Installation Instructions MX LED Downlight Remodel
|
|
- Corey Gray
- 6 years ago
- Views:
Transcription
1 1 of 5 Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. Luminaire will fail if not installed properly. Follow installation instructions. Risk of injury. Wear safety glasses and gloves during installation and servicing. Allow ample time to cool before handling. IMPORTANT SAFETY INSTRUCTIONS Read all installation instructions before installing. It is important to save these instructions. Only install and connect LED module with power disconnected at the circuit breaker. Hot plugging, or connecting the module with power on, could damage the LEDs and is not covered by warranty. Connectors on modules and approved housings are keyed for specific voltage combinations; do not force or attempt to bypass connectors. Observe and follow all label information and instructions regarding dry, damp and wet location listings, proper Intense LED module, warnings of installation near combustible materials and/or insulation. Turn off power at circuit breaker before attempting to install or perform maintenance on the fixtures. Be sure to connect ground wire to prevent electric shock or other potential hazards. The product must be installed in a manner consistent with the intended use and in compliance with the national electrical codes and local codes by a person familiar with the construction and operation of the product and the hazards involved. Do not block the trim aperture as this may cause unsafe operating conditions. WARNING: RISK OF FIRE. Non-IC fixture requires that insulation must be kept at least 3 away from all sides of the fixture. Minimum of 90 C supply conductors. Consult a qualified electrician before installation. WARNING: Use only Intense Lighting trims listed for use with this fixture. Use of trims other than those listed by Intense Lighting is a violation of N.E.C 110-3(B) and voids all warranties. CEILING CUT OUT: 1. Cut out ceiling hole according to size: -- Round: 4 1/8 (105mm) diameter -- Square: 4 1/16 x 4 1/16 (103mm x 103mm) Note: Oversized holes will not allow fixture and/or trim to fit correctly. 1 REMOVE COVER PLATE: 1. Remove (2) M3 pan head screws and junction box cover plate. 2. Remove knockout on cover plate and attach conduit or Romex cable /8 [105mm] 4 1/16 [103mm] Cover Plate M3 x 5mm pan head ELECTRICAL CONNECTIONS: 3 1. Connect ground from fixture to green (GROUND) supply wire, black wire from fixture to black (HOT) supply wire and white wire from fixture to white (NEUTRAL) supply wire. Use UL listed connectors or wire nuts to make the connections (provided by others). Connect dimming wires if applicable, see page Replace cover plate and (2) M3 pan head screws. INSTALL HOUSING: 1. Make sure swing out lugs are in a closed position. 2. Insert driver housing through ceiling opening. 3. Rest the driver housing in the ceiling plenum. 4. Push remodel assembly into ceiling opening. 4 LED Module Ceiling opening Black Red Hot Neutral Ground 120V / 277V connection wires Driver housing Swing out lugs Junction box INSTRUCTIONS L/M P-1
2 2 of 5 REMODEL ASSEMBLY INSTALLATION: 5 Use a #1 screwdriver to tighten the (3) swing out lugs into open position (Do not overtighten). Note: Ceiling thickness must be between 5/16 [8mm] and 3/4 [19mm]. MODULE INSTALLATION: 1. Check that power is off at breaker, hot plugging may damage LEDs. 2. Connect female quick connect from housing to male quick connect on module. 3. Snap module into channel and confirm module sits parallel to ceiling line and is securely fastened into housing. 6 (3) M3 x 25mm Quick connect Channel Swing out lug ADJUSTING HORIZONTAL ADJUSTMENT: 1. Loosen fastener with a #1 screwdriver to allow fixture to adjust 359º horizontally. 2. Place screwdriver in adjustment assist to rotate module to desired horizontal position. 3. Tighten fastener to lock horizontal adjustment. 7 TRIM INSTALLATION: 1. Position trim alignment label to trim location tab in the fixture. 2. Snap trim into fixture. 8 Trim location tab M3 x 6mm fastener Trim alignment label INSTRUCTIONS L/M P-2
