INSTRUCTIONS 360 Y-DROP
|
|
- Brandon Wilkins
- 5 years ago
- Views:
Transcription
1 INSTRUCTIONS 60 Y-DROP
2 INSTRUCTIONS 60 Y-DROP RECOMMENDED TOOLS Ratchet wrench with /" and 9/6" deep well sockets /8" -point socket /" and 9/6" combination wrenches Impact driver # Philips screwdriver (for the shield installation) INTRODUCTION Before beginning, it s important to know where each mounting bracket fits relative to the row spacing involved. The 60 Y-DROP unit should be precisely centered on the machine, as this is critical to the assembly of the system to the sprayer and for mounting the system to your sprayer boom. There are, however, many boom variations among all sprayer models. Your sprayer may not be identical to the model in the following steps of the guide, and the pictures may not exactly reflect your model. While these steps will help you install most of your 60 Y-DROP system, you may need to custom-fit some components with your particular boom. QUESTIONS Call our Product Support team at
3 I. ESTABLISH DROP LOCATIONS Figures and Step Locate the center of the machine and identify the location of all the drops. On the sprayer boom, mark where each riser mount will be located. This will ensure that the extension tubes will not interfere with the riser mounts. Figure Figure Step Starting at the wing fold pivot pin on the primary boom, measure and mark points at ", 68", 0"; 0" and 57" (all measurements are ±5"). Repeat for the other primary boom. Figure 57" 0" 0" 68" " Figure
4 II. INSTALL PRIMARY BOOM SPRAYER MOUNT PACKAGE Figure Step With the thread pointing down, install Step square U-bolt () on the top of the OEM primary boom. Install bracket assembly () and flange lock nut (). Hardware Kit D Figure Repeat Steps and for the other OEM mount bracket. Step Install extension tube (). Repeat Steps - for the remaining mounting positions on the primary booms. Figure 5 Step Install boom bracket () onto extension tube (). Figure 5
5 III. INSTALL CENTER SECTION EXTENSION TUBE Figures 6 and 7 Step Set front and rear extension tube brackets () on top of OEM center section boom support. Step Install 6" plate () using /" x /8" flange bolt () and flange nut (5). Step Install extension tube (). Repeat Steps - for the other center section extension tube assembly. Figure 6 Figure 8 Step Install stainless steel set screw and jam nut assembly (). 5 Step 5 Install boom bracket (). Step 6 Install stop bolts () at both the front and the rear of the extension tube. Hardware Kit D Figure 7 Figure 8 5
6 IV. INSTALL 60 Y-DROP BOOM Figure 9 Step Assemble 5' boom sections () utilizing 8" boom connectors () and the supplied hardware. Hardware Bag CC Step Step Repeat Step as needed in order to assemble the entire 60 Y-DROP boom. Set the 60 Y-DROP boom assembly onto boom bracket (). Figure 9 Repeat Steps - for the remaining boom assemblies. CAUTION: The 60 Y-DROP boom assembly may weigh up to 50 lbs. (68 kg). Exercise caution and enlist help for this process. Figure 0 Step In order to span the full length of the center section 60 Y-DROP boom, you will need to cut and drill one of the 5' boom sections to '. Mount this ' section between two full 5' boom sections. Drill a 7/6" through hole centered " from the outside edge. Figures and Step 5 Install square U-bolt (), the 5/6" extra thick washers, and the 5/6" nuts over the 60 Y-DROP boom (). Hardware Kit A Figure 0 Figure Step 6 Step 7 Install stop bolt () at the both the front and the rear of the extension tube. Repeat for remaining stop bolts. Hardware Kit B Install stainless steel set screw and jam nut assembly (). See Figure for detail. Repeat for the remaining mount assemblies on the primary boom. Figure 6
7 V. INSTALL RISER MOUNTS Figure Step Install riser mount () using the square U-bolts () and the extra thick washer and nylock nut. Repeat for the remaining riser mounts. Hardware Kit C Figure Figure may show more or fewer riser mounts than your installation. The alignment and quantity of the riser mounts will depend on your row spacing. Figure Figure 5 Step Install riser tube assembly () into the riser mount (). Step Install pin (). Repeat Steps and for the remaining riser tube assemblies. Figure Figure 5 7
