Round or Square Chicago Plenum Hi-lume Wall Wash Housing with LED Lamp for Flanged Trims E3_F_-L_WC-HL 1.0
|
|
- Maurice Foster
- 5 years ago
- Views:
Transcription
1 Installation Instructions for 90ELED-WHL-FL Round or Square Chicago Plenum Hi-lume Wall Wash Housing with LED Lamp for Flanged Trims E_F_-L_WC-HL.0 LED - ROUND/SQUARE FLANGED GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer. This instruction shows a typical installation. CAUTION - RISK OF FIRE This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Use minimum 90 c supply conductors. Install the Housing with Adjustable Bars A B INNER ADJUSTABLE BAR HOUSING NAIL LEAVE TAB IN PLACE BREAK OFF AND DISCARD ½ to ¾ ¾ or thicker HOUSING CLASP NOTE: Skip this section if installing the housing with butterfly brackets. OUTER ADJUSTABLE BAR STOP POINT Keep Tab for ceiling ½ to ¾ thick. When using adjustable hanger bars with ½ to ¾ thick ceilings, leave the tab of the hanger bars in place. Break off Tab for ceiling ¾ or thicker. When using adjustable hanger bars with ¾ or thicker ceilings, remove the tab by bending it at the perforation. TAB Slide the inner adjustable bar completely through the three housing clasps. Make sure the nail is on top. Slide and push the outer adjustable bar completely onto the inner adjustable bar so that the tab clicks into place behind the stop point.this will prevent the adjustable bars from coming apart. Repeat steps & for the other side of the housing.
2 C D 7 NAIL ADJUSTABLE BAR HOUSING NAIL JOIST TRIM HOLDER TRIM HOLDER NOTCH NOTCH NOTE: The adjustable bars can be mounted to joists that are spaced " - " apart. HOUSING Align the bottom of the end plates with the bottom of the ceiling joists. TRIM HOLDER Level the adjustable bars and, with a hammer, tap the nails completely into the joists to secure the adjustable bars in place. # SELF TAPPING SCREW 7 Adjust the trim holder position (horizontal position) by sliding the housing on adjustable bars. When the desired location is achieved, tighten the two # self tapping screws to lock the housing onto the adjustable bars. TIP: Notches in trim holder can be used to align multiple housings using a laser or string.
3 Install the Housing with Butterfly Brackets Connect Power to the Housing A BUTTERFLY BRACKET NOTCH TRIM HOLDER A TABS ELECTRICAL BOX COVER WING NUT NOTE: Skip to page if installing the housing with adjustable bars. Slightly loosen the wing nut to slide the butterfly bracket up or down. B Push up on the tabs on the electrical box and remove the electrical box cover. CONDUIT After achieving the proper location, tighten the wing nut to secure the butterfly bracket in place. Repeat steps and on for the other butterfly bracket. Utilize the butterfly brackets to install the housing in accordance with local electrical codes. TIP: Notches in trim holder can be used to align multiple housings using a laser or string. Install the conduit to the housing electrical box. Run the power line wires into the housing electrical box. WARNING: RISK OF FIRE: When using the housing electrical box for power feed through, use MAX - # AWG, or - # AWG branch circuit wires.
4 Install Drywall and Plaster Ring C A -7/" -7/" ROUND TRIM HOLDER SQUARE TRIM HOLDER Connect the neutral power line wire to the white transformer wire with a wire nut. Connect the hot power line wire to the black thermal protector wire with a wire nut. For round trims, mark a -7/" diameter circle on drywall. Cut out the marked section. For square trims, mark a -7/" square on drywall. Cut out the marked section. Make sure that housing is grounded in accordance with local electrical codes. B 7 Replace the electrical box cover. Make sure that the top edge of the cover snaps under both tabs. For wire dimming applications see diagram below. D Wire Dimming DRYWALL TRIM HOLDER JOIST Align the cut out section of drywall with the trim holder and install drywall WARNING: Risk of Fire: The housing is not intended to be in contact with or covered with combustible materials and insulation. Do not install insulation within inches of the housing sides or above in such a manner to entrap heat. 9 For wire driver applications, properly connect the orange (dimmed hot) and the two purple wires (dimming/digital bus).