3 3 of 5 ACCESSORY HOLDER: 1. Rotate release cap by turning counter clockwise. 2. Install accessories into accessory holder and replace accessory holder s retaining clip. 3. Place accessory holder and accessory flush against optic and replace release cap. OPTIC REPLACEMENT: 1. Remove trim, then remove module from channel and disconnect quick connect. 2. Rotate release cap by turning counter clockwise. 3. Set cap and retainer ring aside and change optics. 4. Align optic pins to slots in module. Module Module Accessories Accessory holder s retaining clip Accessory holder Optic Retainer ring Optic slots Release cap Release cap REPLACEMENT: 1. Adjust vertical angle to 0º and remove module from channel and disconnect quick connect. 2. Unscrew all three swing out lugs with a #1 screwdriver. Make sure the swing lugs are in the closed position. 3. Remove the remodel assembly and the driver housing will follow. 4. Remove cover plate and slide out driver bracket. 5. Replace new driver on driver bracket and replace module quick connect Driver Driver Bracket 5 Driver Housing Module Quick Connect 3 Cover Plate M3 x 5mm pan head 8/32 nuts INSTRUCTIONS L/M P-3
4 Accessories and Options 4 of 5 LED MODULE KIT Example: MXMG2L02712 SERIES WATTAGE CCT / CRI OPTIC MXMG2 (MX G2 Module) L0 (10 Watts) L1 (16 Watts) L2 (20 Watts) L3 (26 Watts) 27 (2700K / 82 CRI) 279 (2700K / 92 CRI) 30 (3000K / 82 CRI) 309 (3000K / 92 CRI) 35 (3500K / 82 CRI) 359 (3500K / 92 CRI) 41 (4100K / 82 CRI) 419 (4100K / 92 CRI) CA35 (Class A 3500K) CW30 (CrispWhite 3000K) 12 (12º Spot) 24 (24º Narrow Flood) 36 (36º Flood) 50 (50º Wide Flood) LED OPTICS Example: IP-OP4724 IP-OP4712 (12º Spot) IP-OP4724 (24º Narrow Flood) IP-OP4736 (36º Flood) IP-OP4750 (50º Wide Flood) ACCESSORY HOLDER Holds two filter media LH47 (Accessory Holder, Black) FILTER MEDIA Requires an accessory holder PFLMB-47 (Hex Louver, Black) PFL4-47 (Solite Lens) PFL2-47 (Linear Spread Lens) PFL1-47 (Prismatic Spread Lens) WET LOCATION KIT Converts downlight trims into wet location trims. SERIES LENS TYPE MXL-RD (Round Downlight) MXL-SD (Square Downlight) MXL-RP (Round Pinhole) MXL-SP (Square Pinhole) -SL (Solite) -CR (Clear Tempered) -FR (Frosted) INSTRUCTIONS L/M P-4
5 Dimming Compatibility 5 of V DIMMING (10% Dimming, eldoled 1%, eldoled 0.1%) --120V/277V and power packs Manufacturer Part Number(s) HUNT PS-010-IV-120V, PS-010-WH-120V, PS-010-3W-IV-120, PS-010-3W-WH-120V, PS-010-IV-277V, PS-010-WH-277V, PS-010-3W-IV-277V, PS-010-3W-WH-277V, FD-010: PS-IFC-010-IV, PS-IFC-010-WH-120/277V, FD-010: PS-IFC-010-3W-IV, PS-IFC-010-3W-WH-120/277V, FD V, FD V Leviton Leviton Centura Fluorescent Control System, IllumaTech IP7 Series, DPSPE-212 Lightolier ZP600FAM120, MP1500FAM120, V2000FAMU Lithonia LEQ BC, LEQ LVBC, SLD LVBC, SQ1DC Lutron DVTV, NTFTV Synergy ISD BC 120/277 INPUT 0-10V DIMMER VIOLET (+) GREY (-) LUTRON ECOSYSTEM DIMMING --120V or 277V --Dims down to 1% or 5% Product Part Number(s) EcoSystem CS-1L-WM, CS-2L-WM, CS-1L-CM, CS-2L-CM, EcoSystem ESN, Grafik Eye QS with EcoSystem, Quantum ECO SYSTEM CONTROL (BY OTHERS) ECO SYS BUS VIOLET (E1) VIOLET (E2) LUTRON HI-LUME DIMMING --120V or 277V --Dims down to 1% Product Part Number(s) NovaT NTF-10, NTF-103P, NTF-103P-277, NTF Nova NF-10, NF-103P, NF-103P-277, NF Vareo VF-10 Skylark SF-10P, SF-12P-277, SF-12P-277-3, SF-103P Diva DVF-103, DVF-103P-277, DVSCF-103P, DVSCF-103P-277 Ariadni AYF-103P, AYF-103P-277 Vierti VTF-6AM Maestro MAF-6AM, MAF-6AM-277, MSCF-6AM, MCSF-6AM-277 Maestro Wireless MRF2-F6AN-DV Spacer System SPSF-6A, SPSF-6A-277, SPSF-6AM, SPSF-6AM-277 Lyneo LXF-103PL, LXF-103PL-277 Radio RA 2 RRD-F6AN-DV HomeWorks QS HQRD-F6AN-DV 3-WIRE CONTROL (BY OTHERS) ORANGE ELV DIMMING --120V only --Dims down to 1% MX MODULE DIMS DOWN TO Product Part Number(s) L0 (10W) L1 (16W) L2 (20W) L3 (26W) Leviton IPI06-1LZ - 1% 1% 1% Leviton 6633-P 1% 1% 1% - Lutron DVCL-153P 1% 1% 1% 1% Lutron S600P 3% 1% 2% 2% Cooper DLC03P - 1% 1% 2% Cooper DAL06P - 1% 1% 1% 120V INPUT FROM DIMMER INSTRUCTIONS L/M P-5
MXG2PRD 3.5 MX G2 LED Downlight Pendant
MXG2PRD 3.5 MX G2 LED Downlight Pendant ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 10W 16W 20W 3000K / 82 CRI 3000K / 82 CRI 3000K / 82 CRI
More informationIHOLC4DR 4 Gravity LED Downlight Cylinder
IHOLC4DR 4 Gravity LED Downlight Cylinder ELECTRICAL DATA LED Light Engine Delivered Lumens * System Wattage ** M1 M2 L1 L2 L3 900lm @ 3000K / 82 CRI 1800lm @ 3000K / 82 CRI 2500lm @ 3000K / 82 CRI 3400lm
