Assembling a Wall-Mounted CTS
|
|
- Eugene Spencer
- 5 years ago
- Views:
Transcription
1 CHAPTER 3 Revised: February 4, 2010, This chapter provides you with the information you need to assemble a wall-mounted CTS and includes the following sections:, page 3-1 Installing the External Presentation Cable Holder, page 3-22 Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Warning Installation of the equipment must comply with local and national electrical codes. Note The directions left and right refer to the assembly when you face the display. To assemble a wall-mounted CTS , complete the following procedure. See Table 3-1 for the list of parts that are required for this assembly procedure. The parts are keyed to numbers; use these numbers to refer to the parts in the illustrations. Table 3-1 Parts List for Wall-Mounted CTS Key Part Description Part Number Qty Notes CTS Wall Stand, Display Screen and Cabling 1 Wall Stand Assembly Kit CTS500-STRUC-WALL 1 Carton 2 2 Display Screen Assembly including speaker assembly, camera assembly and light fixture CTS-500-DISP37-INT 1 Carton 3 3 Cable bundle From CTS500-ACC-KIT 1 Carton 1 4 Light Reflector Panel CTS500-LIGHT-REFL 1 Carton 5 5 Light Fixture CTS500-LIGHT-FIXT 1 Part of display assembly 3-1
2 Table 3-1 Parts List for Wall-Mounted CTS (continued) CTS Codec, Codec Base and Codec Cover 1 CTS codec Carton 4 2 Handle/Mounting bracket Carton 4 3 Rear cover Carton 4a or 4b 4 Mounting base Carton 4a or 4b 5 Left end cap Carton 4a or 4b 6 Top Cover Carton 4a or 4b 7 Right end cap Carton 4a or 4b 8 M4 x 6mm flat head screws Carton 4a or 4b 9 M5 x 12mm hex head screws Carton 4a or 4b 10 M4 x 10mm pan head screws Carton 4a or 4b 11 Display Screen Assembly including speaker assembly, camera assembly and light fixture CTS-500-DISP37-INT 1 Carton 3 12 Cable bundle From CTS500-ACC-KIT 1 Carton 1 13 DVI-to-VGA cable Carton M Ethernet cable, black For Cisco Unified IP Phone or network connection 15 8M Ethernet cable For Cisco Unified IP Phone or network connection Wall-Mounted Cable Cover 1 Screw anchor Kit # #8 x 1 1/2-inch screw Kit # Cable cover base Kit # Cable cover facade Kit # Procedure Step 1 Determine the correct height to install the wall plate (wall mount bracket). Use one of the following calculations: If the CTS will be primarily used by a single user, and that user is available, measure the user s eye level while they are seated. Then refer to Figure 3-1 to calculate the correct wall mount height. Tip The display is at the correct height when the user s eye level is at approximately 70 percent of the total height of the display screen. 3-2
3 If the user is not available, or if the CTS will be used by multiple persons, refer to Figure 3-2 for the generic wall mount height. Figure 3-1 Wall-Mount Vertical Height Guidelines With the User s Seated Eye Height Wall Plate (For Wall Mount Bracket) 8 in (20 cm) 4.75 in (121 mm) Eye height measurement minus 8 in (20 cm) Measured eye height (sitting)
4 Figure 3-2 Generic Wall-Mount Vertical Height Guidelines Wall Plate (For Wall Mount Bracket) 4.75 in (121 mm) 40 in (101 cm) 48 in (122 cm)
5 Step 2 Step 3 Step 4 Step 5 Attach the wall mount to the wall using the instructions that are provided with the wall mount kit. Locate carton 3 (CTS-500-DISP37-INT). This carton contains the display. Remove the cardboard from the top and sides of the carton 3 packaging, but do not remove the display from the carton. Remove the buttons from the rear of the display. Note Step 6 Step 7 Step 8 Save the screws; you use the screws when you attach the interface bracket to the display. Attach the interface bracket to the display using the screws that you removed in Step 5 and the spacers that are provided in the wall mount kit. Detailed instructions are provided in the wall mount kit. Attach the mounting cup to the interface bracket using the screws that are provided in the wall mount kit. Detailed instructions are provided in the wall mount kit. Remove the display top rear cover from the display. Figure 3-3 Removing Display Top Rear Cover
6 Step 9 Connect the cables to the following connections on the top of the display: Connect the speaker connections to the spade terminal connections. The cables are labeled red for the right speaker and white for the left. Note Because you are viewing the display from the rear, left and right are reversed. Connect the Ethernet cable to the Ethernet connection for the camera. Connect the DVI cable to the DVI camera connection. Figure 3-4 Cable Connections for the Display, Top Right speaker (Red) Left speaker (White) Camera Ethernet Camera DVI