5 Replacing the Lamp A Adjust the Lamp Housing A C AUTION:To reduce the risk of a burn or electric shock during relamping, disconnect the power to the fixture. Remove the trim from the fixture. Loosen all three screws from the front cover and pull the LED lamp out.. B FRONT COVER LAMP Ensure that the lens assembly is centered to the aperture by pulling the assembly to the center of the housing.when centered the locking pin will be engaged. B ROTATION LOCK NOTE: Lamp housing can rotate horizontally. Use ONLY WATT proprietary Element Lighting LED lamp. Line up the square and round pegs in the new lamp with the holes in the heatsink and push the new lamp into place. Replace the front cover. Reinstall the trim. Pull the rotation lock down to unlock the lamp housing. Rotate the lamp housing horizontally. When the desired position is achieved push the rotation lock up to lock the lamp housing in place. NOTE: If installing optional lenses, see page for instructions before reinstalling the lamp assembly.
6 Install the Lenses (Optional) 7A 7C ES HOLDER Place lenses (max., optional) inside the lens holder. 7B Line up the legs of the lens holder with the notches on the lamp holder and push the lens holder on. Vertical Alignment Guides Horizontal Alignment Guides Use the lens orientation guides to align linear spread lenses vertically or horizontally.
7 NOTES 7
8 STATEMENT OF WARRANTY Tech Lighting warrants all products manufactured by Tech Lighting to be free from defects in material and workmanship under normal use for a specified period after the date of original purchase as follows: years for LED products; years for Energy Star qualified products; year for all other products. For details, visit our website at: SAVE THESE INSTRUCTIONS! 700 Linder Ave. Skokie, IL Tech Lighting, L.L.C. All rights reserved.the "Element" graphic is a registered trademark of Element. Element reserves the right to change specifications for product improvements without notification.
Round or Square Type Non-IC Adjustable Housing with Toroidal Transformer for Flangeless Trims E3_L_-HANM_ 1.7
Installation Instructions for 90EHMH-ANIC Round or Square Type Non-IC Adjustable Housing with Toroidal Transformer for Flangeless Trims E_L_-HANM_. HALOGEN MR - ROUND/SQUARE FLANGELESS GENERAL PRODUCT
More informationRound or Square Type Low-Profile Housing with Toroidal Transformer for Flangeless Trims E3_LF-HDSM-WR_ 1.0
Installation Instructions for 90EHMH-LNIC Round or Square Type Low-Profile Housing with Toroidal Transformer for Flangeless Trims E_LF-HDSM-WR_.0 HALOGEN MR - ROUND/SQUARE FLANGELESS GENERAL PRODUCT INFORMATION:
More information4" LED SPECIFICATIONS LOW-PROFILE ADJUSTABLE DOWNLIGHT
LED This specification grade low-profile adjustable LED downlight delivers high performance for ultra-shallow ceiling plenum installations while maintaining a beautiful architectural ceiling appearance.
More informationD3 INSTALLATION GUIDE
D3 INSTALLATION GUIDE Supported Models D3-FXRD D3-FXSQ D3-ADRD D3-ADSQ D3-WWRD D3-WWSQ D3 INSTALLATION GUIDE 770-000028-0X r09 PAGE 1 ! WARNING! Shock Hazard. May result in serious injury or death. Turn
More informationOutdoor Installation Using an Electronic LED Power Supply (TE-60L-12)
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 606 Tel: 77-770-9 Fax: 77-9-6 www.edgelighting.com info@edgelighting.com Installation Instructions for Port Round & Square LED PORT-RD-ST-SA
More information2" LED SPECIFICATIONS ADJUSTABLE DOWNLIGHT & WALL WASH
" LED The ELEMENT " adjustable downlight boasts a." aperture and.75" ceiling cutout. Newly developed aiming/locking mechanism offers -5º tilt, 3º rotation, and ELEMENT's patented high-low lamp positioning.
More informationMULTIPLES SPECIFICATIONS 1 X 2 TRIMMED
X TRIMMED ELEMENT Multiples feature a unique patented LED spot dome module enabling remarkable tool-free adjustment and locking while maintaining center beam through the aperture at all tilt and rotation
More informationMULTIPLES SPECIFICATIONS 1 X 4 TRIMMED
X TRIMMED ELEMENT Multiples feature a unique patented LED spot dome module enabling remarkable tool-free adjustment and locking while maintaining center beam through the aperture at all tilt and rotation
More informationCITIZEN CITIZEN WARM DIM XICATO MAX OUTPUT HIGH OUTPUT LOW OUTPUT HIGH OUTPUT LOW OUTPUT STANDARD SERIES ARTIST SERIES
LED This specification grade LED downlight offers high performance with an architectural ceiling appearance. This specification grade LED downlight offers a wide selection of LED module options to address
More informationMULTIPLES SPECIFICATIONS 1 X 1 OPEN
X OPEN ELEMENT Multiples feature a patented LED spot dome module enabling remarkable tool-free adjustment and locking while maintaining center beam through the aperture at all tilt and rotation angles.
