTALLATION INSTRUCTIONS The High Bay Luminaire is ideal for installations with mounting heights over 25 feet. The fixture can be mounted with a hook or pendant with flexible
More informationInstallation, Maintenance and Service Manual Power Cord
Installation, Maintenance and Service Manual Power Cord 45-081, REV. 8/14 1 of 8 Table Of Contents Section 1 Installation Procedure... 3 1.1 General...3 1.2 Sheave installation...4 1.3 Anchor installation...4
More informationCutler-Hammer. Installation Instructions for the ND OPTIM 550 PowerNet and/or Zone Interlock Accessories (ICK 550N, ZGK550N, ZGPK550N) I.L.
Cutler-Hammer Installation Instructions for the ND OPTIM 550 PowerNet and/or Zone Interlock Accessories (ICK 550N, ZGK550N, ZGPK550N)! WARNING CONTACT WITH ENERGIZED EQUIPMENT CAN RESULT IN DEATH, SEVERE
More informationOne Circuit Trac System TRAC SECTION, JOINERS & FEEDS T Series
Project: Fixture Type: Location: Contact/Phone: PRODUCT DESCRIPTION DIMENSIONS Low-Profile, single-circuit trac sections for surface or pendant mounting. I-beam cross section provides added strength and
More informationSection One: Install the Constant Current DMX Driver
Intelligent LED Driver/Controller Output 060VDC, 0050mA, 0W SELV equivalent : 0% typ. in in out out Group Group LEDcode in in out out Group Group LEDcode 06 Edge Lighting. All Rights Reserved. Installation
More informationHBC-20 - LED HIGH BAY
To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA.) in Canada. Risk of fire or
More informationOutdoor Installation Using an Electronic LED Power Supply (TE-60L-12)
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 606 Tel: 77-770-9 Fax: 77-9-6 www.edgelighting.com info@edgelighting.com Installation Instructions for Port Round & Square LED PORT-RD-ST-SA
More informationOperation/Installation Instructions
Important Information These instructions contain safety information, read and follow them carefully. Dialight will not accept any responsibility for injury, damage or loss which may occur due to incorrect
More informationAUTO CHARGE 12 DV AUTOMATIC BATTERY CHARGER
File: 091-165-12-DV_revD.PDF Rev: D, Date: 02-25-16 INSTRUCTION MANUAL AUTO CHARGE 12 DV AUTOMATIC BATTERY CHARGER MODEL #091-165-12-DV INPUT: 115 or 230VAC, 50/60Hz OUTPUT: 13.2VDC (nom.), 12 Amperes
More informationRated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications
WPC1-XXXX-T Rated for use on 110/120VAC 60Hz and 220/240VAC 60Hz applications Installation Instructions: Read these instructions in their entirety before performing any installation work. FOR USE WITH
More informationALL700/ALL700-CM INSTALLATION INSTRUCTIONS
ALL700/ALL700-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More informationUse and Care Guide. Part # UC SV-D Model # UC SV-d UC SV-d
Part # UC-12-5-930-SV-D Model # 53502111 UC-18-9-930-SV-d 53503111 UC-24-12-930-SV-d 53504111 Use and Care Guide BEM DJUSTBLE LED UNDER CBINET LIGHT WITH MGN MOUNT INSTLLTION OPTION Questions, problems,
More informationCIRRUS SUSPENSION WITH RECTANGULAR 1 LENS WITH REMOTE POWER, END FEED
Diffused Rectangular 1 Lens Description Cirrus R1 Suspension with Remote Power is a linear LED fixture that offers direct light in a clean, contemporary style. Cirrus R1 is available in various increments
More informationCIRRUS CEILING WALL WASH WITH REMOTE POWER
0.9" 0.9" CIRRUS CEILING WALL WASH (ACTUAL SIZE) CIRRUS CEILING WALL WASH LENS (ACTUAL SIZE) DESCRIPTION At 7.3 or 9.6 watts per foot, Cirrus Channel Wall Wash contains 85+ or 95+ CRI LEDs. Fixture mounts
More informationTRAILER AUXILIARY POWER SYSTEM (TAPS) INSTALLATION GUIDE V1.10
TRAILER AUXILIARY POWER SYSTEM (TAPS) INSTALLATION GUIDE V1.10 TAPS INSTALLATION GUIDE V1.10 1 TRAILER AUXILIARY POWER SYSTEM CONTENTS General Information and System Logic... 2 Diagrams... 3 System Diagram
More informationSTRATO LED Drivers 70W, Single output
