LIFTING DEVICE, duplex filter / in-line filter Series AHV
|
|
- Abner Waters
- 6 years ago
- Views:
Transcription
1 Series AHV Page 1/6 The lifting devices are intended for the maintenance of filters with blind fange filter lids. They are required, if on the site of the filter no other hoisting devices are available to lift of the filter s lid. When using the lifting device, it is highly recommended to follow the manual and maintenance instructions of the corresponding filter. This means especially, that prior to loosening the fixing screws of the filter s lid it is to be checked that there is no pressure on the filter and that pressure cannot build up. When checking the pressure relief, open the sealing screw on the lid prior to loosening and removing the fixing screws. After all safety measure are taken, this procedure is to be followed: - Removal of the fixing screws of the filter s lid (Connection of the lid and the housing flange) - Turning the toggle nut clockwise until the filter s lid is lifted at least 1.18 inch from the housing flange - Swaying the filter s lid around the axis of the lifting arm, until the lid is entirely removed from above the housing. - Maintenance of the filter according to the corresponding requirements - Swaying the filters lid around the axis of the lifting arm until the lid is placed in the center above the housing flange. - Turning the toggle nut counter clockwise until the filter s lid is lowered to the housing flange and until the disc between toggle nut and lifting arm is lifted at least.07 inch by the toggle nut. When lowering the filter s lid, it has to be ensured that the hole pattern of the flanges of lid and housing match. Also ensure the position of the breather bore hole. - Inserting and tightening the fixing screws according to the corresponding filter s manual and maintenance instructions All further procedures for maintaining filters are performed according to the corresponding filter s manual and maintenance instructions. Order identification The identification for ordering the device is effective without specific indications of angle positions in plain text, for example Lid lifting device. Ordering example: Filter DSF with lid lifting device The specific design corresponds to preferred angle position from the valid data sheet 1661, pages 1-6. In case other angle positions are requested, the order can be made according the the codes from data sheet 1661, pages 1-6. If that is the case, also the outside-pipe diameter, the pressure stage and the type of filter (In-Line filter/twin filter) have to be chosen. For example, a duplex filter with a pipe diameter of 20.00, pressure stage of 300 PSI (16 bars), material of c-steel (standard) filter 1 and 2, turning point of the lifting arm axis opposite to IN on the filters housing, meaning 180. Ordering example: AHV.FD
2 for pipe diameters of Page 2/6 AHV. FD pipe diameter:
3 for pipe diameters of Page 3/6 AHV. FD pipe diameter: AHV. FD pipe diameter: ,5 67, ,5 202, , ,5
4 for pipe diameters of Page 4/6 AHV. FD pipe diameter: ,5 112, , , ,5 292,5 315
5 for pipe diameters of Page 5/6 AHV. FD pressure stage 3 pipe diameter:
6 for pipe diameters of Page 6/6 AHV. FD pipe diameter :
INSTRUCTION MANUAL INSTALLING NEW GREASE IN UT SERIES PNEUMATIC ACTUATOR
INSTRUCTION MANUAL INSTALLING NEW GREASE IN UT SERIES PNEUMATIC ACTUATOR This instruction manual explains the steps required to degrease and install new grease into the Max-Air UT series pneumatic actuator.
More informationAxial Piston Fixed Motor A2FM
Axial Piston Fixed Motor A2FM RE 91001/06.2012 1/46 Replaces: 09.07 Data sheet Series 6 Size Nominal pressure/maximum pressure 5 315/350 bar 10 to 200 400/450 bar 250 to 1000 350/400 bar Open and closed
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationPipe Flaring Tool Kit (for on-car use)
4850 Pipe Flaring Tool Kit (for on-car use) www.lasertools.co.uk Introduction Flaring Tool Kit Components 4850 Brake Pipe Flaring Tool Kit (for on-car use) 1: De-burr tool 2: Hydraulic ram 7 2 5 Designed
More informationService and Maintenance. Repositioning of the Motor Conduit Box and Cable Entry Motor Frame Sizes
Service and Maintenance Repositioning of the Motor Conduit Box and Cable Entry Motor Frame Sizes 71-132 Overview 1 2 3 4 Safety Tooling Changing the Conduit Box Position Changing the Cable Entry Safety
More informationFlow Control. Before installation or maintenance, these instructions must be fully read and understood.