8 VI. INSTALL SHIELDS AND RISER HOSES Figure 6 Step Install shield () onto riser tube (). Figure 7 Step Install base unit () onto riser tube (). Figure 8 Step Figure 9 Step Assemble drag hoses () to Y-DROP base and secure with hose clamps (). Note the orientation of the drag hose clamps. The tails should point inward. Figure 6 Figure 7 Figure 8 Figure 9 8
9 VI. INSTALL SHIELDS AND RISER HOSES (continued) Figure 0 CAUTION: Do NOT use a drill or impact driver for Steps 5 and 6. Step 5 Install two ½" screws (). Step 6 Install two ¾" screws (). Step 7 Install rubber washer () into the Y. Figure 0 Figure Step 8 Figure Step 9 Install riser hose assembly () into the Y. Route riser hose assembly () as shown in Figure. Step 0 Install the riser hose assembly to the OEM nozzle body. Figure Step Use equally spaced plastic ties to secure the riser hose assembly. Repeat Steps - for the remaining 60 Y-DROP Shields. Figure INSTALLATION COMPLETE. All other trademarks are the property of 60 Yield Center, its affiliates and/or its licensors Yield Center. All rights reserved. YCG600-
INSTRUCTIONS 360 Y-DROP
INSTRUCTIONS 60 Y-DROP INSTRUCTIONS 60 Y-DROP INTRODUCTION Before beginning, it s important to know where each mounting bracket fits relative to the row spacing involved. The 60 Y-DROP unit should be precisely
More informationINSTRUCTIONS 360 Y-DROP
INSTRUCTIONS 60 Y-DROP JOHN DEERE 60 60 Y-DROP REGISTRATION Please visit productregistration.60yieldcenter.com to complete the product registration for your 60 Y-DROP so we can better support our products
More informationINSTRUCTIONS 360 Y-DROP
INSTRUCTIONS 60 Y-DROP 60 Y-DROP REGISTRATION Please visit productregistration.60yieldcenter.com to complete the product registration for your 60 Y-DROP so we can better support our products from day one
More informationINSTRUCTIONS 360 Y-DROP
INSTRUCTIONS 60 Y-DROP 60 Y-DROP REGISTRATION Please visit productregistration.60yieldcenter.com to complete the product registration for your 60 Y-DROP so we can better support our products from day one
More informationINSTRUCTIONS 360 Y-DROP
INSTRUCTIONS 0 Y-DROP 0 Y-DROP REGISTRATION Please visit productregistration.0yieldcenter.com to complete the product registration for your 0 Y-DROP so we can better support our products from day one and
More informationINSTRUCTIONS 360 Y-DROP
INSTRUCTIONS 60 Y-DROP 60 Y-DROP REGISTRATION Please visit productregistration.60yieldcenter.com to complete the product registration for your 60 Y-DROP so we can better support our products from day one
More informationINSTALLATION INSTRUCTIONS ALL JOHN DEERE SYSTEMS
2 3 6 7 1 REAR 4 5 HELPFUL TOOLS Drill and Drill Bit for 3/8 Bolt 3/8 Ratchet with 9/16 Socket NEED HELP? Call our Product Support team at 888-512-4890. STEP 1 PREPARE BASE UNIT Slide the boom height base
More information360 SPRINT INSTALLATION INSTRUCTIONS JOHN DEERE GATOR 835 AND YIELDCENTER.COM V3
3 6 0 S P R I N T 360 SPRINT INSTALLATION INSTRUCTIONS JOHN DEERE GATOR 835 AND 865 360YIELDCENTER.COM 3.26.19 V3 TABLE OF CONTENTS PARTS OVERVIEW...PAGE 3 STEP 1 REMOVE GATOR BED...PAGE 4 STEP 2 INSTALL
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationINSTALLATION GUIDE CARGO BARRIER CURRENT FORD UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE CARGO BARRIER 0 - CURRENT FORD UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD BARRIER SYSTEM B00 BARRIER B7 HARDWARE/WING KIT I. Refer
More information360 SPRINT INSTALLATION INSTRUCTIONS JOHN DEERE GATOR 825 AND YIELDCENTER.COM V4
3 6 0 S P R I N T 360 SPRINT INSTALLATION INSTRUCTIONS JOHN DEERE GATOR 825 AND 855 360YIELDCENTER.COM 4.12.19 V4 TABLE OF CONTENTS PARTS OVERVIEW...PAGE 3 STEP 1 REMOVE GATOR BED...PAGE 4 STEP 2 INSTALL
More informationInstallation Instructions for Foam Marker ZMAX
2017 Installation Instructions for Foam Marker ZMAX We appreciate your purchase of L.T. Rich s Product. Please Verify Contents before beginning installation. JLD;AES L.T.RICH 5/2/2017 SHIPPING CONTENTS...
More informationIllustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN 55060
Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN 55060 Great Plains Part # 891-653C (Gandy Part #62270) Mount & Deflector Package For Great Plains Turbo-Max 24/30 Ft Models 2400 (24-Ft)
More informationInstallation Instructions for Foam Marker INTERMEDIATE also applies: JR, JR36
2017 Installation Instructions for Foam Marker INTERMEDIATE also applies: JR, JR36 We appreciate your purchase of L.T. Rich s Product. Please Verify Contents before beginning installation. JLD;AES L.T.RICH
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationColor Applicability/Trim Level. Hardware Bag Contents Item # Quantity Reqd. Description
Document # 2291 (TMS) Posted 1/30/04 SCION xb 2004-2005 FOG LIGHT Section I Installation Preparation Part Number: 08590-52820 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
Installation Instructions SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other
More informationOperator's Manual VERSA Compact Tiller and Cultivator. ILLUSTRATED PARTS BREAKDOWN Handle Bar Assembly
ILLUSTRATED PARTS BREAKDOWN Handle Bar Assembly 4 3 2 7 5 6 7 8 6 4 2 3 0 9 7 8 4, 5 9 33 2 20 8 8 30,32 30,3 30 34 35 28 29 22 23 27 24 23 7 25 8 8 8 26-866-373-9665 3833 GRIP IN KNOB TEXTURED 2 2 23548
More informationASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS VEHICLE MOUNT KIT 99101087 AND VEHICLE CENTER MEMBER For 26 Series: 99100890 TO FIT 2009 & Later FORD F150 4x4 (without EcoBoost V6) 2011 & Later FORD F150 4x4 (with
More informationParts and tools needed for installation- Cleaning and Painting -
Thank you for the purchase of our JK Front Trail Doors. We have made these from 6061-T6 aluminum and reinforced them with stiffeners at the top that double as a comfortable armrest and support for Rugged
More information2010 Current Ford Raptor Lower Control Arm Installation Instructions
PREPARATION 2010 Current Ford Raptor Lower Control Arm Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We
More informationPart Numbers: TTU-BGP14 & TTU-BGB14
Date: 10.14.2015 TOYOTA TUNDRA 2014-17 Billet Grille Part Numbers: TTU-BGP14 & TTU-BGB14 Grille Hardware Bag Contents Item # Quantity. Description 1 6 U-Nuts 2 8 #10 Screws 3 2 #8 Screws 4 2 2 Flange Brackets
More informationLIFT-506 BMF Lift Kit Club Car DS Gas & Electric Installation Instructions
LIFT-506 BMF Lift Kit Club Car DS Gas & Electric 2003.5-09 Installation Instructions Contents of LIFT-506 Club Car DS BMF Lift Kit: a (1 ea.) BMF Front Suspension b (1 ea.) Driver Side Upper A-Arm c (1
More informationTJ 231/241 CABLE SHIFTER
KIT CONSISTS OF: # Qty Part No. Description P.O. Box 247, 4320 Aerotech Center Way PAGE 1 OF 10 Page Rev. Date: 08-29-16 1 1 300474 WASHER-RUBBER YOKE SEAL 32 SPLINE 2 1 300476 NUT- 7/8"-20 FLANGE LOCKNUT
More informationSCION xa 2004 FOG LIGHT Section I Installation Preparation. Part Number: General Applicability
Section I Installation Preparation Part Number: 81025 52080 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Assembly, RH 2 1 Assembly, LH 3 1 Switch, 4 1 Relay, 5
More informationSpray Height Controller
Spray Height Controller JD10 John Deere (4930) with Proportional Main Lift Installation Manual Printed in Canada Copyright 2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-JD10-INST Rev G (John
More informationWheel Angle Sensor Kit Installation
Wheel Angle Sensor Kit Installation Item Component Part Number Qty 1. Bracket Kit, WAS 200-0540-01 1 2. WAS Assembly 200-0468-01 1 3. Instruction Guide 602-0390-01 1 602-0390-01 REV A 2014-02 Overview
More information4WD FORD F150 BRONCO 4 OR 6 SERIES II RADIUS ARM SYSTEM
BOX KIT # 63000 4WD 81-96 FORD F150 BRONCO 4 OR 6 SERIES II RADIUS ARM SYSTEM INTRODUCTION Installation requires two professional mechanics. Be sure the vehicle is in excellent working condition-repair
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
AUTOMOTIVE PRODUCTS, INC. INSTRUCTIONS INSTRUCCIONES CONSIGNES APPLICATION: 2013-UP FORD ESCAPE APP PART # 28-21010, 28-21015 STYLIZED RUNNING BOARD ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS
More informationPlease take time to read and understand these installation instructions.
