KIP Solenoid Selection

Transcription

1 KIP Solenoid Selection Solenoid Selection 1/2" NPT onduit dapter Nut Housing Stop Orifice (Normally Open) Spring Loaded Top Seal oil Plunger Spring, Plunger, tn ottom Seal Guide ssembly Shading ing ( Only) ody Selecting the est Solenoid Operator for Your pplication ody Orifice (Normally losed) TU KIP Jr. ( 9) Size - iameter (inches) /1 1-5/8 Maximum MOP (psi) Vacuum Service Max. v - ody Min. v - ody Max. v - Stop Min. v - Stop Power ating.5 watts watts watts watts 10 watts Lead Wire Gauge 24 WG 20 WG/18 WG 20 WG/18 WG 18 WG 18 WG Low Wattage Operators to 1.5 Watt vailable vailable vailable vailable N/ 1/8" Ports - ody 1/4" Ports - ody 3/8" Ports - ody 4 #10-32 UN Ports - ody 1/8" NPT or 1/4" NPT Male ottom Port UL ecognized S pproved 4 Grommet Style Housing onduit Style Housing Spade Terminal Style - (Standard) 1/4" 1/4" 1/4" Spade Terminal Style - (Options) 3/1" 3/1" Yoke Style (Open rame) Side Metering ottom Metering xtended low apabilities Operator Mount Manifolds Valve Mount Manifolds iaphragm Isolated Version -5

2 KIP oils oils U V* ll standard KIP valves are supplied with a lass dry tape wound coil construction with 24" black leads, P/N (01) in the ordering system, unless otherwise specified. When using this chart below note the available housing styles and the series in which coils are available. The following chart shows all coil options readily available, for other options in OM quantities consult KIP. Non-standard voltages, leadwire lengths, other lead wire types and colors, may require minimum quantities. KIP standard voltages: 12V, 24V, 24/0, 120/0, 110/50, 220/50, 240/0. Lead wire type - WG 20 on 1 and 2 WG 18 on 1 and 2 with free standing molded coil WG 18 on 3 and oil classification - lass = 130 or 2 lass = 155 or 311 lass H = 180 or 35 Number Housing Type lass Grommet 1, 2, 3, Standard - dry tape wrapped with leads ** onduit 1, 2, 3, Standard - dry tape wrapped with leads ** Slotted 1 ree standing molded with leads ** Slotted 2, 3, ree standing molded with leads ** Yoke 2, 3 ree standing molded with leads ** onduit 1, 2, 3 Potted with leads ** Slotted 2, 3 3/1" Vertical spade ** Slotted 2, 3 1/4" Vertical spade ** Yoke 2, 3 1/4" Top spade (vailable with W option***) ** Grommet ree standing molded with leads ** onduit ree standing molded with leads ** Slotted 1/4" Vertical spade ** * or lass coils change the second digit to a 2. onsult KIP for minimum order quantities. ** or lass H coils change the second digit to a 3. onsult KIP for minimum order quantities. *** ull wave rectification -

