TBV OPERATION AND MAINTENANCE MANUAL SERIES 1800: FLANGED BALL VALVE. For technical questions, please contact the following:

Size: px
Start display at page:

Download "TBV OPERATION AND MAINTENANCE MANUAL SERIES 1800: FLANGED BALL VALVE. For technical questions, please contact the following:"

Transcription

1 TBV OPERATION AND MAINTENANCE MANUAL SERIES 1800: FLANGED BALL VALVE For technical questions, please contact the following: Engineering Department 1537 Grafton Road Millbury, MA Phone: (508) Fax: (508) Page 1 of 5

2 TBV Inc. ball valves are designed and engineered to provide long lasting, trouble-free service when used in accordance with these instructions and specifications. All TBV Inc Series ball valves have been factory lubricated with Fluorolube lubricant for break-in purposes. This may be removed if desired. INSTALLATION 1. Unless otherwise specified (For example, services such as chlorine or hydrogen peroxide require cavity pressure relief), TBV Inc. valves are bi-directional and may be installed for flow in either direction, with no loss in performance. 2. During installation, it is recommended that the valve ball be left in the open position to prevent possible damage to the ball. In the closed position, the sealing surfaces of the ball are exposed to damage from pipe debris, tools, etc. Before operation, assure that the line and the valve has been flushed clean of all debris. 3. Flanged valves should be installed using flange gaskets appropriate for the intended service. Fire safe valves require high temperature gaskets. Tighten flange bolts evenly to torque values appropriate for the gasket and bolt materials. 4. After installation, cycle the valve several times to assure smooth operation. OPERATION 1. A quarter turn of the handle clockwise closes the valve and a quarter turn counterclockwise fully opens the valve. Visual indication of the ball position is determined by the handle or stem position: when the handle, or the stem flats, inline with the piping the valve is open; across the line, the valve is closed. 2. Leaving a soft-seated ball valve in a partially open position for an extended period of time may result in leakage due to seat deformation. Consult the factory for recommendations relative to modulating applications, and for valve purging procedures. 3. Any media that might solidify, crystallize or polymerize should not be allowed to stand in the ball valve cavities. In the event that this should happen, DO NOT force the valve in either direction; disassemble and clean before resuming service. 4. Break-away torque (i.e., force which must be exerted to start moving the valve ball) will vary depending on the media, pressure and length of time between cycles, as well as valve seat and packing materials. Consult the factory for specific values. MAINTENANCE A repair kit containing the appropriate number of components is available for rebuilding each size and configuration of valve. Be sure to specify the complete valve model number, and the TBV Inc. sales order number that is stamped on the valve body, when ordering. Additional components, such as balls, stems, etc. are also available for repair purposes. Refer to illustration for part identification. AT ALL STAGES OF THE FOLLOWING DIS-ASSEMBLY AND RE-ASSEMBLY PROCEDURES, CARE MUST BE TAKEN TO AVOID DAMAGE TO ALL SEALING SURFACES. Page 2 of 5

3 1. Before removing valve from line, make absolutely certain that line pressure is shut down, and that the line is vented, to remove all pressure from the valve. Operate the valve to assure that there is no pressure or media trapped within the valve body cavity. Flush the line as appropriate to remove harmful chemicals that may be present. 2. Remove the valve from the line. Be certain to fully decontaminate the valve, if it has been used in services that have any degree of toxicity. Wear protective gloves and clothing as appropriate to avoid contact with potentially harmful chemicals. 3. Remove the body bolts and/or nuts to allow disassembly of the end plate from the body. 4. Remove body seal from the end plate. 5. Rotate the ball so that it is free to slide out of the body. Remove the seats and ball. 6. If it is necessary to replace the stem packing, remove the handle nut, lock washer, handle, packing nut, stop plate, belleville washers, grounding spring, and follower, in order, as appropriate. Lower the stem through the body and remove from valve. Remove thrust bearing; it may be on the stem, or it may have remained in the body back counter bore. Remove the stem packing, taking extreme care so as not to damage the sealing surfaces in the packing bore of the body. 7. Clean and inspect all components, paying particular attention to areas that must maintain a seal: ball, seat pockets, finished stem diameters, stem bore, and body seal area. These areas must be free of scratches, pitting and other surface defects. 8. Lightly lubricate stem-packing components provided in repair kit with a lubricant that is compatible with the media. Loosely assemble stem packing by reversing the above disassembly procedure. 9. Lightly lubricate new seats. Insert seats into seat pockets, taking care that large radius of the seat is facing toward the ball. 10. Lightly lubricate ball. Rotate stem so that flats align with body bore. Insert ball, aligning stem slot with stem. Assemble into body cavity. 11. Place body seal in groove in end plate. Assemble to valve body-taking care to properly align seat and body seal. 12. Install body bolts (or studs) and nuts. Tighten evenly and gradually in a diagonal pattern until the end plate has metal-to-metal contact with the body. Tighten in accordance with good shop practice. General recommendations for torque values are as follows: BOLT SIZE TORQUE 1/4" foot-pounds 5/16" foot-pounds 3/8" foot-pounds 7/16" foot-pounds 1/2" foot-pounds 5/8" foot-pounds 3/4" foot-pounds 1" foot-pounds Page 3 of 5