2014- Current C7 Corvette Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service center or professional
More informationConflicts. Toyota Avalon Interior Light Upgrade. Part Number Accesory Code: IL2. Color Applicability/Trim Level.
Toyota Avalon 2011 - Interior Light Upgrade Part Number 00016-00095 Accesory Code: IL2 Conflicts Kit Contents Item # Quantity Reqd. Description 1 1 Y Adapter 2 1 Wire harness 3 1 Hardware Kit 4 2 White
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE PURCHASER.
Product Number: SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information.
More informationSpray Height Controller
Spray Height Controller JD06 John Deere (4920) Installation Manual Printed in Canada Copyright 2009 by NORAC Systems International Inc. Reorder P/N: UC5-BC-JD06-INST Rev F (John Deere 4920) NOTICE: NORAC
More informationInstallation Manual, Usage Tips, & Warranty Information
Installation Manual, Usage Tips, & Warranty Information Table of Contents 1. Bill of Materials page 2 2. Exploded View of RAIL ASSEMBLY page 2 3. Hardware Pictures page 3 4. Installation: Steps 1 through
More informationTOYOTA RAV RUNNING BOARD
TOYOTA RAV4 2013 - RUNNING BOARD Part Number: 00016-42020 Accessory Code:TR1 Conflicts Mudguard Kit Contents Item # Quantity Reqd. Description 1 1 LH Board Assembly 2 1 RH Board Assembly 3 1 LH Rear Mounting
More informationDODGE Ram 2500/3500 Mesh Grille
921701510 DODGE 2013-18 Ram 2500/3500 Mesh Grille Thank you for choosing Rough Country for all your lighting needs. Please read instructions before beginning installation. Check the kit hardware against
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS STYLIZED RUNNING BOARD APPLICATION: 2011-2016 Ford Explorer PART NUMBER: 28-21170, 28-21175 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 2 RUNNING BOARDS 13MM
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 2577 Combines Case 2588 Combines Accuguide Ready PN: 602-0233-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions
More informationArctic Cat Wildcat Cab kit* Caution: Before using this product, read this manual and follow all safety instructions.