7 Step 10 Replace the display top rear cover. Tip To make cover replacement easier, tie the wires together with a zip tie and make sure that the ferrite cores on the wires are outside of the cover. Figure 3-5 Replacing the Display Top Rear Cover
8 Step 11 Connect the cables to the following connections on the underside of the display: If it is not already connected, connect the HD video cable to the HD video connection for the display. Connect the power cord to the power inlet. Use the power cord that does not have a 90 degree right angle at the power inlet; the part number is Note Keep the power and signal cables separate; do not connect the power and signal cables together. Connect the microphone. The microphone connection is on the lower rear of the display. (Optional) Connect the Auxiliary HD Video connection to the Digital Media Player (DMP). Figure 3-6 Cable Connections for the Display, Underside and Lower Rear Microphone (Lower rear) On/Off switch Digital Media Player (DMP) (Optional) AC inlet HD Video primary input Microphone 3-8
9 Step 12 Step 13 Remove the CTS codec from its packaging. Remove the mounting bracket that is closest to the power inlet and power switch from the codec by unfastening the four screws. Note This bracket is referred to as the left bracket in the following steps; this side of the codec is the left side during assembly of your CTS Figure 3-7 Removing the Handle/Mounting Bracket (Power Inlet/Left side)
10 Step 14 Insert the tab of the rear cover in the slot between the right handle/mounting bracket and the codec. Figure 3-8 Rear Cover and Right Handle/Mounting Bracket
11 Step 15 Insert the lower part of the right handle/mounting bracket into the mounting base, making sure that the notched part of the base hooks under the handle. Tip To facilitate installation of the codec to the mounting base, place the codec on its side on a table so that the lower part of the codec hangs over the edge of the table. Do not scratch the table or the codec during installation. Figure 3-9 Right Handle/Mounting Bracket and Mounting Base
12 Step 16 Reattach the left handle/mounting bracket to the codec assembly by refastening the four screws. Figure 3-10 Left Handle/Mounting Bracket and Codec Assembly
13 Step 17 Step 18 Connect the cable bundle to the codec as follows: Connect the Ethernet cable from the display to the white camera Ethernet connection. Connect the microphone cable to the microphone connection. Connect the left speaker to the white speaker connection. This connection is also indicated by two dots. Connect the right speaker cable to the red speaker connection. This connection is also indicated by three dots. Connect the HD video cable to the HD video display connection. Attach the remaining cables to the codec as follows: Connect the power cord to the power inlet. Use the power cord that has a 90 degree right angle at the power inlet; the part number is Caution Do not yet connect the cord to an active power source. Connect an Ethernet cable to the Cisco Unified IP Phone Ethernet connection indicated by a white phone icon on the CTS codec. Connect the other side of this connection to the Cisco Unified IP Phone Connect a network cable to the network connection on the codec. Connect the other side of this connection to an external network connection. (Optional) Connect the DVI connector from the DVI-to-VGA cable bundle to the Presentation Source In connection. (Optional) Connect the DMP Audio or Presentation Audio connection to one of the following input sources: The audio connection from the DVI-to-VGA cable bundle The audio connection from the DMP Note You can configure the DMP audio to play when you are not in a TelePresence call. For more information, see the Testing the LEDs and Light Fixture and Configuring the Digital Media Player Audio section on page
14 Figure 3-11 shows the required connections for the CTS codec. Figure 3-11 Cable Connections for the Codec External Presentation Display (optional) Display Presentation Source In IP Phone Camera Network DMP Audio or Presentation Audio (optional) Headset or Bluetooth-enabled Base Station (optional) Microphone Document Camera (optional) Right Speaker Left Speaker 3-14
15 Step 19 Place the left end cap on the CTS codec assembly. Note The left end cap has an access slot for the power-on switch. The right end cap does not have this slot. Figure 3-12 Left End Cap 9 5 View A View A
