Measurements Lab (620451):

Size: px

Start display at page:

Download "Measurements Lab (620451):"

Charla Horn
5 years ago
Views:

1 Measurements Lab (620451): To introduce the practical side of actuators and sensors, also helping to understand how that device can be used. 1. INTRODUCTION FOR MEASURMENT 2. NOISE MEASUREMENT 3. PIEZO-ELECTRIC ACCELEROMETER MEASUREMENT OF ACCELERATION 4. PRESSURE TRANSDUCERS 4.1 CAPACITANCE PROBE PRESSURE TRANSDUCER 4.2 BIMETALLIC PRESSURE TRANSDUCER 4.3 LINEAR POTENTIOMETER PRESSURE TRANSDUCER 4.4 LVDT PRESSURE TRANSDUCER 4.5 STRAIN GAUGE PRESSURE TRANSDUCER 5. CALIBRATION OF A PRESSURE GAUGE 6. LIQUID LEVEL MEASUREMENT 6.1 CAPACITANCE PROBE 6.2 CONDUCTANCE PROBE 7. THE WHEATSTONE BRIDGE 8. OPERATIONAL AMPLIFIER 8.1 DIFFERENTIAL MODE AMPLIFIER 8.2 COMMON MODE AMPLIFIER 8.3 USING OPERATIONAL AMPLIFIER WITH WHEATSTONE BRIDGE 9. STRAIN GAUGES 9.1 BASIC STRAIN GAUGE 9.2 DUAL GAUGE SYSTEM 10. CALIBRATION AND TESTING OF THERMOCOUPLES 10.1 THERMOCOUPLE EMF 10.2 CONTROLLED COLD JUNCTION THERMOCOUPLE

2 Internal Combustion Engines Lab (620546) To introduce the practical side of Internal Combustion Engines. 1. INTRODUCTION 1.1 SPARK IGNITION ENGINES (OTTO CYCLE) 1.2 COMPRESSION IGNITION ENGINES (DIESEL CYCLE) 1.3 KNOCKING (DETONATION) 1.4 BASIC TERMINOLOGY 2. MORSE TEST 3. WILLAN S LINE TEST 4. FULL LOAD PERFORMANCE 5. HEAT BALANCE 6. SPARK IGNITION ENGINE IGNITION LOOP 7. SPARK IGNITION ENGINE MIXTURE LOOP 8. CO ANALYSIS 9. HALF LOAD PERFORMANCE ENGINE BREATHING 10. FLASH AND FIRE POINTS

3 Mechanical Eng Lab (640346): To introduce the practical side of Fluid Mechanics, Heat Transfer and Strength of Materials. Fluid Meters in Incompressible Flow. Impact of a Jet of Water. Heat Exchangers. Thermal Conductivity. Thermal Radiation & Natural Convection. Fatigue Test. Application of Mechanical Load Cell (Bending). Torsion Test. Tensile Test.

4 Mechanical Vibration Lab(620476) : To introduce the equation of motion for some vibrating system. 1-Mass Spring System 2-Simple Pendulum 3-Compound pendulum 4-Bifilar suspension 5-Torsion oscillation of single rotor 6-Lateral vibrating of Abeam with one or more Bodies Attached 7-Forced Vibration with negligible Damping 8-Un damped Vibration 9-Damped transverse Vibrating 10-Pizo Electrometer measurement of acceleration 11-Acceleration Experiment 12-Static and Dynamic Balancing 13-Whirling of Rotating Shafts 14-Frequency Response of Vibrating System 15-Torsion Oscillation of Two Rotors Gyroscope

5 Strength and Properties of Material Lab(620366): To introduce the principles of strength and properties of material as a vehicle for engineer applications. Tensile Test. Compression Test Shear Test. Torsion Test Impact Test Fatigue Test. StrainGauge Measurement. Creep Test. Hardness Test. Application of Mechanical Load Cell. Corrosion Experiment. Examination of Material Microstructure.

6 Automatic Control Lab (620457): To introduce the practical side of automatic control, including ON-OFF control, open loop control, closed loop control. 1. INTRODUCTION TO AUTOMATIC CONTROL 2. ADJUSTABLE BI-METALLIC STRIP THERMOSTAT 3. CAPILLARY BULB THERMOSTATIC CONTROLLER 4. ERROR OUTPUT IN THE POSITION CONTROL 5. CLOSED LOOP POSITION CONTROL 6. CLOSED LOOP SPEED CONTROL 7. OPERATIONAL AMPLIFIER AS AN ERROR DETECTOR 8. GAIN OF THE SYSTEM VS. SPEED CONTROL

7 HEAT TRANSFER Lab (620446) To introduce the practical side of heat transfer, also to get a better understanding for the basic modes of heat transfer (Conduction, Convection and Radiation). 1. INTRODUCTION 2. MARCET BOILER EXPERIMENT. 3. THERMAL CONDUCTIVITY 4. NATURAL CONVECTION AND THERMAL RADIATION 5. FORCED CONVECTION 6. HEAT EXCHANGER (Parallel and Counter) 7. HEAT EXCHANGER (Flow Rate Variation) 8. FILMWISE AND DROPWISE CONDENSATION 9. AIR CONDITIONING (HEAT PUMP) 10. AIR CONDITIONING (AIR COOLER)

8 Fluid Mechanics Lab(620336): To introduce the practical side of fluid mechanics. Introduction (Density, Surface Tension and Viscosity). Flow Measurements. Impact of Jet. Open Channel Flow (Sluice gate, Weirs, Hydraulic Jump and Manning Formula). Losses in pipes. Pressure Distribution about a Circular Cylinder. Drag Force Determination. Analysis of an Airfoil. Turbine and Pump Unit.

9 Mechanical Drawing (620221): The main purpose of this course is to give the basics of Drawing Techniques through Mechanical Parts. 1- (2-D) drawing (Manual+ Mechanical Desktop) 2- (3-D)drawing(isometric and oblique for Manual+ Mechanical Desktop) 3- Screws (Manual+Mechanical Desktop) 4- Views(Manual+Mechanical Desktop) 5- Tolerance(Manual+Mechanical Desktop) 6- Options in Mechanical Desktop

10 Engineering Workshop(620161): To teach the students to respect the technical work and discipline, also to gain hand and technical skills. Engineering materials principle Basic measuring instruments (Vernier caliper, micrometer, dial gauge, etc.) Various manufacturing processes: Forming processes (Forging, Bending and Shearing). Metal cutting (Turning, Milling, Drilling, Reaming and Grinding). Metal joining (Soldering, Welding: Electric, Arc welding, Gas welding and Spot welding. Mechanical fasteners: Screws, Bolts, Nuts and Rivets). Sand Casting Safety regulations in workshop.

Faculty of Mechanical Engineering B.E. Mechanical Engineering (Sandwich) (R 2013) Semester III. Requirements for a batch of 30 students

Sl. No. Faculty of Mechanical Engineering (R 203) Semester III CE635 STRENGTH OF MATERIALS LABORATORY (R) (A) Deficiency (R - A). Universal Tensile Testing machine with double shear attachment 40 Ton Capacity