Owner s Manual Model: Arctic Cat Wildcat Caution: Before using this product, read this manual and follow all safety instructions. Arctic Cat Wildcat Cab kit* Safety Instructions Kit Contents Tool Requirement
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS APPLICATION: DODGE CHARGER POLICE PUSH BAR (2011 & UP) APP PART # 36-2035 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 PUSH BAR ASSEMBLY RATCHET 2,3 2
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 3.5 CONTOUR BULL BAR AUTOMOTIVE PRODUCTS, APPLICATION: 0-06 Chevrolet Silverado 500 PART NUMBER: 3-3000, 3-3005, 3-3005T, 3-3090, 3-3095, 3-3095T ITEM QUANTITY DESCRIPTION TOOLS
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More informationTerms and conditions of use:
Terms and conditions of use: Berk Technology or any of its affiliates will not be held liable for any and all of the costs involved with use, installation, removal, inconvenience, or any other such associated
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationInstallation Manual. For. Hi-Speed Alumavator / Platinum Vertical Boat Lifts
Installation Manual For Hi-Speed Alumavator / Platinum Vertical Boat Lifts Page 2 Safety Precautions 1. Your boat lift is a heavy duty piece of equipment. It is important that all persons that may operate
More informationGM Chevy 1500 Mesh Grille
921701940 GM 2007-13 Chevy 1500 Mesh Grille Thank you for choosing Rough Country for all your lighting needs. Please read instructions before beginning installation. Check the kit hardware against the
More informationTOYOTA AVALON INTERIOR LIGHT UPGRADE Section TOYOTA II - Installation AVALON Procedures
TOYOTA AVALON 2005 - INTERIOR LIGHT UPGRADE Section TOYOTA II - Installation AVALON Procedures 2007 Base Toyota Illumination Kit Part Number: 00016-00060 Accessory Code: IL1 Kit Contents Item # Quantity
More informationRT1 SLIP-ON EXHAUST HONDA CBR600RR REV. A
08-50-43733 REV. A PARTS INCLUDED Ref. Part Number Description Qty 1) 00-200-00064 Slip-on S-bend Assembly 1 2) 00-200-00088 RT1 Aluminum Muffler Assembly 1 3) 03-46-43058 Muffler Mounting Strap 1 4) 07-27-42566
More informationProduct Description. Product Numbers. Warning/Caution Notations. Required Tools. Wiring. Prerequisites
Document No. 155-302N VE 598 Electronic Flowrite Valve Field Assembly Product Description The VE 598 Electronic Valve Assemblies consist of an electronic actuator, linkage kit, and a valve body assembly.
More informationAssembly Instructions for A, A, A, & A
Update Instructions Yield-Pro 1225/1625 Planter Used with: Yield-Pro 1225 Planter Yield-Pro 1625 Planter General Information! When you see this symbol, the subsequent instructions and warnings are serious
More informationToyota 4RUNNER With/MR Overhead Video
Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:
More informationISOBUS Down Force Hydraulics Kinze
Important Notices Please carefully follow these step-by-step instructions. If you have questions, contact at 515-232-5363 x 1. Direction words (LEFT and RIGHT) are commonly used when describing an installation
More informationInstallation Manual. For. Trident Boat Lifts
Installation Manual For Trident Boat Lifts Page 2 Safety Precautions 1. Your boat lift is a heavy duty piece of equipment. It is important that all persons that may operate this unit have read and understood
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS OUTLAW REAR BUMPER APPLICATION: 2016-2018 Chevrolet Silverado 1500 PART NUMBER: 58-81005 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 REAR BUMPER 18MM WRENCH 2 4 SENSOR
More informationPart Number: TTU-BGB14-DRL TTU-BGP14-DRL
11/15/16 TOYOTA TUNDRA 2014-17 Billet Grille w/led DRL Part Number: TTU-BGB14-DRL TTU-BGP14-DRL Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 User Card 5 2 Hardware
More informationInstallation Guide for Rough Country 30 in. Chrome Series LED Light Bar w/ Hood Mounting Brackets
Installation Guide for Rough Country 30 in. Chrome Series LED Light Bar w/ Hood Mounting Brackets Installation Time: 1 Hour Tools Required Trim removal tool (plastic or wood to prevent scratches on the
More informationLIFT Drop Spindle Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions
LIFT-107 6 Drop Spindle Lift Kit E-Z-Go RXV Gas or Electric Installation Instructions Contents of LIFT-107 E-Z-Go RXV Drop Spindle Lift Kit: a (1 ea.) Driver Side Spindle b (1 ea.) Passenger Side Spindle
More informationFLEXI-COIL 67 Series (1999+) Installation Manual FC1
FC1 FLEXI-COIL 67 Series (1999+) Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-FC1-INST Rev C (FLEXI-COIL 67 Series (1999+)) NOTICE: NORAC
More informationRogator 64 and 74 Series and Willmar Eagle 8650 (JIC) & 84, 94 & 1386 Series (Flat Faced O-Ring) Installation Manual RG2 & RG6
RG2 & RG6 Rogator 64 and 74 Series and Willmar Eagle 8650 (JIC) & 84, 94 & 1386 Series (Flat Faced O-Ring) Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder
More informationTOYOTA TACOMA Part Number: TTA-BGB16-DRL TTA-BGP16-DRL
TOYOTA TACOMA 2016-17 Date: 10.29.2016 Billet Grille w/led DRL Part Number: TTA-BGB16-DRL TTA-BGP16-DRL Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 User Card
More informationROUSH Active Exhaust. Installation Instructions P/N: (R AVC) Fastback GT V8 - Convertible GT V8
Installation Instructions P/N: 422100 (R1318-5231AVC) Fastback GT V8 - Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active Exhaust Installation Instructions P/N: 422100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS WJ2 FULL-WIDTH FRONT BUMPER APPLICATION: 2018 Jeep Wrangler JL PART NUMBER: 59-80105, 59-80115, 59-80125 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 FRONT BUMPER ASSEMBLY
More informationWheel Angle Sensor Kit Installation
Wheel Angle Sensor Kit Installation Item Component Part Number Qty 1. Bracket Kit, WAS 200-0572-01 1 2. WAS Assembly 200-0468-01 1 3. Instruction Guide 602-0456-01 1 602-0456-01-A Overview Always shut
More informationHP10220 KIT. See application guide for proper fitment.
