Horizontal Impactor. SPECIFICATION - Rev 1. 19/10/09

Transcription

1 Horizontal Impactor SPECIFICATION - Rev 1. 19/10/09

2 The Powerscreen Pegson XH320 Horizontal Shaft Impactor is a highly compact tracked crusher designed to reinforce a world class range of tracked machines. The Powerscreen Pegson XH320 offers both excellent reduction & high consistency of product yield. The Powerscreen Pegson XH320 is designed to give optimum performance in both quarry & recycling applications and is an ideal mid size contractors machine due to it s compact design and mobility. Proven Terex Impact Crusher with hydraulic overload protection, 4 bar rotor & twin apron design Fully independent under crusher vibrating pan feeder Modular conveyor with raise/lower facility to aid clearance of rebar Suitable for a variety of feed materials Designed to give optimum performance in both quarry & demolition Throughput of up to 320 tph (353 stph) Powered by a 325 hp (242 kw) Caterpillar C9 Tier III ACERT powerpack Hydraulically operated clutch & highly fuel efficient direct drive system Crusher speed variation through user friendly PLC control system Load management system to control feeder speed Double deck grizzly feeder with underscreen 31 tonnes (68,350 lbs) total machine weight Powerful overband magnet (optional) Fully supported by Powerscreen worldwide distribution network Page 2

3 Principle Components of the Powerscreen Pegson XH320 Crusher Opening Rubber Curtain Chain Curtain Wear Liners Inlet Chute Inlet Wear Beam Full Blowbar Principles of Operation Impact Crusher Apron Adjustment Spindle Control Cylinder Top Impact Apron Apron Adjustment Spindle Bottom Impact Apron Control Cylinder Rotor Half Blowbar Material enters via crusher opening and slides down the inlet chute where it is struck by the blowbars fixed within the rotor. This initial impact breaks the material which is then accelerated towards the top apron where more reduction takes place on impact. This material then falls back onto the blowbars and the cycle is repeated until the material is small enough to pass between the top apron and blowbar. Further reduction occurs on the bottom apron until the material can again pass through the gap and discharge from the underside of the crusher. Should an un-crushable object enter the chamber, the overload cylinders will relieve and allow the object to pass. The cylinders will then return to the pre-set crushing position. The pre-set gap is adjusted by turning the adjustment spindle whilst the weight of the apron is held on the cylinder (hydraulic assist). The hydraulic cylinders are pre-loaded to minimise apron bounce and wear on the cylinders. This arrangement also greatly reduces the oversize produced and is Patent Pending GB Main Crusher Specification Feed opening: 1130mm x 800mm (44.5 x 31.5 ) Maximum piece size 450mm 3 (18 inches 3 ) depending on material and blowbar spec Rotor width: 1100mm (43.3 ) Rotor diameter: 1040mm (41 ) Number of aprons: 2 Maximum setting: 180mm (7 ) upper apron; 75mm (3 ) lower apron Minimum setting (CSS) 60mm (2.4 ) upper apron and 20mm (0.75 ) lower apron Number of blowbars: 4 Blowbar removal: Vertically Blowbar configuration: 2 full and 2 half (Optional 4 full) Setting adjustment: Hydraulic assist Overload protection: Hydraulic Rotor speeds: rpm (33-40 m/s) ( ft/s) Applications: Demolition/Recycling/Quarry Crusher weight: 8500 kg (18,740 lbs) Full Blowbar weight: 220 kg (485 lbs) Side liners: 20mm (0.75 ) thick, abrasive resistant steel Page 3

4 Chain Curtain Cover Main Welded Body Impactor Hinged Section Inspection Covers Hydraulic Overload and Adjustment Cylinders Toggle Bolts Side Door Inspection Covers Trunions Hinged Section Opening Cylinders Main Features Bearings Crusher body: Rotor: Bearings: Aprons: Drive: Lubrication: Blowbars: Fabricated from steel plate and fully lined with replaceable abrasion resistant liner plates. Hinged side door allows access to apron tips and rotor for gap measurements and inspection. Complete hinged section opens hydraulically to allow blowbar removal and replacement, apron and liner replacement or major maintenance Cast steel and fitted with four reversible and replaceable blowbars Double row self aligning spherical roller bearing fitted each end of rotor Cast steel aprons with replaceable abrasion resistant wear plate on tip of bottom apron Direct through wedge belts with tensioning system on the powerpack Rotor bearings are greased and fitted with inner and outer labyrinth seals Standard Blowbar is martensitic steel. High chrome and Ceramic Blowbars optional This plant is designed for both demolition and quarrying applications. When fitted with Martensitic or Ceramic Blowbars the crusher will tolerate small quantities of steel reinforcing bar in the feed. However, the machine is not designed to accept large pieces of steel or other un-crushable objects, and the feed material should be assessed / inspected for suitability prior to crushing. It is vitally important that large pieces of steel or similar un-crushable objects are not allowed to enter the crushing chamber as severe damage and injury may occur. When high chrome bars are fitted all steel should be removed from the feed material. The machine should only be used on quarry applications or clean materials such as asphalt. Page 4

