ILLUSTRATED PARTS MANUAL 430 MAX 4-WHEEL DRIVE TRACTOR

Transcription

1 ILLUSTRATED PARTS MANUAL 4-WHEEL DRIVE TRACTOR Models: STEINER 27HP KOHLER GAS STEINER 25HP KUBOTA GAS STEINER 2HP KUBOTA DIESEL WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers and should read the entire manual before attempting to set up, operate, adjust or service the machine REV C

2 CALIFORNIA Proposition 65 Warning Diesel engine exhaust and some of its constituents are known to the State of California to cause cancer, birth defects and other reproductive harm. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Californie Proposition 65 Avertissement Les échappements des moteurs diesel et certains de leurs composés sont reconnus par l Etat de Californie pour être cancérigènes, provoquer des défauts congénitaux et d autres dangers en matière de reproduction. AVERTISSEMENT L émission du moteur de ce matériel contient des produits chimiques que l Etat de Californie considère être cancérigènes, provoquer des défauts congénitaux et d autres dangers en matière de reproduction. California Advertencia de la Proposicion 65 El estado de California hace saber que los gases de escape de los motores diesel y algunos de sus componentes producen cáncer, defectos de nacimiento y otros daños en el proceso de reproducción humana. ADVERTENCIA El estado de California hace saber que los gases de escape de este producto contienen productos químicos que producen cáncer, defectos de nacimiento y otros daños en el proceso de reproducción humana. 2003, TEXTRON INC

3 IMPORTANT MESSAGE Thank you for purchasing this Steiner product. You have purchased a world class product, one of the best designed and built anywhere. This machine comes with an Owner / Operator's Manual and an Illustrated Parts Manual. The useful life and good service you receive from this machine depends to a large extent on how well you read and understand these manuals. Treat your machine properly, lubricate and adjust it as instructed, and it will give you many years of reliable service. Your safe use of this Steiner product is one of our prime design objectives. Many safety features are built in, but we also rely on your good sense and care to achieve accident-free operation. For best protection, study the manuals thoroughly. Learn the proper operation of all controls. Observe all safety precautions. Follow all instructions and warnings completely. Do not remove or defeat any safety features. Make sure those who operate this machine are as well informed and careful in its use as you are. See a Steiner dealer for any service or parts needed. Steiner service ensures that you continue to receive the best results possible from Steiner s products. You can trust Steiner replacement parts because they are manufactured with the same high precision and quality as the original parts. Steiner designs and builds its equipment to serve many years in a safe and productive manner. For longest life, use this machine only as directed in the manuals, keep it in good repair and follow safety warnings and instructions. You'll always be glad you did. Jacobsen, a Textron Company One Bob Cat Lane Johnson Creek, WI TABLE OF CONTENTS FIGURES PAGE SAFETY... 2 PARTS SECTION... 3 KOHLER ENGINE ASSEMBLY... FIGURE... 4, 5 KOHLER FUEL SYSTEM & ENGINE CONTROLS... FIGURE , 7 KUBOTA ENGINE ASSEMBLY... FIGURE , 9 KUBOTA COOLING SYSTEM... FIGURE , KUBOTA FUEL SYSTEM... FIGURE , 3 PRIMARY HYDRAULIC SYSTEM... FIGURE , 5 IMPLEMENT HYDRAULIC SYSTEM... FIGURE , 7 SUNDSTRAND SERIES 5 PUMP... FIGURE , 9 SUNDSTRAND SERIES 5 MOTOR... FIGURE , 2 REAR FRAME... FIGURE , 23 FRONT FRAME... FIGURE... 24, 25 FRONT HITCH & PTO... FIGURE , 27 PTO LINKAGE & FRAME-KOHLER... FIGURE , 29 PTO LINKAGE & FRAME-KUBOTA... FIGURE , 3 HOOD & GRILLE... FIGURE , 33 CONTROLS-F/R LEVER... FIGURE , 35 AXLES & WHEELS... FIGURE , 37 PEERLESS TRANSAXLE... FIGURE , 39 ELECTRICAL-KOHLER GAS... FIGURE , 4 ELECTRICAL-KUBOTA GAS... FIGURE , 43 ELECTRICAL-KUBOTA DIESEL... FIGURE , 45 ELECTRICAL-DASH PANEL-AIR COOLED... FIGURE , 47 ELECTRICAL-DASH PANEL-WATER COOLED... FIGURE , 49 DECALS... FIGURE , ROPS BAR WITH SEAT BELT (RB)... FIGURE REAR WEIGHT BAR (WB50)... FIGURE PT HITCH REAR WEIGHT BAR (WB FIGURE FRONT WEIGHT BAR (WB40)... FIGURE PT HITCH HYDRAULICS (PT420)... FIGURE PT HITCH ATTACHMENT PARTS (PT420)... FIGURE DUAL WHEELS (DW00)... FIGURE OPTIONAL HYDRAULIC COOLER... FIGURE SUN SHADE CANOPY (SH)... FIGURE

4 SAFETY NOTICE!!! Unauthorized modifications may present extreme safety hazards to operators and bystanders and could also result in product damage. Jacobsen, a Textron Company strongly warns against, rejects and disclaims any modifications, add-on accessories or product alterations that are not designed, developed, tested and approved by Jacobsen's Engineering Department. Any Jacobsen product that is altered, modified or changed in any manner not specifically authorized after original manufacture including the addition of after-market accessories or component parts not specifically approved by Jacobsen will result in the Jacobsen Warranty being voided. Any and all liability for personal injury and/or property damage caused by any unauthorized modifications, add-on accessories or products not approved by Jacobsen will be considered the responsibility of the individual(s) or company designing and/or making such changes. Jacobsen will vigorously pursue full indemnification and costs from any party responsible for such unauthorized post-manufacture modifications and/or accessories should personal injury and/or property damage result. This symbol means: ATTENTION! BECOME ALERT! Your safety and the safety of others is involved. Signal word definitions: The signal words below are used to identify levels of hazard seriousness. These words appear in this manual and on the safety labels attached to Jacobsen machines. For your safety and the safety of others, read and follow the information given with these signal words and/or the symbol shown above. DANGER indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. WARNING indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices or property damage. CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. MODEL NUMBER: This number appears on sales literature, technical manuals and price lists. SERIAL NUMBER: This number appears only on your mower. It contains the model number followed consecutively by the serial number. Use this number when ordering parts or seeking warranty information. 2