16 Step 20 Attach the top cover to the CTS codec assembly with two screws and route the cables through the hole in the rear center of the cover. Note The hole for the cables is not visible in Figure 3-13; it faces the rear of the codec. Tip If your installation does not have enough space behind the codec to route the cables through the hole in the top cover, route the cables through either the left or right end cap. Note Tighten the screws until they are snug but do not overtighten. Figure 3-13 Top Cover
17 Step 21 Attach the end caps to the CTS codec assembly and fasten them with the screws. Note Tighten the screws until they are snug but do not overtighten. Figure 3-14 Right End Cap
18 Step 22 Remove the light reflector panel from carton 5 and slide the light reflector panel into the display screen assembly. Figure 3-16 provides additional detail of the mounting slots and display screen bracket. Note If you encounter problems when you mount the panel, remove the light fixture by disconnecting the wiring connector on the left side of the assembly and lifting the fixture straight up. See Figure 3-17 for an example of light fixture removal. Replace the light fixture after you mount the light reflector panel. Figure 3-15 Mounting the Light Reflector Panel to the Display Screen Assembly
19 Figure 3-16 Mounting the Light Reflector Panel to the Display Screen Assembly Detail
20 Figure 3-17 Removing the Light Fixture from the Display Screen Assembly to Ease Reflector Attachment
21 Step 23 Using the cable cover base as a guide, mark holes on the wall for the cover mounting points. See Figure 3-18 for the location of the mounting points. Note Step 24 Step 25 Step 26 The cable cover hides the cables between the display and the codec. Mount the cover on the wall so that it is approximately midway between the codec and display. Be sure to center the cover vertically between the codec and display. Using a drill and 1/8-inch drill bit, drill pilot holes for the anchors. Insert the anchors into the pilot holes and screw them in. Place the cable cover base on the wall and secure it to the anchors using the screws. Figure 3-18 Attaching the Cable Cover Base to the Wall
22 Installing the External Presentation Cable Holder Step 27 Route the cables into the trough in the cable cover base, then snap the cable cover facade into place. Figure 3-19 Attaching the Cable Cover Facade to the Base Step 28 Step 29 Peel off the protective plastic film from the front of the display. (Optional) attach the cable management holder to its attachment point by completing the steps in the Installing the External Presentation Cable Holder section on page Installing the External Presentation Cable Holder The CTS includes a DVI-to-VGA cable that allows you to connect your system to an external presentation source. A cable holder is included with the CTS system to assist in the management and routing of this cable. You route the cable from the codec to the location of the presentation source (for example, a laptop computer) and install the cable holder at that location. See Table 3-2 for the list of parts that are required for this assembly procedure. The parts are keyed to numbers; use these numbers to refer to the parts in the illustrations. 3-22
23 Installing the External Presentation Cable Holder Table 3-2 Parts List for Cable Holder CTS Cable Holder 1 Cable Holder Front Cover Carton 9 2 Cable Holder Rear Cover Carton 9 3 M4 pan head screw Carton 9 To install the cable holder, complete the following steps: Step 1 Step 2 Step 3 Open carton 9, part number CTS-CABL-HLDR-SYST, and remove the components from their packaging. Determine a suitable location for the cable holder (for example, on the edge of a desk near a laptop computer). Route the cable through the front cover. Step 4 Attach the rear cover to the location you determined in Step 2. Step 5 Step 6 Attach the rear cover to the cable holder assembly. (Optional) Use the Velcro to join the audio jack and the VGA cable together. Figure 3-20 Assembling and Attaching the Cable Holder 2 1 Table top
24 Installing the External Presentation Cable Holder 3-24
Assembling the Front Panel
CHAPTER 4 Revised: September 22, 2009, This chapter describes how to assemble the front panel that covers the lower half of the Cisco TelePresence System 1000 and includes the following sections: Parts
More informationCisco TelePresence IX5000 and IX5200 Installation Guide
Cisco IX5000 and IX5200 Installation Guide Cisco TelePresence IX5000 and IX5200 Installation Guide Revised: November 6, 2017 - Summary of Changes: November 6, 2017: Removed the wiring diagram and put in
