AUXILIARY LIGHTING SPARES // 87-92

Transcription

1 AUXILIARY LIGHTING SPARES // SPARES roadvision.com.au // Page 87

2 Universal Mounting & Wiring Accessories RBC HEAVY DUTY BULL BAR CLAMP BRACKETS Roadvision s range of RBC heavy duty bull bar clamp brackets provide professional mounting solutions for installing bar and driving lamps on bull bars. With tube mount kits available for 49mm-81mm diameter tube, they provide a sturdy yet quick and easy mounting solution for our complete range of forward lighting products. RBC4954B 49-54mm (2 ) Tube Black 8x25mm RBC4954S 49-54mm (2 ) Tube Silver 8x25mm RBC heavy duty bull bar clamp brackets suitable for installation of light bars or aerials Fits from 49mm to 81mm tube diameters (1.93 to 3.19 ) 8mm x 25mm mounting hole slot Heavy duty powder coated die-cast aluminium construction Internal protective rubber gasket Stainless steel hardware Simple DIY design Available in black or silver Sold as a pair (2 clamps) RBC6065B 60-65mm (2 1/2 ) Tube Black 8x25mm RBC6065B 60-65mm (2 1/2 ) Tube Silver 8x25mm RBC6671B 66-71mm (2 3/4 ) Tube Black 8x25mm RBC6671S 66-71mm (2 3/4 ) Tube Silver 8x25mm RBC7681B 76-81mm (3 ) Tube Black 8x25mm RBC7681S 76-81mm (3 ) Tube Silver 8x25mm TUBE MOUNT KITS Roadvision s range of tube mount kits provide professional mounting solutions for installing bar and driving lamps on bull bars. With tube mount kits available for 1.5 to 3 diameter tube, they provide a sturdy yet quick and easy mounting solution for our complete range of forward lighting products. BBL-CLMP-M Tube Aluminium Alloy M6 Mounting Hole (Each) BBL-CLMP-M Tube Aluminium Alloy M8 Mounting Hole (Each) BBL-CLMP-3B Universal Bull Bar X Clamp Bracket 3 Tube Cast Iron 15mm Mounting Hole (Pair) Page 88 // roadvision.com.au

3 LICENCE MOUNT KITS SECURITY MOUNT KITS Roadvision s licence mount bracket provides a professional mounting solution for installing bar and driving lamps on vehicles without a nudge or bull bar. Simply mount behind your number plate and you have a quick and easy mounting solution for our complete range of forward lighting products. Protect your investment with Roadvision s security lock nut kits, suitable for our complete range of LED bar & driving lamps, they provide an anti-theft solution and added piece of mind. ADJUSTABLE MOUNT KITS Signature red neoprene shock and vibration absorbers for ultimate performance and stability. The adjustable side mounts feature 6/9 height settings using cleaver rubber cam isolators. Designed with 2/3 slots, each slot can be top, centre or bottom mounted allowing for precise positioning. RAM Position Adjustable End Bracket Kit Suits SR2 Series (Pair) RALPB Universal Licence Plate Mount Bracket Fits Standard & Slimline Plates RAM Position Adjustable End Bracket Kit Suits DC2/DXC2 Series (Pair) RBKLK Lock Nut Kit Suit Bar Lights (Main Bolt M8x1.5mm x 2 - Side Bolts M8 x 2 - Includes 2 x Tools) FLASHER MODULES RBDLK Lock Nut Kit Suit Driving Lights (Main Bolt M10x1.5mm x 2 - Side Bolts M8 x 8 - Includes 2 x Tools) Add additional functionality to our range of LED bar or work lamps with Roadvision s remote controlled LED flasher module. Featuring 10 flash patterns, 10-30V 25A input, our LED flasher modules deliver complete control and total BWRC-MV Wireless Remote Control Wiring Kit 10-30V 25A 433MHz 50m Range 9 Flash Pattern + SOS Mode IP67 WIRING KITS Roadvision s wiring kits are a complete DIY solution providing a professional installation for bar and driving lamps. Complete with harness, relays, switches, plugs and connectors, our wiring kits make installation quick and easy. Complete wiring harness kits for driving & bar lamps Suitable for 12V or 24V vehicles Plug & play H4 piggy back connector Waterproof Deutsch or ATP connectors Supplied with 12V & 24V relays 2000mm RELAY 1000mm 2000mm RELAY Completed with illuminated rocker switch Works on both positive & negatively switched head lamp systems Simple DIY fitment 1000mm 2000mm RELAY 1000mm RVBWK Universal Single Bar Lamp Wiring Harness, Deutsch Connector, Bar Lamp Rocker Switch, 30A Fuse Suits up to 140W Light Bars RVBHWK Universal Heavy Duty Single Bar Lamp Wiring Harness, ATP Connector, Bar Lamp Rocker Switch, 30A Fuse Suits 140W or Greater Light Bars RVDWK Universal Driving Light Wiring Harness, Deutsch Connectors, Driving Lamp Rocker Switch, 30A Fuse Suits Pair Driving Lights roadvision.com.au // Page 89