5 PARTS SECTION PARTS SECTION 3

6 KOHLER ENGINE ASSEMBLY FIGURE 4

7 KOHLER ENGINE ASSEMBLY FIGURE ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY ENGINE-KOHLER CH25 * ELEMENT-AIR CLEANER * ELEMENT-PRECLEANER * OIL FILTER SHAFT-DRIVE -3 A0305 BOLT-M8-.25X W0305 KEY-WOODRUFF 3/6x5/ PLATE-ADAPTER BOLT, 5/6x-/ BK60H PULLEY-6" H8 BUSHING-H / KEY-SQUARE /4x/4x-/ BELT GUARD BOLT, 7/6x VALVE, OIL DRAIN HOSE, /2" PUSH LOCK, 8" MUFFLER, KOHLER LOCKWASHER, 8MM BOLT-MET M8-.25x SHIELD-FRONT ENGINE -8 * TRIM-LOC, 4" LOCKWASHER, 5/6" K72 BOLT, 5/6x-/2 GR NUT-FLANGE, 5/6" LOCKWASHER, 7/6" WASHER-FLAT, 5/6" NIPPLE, 3/8 NPT x COUPLING, 3/8 NPT * NOT ILLUSTRATED 5

8 KOHLER FUEL SYSTEM & ENGINE CONTROLS FIGURE 2 6

9 KOHLER FUEL SYSTEM & ENGINE CONTROLS FIGURE 2 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY LINKAGE-THROTTE LEVER-THROTTLE NUT-FLANGE, / MOUNT-THROTTLE CABLE (INCLUDES ITEM 5) BOLT-MET M5-0.80x CABLE-THROTTLE X ROD END, /4x SA ROD END, /4x0-32 STUD BOLT, /4x-3/ SC04 SET COLLAR, / NUT, /4" E50 LOCKNUT-NYLON # GROMMET /6x-5/ TRIM SEAL, 35" LENGTH SHIELD-HEAT 2-6 Q7475 WEATHERSTRIP /2X2x BOLT-FLANGE, /4x3/ VALVE-FUEL W/O SCREEN N CLAMP, HOSE FUEL LINE, /4"x3" FUEL FILTER FUEL LINE, /4"x54" * NOT ILLUSTRATED 7

10 KUBOTA ENGINE ASSEMBLY FIGURE 3 8

11 KUBOTA ENGINE ASSEMBLY FIGURE 3 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY AIR CLEANER ASSY (INCLUDES ITEMS 2 & 3) PLATE, ADAPTER 3-BOLT (INCLUDES ITEMS 40-44) END CAP, AIR CLNR ELEMENT, AIR FLTR HOSE-AIR INTAKE TUBE-AIR INTAKE CLAMP-HOSE 2-/2" CLAMP-MUFFLER EXT PIPE-MUFFLER EXT MUFFLER-KUBOTA 3 BOLT BRACKET-MUFFLER GASKET-MUFFLER NUT-HEX 5/ BOLT-HEX 5/6-8x-/ BOLT-HEX 3/8-6x LOCKWASHER, SPRING SHEAVE-PTO VALVE-OIL DRAIN SENDER-TACHOMETER B27 WASHER-BEADED, 5/6" DISC-WEASLER BOLT, 5/6-24x-/ COUPLER FLANGE LOCKNUT-NYLON 5/ KEY-3/6X3/6X-/4 SQ BLT-METRIC, M8-.25x SHAFT, PUMP DRIVE GUARD-FLYWHEEL W0305 KEY-WOODRUFF 3/6x5/ COUPLER ASSEMBLY (INCLUDES ITEMS 3-35) 3-30 * 87-3 COUPLER DISC 3-3 * 87-2 COUPLER FLANGE * BOLT-5/6-24x-/ * LOCKNUT-NYLON 5/ * 99-B27 WASHER-BEADED, 5/6" * BOLT-HEX 5/6-8x * BOLT-HEX 5/6-8x * BOLT-HEX 5/6-8x3/ * 99-9 BOLT-SHCS 5/6-8x3/ * LOCKWASHER-HEL 5/ ENG-KUBOTA DIESEL D ENG-KUBOTA GAS WG752 * OIL FILTER * -048 CLAMP-INSULATED HALF * FAN * FAN BELT * ALTERNATOR * 3-RP REGULATOR * SNDR-WTR TMP (GAS) * SNDR-WTR TMP (DIESEL) * KIT-BLOCK HEATER * REPLACEMENT CORD * GLOW PLUG 3 (USED ON DIESEL ENGINES ONLY) * FUEL INJECTOR 3 (USED ON DIESEL ENGINES ONLY) * SPARK PLUG 3 (USED ON GAS ENGINES ONLY) * 3-EG CARBURETOR (USED ON GAS ENGINES ONLY) * NOT ILLUSTRATED HOSE, AIR INTAKE CLAMP, SHEILDED HOSE (ITEMS 36 & 37 USED ON GAS ENGINES ONLY) HOSE, AIR INTAKE (ITEM 38 USED ON DIESEL ENGINES ONLY) 9

12 KUBOTA COOLING SYSTEM FIGURE 4 0

13 KUBOTA COOLING SYSTEM FIGURE 4 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY BOLT-WLF /4-20X3/ RADIATOR SCREEN ASSY BAFFLE, LEFT RADIATOR BAFFLE, RIGHT RADIATOR MOUNT, LEFT RADIATOR COOLANT REC. BOTTLE BOLT-METRIC M6-.00X BRKT, UPPER RADIATOR BRKT, LH RAD SCRN MTG RADIATOR CAP NUT-HEX, 3/ WASHER,.8X.406X6GA BOLT-HEX 3/8-6X-/ MOUNT, RIGHT RADIATOR BUSHING-UPPER WASHER-CUPPED BOLT-RADIATOR MNT HOSE-LOWER RADIATOR HOSE-UPPER BRKT, RH RAD SCRN MTG 4-22 SHROUD-RADIATOR (AVAILABLE FROM KUBOTA DEALER) BRACKET, COOLANT TANK CLAMP, HOSE 4-/4" DIA BOLT-5/6-8X3/4 WLF NUT, 5/ TUBING, /4" VACUUM, 2" SNAP PIN PIPE BAND BUSHING-LOWER 2