Before installation or maintenance, these instructions must be fully read and understood. Please read these instructions carefully. This symbol indicates important messages and safety instructions. Potentially
More informationGS-FLANGE SYSTEM. SAE psi
SAE 10000 psi Flange dimensions...160 Retain ring flanges...161 Grooving direct on to pipe...162 Flange for welding...163 Tee block, Elbow block...164 Blind flange...165 Seal carriers...166 Retain ring...167
More informationK, T, TK, TA and KC Series Operation and Maintenance Instructions
K, T, TK, TA and KC Series Operation and Maintenance Instructions Table of Contents Introduction... 1 General Description for K, T, TK & TA Series... 1 K Series Transmission........................................
More informationQuincy QR-25. Series Model 350. Quincy. Compressor. Parts Manual Record of Change 106
Quincy QR-5 Series Model 350 s Manual Record of Change 106 This manual contains important safety information and should be made available to all personnel who operate and/or maintain this product. Carefully
More informationFLOWSERVE CORPORATION NOBLE ALLOY VALVE PISTON CHECK VALVE REPAIR INSTRUCTIONS
FLOWSERVE CORPORATION NOBLE ALLOY VALVE PISTON CHECK VALVE REPAIR INSTRUCTIONS Cookeville Valve Operation 1978 Foreman Drive Cookeville, TN 38541 PH: 800-251-6761 931-432-4021 FAX: 931-432-5518 PISTON
More informationMaximum Motor Power 0.25 hp 0.19 kw Torque Range ft. lbs Nm. Torque Range ft. lbs Nm Non-Reversible
21MF-900/910 Series 21MR-910 Series 0.3 hp 0.22 kw 0.25 hp 0.19 kw 0.24 11.3 ft. lbs. 0.3 15.3 Nm 1.2 10.0 ft. lbs. 1.6 13.6 Nm Threaded or Keyed Spindle 21MF-900 21MR-911 Code 0, 1, 2 & 3 5.69 Code 4
More informationVexve Butterfly Valve User Manual p = PN 25 p = PN 20 (DN 1200)
30.03.2010 Vexve Butterfly Valve User Manual p = PN 25 p = PN 20 (DN 1200) Table of Contents 1. General 2. General Instructions and Cautions 3. Valve Markings 4. Valve Transportation and Storage 5. Installations
More informationThrottle check valve. RE 27518/10.07 Replaces: Type Z2FS
Throttle check valve RE 758/0.07 Replaces: 0.03 /8 Type ZFS Size 0 Component series 3X Maximum operating pressure 35 bar [4569 psi] Maximum flow 60 l/min [4.3 US gpm] H5556 Table of contents Content Page
More informationBray/ VAAS Slurry Series Knife Gate Valve 760/762/765/766/767/768 Series Operation and Maintenance Manual
Bray/ VAAS Knife Gate Valve 760/762/765/766/767/768 Series Table of Contents Definition of Terms 1 Safety Instructions 1 Introduction 2 Unpacking 2 Storage 2 Installation 3 Commissioning 3 Cylinder-Operated
More informationIOM Manual. IOM Manual. Series 76/77.
IOM Manual IOM Manual Series 76/77 www.flowlinevalves.com Flow Line Valve and Controls, L.L.C. 110 Main Project Road Schriever, LA 70395 P.O. Box 677 Schriever, LA 70395 Phone 985-414-6004 * Toll Free
More informationPROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
More informationKEYSTONE SERIES GRF RESILIENT SEATED BUTTERFLY VALVES INSTALLATION AND OPERATION MANUAL
Before installation these instructions must be fully read and understood Intended valve use The valve is intended to be used only in applications within the pressure/temperature limits indicated in the
More informationSTEAM ENGINE C&O No. 308
Deerfield and Roundabout Railway STEAM ENGINE C&O No. 308 Operational Information for Engineers September 2, 2018 4-6-4 Type Locomotive, for passenger & freight service. Patterned after Chesapeake & Ohio,
More informationSPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking
More informationINSTALLATION AND MAINTENANCE OF TOP LOADING ARM
INSTALLATION AND MAINTENANCE OF TOP LOADING ARM D TABLE OF CONTENTS 1. INTRODUCTION 04 2. SPECIFICATION OF THE REDLANDS LOADING ARM 04 3. INSTALLING THE LOADING ARM 3.1. Installation Procedures 05 4.