5 Hopper Low profile hopper, rigid hopper sides, no setup required, mounted directly to chassis. Hopper length: 4.04 m (13 3 ) Hopper width: 2.1 m (83 ) Hopper capacity: Hopper body: 3.6m 3 (4.7 cu yds) level 10mm (0.4 ) thick abrasion resistant steel plate Grizzly Feeder Vibrating grizzly feeder pan with efficient, self cleaning integral two stage grizzly section. Type: Fully sprung vibrating pan Length: 3.87m (12 8 ) Width: 1080mm (42.5 ) Pan: 10mm (0.4 ) thick abrasion resistant base plate Drive unit: Twin heavy duty cast eccentric shafts, running in spherical roller bearings, gear coupled at drive end Drive: Grizzly: Screen: Control: Chute: Flange mounted hydraulic motor Two stepped sections, 950mm (37.4 ) long. Finger nominal spacing 42mm (1.65 ) Removable rubber blanking mat fitted as standard. Mesh screens optional Variable speed control via control panel & on optional radio remote where specified Plant features bypass chute with internal two way flap door that controls direction of fines, either forward onto the product belt or down onto the optional side conveyor where specified Page 5

6 Product Conveyor Conveyor features: Belt specification: Fully removable modular unit Hydraulic raise and lower facility to increase clearance and aid rebar removal Hydraulic raise and lower facility can be operated whilst crushing Conveyor is shallow troughed with rollers at the lower end and a steel tray design above magnet discharge area Conveyor is fully tunnelled with minimal snag areas EP630/4 with 6mm top and 2mm bottom heavy duty rubber covers and vulcanised joint Belt width: 1000mm (39 ) Discharge height: Feedboot: Impact area: Skirting: Drive: Lubrication: Belt covers: Belt adjustment: Pressure sensor: 3.45m (11 4 ) in fully raised position Fabricated steel with abrasion resistant steel liners Under crusher pan feeder Fully skirted in wear resistant rubber up to magnet discharge area Hydraulic motor direct to head drum Centralised greasing bank, for shaft bearing lubrication Canvas type removable dust covers are fitted over the exposed section of the conveyor. Optional steel head drum hood available Belt tensioning is by use of screw adjustment at the head drum Designed to stop plant feed if the discharge conveyor slows or stops Page 6

7 Product Conveyor and Pan Feeder Interface Vibrating Pan Feeder Type: Steel bodied vibrating feeder fitted with abrasion resistant liners, mounted under the crusher and designed to prevent any impact damage to the product conveyor belt Width: 990mm (39 ) Length: 2.44m (8 ) Drive: Speed: Hydraulic, out of balance exciter unit rpm fixed Dust Suppression System Spray bars with atomiser nozzles are mounted over the product conveyor feed and discharge points, piped to an inlet manifold for customer water supply or optional pump Type: Inlet: Inlet pressure: Water supply: Clean water multi atomising nozzles Single point 3 Bar (44 psi) 24 L/min (6.34 G/min) minimum Page 7

8 Powerunit Engine: Caterpillar C9 Tier III ACERT Six cylinders, four stroke, direct injection Performance: 325HP (242kW) at 2000rpm, ambient temperature +49 C and 12 C (120F and 10F) and at altitudes up to 1000m (3281 ft) above sea level. Fuel tank capacity: 425 L (112 G) - Sufficient to run a 12 hour shift Clutch type: Highly efficient, PT-Tech dry plate clutch with electro-hydraulic operation and control Typical fuel consumption: 38 L/hr (10 G/hr) Up to 6.5 tonnes tons of crushed product per litre of fuel consumed (25 tons/g) Crusher drive: Direct drive via wedge belts Clutch pulley diameter 224mm (8.8 ) Crusher pulley diameter 630mm (24.8 ) Engine drive: Crushing performance can be tuned simply by changing engine speed between rpm on the PLC without significant loss of engine performance Plant drive: High quality belt driven pumps driven direct from engine crankshaft Crusher drive belt tensioning: Manually adjustable screw tensioners located under powerpack Operating Conditions Powerscreen equipment complies with CE requirements. The plant and powerunit are designed to operate between ambient temperatures between +49 C and 12 C (120F and 10F) and at altitudes up to 1000m (3281 ft) above sea level. For applications outside this range please consult with Powerscreen as the plant performance / reliability may be affected. Page 8

9 Crawler Tracks Type: Heavy duty, 2 speed, bolt on tracks Track centres: 3300mm (10 10 ) Shoe width : 400mm (15.7 ) Gradient: High speed : Low speed : Drive : Tensioning: 30 degrees maximum 1.0km/hr (0.62 mph) 0.3km/hr (0.2 mph) Hydraulic Hydraulic adjuster, grease tensioned Guarding Wire mesh or sheet metal guards are provided on all drives, flywheels, pulleys and couplings The guards provided are designed and manufactured to CE & ANSI standards Platforms Platforms are provided for maintenance on one side of the feeder and Impactor. These are fitted with double row handrails and access ladders. Platforms are also provided to gain access to the rear of the crusher and the powerpack. Galvanised walkways as standard. Chassis Heavy Duty I-Section welded construction, provides maximum strength and accessibility. Page 9