More informationMXG2DRTR 3.5 MX G2 LED Wood Ceiling Lensed Pinhole - Wet Location
MXG2DRTR 3.5 MX G2 LED Wood Ceiling Lensed Pinhole - Wet Location ELECTRICAL DATA Available finishes LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 L3 10W 16W
More informationMXG2DRTR 3.5 MX G2 LED Lensed Pinhole - Wet Location
MXG2DRTR 3.5 MX G2 LED Lensed Pinhole - Wet Location ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 L3 10W 16W 20W 26W * System Wattage includes
More informationMXG2DSTR 3.5 MX G2 LED Square Downlight
MXG2DSTR 3.5 MX G2 LED Square Downlight ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 L3 10W 16W 20W 26W * System Wattage includes driver and
More informationMXG2DRTR 3.5 MX G2 LED Downlight
MXG2DRTR 3.5 MX G2 LED Downlight ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 L3 10W 16W 20W 26W * System Wattage includes driver and LED Module
More informationMXG2DSTL 3.5 MX G2 LED Square Trimless Downlight
MXG2DSTL 3.5 MX G2 LED Square Trimless Downlight ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt 1 1/2 L0 L1 L2 L3 10W 16W 20W 26W * System Wattage includes
More informationMXG2DSTL 3.5 MX G2 LED Square Trimless Lensed Downlight - Wet Location
MXG2DSTL 3.5 MX G2 LED Square Trimless Lensed Downlight - Wet Location ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt 1 1/2 L0 L1 L2 L3 10W 16W 20W 26W
More informationMXG2DRTR 3.5 MX G2 LED Lensed Downlight - Wet Location
MXG2DRTR 3.5 MX G2 LED Lensed Downlight - Wet Location ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 L3 10W 16W 20W 26W * System Wattage includes
More informationMXG2DSTR 3.5 MX G2 LED Square Downlight Wood Ceiling
MXG2DSTR 3.5 MX G2 LED Square Downlight Wood Ceiling ELECTRICAL DATA Available finishes LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** Lumens Per Watt L0 L1 L2 L3 10W 16W 20W 26W 750lm
More informationInstallation Instructions MX LED Enhanced Color Adjustable
Installation Instructions 1 of 5 MX Enhanced Color Adjustable Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly.
More information3 1 4" x 3 1 4" 4 1 2" x 4 1 2" HEATSINK: Proprietary high performance aluminum die cast heatsink for maximum LED life.
Beve Trimless Downlight PRODUCT INNOVATION AWARDS 211 PLATINUM WINNER MOST UNIQUE PRODUCT WINNER 331 1" Regress LUMINAIRE INFORMATION APPLICATION: Accent luminaire for Residential, Commercial, Retail or
More informationL4B-F-RF Round Fixed Frame In BRO
DESIGNED & ASSEMBLED IN CANADA L4B-F-RF Round Fixed Frame In BRO The L4B-F series is designed for non insulated ceilings. A 20 Ga. Black powder coated steel baseplate is designed for bidirectional mounting
More informationMXS Matrix Small BRO
DESIGNED & ASSEMBLED IN CANADA MXS Matrix Small BRO The Matrix family of recessed multiples throws powerful illumination to direct occupant focus. To aid in setting the scene, each lamp head rests in a
More informationInstallation Instructions 4 Gravity Enhanced Color Adjustable
Installation Instructions 1 of 5 Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly. Follow installation
More informationD4B-F-R 3 Series Round Frame In BRO
DESIGNED & ASSEMBLED IN CANADA D4B-F-R 3 Series Round Frame In BRO The D4B-F-R series is designed for non insulated ceilings. A unique design allows installation of very shallow plenums as low as 5" (when
More informationSS6G2 / IC630 6 Architectural LED Round Generation 2 / Open Reflector
SSG2 / I3 rchitectural LED Round Generation 2 / Open JO NME TLOG NUMER DEORTIVE 7 /2 7 5/ 2 3/4 ut-out: /2 3 /2 Order Matrix Example: SSG2238-27-EM SSG2 5 2 3 D E 278 38 358 48 LED Recessed Round Module
More informationMXS Trimless Matrix Small XTM
MXS Trimless Matrix Small XTM FEATURES A DETAILS Trim Class: 4" Category: Recessed Trimless Multiple Shape: Rectangle Adjustability: Aiming WIth Rotation MXS-Trimless-Matrix-Small-XTM-Specs Subject to
More informationClassic Frame & DRD2X Apex Series Recessed LED Downlight Commercial Remodel 6", 8" Aperture
PRODUCT SPECIFICATIONS Frame-in Kit MOUNTING FRAME: Die-formed sheet metal. JUNCTION BOX: Galvanized steel. Equipped with (4) /2" and (2) 3 /4" knockouts with pryout slots to allow straight conduit runs.
