Index. Flexcor Wire Mesh Grips K-1

Size: px

Start display at page:

Download "Index. Flexcor Wire Mesh Grips K-1"

Melvyn Eaton
6 years ago
Views:

1 Fittings available in male straight, female straight, 45 and 90 designs for fast installation in all kinds of applications. Corrosion-resistant, die cast aluminum fitting with watertight seal (Deluxe Cord ) protects connections from cable stress in damp applications. No special installation tools required. Non-corrosive, double-weave stainless steel mesh () supports the cable, absorbs stress caused by flexure and vibration, as well as controls arc of cable. Mesh readily expands for a wide range of cord diameters. CG610 Male Straight, Deluxe Cord s Index Rugged, easy-to-install and available in a wide range of sizes our Flexcor Wire Mesh, Cable-Pulling, and Cable-s are engineered to take some of the strain off of you. Device Page Number K-2, K-3 Product Description K-4 Split Lace & Rod Mesh Termination K-5 s K-6 Grips K-7 Liquid-Tight Grips K-8 s Standard-Duty, Closed Mesh K-9 s Standard-Duty, Split Lace K-10 s Standard-Duty, Split Rod K-11 s Heavy-Duty K-12 s Service & Bus Drop K-13 s Fiber Optic K-14 Pulling Grips Junior- & Light-Duty K-15 Pulling Grips Medium-Duty K-16 Pulling Grips Heavy-Duty K-17 Pulling Grips Multi-Weave K-18 Pulling Grips High Strength & Fiber Optic K-19 Pulling Grips Slack K-20 Selecting Properly Sized Pulling & s K-21, K-22 Pulling & s Strength Information K-23 K-1

2 Bus/Service Drop Liquid-Tight Conduit Grip (page K-8) Bus/Service Drop Liquid-Tight Conduit Grip (page K-8) Medium/Heavy-Duty (pages K-16, K-17) Service Drop For assistance in selecting, see pages K-21 K-23. K-2

3 High Strength Pulling Grip (page K-19) Bus Drop Deluxe Cord Grip Strain Relief AIR Heavy-Duty Underground Pulling Grip (page K-17 K-3

4 Application are used to support cable or conductor after it has been installed, pull electrical cable or conductor into place, provide strain relief at the point of wiring connections. Flexcor devices protect cables, relieve stress, and prevent cable pull-out from fittings and terminations. Product Description Available in four different attachments. Load is distributed over entire length of grip and will not injure cable. Attachments Double Eye Single Eye Offset Eye Locking Bail Eye Grip Fittings Male Straight Female Straight Male 45 Male 90 Prevents pull-out or damage to cable due to constant motion or flexing. Also for Liquid-Tight, hose and box connections. Pulling Grips Flexible Eye Rotating Eye Mesh Types Closed Mesh Split Lace Mesh Split Rod Mesh Assortment of rugged pulling grips available individually or in kits to make wire pulling easier. Product Description K-4 Available in three types and depends on availability of wire end.

5 Split Lace/Split Rod Attachments (for use where end of cable is not accessible) Split Lace Mesh Termination For Split Lace mesh termination, Flexcor single weave Split Lace grips are provided with an additional single lace, two laces are provided with each double weave Split Lace grip. Lace strands should be same material as the grip. Split Lace & Rod Mesh Termination Wrap split mesh grip around cable. Start lacing at top or bottom end of mesh. Thread lace through first two loops of split mesh and pull through until the lace is centered at this point. Lace as you would your shoe, crossing laces before lacing the next two loops Leave a space between adjoining loops approximately equal to the width of one diamond of the mesh. 3. Twist ends of lace strands together at end of grip or tie in a knot. 4. Wrap ends of lace tightly around grip. Excess lace may be cut off. Split Rod Mesh Termination For Split Rod mesh termination, a weaving rod is supplied with each grip. The open mesh passes around the rod and matches up with the open mesh from the opposite direction. Split Rod support grips are quick and easy to use and reusable. 1. Wrap split mesh grip around cable. Thread rod through the open loops in a weaving motion, using end of the rod to engage loops. 2. A steady push and twist motion is required. Use other hand to bring mesh loops together so as to weave through them. 3. To remove, pull rod out K-5 Split Mesh Termination

Straight Male Liquid-Tight Grips Description Liquid-Tight grips are woven of stainless steel mesh with zinc plated steel or malleable iron bodies and nuts for corrosion resistance.

6 Straight Male Liquid-Tight Grips Description Liquid-Tight grips are woven of stainless steel mesh with zinc plated steel or malleable iron bodies and nuts for corrosion resistance. They are used to connect liquid-tight flexible conduit to electrical enclosures to prevent conduit pullout. Each fitting is supplied with an insulated throat to provide conductor insulation and protect against damage by flexing, heat expansion and contraction. Liquid-Tight grips are recommended in the wiring of motors and any electrical enclosure where liquidtight conduit is subject to motion or strain. NOTE: Stainless steel mesh is not suitable for marine use. Straight Male 90 Male 45 Male NPT Mesh Catalog Number Catalog Number Catalog Number Size Length Liquid-Tight for Metallic Flexible Conduit STB38SF STB4538SF 3/8" 2.625" STB50SF STB9050SF STB4550SF 1/2" 3.875" STB75SF STB9075SF STB4575SF 3/4" 4.375" STB100SF STB90100SF STB45100SF 1" 5.25" STB125SF STB90125SF STB45125SF 1-1/4" 5.625" STB150SF STB90150SF 1-1/2" 5.75" STB200SF STB90200SF STB45200SF 2" 7.5" STB250SF STB45250SF 2-1/2" 9.625" STB300SF STB90300SF STB45300SF 3" " Liquid-Tight Grips K-8 90º Male 45º Male Straight Male NPT Mesh Catalog Number Size Length Liquid-Tight Grips for Non-Metallic Type A Flexible Conduit STBN38SF 3/8" 9" STBN50SF 1/2" 10" STBN75SF 3/4" 10.5" STBN100SF 1" 12" STBN125SF 1-1/4" 17" STBN150SF 1-1/2" 21.5" STBN200SF 2" 24" Straight Female Non-Metallic Straight Male

Index. Flexcor Wire Mesh Grips K-1

Index. Flexcor Wire Mesh Grips K-1 Fittings available in male straight, female straight, 45 and 90 designs for fast installation in all kinds of applications. Corrosion-resistant, die cast aluminum fitting with watertight seal (Deluxe Cord