INSTALLATION GUIDE MANUAL SHADE

Transcription

1 PRODUCT OVERVIEW " Fascia 1. Idle End Plug 2. Shade Band 3. Clutch 4. 3" Fascia Bracket 5. 3" Fascia Bracket Cover 6. 3" Chain Diverter 7. 3" Chain Diverter Cover (required for SL10 & SL15 clutches) 8. Stop Bead (attached in field) 9. Stainless Steel Bead Chain 10. Chain Connector 11. Chain Guide 12. Heat-Sealed Hem Pocket 13. 3" Fascia 13 4" Fascia 14. 4" Fascia 15. 4" Fascia Clip 16. 4" Fascia Bracket Cover 17. 4" Fascia Brackets

2 STANDARD BRACKET FASCIA BRACKET JAMB MOUNT TOP MOUNT JAMB MOUNT TOP MOUNT Install brackets 1. Use a minimum of two fasteners suitable for the mounting surface per bracket. 2. Mount control, intermediate, and idle brackets. Note: Make sure that the screw heads clear the clutch. The open end of the fascia brackets faces downward, as shown in the drawings. Heavier shades may require more fasteners. WALL MOUNT WALL MOUNT

3 3" FASCIA SHADE INSTALLATION Figure 1 Figure 2 Figure 3 Figure 4a Figure 4b Figure 5 1. Insert chain diverter into the bracket designated for the clutch and snap it into place. (See Figure 1) 2. Align and hook the clutch into the drive end bracket. (See Figure 2) 3. Compress idle end plug on the inside section of the bracket. Slide the idle end up the bracket ramp into the center hole. (See Figure 3) 4. Check that idle pin and clutch hooks are fully seated in each bracket. (See Figures 4a and 4b) 5. Route the front chain through the center of the diverter and the back chain through the back of the diverter. (See Figure 5) 6. Insert chain diverter cover onto the chain diverter until it is fully seated. (See Figure 6) NOTE: The chain diverter cover is not used with the TruePerformance TM SL20 clutches. 7. Remove paper bands by hand. Do not cut off paper bands. (See Figure 7) Figure 6 Figure 7

4 4" FASCIA SHADE INSTALLATION Figure 1 Figure 2 Figure 3a Figure 3b 1. Place the idle end pin into the center hole in the idle bracket. (See Figure 1) 2. Compress the idle end spring, and align and hook the clutch into the drive end bracket. (See Figure 2) 3. Check that idle pin and clutch hooks are fully seated in each bracket. (See Figures 3a and 3b) 4. Remove paper bands by hand. Do not cut off paper bands. (See Figure 4) Figure 4

5 4" FASCIA CLIP INSTALLATION Flange Angled Tab Figure 1 1. Insert the 4" fascia clip through the bottom slot on the face of the bracket. (See Figure 1) 2. Press firmly on the clip until the bracket is seated behind the angled tab. (See Figure 2) Figure 2 3" AND 4" FASCIA INSTALLATION Figure 1a (3" fascia bracket) Figure 1b (4" fascia bracket) 1. Hook the fascia to the top of the bracket. (See Figures 1a and 1b) 2. Gently press at the bottom until the fascia fully snaps onto the bracket. Note: Fascia brackets may have to be lowered if head is not level. 3. Before attaching the fascia bracket cover, prepare bracket by cleaning debris and dust. Remove adhesive backing and attach cover to bracket. (See Figures 2a and 2b) Figure 2a (3" fascia bracket) Figure 2b (4" fascia bracket)

6 CHAIN GUIDE INSTALLATION IMPORTANT: Chain guide must be installed for proper shade operation. 1. Unwrap control chain loop and determine a mounting location for the guide on the wall or jamb. 2. With the control chain loop under minimal tension, compress the guide and install screw. WARNING: The chain guide reduces the hazards of strangulation and entanglement of young children by limiting access to the control chain. SET UPPER/LOWER LIMITS Stop Bead Stainless Steel Bead Chain 1. Roll shade to lower limit position. 2. Attach stop bead next to the clutch on the front of the chain of a regular roll shade or the back of the chain of a reverse roll shade. 3. Raise the shade to its upper limit position. 4. Attach the stop bead next to the clutch on the back of the chain of a regular roll shade or the front of the chain of a reverse roll shade. OPERATION Pull chain in front to raise shade; pull chain in back to lower shade. The opposite is true for reverse roll.

7 MAINTENANCE Lightly vacuum panels with a soft brush attachment or wipe with a duster. Do not use liquid cleaning solutions. Shades may also be gently wiped with a clean damp cloth. Allow the shade to dry completely before raising. Do NOT completely immerse.