More information3" LED SPECIFICATIONS ULTRA SHALLOW FIXED DOWNLIGHT
Small aperture LED downlight with architectural appearance housed in an ultra-shallow " above the ceiling housing. LED module and optics are modular for ease of replacement. Wood ceiling option allows
More information2" LED SPECIFICATIONS ADJUSTABLE DOWNLIGHT & WALL WASH
The ELEMENT " adjustable downlight boasts a.4" aperture and.75" ceiling cutout. Unique aiming/locking mechanism offers -45º tilt, 36º rotation, and ELEMENT's patented high-low lamp positioning. Flanged
More informationIvalo Finiré 3 LED Recessed Lighting Installation Instructions
IMPORTANT INFORMATION Please Read Before Installing 367-2578e 1 09.20.16 Important Notes IC fixtures must be used for installations containing insulating materials and must be mounted away from heat producing
More informationBYOM ELEMENT SPECIFICATIONS BUILD-YOUR-OWN MULTIPLES
ELEMENT BYOM ELEMENT Build-Your-Own Multiples (BYOM) is a uniquely modular recessed led lighting system that puts incredible design flexibility in the hands of the designer. The BYOM grid frame kit system
More informationSection One: Install the Constant Current DMX Driver
Intelligent LED Driver/Controller Output 060VDC, 0050mA, 0W SELV equivalent : 0% typ. in in out out Group Group LEDcode in in out out Group Group LEDcode 06 Edge Lighting. All Rights Reserved. Installation
More informationWARM COLOR DIMMING ARTIST SERIES 21º º º º - N/A 43º - N/A 60º K, 3000K or 3500K*** 3000K-1800K Warm Dim
Small aperture LED downlight with architectural appearance, featuring ELEMENT's unique patented high-low lamp positioning feature. The innovative design allows the LED to be positioned closer to the aperture
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
07 Edge Lighting. All Rights Reserved. Installation Instructions for Pix Stick Tie Stix Suspension -Light, -Light, -Light and -Light with Power IMPORTANT INFORMATION - This product is suitable for indoor
More informationInstallation Instructions MX LED Enhanced Color Adjustable
Installation Instructions 1 of 5 MX Enhanced Color Adjustable Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly.
More informationA CHANNEL. Installation Instructions for Tie Stix Wall 2-Light. Section One: 4SQ Version
0 Edge Lighting. All Rights Reserved. W. Fullerton Ave Chicago, IL 0 Tel: -0- Fax: -- www.edgelighting.com info@edgelighting.com Installation Instructions for Tie Stix Wall -Light IMPORTANT INFORMATION
More information800 TO 9000 LUMEN 8 LED SILENT CEILING DOWNLIGHT HYPERBOLIC OPEN APERTURE L8 SERIES
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Lumen packages suitable for ceiling heights ranging from 8 to over 100 Efficacies up to 109 lm/w Superior-quality white LED light output using Chip on Board technology
More informationAvenue B. Grid Mount (Regress Trim Shown) Flush Lens. Drywall Flange (Regress Trim Shown) Narrow 3" slot LED with frosted satin lens.
LED corrugated regress trim solid regress trim flush lens DIMENSIONAL DATA Grid Mount (Regress Trim Shown) FEATURES Narrow 3" slot LED with frosted satin lens. Shielding options include corrugated or solid
More informationid + 4.5" Downlight mm Trim ChromaSure: Color consistency resulting in a 2-step MacAdam ellipse across the entire ID+ product line.
clear diffuse warm diffuse white painted flange DIMENSIONAL DATA Downlight 12.59 319.8mm FEATURES ChromaSure: Color consistency resulting in a 2-step MacAdam ellipse across the entire ID+ product line.