More informationSection X STEERING DATA AND SPECIFICATIONS. 21 degrees 45 minutes -f- or 1 degree (inner wheel when outer wheel is 20 degrees)
76 Section X DATA AND SPECIFICATIONS MODELS MC-1 MG-2 MC-3 MY-1 Steering Type Manual Power Worm and Three Tooth Roller None None None Rack and Gear Sector, Recirculating Ball Nut Ratio Manual 20.4... Power
More informationDescription of Bolt Torque Tables
Maximum (preferred) torque required per bolt (foot pounds) to arrive at the maximum available / recommended gasket stress shown in the previous column. (4) Maximum gasket stress recommended or available
More informationSub Section Title Page No.
Sub Section Title Page No. 1 Introduction 3 2 Routine Maintenance 3 3 Disassembly 4 3.1 Disassembly of Double Crank Design 4 3.2 Disassembly of Scotch Yoke Design 5 3.3 Disassembly of Actuator Cylinder
More informationSERVO SPIRAL BEVEL GEARBOX. Catalogue 05/11: The new servo-gearbox catalogue
Catalogue 05/11: The new servo-gearbox catalogue The family: Servo spiral bevel gearboxes. For toughest demands in dynamics Flexible Robust and durable For any installation position due to a flexible lubrication
More informationTBV OPERATION AND MAINTENANCE MANUAL SERIES 1800: FLANGED BALL VALVE. For technical questions, please contact the following:
TBV OPERATION AND MAINTENANCE MANUAL SERIES 1800: FLANGED BALL VALVE For technical questions, please contact the following: Engineering Department 1537 Grafton Road Millbury, MA 01527 Phone: (508) 887-9400
More informationAPP pump instruction APP and APP 16-22
MAKING MODERN LIVING POSSIBLE Instruction APP pump instruction APP 11-13 and APP 16-22 www.ro-solutions.com Table of Contents 1. Identification...2 2. System design...3 2.1 Open-ended systems with direct
More informationMMR20. Instruction Manual for Operation & Maintenance. IB International. Ph:
MMR20 Instruction Manual for Operation & Maintenance IB International www.ibinternational.com.au Ph: 07 3399 1288 Contents Introduction... 2 Identification Data... 2 Machine Controls & Components... 3
More informationAccumulator shut-off block. Type ABZSS. Contents. RE Edition: Replaces: 05.13
Accumulator shut-off block Type ABZSS RE 011 Edition: 2016-07 Replaces: 0.1 Nominal diameter DN08; DN10; DN20; DN0 Component series X Maximum operating pressure 0 bar [07 psi] HAD8066 Contents Features
More informationHIGH PRESSURE CONTROL VALVE PISTON BALANCED
PISTON BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be
More informationInstallation, Operation, and Maintenance Manual
Installation, Operation, and Maintenance Manual Welker Automatic Insertion Heated Regulator High Voltage Model IHRA-4SS-220/230 100 or more inch insertion length The information in this manual has been
More informationINSTALLATION, OPERATION, & MAINTENANCE MANUAL Models # MM-30, MM-30HT, MM-50, MM-50HT, & MM-50 EXL with Special HP Tool and Special HP EXL Tool
INSTALLATION, OPERATION, & MAINTENANCE MANUAL Models # MM-30, MM-30HT, MM-50, MM-50HT, & MM-50 EXL with Special HP Tool and Special HP EXL Tool INSTALLATION INSTRUCTIONS FOR THE MODEL MM-30 & MODEL MM-50
More informationPRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY
PRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been
More informationSPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
TEST AND ADJUSTMENT Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking (Minimum).......................... 28 kpa (4 psi) Oil Pressure.....................................