Features STRATO switch mode driver technology is designed to generate one constant current output from a wide range AC input. The size and performance of these products make them the ideal choice for LED
More informationPRODUCT MANUAL Gecko Wireless 2 Zone LED Dimmer and Receiver
Product Description The Gecko Wireless 2 Zone Wall LED Dimmer has been designed to bring light control easily. No wires or switch box locations are needed, just stick or mount the Gecko to any flat location
More informationModel LA 4300 Time Delay OFF Controller
ISIMET LA Series Model LA 4300 Time Delay OFF Controller Installation, Operation and Maintenance Manual Application: The Time Delay OFF Controller operates as a single output controller where the application
More informationDual-Feed 200A 4/5 TPA/GMT Fuse Alarm Panel. Model Installation Guide
Dual-Feed 200A 4/5 TPA/GMT Fuse Alarm Panel Model 009-8005-0404 Installation Guide Dual-Feed 200A 4/5 TPA/GMT Fuse Alarm Panel Model 009-8005-0404 Installation Guide, Part number 123518-6 Copyright 2010,
More informationTraining Bulletin New Model Introduction
GE Monogram GE Consumer Service Training Training Bulletin New Model Introduction October 2001/ TB-14-01 ZV950SDSS Wall-Mount Euro-Style High Performance Vent Hood Purpose To introduce the new wall-mount
More informationALL200RM/ALL200RM-CM
ALL200RM/ALL200RM-CM INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power
More informationCIRRUS SUSPENSION WALL WASH WITH REMOTE POWER, END FEED
Adjustable Max. 5 ft. Description Cirrus Suspension Wall Wash with Remote 24VDC power supply (sold separately) is a linear LED fixture that offers a wall wash lens for a smooth and uniform beam spread.
More informationCIRRUS CEILING SQUARE 1 WITH REMOTE POWER
Diffused Square 1 (Actual Size) Description Cirrus Ceiling S1 is a linear LED fixture that offers direct light in a clean, contemporary style. Cirrus is available in various increments from 12" to 720"
More informationInstallation Instructions: External-Driver SEP T8 LED Tube Lamp
Installation Instructions: External-Driver SEP T8 LED Tube Lamp Installation Notes & Precautions: External-Driver SEP T8 LED Tube Lamp Read all precautions, warnings, instructions contained in this document.
More informationLED Downlight Ceiling Fixtures
ED Downlight Ceiling Fixtures Every attempt has been made to ensure that this documentation is as accurate and up-to-date as possible. However, Vertical Express assumes no liability for consequences, directly
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationMAINFRAME HOT RUNNER TEMPERATURE CONTROL SYSTEMS. Instruction Manual
MAINFRAME HOT RUNNER TEMPERATURE CONTROL SYSTEMS Instruction Manual Copyright, Athena Controls, Inc., 2006 Printed in USA CompuStep is a registered trademark of Athena Controls, Inc. SafeChange is a trademark
More informationModel LA 4100 Time Delay OFF Controller
ISIMET LA Series Model LA 4100 Time Delay OFF Controller Installation, Operation and Maintenance Manual Application: The Time Delay OFF Controller operates as a single output controller where the application
More informationProject. Comments. Prepared by
DESCRIPTION Recessed 6-inch ED lens downlight is available in various distributions, lumen and CRI/CCT options. Suitable for commercial construction and can be used for both new or renovation work. Insulation
More informationMXG2DSTL 3.5 MX G2 LED Square Trimless Downlight
MXG2DSTL 3.5 MX G2 LED Square Trimless Downlight ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt 1 1/2 L0 L1 L2 L3 10W 16W 20W 26W * System Wattage includes
More informationReveal, 24VDC Plaster-In LED system
Drywall 3.75" (9.5cm) 2.88" (7.3cm) 6" (15.2cm) Description: Reveal, a 24VDC linear LD system features a shallow, plaster-in aluminum extrusion no thicker than drywall. The system May be secured directly
More informationAsymmetrical Installation Instructions. Components: i2cove Asymmetrical LED Light Fixtures. 12 [305mm] [918mm] 48.