4 13. Adjust stem packing as follows: a) Tighten packing nut firmly. The following approximate torque values are given as a guide. It is recommended that the packing be compressed, relaxed, and then re-compressed to these same values. This has been found to provide optimum life for the stem packing. NOTE: Periodic stem packing adjustment may be required depending on pressure and temperature and number of cycles. Refer to the recommended stem nut torque chart located below VALVE SIZE STEM NUT TORQUE 1/2" - 3/4" inch-pounds 1" inch-pounds 1 1/2" - 2" inch-pounds 3" - 4" foot-pounds 6" - 8" foot-pounds b) Cycle valve several times to assure smooth operation. c) It is recommended that the rebuilt valve be pressure tested prior to re-installation. Perform seat and shell tests using media compatible with the service, checking for any evidence of leakage. If necessary, adjust packing nut in 1/6-turn increments as necessary to stop leakage. Do not overtighten, as this will shorten the life of the packing. If there is leakage at the flange joint due to body seal leakage, verify proper and consistent body bolt torque. If leakage persists, check for proper installation of the body seals. d) Install valve in line following procedures described above. 14. Valve is now ready for service. Page 4 of 5

5 Exploded Views of 1800 Series ½ 2 Series 3 8 Series Page 5 of 5

INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS

INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS TC-3000T/B/S & TC-3000TC & TC-000 (FS)/00 (FS) THREE PIECE BALL VALVE, 000 WOG & 00/000 WOG TCI ball valves have been designed and engineered to provide you with long lasting trouble free service when

More information

INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS

INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS TC-0T/TC-0TM/TC-000/TC-0N/TC-0/TC-0M TWO PIECE BALL VALVE TCI ball valves have been designed and engineered to provide you with long lasting trouble free service when used in accordance with the instructions

More information

IOM-CleanFLOW TM. CleanFLOW Series Ball Valves. SV F Flow Controls I N C O R P O R A T E D

IOM-CleanFLOW TM. CleanFLOW Series Ball Valves. SV F Flow Controls I N C O R P O R A T E D !!!CAUTION! Safety Precautions!!! Before removing valve from pipeline NOTE that: Media flowing through a valve may be corrosive, toxic, flammable, a contaminant or harmful nature. Where there is evidence

More information

F8/FB8 Series Ball Valves IOM-F8/FB8

F8/FB8 Series Ball Valves IOM-F8/FB8 !!!CAUTION! Safety Precautions!!! Before removing valve from pipeline NOTE that: Media flowing through a valve may be corrosive, toxic, flammable, or a contaminant of harmful nature. Where there is evidence

More information

INSTALLATION & MAINTENANCE MANUAL

INSTALLATION & MAINTENANCE MANUAL INSTALLATION & MAINTENANCE MANUAL 3-WAY/4-WAY/5-WAY MULTI-PORT BALL VALVES T TEFLON PARTS - 1. Seat x 5 pcs. 2. Joint Gasket x 5 pcs. 3. Retainer Seal x 5 pcs. 4. Thrust Washer x 1 pc. 5. O-Ring x 1 pc

More information

E818/828 Series Fugitive Emissions 150# and 300# Flanged 2" - 8" Two-Piece Ball Valves Installation, Operation and Maintenance Instructions

E818/828 Series Fugitive Emissions 150# and 300# Flanged 2 - 8 Two-Piece Ball Valves Installation, Operation and Maintenance Instructions WCAIM2057 (Part 16774) E818/828 Series Fugitive Emissions 150# and 300# Flanged 2" - 8" Two-Piece Ball Valves Installation, Operation and Maintenance Instructions CAUTION: Flowserve recommends that all

More information

Metal Characterized-seated Control Valve 1. /4" 4" CPT 44 and 1 /2" 4" CPT 51/52 Installation, Operation and Maintenance Instructions

Metal Characterized-seated Control Valve 1. /4 4 CPT 44 and 1 /2 4 CPT 51/52 Installation, Operation and Maintenance Instructions 17812-N Metal Characterized-seated Control Valve 1 /4 4 CPT 44 and 1 /2 4 CPT 51/52 Installation, Operation and Maintenance Instructions CAUTION: Flowserve recommends that all products which must be stored

More information

Installation, Operation and Maintenance Instructions Series 608 Ball Valve

Installation, Operation and Maintenance Instructions Series 608 Ball Valve b. With valve open, remove three body bolts, loosen fourth and swing out body. Remove fourth bolt and spread pipe ends Close valve, remove ball, seats, body seals. Return body to its original position

More information

!!!CAUTION! Safety Precautions!!

!!!CAUTION! Safety Precautions!! !!!CAUTION! Safety Precautions!! Before beginning installation or maintenance be sure to read and understand this entire manual. Always use protective gear. MAINTENANCE GENERAL SVF CleanFLOW ball valves

More information

V-SEGMENT SERIES V-Port Segment Control Valves (VS/VV/VM) Installation & Maintenance Manual

V-SEGMENT SERIES V-Port Segment Control Valves (VS/VV/VM) Installation & Maintenance Manual CAUTION: 1. For your safety read this manual before installation or servicing. 2. Before installing or servicing, please ensure the line pressure has been relieved, and any hazardous fluids have been drained

More information

Power-Seal High Performance Butterfly Valve: Series P1 Installation & Maintenance Manual

Power-Seal High Performance Butterfly Valve: Series P1 Installation & Maintenance Manual CAUTION: 1. For your safety read this manual completely before installation or servicing. 2. Before installing or servicing, please ensure the line pressure has been relieved, and any hazardous fluids

More information

OPERATION AND MAINTENANCE INSTRUCTIONS

OPERATION AND MAINTENANCE INSTRUCTIONS OPERATION AND MAINTENANCE INSTRUCTIONS 334 SERIES THREE-PIECE BALL VALVES 1/4 to 2-1/2 Installation and Operation Always install your valve according to accepted industry standards and practices and operate

More information

When installing the screwed end, socket weld & flanged end valves the following respective procedures shall be followed for better performance.

