INSTALLATION INSTRUCTIONS NEON RGB
|
|
- Maryann Richard
- 5 years ago
- Views:
Transcription
1 LLI-NCC3.7W **DANGER: Prior to installation, disconnect power at the source.** Make sure you have all components listed below: Neon 24V Non-Diming Power Supply RGB Receiver/Decoder Mounting Clips or Extrusion Page 1
2 Please read all steps before beginning the installation. DANGER, RISK OF SHOCK: Prior to installation, disconnect power at the source. These products may represent a potential shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with these instructions, local electrical codes and the National Electric Code (NEC). Do not connect directly to high voltage power ( V)! To avoid electrical shock, use only 24v hardwire or plug in power supply. Factory warranty will be void if used otherwise. Do not energize Neon when rolled up in a spool. LLI Architectural Lighting s Neon is suitable for outdoor use and damp locations (IP65). Do not use if there is any damage to the unit or to the power cord s insulation. Inspect periodically. Do not puncture, cut, shorten, or splice Neon. Consult factory at or cs@llialighting.com for custom configurations. Do not route cords or Neon through walls, doors, windows or any similar part of a building structure. Do not secure Neon or its power cord with staples, nails, or any other sharp objects that may cause damage. Mounting clips are available (sold separately). Do not install Neon closer than 6 to combustible material. Ensure applicable wires are in compliance with local codes (In-wall rated, wet-location, high temperature, etc.). Page 2
3 3 1 1/2 MINIMUM BEND DIAMETER 3 INCH DO NOT TWIST LED NEON FLOW DO NOT BEND LED NEON FLOW IN THIS WAY DO NOT BEND LED NEON FLOW IN THIS WAY Page 3
4 STEP 1 STEP 2 Remove the Neon from its package and un-roll the Neon. Measure the location where the Neon will be placed. STEP 3 STEP 4 Fasten mounting clips/channel onto mounting surface using appropriate hardware. Carefully press the Neon into the support channel or mounting clips until secure. NOTE: Do not bend the Neon tighter than a 1.5 radius (3 diameter). Page 4
5 IMPORTANT: Polarity is crucial for the operation of the Neon. Please ensure that your wiring corresponds with the polarity of the Neon. STEP 14 STEP 15 Open both wiring compartments on each end of the RGB Receiver/Decoder. STEP 16 Connect the positive (+) wire from the power supply to the positive (+) input terminal of the receiver. Connect negative (-) wire from the power supply to the negative (-) input terminal of the Receiver/Decoder. STEP 17 Connect the RGB wires from the Neon to the output terminals of the Receiver/Decoder. Connect the positive (+) wire to the positive (V+) input terminal, and connect the color wires to the corresponding color negative (-) input terminals. Connect the power supply to AC power/line voltage. Please refer to the wiring diagram of the power supply being used. Each power supply has its own specific wiring. Once connected, turn on the Neon. NOTE: Connect the positive wire from the power supply to the positive (+) wire on the Neon. Connect the negative (-) wire from the power supply to the negative wire on the Neon. Please make sure you always connect to the correct polarity. Each section is marked with a (+) for positive and a (-) for negative. If a section does not energize, you may need to check the connector or switch the wires. Page 5