More informationAsepsis 21 Delivery Unit
INSTALLATION INSTRUCTIONS for the Console Mounted TM Asepsis 21 Delivery Unit SECTION I - REQUIREMENTS 1. PHYSICAL REQUIREMENTS... 1 2. ELECTRICAL REQUIREMENTS... 1 3. WATER SUPPLY REQUIREMENTS... 1 4.
More informationTechnical Data PR VALVE PRESSURE REGULATING VALVE
Technical Data PR VALVE PRESSURE REGULATING VALVE Applies to the following models only: - PR Please read carefully before commencing installation HYTEK (GB) LIMITED, Delta House, Green Street, Elsenham,
More informationDuplex Filter Pi Features. Nominal pressure 25/63 bar (360/900 psi), nominal size up to 450
Duplex Filter Pi Nominal pressure 25/63 bar (360/900 psi), nominal size up to 450 1. Features.High performance filters for modern hydraulic systems Modular system Compact design Minimal pressure drop through
More informationDRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I
DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION AXLE SHAFTS & BEARINGS Removal CAUTION: Failure to turn off air suspension power before raising vehicle may result in unexpected inflation or deflation of air springs. DO NOT reconnect
More informationPaint/Solvent/Dump Valve and Flow-Through Valve
Instruction Sheet P/N 08573D Paint/Solvent/Dump Valve and Flow-Through Valve. Description See Figure. The paint/solvent/dump valve is a normally-closed valve that opens to trigger and/or dump coating material.
More informationMounting and operating instructions EB 8220 EN. Pneumatic Butterfly Valve Type 3335/AT and Type 3335/3278. Fig. 2 Type 3335/AT
Pneumatic Butterfly Valve Type 3335/AT and Type 3335/3278 Fig. 2 Type 3335/AT Fig. 1 Type 3335/3278 with attached positioner Mounting and operating instructions EB 8220 EN Edition November 2000 Contents
More informationTHIS WARRANTY IS IN LIEU
Installation, Operation, Maintenance and Parts Manual for Backflow Prevention Assemblies Double Check Valve Assembly Series 2000DCA 4" 10" Double Check Detector Assembly Series 3000DCDC 4" 10" Reduced
More informationTS1251 PRESSURE DISPENSER USER'S MANUAL
TS1251 PRESSURE DISPENSER USER'S MANUAL TABLE OF CONTENTS SECTION DESCRIPTION PAGE NUMBER 1.0 CAUTIONS AND WARNINGS... 3 2.0 INTRODUCTION... 4 3.0 DESCRIPTION... 4 & 5 4.0 SET UP AND INSTALLATION... 6
More informationInstallation and Maintenance Instructions for Morin MRP Pneumatic Rack and Pinion Actuators
for Morin MRP Pneumatic Rack and Pinion Actuators Introduction The Morin MRP Pneumatic Actuator is a compact, rack & pinion design, conforming to Keystone standard or direct mount standards or EN ISO 5211
More information2200 North Main Street Washington, PA PH: FX:
2200 North Main Street 2200 North Main Street KVAB SERIES MEDICAL VALVES All valves MRI compatible - approved to 3 Tesla. Nominal stroke is 1.5 turns. Full flow at ⅓ turn. Strong, durable body is made
More informationSpecifications for: Hi-Way Model SA-6C 304 Stainless Steel Under Tailgate Spreader Comply to. Make and Model Bid: HOPPER AUGER MECHANISM
Hi-Way Model SA-6C 304 Stainless Steel Under Tailgate Spreader GENERAL 1. The under tailgate spreader required in these specifications shall be hydraulically operated and shall consist of a steel trough,
More informationLOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED
DIAPHRAGM BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to
More informationMGA Twin Cam Engine Assembly.
