Typical AE Panelboard

Transcription

1 Typical AE Panelboard Installation Consult instructions NEMA PB-1.1 located in the circuit directory on the front door before installing this panelboard. If necessary, order replacement manual from supplier. Wiring Guidelines (Cu or Al) Use 60 C or 75 C ampacity sized wire on line and neutral and equipment ground terminals. Standard wire sizes listed in this publication may be changed by using alternate terminal kits. Refer to circuit breakers for allowable wire temperature rating, wire size and tightening torque. Neutral rated for 200% panelboard phase current option. Use copper wire only at neutral main lugs - 125A (1) neutral cables 250 mcm maximum - 225A (2) neutral cables 250 mcm maximum - 400A (2) neutral cables 600 mcm maximum - 600A (4) neutral cables 50 mcm maximum Suitable for nonlinear loads, 200% rated neutral, additional Y lugs provided for 200% neutral. Short Circuit Current Rating The panelboard s maximum short circuit interrupting rating in rms symmetrical amperes, is equal to the lowest interrupting rating of any device installed, except as noted in the series rating listed in DEH-40007, with integral or remote main circuit breaker or fusible switch installed upstream of the panelboard. Devices to be installed or replacement units shall be from the same manufacturer, of the same type, and have equal or greater interrupting capacity. Maximum continuous loads on main or branch circuits shall not exceed 80% of the ratings of the listed circuit breakers. Branch breaker straps suitable for 0A maximum. Tripped Breaker If the breaker trips, handle will be in intermediate position. Instructions To Restore Power 1. Move handle to OFF position. 2. Then move handle to ON position. Seismic Rating Meets or Exceeds the Requirements According to IEEE High Level with 1.8 Amplication Factor IBC-2006 Sds = 1.g, Ss = 200%, Ip = 1.5, for z/h > 0 Sds = 2.0g, Ss = 00%, Ip = 1.5, for z/h = 0 In accordance with ICC-ES-AC156 Polybag Contents A polybag of goods supplied with every panelboard interior contains: Arc flash label DEH Series Ratings, Wiring Diagrams & Circuit Directory Series rating sticker Front installation instructions ANSI PB1 documentation Circuit numbering stickers (1-84) Front and shield mounting screws

2 Torque Tightening Torque Applies to line, neutral and equipment ground terminal AWG Wire Slotted Screw Min Lbs-Ins Max / Hex Size Internal Hex Min Lbs-Ins Max / / / / / Torque Values for Hardware Screw Size Torque (In-Lbs) #4 Steel 16 #10 Plastic 16 #8 Cu/Al/Steel #10-2 Cu/Al/Steel 2 1/4-20 Al/<.150 Thick Cu 44 1/ Thick Cu 60 5/16- Cu/Al/Steel 110 /8-16 Cu/Al/Steel 220 1/2-1 Cu/Al/Steel 220 Lug Kits Lug Kits for A-Series II Panelboards Rating Pressure Lug Kit Crimp Lug Kit Pressure Lug Kit Wire Range Al/Cu Wire Range Al/Cu Wire Range Cu Only 125A MLA MLT MLR A MLA2 1/0-250 MLT2 2/0-500 MLR2 1/ A Standard - MLA MLT (Cu Only) MLR41 1/0-600 Oversize MLA62 /0-800 (Main) & (Neutral) A Standard -MLA MLR61 1/0-600 Crimp Tools Wire Crimp Tool All Al & Up to 500 MCM Cu Hubbell Anderson VC MCM Cu Hubbell Anderson VC7 Up to # MCM Cu & #5-750 kcmil Al Burndy Tool Y644HS Neutral Lug Z Holes Wire Size Cu / Al Large 2 / 0-14 Small No Arc fault label included with all interiors to be applied by electrical contractor.