6 Low Voltage Wire Gauge Chart 24V DC Voltage Drop and Wire Length (ft.) Distance Chart Power (W) 10W 20W 30W 40W 50W 60W 70W 80W 90W 100W 110W 120W Wire Gauge # # # # # Page 6
Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON
Installation Instructions for SINGLE COLOR 24V LINEAR LED NEON LLI-N2.9W Prior to installation, please confirm that you have the required system components listed below. LED Neon Flow Extrusions/Lens (Optional)
More informationINSTALLATION INSTRUCTIONS WHITE / SINGLE COLOR 24V LED TAPE
LLI-L1.5W LLI-L2.2W LLI-L2.5W LLI-L3.5W LLI-L4.4W LLI-LHE3.5W LLI-LHE4.4W LLI-LHE5.9W LLI-LTP2.5W LLI-LTP5.0W LLI-LSE3.0W LLI-LWF5.5W LLI-LC4.4W **DANGER: Prior to installation, disconnect power at the
More informationINSTALLATION INSTRUCTIONS RECESSED EXTRUSIONS WITH LED TAPE
LLI-XR-CRV LLI-XR-ELF LLI-XR-IFL LLI-XR-IGR LLI-XR-SQF LLI-XR-THF **DANGER: Prior to installation, disconnect power at the source.** Make sure you have all components listed below: LED tape 24VDC Power
More informationINSTALLATION INSTRUCTIONS SURFACE EXTRUSIONS WITH LED TAPE
LLI-XS-30D LLI-XS-60D LLI-XS-90D LLI-XS-ANG LLI-XS-AUR LLI-XS-DEP LLI-XS-DOM LLI-XS-ELT LLI-XS-FLX LLI-XS-GEN LLI-XS-GZR LLI-XS-ICN LLI-XS-SQR LLI-XS-THN LLI-XS-WID LLI-XS-ZEN **DANGER: Prior to installation,
More informationInstallation Instructions for SINGLE COLOR 12V or 24V LINEAR LED
Installation Instructions for SINGLE COLOR 12V or 24V LINEAR LED LLI-L1.5W (T300) LLI-L2.2W (TSHL2835-300) LLI-L2.5W (TSHL2835-600-2.5W) LLI-3.5W (TSHL2835-480) LLI-L4.4W (TSHL2835-600) LLI-L5.9W (TUB5630-560)
More informationInstallation Instructions for GRIPPER CONNECTOR
Installation Instructions for GRIPPER CONNECTOR LLI-GC-LL-RGB LLI-GC-LL-RGBW (12mm only) LLI-GC-LL-SC LLI-GC-LL-VW LLI-GC-LW-RGB LLI-GC-LW-RGBW (12mm only) LLI-GC-LW-SC LLI-GC-LW-VW Prior to installation,
More informationNOVA FLEX FLEXIBLE LED SOLUTIONS
DESIGN SERIES / ARCHITECTURAL LIGHTING HighCRI (90) LED ribbon light in output ranges for every application. Architecturalgrade lighting that ensures proper execution of design intentions. 50,000 DESIGN
More informationchannel damage the internal components and the weight may break the internal wiring or flexible strip.
YOU MAY NEED End cap Power adaptor Connector pin Splicing pin Connector Silicone glue Pliers Power converter Converter + surge protector Heat shrink Aluminium channel Heat gun NT cutter IMPORTANT NOTES
More informationNANOTUNE. Installation Manual
Installation Manual WARNING: DO NOT ATTEMPT TO INSTALL OR USE THE NANOLUME FIXTURE WITHOUT READING THE INSTALLATION INSTRUCTIONS AND SAFETY LABELS COMPLETELY. Failure to adhere to these instructions could
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationKompensator External Low Voltage Heating Cable System
External Low Voltage Heating Cable System LOW VOLTAGE Installation Instructions General Information Kit Contents Qty Description 1 heating cable at pre-determined length Table of Contents General Information........................
More informationWARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS
WARNING NORDIC ALUMINIUM LIGHTING TRACK SYSTEMS DO NOT solder connectors as this will prohibit the adapters circuit switch to move freely from circuit to circuit. Nordic Aluminium track adapters and accessories
More informationLEDneon flex. Features & Benefits DOT-FREE ILLUMINATION
DOT-FREE ILLUMINATION Features & Benefits Viable alternative to glass neon 220V with power converter 12V DC with constant voltage driver Seamless, dot-free illumination Up to 80% more energy efficient
More informationINSTALLATION INSTRUCTIONS For Light*Waves Flex II Kit with 300-Watt remote transformer
IMPORTANT SAFETY INSTRUCTIONS READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. THIS IS A 12-VOLT SYSTEM
More informationELECTRICAL SAFETY. Safety Training For The Non-Qualified
ELECTRICAL SAFETY Safety Training For The Non-Qualified LANGUAGE OF ELECTRICITY Electricity: Negatively Charged Particles Moving Over A Conductor Current: Movement Of Electrons Along A Conductor Ground
More informationMOUNTING SYSTEMS SPECIFICATIONS
MOUNTING SYSTEMS SPECIFICATIONS GENERAL Mounting Systems shall allow Track Systems to be fastened to or from various surfaces in a wide range of safe and approved methods. Mounting Systems shall have a
More informationAUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS
AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS The original TOMMY GATE hydraulic lift Assembling the Auxiliary Battery Box 1. Remove the cover from the auxiliary battery box by removing the two nuts and
More informationLED NEON FLEX INSTALLATI ON GUI DE
LED NEON FLEX INSTALLATI ON GUI DE F I R E F L Y L I G H T I N G. C O M. A U WHAT IS LED NEON FLEX? THE MOST VERSATILE AND SIMPLE LIGHTING SYSTEM YOU WILL EVER USE LED Neon Flex is a green friendly, safe,
More informationINSTALLATION & OPERATION MANUAL
EUKT05-RGBWW60 RGB + Warm White LED Strip Lighting System INSTALLATION & OPERATION MANUAL What s in the box? XC3-40500-RF RGB+W LED Controller w/ RF Remote Control EULSP0260-5.0 RGB+WW LED Strip Lighting
More informationBase Power Infeed Installation for Training Tables with Modular Table Power System
Base Power Infeed Installation for Training Tables with Modular Table Power System Topic Table of Contents General Safety Warnings Base Power Infeed Usage Electrical Circuits Base Power Infeed - 0 Amp
More informationFlex Tube. User guide
Flex Tube User guide CONTENTS INTRODUCTION...2 Welcome 2 Safety 2 INSTALLATION...3 Flex Tube orientation 3 Bending a Flex Tube 4 Cutting a Flex Tube 4 Connection and mounting kits 5 Feed cable kit 5 End
More informationInstallation Instructions Table of Contents
Installation Instructions Table of Contents Pre- Installation of Garage Storage Lift 2 Layout the Garage Storage Lift 3 Installing the strut Channels 3 Install the Drive Assembly 5 Install the Drive Shaft
More informationRECESSED TRACK (120V) SPECIFICATIONS
RECESSED TRACK (120V) SPECIFICATIONS GENERAL Recessed track shall be approved by the NEC for flush-mounting into ceiling or any flat surface. Recessed Track shall allow fixtures to be easily focused, switched,
More informationHPFB. Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES.
Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/ or putting undue pressure
More informationINTEGRID TRACK (120V) SPECIFICATIONS
INTEGRID TRACK (120V) SPECIFICATIONS GENERAL Integrid Track shall be a combination Track and main runner for mech - anically supporting suspended ceiling systems. Integrid Track shall allow fixtures to
More informationDL-FLEX (-UP, -UP-HO, -UP-ULTRA)
-HO -ULTRA DESCRIPTION DL-FLEX series is a unique commercial grade modular lighting system featuring 3 levels of light output with a wide range of accessories and a variety of control options. This unique
More informationRecommended Tools: Phillips Screwdriver, Flat Blade Screwdriver, 13mm and 10mm Wrench, 5/16 nut driver,
UPS-ST-120 UPSPro Outdoor UPS System Wireless Base Stations and Client Devices Surveillance Cameras Mission Critical Backup Power Remote Sensors Congratulations! on your purchase of the UPSPro Outdoor