More informationInstalling the Front Row Tabletops
Installing the Front Row Tabletops 4 Install 2x half moon bolt assemblies (51-6068-xx) into slots in the bottom of tabletop assemblies A&B. Use 10mm open end or ratcheting wrench to tighten the nuts and
More informationTOYOTA im NAVIGATION UPGRADE Preparation
Preparation Part Number: PT296-00170 PT296-12170 (Extension Module w/ AHA) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna kit 5 6 Bolt
More informationSCION im PREMIUM AUDIO Preparation
SCION im 2016 - PREMIUM AU Preparation Part Number: PT296-12160 (Extension Module w/ AHA) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna
More informationSCION tc PREMIUM AUDIO Preparation. Part Number: PT (Extension Module w/ AHA)
Preparation Part Number: PT296-12160 Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module 2 1 BT cable 3 1 DA/Ext Harness 4 1 GPS Antenna kit 5 6 Bolt (M5x8) 6 5 Wire tie (10 ) Hardware
More informationPVM 220 Installation Guide
R CONFIG SELECT AUDIO 1 3 5 2 4 AUX INPUT VOICELIFT PAGING SENSOR SENSITIVITY PVM 220 Installation Guide The Extron PVM 220 is an enclosure for the safe mounting of PoleVault system devices in the plenum
More informationDukane Projection System (DPS)
Dukane Projection System (DPS) Installation Guidelines CEILING SCREEN CAMERA SPEAKERS VCR/DVD PC 1. Determine or measure the screen width or diagonal which corresponds to your projector to find the maximum
More informationAUDIO KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
AUDIO KIT P/N 2882696 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationPVM 220 Installation Guide
R CONFIG SELECT AUDIO AUX INPUT VOICELIFT PAGING SENSOR SENSITIVITY PVM 0 Installation Guide The Extron PVM 0 is an enclosure for the safe mounting of PoleVault system devices in the plenum area of a suspended
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More informationINSTALLATION INSTRUCTIONS FORD SUPER DUTY NOTE: (Vehicle Retains Tow Hook) PART # P3064
INSTALLATION INSTRUCTIONS 2011-14 FORD SUPER DUTY 250-550 NOTE: (Vehicle Retains Tow Hook) PART # P3064 PARTS LIST: Qty Description Qty Description 1 Grill Guard 2 10mm x mm Hex Bolts 1 Driver/Left Lower
More informationCHAPTER S e t u p NOTICE:
CHAPTER Setup NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering
More informationSCION iq AUDIO Preparation
Preparation Part Number: PT546-00140 (Base Radio) Kit Contents Item # Quantity Reqd. Description 1 1 Receiver Assembly, Radio Unit 2 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationSCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT
Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface
More informationAdjustable Light Kits E-Z-Go TXT All Models Installation Instructions
Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationParts List Continues on Next Page
Assembly Instructions and Owner s Manual Description: Quantum Hardcoated Polycarbonate UTV Windshield, Wash n Wipe Full Size Model: Part Number: N30202 Installation Time: 60 min Polaris RZR 800, Round
More informationYARIS 4-DOOR 2007 INTERIOR LIGHT UPGRADE
Document # 3999 4/26/06 4-DOOR 2007 INTERIOR LIGHT UPGRADE Preparation Part Number: 00016-52060 Code: IL1 Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide 3 1 Hardware
More informationSCION xd INTERIOR LIGHTING UPGRADE Preparation
Preparation Part Number: PTS21-52085 Light Guide Kit Contents Item # Quantity Reqd. Description 1 1 Controller Board, 4 color programmed w/ Bracket 2 1 RGB, LED Engine wire harness 3 2 14mm Light Rod,
More informationIf technical support is required, please contact Advent Technical Support at
Document 128-9015A Created 12/12/11 Kit Contents: Item # Qty. Component Description 1 2 Headrest Assembly 2 2 Cables # 3 3 1 Power Cord # 9 4 1 FM Antenna 5 1 Control Box 6 2 IR Headphones 7 2 Remote Control
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More information(1) Remote Control with (2) AAA Batteries
TOOLS REQUIRED: KIT CONTENTS: E14 Torx (1) Remote Control with (2) AAA Batteries (2) Wireless Headphones with (4) AAA Batteries (2) DVD Headrest Units Owner s Manual (1) Owner s Manual (1) Power / Audio
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. DESCRIPTION: APPLICATION: PART NUMBER: Accent light Kit Cube (MY2013+) 999F3 AW000 - Universal Accent Lighting Kit. 4. KIT CONTENTS: Item QTY Description
More informationDocument # 2506 Created 6/23/04 SCION tc INTERIOR LIGHT UPGRADE Preparation Part Number: (Amber) (Blue) Code: YI-1,YI-2