4 EASY TO FIT Mount receiver box in engine bay Plug driving lamps in using either the Deutsch plugs or push on terminals Connect B+ & B- wires to battery using 8mm ring terminals Cut high beam wire and feed 2 sides of the high beam wire and high beam feed from receiver into 3M connector Crimp using a standard pair of pliers Plug cigarette lighter transmitter into cigarette lighter plug PART NUMBER: RCWL Receiver Module 2m Sheathed Harness Deutsch DT 2 Pin Connectors 1m Sheathed Harness 3M Scotchlock IDC Tap Connector UG 2m High Beam Wire 8mm Ring Terminal In-Line Fuse 20A Blade 8mm Ring Terminal To Driving Lamps Female Push on Terminals 100mm Harness B+ To Vehicle High Beam Vehicle Battery B- Transmitter Module FITTING INSTRUCTIONS 1. Remove the main ground from the negative (B-) battery terminal. WARNING: This may result in a loss of radio security code and clock settings. Consult your owner s manual before disconnecting. 2. Install driving lamps to vehicle on a suitable mounting surface away from exhaust system or turbo. 3. Find a suitable place within the engine bay and mount the receiver box ensuring that the cables are long enough to reach the battery, driving lamps and high beam wire. 4. Identify the driving lamp connection leads from the receiver module; these are fitted with 2 pin Deutsch connectors. 5. Plug the driving lamp leads into your Roadvision driving lamps using either the 2 pin waterproof Deutsch connectors or female push on terminals. Take care to ensure the black lead is connected to battery negative input (B-) and red lead is connected to battery positive input (B+) to your driving lamps. 6. Identify the blue high beam feed wire from the receiver module. 7. Using a multimeter or test light find the active high beam switching wire located at the back of the head lamp. 8. Cut wire in a suitable position and feed both ends along with the blue high beam feed wires into the supplied 3M Gel filled connector. Crimp connector with a suitable pair of pliers. 9. Identify the main battery connection leads from the receiver module; these are fitted with 8mm ring terminals. Page 90 // roadvision.com.au 10. Connect the 8mm battery positive (Red B+) and battery negative (Black B-) leads to the vehicles main battery terminals using the 8mm ring terminals. 11. Re-connect the main battery negative (B-) terminal 12. Secure all excess wire to the vehicle. 13. Plug in the cigarette lighter transmitter module into your cigarette lighter plug inside the vehicle. 14. Test the driving lamps by turning on the ignition, transmitter switch to ON and head lamp switch to high beam. If the lights do not operate correctly, check the following: Check switch operation Green LED illuminated with lamps OFF and ignition ON, red & green LED s illuminated with switch ON and ignition ON. Check that you have followed all installation steps Inspect the fuse holder for blown fuse Inspect battery terminal connections Check 3M Gel filled connector connection Note 1: This wiring harness is designed for use with 2 lamps only not exceeding 10 amps per light or a maximum output of 20 amps. Note 2: By law in Australia, driving lamps must be operated through both the vehicles high beam circuit and an additional ON/OFF switch. For applications outside Australia or where driving lamps are not being connected, simply connect the blue high beam feed wire to battery positive (B+).

5 Universal Remote Wiring Accessories REMOTE WIRING KITS AIRWIRE takes all the effort out of installing driving lamps A simple kit that can be easily fitted by workshops or the DIY handyman. No need to drill holes in the firewall or mount switches in the dash Simply mount the receiver box and connect directly to the battery, splice in the high beam feed, plug in the driving lamps and cigarette lighter transmitter and you are done It s that easy. WIRELESS TECHNOLOGY FITTING DRIVING LAMPS HAS NEVER BEEN SO EASY! Easy to install complete DIY kit - 30 min Suitable for the average home handyman Requires RCWL - AIRWIRE only basic tools for installation Remote No Control drilling Wiring holes Loom through Kit the firewall and dash Fits UNIVERSAL Kit can be DRIVING easily moved LAMPS from vehicle to vehicle Multi-Volt 9-32V DC Input Fully potted electronics & waterproof 5m transmitter range & 3m plug & play harness 20A maximum output Deutsch & 3M gel filled connectors Lamps OFF Transmitter Illuminated Green only Lamps ON Transmitter Illuminated Red & Green roadvision.com.au // Page 91

6 Spares & Accessories WIRING ACCESSORIES & CHARGERS B AMP Plug 3 Pin 200mm Fits LUMENX SERIES TLCM60 Trailer Lamp Timer Module 60 Minute B817-49L AMP Plug 3 Pin 2.5m Fits LUMENX SERIES TLCM180 Trailer Lamp Timer Module 180 Minute B AMP Plug 3 Pin to PL3 Adaptor TLCM30 Trailer Lamp Timer Module 30 Minute BRACKETS & MOUNTING ACCESSORIES RVMBU U Mounting Bracket Stainless Steel Fits UNIVERSAL SUIT WORK LAMPS Magnetic Base Mounting Kit Fits UNIVERSAL Mounting Bracket Triple Fits 1217/817 SERIES TLCM1 Trailer Lamp Timer Module Wiring Harness BBL-BKT01 Replacement Sliding Bracket Universal (Pair) BBL-BKT02 Replacement End Bracket Rollar Series (Pair) BBL-BKT05 Replacement End Bracket DC/DCS/DCSX/DCX Series (Pair) B Grommet Rubber Fits 1217 SERIES BBL-BKT04 Replacement Sliding Bracket SR Series (Pair) COVERS BPLC153 6 Clip on Clear Protective Cover to suit DC/DCS Series 85 x 153mm BPLC Clip on Clear Protective Cover to suit SR Series 57 x 240mm BPLC203 8 Clip on Clear Protective Cover to suit DC/DCS Series 85 x 203mm BPLC-1080 Clip on Clear Protective Cover to suit BDL1080 Series Page 92 // roadvision.com.au