More informationNUTP7-LED (Amber Finish) NUTP7-WLED (White Finish) 24V LED Tape Light Roll. Source: 24W Watts Per Foot CRI. 24V LED Tape Light Roll
ILLUMINATING THE FUTURE...SINCE 1989 NUTP7-LED (Amber Finish) NUTP7-WLED (White Finish) 24V LED Tape Light Roll PRODUCT DESCRIPTION Nora s very low profile, energy efficient LED tape is only 7/16" wide
More informationGEMINI HOUSING SPECIFICATIONS
GEMINI HOUSING SPECIFICATIONS GENERAL Gemini Housing shall support Track of six foot intervals. In addition, the extra compartment shall be able to be used for a multitude of elec trical or mechanical
More informationBack-Up Sensor System
Back-Up Sensor System Model No.: PKC0RE Owner s Manual and Warranty Information OFF ON 0.4m/1.3ft 0.6m/2.0ft 1.0m/3.3ft 1.2m/4.0ft 1.5m/5.0ft LEFT RIGHT Read these instructions completely before using
More informationNuheat WEATHER-READY HEAT TRACE PIPE FREEZE PROTECTION SYSTEM. Self-Regulating Heating Cable Installation Guide. UV Resistant Polyolefin Outer Jacket
Nuheat WEATHER-READY HEAT TRACE PIPE FREEZE PROTECTION SYSTEM Self-Regulating Heating Cable Installation Guide Tinned Copper Braid UV Resistant Polyolefin Outer Jacket 16 AWG Bus Wire Polyolefin Inner
More informationDoodad Tape Light & Halcyon Controller Single Colour Installation Instructions
P 1 of 4 Single Colour Installation Instructions IMPORTANT PLEASE READ BEFORE INSTALLATION Before commencing installation ensure the relevant mains supply has been safely isolated. Installation should
More informationHPNLS-HO. Installation Manual
Installation Manual WARNING: Do not lift fixture by cables. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/or putting undue pressure
More informationSURFACE TRACK (120/250V) SPECIFICATIONS
SURFACE TRACK (120/250V) SPECIFICATIONS GENERAL Lighting Track shall allow fixtures to be located anywhere along the track length. Fixtures shall be easily focused, switched, dimmed, accessorized and removed
More informationNUTP1-16LED 24V 16' Standard LED Tape Light Roll
NUTP1-16LED 24V 16' Standard LED Tape Light Roll Source: 24W LEDs PRODUCT DESCRIPTION LED Tape Light is a perfect solution for your LED linear lighting needs. This energy efficient and very low profile
More informationGeneral safety and installation information.
Read these instructions before connecting and using your PowerBright Pure Sine Power Inverters. Failure in observing this warning may result in injury to persons and damage to equipment. General safety
More informationLNT-65RGBW 3.4W IP67/IP68 COLOR-CHANGING LED STRIP
SPECIFICATION SHEET JOB NAME: LOCATION: QUOTE/REF#: LNT65RGBW is a high performance flexible LED fixture designed as a neon replacement. Suitable for indoor and outdoor applications, the LNT65RGBW can
More informationFINA SUSPENDED INSTALLATION INSTRUCTIONS
FINA SUSPENDED INSTALLATION INSTRUCTIONS 3 AC Cable Mounting (AC3) Installation... 2-4 AC Cable to Hub Mounting (AH4) Installation... 5-7 Pendant Pipe Mounting Installation... 8-9 Canopy Detail... 10-11
More informationP Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate
Fullsize Ford Van- 1992-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting kit (Figure 1 and Table 1). S-400-40 STRAP VAN MOUNTING EAR BENT BRACKET
More informationSource: 209.2LM per foot, 2.7W per foot
ILLUMINATING THE FUTURE...SINCE 1989 Type Project Catalog No. Lamp/Wattage NUTP51-W100LED9 Series 24V Continuous Hy-Brite LED Tape Light Source: 209.2LM per foot, 2.7W per foot Dimensions Max 32FT. PRODUCT
More informationNUTP1-16LED 24V 16' Standard LED Tape Light Roll Source: 24W LEDs
NUTP1-16LED 24V 16' Standard LED Tape Light Roll Source: 24W LEDs PRODUCT DESCRIPTION LED Tape Light is a perfect solution for your LED linear lighting needs. This energy efficient and very low profile
More informationEDITION : A. Description: SCALE : 100% (L4 FFL-201 ANZ) manual artwork PART NO COLOR ITEM ID. MATERIAL 50gsm recycle paper REV.
Description: EDITION : A 018331003(L4 FFL-201 ANZ) manual artwork SCALE : 100% PART NO ITEM ID REV. 961001550 MODEL NO 018331003 COLOR Black CM00166845 DIELINE 01 SIZE unfold:280mmx203mm; fold:70mmx26mm(+/-2mm)
More informationNICHE-HV. Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES.