3 Interrupting Ratings - Molded Case Circuit Breakers Molded Case Circuit Breakers Federal Spec UL Listed Interrupting Ratings in ka Construction Frame Trip Range (Amps) Pole AC DC Standard Frames Spectra RMS TEY C/B Class W-C-75B RMS Symmetrical AC Volts / Y/ Y/ a , 480Y/ a TJD , b 22 SEH SEL SEP SFH SFL SFP b, 15b a b, 15b a, 22a, 2a a a, 2a b a, 22a b a, 2a a a, 2a SGH , a, 2a SGH , 600 2a SGL , 600 2a SGP , 600 2a SGL , 600 a SGP , a SKH , a, 2a SKL , 600 a SKP , a Poles are not DC rated 2 Not current limiting breaker type Circuit Breaker Terminals (Cu-Al) Standard Frame Current Limiting / High Interrupting Poles No. per Pole TEY - 1,2, 1 Fixed to Breaker Terminal 1 Per Lug Wire Cu-Al (Unless otherwise specified) Range (15-20A) #14-#12 Cu or #12-1 Al, (0-60A) #10-#6 Cu or #8-#4 Al, (70-100A) #4-#1 Cu or#2-1/0 Al - SEH, SEL, SEP 2, 1 TCAL 1 #12-/0 Al; #12-/0 Cu SFHA SFLA, SFPA 2, 1 TCAL129 1 #8-50kcmil TFJ - 2, 1 TCAL,26 1 #4-00MCM TJJ - 2, 1 TCAL4 1 #6-600MCM or 2(2/0-250MCM) SGHA SGL, SGP 2 1 TCLK265-1 TCLK FGN4, FGH4 2, 1 FCALKH - SKHA8 SKLA8, SKPA8 2, 1 2 (2/0-400kcmil, Cu) or 2 (2/0-500kcmil, Al) or #6-600kcmil 2 (2/0-400kcmil, Cu) or 2 (2/0-500kcmil, Al) or #6-600kcmil Top Hole #8-400kcmil Cu or #6-500kcmil Al. Bottom hole #2/0-600kcmil Cu & Al TCAL41 1 #4-600kcmil or 2(1/0-250kcmil) TCAL61 2 2/0-500kcmil TCAL81 /0-500kcmil

4 Wiring Space Wiring Space Typical Panelboard Typical Panelboard Front view with Front trim view with removed trim removed Typical Front w/concealed Hinges and Typical Box Typical Front Typical w/concealed Front w/concealed Hinges Hinges Typical BoxTypical Box Trim Adjusting Screws and Trim Adjusting and Trim Screws Adjusting Screws Surface Surface mounting mounting Surface add mounting add 1/4 1/4 to inside add to inside box 1/4 dimensions to box inside dimensions box dimensions Flush mounting Flush add mounting add 1 1/2 1 1/2 to add inside to 1 inside 1/2 box dimensions to box inside dimensions box dimensions For /8 Bolt For /8 Bolt Box Width (Inside) Box Width (Inside) Box Height (Inside) Box Height (Inside) Minimum Minimum Wiring Wiring Space, Space, From End From of End Lug of to Lug Box to Wall, Box in Wall, Inches in Inches Main Lugs Only, Main to End Lugs Wall Only, to Main Circuit Main Breaker Circuit Breaker Main rating amps End Wall Frame TypeFrame Mounting Phase Lug Phase Lug Neutral Lug Main rating in ampsphase Lug Neutral Lug Mounting Neutral Lug Type To Side Wall To Side (20 Wide Wallbox) To End Wall Phase Lug Neutral Lug To End Wall 125A MLO, 100A Main Breaker 6 6 TEY, SE Horizontal (20" 5Wide box) A 125A MLO, 100A Main Breaker TFJ, SF TEY, SE Vertical Horizontal A 225A SF, SG, FG TFJ, SFVertical Vertical A 400A (1) SG SF, SG, Vertical FG Vertical (1) - 800A 600A (1) SK SG Vertical Vertical To side wall 800A (2) (1) SK Vertical Box width (1) is 0 To side and wall 7.81 deep(2) Box width is 0 and 7.81 deep Wiring Space Wiring Space Branch Branch Circuit Circuit Breakers Breakers Branch Circuit Devices Frame No. of Poles Minimum Wiring Wiring Spaces Spaces To Side Wall To (20 Wide Box) Branch Circuit Devices Frame No. of Poles Double Branched Bolt-on Devices TEY 1,2, Side Wall (20" Wide 6.5" Box) Horizontal Double Subfeeds, Branched Single Branch Bolt-on Mounted, Devices Maximum 6 Poles THQL, THHQL, TED4 