10 Plant Controls Full PLC control system 320 x 240 pixel backlit screen Complete pictorial user controls Multi-function backlit menu buttons High definition screen Full system diagnostics A navigation wheel is fitted onto the control system to operate the following items: Sequential start up Engine/Crusher speed Feeder (Start/Stop/Speed) Product conveyor & pan feeder (Start/Stop) Product conveyor Raise/Lower Dirt conveyor Crusher control Umbilical Controls An Umbilical Control Unit is supplied as standard with the plant Controls tracking function and has a stop button for the plant Optional Extras High chrome blowbars Ceramic Blowbars Four full size hammers in lieu of two full and two half hammers Hydraulic folding extended hopper Single pole overband magnetic separator Twin pole overband magnetic separator Dirt conveyor Radio remote control Plant lighting Feeder under grizzly mesh Refuelling pump Optical belt weigher Rigid head drum dust shroud Winter Powerunit kit Recommended Optional Extras Engine fire extinguisher system Hydraulic water pump assembly for dust suppression system (For pricing please refer to your local dealer) Page 10

11 Dirt Conveyor Conveyor type: Steel troughed tray, hydraulically folding Width: 600mm (23.6 ) Discharge: 2.15m (7 1 ) Drive: Position: Direct drive hydraulic motor Discharge on either side of plant Overband Magnet Magnet type: Terex TX440 Single Pole (S.P.) & Twin Pole (T.P.) available. Suspended, self cleaning with endless belt Belt width: 750mm (30 ) Centres: 1700mm (67 ) Magnet block: S.P. 1050mm x 530mm (41 x 21 ) T.P. 1042mm x 672mm (41 x 26 ) Drive/Control: Direct drive hydraulic motor / Pre-set variable speed Weight: S.P. 975kgs / T.P. 1470kg Feeder Underscreen Mesh Position: Sizes: Replaces standard blanking mat, used in conjunction with optional side conveyor 10,20,30,40,50mm Blowbars 2 full and 2 half martensitic steel Blowbars supplied with the plant as standard. Two further options are available: High Chrome: Ceramic: Suitable for medium to hard rock applications where no steel present in feed material. Good wear characteristics Suitable for applications with limited steel in the feed. Improved wear characteristics over standard martensitic Blowbars Page 11

12 Optical Belt Weigher Optical belt scale, monitors material volume. This is then converted into mass and can be downloaded to a hand held PDA unit via Bluetooth. PDA unit is included in the kit as standard Radio Remote Control Complete with integrated tracking functions and plant stop button. NB - Only available in certain countries where type approval has been obtained Remote can also be used to: Start/Stop feeder Control feeder speed Raise/Lower product conveyor Open top apron Electric Refuelling Pump A 24 volt refuelling pump, allows fuel to be drawn from a remote source. Fuel transfer rate is 50 L/min (13 G/min). Comes complete with all fixtures and fittings Plant Lighting Plant lighting kit available, contains two bidirectional working lamps. Both activated remotely from control panel Page 12

13 Approximate Plant Weights & Dimensions Operating length: 14.2 m (46 7 ) Operating height: 3.42 m (11 2 ) Operating width: 2.56 m (8 5 ) 4.22 m (8 10 ) with side conveyor deployed Transport length: m (47 5 ) Transport height: 3.42 m (11 2 ) Transport width: 2.56 m (8 5 ) Total plant weight: 31,000 kg (68,350 lbs) including dirt conveyor and magnet Colour Plant: RAL 5021 Green; Tracks: RAL 9005 Black Transport Dimensions Page 13

14 Working Dimensions Powerscreen equipment complies with CE requirements. Please consult Powerscreen if you have any other specific requirements in respect of guarding, noise or vibration levels, dust emissions, or any other factors relevant to health and safety measures or environmental protection needs. On receipt of specific requests, we will endeavour to ascertain the need for additional equipment and, if appropriate, quote extra to contract prices. Every endeavour will be made to supply equipment as specified, but we reserve the right, where necessary, to amend the specifications without prior notice as we operate a policy of continual product development. All reasonable steps have been taken to ensure the accuracy of this publication, however due to a policy of continual product development we reserve the right to change specifications without notice. It is the importers responsibility to check that all equipment supplied complies with local legislation regulatory requirements. Plant performance figures given in this brochure are for illustration purposes only and will vary depending upon various factors, including feed material gradings and characteristics. Information relating to capacity or performance contained within this publication is not intended to be, nor will be, legally binding. Terex GB Ltd. 200 Coalisland Road Dungannon Co. Tyrone Northern Ireland BT71 4DR Tel: +44(0) Fax: +44(0) sales@powerscreen.com Web: Terex is a registered trademark of Terex Corporation in the United States of America and many other countries. Powerscreen is a registered trademark of Terex GB Ltd in the United States of America and many other countries. Copyright Terex Corporation Page 14

15 Horizontal Impactor SPECIFICATION - Rev 1. 19/10/09 15