More information1718 W. Fullerton Ave Chicago, IL Tel: Fax:
206 Edge Lighting. All Rights Reserved. Installation Instructions for Nova Power Suspension Up/Down - Center Feed Glide Up/Down - Center Feed IMPORTANT INFORMATION - This product is suitable for indoor
More informationid + 4.5" x 4.5" Downlight mm Trim ChromaSure: Color consistency resulting in a 2-step MacAdam ellipse across the entire ID+ product line.
white flange black flange titanium silver flange clear diffuse warm diffuse DIMENSIONAL DATA Downlight 12.21 31.1mm FEATURES ChromaSure: Color consistency resulting in a 2-step MacAdam ellipse across the
More informationInstallation Instructions for Monorail 2 Circuit 2 X 250 Watt Sloped Surface Mount Magnetic Transformer 120 Volt Input to 12 Volt Single Feed Output
0 Edge Lighting. All Rights Reserved. 78 W. Fullerton Ave Chicago, IL 0 Tel: 77-770-9 Fax: 77-9- www.edgelighting.com info@edgelighting.com MT-X0--SL_ 90-MT-X0--SL-0 Installation Instructions for Monorail
More informationINSTALLATION INSTRUCTION Aether 2 Shallow Recessed Housing
SAFETY INSTRUCTIONS IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance
More informationid + 6" x 6" Downlight mm Trim ChromaSure: Color consistency resulting in a 2-step MacAdam ellipse across the entire ID+ product line.
white flange black flange titanium silver flange clear diffuse warm diffuse DIMENSIONAL DATA Downlight 12.81 325.4mm FEATURES ChromaSure: Color consistency resulting in a 2-step MacAdam ellipse across
More informationCustomer service: or Upper mounting ring. Canopy
Components included: Upper mounting ring Canopy Fixture base Fluorescent - 2 x 42 W 4-pin compact fluorescent lamps required (not included). Lutron recommends GE, Sylvania, or Philips lamps that are certified
More informationInstallation Instructions for Sun 3 RGB LED. Section One: Install the Constant Current DMX Driver
Intelligent LED Driver/Controller Output 060VDC, 00050mA, 00W SELV equivalent : 90% typ. in in out out in in out out Group Group Group LEDcode Group Group Group LEDcode 06 Edge Lighting. All Rights Reserved.
More informationSquare Trim Style Reflector Finish Flange Style / Finish Environmnet Ceiling Installation. Available for 3SQD, 3SQWW only. 5
PRODUCT SPECIFICATIONS LED Light Engine Consistent fixture to fixture color within 3-step MacAdam ellipse 2700K, K, 3500K, or 4000K color temperatures are available with 80 CRI minimum 2700K and K also
More informationLuminaire PROFILE-SPOKE 15 UP 85 DN LED (PS1-D) Type. Notes. Performance Summary D OPTIONS 3S A 28 W B 34 W C 44 W D 57 W
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE - SPOKE Specification Data Luminaire PROFILE-SPOKE 15 UP 85 DN LED () Type Project Profile Spoke 3 (S3) Product Notes Profile Spoke 4 (S4) Performance
More informationInstallation Instructions 4 Gravity Enhanced Color Adjustable
Installation Instructions 1 of 5 Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. will fail if not installed properly. Follow installation
More informationProject. Comments. Prepared by
DESCRIPTION Recessed 6-inch LED wall washer is available in various lumen and CRI/CCT options. Suitable for commercial construction and can be used for both new or renovation work. Insulation must be kept
More informationSERIES 6VLFL2X Lensed LED Downlight Lumen Flex
APPLICATION Small-aperture medium-distribution downlight is suitable for commercial, retail and institutional applications that require an energy saving, long life LED lamp source, high lumen output, excellent
More informationJandy Pro Series WaterColors LED Lights Underwater Large and Small Light
installation Manual English Jandy Pro Series WaterColors LED Lights Underwater Large and Small Light FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified
More informationMIRRORLITE RECESSED EMERGENCY LIGHTING
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. MIRRORLITE RECESSED EMERGENCY LIGHTING INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should
More informationNIOB-2 2" BWF IOLITE TRIMS
NIOB-2 2" BWF IOLITE TRIMS New Construction or Remodel Housing Required Source: LED, 14 Watts, 8 Lumens Nora Lighting s 2" Iolite BWF trims are small aperture downlights that can be specified for use in
More informationINSTALLATION INSTRUCTION Oculux 3.5" Architectural Downlight R3CRN-11, R3CSN-11
. INSTALLATION INSTRUCTION SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified
More informationTOPAZ 12 WALL PACK INSTALLATION & MAINTENANCE GUIDE (Part # LIT A)
TOPAZ 12 WALL PACK INSTALLATION & MAINTENANCE GUIDE (Part # LIT-29499-1A) Contractor: Please read these instructions before starting installation. After installation, please forward this guide to the user
More informationE E VDC COOLEDGE TILE INTERIOR INSTALLATION INSTRUCTIONS. Caution: Observe precautions for handling electrostatic sensitive devices.