14 KUBOTA FUEL SYSTEM FIGURE 5 2

15 KUBOTA FUEL SYSTEM FIGURE 5 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY FUEL LINE, 5/6"x49" FUEL LINE, 5/6"x37" RETURN LINE, /4"x72" FITTING-90 ELBOW CAP-2" PIPE, W/DRAIN N CLAMP, HOSE PUMP-ELECTRIC DSL BRKT, DIESEL FUEL FILTER FUEL FILTER ASSY 5-0 * ELEMENT-FUEL FLTR BOLT-HEX 5/6-8x2-/ BOLT-5/6-8x3/4 WLF NUT, 5/ TUBE-DRAIN, VINYL /4x0 (ITEMS -4 USED ON DIESEL ENGINE ONLY) VALVE-FUEL, W/O SCREEN (QTY 2 USED ON DIESEL ENGINE) (QTY USED ON GAS ENGINE) FUEL LINE, 5/6"x2" FILTER-FUEL CLAMP-HOSE 5/8" (QTY 7 USED ON DIESEL ENGINE) (QTY 5 USED ON GAS ENGINE) PUMP-ELECTRIC GAS CAP-2" PIPE PLUG-PIPE, /8" FUEL LINE, 5/6"x57" (ITEMS 5-22 USED ON GAS ENGINE ONLY) * NOT ILLUSTRATED 3

16 PRIMARY HYDRAULIC SYSTEM FIGURE 6 4

17 PRIMARY HYDRAULIC SYSTEM FIGURE 6 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY DIPSTICK, REAR AXLE 2" T-6-6 FITTING, TEE NIPPLE, 3/8 CLOSE FITING, HOSE, PUSH LOCK /2"x59" FITTING, HOSE, PUSH LOCK /2"x52" FITTING, FITTING, HYDRAULIC MOTOR 2 6- * GASKET-HYD MOTOR TUBE-/8" NPT VALVE, INLINE SHUT OFF PIPE CAP, 3/8 NPT STEEL NIPPLE (3/8 X 6) T-6-6 FITTING, TEE CP-0 FITTING, PLUG HOSE, /2"x44" LL/4-8 FITTING, FITTING, FILTER HEAD, O-RING FILTER, HYDRAULIC PIPE PLUG, VENTED FITTING, AXLE PORT HOSE, VACUUM, 2" (ITEM 25 USED ON UNITS WITH KUBOTA ENGINES ONLY) TUBING, /4" VACUUM, 9" (ITEM 26 USED ON UNITS WITH KOHLER ENGINES ONLY) TRANSAXLE, -/4" AXLES * 5-02 OIL-HYDRAULIC, QUART 6-29 * OIL-HYDRAULIC, 4.5 GAL * 5-05 OIL-HYDRAULIC, 55 GAL SLEEVING, ID.53 NYLON 6-32 * WASHER-.56XX2GA HOSE, PSHLCK 3/4x43-/2" HOSE-VENT TRANS TUBE, STEEL HYD (ITEMS 34 & 35 USED ON KOHLER ENGINES ONLY) HOSE-VENT TRANS TUBE, STEEL HYD (ITEMS 36 & 37 USED ON KUBOTA ENGINES ONLY) FITTING PUMP-SUNDSTRAND (INCLUDES ITEMS 43-45) 6-43 * 99-5 BOLT, /2-20 X -3/4 SHCS * NUT,/2-20 NF * LOCKWSHR-HELICAL / HOSE, /2"x27" 00R HOSE, /2"x64" 00R FITTING-STR * NOT ILLUSTRATED 5

18 IMPLEMENT HYDRAULIC SYSTEM FIGURE 7 6

19 IMPLEMENT HYDRAULIC SYSTEM FIGURE 7 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY HOSE, /4 X 20 (USED ON KOHLER ENGINES) VALVE-2 SPOOL 7-3 * DETENT KIT FOR * DETENT-SPOOL, * SEAL KIT FOR * A CLIP & PIN FOR HANDLES HANDLE FITTING T-6-6 FITTING CP-6 FITTING-CAP E NUT-STEERING VALVE VALVE-STEERING, 5 PORT 7-3 * FITTING 7-4 * 2-SK0000 SEAL KIT-STEERING VLV 7-5 * OUTER SEAL-STEERING 7-6 * FACE SEAL-STEERING VLV 7-7 * BUSHING-STEERING VLV 7-8 * x SPRING KIT-STEERING HOSE SPACER-STEERING CYL A ROD END-5/8 STEEL CYLINDER-STEERING, ROD END, / HOSE-/4 X FITTING HOSE-/4 X CYLINDER- 2-/4 X 5 HYDR 7-28 * 2-375X SEAL KIT FOR FITTING HOSE-3/8 X QUICK COUPLER-FEMALE * DUST COVER FOR SPACER-STEERING CYL T-6-6 FITTING-TEE LOCKWASHER-5/ A0NF LOCKNUT-5/8 NF A08NF LOCKNUT-/2 NF LOCKWASHER-/ FLAT WASHER-/ BOLT-/2 X 2-/2 NF HOSE-3/8 X BOLT-5/8 X 3-/2 NF E52 JAM NUT-5/ HOSE-/4 X 3 (ITEM 44 USED ON KOHLER ENGINES) HOSE, /4 X R (ITEM 45 USED ON KUBOTA ENGINES) BRACKET-COUPLER FITTING-STRAIGHT HOSE, /4 X FITTING PUMP-SUNSTRAND BRACKET-AUX VALVE (ITEM 5 USED ON UNITS WITH KOHLER ENGINES ONLY) BRACKET-AUX VALVE (ITEM 52 USED ON UNITS WITH KUBOTA ENGINES ONLY) FITTING HOSE, /4 X 7 (USED ON KUBOTA ENGINES) * NOT ILLUSTRATED 7