When installing the screwed end, socket weld & flanged end valves the following respective procedures shall be followed for better performance. 1. Storage LARSEN & TOUBRO LIMITED Page 1 of 5 1.1. All valves are to be stored in fully open position, in order to protect the sphere surface and soft valve seats. 1.2. Before shipping, the inlet and

More information

IOM Manual. IOM Manual. Series 76/77.

IOM Manual. IOM Manual. Series 76/77. IOM Manual IOM Manual Series 76/77 www.flowlinevalves.com Flow Line Valve and Controls, L.L.C. 110 Main Project Road Schriever, LA 70395 P.O. Box 677 Schriever, LA 70395 Phone 985-414-6004 * Toll Free

More information

Installation, Operation and Maintenance Instructions

Installation, Operation and Maintenance Instructions Installation, Operation and Maintenance Instructions MODEL 5520 June 2002 1.0 GENERAL... 2 Model Number Information... 2 Features... 3 Specifications... 4 Table 1A. Flow Coefficients (C V ), Modified Percent

More information

MODEL 5540 CONTENTS. Installation, Operation and Maintenance Instructions 1.0 GENERAL

MODEL 5540 CONTENTS. Installation, Operation and Maintenance Instructions 1.0 GENERAL Installation, Operation and Maintenance Instructions MODEL 5540 Sep 20 CONTENTS.0 GENERAL. Model Number---------------------------------------------------------------------------------------------------------------

More information

HAYWARD FLOW CONTROL TBH SERIES TRUE UNION BALL VALVE INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

HAYWARD FLOW CONTROL TBH SERIES TRUE UNION BALL VALVE INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS HAYWARD FLOW CONTROL TBH SERIES TRUE UNION BALL VALVE INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS Pg. 1 of 10 PLEASE READ THE FOLLOWING INFORMATION PRIOR TO INSTALLING AND USING HAYWARD TBH SERIES

More information

PFA LINED BALL VALVES Installation, Operation and Maintenance Manual

PFA LINED BALL VALVES Installation, Operation and Maintenance Manual ACRIS PFA LINED BALL VALVES WWW.AMRESIST.COM Table of Contents Safety Instructions - Definition of Terms............................................2 Introduction..............................................................2

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

INSTALLATION, OPERATION AND MAINTENANCE MANUAL INSTALLATION, OPERATION AND MAINTENANCE MANUAL Full bore ball valve with flanged ends Ref. GENEBRE: 2526A 2528A 2529 1 Installation, operation and maintenance instructions 1. Products description... 3

More information

COMMERCIAL. BV & BVM Series Installation Instructions 06/29/15

COMMERCIAL. BV & BVM Series Installation Instructions 06/29/15 COMMERCIAL Bray Controls Commercial Division 13788 West Road, Suite 00A Houston, Texas 77041 BCDSales@Bray.com Phone: 1-888-41-79 Fax: 1-888-41-70 www.braycommercialdivision.com BV & BVM Series Installation

More information

Scope. Applicability. Caution. I & M CV3000 Series. Storage. Installation & Maintenance Instructions for Marwin CV3000 Series Three Piece Ball Valves

Scope. Applicability. Caution. I & M CV3000 Series. Storage. Installation & Maintenance Instructions for Marwin CV3000 Series Three Piece Ball Valves I & M CV3000 Series 3170 Wasson Road Cincinnati, OH 45209 USA Phone 513-533-5600 Fax 513-871-0105 marwin@richardsind.com www.marwinvalve.com Installation & Maintenance Instructions for Marwin CV3000 Series

More information

FLOWSERVE CORPORATION NOBLE ALLOY VALVE BALL VALVE REPAIR INSTRUCTION

FLOWSERVE CORPORATION NOBLE ALLOY VALVE BALL VALVE REPAIR INSTRUCTION FLOWSERVE CORPORATION NOBLE ALLOY VALVE BALL VALVE REPAIR INSTRUCTION Cookeville Valve Operation 1978 Foreman Drive Cookeville, TN 38541 PH: 800-251-6761 931-432-4021 FAX: 931-432-5518 CONTENTS FLOWSERVE/NOBLE

More information

DOUBLE OFFSET BUTTERFLY VALVE

DOUBLE OFFSET BUTTERFLY VALVE Flange STD: ASME CLASS 150 LB ASME CLASS 300 LB Temp :210 ~29 Work pressure: VF-91_/92_/93_ 2 ~48 150LB VF-94_/95_/96_ 2 ~24 300LB Pd. date 2011.5 Please read all of these instructions before installing

More information

Mogas MVP Installation, Operation And Maintenance Manual

Mogas MVP Installation, Operation And Maintenance Manual Mogas MVP Installation, Operation And Maintenance Manual Congratulations on your purchase of a Mogas Valve For Power This pamphlet is intended to provide complete information on installation, operation,

More information

THD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS

THD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS THD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS INTRODUCTION A-T Controls THD scotch yoke actuators have been designed and engineered to

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM)

INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM) INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM) IOM-1088 03-16 Model 1088 Vacu-Gard Blanketing Valve ISO Registered Company SECTION I I. DESCRIPTION AND SCOPE The Model 1088 Vacu-Gard is a tank blanketing

More information

KTM Hindle Series 300 Ultra-Seal two piece metal seated ball valves Installation and Maintenance Instructions

KTM Hindle Series 300 Ultra-Seal two piece metal seated ball valves Installation and Maintenance Instructions Before installation these instructions must be fully read and understood Warning For safety reasons, it is important to take the following precautions before you start work on the valve: 1. Personnel making

More information

Apollo Standard Port, Full Port & One Piece Flanged Ball Valves Installation, Operation, & Maintenance Guide