THQB, THHQB 2,1,2, 6.5" 5.5" Horizontal Subfeeds, Single Branch Mounted, Maximum Poles SEHA, SELA 2, Horizontal Subfeeds Single Branch Mounted TQD, THQD 2, 5.5" Horizontal Subfeeds, Single Branch Mounted, Maximum 6 Poles SFHA, SFLA 2, 5.5 Enclosures Enclosures Box Suffix 8 8 Box Box Front Front Panel Size Front Suffix (1) Add to base front Panel Size Suffix (1) Panel Size (1) Cat. 7 Size No. Inches 5 (1) Size (2) Size Cat. Inches Inches No. (2)() 6 () Screw Screw cover Screw cover cover C C C catalog number AB25B AB25B AF25F,S 25.5 AF25F,S AF25F,S Front hinged to box D 9 Front hinged Front to box hinged to box D D Consists of two lockable AB1B AB1B AF1F,S 1.5 AF1F,S AF1F,S Yale 5116 Yale 5116 w/rosette Yale 5116 w/rosette Lock Y Lock Y Y doors one over panel AB7B AB7B AF7F,S 7.5 AF7F,S AF7F,S Corbin Corbin Corbin Lock Lock Lock L L L interior and one over AB4B AB4B AF4F,S 4.5 AF4F,S AF4F,S GE 75 GE Key 75 GE Lock Key 75 Lock Key Lock E E E (1) Add to box base wiring (1) front Add gutters. to base front Yale AB49B AB49B AF49F,S 49.5 AF49F,S AF49F,S Corbin Corbin 60 Key Corbin 60 Key Lock 60 LockKey Lock J J J catalog locks number. not catalog available. number AB55B AB55B AF55F,S 55.5 AF55F,S AF55F,S Door within a door 9 P Door within Door a door within (2) a door P (2) P (2) Consists of (2) two Consists lockable doors one able over doors one over of two lock Flush only. Available AB64B AB64B AB64B AF64F,S 64.5 AF64F,S AF64F,S Stainless steel 10 S Stainless steel () S with C N options AB76B AB76B 76.5 AF76F,S Stainless steel () AB76B AF76F,S S AF76F,S 0 wide W panel interior panel and interior and (1) 5 0 wide 0 wide W W B B suffix provides (1) B suffix blank provides blank end end walls. blank walls. Order end Order K walls. suffix Order K suffix for endwalls K suffix for endwalls with for endwalls knockouts. with knockouts. one over box one wiring over box wiring Nameplate N (2) Standard boxes (2) Standard are 20" boxes wide by are 5.81" 20" wide deep. by 5.81" deep. Nameplate Nameplate N N gutters. Yale locks gutters. Yale locks with knockouts. Screw on nameplate U () 6 Flush fronts () are Flush 1 1/2" fronts larger are than 1 1/2" box. larger Surface than fronts box. Surface are 1/4" fronts larger. are 1/4" larger. not available. not available. Screw on nameplate Screw on nameplate U U Standard boxes are 20 wide by 5.81 deep. Metal directory M () Flush only. () Available Flush only. Available 7 Metal directory Metal directory M M Flush fronts are 1 1/2 larger than box. Surface fronts are 1/4 larger. with C and N with options. C and N options. Box Options Box Options Box Options Suffix Cat. (1) No. Suffix (1) Painted Box Painted Box P P Suffix 0" wide (2) 0" wide (2) W W 11 Painted Box P NEMA R/12/4S/4X NEMA R/12/4S/4X or 4 or 4 NEMA 0" wide 4X 12 (16 NEMA Stainless 4X (16 Steel) Stainless 4S Steel) 4S W NEMA R/12/4S/4X or 4 (1) Add to base (1) box Add product to base number. box product number. (2) NEMA Includes RX field (2) Door-in-door Includes installable field gutter installable barrier. gutter barrier. M NEMA 4X (16 Stainless Steel) 4S 11 Permanent Add to base Permanent box Circuit product Number Circuit number. Kits Number Kits 12 Includes field installable gutter Cat. barrier. No APN48 APN48 Permanent Circuit Number Kits APN84 APN APN126 APN APN