5 YEAR WARRANTY 5 YEAR WARRANTY COOLEDGE TILE INTERIOR INSTALLATION INSTRUCTIONS E354088 LISTED AC E354088 58VDC E354088 E354088 5 5 YEAR WARRANTY 5 YEAR WARRANTY E354088 Caution: Observe precautions for
More informationNRM2-511 / NRM2-512 / NRM2-518
HIGH EFFICACY LED LIGHT SOURCE REQUIREMENTS ILLUMINATING THE FUTURE...SINCE 1989 NRM2-511 / NRM2-512 / NRM2-518 5" Marquise II Reflectors Marquise II COB Series enhances an established series of downlighting
More informationDMXR DALI. Must specify 120 or 277 volts. Available on EZ1 and EZB only 5. Available on 4ABV and 4DBV only 6. Available on 4AC, 4AC20, 4DP, 4WW only
PRODUCT SPECIFICATIONS LED Light Engine Consistent fixture to fixture color within 3-step MacAdam ellipse 2700K, K, K, or K color temperatures are available with 80 CRI minimum 2700K and K also available
More informationAsymmetrical Installation Instructions. Components: i2cove Asymmetrical LED Light Fixtures. 12 [305mm] [918mm] 48.
support@i2systems.com www.i2systems.com Electrical Specifications PARAMETER Input Power VALUE 8 Watts* / Ft Input Voltage 120-277V AC, 50/60 Hz Max. Fixture Run Length LED Color (CCT) 8 Watts: 120VAC:
More informationLuminaire PROFILE-SPOKE Ind. Up Dn Control (PS3-B) Type. Project. Notes. Performance Summary OPTIONS 4S D 76 W 3S D 57 W
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE - SPOKE Specification Data Luminaire PROFILE-SPOKE Ind. Up Dn Control () Type Project Profile Spoke 3 (S3) Product Notes Profile Spoke 4 (S4) Performance
More informationLIGHTPLANE 1 RECESSED - LP1R
INSTRUCTIONS LIGHTPLANE 1 RECESSED - LP1R Safety & Warnings! When installing or using this recessed fixture basic safety precautions should be followed: 1. Read ALL INSTRUCTIONS before installing 2. This
More information13 3/4" Will expand to 24 3/8" (Reduces to 10 3/4" with breakaway feature) 19 5/8"
PRODUCT SPECIFICATIONS Cutoff visual cutoff to lamp and lamp image Trims Style Die Cast Self Flanged and reflectors utilize precision wound double torsion springs for tight, secure fit to ceiling Flange
More information32LM 3200 Lumens ECOS2 Lutron Hi-Lume A series 2-wire forward phase, 1% dim. Must specify 120 or 277 volts 5. Available on 24D only 6
PRODUCT SPECIFICATIONS LED Light Engine Consistent fixture to fixture color within 3-step MacAdam ellipse 2700K, K, 3K, or K color temperatures are available with 80 CRI minimum 2700K and K also available
More informationSERIES 6LB79V-NF LENSED Lumen Bridgelux LED Recessed Downlight
APPLICATION These high-lumen fixtures are ideally suited for lobbies, auditoriums and many other applications with high ceilings, where superior light output is needed. PRODUCT DATA REFLECTOR: Spun aluminum
More informationDIMENSIONS. 13 3/4" Will expand to 24 3/8" (Reduces to 10 3/4" with breakaway feature) 8 15/16" 15 1/8" 19 5/8" IC43N
PRODUCT SPECIFICATIONS Cutoff visual cutoff to lamp and lamp image Trims Style, Self Flanged and Trims utilize torsion spring retention for tight, secure fit to ceiling Trim ring features beveled knife
More informationPROFILE 50 Up 50 Dn PF1-E. Luminaire PROFILE - 50 UP 50 DN LaED (PF1-E) Type. Project. Product. Notes. Performance Summary
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE Specification Data PROFILE - 50 UP 50 DN LaED () Type Project Product Notes 50 Up I 50 Down A B C D Light (lm) 2350 2900 3500 4450 Energy (W) 19 24
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationINSTALLATION INSTRUCTION Aether 3.5 Color Tunable LED Downlight
SAFETY INSTRUCTION IMPORTANT: NEVER attempt any work without shutting off the electricity. Read all instructions before installing. System is intended for installation by a qualified electrician in accordance