Apollo Standard Port, Full Port & One Piece Flanged Ball Valves Installation, Operation, & Maintenance Guide I854000.F M16005 Apollo Standard Port, Full Port & One Piece Flanged Ball Valves Introduction This manual presents guidelines for the Installation, Operation and Maintenance of manual and automated Apollo

More information

PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance

PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance ACECO Valve P.O. Box 9 Mounds, Oklahoma 74047 PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance Doc. No.: IOM-PV4-.0 Date: 6/0-00 Revision: A Contents: Installation Operation

More information

MERIDIAN, 2 or 3 PIECE, TRUNNION MOUNTED BALL VALVES

MERIDIAN, 2 or 3 PIECE, TRUNNION MOUNTED BALL VALVES INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS MERIDIAN, 2 or 3 PIECE, TRUNNION MOUNTED BALL VALVES Size Range 2 48 ASME Classes 150-2500 *It is recommended that the valve installer is familiar with

More information

IOM Manual. IOM Manual. Series 20/21.

IOM Manual. IOM Manual. Series 20/21. IOM Manual IOM Manual Series 20/21 www.flowlinevalves.com Flow Line Valve and Controls, L.L.C. 110 Main Project Road Schriever, LA 70395 P.O. Box 677 Schriever, LA 70395 Phone 985-414-6004 * Toll Free

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL FOR INSTRUMENT ISOLATION VALVE

INSTALLATION, OPERATION AND MAINTENANCE MANUAL FOR INSTRUMENT ISOLATION VALVE PAGE : 01 OF 07 INSTALLATION, OPERATION AND MAINTENANCE MANUAL FOR INSTRUMENT ISOLATION VALVE PREPARED BY CHECKED BY APPROVED BY NAME M.Bhuvaneswari Y.Nesabalan M.Selvam DATE 22-Mar-201 19-Nov-2013 22-Nov-2013

More information

GT-200 GATE VALVES PN16, Screwed end

GT-200 GATE VALVES PN16, Screwed end Document No. : MD-QO-04-281 Date : 2009/07 /17 Version : 1.0 GT-200 GATE VALVES PN16, Screwed end USER MANUAL Modentic Industrial Corporation 14F-1,No.57Taya Rd.,Taichung,Taiwan,R.O.C. Email:modentic@ms9.hinet.net

More information

5000/6000 SERIES BALL VALVES INSTALLATION - MAINTENANCE MANUAL

5000/6000 SERIES BALL VALVES INSTALLATION - MAINTENANCE MANUAL Date: August 2011 / Page 1 of 6 5000/6000 SERIES BALL VALVES INSTALLATION - MAINTENANCE MANUAL DESIGN The design features three piece construction and a free floating ball allowing ease of maintenance

More information

/2" 2" Series 94 and FZ94 Three-Piece Ball Valves, 1

/2 2 Series 94 and FZ94 Three-Piece Ball Valves, 1 06957-L 1 /2" 2" Series 94 and FZ94 Three-Piece Ball Valves, 1 /2" 6" Series 94 and FZ94 150/300, 1" 2" Series 94 600, and 4" 6" Series AF94 150/300 Flanged One-Piece Ball Valves Installation, Operation

More information

Fisher V270 Full-Bore Ball Control Valve

Fisher V270 Full-Bore Ball Control Valve Instruction Manual V270 Valve Fisher V270 Full-Bore Ball Control Valve Contents Introduction... 1 Scope of Manual... 1 Description... 1 Specifications... 2 Educational Services... 3 Installation... 3 Maintenance...

More information

Ver Trunnion Ball Valve INSTALLATION, OPERATION AND MAINTENANCE MANUAL FBV/IOM/BA02

Ver Trunnion Ball Valve INSTALLATION, OPERATION AND MAINTENANCE MANUAL FBV/IOM/BA02 Ver. 2008 Trunnion Ball Valve INSTALLATION, OPERATION AND MAINTENANCE MANUAL FBV/IOM/BA02 TABLE OF CONTENTS 1 APPLICATIONS...2 1.1 Applications...2 1.2 Performance Specifications...2 2 APPLICABLE STANDARDS...2

More information

McCannalok HIGH PERFORMANCE BUTTERFLY VALVE OPERATION AND MAINTENANCE MANUAL. The High Performance Company

McCannalok HIGH PERFORMANCE BUTTERFLY VALVE OPERATION AND MAINTENANCE MANUAL. The High Performance Company McCannalok HIGH PERFORMANCE BUTTERFLY VALVE OPERATION AND MAINTENANCE MANUAL The High Performance Company Table of Contents Safety Information - Definition of Terms... 1 Introduction... 1 Installation...

More information

Diaphragm Valves Type 15

Diaphragm Valves Type 15 Serial No. H-V031-E-8 Diaphragm Valves Type 15 User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instructions for

More information

FIGURE 310AM, 310AMSW & 311AM 3-PIECE BALL VALVE

FIGURE 310AM, 310AMSW & 311AM 3-PIECE BALL VALVE INTRODUCTION This instruction manual includes installation, operation and maintenance information for the figure 310AM, 310AMSW, and 311AM 3-piece 1000CWP, threaded end (NPT) or socket weld end (SW) ball

More information

Butterfly valves Figure 56 Installation & Maintenance Instructions

Butterfly valves Figure 56 Installation & Maintenance Instructions KEYSTONE Please read these instructions carefully This symbol indicates important messages and safety instructions. Hazard potentials: disregarding of instructions improper use of product insufficiently

More information

Series A Floating Ball Valve Installation, Operation & Maintenance XXXX - X X X X X X X. Base Part Numbers. Trim Option Suffix Code