support@i2systems.com www.i2systems.com Electrical Specifications PARAMETER Input Power VALUE 8 Watts* / Ft Input Voltage 120-277V AC, 50/60 Hz Max. Fixture Run Length LED Color (CCT) 8 Watts: 120VAC:
More informationSURFACE/CEILING & SUSPENDED MOUNT INSTALLATION
SURFE/CEILING & SUSPENDED MOUNT INSTALLATION E477827 E477827 APPLICATION NL luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, corrosion, vibration and rough
More informationOptimax Pro Retrofit Instructions
Copyright 2011 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in examples herein are fictitious unless otherwise noted. No part
More informationAlbeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series)
GE Lighting Installation Guide Albeo TM LED Luminaire Heavy Industrial High Bay Lighting (ABR1-Series) Features UL 1598 Suitable for Wet Locations IP66 Rated Ingress Protection BEFORE YOU BEGIN Read these
More informationUltra-Thin Recessed LED Light Installation Guide
TM PROFESSIONAL GRADE LED LIGHTING www.aspectled.com Copyright 2012-2016. aspectled, Inc. 1 OVERVIEW aspectled s Ultra-Thin series of recessed lights are bright, energy efficient, attractively styled,
More informationHIGHBAY RAIL 400W INSTALLATION INSTRUCTIONS
TM INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical Code and
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from
More informationOperating Instructions
CIDII & CIIDI Rated LED High Bay / Flood Light Luminaire Important Information: These instructions contain safety information; read and follow them carefully. Dialight will not accept any responsibility
More informationAUTO CHARGE LPC SERIES
INSTRUCTION MANUAL FILE: IM_091-206-12_revB REV: B REVISED BY: THN DATE: 09-17-2012 AUTO CHARGE LPC SERIES MODEL #091-206-12 LPC STANDARD DISPLAY INPUT: 115 volt, 50/60 Hz, 13 amps OUTPUT: 80 AMPERES 3
More informationLED Utility Wrap Fixture
Operating Instruction Please read and save these instructions. Read through this owner s manual carefully before using product. Protect yourself and others by observing all safety information, warnings,
More informationINSTRUCTION SHEET. Installation Instructions for Mercmaster LED Luminaire. Applications. Agency Ratings. Product Safety
650457-000 INSTRUCTION SHEET Installation Instructions for Mercmaster Luminaire for proper and safe installation of this product, please read the following instructions. Applications Marine and wet locations;
More informationLumination TM LED Luminaire LUR Series
Installation Guide Lumination TM LED Luminaire LUR Series BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF FIRE OR ELECTRIC SHOCK Turn power off before inspection,
More informationLED Flat Panel Installation Instructions For 1 x4, 2 x2, and 2 x4 LED Flat Panels (FP Series)
LED Flat Panel Installation Instructions For 1 x4, 2 x2, and 2 x4 LED Flat Panels (FP Series) PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION SAFETY
More information1.4 N/1.4 D. Operating Instructions. 580 Mayer Street, Building #7, Bridgeville, PA phone fax
1.4 N/1.4 D Operating Instructions 580 Mayer Street, Building #7, Bridgeville, PA 15017 phone 412.206.0106 fax 412.206.0146 www.brightlines.com 2006 Brightline, L.P. Safety Warning: Do not dim a non-dim
More informationINSTALLATION MANUAL. Melink Corporation (513) Revision
INSTALLATION MANUAL Revision 130711 Table of Contents Step Installation Contractor Page 1 Install System Controller Electrical 4 2 Install Variable Frequency Drive Electrical 6 3 Install Touchpad Mechanical
More informationSno Konette. Instruction Manual Deluxe Model #1002EX Standard Model #1003EX DC Battery Model #1009EX. Cincinnati, OH USA.