More informationElle Surface Mounting Instructions
Step 1: Preparation, page 2 Warnings CAUTION risk of fire and this product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation
More informationAvenue A. Grid Mount (Open Shown) Drywall Flange (Open Shown) louver lens mr16
FLUORESCENT MR16 open optic cut-off louver clear lens flush mount mr16 (35 adjustment) extended yoke mr16 ( adjustment) snoot hex louver linear prismatic sand blasted soft focus DIMENSIONAL DATA Grid Mount
More informationTrim Style Reflector Finish Flange Style / Finish Environment Ceiling Installation
PRODUCT SPECIFICATIONS Cutoff visual cutoff to lamp and lamp image. Trims Style, Self Flanged and Trims utilize torsion spring retention for tight, secure fit to ceiling Trim ring features beveled knife
More informationQUICK START INSTALLATION GUIDE ANALOG - INTELLIGENT POWER CENTER (IPC)
Intelligent LED Lighting Systems TM QUICK START INSTALLATION GUIDE ANALOG - INTELLIGENT POWER CENTER (IPC) LIGHTS & POWER: (Note all lights fixtures to be wired in series) 1) Identify dry, non-plenum location
More informationProject. Comments. Prepared by
DESCRIPTION Recessed 6-inch LED wall washer is available in various lumen and CRI/CCT options. Suitable for commercial construction and can be used for both new or renovation work. Insulation must be kept
More informationID+ 3.5" x 3.5" 60 cut-off reflector. 50 cut-off reflector. Less than 2.64" low profile housing available.
clear diffuse warm diffuse black flange titanium silver flange die-cast black die-cast white trimless companion DIMENSIONAL DATA 6 cut-off reflector 12.88" 327.2mm FEATURES Less than 2.64" low profile
More information2000 LUMENS A3-LED. Submittal form is Tel: Fax:
UPTO 2 LUMENS DESCRIPTION: Achieve all of your lighting application objectives with only one universal high-performance architectural housing. The Fusion A3-LED is a 3 LED Universal Downlight that can
More informationNRM-511 / NRM-512 / NRM-518
HIGH EFFICACY LED LIGHT SOURCE REQUIREMENTS ILLUMINATING THE FUTURE...SINCE 1989 NRM-511 / NRM-512 / NRM-518 5" Marquise I Reflectors 5" Marquise Series with thermal management system combined in a single
More informationInstallation Instructions BLTR and 2BLTR Relight Assembly
UT4540 Rev. B Installation Instructions BLTR and 2BLTR Relight Assembly This Relight assembly was engineered to upgrade most recessed fixtures mounted in T-grid ceiling installations, including most parabolic
More informationnissan patrol birfield kit
nissan patrol birfield kit 300795-kit 1987-1997 nissan patrol gr(y60) 1988-1994 ford maverick 1987-1997 nissan patrol gq 1987-1997 nissan patrol safari 1987-1997 nissan safari kit contents 5356 PINE AVE
More informationHIGHBAY RAIL 400W INSTALLATION INSTRUCTIONS
TM INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical Code and
More informationLuminaire PROFILE-SPOKE 40UP 60 DN LED (PS1-A) Type. Notes. Performance Summary OPTIONS CONTROLS
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE - SPOKE Specification Data Luminaire PROFILE-SPOKE 40UP 60 DN LED () Type Project Profile Spoke 3 (S3) Product Notes Profile Spoke 4 (S4) Dw DYNAMIC
More informationProject name. Qty. Output (nominal lumens) Colour and colour temperature. Optics (nominal distribution) Narrow spot 10, Narrow 20, Medium 40
D u m m y Specification sheet Client Project name Order# Type Qty Side view Bottom view Photometric Summary Description The Lumenalpha Soft Nano Tilt is a high-performance LED downlight for accenting and
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationReflectors are compatible with respective Marquise II series housings manufactured by Nora Lighting.