Series A Floating Ball Valve Installation, Operation & Maintenance XXXX - X X X X X X X. Base Part Numbers. Trim Option Suffix Code Series A Floating Ball Valve Installation, Operation & Maintenance Base Part Numbers RATING 1 FP 2 RP 2 FP 3 RP 3 FP 4 RP 4 FP 1000 1102 1103 1104 1106 1105 1107 1500 1151 1152 1153 1154 1156 1155 1157

More information

Operation & Maintenance Manual 4900 Series Pipeline Injection Pumps Bulletin 150

Operation & Maintenance Manual 4900 Series Pipeline Injection Pumps Bulletin 150 340 West Benson Avenue Grantsburg, WI 54840 1-800-366-1410 715-463-5177 www.northern-pump.com Table of Contents Introduction... 3 Rotation... 4 Hydraulic Balance... 5 Cautionary Statements... 6 Pump Installation...

More information

CompoSeal butterfly valves, wafer style Installation & Maintenance Instructions

CompoSeal butterfly valves, wafer style Installation & Maintenance Instructions Please read these instructions carefully This symbol indicates important messages and safety instructions. Intended valve use The valve is intended to be used only in applications within the pressure/temperature

More information

Northern Pump A Division of McNally Industries, LLC

Northern Pump A Division of McNally Industries, LLC Operation & Maintenance Manual for Northern 4900 Injection Operation & Maintenance Manual For Northern 4900 Injection Northern Pump A Division of McNally Industries, LLC 340 West Benson Avenue Grantsburg,

More information

Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual Industrial Process Installation, Operation, and Maintenance Manual Cam-Tite Ball Valve Table of Contents Table of Contents Introduction and Safety...2 Safety message levels...2 User health and safety...2

More information

DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION:

DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION: DELTA O-RING CARTRIDGE SEAL ASSEMBLY AND INSTALLATION INSTRUCTIONS INTRODUCTION: These instructions are provided to familiarize the user with the seal and its use. The instructions must be read carefully

More information

Flow Line Controls. Installation & Operations Manual SERIES 20/21 Pneumatic Actuators

Flow Line Controls. Installation & Operations Manual SERIES 20/21 Pneumatic Actuators Flow Line Controls Installation & Operations Manual SERIES 20/21 Pneumatic Actuators Flow Line Controls, Inc. P.O. Box 677 Schriever, LA 70395 Phone: 985-414-6003 Toll Free 1-800-815-9226 Fax 985-414-6072

More information

DEMCO Model DM Gate Valves

DEMCO Model DM Gate Valves Page of 24 Installation, Operation, Maintenance and Repair Manual DEMCO Model DM Gate Valves Classes : 400 000 600 2000 900 3000 500 5000 Page 2 of 24 Published May 2002 Cooper Cameron Corporation, Cooper

More information

FIGURE 310A & 311A 3-PIECE BALL VALVE

FIGURE 310A & 311A 3-PIECE BALL VALVE INTRODUCTION This instruction manual includes installation, operation and maintenance information for the figure 310A, 310ASW, 311A, and 311ASW 3-piece 1000CWP, threaded end (NPT) or socket weld end (SW)

More information

Amerigear SF Spindle

Amerigear SF Spindle Amerigear SF Spindle Installation and Maintenance Manual Form No. 381-SH, 4/01 Spindle Installation and Maintenance Manual TABLE OF CONTENTS SECTION TITLE PAGE 1 Introduction...: 3 2 General Information...:

More information

Installation, Operation, and Maintenance Manual Full Port Y-Pattern, Bolted Bonnet, Globe and Check Valves

Installation, Operation, and Maintenance Manual Full Port Y-Pattern, Bolted Bonnet, Globe and Check Valves SMITH VALVES Installation, Operation, and Maintenance Manual Full Port Y-Pattern, Bolted Bonnet, Globe and Check Valves Globe Valve Series: YG80/YG15 Welded Bonnet Globe Valve Series: YG87/YG17 Piston

More information

GATE VALVES. Type P (Standard: Plug) Type S (Soft Seal) Contents. (1) Be sure to read the following warranty clauses of our product 1

GATE VALVES. Type P (Standard: Plug) Type S (Soft Seal) Contents. (1) Be sure to read the following warranty clauses of our product 1 Serial No. H-V011-E-12 GATE VALVES Type P (Standard: Plug) Type S (Soft Seal) Contents (1) Be sure to read the following warranty clauses of our product 1 User s Manual (2) General operating instructions

More information

Spring Brake Application

Spring Brake Application Technical Tip Maxibrake I Series Spring Brakes Disassembly, Inspections and Reconditioning Instructions Maxibrake I Series spring brake products are mechanical devices and are subject to wear after extended

More information

Operation & Maintenance Manual For 4900 Series Pumps Bulletin 134

Operation & Maintenance Manual For 4900 Series Pumps Bulletin 134 For 340 West Benson Avenue Grantsburg, WI 54840 1-800-366-1410 715-463-5177 www.northern-pump.com Table of Contents Introduction... 3 Cautionary Statements... 5 Pump Installation... 6 Removal from Installation...

More information

26 Series Stainless Steel 2-way Ball Valves

26 Series Stainless Steel 2-way Ball Valves 1-800-899-0553 26 Series Stainless Steel 2-way Ball Valves Users Manual Installation, Operation, & Maintenance 1. General Precaution 1.1. Material Section Material deterioration is determined by the contained

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual brands you trust. Installation, Operation and Maintenance Manual Trunnion Ball Design 1. Maintenance Page 3 2. Exploded view Page 4 3. Dissassembly, Inspection Page 5 4. Reassembly Page 5-8 CAUTION READ

More information

Fisher RSS Lined Globe Valve

Fisher RSS Lined Globe Valve Instruction Manual D0990 November 009 RSS Valve Fisher RSS Lined Globe Valve Contents Introduction............................... Scope of Manual.......................... Description...............................