Sno Konette Instruction Manual Deluxe Model #1002EX Standard Model #1003EX DC Battery Model #1009EX Part No. 22045EX Revised June 1996 Model #1002EX Model #1003EX Cincinnati, OH 45241-4807 USA SAFETY PRECAUTIONS
More informationLED IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage from fire, electric shock, falling
More informationLAD8R - Remodel 8 LED Architectural Downlight
Catalog # : Project : Prepared By : Date : LAD8R - Remodel 8 inch Remodel LED downlight delivers superior performance and energy efficiency. Designed to use anodized aluminum reflectors delivering even
More informationALL W INSTALLATION INSTRUCTIONS
ALL1000-3300W INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power source
More informationZ22C-** Preconfigured Network Zone System
Z22C-** Preconfigured Network Zone System Page 1 of 12 TABLE OF CONTENTS Overview of Products Specs / Tools Needed Safety Information / Warnings Wall Mounting Bracket Installation Wall Mounting Removable
More informationInstallation Instructions MX LED Downlight Remodel
1 of 5 Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. Luminaire will fail if not installed properly. Follow installation instructions. Risk
More informationMAXLITE RKT LED Retrofit Kit
MAXLITE RKT LED Retrofit Kit Description and Intended Use The RKT LED Retrofit Kit is a high performance LED Fixture upgrade kit designed to replace the original components inside 2 x2 and 2 x4 fluorescent
More informationUniversal Retrofit System Installation Instructions Revised:
Universal Retrofit System Installation Instructions Revised: 20150624 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency to
More informationModel LA 4400 Time Delay OFF Controller
ISIMET LA Series Model LA 4400 Time Delay OFF Controller Installation, Operation and Maintenance Manual Application: The Time Delay OFF Controller with integral 24-hr. programmable time clock operates
More informationCatalog # Project. Comments. Prepared by
Halo LE ICAT Housing for New Construction Recessed 6 sloped ceiling LE ICAT housing for ceilings from 2/12 to 12/12 pitch. The socket aiming mechanism tilts the lamp straight down regardless of ceiling
More informationGEM INC. OF CAPRI. Radio Remote Lift Controls
GEM INC. OF CAPRI Radio Remote Lift Controls GEM INC OF CAPRI Owners Manual GEM Inc. 356 Capri Blvd. Phone 941.642.0873/5366 Fax 941.642.8391 Table of Contents CHAPTER 1 Installation Manual 1 CHAPTER 2
More informationInstallation Instructions: Memory-Dimmable SEP T8 Tube Lamps
Installation Instructions: Memory-Dimmable SEP T8 Tube Lamps Installation Notes & Precautions: Memory-Dimmable SEP T8 LED Tube Lamp Read all precautions, warnings, instructions contained in this document.
More information29048, 29049, 29050, 29051, 29052, 20953, 29054,
July 15, 2008 Lit. No. 29225, Rev. 06 29048, 29049, 29050, 29051, 29052, 20953, 29054, 29400-2 HARNESS KIT 3-PORT ISOLATION MODULE LIGHT SYSTEM w/2-plug SYSTEM HARNESSES Installation Instructions Read
More informationService Guide JATCO Environmental Protection Tank Model J-7000
Service Guide JATCO Environmental Protection Tank Model J-7000 Listed below are a series of steps to follow if the JATCO tank fails to dump properly. #1. Be sure there is an adequate supply of gas pressure
More informationMXG2DSTR 3.5 MX G2 LED Square Downlight Wood Ceiling
MXG2DSTR 3.5 MX G2 LED Square Downlight Wood Ceiling ELECTRICAL DATA Available finishes LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 L3 10W 16W 20W 26W 750lm
More informationINSPECTOR LINE LOAD SIMULATOR INSTRUCTION MANUAL TASCO, INC.
INSPECTOR LINE LOAD SIMULATOR INSTRUCTION MANUAL INS120P TASCO, INC. THIS TESTER IS DESIGNED FOR USE ONLY BY QUALIFIED ELECTRICIANS. IMPORTANT SAFETY WARNINGS mwarning Read and understand this material
More informationPOWER INVERTER 1,000 WATT / 2,000 WATT PEAK
POWER INVERTER 1,000 WATT / 2,000 WATT PEAK 94009 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOUS
More informationMXG2DSTR 3.5 MX G2 LED Square Downlight
MXG2DSTR 3.5 MX G2 LED Square Downlight ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 L3 10W 16W 20W 26W * System Wattage includes driver and
More information