Installation Manual WARNING: DO NOT LIFT FIXTURE BY CABLES. This could result in permanent damage to both the fixture and the cables. Damage resulting from grasping cables and/ or putting undue pressure
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More informationt each side - о Т-49А S G1'dual drlve "' and Original Series Mounting Instructions
G1'dual drlve "' and Original Series Mounting Instructions Service, Utility, Flatbed, Stake and Van Body Preparing the Gate 1. Measure the body opening, the overall width, and the maximum bed height of
More informationInstallation Instructions. Power Connector (#LLED9100-F-PC-180D)
1 of 10 Overview End Cap U-Channel (#-UC) Mounting Clip (#-MC) End View 0.84 Flexible 0.44 Power Connector (#-PC-180D) IMPORTNT VERIFY CORRECT LUMINIRE WS RECEIVED WITH CORRECT COLOR TEMPERTURE ND VOLTGE
More informationand Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks present T-420 BOLT-ON GUSSET PART#5257
and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks- 2004-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket
More informationWARNING. Tools: 1. Wire Strippers 2. Screw Driver or Rivet Gun 3. Tape Measure 4. Drill. Components: AWG (0.82mm) Wire-UL Approved
Tools: 1. Wire Strippers 2. Screw Driver or Rivet Gun 3. Tape Measure 4. Drill Components: 1. 1 AWG (0.2mm) Wire-UL Approved *Under certain conditions, a heavier gauge wire may be necessary. 2. General
More informationInstallation Instructions
1 of 12 Overview Clear Lens Cover (#-LC) Power Connector (#LLED8500-PC) RGB StripLite (#LLED8500) End View.73 Extrusion (#) 1.62 End Cap (#-EC) 8 Maximum extrusion and lens length (Dry Location field cuttable)
More informationand Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks Fleetside 4-door Chevy & GMC Trucks T-100
r ve and Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks - 1960-1987 Fleetside 4-door Chevy & GMC Trucks - 1988-1991 Preparing the Gate 1. Remove the mounting hardware which
More informationCustom LitePad Handling & Mounting Guide
Custom LitePad Handling & Mounting Guide Low profile light emitting panel for backlighting or area lighting, available in standard or custom sizes and fixed white, tunable white or RGB configurations,
More informationSloanLED THINLED. Constant Current. Installation Guide
SloanLED THINLED Constant Current Installation Guide Product covered in this guide: ThinLED CC: Part Number Description 701228-18-A Amber ThinLED Constant Current 701228-18-B Blue ThinLED Constant Current
More informationSource: 81.68LM per foot, 1.3 W per foot
ILLUMINATING THE FUTURE...SINCE 1989 Type Project Catalog No. Lamp/Wattage NUTP71-W100LED9 Series 24V Continuous Standard LED Tape Light Source: 81.68LM per foot, 1.3 W per foot Dimensions PRODUCT DESCRIPTION
More informationMASTERsine Inverter PXA Series Installation Guide
Backup Power System Expert TM MASTERsine Inverter PXA Series Installation Guide Important Safety Instructions IMPORTANT: Read and save this Installation Guide for future reference. This chapter contains
More informationSURFACE/CEILING & SUSPENDED MOUNT INSTALLATION
SURFE/CEILING & SUSPENDED MOUNT INSTALLATION E477827 E477827 APPLICATION NL luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, corrosion, vibration and rough
More informationDURATAPE TM HO INDOOR RGB+W
PROJECT MODEL(S) TYPE High Output RGB+W Tapelight High output indoor RGB and RGB+W LED Tapelight strip emits sharp, color changing effects in indoor niche, cove and architectural decorative applications.