More information

Fisher RSS Lined Globe Valve

Fisher RSS Lined Globe Valve Instruction Manual D0990 RSS Valve July 07 Fisher RSS Lined Globe Valve Contents Introduction... Scope of Manual... Description... Educational Services... Specifications... Installation... Maintenance...

More information

BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS

BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS PART NUMBER: 102264 REVISION: "C" DATE: November 2000 Page 1 of 11 1.0 INTRODUCTION 1.1

More information

2.- HANDLING OF VALVES BEFORE ASSEMBLY 3.- FITTING THE VALVE TO THE REST OF THE ASSEMBLY 5.- PERIODICAL INSPECTION OF THE VALVE AND MAINTENANCE

2.- HANDLING OF VALVES BEFORE ASSEMBLY 3.- FITTING THE VALVE TO THE REST OF THE ASSEMBLY 5.- PERIODICAL INSPECTION OF THE VALVE AND MAINTENANCE Page 1 of 16 CONTENTS 1.- INTRODUCTION 2.- HANDLING OF VALVES BEFORE ASSEMBLY 3.- FITTING THE VALVE TO THE REST OF THE ASSEMBLY 4.- OPERATION OF A BALL VALVE 5.- PERIODICAL INSPECTION OF THE VALVE AND

More information

MEMORY SEAL BALL VALVES MAINTENANCE MANUAL 2 12, Class 150 & 300, Regular Port, Flanged Unibody

MEMORY SEAL BALL VALVES MAINTENANCE MANUAL 2 12, Class 150 & 300, Regular Port, Flanged Unibody MEMORY SEAL BALL VALVES MAINTENANCE MANUAL 2 12, Class 150 & 300, Regular Port, Flanged Unibody I INTRODUCTION These rugged, versatile, high performance, regular port, ball valves meet all requirements

More information

Val-Matic QuadroSphere Trunnion Mounted Ball Valve

Val-Matic QuadroSphere Trunnion Mounted Ball Valve Manual No. QS-OM1-1 Val-Matic QuadroSphere Trunnion Mounted Ball Valve Operation, Maintenance and Installation Manual INTRODUCTION... 2 RECEIVING AND STORAGE... 2 INSTALLATION... 2 DESCRIPTION OF OPERATION...

More information

Keystone Series GR resilient seated butterfly valves GRW/GRL Installation and operation manual

Keystone Series GR resilient seated butterfly valves GRW/GRL Installation and operation manual Before installation these instructions must be fully read and understood Important Before valves are installed or used the following actions are recommended. 1. Valves/parts have to be inspected and thoroughly

More information

JT SERIES ANGLE STEM TANK BOTTOM BALL VALVE DN25 DN150. Installation, Maintenance and Operating Instructions

JT SERIES ANGLE STEM TANK BOTTOM BALL VALVE DN25 DN150. Installation, Maintenance and Operating Instructions JT SERIES ANGLE STEM TANK BOTTOM BALL VALVE DN25 DN150 Installation, Maintenance and Operating Instructions IMO-235 EN 3/2019 2 IMO-235 EN TABLE OF CONTENTS 1. GENERAL... 3 1.1 Scope of the Manual... 3

More information

Butterfly Valve Type 58 (PDCPD)

Butterfly Valve Type 58 (PDCPD) Serial No. H-V074-E Butterfly Valve Type 58 (PDCPD) 700mm (28 ) User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General

More information

KEYSTONE OPTISEAL F14/16-15/17 AND BREWSEAL BUTTERFLY VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS

KEYSTONE OPTISEAL F14/16-15/17 AND BREWSEAL BUTTERFLY VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS Before installation these instructions must be fully read and understood 4. Ozone: storage rooms should not contain any equipment generating ozone. E.g. lamps, electric motors. IMPORTANT Before valves

More information

Railroad Ball Valves Series 5REB3

Railroad Ball Valves Series 5REB3 Railroad Ball Valves Series 5REB3 4" (DN 00) Installation, Maintenance and Operating Instructions IMO-R4 /05 IMO-R4 Table of Contents GENERAL.................................... 3. Scope of the Manual........................

More information

Operating & Maintenance Manual For Steam Conditioning Valve

Operating & Maintenance Manual For Steam Conditioning Valve For Steam Conditioning Valve 1 Table of Contents 1.0 Introduction 3 2.0 Product description 3 3.0 Safety Instruction 4 4.0 Installation and Commissioning 5 5.0 Valve Disassembly 6 6.0 Maintenance 6 7.0

More information

THREE PIECE TRUNNION MOUNTED BALL VALVE

THREE PIECE TRUNNION MOUNTED BALL VALVE Page: 1 of 13 INSTALLATION, OPERATION & MAINTENANCE MANUAL KF SERIES P3/M3 THREE PIECE TRUNNION Page: 2 of 13 CONTENTS BILL OF MATERIALS --------------------------------------------------------------------------------------------------------------------------------------------------

More information

KEYSTONE. Butterfly valves Figure 9 Installation & Maintenance Instructions. Please read these instructions carefully

KEYSTONE. Butterfly valves Figure 9 Installation & Maintenance Instructions.  Please read these instructions carefully KEYSTONE Please read these instructions carefully This symbol indicates important messages and safety instructions. Hazard potentials: disregarding of instructions improper use of product insufficiently