20 SUNDSTRAND SERIES 5 PUMP FIGURE

21 SUNDSTRAND SERIES 5 PUMP FIGURE 8 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY DRIVE PIN GEROTOR, CHARGE PUMP SHAFT-PUMP BEARING HOUSING-PUMP RING-RETAINING (ITEMS -6 USED ON SERIES 5-277) GEROTOR ASSEMBLY SHAFT-PUMP BEARING HOUSING ASSEMBLY RING-RETAINING (ITEMS 7- USED ON SERIES ) BEARING-CHARGE PUMP SEAL-INPUT SHAFT SCREW-HEX 5/6x7/ HOUSING-CHARGE PUMP O-RING SEAL-CONTROL SHAFT WASHER RING-RETAINER KIT-VALVE IMPLEMENT RLF (INCLUDES ITEMS 2 & 22) SPRING-IMPLEMENT RLF SHIM PACK KIT-CHECK VALVE END CAP-PUMP PIN-LOCATING BEARING-NEEDLE PLATE-VALVE PUMP RING-RETAINING KIT-CYLINDER BLOCK (INCLUDES ITEMS 30 & 45) WASHER-PISTON RETAIN PLATE-THRUST SPRING PIN SWASHPLATE-VARIABLE SHAFT-TRUNNION BEARING-BRONZE SHAFT-CONTROL GASKET O-RING RING-RETAINING KIT-RELIEF VALVE PRIOR O-RING BACKUP RING BYPASS VALVE BOLT-HEX 3/8-6X2-/ PISTON ASSEMBLY * TOOL-SPRING COMPRESS (USED TO SERVICE ITEM 29) * NOT ILLUSTRATED 9

22 SUNDSTRAND SERIES 5 MOTOR FIGURE

23 SUNDSTRAND SERIES 5 MOTOR FIGURE 9 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY PLATE-VALVE MOTOR RING-RETAINING KIT-CYLINDER BLOCK (INCLUDES ITEMS 4 & 5) PISTON ASSEMBLY WASHER-PISTON RETAIN NUT-3/8-6 HEX F3053 WASHER-FLAT 3/8x3/4x END CAP-MOTOR PIN-LOCATING GASKET BEARING-NEEDLE PLATE-THRUST HOUSING-MOTOR (ITEM 3 IS NOT AVAILABLE AS A SERVICE PART) BEARING RING-RETAINING WASHER-PRESSURE BOLT-3/8x3-/4, GRADE SHAFT-MOTOR 9-9 * 5-0 PINION GEAR 9-20 * SNAP RING 5/8 9-2 * TOOL-SPRING COMPRESS (USED TO SERVICE ITEM 3) * NOT ILLUSTRATED 2

24 REAR FRAME FIGURE 0 22

25 REAR FRAME FIGURE 0 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY FUEL TANK CAP, GAS TANK GASKET, LEVEL SENDER SENDER, FUEL LEVEL SCREW, MACHINE 0-32x LOCKWASHER WASHER-.50x.203x8GA NUT-HEX #8-32 KEPS CP0508 COTTER PIN, 5/32 X ZP BLT-HEX 3/8-6X-/ NUT, 5/ SCREW, 2-24x/2 HEX TWO BULB TAIL LIGHT 2 (INCLUDES ITEM 44) SEAT, XR-20 STEINER 0-5 * KIT-SUSPENSION SEAT- 0-6 * SWITCH, SEAT N.O. 0-7 *99-K3 BOLT, FLANGE /4-20x/ * WIRE ASSY, SEAT SWITCH 0-9 * ARMREST, RH 0-20 * ARMREST, LH BLT-WLF 5/6-8X/ * ADJUSTER, LATCHING 0-23 * ADJUSTER, SLAVE 0-24 *99-23 BOLT, 5/6-8x/2 NC SHCS WLDMT-SEAT PLATE ISOLATOR,RUBBER WASHER-.8X.406X6GA REAR FENDER, LEFT REAR FENDER, RIGHT BOLT-WLF /4-20X3/ NUT-WLF / FLATWASHER-/ LOCKWASHER-/4 HEL GUARD, REAR TRANSAXLE BOLT-WLF 3/8-6x3/ NUT-WLF 3/ FRONT FENDER, LEFT FRONT FENDER, RIGHT BOLT-HEX /4-20X3/ REAR FRAME-TREADPLT WASHER, 3/8 HELICAL LCK NUT-3/8-6 HEX TOE GUARD *33-04 BULB-TAIL LIGHT REAR MOTOR SHIELD CENTER LINK BLT-HEX 5/8-8X2-/ LOCKWSHR-HELICAL 5/ NUT-HEX 5/8-8 CNTRLCK REFLECTOR, AMBER OVAL SCREW #8-32X3/ LOCKNUT-NYLON / FENDER LID TRIM-LOC, 6" 2 (ITEMS 53 & 54 USED ON UNITS WITH KOHLER ENGINES ONLY) BATTERY LID TRIM-LOC, 26" RUBBER LATCH ASSEMBLY POP RIVET, 3/6 X /4 SS BRACKET, HOLD-DOWN 2 (ITEMS USED ON UNITS WITH KUBOTA ENGINES ONLY) CLAMP, /2" INS. HALF PIPE CAP, 2" W/DRAIN (ITEM 6 USED ON UNITS WITH DIESEL ENGINES ONLY) PIPE CAP, 2" (ITEM 62 USED ON UNITS WITH GAS ENGINES ONLY) * NOT ILLUSTRATED 23