Document # 2506 Created 6/23/04 SCION tc 2005 - INTERIOR LIGHT UPGRADE Preparation Part Number: 00016-21010 (Amber) 00016-21020 (Blue) Code: YI-1,YI-2 General Applicability Kit Contents All Item # Quantity
More informationINSTALLATION INSTRUCTIONS Dodge Ram Crew / Mega 2500/3500 2/4WD NOTE: (tow hooks will not be re-attached) PART # P5056
INSTALLATION INSTRUCTIONS 2010-14 Dodge Ram Crew / Mega 2500/3500 2/4WD NOTE: (tow hooks will not be re-attached) PART # P5056 PARTS LIST: Qty Description Qty Description 1 Grill Guard Bar 6 12mm x 30mm
More informationSwitch Installation. Preparing for Installation. Warnings CHAPTER
CHAPTER This chapter describes how to start your switch and how to interpret the power-on self-test (POST) that ensures proper operation. It also describes how to install the switch. Read the topics and
More informationJEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market
1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter
More informationTOYOTA VENZA HANDS FREE BLU LOGIC Preparation
TOYOTA VENZA 2009- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationDODGE / RAM 1500 *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMENDED TOWING CAPACITY ***
6444 DODGE / RAM 500 6/8/207 OF 5 *** DO NOT EXCEED MANUFACTURER'S RECOMENDED TOWING CAPACITY *** ITEM QTY PART NUMBER 0 /2-3 x 2" 2 4 /2-3 x 3/4, GR8 3 4 CM-SP2 4 2 CM-SP6 5 4 HFN 23, GR8 6 2 CM-SP4 7
More informationTOYOTA TACOMA XM SATELLITE RADIO Preparation
Preparation Part Number: Mounting Kit PT546-35090 Tuner Assembly 8680-0W03 NOTE: Part number of this accessory may not be the same as the part number shown. Tuner Assembly Kit Contents (8680-0W03) Item
More informationBrake and Tail Light Kit Workman 1100/2100 and Twister Utility Vehicles
Form No. 5-90 Brake and Tail Light Kit Workman 00/00 and Twister Utility Vehicles Part No. 0 6697 Installation Instructions Important Before installing this kit, you must have Wiring kit number 99 79 installed
More informationLEXUS CT 200h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left
More informationRevised 10/22/2014 Page 2 of?
1.Remove side panels, hood, seat, fuel tank, and 2.Remove stock air box, remove fuel line muffler. Save exhaust springs and rubber muffler mounts for turbo bracket. Sand back surface flat for mounting.
More informationSCION XB HANDS FREE BLU LOGIC Preparation
SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationU L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M
S m a r t e r Q u i e t e r M o r e A c c u r a t e U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M Installation Manual PASSPORT 9500ci Comes Complete Front Radar Receiver Miniature weatherproof
More informationSCION FR-S FOG LIGHTS
Part #: PT413-18130 Conflicts: Lowering Springs PTR07-18130-LL (California only) Kit Contents: For Anniversary Edition, Monogram & RS 2.0 vehicles, additional parts need to be ordered (PT413-18130-LL)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Document# 19-0038 2004+ Lotus Elise (Series 2) Rear Clamshell Removal Kit Safely support the vehicle. This is a two-person job. Allow 1 to 2 hours for initial disassembly. Have
More informationTOYOTA tc HANDS FREE BLU LOGIC Preparation
TOYOTA tc 2011- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationTOYOTA CAMRY HANDS FREE BLU LOGIC Preparation
TOYOTA CAMRY 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationPLAYDIUM Payment Door FRU Installation Guide
March 2015 900908-001 Rev 01 Purpose PLAYDIUM Payment Door FRU Installation Guide This document provides information about the Playdium Payment Door Field-Replaceable Unit (TouchTunes p/n: 600221-001)
More informationINSTALLATION INSTRUCTIONS DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD)
INSTALLATION INSTRUCTIONS 1997-1999 DODGE DAKOTA 2 KIT # 682 (2WD), 692 (4WD) 3 KIT # 683 (2WD), 693 (4WD) Installation of a Performance Accessories body lift kit will change the vehicle s center of gravity
More informationDVL Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Assemble the Face... 6 Attach the Surround Panels (if applicable) and Face... 10 Hang
More informationInstallation Instructions
Roller & Roman Shades Lifting Systems Cassette and Sure-Lift EZ Lift Cordless EZ Pull Standard and Cassette R-Series Clutch SL-Series Clutch Spring Roller Fascias and Valances 3, 4 Flat and 4 Curved Fascia
More informationPVM 220 Installation Guide
R CONFIG SCT DIO X INPUT NORMA VOICIFT NORMA PAGING OR ITIVITY PVM 0 Installation Guide The xtron PVM 0 is an enclosure for the safe mounting of PoleVault system devices in the plenum area of a suspended