More informationOneFrame & DRD2 Recessed LED Downlight General New Construction DRDHNJD Deep Junction Box
PRODUCT SPECIFICATIONS Frame-in Kit JUNCTION BOX: Metallic outlet box certified UL514A up to 2 hour fire rating. DRDHNJD equipped with (8) trade size knockouts (four concentric side ( 3 /4" + 1 /2"), two
More informationOneFrame & DRD2X Apex Series Recessed LED Downlight General New Construction DRDHNJD Deep Junction Box
PRODUCT SPECIFICATIONS Sound rated, architectural recessed LED downlight, 120/277V High performance Apex Series DRD2 Architectural-grade illumination produces up to 4000 candelas of focused light Precise,
More informationOneFrame & DRD2 Recessed LED Downlight General New Construction DRDHNJD Deep Junction Box
PRODUCT SPECIFICATIONS Sound rated, architectural recessed LED downlight, 120/277V Twist & Lock feature for easy trim installation 750 & 1000 lumen outputs, powered by Cree 93+ CRI LEDs 2700K, 3000K, 3500K,
More informationOneFrame & DRD4 Adjustable Recessed LED Downlight Concrete Tight New Construction DRDHNJC Deep Junction Box
PRODUCT SPECIFICATIONS Frame-in Kit JUNCTION BOX: Metallic outlet box certified UL514A up to 2 hour fire rating. Equipped with (4) trade size concentric knockouts ( 3 /4 + 1 /2 ) to allow straight conduit
More informationDRD2 Recessed LED Downlight Commercial New Construction 4", 6", 8" Aperture
PRODUCT SPECIFICATIONS Frame-in Kit MOUNTING FRAME: Die-cast aluminum. JUNCTION BOX: Galvanized steel. Equipped with (4) /2" and (2) 3 /4" knockouts with pryout slots to allow straight conduit runs. Approved
More informationDCCX Apex Series Commercial LED Cylinder Surface, Cord, Stem, Wall Mount
PRODUCT SPECIFICATIONS Apex Series DCCX delivers vivid, accurate light in the form of a completely customizable cylinder Powered by the high-performance DRD2X module for a precise, targeted beam of low
More informationDCCX. Apex Series LED Cylinder JA8. Surface, Cord, Stem, Wall Mount. Product Code: Spec Sheet V
Project: Product Code: Type: Date: Spec Sheet V- 08.20.8 Apex Series DCCX delivers vivid, accurate light in the form of a completely customizable cylinder Powered by the high-performance DRD2X module for
More informationAperture. Color Quality. 90+ CRI, 2-step SDCM. 2700K 3000K 3500K 4000K Spot (20 ) Narrow Flood (30 ) Flood (40 ) 4000cd (Spot 750 lm) Dimming
Project: Product Code: Type: Date: Spec Sheet V- 10.31.18 With multiple ratings, OneFrame is compliant in a wide range of situations Thanks to a unique low profile and small aperture design, OneFrame can
More informationOneFrame & DRD2 Recessed LED Downlight Concrete Tight New Construction DRDHNJC Deep Junction Box
PRODUCT SPECIFICATIONS Frame-in Kit JUNCTION BOX: Equipped with (4) trade size concentric knockouts ( 3 /4 + 1 /2 ) to allow straight conduit runs. Approved for 8 (four in, four out) #12 AWG C. MOUNTING:
More informationDRD3 Adjustable Recessed LED Downlight General New Construction 4, 5, 6 Aperture
PRODUCT SPECIFICATIONS 360 directional aim with up to 40 adjustable tilt Maximum installation compatibility Twist & Lock feature for easy trim installation 750 & 000 lumen outputs 2700K, 3000K, 3500K,
More informationDCCX. Apex Series LED Cylinder JA8. Surface, Cord, Stem, Wall Mount
Project: Product Code: Type: Date: Spec Sheet V- 2.0.8 Apex Series delivers vivid, accurate light in the form of a completely customizable cylinder Powered by the high-performance DRD2X module for a precise,
More informationFahrenheit DRD3 Adjustable LED Downlight Fire and Sound-Rated New Construction 4, 5, 6 Aperture
PRODUCT SPECIFICATIONS Frame-in Kit HOUSING: Fire and sound-rated housing. Up to 20 minute fire rated L500 (floor-ceiling) & P500 (roof-ceiling) design. Die formed #24 gauge galvanized steel construction.