HP10220 KIT Dodge Dakota* (2WD/4WD) * 2005 All Dodge Dakotas 2006 - All Dodge Dakotas except Night Runner and R/T sub models 2007 - All Dodge Dakotas except SXT and TRX4 sub models 2008 - All Dodge Dakotas
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPart Number: TCA-712SE
Date: 09.04.2013 TOYOTA CAMRY SE 2012-14 LED DRL Part Number: TCA-712SE Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion
More informationRECOMMENDED SEQUENCE OF APPLICATION
TOYOTA TACOMA 2010- PART NUMBER: 250-8403 REARSIGHT KIT CONTENTS ITEM QTY DESCRIPTION 1 1 INTERFACE ADAPTER HARNESS 2 1 REAR CAMERA ASSEMBLY 3 1 CAMERA INTERFACE HARNESS 4 1 SACK PARTS COLOR APPLICABILITY/TRIM
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationTOYOTA PRIUS V LED DRL Black-Out
TOYOTA PRIUS V 2012 - LED DRL Black-Out Part Number: 00016-47021 Accessory Code:LDBO10 Conflicts Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver Box
More informationMS Sprayers NT 1000/1250 Installation Manual MS1
MS1 MS Sprayers NT 1000/1250 Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-MS1-INST Rev B (MS Sprayer NT 1000/1250) NOTICE: NORAC Systems
More informationFRONT DRIVELINE MODIFICATION MAY BE NECESSARY!!!!
INSTALLATION INSTRUCTIONS FOR 2009 DODGE 2500/3500 4WD & 1500 Mega Cab 6 SUSPENSION SYSTEM PART NUMBER 7206 Requires the following parts (sold separately) for a complete installation: Front Coil Spring
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case IH Combines 7010 7120 8010 8120 AFX 8010 9120 PN: 602-0283-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual carefully
More informationSUMMERS Pull-Type with Proxy Switch Sense Installation Manual SM2
SM2 SUMMERS Pull-Type with Proxy Switch Sense Installation Manual Printed in Canada Copyright 2012 by NORAC Systems International Inc. Reorder P/N: UC4.5-BC-SM2-INST Rev B (SUMMERS Pull-Type with Proxy
More informationDEALER SETUP INSTRUCTION
DEALER SETUP INSTRUCTION P/N XXXXXXX APPLICATION 2018 GTS 150 BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation instructions
More informationROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8
Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128
More informationADVANCE ADAPTERS INC. P/N: TJ 231/241 CABLE SHIFTER
Paso Robles, CA 93447 PAGE 1 of 10 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 09-25-15 KIT CONSISTS OF: # Qty Part No. Description 1 1 300474 WASHER-RUBBER YOKE SEAL 32 SPLINE 2 1 300476
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationSAFETY. Read and understand all safety precautions and instructions before installing this product.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationPart Number: TAV-713 TOYOTA AVALON LED DRL
Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents
More informationLIFT-304 (3 ) and LIFT-104 (6 ) Drop Spindle Lift Kits Yamaha G22, Gas or Electric Installation Instructions
LIFT-304 (3 ) and LIFT-104 (6 ) Drop Spindle Lift Kits Yamaha G22, Gas or Electric Installation Instructions LIFT-304 LIFT-104 Contents of LIFT-304/104 Yamaha G22 Lift Kit: a (1 ea.) Passenger Side Spindle
More informationINSTALLATION INSTRUCTIONS WARN FRONT RECEIVER For: DODGE RAM, 2500 and 3500, + 03 Kit Number: 65370