APN APN126 Front Front Options Front Options Options Stainless Steel Enclosures Stainless Stainless Steel Enclosures Steel Enclosures Dimensions (inches) Cat No. Dimensions Dimensions H (inches) Cat (inches) No. Cat No. D UL Standard CSA Labeled H W H D W UL DStandard UL Standard CSA Labeled CSA Labeled AB254S AB254AS AB254S 6 AB254S AB254AS AB254AS AB254DWS AB254DWAS AB254DWS 8 AB254DWS AB254DWAS AB254DWAS AB14S AB14AS AB14S 6 AB14S AB14AS AB14AS AB14DWS 8 8 AB14DWS AB14DWAS AB14DWS AB14DWAS AB14DWAS AB74S 6 6 AB74S AB74AS AB74S AB74AS AB74AS AB74DWS 8 8 AB74DWS AB74DWAS AB74DWS AB74DWAS AB74DWAS AB44S 6 6 AB44S AB44AS AB44S AB44AS AB44AS AB44DWS 8 8 AB44DWS AB44DWAS AB44DWS AB44DWAS AB44DWAS AB494S 6 6 AB494S AB494AS AB494S AB494AS AB494AS AB494DWS 8 8 AB494DWS AB494DWAS AB494DWS AB494DWAS AB494DWAS AB554S 6 6 AB554S AB554AS AB554S AB554AS AB554AS AB554DWS 8 8 AB554DWS AB554DWAS AB554DWS AB554DWAS AB554DWAS AB644S 6 AB644S 6 AB644AS AB644AS AB644S AB644AS AB644DWS 8 AB644DWS AB644DWAS AB644DWAS AB644DWS AB644DWAS AB764S 6 AB764S AB764AS AB764AS AB764S AB764AS AB764DWS 8 AB764DWS AB764DWAS AB764DWAS AB764DWS AB764DWAS

5 Accessories Field Installed Kits/Replacement Parts Filler Plates Breaker Type THQB/THHQB/THQL THHQL/TEY TQD/THQD/TED4/SE/FB Endwall Kits TQLFP1 TEDFP1 Breaker Mounting Hardware Kits For mounting breaker in existing space Breaker Type TED/THED4/SE TQD/THQD FB Field installed. 1 each, for standard 20 w x 5.81 d boxes. Type Blank Knockout ABEW2 ABEW2 ASPTEDP ASPTQDP ASPFB12P Equipment Grounds AEBG AEIG ASPGIBC AEBGC Item Metal Equipment Ground Aluminum Equipment Ground Copper Equipment Ground Bonded Extruded Bonded Extruded Bonded Extruded Isolated Main Lug Bonded Extruded Bonded Extruded Isolated Insulated Isolated AEIGC Wire Range (1) #6-50MCM (2) #6-250MCM (1) #4-50MCM (1) #6-250MCM 2/0 max. TGL2 EGS12 AEBG AEIG TGL2 TGC2 AEBGC AEIGC ASPGIBC Parts Directory Card Replacement Lock with Std. Key Replacement Lock with GE75 Key Additional Keys for Above Lock Circuit Numbering Strips 1-48 Circuit Numbering Strips Circuit Numbering Strips Adhesive Backed Lamicoid Nameplate /4" x " Metal Directory Card Holder Directory Card Holder Delta Hi-leg Conversion Kit, to Add B-Phase Plug on AL Panels Bolt on AE/AQ Panels NEMA R/12 Tamper Proof Tork Screw Kit 2P to P TQD Conv. Kit 2P to P SF Conv. Kit for horizontal subfeed AD 25 to 65 kaic Barrier kit Service Entrance Kit 2 wire Relay Kit Yale Lock Kit Corbin Lock Kit 2- pole TQD Mechanical Interlock AQ/AL/AE Rail Bracket Front Flush Adjust Kit AE Front Mounting Kit AQ/AL Front Mounting Kit AD Front Mounting Kit Front Hinge to Box Mounting Kit Front Extension Mounting Kit Box Extensions Bolts to box with or without endwall in place. Extensions can be combined to obtain lengths greater than and inches. Box Width and Depth Bonding Kits For Split & Load End Neutral For 225A Horizontal Neutrals 225A Horizontal Neutral To Convert W to 4W 125/225A Horizontal Neutral Conversion from Service Entrance to Non-Service Entrance 125/225A Horizontal Neutral to Convert from Non-Service Entrance to Service Entrance Box Mounting Flush 4L886G16 4L886G1 ASP225HNCP ASPHNCPSENOT 20 x 5.81 Surface ASPHNCPSE Installation & Maintenance Kit Order catalog number PROCARE. Kit includes: (5) filler plate hardware kits (9) bus