HIGH EFFICACY LED LIGHT SOURCE REQUIREMENTS ILLUMINATING THE FUTURE...SINCE 1989 NRM2-611 / NRM2-612 / NRM2-618 6" Marquise II Reflectors 6" Marquise II reflectors includes Cree COB LEDs with optimized
More informationAvenue B. Narrow 3" slot LED with frosted satin lens. Shielding options include corrugated or solid regressed trim or flush lens.
LED corrugated regress trim solid regress trim flush lens DIMENSIONAL DATA FEATURES Narrow 3" slot LED with frosted satin lens. Shielding options include corrugated or solid regressed trim or flush lens.
More informationInstallation Instructions MX LED Downlight Remodel
1 of 5 Risk of electrical shock. Disconnect power before servicing or installing luminaire. Risk of injury or damage. Luminaire will fail if not installed properly. Follow installation instructions. Risk
More informationELS Electronic Lighting System
ELS Electronic Lighting System T-8 Lamp Replacement November, 2012 99-20374-I001 I. T-8 Lamp Replacement Instructions Center Mullion Fixtures 1. Turn light power off before start of lamp replacement. 2.
More informationAquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
16 1 AquaLumin III - Nicheless Light Installation Guide IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationEssenza. Round Downlights
Downlight Adjustable Product Overview Features Essenza LED Downlights are designed to deliver the features required for your Hotel and Residential High Rise or Commercial projects. Available with 12W or
More informationElle Surface Mounting Instructions
Step 1: Preparation, page 2 Warnings CAUTION risk of fire and this product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation
More informationINSTALLATION INSTRUCTIONS
LED LIGHT ENGINE APPLICATION PROGRAM INSTALLATION INSTRUCTIONS LED Light Engine Kit Model: 9 Round Engine 120V: TRIAC DIMMING TKT120025RDxx-01 TKT120025RDxx-11 TKT120021RDxx-01 TKT120021RDxx-11 TKT120025RDxx-02
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.
Installation Instructions RT8RT/RT5RT Relight Assembly READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION. IMPORTANT SAFETY INSTRUCTIONS WARNING: FAILURE
More informationSkydome. 2', 3' and 4' diameter recessed direct LED with lens. Frosted acrylic diffuser provides high transmission and uniform distribution.
LED DIMENSIONAL DATA FEATURES 2', 3' and 4' diameter recessed direct LED with lens. Frosted acrylic diffuser provides high transmission and uniform distribution. 24." 69.6mm 36." 914.4mm 48." 1219.2mm
More informationOutput (nominal lumens) 700 lm, 1000 lm, 1300 lm, 2000 lm, 3000 lm, 4000 lm, 5000 lm. Color and color temperature
Dummy Specification sheet Front view Bottom view Photometric summary Description The Lumenalpha Clear Large is a high-performance fixed LED downlight for high-ceiling applications. Delivering up to 5000
More informationLED IMPORTANT SAFETY INSTRUCTIONS
LED IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION To reduce the risk of death, personal injury or property damage
More information95+ CRI 90+ CRI 95+ CRI. Product Watts Color Temp CRI Version Driver Optional. 3G 3rd Gen
DESPTION The Novation shallow downlight has a height of just -/ inches with an adjustable housing that utilizes a heat pipe module that can tilt up to and rotate a full. W Output Performance Color Temperature
More informationPD404-AN V analog control 4 Channel x 500 W Dimmer & Switch Packs ANALOG 0-10 V. Serial Number
0-10V analog control 4 Channel x 500 W Dimmer & Switch Packs ANALOG 0-10 V 4 circuit Analog 1-10V 4 x 4 A. Dimmer pack Serial Number Dimmers Indicators Digital Lighting Systems,Inc Info@digitallighting.com
More information6" LED Downlight LC6LED 120 or 277V 0-10V Dimming Option
6" LED Downlight LC6LED 120 or 277V 0-10V Dimming Option Date: firm name: PROJECT: type: APPLICATIONS: LiteFrame Commercial (LC6LED) is a 6" commercial grade LED downlight with available outputs between
More informationBLACK BODY DIMMING 800/1300/1500 LUMEN 6 LED NEW CONSTRUCTION/REMODEL
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Black Body Dimming duplicates halogen dimming, offering a soft, natural, warm glow as light levels are reduced CCT warms from 3000K to K, while staying on the
More informationSERIES 6LCDB79V Low Voltage LED Downlight
APPLICATION Low voltage LED lighting fixtures using remote driver platforms are ideally suited to applications that require easy access to LED drivers for routine maintenance and improved LED life and
More informationUV8 & UV90 SERIES INSTALLATION INSTRUCTIONS
UV8 & UV90 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationID+ 6" x 6" trim. High ceiling downlight with a choice of beamspreads is ideal for lobbies, atriums and convention centers.