26 FRONT FRAME FIGURE 24

27 FRONT FRAME FIGURE ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY FRAME, FRONT STEERING WHEEL -3 *47-04 CAP, STEERING WHEEL -4 * LABEL-STEERING STEINER PUMP ACCESS PANEL BOLT-WLF /4-20X3/ THROTTLE LINKAGE WSHR.50X.203X8GA LOCKNUT-NYLON # NUT-WLF 3/ F39 U-BOLT, 3/8-6 X 2" CUT SHAFT, CYLINDER MOUNT CP050 COTTER PIN, 5/32 X -/ CYLINDER, 2-/4" X 5" HYD WSHR.05X.500X4GA BOLT-5/6-8X3/4 WLF NUT, 5/ LEVER, THROTTLE KNOB, TAPERED 3/ WASHER, FRICTION /64X5/8X6GA WASHER SPRING,COMP X LOCKNUT-NYLON 5/ BATTERY TRAY BATTERY SUPPORT BLT-WLF 5/6-8X/ K02 BOLT, FLANGE 5/6-8 X DASH PANEL BOLT, 5/6-8X3/4 HEX -30 *47-0 CABLE, CHOKE 3-/2" (ITEM 30 USED ON UNITS WITH KOHLER ENGINES ONLY) -3 * CABLE, CHOKE 33-/2" (ITEM 3 USED ON UNITS WITH KUBOTA ENGINES ONLY) -32 S800 STRAP,5"-URETHANE -33 G8084 QUICK LINK, 3/ K38 CAP SCREW FLATWASHER, / NUT-WLF / LOCKNUT-NYLON / TRIM, TRIM-LOC 5" TRIM, TRIM-LOC 8" (ITEMS 38 & 39 USED ON UNITS WITH KOHLER ENGINES ONLY) BRKT-COUPLER BRKT-AUX VALVE (ITEM 4 USED ON UNITS WITH KOHLER ENGINES ONLY) BRKT-AUX VALVE (ITEM 42 USED ON UNITS WITH KUBOTA ENGINES ONLY) * NOT ILLUSTRATED 25

28 FRONT HITCH & PTO FIGURE 2 26

29 FRONT HITCH & PTO FIGURE 2 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY FRAME, FRONT ARM, IDLER SLIDER BRKT LOCKNUT-NYLON 3/ LOCKNUT, /2-3 NYLON SHIELD, DOUBLE IDLER WASHER-.56XX2GA PULLEY, 2GR IDLER * 83-MK73 BUSHING, FOR * BEARING, FOR BOLT,/2-3 X 3-/4 NC B039 BELT, B A040 BELT, SPRING RP224 ROLL PIN, 3/8 X SPRING,TORSION PTO IDLER BRACKET ADJ IDLER LOCK CLEVIS PIN, 5/8 X 2.3/ FRONT LIFT, LEVER, FRONT LIFT REL KNOB, LARGE (ITEMS 8 & 9 USED ON UNITS WITH KOHLER ENGINES ONLY) LEVER, FRONT RELEASE KNOB, SMALL (ITEMS 20 & 2 USED ON UNITS WITH KUBOTA ENGINES ONLY) FRAME, LOWER FRONT BOLT-HEX /2-3X-/ LOCKWSHR-HELICAL / COTTER PIN-/8X BOLT, 3/8-6X2-3/4 HEX * NOT ILLUSTRATED 27

30 PTO LINKAGE & FRAME-KOHLER FIGURE 3 28

31 PTO LINKAGE & FRAME-KOHLER FIGURE 3 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY FRAME, FRONT PTO SWITCH MTG BRKT BOLT-WLF /4-20X3/ NUT-WLF / KNOB, TAPERED 3/ LEVER, PTO WSHR.8X.406X6GA SPRING COTTER PIN-/8X LINKAGE, PTO SPRING ARM, IDLER BELT GUARD BOLT-HEX 3/8-6X IDLER BRACKET, BELT GUARD WASHER, 3/8 HELICAL LCK LOCKNUT-NYLON 3/ SUPPORT, FRONT BOLT-HEX /4-20X3/ NUT-/4-20 HEX BLT-WLF 3/8-6X3/ NUT-WLF 3/ BLT-HEX 7/6-4X LCKWSHER-HELICAL 7/6 2 *NOT ILLUSTRATED 29

32 PTO LINKAGE & FRAME-KUBOTA FIGURE 4 30

33 FIGURE 4 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY COMPRESSION SPRING WSHR.8X.406X6GA BOLT-HEX 3/8-6X-/ BRACKET, BELT GUIDE BLT-HEX 3/8-6X-/ NUT-WLF 3/ HEX BOLT M0X LOCKWASHER,0MM MOTOR ISOLATOR NUT, 5/ ENGINE MOUNT FRAME, ENGINE MOUNT S ROD END NUT-HEX / BOLT-5/6-8X3/4 WLF COTTER PIN-/8X THROTTLE ADAPTER LINK, THROTTLE (ITEM 8 USED ON UNITS WITH GAS ENGINES ONLY) PTO SWITCH MTG BRKT KNOB, TAPERED BRACKET, FILTER MOUNT LEVER, KUBOTA PTO LINK, KUBOTA PTO SPRING SC06 S/B SET COLLAR, 3/8" ZP LINK, PIVOT KUBOTA PTO BLT-HEX 3/8-6X IDLER BOLT-HEX 3/8-6X2-/ LOCKNUT-NYLON 3/ IDLER ARM, PTO BOLT-WLF 3/8-6X WASHER, 3/8 HELICAL LCK B0 WASHER,/8x3/32x-/ B40 WASHER, 3/8"X"X LINKAGE, THROTTLE KUBOTA MODULE MOUNT LINKAGE, SHUT-OFF (ITEMS USED ON UNITS WITH DIESEL ENGINES ONLY) PTO LINKAGE & FRAME-KUBOTA 3

34 HOOD & GRILLE FIGURE 5 32

35 HOOD & GRILLE FIGURE 5 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY HOOD BOLT-HEX /4-20X FLATWASHER, / HEADLIGHT *33-08 BULB-REPLACEMENT HOOD HINGE, LEFT LOCKWASHER-/4 HELICAL NUT-/4-20 HEX B2 SPACER BOLT-WLF /4-20X3/ NUT-WLF / HOOD HINGE, RIGHT GRILLE, HATCH TRIM, TRIM-LOC 36" WEATHERSTRIP 2" NUT-WLF / CLAMP-INSULATED HALF HOOD FILLER PLATE BLT-WLF /4-20X/2 2 (ITEMS 6-9 USED ON UNITS WITH KOHLER ENGINES ONLY) SIDE PANEL GRILLE, HOUSING LABEL * GRILLE SPACER K27 BOLT, FLANGE /4-20x (ITEMS USED ON UNITS WITH KUBOTA ENGINES ONLY) LABEL- HOOD, RH 5-26 *42843 LABEL- HOOD, LH DECAL-HANDS/BELT * NOT ILLUSTRATED 33