MGA Twin Cam Engine Assembly. The following article is a collection of notes of things to be observed in the assembling of MGA Twin Cam engines. To be read in conjunction with the Workshop Manual. It does
More informationKEYSTONE Figure 990/991 Butterfly valves Installation, operation and maintenance instructions
Before installation these instructions must be fully read and understood Potentially dangerous practices: disregarding instructions improper use of product use of insufficiently qualified personnel Application
More informationOPERATING AND MAINTENANCE MANUAL BATCH PRESSURE FILTER 3 GALLON CAPACITY
OPERATING AND MAINTENANCE MANUAL BATCH PRESSURE FILTER 3 GALLON CAPACITY SEPOR, INC 718 N FRIES AVE. WILMINGTON, CA 90744 310 830 6601 Fax: 310 830 9336 info@sepor.com Installation The 3 gallon batch pressure
More informationThrottle check valve. Type Z2FS. Features. Content. RE Edition: Replaces: 04.08
hrottle check valve ype Z2FS RE 27526 Edition: 205-0 Replaces: 04.08 Size 6 Component series 3X Maximum operating pressure 350 bar [5076 psi] Maximum flow 250 l/min [66 US gpm] tb022 Features Sandwich
More informationKLINGER Piston Valves KVN DN PN 16 I/III with valve ring KX-GT Modul
Page 1 Assembly Instructions and Handling Regulations for KLINGER Piston Valves KVN DN 65 150 PN 16 I/III with valve ring KX-GT Modul DN 125-150 1 Body 2 Bonnet 3 Hand wheel 4 Piston 5 Lantern bush 8 Threaded
More informationKEYSTONE OPTISEAL F14/16-15/17 AND BREWSEAL BUTTERFLY VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS
Before installation these instructions must be fully read and understood 4. Ozone: storage rooms should not contain any equipment generating ozone. E.g. lamps, electric motors. IMPORTANT Before valves
More informationBoston Gear ORC-F Series Trig-O-Matic Overload Release Clutches
Boston Gear ORC-F Series Trig-O-Matic Overload Release Clutches P-3002-BG Installation and Operation ORC-F Series a division of Altra Industrial Motion 2 Contents I. Introduction A. Operating Principle..............2
More informationINSTALLATION & MAINTENANCE MANUAL
INSTALLATION & MAINTENANCE MANUAL 3-WAY/4-WAY/5-WAY MULTI-PORT BALL VALVES T TEFLON PARTS - 1. Seat x 5 pcs. 2. Joint Gasket x 5 pcs. 3. Retainer Seal x 5 pcs. 4. Thrust Washer x 1 pc. 5. O-Ring x 1 pc
More informationFPC815 Pneumatic Rivet Tool
WARRANTY If you have any problems with this tool, please call FPC Corporation toll-free at 1-800-860-3838 before returning it to the place of purchase. FPC815 Pneumatic Rivet Tool FPC Corporation warrants
More informationFZ-A Lubricator. Electric, Oil & Grease. General. Application. Operation. Features. Adjustment of Discharge Rate R2 03/09
FZ- Lubricator Electric, Oil & Grease General The FZ- Lubricator is primarily designed for direct feed applications for servicing up to 12 lubrication points. The lubricators are supplied with pump bodies
More informationBSM ROTARY GEAR PUMPS
FT. MTD. PUMP BSM bronze pumps are ideal for use where corrosion resistant materials are required such as providing circulation on water-jacketed engines, pumping saline solutions as well as a variety
More informationFlow Meter Terminal Boxes
Shutter Flow Meter Terminal Boxes Shutter Flow meter Terminal boxes 02 07 11 1 Shutter Valve DAROC Description and general specifications Production range and operating conditions Operation Installation,
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0038 Fits: 2012-2015 F30 335i 2013-2015 F30 335i xdrive 2014-2015 F34 335i xdrive Gran Turismo 2014-2015 F32 435/435i xdrive 2014-2015 F33 435i Convertible/435i
More informationAxial Piston Fixed Pump A2FO
Electric Drives and Controls Hydraulics Linear Motion and Assembly Technologies Pneumatics ervice Axial Piston Fixed Pump A2FO RE 91401/03.08 1/24 Replaces: 09.07 Technical data sheet eries 6 izes Nominal
More information2005 Hyundai Tucson LX. On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
TIMING BELT NOTE: On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt. Removal 1. Remove the engine cover. See Fig. 1. 2. Remove right
More informationOPERATING, SERVICE AND MAINTENANCE MANUAL MODEL SCH 2900 MODEL SCH 3600 MODEL SCH 4900 PLANETARY WINCHES
OPERATING, SERVICE AND MAINTENANCE MANUAL MODEL SCH 2900 MODEL SCH 3600 MODEL SCH 4900 PLANETARY WINCHES CAUTION: READ AND UNDERSTAND THIS MANUAL BEFORE INSTALLATION AND OPERATION OF WINCH. SEE WARNINGS!