More informationAF7006 Alarming Camera Display Unit (6.5 ) AF7015 Alarming Camera Display Unit (4.5") AF7216 Camera Sensor
How to Setup a Display Unit AF700 or AF70 AF7 AF700 Alarming Camera Display Unit (. ) AF70 Alarming Camera Display Unit (.") AF7 Camera Sensor Battery-powered alarming system with AC power connections
More informationSCION tc Navigation System Preparation. Part Number: PT
Preparation Part Number: PT611-21111 Kit Contents Item # Quantity Reqd. Description 1 1 Navigation System 2 1 GPS Antenna 3 1 Bluetooth Antenna 4 1 Wire Harness (Reverse / Park Brake) 5 1 RCA Relay Cable
More informationInstallation Instructions Pro-3600
Installation Instructions Pro-3600 Laser/Radar Detector THE WHISTLER GROUP, INC. CORPORATE HEADQUARTERS 3604 NW Frontage Rd. Bentonville, AR 72712 TEL 479.273.6012 FX 479.273.2927 P/N 202903 The Whistler
More informationInstallation 3000/6000 Profile
Installation 1 Unpacking Bolts: 2x Type A 2x Type B Monitor Top Module Column and Foot 4x Type C Cable Cover, Back Cover and Base (Wheel base option) Wrench Screw driver (for removing the handles on 6000
More informationConflicts: JBL Audio, Factory Navigation, Accessory XM Satellite Radio, and Accessory Sirius Satellite Radio
TOYOTA YARIS SEDAN 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts: JBL Audio, Factory Navigation,
More informationINSTALLATION INSTRUCTIONS BULL BAR DODGE RAM 1500 PART # B-D1091;B-D2091
INSTALLATION INSTRUCTIONS PART # B-D1091;B-D2091 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Brackets (for trucks without tow hooks only) 8 12-1.75mm Hex Nuts
More informationINSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063
INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1
More informationTOYOTA TUNDRA HANDS FREE BLU LOGIC Preparation
TOYOTA TUNDRA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00111 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationTOYOTA HIGHLANDER RUNNING BOARD HIGHLANDER HV Preparation
Preparation Part Number: PT738-48080 Kit Contents Item # Quantity Reqd. Description 1 1 Driver Side Running Board 2 1 Passenger Side Running Board 3 4 /Middle Mount Bracket 4 2 Rear Mount Bracket 5 2 Rear
More informationWPS-104 Heater. Installation Instructions
WPS-104 Heater Installation Instructions For 2007 vehicles see page 15 WPS 104 HEATER SYSTEM INSTALLATION INSTRUCTIONS If this is a complete installation of top, windshield and heater system, for ease
More informationMustang Clear Lens Instrument Cover (90-93) - Installation Instructions
Mustang Clear Lens Instrument Cover (90-93) - Installation Instructions The below installation instructions work for the following products: Mustang Clear Lens Instrument Cover (90-93) Please read through
More informationInstallation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips Intellivue MP5/20/30 VHM-25 Channel Mount Kit Install Time: 10-15 minutes The
More information800 Deere Rd. Prescott, WI CertiSafe Floor Mount
800 Deere Rd. Prescott, WI 54021 715-262-4488 sales@kascomarine.com www.kascomarine.com CertiSafe Floor Mount Table of Contents Parts Included Page 3 Tank Penetration. Page 5 Base Assembly.. Page 8 Retrieval
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More informationTOYOTA TACOMA HANDS FREE BLU LOGIC Preparation. Item 5 Item 6 Item 7 Item 8. Item 4. General Applicability Note: Recommended Tools
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00098 Conflicts: JBL Audio, Factory Navigation Kit Contents: NOTE: Part number of this accessory may not be the same as the part number
More informationGeneral Applicability Note: Recommended Tools. Personal & Vehicle Protection Safety Goggles Seat Covers Floor Covers Special Tools. Installation Tools
TOYOTA HIGHLANDER/HIGHLANDER HV 2008- Preparation Part #: PT923-00111 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: Accent light Kit APPLICATION: R42H (2011) PART NUMBER: 999F3 AW000 - Universal Accent Lighting Kit. KIT CONTENTS: Item QTY Description Service
More informationHP BladeSystem c7000 Carrier-Grade Options Installation Guide
HP BladeSystem c7000 Carrier-Grade Options Installation Guide Part Number 5991-8062 September 2009 (Second Edition) Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein
More informationA Fitting Guide for the Forge Motorsport Front Mounting Intercooler for the BMW Mini Cooper S Turbo R56 Models
A Fitting Guide for the Forge Motorsport Front Mounting Intercooler for the BMW Mini Cooper S Turbo R56 Models (A copy of this guide is available online, in the media section of our website) A general