36 CONTROLS-F/R LEVER FIGURE 6 34

37 CONTROLS-F/R LEVER FIGURE 6 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY FRAME, FRONT WASHER, FRICTION WASHER, 3/32IDx-9/32OD BOLT-HEX 3/8-6X-3/ LOCKWASHER-/4 HELICAL NUT-HEX / WSHR-FLAT.265x.625x HUB, PUMP LEVER NUT, 5/ SPRING, COMPRESSION GROMMET, /4 ID X 5/8 OD BLT-HEX 3/8-6X MA ROD END, /4" MALE S ROD END NUT-3/8-6 HEX K7 BOLT, FULL THREAD 3/8x3" SPRING, HANDLE KNOB, LARGE HANDLE-FORWARD/REV NUT-HEX # WASHER, LOCK # SWITCH, 3 POST NUT-WLF 3/ PUMP LEVER WSHR, 3/8 HELICAL LOCK NUT-/4-20 HEX BOLT-HEX /4-20X BOLT, /4-20X-/2 HEX SCREW-MACHINE#4-40x3/ NUT-HEX JAM,3/ MOUNT, STABILIZER STABILIZER, SHOCK K62 BOLT-FLNG 5/6-8x-/ BOLT,/4-20 X -3/4 NC BLT-HEX 5/6-8X2-/ K77 BOLT, SOCKET /4x5/ MOUNT, HANDLE NUT-WLF / MOUNT, F-R HANDLE LOCKNUT-NYLON 3/ /64X5/8X6GA WASHER WSHR.8X.406X6GA NUT, HEX 2 35

38 AXLES & WHEELS FIGURE 7 36

39 AXLES & WHEELS FIGURE 7 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY WHEEL ASSY, 2X00X8 2 TRACTION BAR TIRE (INCLUDES ITEMS 3 & 4) WHEEL ASSY, 2X00X8 2 TRACTION BAR TIRE (INCLUDES ITEMS 3 & 4) 7-3 * TIRE-TRACTION BAR TYPE 7-4 * RIM-8x * TIRE-TURFMATE (ITEM 5 IS AN OPTIONAL TIRE) SEAL-AXLE SHAFT -/4" /4X/4X-/4 MACH KEY P20 BUSHING, -/ HUB BOLT, /2-20X2 HEX WHEEL NUT / TRANSAXLE, -/4 AXLES KNOB, TAPERED 3/ TRANSAXLE SHIFTER FRT HANDLE GRIP, 3/8 IDx3/ SHIFT LEVER BRACKET TRANSAXLE SHIFTER RR BOLT-HEX /4-20X3/ BRAKE PADS, (2) KEY WOODRUFF.9X.75 # DISC, PARKING BRAKE BRAKE, CALIPER CMPLT LEVER ASSY, BRAKE BRAKE LINK BOLT-HEX 3/8-6X-/ TWO LEVER SHFTR BRKT BOLT-WLF /4-20X3/ NUT-WLF / WSHR-FLAT.265x625x LOCKNUT-NYLON / SHIFTER LOCK STRAP BRAKE LEVER *NOT ILLUSTRATED 37

40 PEERLESS TRANSAXLE FIGURE 8 38

41 PEERLESS TRANSAXLE FIGURE 8 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY B TRANSAXLE CASE (INCLUDES ITEMS 2-5) NEEDLE BEARING NEEDLE BEARING NEEDLE BEARING NEEDLE BEARING TRANSAXLE COVER (INCLUDES ITEMS 3-5) RING GEAR SIDE GEAR PINION GEAR CORE BODY DIFFERENTIAL CARRIER DIFFERENTIAL CARRIER AXLE, 8-7/32" LONG SNAP RING DIFFERENTIAL BOLT LOCKWASHER, 3/8" THRUST WASHER COUNTER SHAFT BRAKE SHAFT A OUTPUT PINION BEVEL GEAR, 30 TEETH SPUR GEAR, 6 TEETH SPUR GEAR, 23 TEETH CLUSTER GEAR, 20/27 TTH AXLE, 6-7/32" LONG OUTPUT GEAR, 37 TEETH SPACER THRUST WASHER, TAB SHIFTER FORK A SHIFTER ROD GASKET-CASE & COVER SPACER PLUG-PIPE SNAP RING PIN-DOWEL DETENT SPRING SEAL-OIL (788008) DRAIN PLUG, MAGNETIC THRUST WASHER, TAB THRUST BEARING SEAL-OIL (788034) BEARING, AXLE THRUST BEARING O-RING (788048) BOLT-HEX /2-3X2-3/ LOCKWASHER, /2" SCREW, 5/6x" DETENT SET SCREW DETENT BALL SEAL, AXLE PINION GEAR (778093A) AXLE HOUSING, LEFT AXLE HOUSING, RIGHT BOLT, /2x2-3/4" SHCS 4 (ITEM 54 USED ON LEFT SIDE) GASKET, MOTOR (788050) BOLT, /2 UNCx-3/ BOLT, /2x-/2" SHCS 4 (ITEM 57 USED ON RIGHT SIDE) THRUST WASHER 2 39

42 ELECTRICAL-KOHLER GAS FIGURE 9 40

43 ELECTRICAL-KOHLER GAS ITEM PART NO * * * FIGURE 9 DESCRIPTION QTY TAILLIGHT, RED BATTERY CABLE, 4 GA 30" COVER-TERMINAL, NEG. BATTERY, 26/26R 550 CCA BATTERY CABLE, 4 GA 4" COVER-TERMINAL, POS. SLEEVING, ID 0.77 NYLON SWITCH-NEUTRAL START CIRCUIT BREAKER 2 ITEM PART NO * 9-2 * 9-3 * DESCRIPTION QTY IGNITION SWITCH, KOHLER KEY, MOLDED HARDWARE SET CONNECTOR-SOCKET RELAY 2 HEADLIGHT 2 WIRE HARNESS, KOHLER SWITCH, PTO SENDER, FUEL LEVEL SWITCH-SEAT N.O. STRAP, BRAIDED GROUND * NOT ILLUSTRATED 4

44 ELECTRICAL-KUBOTA GAS FIGURE 20 42

45 ELECTRICAL-KUBOTA GAS ITEM PART NO * * FIGURE 20 DESCRIPTION QTY TAILLIGHT, RED BATTERY CABLE, 89" COVER-TERMINAL, NEG. BATTERY, 26/26R 550 CCA BATTERY CABLE, 89" COVER-TERMINAL, POS. SENDER-MAGNETIC, TACH SWITCH-NEUTRAL START CIRCUIT BREAKER 2 ITEM PART NO. DESCRIPTION QTY * SWITCH, IGNITION KEY, IGNITION STRAP, BRAIDED GROUND HEADLIGHT RELAY SENDER, FUEL LEVEL WIRE HARNESS, KUB GAS SWITCH, PTO SWITCH-SEAT N.O. 2 2 * NOT ILLUSTRATED 43