More informationBULLTIN B PISTON ACTUATOR. The Actuator that Delivers Maximum Torque for Minimum Air Consumption
BULLTIN B60 PISTON ACTUATOR The Actuator that Delivers Maximum Torque for Minimum Air Consumption TABLE OF CONTENTS: COMPACT DESIGN PRINCIPLE OF OPERATION PARTS LIST MAIN FEATURES TORQUEMETRIC TORQUEIMPERIAL
More informationBR 31a Rack-and-pinion Actuator,
Operating, assembly and maintenance instructions BR 31a Rack-and-pinion Actuator, SRP and DAP 1. General These instructions are intended to support the user in the assembly, maintenance, and repair of
More informationREAR SUSPENSION. Wheel Bearing and Wheel Hub. NOTE: All-Wheel Drive (AWD) shown, Front Wheel Drive (FWD) vehicles similar.
2009 Lincoln MKS AWD V6-3.7L Vehicle > Steering and Suspension > Wheels and Tires > Wheel Hub > Service and Repair > Removal and Replacement REAR SUSPENSION Wheel Bearing and Wheel Hub NOTE: All-Wheel
More information4. Remove the bed bolts A.) Using a 1/2 socket, remove the four inner bed bolts. B.) Using a T-25 Torx driver, remove the four outer bed bolts.
Installation Instructions Part Number 883-282 Intake kit with scoop 2008-14 Polaris Ranger RZR 800 Tools Required For Installation: 7/16 and 1/2 Wrenches. 10mm, 7/16, and 1/2 Sockets. T-25 Torx driver.
More informationOPERATION & MAINTENANCE INSTRUCTIONS MODEL: TC-300
1-800-223-4540 ** 602-437-5020 OPERATION & MAINTENANCE INSTRUCTIONS MODEL: TC-300 READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING MACHINE Contents Safety Instructions Pg 3 Operating Instructions Pg 4-5 (Light
More informationKeystone F89 pneumatic quarter-turn actuator General purpose / hazardous area
Compact, reliable and low operation costs for all types of quarter-turn valves are the keywords of the Keystone F89 range of pneumatic actuators Features Direct mounting to all Keystone butterfly valves
More informationKEYSTONE F89 pneumatic quarter-turn actuator GENERAL PURPOSE / HAZARDOUS AREA
compact, reliable and low operation costs for all types of quarter-turn valves are the keywords of the Keystone F89 range of pneumatic actuators FEATURES Direct mounting to all Keystone butterfly valves
More informationSeries 820 AWWA Butterfly Valves
Series 820 AWWA Butterfly Valves Installation, Operation and Maintenance September 2015 SP-820-IOM-0915A Series 820 AWWA Butterfly Valves Installation, Operation and Maintenance Contents General.....3
More informationInstallation, Operation and Maintenance Manual
Installation, Operation and Maintenance Manual for the MOGAS ISOLATOR 2.0 Floating Ball Valve 1, 1.5, 2, 3 and 4 inch PREPARE THE VALVE FOR INSTALLATION INSTALL THE VALVE PROPERLY MAINTAIN THE VALVE FOR
More informationREAD INSTRUCTIONS THOROUGHLY BEFORE OPERATING TC-6 TC-15 TC Fax
OPERATING MANUAL TC-6, TC-15A & TC16 FILTER CRUSHER TC-6 TC-15 TC-16 READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING Oct. 18, 2012 800.223.4540 3451 S. 40th Street Phoenix, AZ 85040 602.437.5020 www.tssissg.com
More informationTransmate. Installation & Operating Manual. Thank you for your purchase of the InsertaValve.