More informationPROJECT INFORMATION DELIVERED PERFORMANCE. 14 Watts 20 Watts DOWNLIGHT. Performance based on 3000K. DELIVERED PERFORMANCE (Projected)
Beve mini Covered By US Patents 8,684,570 and 9,671,091 PROJECT INFORMATION PROJECT DATE TYPE 2221 DOWNLIGHT Beve mini Recessed Downlight - Good things come in small packages. Beve mini is the smallest
More informationDRD2 Recessed LED Downlight General Remodel 4", 5", 6" Aperture
PRODUCT SPECIFICATIONS Frame-in Kit HOUSING: Die-formed steel with powder coat finish (4" frame-in kit, 4" shallow frame-in kit), 20 ga. die-formed aluminum (5" frame-in kit), 22 ga. die-formed aluminum
More informationMOUNTING: Swing out lugs permit from below mounting into ceiling up to 1 1/2 (38 mm) thick LABELING: Approved to UL standards as tested by CSA
MULTIPLE RECESSED REMODELER 3 LIGHT 3LT APPLICATION: Accent and display lighting for retail, commercial and supermarket environments CONSTRUCTION: Steel driver housing Steel upper housing and laser cut
More informationDRD2X & OneFrame Concrete Apex Series Recessed LED Downlight
DRD2X & OneFrame Concrete Project: Product Code: Type: Date: Spec Sheet V- 10.31.18 Designed for high rise structures that require steel and concrete for reinforcement Features spot-welded areas and adaptations
More informationDRD5S Surface Mount LED Downlight General Retrofit Junction Box
PRODUCT SPECIFICATIONS Light Engine LED: Optimized LED array delivers smooth, uniform illumination with no visible fasteners or dark spots. LUMEN OUTPUT (POWER): 750 Im (9.0W), 1000 lm (12.0W). SHAPE:
More informationDCC2 LED Cylinder Surface, Cord, Stem, Wall Mount
PRODUCT SPECIFICATIONS Surface, Cord, Stem or Wall mounting options Available in White, Black, Bronze, Brushed Aluminum or Custom Color finishes Decorative frosted trim available 750, 000, 500 or 2000
More informationICL-LEDG2-2 MB G2 Recessed Multiple (2) Head - Gen 2
I-EG2-2 MB G2 Recessed Multiple (2) Head - Gen 2 JOB ATAOG EETRIA ATA E ight Engine attage 1 T / RI Nominal elivered umens 2, 3 1 2 3 4 10 14 20 29 1 System attage includes driver and E Module consumption
More informationMXG2SRTR1 MX G2 Semi Recessed Multiple (1) Head with New Construction Frame-In
MXG2SRTR1 MX G2 Semi Recessed Multiple (1) Head with New onstruction Frame-In ATAOG EETRIA ATA E ight Engine System attage * T / RI elivered umens ** umens Per att 0 1 2 10 16 20 / 82 RI / 82 RI / 82 RI
More informationDRD5S & SurfaceFrame. Surface Mount LED Downlight JA8. New Construction. DRDHNJO Octagonal Junction Box
New Construction Project: Product Code: Type: Date: Spec Sheet V- 11.15.18 Features multiple ratings to meet the demands of a wide range of situations Ultra-low profile allows it to install in as little
More informationMOUNTING: Swing out lugs permit from below mounting into ceiling up to 1 1/2 (38 mm) thick LABELING: Approved to UL standards as tested by CSA
2LT APPLICATION: Accent and display lighting for retail, commercial and supermarket environments CONSTRUCTION: Steel driver housing Steel upper housing and laser cut trim ring Complete die-cast optical
More informationDCC2. LED Cylinder JA8. Surface, Cord, Stem, Wall Mount
Project: Product Code: Type: Date: Spec Sheet V- 2.0.8 The cylinder s combination of precise illumination and refined aesthetics can take your designs to new heights Available in a range of form factors,
More informationDRD5S. Surface Mount LED Downlight JA8. Retrofit Junction Box
Project: Product Code: Type: Date: Spec Sheet V- 11.15.18 Thinnest-in-class delivers the pure, smooth light and the elegant look of a high-end recessed downlight Extends just 0.6 inches below the ceiling
More informationDRDHNJ Recessed LED Downlight General New Construction Junction Box
PRODUCT SPECIFICATIONS Frame-in Kit JUNCTION BOX: Metallic outlet box certified UL514A up to 2 hour fire rating. Equipped with (4) 1 /2 trade size knockouts (two side, two top) to allow straight conduit
More informationTrack Light. LIFETIME: 50,000 hours at 70% lumen maintenance. PHOTOMETRIC TESTING: Tested in accordance to IESNA LM
PRODUCT SPECIFICATIONS Track Light LED: Tightly binned, high performing white Cree LED. LUMEN OUTPUT (POWER): 900 lm (16.6W). CRI: 90+. CCT: 2700K, 3000K, 3500K, 4000K. BINNING: Color variation within
More informationDRD2 Recessed LED Downlight Commercial New Construction 4, 6, 8 Aperture
PRODUCT SPECIFICATIONS Frame-in Kit MOUNTING FRAME: Die-cast aluminum. JUNCTION BOX: Galvanized steel. Equipped with (4) 1 /2 and (2) 3 /4 knockouts with pryout slots to allow straight conduit runs. Approved
More informationDRD2 Recessed LED Downlight General New Construction Junction Box PRODUCT SPECIFICATIONS
PRODUCT SPECIFICATIONS Frame-in Kit JUNCTION BOX: Metallic outlet box certified UL514A up to 2 hour fire rating. Equipped with (4) 1 /2" trade size knockouts (two side, two top) to allow straight conduit
More informationDCD2 Recessed LED Downlight Commercial New Construction 4", 6", 8" Aperture
PRODUCT SPECIFICATIONS Frame-in Kit MOUNTING FRAME: Die-cast aluminum. JUNCTION BOX: Galvanized steel. Equipped with (4) /2" and (2) 3 /4" knockouts with pryout slots to allow straight conduit runs. Approved
More informationDRD2 & SurfaceFrame. Shallow Recessed LED Downlight JA8. New Construction. DRDHNJO Octagonal Junction Box