46 ELECTRICAL-KUBOTA DIESEL FIGURE 2 44

47 ELECTRICAL-KUBOTA DIESEL FIGURE 2 ITEM PART NO. DESCRIPTION QTY * * * TAILLIGHT, RED BATTERY CABLE, 89" COVER-TERMINAL, NEG BATTERY, 26/26R 550 CCA BATTERY CABLE, 89" COVER-TERMINAL, POS SENDER-MAGNETIC, TACH SWITCH-NEUTRAL START CIRCUIT BREAKER SWITCH, IGNITION KEY, IGNITION 2 ITEM PART NO DESCRIPTION QTY STRAP, BRAIDED GROUND HEADLIGHT RELAY SENDER, FUEL LEVEL WIRE HARNESS, KUB DSL SWITCH, PTO SWITCH-SEAT N.O. MODULE-FUEL SHUT OFF SOLENOID-STOP 2 2 * NOT ILLUSTRATED 45

48 ELECTRICAL-DASH PANEL-AIR COOLED FIGURE 22 46

49 ELECTRICAL-DASH PANEL-AIR COOLED FIGURE 22 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 22- * INSTRMNT PNL, AIR COOL (ITEM INCLUDES ITEMS 2-9) GAUGE-FUEL, GAUGE-TACHOMETER, SWITCH, ROCKER ON/OFF WIRE HARNESS-PNL LIGHT-ASSY MODULE GAUGE-VOLT METER, HOLE PLUG-GAUGE COVER-INSTRMNT PNL * NOT ILLUSTRATED 47

50 ELECTRICAL-DASH PANEL-WATER COOLED FIGURE 23 48

51 ELECTRICAL-DASH PANEL-WATER COOLED FIGURE 23 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 23- * 35-2 INSTRMNT PNL, WTR COOL (ITEM INCLUDES ITEMS 2-9) GAUGE-FUEL, GAUGE-TACHOMETER, SWITCH, ROCKER ON/OFF WIRE HARNESS-PNL LIGHT-ASSY MODULE GAUGE-VOLT METER, GAUGE-WATER TEMP COVER-INSTRMNT PNL * NOT ILLUSTRATED 49

52 DECALS FIGURE DRIVE WHEEL 2 IMPORTANT TIRE SPECIFICATIONS SINGLE TIRES: Inflate 5 to 8 lbs. pressure DUAL WHEELS: INNER TIRE: Inflate to 6 lbs. pressure OUTER TIRE: Inflate to 3 lbs. pressure INFLATE WITH AIR ONLY LIQUID IN TIRES VOIDS WARRANTY On Rough Terrain... Reduce speed and exercise caution. IMPORTANT By Jacobsen 20 8 By Jacobsen 2 By Jacobsen 2 N CAUTION SHIFT BOTH TRANSAXLES INTO THE SAME RANGE OR SERIOUS MECHANICAL DAMAGE WILL RESULT TRANSAXLE VENT OPEN VENT CLOSED CAUTION DO NOT TOW! Serious damage to hydraulic system will result. For emergency moving stalled unit, see Operator's Manual. SLOW DOWN ON ROUGH, UNEVEN OR STEEP TERRAIN. WARNING KEEP HANDS AWAY FROM BELT WHILE ENGINE IS RUNNING. WARNING BEFORE OPERATING THIS MACHINE READ AND UNDERSTAND THE OPERATOR'S MANUAL. KEEP ALL SHIELDS IN PLACE AND FOLLOW ALL SAFETY RULES D G P FILL WITH STEINER/TRC TORQUE FLUID ONLY USE OF OTHER OILS WILL VOID WARRANTY AND MAY DAMAGE SYSTEM. 2 N

53 DECALS FIGURE 24 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY LABEL-4 WHEEL DRIVE 2 (LOCATION: REAR FENDER) DECAL, PARKING BRAKE (LOCATION: PARKING BRAKE LEVER) LABEL- 2 (LOCATION: GRILLE SIDE PANEL) DECAL, TIRE SPECS (LOCATION: REAR MOTOR SHIELD) DECAL, CAUTION SHIFT 2 (LOCATION: TRANSAXLE SHIFT LEVER) DECAL, CAUTION TOW (LOCATION: STEERING COLUMN) DECAL, HANDS/BELT (LOCATION: FRONT GRILLE) DECAL, READ MANUAL (LOCATION: REAR MOTOR SHIELD) LABEL- HOOD, LH (LOCATION: LEFT SIDE OF HOOD) LABEL- HOOD, RH (LOCATION: RIGHT SIDE OF HOOD) DECAL, IGNITION (LOCATION: KEY SWITCH) DECAL, PTO CLUTCH (LOCATION: PTO LEVER) DECAL, TRANSAXLE 2-N- (LOCATION: FRONT TRANSAXLE SHIFT LEVER) DECAL, FLUID FILL (LOCATION: REAR OF FUEL TANK) DECAL, TRANSAXLE VENT (LOCATION: TRANSAXLE VENT VALVE) LABEL-EMBLEM, STEERING (LOCATION: CENTER OF STEERING WHEEL) DECAL, 2-N- VERTICAL (LOCATION: REAR TRANSAXLE SHIFT LEVER) LABEL-MADE IN USA (LOCATION: PTO CLUTCH LEVER) DECAL, CHOKE SYMBOL (LOCATION: CHOKE) DECAL, DIESEL FUEL (LOCATION: FUEL TANK FILLER DIESEL UNITS ONLY) DECAL, GASOLINE (LOCATION: FUEL TANK FILLER GASOLINE UNITS ONLY) 5