More information

Parts List Single Reduction Models, Cast Iron Units

Parts List Single Reduction Models, Cast Iron Units Parts List Single Reduction Models, Cast Iron Units 60 51 51 10 24 11 11 9 24 12 19 17 27 31 8 23 7 14 20 28 26 5 1 2 6 44 60 50 23 7 6 30 27 30 4 3 30 13 29 14 22 18 27 43 48 50 8 15 16 12 25 9 51 51

More information

HYDRAULIC PUMP. INSTALLATION, OPERATION, & MAINTENANCE MANUAL MAINTENANCE MANUAL #: MM-HP Rev. A Page 1 of 12

HYDRAULIC PUMP. INSTALLATION, OPERATION, & MAINTENANCE MANUAL MAINTENANCE MANUAL #: MM-HP Rev. A Page 1 of 12 INSTALLATION, OPERATION, & #: MM-HP001 4-20-09 Rev. A Page 1 of 12 HYDRAULIC PUMP PART NUMBER HP46982ALSL & HP46982SL HYDRAULIC PUMP MM-HP001 Rev. A Page 2 of 12 Table of Contents 1.0 General Page 3 2.0

More information

Installation Operation Maintenance

Installation Operation Maintenance Worcester 459 / 599 Series Large three-piece reduced / full bore ball valves Installation Operation Maintenance WCENIM0019-02 Original Instructions Copyright All rights reserved. No part of these instructions

More information

KHR Series Regulators

KHR Series Regulators KHR Series Regulators Maintenance Instructions Kit Contents retainer Poppet Poppet spring Poppet damper Outer body seal Inner body seal Upper piston seal seal backup ring Main piston seal vent seal Self-vent

More information

Diaphragm Valve Type 72

Diaphragm Valve Type 72 Serial No. H-V001-E-8 Diaphragm Valve Type 72 User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instructions for

More information

Series VF Floating Ball Valve Installation, Operation & Maintenance XXXX - X X X X X X XX XX. Base Part Numbers CONTENTS. Trim Option Suffix Code

Series VF Floating Ball Valve Installation, Operation & Maintenance XXXX - X X X X X X XX XX. Base Part Numbers CONTENTS. Trim Option Suffix Code Series VF Floating Ball Valve Installation, Operation & Maintenance CONTENTS I. Introduction Page 1 Base Part Numbers & Suffix Code Page 1 II. Transportation & Storage Page 1 III. Installation Page 1 IV.

More information

SM64052 Maintenance & Repair Manual Commercial 2" Unisex Coupling - Valved Model 64052

SM64052 Maintenance & Repair Manual Commercial 2 Unisex Coupling - Valved Model 64052 Aerospace Group Conveyance Systems Division Carter Brand Ground Fueling Equipment SM64052 July 2004 Applicable additional manuals: SM64051 Commercial 2" Unisex Coupling, Non-Valved Maintenance & Repair

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL

INSTALLATION, OPERATION AND MAINTENANCE MANUAL INSTALLATION, OPERATION AND MAINTENANCE MANUAL LUDLOW SERIES FIGURE 340-S 3 to 14 Lever & Spring Swing Check Valves TABLE OF CONTENTS Introduction. 1 Description of Operation... 1 Receiving & Storage...

More information

STAINLESS STEEL SERIES LSSW HIGH PRESSURE HYDRAULIC CYLINDERS INSTALLATION & OPERATING INSTRUCTIONS

STAINLESS STEEL SERIES LSSW HIGH PRESSURE HYDRAULIC CYLINDERS INSTALLATION & OPERATING INSTRUCTIONS CATALOG: LSSW-00 STAINLESS STEEL SERIES LSSW HIGH PRESSURE HYDRAULIC CYLINDERS INSTALLATION & OPERATING INSTRUCTIONS REMEMBER.... WHEN PERFORMANCE COUNTS SPECIFY LEHIGH LEHIGH FLUID POWER, INC. 1413 ROUTE

More information

Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822

Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822 Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822 Statements: NIBCO High Performance Butterfly Valves, Series 6822 and 7822, have been designed

More information

McCannaseal Ball Valves Installation, Operation and Maintenance Instructions

McCannaseal Ball Valves Installation, Operation and Maintenance Instructions MMAIM2007 Part MV 570 McCannaseal Ball Valves Installation, Operation and Maintenance Instructions STEM HANDLE RETAINER NUT STEM NUT BONNET TRAVEL STOP GLAND RING BONNET FASTENERS GROUNDING WASHER BODY

More information

Newco / OIC / Cooper Forged Valves. Operation & Maintenance. Manual

Newco / OIC / Cooper Forged Valves. Operation & Maintenance. Manual NEWCO / OIC / COOPER VALVES Newmans Inc., Newmans Valve Ltd. Operation & Maintenance Manual Revision 2, 9 May 2007 1. Introduction and Safety Information... 1 1.1. Introduction... 1 1.2. Safety Information...