Installation & Operating Manual Thank you for your purchase of the InsertaValve. Please read and understand this operation manual. Our goal is to serve you, our customer. If you have any questions, complaints
More informationTransmission Overhaul Procedures-Bench Service
How to Assemble the Lower Reverse Idler Gear Assembly Special Instructions In 1996 Eaton changed the reverse idler system design. In the nut design, the reverse idler bearing was lubricated through a hole
More informationVariable Displacement Plug-In Motor A6VE
Electric Drives and Controls Hydraulics Linear Motion and Assembly echnologies Pneumatics Service Variable Displacement Plug-In Motor A6VE RE 91 606/06.05 1/16 Replaces: 05.99 echnical data sheet Series
More informationMogas MVP Installation, Operation And Maintenance Manual
Mogas MVP Installation, Operation And Maintenance Manual Congratulations on your purchase of a Mogas Valve For Power This pamphlet is intended to provide complete information on installation, operation,
More informationInstallation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited)
Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited) Installation Time: 6 Hours Tools Required: Floor Jack Jack Stands Ratchet Torque Wrench 15mm Socket 15mm
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS
TITAN pt. no.: 03 0000 0141 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS Extended Capacity Replacement
More informationINSTRUCTION INFORMATION FOR TYPE "DB" ELECTRIC DISC BRAKE (DB-0, DB-2, DB-4)
The Last Word in Cranes INSTRUCTION INFORMATION FOR TYPE "DB" ELECTRIC DISC BRAKE (DB-0, DB-2, DB-4) OPERATION Zenar's type "DB" brakes are classified as a holding or parking type electro-mechanical operated
More informationDescription of Bolt Torque Tables
Maximum (preferred) torque required per bolt (foot pounds) to arrive at the maximum available / recommended gasket stress shown in the previous column. (4) Maximum gasket stress recommended or available
More informationwww.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on
More informationFixed Displacement Motor AA2FM (A2FM)
Fixed Displacement Motor 2FM (2FM) Series 6, for Open and Closed Circuits xial Piston, ent xis Design 5800 psi 6500 psi rueninghaus Hydromatik Sizes 5 1000 Nominal Pressure up to Peak Pressure up to (400
More informationEXTRACTION CHECK VALVES TYPE C09.6
Application Extraction check valves are valves used to to prevent the back flow of the service fluid in extraction and bleed lines of steam turbines. Each extraction check valve is designed exactly for
More informationInstallation Instructions For Part Number: Scoop and Snorkel Kit
Installation Instructions For Part Number: 883-275 Scoop and Snorkel Kit 2008-14 Polaris Ranger RZR 800 800 E.F.I. Tools Required For Installation: 7/16 and 1/2 Wrenches. 10mm, 7/16, and 1/2 Sockets. T-25
More informationOperating Instructions & Parts Manual
Operating Instructions & Parts Manual Grainger Model No. 36NE14 Bucher Hydraulics Model No. M-4509-0217 Please read the instructions carefully and always operate this equipment in a safe manner. Unit Description:
More informationAPP S pumps APP S / APP S / APP S 21-38
MAKING MODERN LIVING POSSIBLE Instruction APP S 2.0-3.5 / APP S 5.1-9.0 / APP S 21-38 ro-solutions.com Instruction Table of Contents 1. Identification...2 2. System design...3 2.1 Open system design...3
More informationThrottle check valve. Type Z2FS. Size 16 Component series 3X Maximum operating pressure 350 bar [5076 psi] Maximum flow 250 l/min [66 US gpm]
hrottle check valve ype Z2FS Size 6 Component series 3X Maximum operating pressure 350 bar [5076 psi] Maximum flow 250 l/min [66 US gpm] tb022 able of contents Content Page Features Ordering code 2 Symbols