More informationLED STRIP LIGHTING KIT EUKT04 WW30
LED STRIP LIGHTING KIT EUKT04 WW30 This kit comes complete with everything you will need to light up your project. It includes a deluxe LED dimmer controller, a mated AC/DC power supply, 16 4 of LED strip
More informationNUTP4-LED/4 12V 4" Standard LED Tape Light Section Source: 0.5W LEDs
NUTP4-LED/4 12V Standard LED Tape Light Section Source: 0.5W LEDs PRODUCT DESCRIPTION LED Tape Light is a perfect solution for your LED linear lighting needs. This energy efficient and very low profile
More informationThe LED Driver Expert
Power Unit Installation Instructions 1) Installation of the series power unit requires the proper connection of both the AC wires to the AC facility power, and the DC wires to the LED lighting system.
More informationC Power Connection Kit
1548-4000C Power Connection Kit For use with Dekoron 2700 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4000C electrical connection kit distirbuted by Heat-Line is
More informationSPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER. Read entire instructions thoroughly before starting. INSTALLATION INSTRUCTIONS TOOLS REQUIRED:
Read entire instructions thoroughly before starting. TOOLS REQUIRED: SPEED CONTROL 4 AND 6 CYL. JEEP WRANGLER INSTALLATION INSTRUCTIONS Complete socket set Phillips screwdriver Torx drivers Wire strippers/cutters
More informationPower Connection Kit installation instructions
Operating instructions & Parts Manual ET00 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and
More informationNUTP7-16LED 24V 16' Damp Label Standard LED Tape Light Roll Source: 24W Watts Per Foot
NUTP7-16LED 24V 16' Damp Label Standard LED Tape Light Roll Source: 24W - 1.5 Watts Per Foot PRODUCT DESCRIPTION LED Tape Light is a perfect solution for your LED linear lighting needs. This energy efficient
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More information(31 ) ZEON CONTROL PACK RELOCATION KIT
ORIGINAL INSTRUCTIONS SYMBOL INDEX (31 ) ZEON CONTROL PACK RELOCATION KIT SYMBOL EXPLANATION Read All Product Literature SYMBOL EXPLANATION Always Wear Leather Gloves INSTALLATION GUIDE Always Wear Hearing
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.
Installation Instructions 2RTLEDR/2RTLEDRT Relight Assembly READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION. IMPORTANT SAFETY INSTRUCTIONS WARNING:
More informationAcme Conduit Entry. String Combiner/Pass-Through. FOR PHOTOVOLTAIC INSTALLATION Installation Manual
Acme Conduit Entry String Combiner/Pass-Through FOR PHOTOVOLTAIC INSTALLATION Installation Manual Table of Contents Important Safety Instructions -----------------------------------------------------------------------------------------------------------
More informationPDX and PX Retrofit Series
UNIQUE LIGHTING SOLUTIONS PDX and PX Retrofit Series PDX1-1-12-XX PX1-1-12-X-X-XX-65 RETROFIT INSTALLATION GUIDE PDX and PX Series Retrofit WARNING -Retrofit installation must only be performed by a licensed
More informationCantilever Series Mounting Instructions Fullsize Sprinter Van (US) All except WB (AA) present
Fullsize Sprinter Van (US) All except 3500 144 WB (AA)- 2007-present Preparing the Gate 1. Remove the platform, mounting kit, license plate assembly, and bridge assemblies, which are banded to the main
More informationPRO-Tect Pipe Freeze Protection Self-Regulating Heating Cable Install Manual (PT-Series)
PRO-Tect Pipe Freeze Protection Self-Regulating Heating Cable Install Manual () Free Design Service 24/7 Installation Support (800) 875-5285 www.warmlyyours.com Assembly Tools Needed Utility knife Wire
More informationRibbonFlex Pro LED Accent Lighting White LED Tape Light. Welcome to RibbonFlex Pro LED Tape Lighting. Notes:
RibbonFlex Pro LED Accent Lighting White LED Tape Light 30 White LEDs per meter (9 LEDs per foot) Model # RF3528030 rev 01.14 Welcome to RibbonFlex Pro LED Tape Lighting Ultra thin and flexible, RibbonFlex
More informationInstallation Instructions: HYPERION R-Lite SYSTEM
Installation Instructions: HYPERION R-Lite SYSTEM READ THIS MANUAL BEFORE PROCEEDING WITH THE INSTALLATION. FAILURE TO FOLLOW THE INSTALLATION INSTRUCTIONS WILL VOID YOUR WARRANTY! INSTALLATION TIPS Read
More informationREAR ROOF SPEAKER KIT
REAR ROOF SPEAKER KIT P/N 2882876 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationCord Operated Curtain Track Systems
Cord Operated Curtain Track Systems Application Chart Specification Weight Range Applications Single Stack Pair Stack Multiple Stack Asymetric Profile Profile Number Dimensions in mm Gliding Channel (mm)
More informationDURATAPE TM HO OUTDOOR RGB+W
PROJECT MODEL(S) TYPE High Output RGB+W Tapelight High output outdoor RGB LED Tapelight strip emits sharp, color changing effects in outdoor niche, cove and architectural decorative applications. Key Features
More informationSection 8 Stab-lok Circuit Breakers
Section 8 Stab-lok Circuit Breakers Stab-lok easier to work with and faster to install Stab-lok breakers are fully interchangeable with all past breakers and deliver the same proven quality. The unique
More informationInstallation Guide for EcoBrite EndLite LED Light Fixtures
Installation Guide for EcoBrite EndLite LED Light Fixtures BEFORE YOU BEGIN INSTALLATION Read these instructions carefully. Failure to follow these instructions will invalidate the warranty on this product.
More informationT-52. r ve Pickup Lift Mounting Instructions Chevy / GMC- Colorado/ Canyon: 2015-present. Preparing the Gate. Installing the Bolt-on Gussets
Chevy / GMC- Colorado/ Canyon: 2015-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure 1 and Table 1). LEFT BRACKET (RIGHT
More informationNANO MIX. Installation Manual
Installation Manual WARNING: DO NOT ATTEMPT TO INSTALL OR USE THE NANOLUME FIXTURE WITHOUT READING THE INSTALLATION INSTRUCTIONS AND SAFETY LABELS COMPLETELY. Failure to adhere to these instructions could
More informationDURATAPE TM HO INDOOR RGB+W
PROJECT MODEL(S) TYPE DURATAPE TM HO High Output RGB+W Tapelight High output indoor RGB and RGB+W LED Tapelight strip emits sharp, color changing effects in indoor niche, cove and architectural decorative
More informationInstallation Instructions MX-5 Dual Air Horns
440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com Tools required: Phillips screwdriver, 8mm, 10mm and 21mm sockets, 8mm and 10mm combination wrenches,
More informationDURATAPE TM RGB IP66 OUTDOOR
Key Features Flexible flat conductor strip with High Output Red 625nm, Green: 520nm, Blue: 465nm LEDs, RGB colors Ideal for exterior cove, under-counter/cabinet, lighting accents Complete with encased
More informationLED estrip. Linear Lighting. Features. Specifications. Applications. Colour Specifications. Product Codes
Linear Lighting LED estrip LED estrip is our most versatile linear lighting product. Now with 3014 type LEDs, LED estrip is brighter and better than ever! DIMMABLE Features 40,000 hours life Safe low voltage
More informationHARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM. Parts List and Installation Instructions CAUTION
May 1, 2018 Lit. No. 92991, Rev. 00 HARNESS KIT 3 PORT ISOLATION MODULE LIGHT SYSTEM Parts List and Installation Instructions Read this document before installing the snowplow. See your sales outlet/website
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
LIGHTPATH SERIES LOW LEVEL FULLY RECESSED LED EMERGENCY LIGHT 1. 2. 3. 4. 5. 6. 7. 8. INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More informationWARNING/AVERTISSEMENT. Coupez l alimentation électrique à la boîte de fusibles ou au disjoncteur avant servicing or installing product.