More information

Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual Industrial Process Installation, Operation, and Maintenance Manual Series PBV Plastic Lined Ball Valve Table of Contents Table of Contents Introduction and Safety...2 Safety message levels...2 User health

More information

INSTALLATION & MAINTENANCE MODEL mm

INSTALLATION & MAINTENANCE MODEL mm MODEL 65-25mm INSTALLATION INSTRUCTIONS CAUTION: Installation of Backflow Preventers must be performed by qualified, licensed personnel. The installer should be sure the proper device has been selected

More information

Bray/McCannalok High Performance Butterfly Valve Operation and Maintenance Manual

Bray/McCannalok High Performance Butterfly Valve Operation and Maintenance Manual Bray/McCannalok High Performance Butterfly Valve Operation and Maintenance Manual Table of Contents Definition of Terms 1 Introduction 1 Installation 1 Maintenance 2 Stem Seal Replacement 4 Seat Replacement

More information

3, 4 & 6 (DN 80, 100 & 150) CLASS 150 & 300 STANDARD BORE SERIES 7150, 730S & 7300 FLANGED BALL VALVES EQUIPPED WITH KEROTEST HANDLE ASSEMBLIES

3, 4 & 6 (DN 80, 100 & 150) CLASS 150 & 300 STANDARD BORE SERIES 7150, 730S & 7300 FLANGED BALL VALVES EQUIPPED WITH KEROTEST HANDLE ASSEMBLIES 3, 4 & 6 (DN 80, 100 & 150) CLASS 150 & 300 STANDARD BORE SERIES 7150, 730S & 7300 FLANGED BALL VALVES EQUIPPED WITH KEROTEST HANDLE ASSEMBLIES Installation, Maintenance and Operating Instructions IMO-261

More information

KENNEDY VALVE Plant and Industrial Group 1021 East Water Street Elmira, New York Telephone (607) Fax (607)

KENNEDY VALVE Plant and Industrial Group 1021 East Water Street Elmira, New York Telephone (607) Fax (607) KENNEDY VALVE Plant and Industrial Group 1021 East Water Street Elmira, New York 14901 Telephone (607) 734-2211 Fax (607) 734-3288 INSTALLATION, OPERATION, AND MAINTENANCE MANUAL General ECCENTRIC PLUG

More information

Table of Contents Visual Inspection and Neutralizing... 3 Disassembly

Table of Contents Visual Inspection and Neutralizing... 3 Disassembly 1 Table of Contents Visual Inspection and Neutralizing... 3 Disassembly... 3... 4... 4 Cleaning... 4 Inspection... 4 Reconditioning of Valve Seats... 5 Lapping Procedures... 5 Lapping Blocks... 5 Lapping

More information

Full View Flow Indicator

Full View Flow Indicator Full View Flow Indicator Threaded and Flanged Process Connection Installation / Operation / Maintenance Manual P.O. Box 1116 Twinsburg, OH 44087 Phone: 330/405-3040 Fax: 330/405-3070 E-mail: view@ljstar.com

More information

WARNING Carefully Read These Instructions Before Use

WARNING Carefully Read These Instructions Before Use DO NOT RETURN THIS SPRAYER TO STORE Call: 1-800-950-4458 Backpack Sprayer Use and Care Manual Manufactured for Northern Tool + Equipment Co., Inc. WARNING Carefully Read These Instructions Before Use Model

More information

LOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED

LOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED DIAPHRAGM BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to

More information

DEMCO DEMCO RESILIENT SEATED BUTTERFLY VALVE. Installation, Operation and Maintenance Manual D I S T R I B U T E D V A L V E S DEM-RSBV-IOM

DEMCO DEMCO RESILIENT SEATED BUTTERFLY VALVE. Installation, Operation and Maintenance Manual D I S T R I B U T E D V A L V E S DEM-RSBV-IOM DEMCO RESILIENT SEATED BUTTERFLY VALVE DEMCO TABLE OF CONTENTS DEMCO RESILIENT SEATED BUTTERFLY VALVE Bill of Materials... 1 Scope... 3 Nameplate Information... 3 Storage... 3 Installation... 4 End-of-Line

More information

Fisher 657 Diaphragm Actuator Sizes and 87

Fisher 657 Diaphragm Actuator Sizes and 87 Instruction Manual 657 Actuator (30-70 and 87) Fisher 657 Diaphragm Actuator Sizes 30 70 and 87 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Installation... 3 Mounting

More information

AVK SAUDI VALVES MANUFACTURING COMPANY

AVK SAUDI VALVES MANUFACTURING COMPANY AVK SAUDI VALVES MANUFACTURING COMPANY AVK SERIES 24 - HIGH PRESSURE, WET BARREL HYDRANT FIELD MAINTENANCE AND INSTRUCTION MANUAL TABLE OF CONTENTS EXPLODED ASSEMBLY / PARTS LIST INTRODUCTION / DESCRIPTION

More information

Installation Operation Maintenance

Installation Operation Maintenance Worcester 53 / 54 Series PN 16 / 25 / 40 reduced bore ball valves Installation Operation Maintenance WCENIM0010-01 Original Instructions Copyright All rights reserved. No part of these instructions may

More information

Installation, Operation, and Maintenance Manual. Gate, Globe, and Check Valves

Installation, Operation, and Maintenance Manual. Gate, Globe, and Check Valves SMITH VALVES Installation, Operation, and Maintenance Manual Gate, Globe, and Check Valves TNC Doc EDC 303, Revision 7, Issued November 2013 TABLE OF CONTENTS 1.0 - GENERAL 2.0 - INSTALLATION 3.0 - OPERATION

More information

Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual Installation, Operation, and Maintenance Manual API 6D Piston Check Valve - IOM: Installation, Operation and Maintenance Manual 1/16 Table of Contents 1 INTRODUCTION... 3 1.1 SCOPE... 3 1.2 DISCLAIMER...

More information

CR4 Discrete Valve and Manifold Valve Repair or Replacement Procedure

CR4 Discrete Valve and Manifold Valve Repair or Replacement Procedure P/N 01-1012769 REV. F 07/18 INSTRUCTION SHEET CR4 Discrete Valve and Manifold Valve Repair or Replacement Procedure Entegris CR4 valves and manifold valves can be repaired or replaced in the event of valve

More information

METERING VALVE 2" STEM GUIDED

METERING VALVE 2 STEM GUIDED 2" STEM GUIDED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be construed

More information