stud nuts (5) MLA1 filler plates (2) 225A phase barriers (2) feed-thru barriers (1) 400/600A phase barrier (50) directory cards/rating books (50) circuit number strips (1-48) (50) circuit number strips (4-84) (5) standard locks & keys (50) deadfront screws (10) AQ/AE front hardware kits (10) AD front hardware kits (50) service disconnect labels (50) main labels 19C5612P 569B77P1 569B77P2 569B77P5 569B806G1 569B806G2 569B806G 15A7190P1 19C5491G1 19C5491P4 APHBL APHBQ NEMATRX ASP2PTQDP ASP2PTFJP ASP25AD65KA1 ASPSERENT ASP2WRelay ASPYALE47 ASPCORBNTEU1 TQDFM1 ASPAQLEBKT ASPFLUSHADJ 19C5720G 19C5720G6 19C5728G9 19C5700G6 19C5700G11 Flush 0 x 5.81 Surface Flush 0 x 7.81 Surface Box Extension Length (Inches) ABX2509F ABX25F ABX25F ABX2509S ABX25S ABX25S ABX251S ABX257S ABX254S ABX2549S ABX2555S ABX2564S ABX2576S ABX5F ABX5F ABX5S ABX5S ABX7F ABX7F ABX7S ABX7S Box Extension Covers Only 10 covers per kit 9" Covers Surface 9" Covers Flush " Covers Surface " Covers Flush 64" to 76" Covers Surface 64" to 76" Covers Flush ASPABX09S ASPABX09F ASPABXS ASPABXF ASPABX20S ASPABX20F

6 Specifications A-Series Panelboards and branch breakers meet or exceed the following standards and specifications: UL 50 Cabinets and Boxes UL 67 Panelboards UL 489 Circuit Breakers NEMA AB-1 Circuit Breakers NEMA PB-1 and PB-1.1 Panelboards US Federal Spec W-P.115B Panelboards US Federal Spec W-C75b Gen Circuit Breakers Boxes Galvanized steel Blank end walls are standard; knockouts are available when specified Boxes furnished with provisions for ground bus as standard Fronts Finished in ANSI-61 grey polyester powder coat paint. Equipped with corrosion-resistant Valox combination catch and lock door latch (doors over 48 high provided with 2 latches) Equipped with concealed hinges and trim adjusting screws Directory holder permanently mounted to door Panels Dead front construction Interiors are factory assembled on rigid steel frames Metal gages in accordance with UL and NEMA standards Solderless, anti-turn main lugs suitable for copper or aluminium wires are front removable and branch straps are silver-plated copper fully rated at 100 amperes Main bus is aluminum with copper branch connections unless otherwise specified Main disconnect device is identified when supplied, and numbers are provided for branch circuits Interior base assemblies are Noryl and provide breaker mounting and busbar insulation Publications E-DET-465 DE-4 DEH DEH 047 DEH 059 DEH 060 DEH 061 DEH 065 Certification of Seismic Compliance Typical AE Panelboard Technical Information Lighting Panels Rating Labels, Wiring Diagrams and Circuit Directory TED, THED, SED, SHE, SEL, SEP Circuit Breaker Mounting Instructions SGH, SFL, SFP Circuit Breaker Mounting Instructions SGH, SGL, SGP Circuit Breaker Mounting Instructions SKH, SKL, SKP Circuit Breaker Mounting Instructions TQD, THQD Circuit Breaker Mounting Instructions GE 41 Woodford Avenue Plainville, CT Information provided is subject to change without notice. Please verify all details with GE. All values are design or typical values when measured under laboratory conditions, and GE makes no warranty or guarantee, express or implied, that such performance will be obtained under end-use conditions. 2017, General Electric Company and/or its affiliates. All rights reserved DE-4B