Tetra Contour LS LED Lighting System GEXNLBL-1, GEXNLGL-1, GEXNLRD-1, GEXNL65-1, GEXNL32-1 Installation Guide 24 Volt BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT
More informationNUTP11 RGBW Series RGBW LED Tape Light (Color Changing) Source: 5W Per Foot LED
ILLUMINATING THE FUTURE...SINCE 1989 Type Project Catalog No. Lamp/Wattage NUTP11 RGBW Series RGBW LED Tape Light (Color Changing) Source: 5W Per Foot LED PRODUCT DESCRIPTION Nora's RGBW tape light has
More informationPower Connection Kit Installation Instructions. Terminator DP-M for use with TEK and HTEK series constant watt heating cables
Power Connection Kit Installation Instructions Terminator DP-M for use with TEK and HTEK series constant watt heating cables For Power Connection (1 Cable), In-Line Splice Connection, or End Termination
More informationInstallation Instructions. Power Connector (#LLED8300-PC) End View Electrical cords
1 of 13 Overview Frosted Lens Cover (#-LF) LED StripLite (#LLED8300) Power Connector (#LLED8300-PC) End View.73 Extrusion (#) 1.62 End Cap (#-EC) 8 Maximum extrusion and lens length (Dry Location field
More informationSLIMFLEX LED Tape Lighting
1 SLIMFLEX LED Tape Lighting Installation Guide BEFORE YOU BEGIN, READ INSTALLATION INSTRUCTIONS THOROUGHLY Install in accordance with the National Electric Code and local regulations This product is intended
More informationMULTI FUNCTION POWER PAK PLUS
MULTI FUNCTION JUMP START UP TO V8 PETROL & DIESEL 600A PEAK CURRENT RECHARGE USB POWER TOOLS TABLETS LAPTOPS MOBILE PHONES RECHARGE DEVICES ON-SITE VEHICLE JUMP STARTER KP1404 ED2 (June 15) Table of Contents
More informationChapter 8 Interior Wiring and Lighting
Chapter 8 Interior Wiring and Lighting Review Questions 1. What tool if any, is used to remove a fuse that is to be replaced? 1. Pliers 2. Screwdriver 3. Fuse puller 4. None 2. OSHA has established specific
More informationInstallation Instructions .59 CALIFORNIA ACCENT LIGHTING, INC.
1 of 13 Overview Frosted Lens Cover (#-LF) Power Connector (#LLED8300-PC) LED StripLite (#LLED8300).80 6.5 3.9 or 6.5 6.5 increments up to max run ± 0.125 cutting tolerance Extrusion (#).59 6.5 (2.5W)
More information30,000mWh LITHIUM-POLYMER CAR JUMP STARTER USER S MANUAL PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION
Lithium Battery Disposal: This product contains a lithium battery. A lithium battery should not be thrown away in the trash. Please dispose of the battery at an authorized disposal or recycle center. Check
More informationINSTALLATION INSTRUCTIONS
TM WEIGHTLIFTER Tailgates By THIEMAN TWL 125, 16, 20 INSTALLATION INSTRUCTIONS! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS MANUAL BEFORE OPERATING THE EQUIPMENT. NTEA T
More informationSeries 500. Liquid Level Transmitters. Instruction Manual
Series 500 Liquid Level Transmitters Instruction Manual Contents Section Content Page 1 Introduction 1.1 General Overview 3 1.2 Mounting Options 3 2 Installation Notes 2.1 Transmitters 4 2.1.1 Model 510
More informationLUXLINEAR LOW 1707 SLEEKER ILLUMINATION MECHANICAL. Indoor/Dry Location Series
SLEEKER ILLUMINATION Our LUXLINEAR Low Profile 1707 LED light tubes is specially designed to fit into and illuminate slimmer, compact fixtures and applications. The profile s shorter height provides a
More informationand Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD HD & 3500HD BOLT-ON GUSSET
r ve and Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD 1999-2007 2500HD & 3500HD 2000-2007 Preparing the Gate 1. Remove the mounting hardware which is banded
More information14", 18" & 24" Fiberglass Turbo Fans Installation & Operator s Instruction Manual
14", 18" & 24" Fiberglass Turbo Fans Installation & Operator s Instruction Manual 09484:09#52
More informationALTITUDE ARMS AND CANOPY
INSTALLATION MANUAL ALTITUDE ARMS AND CANOPY RV THIS MANUAL PROVIDES INSTRUCTIONS FOR THE BASIC INSTALLATION OF THE AWNING. Read this manual before installing or using this product. Failure to follow the
More information