LED HIGH CEILING DOWNLIGHT wall wash companion DIMENSIONAL DATA FEATURES High ceiling downlight with a choice of beamspreads is ideal for lobbies, atriums and convention centers. Optical design creates
More informationSERIES 4LBV-NF Flush Mount Lumen Bridgelux LED Lensed Downlight
APPLICATION These high-lumen fixtures are ideally suited for lobbies, auditoriums and many other applications with high ceilings, where superior light output is needed. Suitable for commercial, retail,
More informationavenue led features dimensional data performance Narrow 3" slot LED with frosted satin lens.
led features Narrow 3" slot LED with frosted satin lens. Shielding options include corrugated or solid regressed trim or flush lens. Avenue B LED allows ceiling tiles to rest on fixture rails, keeping
More informationLED Flat Panel Installation Instructions For 1 x4, 2 x2, and 2 x4 LED Flat Panels (FP Series)
LED Flat Panel Installation Instructions For 1 x4, 2 x2, and 2 x4 LED Flat Panels (FP Series) PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION SAFETY
More informationNOVA suspension up and down, end feed with remote power supply
Shown without Louver Shown with White Louver Description Nova Suspension Up/Down is a linear LED lighting 2 circuit system that features both direct and indirect light. This contemporary system allows
More informationReflectors are compatible with respective Marquise I series housings manufactured by Nora Lighting.
HIGH EFFICACY LED LIGHT SOURCE REQUIREMENTS BATTERY PACK NRM-6 / NRM-62 / NRM-68 6" Marquise I Reflectors 6" Marquise Series with thermal management system combined in a single compact unit. Cree TrueWhite
More informationNOTCH 2 Symmetric - NT1-B. Luminaire NOTCH 2 - Area 100 Dn Symmetric (NT1-B) Type. Project. Product. Notes. Performance Summary
T F W 604.549.9379 604.549.9555 fluxwerx.com NOTCH 2 Symmetric - Specification Data Luminaire NOTCH 2 - Area 100 Dn Symmetric () Type Project Product Notes D2 - Drywall Trimless shown with (E) Dado Endcap
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
1 AQUALUMIN III NICHELESS POOL LIGHT INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Section Contents 1. Installing a mounting bracket and light
More informationRECESSED WALL WASH MOUNT
PROJECT INFORMATION Project: Notes: Type: DIMENSIONS SECTION VIEWS 3 13/32 4 3/8" 4" IC culus Listed Type I.C. SHOWN WITH LENS OPTION ORDERING CODE 2 15/16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PRODUCT SPECIFICATIONS
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationProject. Comments. Prepared by
DESCRIPTION Recessed 6-inch ED shallow lens downlight is available in various distributions, lumen and CRI/CCT options. Suitable for shallow commercial construction and can be used for both new or renovation
More informationPROFILE 100 Dn PF1-B. Luminaire PROFILE DN LED (PF1-B) Type. Project. Product. Notes. Performance Summary
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE Specification Data PROFILE - 100 DN LED () Type Project Product Notes LED Product Partner Dw DYNAMIC WHITE 100 Down A B C D Light (lm) 2100 2550 3100
More informationCylindrix III. Recessed Multiples
Features Cylindrix III Recessed LED, the best combination of optical and thermal performance, aesthetics and visual comfort in an recessed accent. Features a deeply recessed single LED light source for
More informationMONORAIL KITS INSTALLATION INSTRUCTIONS SPOTS
MONORAIL KITS INSTALLATION INSTRUCTIONS SPOTS JESCO Lighting Group is a UL and ETL listed company Copyright 2011 JESCO Lighting Group. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS Be sure to read
More informationEssenza. Dim-To-Warm Round Downlights
Dim-To-arm Round Downlights Downlight Adjustable Product Overview Features Add ambiance to any hospitality, residential, retail or commercial space. Amerlux Essenza Downlight Dim-To-arm option offers a
More informationHBDBM High Bay Series
HBDBM High Bay Series INSTALLATION INSTRUCTIONS The High Bay Luminaire is ideal for installations with mounting heights over 25 feet. The fixture can be mounted with a hook or pendant with flexible adjustments
More information