INSTALLATION INSTRUCTIONS WARN FRONT RECEIVER For: DODGE RAM, 2500 and 3500, + 03 Kit Number: 65370 USE EXTREME CAUTION WHEN DRILLING ON ANY VEHICLE. MAKE SURE THAT ALL FUEL LINES, BRAKE LINES, ELECTRICAL
More informationFord F150/Raptor & F150 Lower Control Arm Installation Instructions
2009-2010 Ford F150/Raptor & 2015-2017 F150 Lower Control Arm Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency
More informationINSTALLATION INSTRUCTIONS Progress Technology Rear Anti-Sway Bar Honda Civic Part # No Revision (7/20/16)
INSTALLATION INSTRUCTIONS Progress Technology Rear Anti-Sway Bar Honda Civic 96-00 Part # 62.1042 No Revision (7/20/16) WHO SHOULD INSTALL THIS PRODUCT? Progress Technology products should only be installed
More informationADVANCE ADAPTERS INC. P/N:
Paso Robles, CA 93447 PAGE 1 of 6 KIT CONSISTS OF: Qty Part No. Description 1 303303 SHIFTER BODY BARREL RETAINER 11 303311 HEAT SHIELD-FIREPROOF SLEEVE 1/2" 2 303312 BUSHING- IGUS 3/8" 2 303313 HEIM JOINT-
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W
B&W Trailer Hitches 6 Hawaii Rd / PO Box 86 Humboldt, KS 66748 P:60.473664 F:60.869.903 Turnoverball Gooseneck Hitch Installation Instructions MODEL 08
More informationINSTALLATION INSTRUCTIONS
PART NO. 23100T PRODUCT DESCRIPTION: Front Winch Bumper, Center Section PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE PERSONAL
More informationSUT-450-I ASSEMBLY REQUIREMENTS
SUT-450-I Torque wrench, carpenters square, wire cutters, Phillips screwdriver, 7/16, 9/16, and 3/4 combination wrenches, ratchet, 9/16,3/4,13/16, and 7/8 sockets. ASSEMBLY REQUIREMENTS *Torque all T-bolt
More informationINSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT
INSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT P FRONT 1 with MFK 4 for 2008 2019 CHEVROLET PASSENGER VANS W/DUAL SIDE SWING OUT DOORS P FRONT 2 with MFK 8 for 2008 2019 CHEVROLET
More informationWing-Fold Planters All Makes & Models
Wing-Fold Planters All Makes & Models Row by Row Down Force Master Kit PN: 2006444-ENG REV. C Introduction Important Information This guide provides the basic information needed to install the Ag Leader
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS GASOLINE TRUCKS ONLY R7 STEP BOARD APPLICATION: 007-017 Chevy Silverado/GMC Sierra 1500/500/3500 Ext. / Double / Crew Cab PART NUMBER: 8-7100, 8-7105, 8-71030, 8-71035 ITEM QUANTITY
More informationInstallation Manual TWM Performance Short Shifter Subaru STi 2008+
- 1 - Installation Manual TWM Performance Short Shifter Subaru STi 2008+ Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift from
More informationTOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationFIT SERIES FIT-3 W/ LEG PRESS
FIT SERIES FIT-3 W/ LEG PRESS ASSEMBLY INSTRUCTIONS Part # 734820 Rev C. Revision:4/04/03 KEY 2 3 4 5 6 7 8 9 0 2 3 4 5 6 7 8 9 20 2 22 23 24 25 26 27 28 29 30 3 32 33 34 35 36 37 38 39 40 4 42 PART #
More informationTOYOTA TACOMA LED DRL Black-Out
TOYOTA TACOMA 2013 - LED DRL Black-Out Part Number: 00016-35021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 1 Driver Box 3 1 Harness bag
More information