More informationEXHAUST SYSTEM GROUP 11 CONTENTS EXHAUST SYSTEM 11-1
EXHAUST SYSTEM 11-1 GROUP 11 EXHAUST SYSTEM CONTENTS Page Torque Reference 1 Intake Manifold.. 2 Exhaust Manifold 2 Manifold Meat Control Valve 5 P«pe Manifold Heat Control Valve Replacement. 6 Exhaust,
More informationBoston Gear ORC Series
Boston Gear ORC Series Trig-O-Matic Overload Release Clutches Installation and Maintenance Instructions Doc. No. ORC Series Model S www.bostongear.com ORC SERIES TRIG-O-MATIC OVERLOAD RELEASE CLUTCHES
More informationDP Series Diaphragm Valve Installation and Maintenance Instructions
DP Series Diaphragm Valve Installation and Maintenance Instructions Contents Installation Actuation Actuator Orientation Welding Testing Maintenance Kit Contents Tool Requirements Exploded View Replacing
More informationInstallation and Maintenance Instructions for Grinnell GRP Pneumatic Rack and Pinion Actuators
FLOW CONTROL for Introduction The Grinnell GRP Pneumatic Actuator is a compact, rack & pinion design, conforming to Grinnell standard or direct mount standards or EN ISO 5211 mounting configuration, depending
More informationOperating and Maintenance Instructions for: Figure 79 Pneumatic Actuators (U/E options)
for: Figure 79 Pneumatic Actuators (U/E options) Introduction The Keystone Figure 79 Pneumatic Actuator range is available in three mounting options, as follows:- 79U - Keystone Mounting Standard 79E -
More informationForce Flow 100. Owners Manual. Rev 8/03. PO Box 2626, W. Hardy Rd., Spring, Texas 77383, Order , Fax
Force Flow 100 Owners Manual Rev 8/03 Air Motor Air Motor On/Off Bucket Blow Off Valve Discharge Hose Coupler Air Motor Base Assy Lower Pump Assy Up / Down Toggle Switch Inline Needle Regulator Air Bleed
More informationExtended Capacity Replacement Tanks for RAM Cummins Diesel Trucks
TITAN pt. no.: 03 0000 0135 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
More informationINDICATES A POTENTIALLY HAZARDOUS SITUATION, WHICH IF NOT AVOIDED MAY RE- SULT IN MINOR OR MODERATE INJURY.
SB 158 Use this guide, PL814 (MIV-E), or PL815 (MIV-M) to replace a damaged disc or fix additional leaks in a Hale Manual (MIV-M) or Electric (MIV-E) Master Intake Valve (MIV) when the disc fails to shut
More informationBreathers. BF...3 & BF...4 Series INNOVATIVE FLUID POWER. ø D1 HEX. Specifications. Hydraulic Symbols. Model Code. Dimensions BF P 3 G 10 W 1.0 /.
BF...3 & BF...4 Series Maximum flow rate - 31 scfm / 230 gpm at 0.04 bar Epoxy coated steel cap Zinc-plated internals Threaded connection Pressurized breather with relief valve (optional - BF3 only) Phenolic
More informationMARATHON TELESCOPIC HOIST
Website: www.tbei.com E-mail: sales@tbei.com CRYSTEEL S MARATHON TELESCOPIC HOIST this manual must be included with the vehicle after completing the installation. Web Site E-Mail Phone (507) 726-2728 www.crysteel.com
More informationback to main page Type: Butterfly valves Instructions and Operation Manual Warning! Warning! Danger for life! 1. Intended use Danger for life!
Instructions and operation manual for butterfly valves This manual is intended to support the users of Herberholz butterfly valves type HRD/HRA, RD/RA, LDKE/LDKF for installation, operation and maintenance
More informationV&P SCIENTIFIC LEVITATION STIR BALL LOADER. VP 725C-96 Operating Instructions
V&P SCIENTIFIC LEVITATION STIR BALL LOADER VP 725C-96 Operating Instructions TECHNICAL NOTE 178 9823 Pacific Heights Boulevard, Suite T, San Diego, CA 92121 (858) 455-0643 Fax: (858) 455-0703 email: sales@vp-scientific.com
More information