54 ROPS BAR WITH SEAT BELT (RB) FIGURE 25 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY ROLL BAR (NOT AVAILABLE AS A SERVICE PART) HEX, NUT / LOCKWASHR-HELICAL / WASHER-33/64x-/4x2GA WASHER-.56XX2GA BOLT-HEX /2-3X-/ NUT-HEX 7/ LOCKWSHR-HELICAL 7/ WSHR.443/.454XXGA B2 SPACER BOLT,7/6-4 X -/4 NC SEATBELT, 50"LONG 25-3 * LABEL-4 WHEEL DRIVE *4676 LABEL-MADE IN USA 25-5 * LABEL-ROLLBAR SPECS. *NOT ILLUSTRATED 52

55 REAR WEIGHT BAR (WB50) FIGURE 26 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY ROD-WEIGHT SECURITY WEIGHT, 50# PP0420 PRESTO PIN, /8 X 2-9/ DRAWBAR EXTENSION WEIGHT BAR BLT-HEX 5/8-X-/ LOCKWSHR-HELICAL 5/ NUT-HEX 5/ BOLT-HEX /2-3X-/ LOCKWSHR-HELICAL / HEX, NUT / BOLT-HEX 3/8-6X NUT-WLF 3/

56 PT HITCH REAR WEIGHT BAR (WB53) FIGURE 27 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY ROD, WEIGHT SECURITY WEIGHT, 50# PP0524 PRESTO PIN, 5/32x2-5/ FRAME, 3-PT WEIGHT BAR NUT-HEX 5/ LOCKWSHR-HELICAL 5/ LIFT PIN, CAT. O CLIP, CAT

57 FRONT WEIGHT BAR (WB40) FIGURE 28 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY ROD-WEIGHT SECURITY WEIGHT, 50# PP0524 PRESTO PIN, 5/32x2-5/ FRAME, FRONT WGHT BAR

58 PT HITCH HYDRAULICS (PT420) FIGURE 29 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY HANDLE-BENT VALVEBODY VALVE W/FLOAT & HNDLS T-6-6 FITTING, RUN TEE HOSE (/4 X 7) BRKT, COUPLER (ITEM 5 USED ON UNITS WITH KOHLER ENGINES ONLY) COUPLER, FEMALE NIPPLE FITTING 90 (ITEM 8 USED ON UNITS WITH KOHLER ENGINES ONLY) VALVE, SELECTOR 3 WAY FITTING STRAIGHT LOCKNUT-NYLON / LEVER, SELECTOR VALVE (ITEM 2 USED ON UNITS WITH KOHLER ENGINES ONLY) BOLT-HEX /4-20X HOSE, /4 X 65 00R # FITTING HOSE, /4 X 58 00R # CYLINDER PIN CYLINDER-LIFT BOLT-3/8-6X2-/4 HEX LOCKNUT-NYLON 3/ CP062 COTTER PIN, 3/6 X -/ MOUNT, 3-PT HITCH LEVER BOLT,/4-20 X -3/4 NC NUT-WLF / * DUST PLUG BRKT, COUPLER FITTING LEVER, SELECTOR VALVE (ITEMS USED ON UNITS WITH KUBOTA ENGINES ONLY) * NOT ILLUSTRATED 56

59 PT HITCH ATTACHMENT PARTS (PT420) FIGURE 30 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY LINK, TOP CAT ADJUSTER, LIFT (3-POINT) LINK, LIFT BOLT-3/8-6X2-/4 HEX ROCKSHAFT ASSEMBLY BLT-HEX 3/8-6X-/ NUT-3/8-6 HEX CLEVIS PIN, 3/8 X -/ CP0508 COTTER PIN, 5/32 X DRAFT LINK CHAIN, 3/6" 2 LINKS LOCKNUT-NYLON 3/ CLEVIS PIN, 5/8 X 2-/ PP038 PIN, 3/32 x 2-5/ E30 JAM NUT, 3/4-0 NC CLEVIS PIN, 5/8 X 2-3/ LOCKWASHER, 3/ WASHER.8X.406X6GA 4 57

60 DUAL WHEELS (DW00) FIGURE 3 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 3-99-F37 BOLT, /2-20x3 W/2-/4" TD HUB WHEEL ASSY W/2xx8 2 RAWHIDE TIRE, LEFT WHEEL ASSY W/2xx8 2 RAWHIDE TIRE, RIGHT 3-5 * WHEEL ASSY W/20x0x8 4 TURFMATE TIRE 3-6 * WHEEL ASSY W/22x2x8 4 FIELD TRAX TIRE (ITEMS 5 & 6 ARE THE OPTIONAL TIRE STYLES) DUAL, INNER SQ. DRIVE NUT,/2-20 NF DUAL, OUTER SQ. DRIVEN WHEEL NUT / DRAW NUT, HEX DUAL, HOOK BOLT * DECAL, DUAL TIRE INSTR * NOT ILLUSTRATED 58

61 OPTIONAL HYDRAULIC COOLER FIGURE 32 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY KIT-HYD OIL COOLER (INCLUDES ITEMS 2-2) HOSE, 3/8 X 56 00R # BLT-WLF /4-20X/ NUT-WLF / BRKT- L TYPE WEATHERSTRIP, 3/6X3/ BRKT- J TYPE COOLER-HYDRAULIC OIL NUT-HEX # LOCKWASHER WASHER-SQUARE SPEC SHROUD-OIL COOLER GROMMET, 3/8 ID X 7/8 OD STRAP-OIL COOLER MNT X/2 R MACH SCREW X2 R MACH SCREW BRKT-OIL COOLER, RIGHT BRKT-OIL COOLER, LEFT FAN-COOLING, 2V FITTING, SWITCH, PUSH-PULL 59

62 SUN SHADE CANOPY (SH) FIGURE 33 ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY CANOPY, 33-2 * CANOPY HEADLINER 33-3 * LABEL-STEINER DIECUT MOUNT, CANOPY RH 33-5 * MOUNT, CANOPY LH BOLT, 3/8-6X3 HEX WSHR.8X.406X6GA NUT, 5/ BOLT-5/6-8X3/4 WLF F303 NUT, FLANGED LOCK 4 * NOT ILLUSTRATED 60

63 Equipment from Jacobsen, a Textron company, is built to exacting standards ensured by ISO 900 and ISO 400 registration at all our manufacturing locations. A worldwide dealer network and factory-trained technicians backed by Textron Parts Xpress provide reliable, high-quality product support. BOB-CAT BROUWER BUNTON CUSHMAN RYAN STEINER