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: DUAL DVD HEADRESTRAINT MONITOR Pathfinder - (204 Above S grade, without factory FES, and VINs ending in less than 650298)
More informationZeon Control Pack Relocation Kit 78 Cable Length
ORIGINAL INSTRUCTIONS SYMBOL INDEX SYMBOL EXPLANATION SYMBOL EXPLANATION Read All Product Literature Always Wear Leather Gloves Always Wear Hearing and Eye Protection Do Not Move People Zeon Control Pack
More informationSCION XB HANDS FREE BLU LOGIC Preparation. Item 4 Item 5 Item 6 Item 7. General Applicability. Note: Recommended Tools
SCION XB 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00090 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: Item 1 Item 2 Item
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 200-2014 Ford Expedition / 2007-2014 Ford Expedition EL 200-2014 Lincoln Navigator L 2/4WD 2009-2014 Ford F-150 2015 + Ford
More informationGN-3A Polaris General SSV Works 3 Speaker Audio Kit
GN-3A Polaris General SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 17 Kick Panel Speakers Installation pg 21 MRB3 and Dash
More informationDVS Cypress Face Installation Instructions (SKU )
Table of Contents Compatibility... 1 Packing List... 1 Installation... 2 Prepare the Insert for Face Installation... 2 Attach the Surround Panels (if applicable)... 6 Assemble the Face... 7 Attach the
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: DUAL DVD HEADRESTRAINT MONITOR Pathfinder - (204 Above S grade, without factory FES, and VINs ending in less than 650298)
More information58-62 Corvette Manual Rack & Pinion Kit Instructions #
58-62 Corvette Manual Rack & Pinion Kit Instructions # 8001550 Unisteer offers a limited warranty against all manufacturer defects of their kits and supplied parts. Unisteer will not honor any warranty
More informationINSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274
INSTALLATION INSTRUCTIONS JEEP 2011-UP JK SECURITY FULL CONSOLE #274 PARTS CHECKLIST Tuffy Console #9 Left Front Mounting Bracket #10 Right Front Mounting Bracket #11 Electronics mounting bracket #12 Divider
More information(31 ) ZEON CONTROL PACK RELOCATION KIT
ORIGINAL INSTRUCTIONS SYMBOL INDEX (31 ) ZEON CONTROL PACK RELOCATION KIT SYMBOL EXPLANATION Read All Product Literature SYMBOL EXPLANATION Always Wear Leather Gloves INSTALLATION GUIDE Always Wear Hearing
More informationLEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-30120 (GS350) PT922-30130 (GS450h) NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents Item # Quantity Req'd. Description 1 1 Illuminated
More informationTOYOTA SOLARA CONVERTIBLE XM SATELLITE RADIO Preparation. Part Number: Mounting Kit PT
Preparation Part Number: Mounting Kit PT546-06061 Tuner Assy 86180-0W030 Tuner Assy Kit Contents (86180-0W030) 1 1 Tuner Assy, Stereo Component Mounting Kit Contents (PT546-06061) 1 Ground Cable 1 1 Wire,
More informationHow to remove and replace the Foonf/Fllo fabric
How to remove and replace the Foonf/Fllo fabric Remove Headrest Locate the Troubleshooting Tool behind the manual on the back of the car seat, as shown in Figure 1. Raise Headrest to highest position by
More informationOwner s Manual Electric Swivel
12-225- 11/6/17 1 of 22 Owner s Manual Electric Swivel Onboard Systems International 13915 NW 3rd Court Vancouver, WA 98685 United States of America Cage Code: 1Y921 Toll Free Phone: (8) 275-883 Phone:
More informationP3066 INSTALLATION MANUAL
P3066 INSTALLATION MANUAL Parts List 1 Grille guard 1 Driver / left frame bracket Level of Difficulty Moderate Scan for helpful install tips 1 Passenger / right frame bracket 1 Driver / left top bracket
More informationMF 9520 / 9540 / 9560, Challenger 540C / 560C
Ag Leader Combine Installation Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number 9520 Quantity by Model 9540 540C Parts Kit 2001312-69 1 1 1 Drill
More informationKeeping You Cool Under Pressure
Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal
More informationGP1-R FULL EXHAUST SUZUKI GSX-R600 / GSX-R
THIS EXHAUST SYSTEM IS DESIGNED FOR USE IN CLOSED COURSE RACING ONLY, AND IS NOT INTENDED FOR PUBLIC HIGHWAY USE. IN THE STATE OF CALIFORNIA, IT IS ILLEGAL TO MODIFY THE EMISSION CONTROL SYSTEM ON ANY
More informationLankota, INC. LAN Installation Instructions
Lankota, INC. LAN - 84206 Converts 600 Series Platform Heads to 50 Series & Earlier Model Combines. Installation Instructions Kit LAN84206 Lankota is the trademark of Lankota, Inc. 1 LAN 84206 Parts break
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.