Project: Product Code: Type: Date: Spec Sheet V- 11.15.18 Features multiple ratings to meet the demands of a wide range of situations Ultra-low profile allows it to install in as little as 2" of ceiling
More informationDRD1 Surface Mount or Recessed LED Downlight General New Construction 4, 5, 6 Aperture
PRODUCT SPECIFICATIONS All-in-one LED luminaire for retrofit, remodel, and new construction Slim, drawn aluminum construction Easy, tool-less installation for 4, 5 or 6 recessed housings 750 lumens of
More informationDCC2 LED Cylinder Surface, Cord, Stem, Wall Mount
PRODUCT SPECIFICATIONS Luminaire LED: Tightly binned, high performing white Cree LED. LUMEN OUTPUT (POWER): 750 Im (.8W), 000 lm (4.7W), 500 lm (9.5W), 2000 lm (29.0W), 2 x 750 lm (23.6W), 2 x 000 lm (29.4W),
More informationCylindrix III Mini. Pendant Multiples
Cylindrix III Mini Pendant Multiples 2 Light Pendant Straight Multiple Product Overview Features Cylindrix III Mini Pendant Multiples perform beautifully, punching through higher ambient light with strong
More information40º 14 1 / Plaster Frame 6. Plaster Skim Coat (by others) ORDERING INFORMATION:
RECESSED TRIMLESS MULTIPLE 3 LIGHT 3LT APPLICATION: Accent and display lighting for retail, commercial and hospitality environments CONSTRUCTION: Stamped steel mounting frame w/integral mounting bars Steel
More informationDRD2 Recessed LED Downlight General Retrofit Junction Box
PRODUCT SPECIFICATIONS Light Engine LED: Tightly binned, high performing white Cree LED. LUMEN OUTPUT (POWER): 750 Im (10.8W), 1000 lm (12.8W). COLOR QUALITY: 93+ CRI, 2-step SDCM. CCT OPTIONS: 2700K,
More informationHornet HP. Pendant Multiples
2 Light Pendant Straight Multiple Features Hornet High Power (HP) perform beautifully, punching through higher ambient light with strong output making them perfect for retail applications. Designed for
More informationCIRRUS SUSPENSION WALL WASH WITH REMOTE POWER, END FEED
Adjustable Max. 5 ft. Description Cirrus Suspension Wall Wash with Remote 24VDC power supply (sold separately) is a linear LED fixture that offers a wall wash lens for a smooth and uniform beam spread.
More informationDCD1 Recessed LED Downlight Commercial New Construction 4, 6, 8 Aperture
PRODUCT SPECIFICATIONS Frame-in Kit MOUNTING FRAME: Die-cast aluminum. JUNCTION BOX: Galvanized steel. Equipped with (4) 1 /2 and (2) 3 /4 knockouts with pryout slots to allow straight conduit runs. Approved
More information1 1 / 4 13 / 16 45º ORDERING INFORMATION: 0-10V v dimming CP - Chicago plenum EM** - emergency battery pack (1 head)
SEMI-RECESSED TRIMLESS MULTIPLE 3 LIGHT 3LT APPLICATION: Accent and display lighting for retail, commercial and hospitality environments CONSTRUCTION: Stamped steel mounting frame with integral mounting
More informationIHOL-6DS / ISD602 6 Gravity LED Square Lensed Downlight - Wet Location
IHOL-6DS / ISD602 6 Gravity LED Square Lensed Downlight - Wet Location ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** M1 M2 L1 L2 L3 L4 L5 12W 25W 34W 46W 59W 75W 93W *
More informationCylindrix III Mini. Pendant Multiples
Cylindrix III Mini Pendant Multiples 2 Light Pendant Straight Multiple Product Overview Features Cylindrix III Mini Pendant Multiples perform beautifully, punching through higher ambient light with strong
More informationCylindrix III. Recessed Multiples
Features Cylindrix III Recessed LED, the best combination of optical and thermal performance, aesthetics and visual comfort in an recessed accent. Features a deeply recessed single LED light source for
More informationDCC2 LED Cylinder Surface, Cord, Stem, Wall Mount
PRODUCT SPECIFICATIONS Luminaire LED: Tightly binned, high performing white Cree LED. LUMEN OUTPUT (POWER): 750 Im (.8W), 000 lm (4.7W), 500 lm (9.5W), 2000 lm (29.0W), 750 / 750 lm (.8W /.8W), 000 / 000
More informationCylindrix III. Recessed Multiples
Features Cylindrix III Recessed LED, the best combination of optical and thermal performance, aesthetics and visual comfort in an recessed accent. Features a deeply recessed single LED light source for
More informationCylindrix III Mini. Pendant Multiples
Cylindrix III Mini Pendant Multiples 2 Light Pendant Straight Multiple 3 Light Pendant Straight Multiple Product Overview Performance Chart Features Cylindrix III Mini Pendant Multiples perform beautifully,
More informationNOVA suspension up and down, end feed with remote power supply
Shown without Louver Shown with White Louver Description Nova Suspension Up/Down is a linear LED lighting 2 circuit system that features both direct and indirect light. This contemporary system allows
More informationHornet HP. Pendant Multiples
2 Light Pendant Straight Multiple 3 Light Pendant Straight Multiple Features Hornet High Power (HP) perform beautifully, punching through higher ambient light with strong output making them perfect for
More informationHornet HP. Pendant/Surface Multiples
2 Light Pendant Straight Multiple 3 Light Pendant Straight Multiple Availability: 6/30/17 Features Hornet High Power (HP) perform beautifully, punching through higher ambient light with strong output making
More informationDCC2 LED Cylinder Surface, Cord, Stem, Wall Mount
PRODUCT SPECIFICATIONS Luminaire LED: Tightly binned, high performing white Cree LEDs enable excellent fixture to fixture color consistency and long lifetime. Delivers 93+ CRI in all available color temperatures.