3 KIP Numbering System KIP Part Identification Numbering (PIN) System or Valves The KIP part number provides information about every aspect of the product it represents. The first letter is an optional prefix which identifies UL recognized, oxygen or low wattage. The following numbers identify series, ports, housing style, material, valve function, orifice, seal, coil construction and coil temperature, in that order. The numerical value for each respective category represents one of multiple options. Where possible, the organization of this KIP catalog presents information in the order of the part identification number. You may use the number as a guide to finding information within the catalog. The following chart is the key to understanding the KIP Part Identification Number. OPTIONL U V PIXS (Optional) U = UL ecognized Y = Oxygen Service = Low Wattage* Watt = Low Wattage* -2.0 Watt = Low Wattage* -2.5 Watt = Low Wattage* -3.0 Watt G = iaphragm see page for ordering SIS 1 = 1 2 = 2 3 = 3 = POT 3 = 1/8" NPT Male ottom (a) 4 = 1/8" 5 = 1/4" (b) = Manifold Mount (c) = #10-32 UN 8 = 3/8" NPT (f) OY MTIL 0 = Stainless Steel 1 = rass 3 = Operator HOUSING 1 = Grommet 2 = 1/2" NPT onduit 3 = Yoke (d) 4 = Yoke w/bracket (d) = Grommet w/bracket 9 = Slotted (e) 0 = Slotted w/bracket (e) UNTION 1 = 2WN 2 = 2WNO 3 = 3WNV 4 = 3WNL 5 = 3WNO = 3WMP = 3W (a) OIL OPTIONS See page - OII 0 = 1/32" 1 = 3/4" 2 = 1/1" 3 = 5/4" 4 = 3/32" 5 = 1/8" = 5/32" = 3/1" (b) 8 = 1/4" (b) 9 = 3/8" (f) VOLTG See page - SL 01 = una 02 = luorocarbon 03 = Neoprene 05 = Low temperature una 0 = Polyurethane (2WN only) 08 = Teflon (2WN only) 12 = Neoprene W 13 = thylene Propylene (P (ood Grade) (a) = vailable in 1, 2 & 3. (b) = vailable in 3 &. (c) = vailable in 1, 2 &. (d) = vailable in 2 & 3 only and must be used with molded spade coil or free standing molded coil with lead wires. (e) = Slotted housing (used with 31 & 51 spade coil option), available in 2, 3 &. Used with molded coil 1 in 2 & 3, and 41 in 1. (f) = vailable in, 2WN only. (g) = vailable in 1 & 2 diaphragm only. Teflon and Neoprene are registered trademarks of.i. upont e Nemours o. *vailable in 1, 2 & 3 for 2-Way Normally losed, 3-Way Normally losed and 3-Way Multi-Purpose functions. -

4 KIP 2-Way Normally Open 2-Way Nomally losed 3-Way Normally Open 3-Way Normally losed (or free vent, change fifth digit from 4 to 3) 3-Way Multi- Purpose Orifice v Standard Valve ody Grommet Manifold Mount** iameter actor MOP Stainless Steel rass Valve ody-grommet (psi) ody Stop ody Stop 1/8" 1/4" 1/8" 1/4" Stainless Steel rass 1/ / / / / / / / / / / / / / / / /32 1/ /4 3/ /1 1/ /4 5/ /32 3/ /8 1/ /32 1/ /1 1/ /4 1/ /32 1/ /4 3/ /1 1/ /4 5/ /32 3/ /8 1/ /32 1/ /1 1/ /4 1/ /32 1/ /4 3/ /1 1/ /4 5/ /32 3/ /8 1/ /32 1/ /1 1/ /4 1/ Note: manifold mount 3-Way valves have a 1/4" adapter as standard. 1/8" available upon request. ** Manifold Mount valve has maximum 400 MOP rating for UL recognition. These valves are supplied with 3/8" ports

5 KIP G N Standard Valve H K M G H K M N 1.2 (41).344 (9) G-2.04 (52) (3) (48) 3.54 (90) (31) 1/8-2 #10-32 UN or 1/4-18 x 5/1 MT 1/8-2 or 1/4-18 H Operator Standard G H 1.4 (42) G-.9 (25) -.80 (20) 1.9 (4) 2.48 (3) 1-32 UN 1/8-2 or 1/4-18 G Mounting rackets racket imensions 2.13 (54) 1.9 (50).20 (5) 2.3 () 2.15 (55) 2.8 (8) Manifold Mount Valve N m n r 1.2 (41) G- 1.3 (44) (5) (82) 1/2 20 UN.31 (8) 1/8-2 or 1/4-18 M Max 40 Manifold Mount Interface 1/2-20 UN-2 x.32 MT.2 ().51 (13) NOT: is underseat connection** is overseat connection*** -33