Installation Instructions RT8RT/RT5RT Relight Assembly READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION. IMPORTANT SAFETY INSTRUCTIONS WARNING: FAILURE
More informationSCION xb OVERHEAD CONSOLE Preparation. Part Number:
SCION xb 2008 - OVERHEAD CONSOLE Preparation Part Number: 08253-12800 Kit Contents Item # Quantity Reqd. Description 1 1 Overhead Console 2 1 Bracket 3 1 Plastic cover 4 1 Photo Mount Sheet 5 1 Installation
More informationInstallation Instructions BR20 Rear Bumper Replacement Part # 28178T Toyo ta Tundra 2/4WD
Installation Instructions BR20 Rear Bumper Replacement Part # 28178T 2014-2016 Toyo ta Tundra 2/4WD Excludes Models with B lind Spot Monitoring & Cross Traffic Alert Parts List Item Qty. Part # Description
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Electronic Tailgate Lock Kit Nissan Titan 999M2-W3005 KIT CONTENTS: Item Qty. Part Description Service Part Number A 1 Electronic
More informationCATALOG OF REPLACEMENT PARTS W32/W32C/625A WRAP STATION ML-44103, ML ML-44105, ML ML-26243
CATALOG OF REPLACEMENT PARTS W32/W32C/625A WRAP STATION W32 W32C 625A HP ML-44103, ML-26320 ML-44105, ML-26331 ML-44069 ML-26243 A product of HOBART CORPORATION 701 S. RIDGE AVENUE TROY, OHIO 45374-0001
More informationSCION XB SUBWOOFER ENCLOSURE Preparation
Preparation Part Number: Kit Contents Item # Quantity Reqd. Description 1 1 Subwoofer enclosure 2 1 Wire Harness 3 1 Paper Template 4 1 Plastic Drill Template 5 1 Hardware Bag Hardware Bag Contents 1 Item
More informationSCION TC HANDS FREE BLU LOGIC Preparation
SCION TC 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00099 Conflicts: JBL Audio NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents: For kits manufactured
More informationAssembly Guide ELECTRIC. Model Numbers: C1. (English) /14/11
Assembly Guide Model Numbers: 12601559 12601578 12601663 12601664 12601665 12601688 12601514 12601514-C1 ELECTRIC (English) 42804641 09/14/11 2 ASSEMBLY GUIDE A, B, C, Assembly: CAUTION: For your safety,
More informationDown and Out Motor Mount Assembly & Installation Directions
Down and Out Motor Mount Assembly & Installation Directions Mounting the Down and Out Motor Mount correctly takes a lot of thought and a lot of planning. Please read the directions thoroughly and plan
More informationTOYOTA SIENNA TRAILER WIRE HARNESS Preparation
Preparation Part Number: PT791-08150 (non-se) PT791-08102 (SE only) Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Module Harness 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting
More informationInstallation Instructions for the Vision SLR Lightbar with the Hook-On Mounting Kit
Installation Instructions for the Vision SLR Lightbar with the Hook-On Mounting Kit 2562541A REV. A 1210 Safety Message to Installers of Federal Signal Warning Light Systems People s lives depend on your
More informationMODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.
502-2 & 503-2 Instructions instructions marinco.com Installing and Using the Precision Spotlight MODELS: SPL-12W, SPL-12B, SPL-12C IMPORTANT! READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.
More informationChecker Unload Checkstand Installation Instructions
Front-End Checkouts Commercial Refrigeration Equipment Display Merchandisers Store Fixtures Checker Unload Checkstand Installation Instructions Attention Store Manager: Please find enclosed in this packet
More informationINSTALLATION INSTRUCTIONS AM rev. A
INSTALLATION INSTRUCTIONS AM16629-1 rev. A READ THIS MANUAL CAREFULLY! FAILURE TO INSTALL THIS EQUIPMENT PER THESE INSTRUCTIONS WILL VOID THE WARRANTY. INTRODUCTION NOTE: Zebra technologies Corporation
More informationInstallation Guide. Before Starting. Package Contents. Cautions On Installation. English
Before Starting Car battery. This set is exclusively for use in cars with a negative ground, V power supply.. Read these instructions carefully.. Be sure to disconnect the battery terminal before starting.
More informationSPECIALTY TOP CO. STC. INSTALLATION INSTRUCTIONS TOYOTA FAST TRAC Z TOP Toyota FJ PART #222-31X 82 1/8" 82 1/8"
STC INSTALLATION INSTRUCTIONS TOYOTA FAST TRAC Z TOP Toyota FJ-40 1963-1983 PART #222-31X SPECIALTY TOP CO. Thank you for purchasing Specialty's Convertible Top for your Toyota. It has been designed for
More information