More informationNanoLED NXT Cylinder LNRP3 Pendant
Nano NXT Cylinder LNRP3 Pendant NANO PENDANT - NANO PENDANT - 6 WITH CONDUIT CUTOUT NANO GLOW usailighting.com/cylinders Power and beauty are both in play with our sleek architectural cylinders. Concealing
More informationArchitectural grade at an affordable price. 3 DOWNLIGHTS NDLED RABWEB.COM
Architectural grade at an affordable price. NDLED DOWNLIGHTS RABWEB.COM 888-722-1000 3-in-1 housing. One-of-a-kind downlight. The NDLED housing delivers innovative design flexibility. Now you can install
More informationPROJECT INFORMATION PROJECT
SURFACE PROJECT INFORMATION PROJECT SURFACE DATE TYPE NanoLED Cylinder - Available in 2 wattage/lumen packages with maximum delivered lumens of over 1100 at 20W (57LPW). The NanoLED cylinder provides maximum
More informationCIRRUS SUSPENSION WITH RECTANGULAR 1 LENS WITH REMOTE POWER, END FEED
Diffused Rectangular 1 Lens Description Cirrus R1 Suspension with Remote Power is a linear LED fixture that offers direct light in a clean, contemporary style. Cirrus R1 is available in various increments
More informationRemote Power Supplies * & Dimmers (Sold Separately): Electronic Low Voltage Dimming (ELV) 0-10 Volt Dimming (0-10V) Lutron
0.25" (0.64cm) Grip Jack Connector Field Adjustable with Grip Jack Connector Adjustable Max. 5 ft. 0.9" 0.35" (0.9cm) 0.9" 0.38" (0.95cm) Description: Cirrus Channel Suspension Wall Wash uses a wall wash
More information0.25" (0.64cm) Grip Jack Connector 2WDC WDC Lumen values are based on the 3000K LED test.
0.25" (0.64cm) Grip Jack Connector Field Adjustable with Grip Jack Connector Adjustable Max. 5 ft. Description: Cirrus Channel Suspension D1 features a direct flat lens with 100 degree beam spread. At
More informationEssenza. Round Downlights
Downlight Adjustable Product Overview Features Essenza LED Downlights are designed to deliver the features required for your Hotel and Residential High Rise or Commercial projects. Available with 12W or
More informationHi-lume LED Overview. LED Dimming Driver Hi-lume LED Architectural Dimming
Hi-lume LED Overview Hi-lume LED 1 12.11.9 Hi-lume LED is a high-performance, constant current driver that provides energy-efficient dimming for LED lighting. With industry-leading full-range % to 1% dimming,
More informationBeams Spot (15 to 21.5 ) Narrow Flood (24 to 28.5 ) Flood (38 to 39 ) Wide (60 to 65 ) Reflectors Aluminum reflectors
6" COMMERCIAL RECESSED- Project: Type: Catalogue #: Drawn by: Date: Our commercial recessed 6 inch downlight is available for Non-IC and remodeler construction and is suitable for all commercial lighting
More informationCIRRUS CEILING WALL WASH WITH REMOTE POWER
0.9" 0.9" CIRRUS CEILING WALL WASH (ACTUAL SIZE) CIRRUS CEILING WALL WASH LENS (ACTUAL SIZE) DESCRIPTION At 7.3 or 9.6 watts per foot, Cirrus Channel Wall Wash contains 85+ or 95+ CRI LEDs. Fixture mounts
More informationNOVA SUSPENSION DOWNLIGHT WITH POWER - END FEED
Shown without Louver Description Nova Power Suspension Downlight with a 24VDC power supply in the canopy is a linear LED fixture that offers direct light in a clean, contemporary style. Nova is available
More informationCIRRUS CEILING SQUARE 1 WITH REMOTE POWER
Diffused Square 1 (Actual Size) Description Cirrus Ceiling S1 is a linear LED fixture that offers direct light in a clean, contemporary style. Cirrus is available in various increments from 12" to 720"
More informationHornet 120. Track Head
Features The Hornet 120 edition is designed to meet the specific needs of the competitive Retail market space. A boost in output (while maintaining the high quality of light and durability that Hornet
More information95+ CRI 90+ CRI 95+ CRI. Product Watts Color Temp CRI Version Driver Optional. 3G 3rd Gen
DESPTION The Novation shallow downlight has a height of just -/ inches with an adjustable housing that utilizes a heat pipe module that can tilt up to and rotate a full. W Output Performance Color Temperature
More informationGRX-TVI Ten Volt Interface
Lutron Power Interfaces Ten Volt Interface 36947d 07.07.4 Features 00-77 V~ forward, reverse, and center phase control input capability Provides control and switching capabilities to switch and dim current
More informationThe RSQ LED Series provides continuous dimming with reverse or forward phase cut dimmers.
RSQ All-Purpose Square Lens LED Modules Dimming Guide and Step-down Transformer Application Note HALO The RSQ LED Series provides continuous dimming with reverse or forward phase cut dimmers. RSQ4 RSQ5
More informationGRX-TVI Ten Volt Interface
Lutron Power Interfaces Ten Volt Interface 369247c 1 09.17.13 Features 100-277 V~ forward, reverse, and center phase control input capability Provides 0-10 V- control and switching capabilities to switch
More informationHornet 120. Track Head
Features The Hornet 120 edition is designed to meet the specific needs of the competitive Retail market space. A boost in output (while maintaining the high quality of light and durability that Hornet
More informationORDERING INFORMATION:
HORIZONTAL TRACK HEAD APPLICATION Accent and display lighting for Retail, Commercial and Hospitality environments CONSTRUCTION: Complete die-cast construction No exposed wiring Powder coat paint ELECTRICAL:
More informationProfessional-grade LED downlights
Professional-grade LED downlights High end. Low profile. Affordable price. RABWEB.COM 888 722-000 LED NEW CONSTRUCTION 2W replaces 75W R30, 20W & 26W replace 00W PAR Up to 856 lumens/7 LPW Dimmable down
More informationDesigned to roll with the changes. Affordability and versatility make HALITETM. the modular downlight that adapts to you.
Designed to roll with the changes. Affordability and versatility make HALITETM the modular downlight that adapts to you. HALITETM Modular is putting it mildly. HALITE was designed to be both easily customized
More informationEssenza. Dim-To-Warm Round Downlights
Dim-To-arm Round Downlights Downlight Adjustable Product Overview Features Add ambiance to any hospitality, residential, retail or commercial space. Amerlux Essenza Downlight Dim-To-arm option offers a
More informationRESIDENTIAL GRADE
1 RESIDENTIAL GRADE LEDH-310ICA 3.5 Low Voltage LED IC Rated New Construction Recessed Housing MR16 LED Bulb 4-13/16 (123mm) 3-3/4 (95mm) Ceiling Cut-out : 3-7/8 Lamp, Max, Watt. : 12.2W The LEDH-310ICA
More informationThe HLB SeleCCTable LED Series provides continuous dimming with reverse or forward phase cut dimmers.
HLB SeleCCTable Ultra-thin Downlight Dimming Guide and Step-down Transformer Application Note HALO The HLB SeleCCTable LED Series provides continuous dimming with reverse or forward phase cut dimmers.
More informationGRX-TVI Ten Volt Interface
Lutron Power Interfaces Ten Volt Interface 369247e 1 07.07.16 Features 100-277 V~ forward, reverse, and center phase control input capability Provides control and switching capabilities to switch and dim
More informationIdaho Profile System - Trimless
3 4/16 82mm DIRECT 3 9/16 90mm 3 6/16 85mm L3ID-TRI-SYS DR OP Article # Distribution Diffuser Length Voltage Linear Electrical Mounting Brackets Lighting Control Product Distribution Diffuser Length Voltage
More informationMini Cavaletto. Recessed Adjustable Wall Wash
Recessed Adjustable Wall Wash Features The Mini Cavaletto LED is a compact, recessed adjustable wall wash luminaire for commercial and retail environments. The high-performance optical head with various
More informationPRIME PRIME 4 LED ARCHITECTURAL ROUND FLANGED DOWNLIGHT
TYPE: USE OF PRODUCT The 4" Prime Downlight Series is the ideal product for architectural energy efficient lighting in commercial and residential applications. Available in an assortment of color temperatures,
More informationHornet HP. Square Downlights
Downlight Adjustable (Trimless version shown) Features Small in size but big on performance. The Hornet downlights deliver the output of the 2 ceramic metal halide, but with the control and crisp color
More informationHornet HP. Square Downlights
Downlight Adjustable (Trimless version shown) Features Small in size but big on performance. The Hornet downlights deliver the output of the 2 ceramic metal halide, but with the control and crisp color
More informationLAD6 6 LED Architectural Downlight
Catalog # : Project : Prepared By : Date : LAD6 6 inch LED new construction downlight delivers superior performance and energy efficiency. Designed to use anodized aluminum reflectors delivering even illumination
More informationExterior LED Cylinder Lighting To The Next Level. FCC400 Series. delivering up to 3500 LUMENS! Specification Sheet
FCC400 Series Exterior LED Cylinder Lighting To The Next Level Design & Construction: FC Lighting has developed the latest durable, high ouptut exterior cylinder line on the market. Engineered with a revolutionary
More information