ITR Compressor Bleeder #1 Bleeder #1 + Bracket Bleeder #1 Bleeder #1 + Bracket Bleeder #2 Bleeder #2 + Bracket 10315

Transcription

1 Affected Model(s): Effective Date: Nov 16, 2010 Effective Serial Number: Description: CO32, CO45, SCH25, H2, H2L, HWH, CH50 N/A Compressor replacement Short description of change: The Dynaflow compressor will be used to replace compressors in the CO32, CO45, SCH25, H2, and HWH. Note that the air bleeder installed on the outlet of the compressor for these heaters will change based on the table below: Heater model SCH25 CO32 CO45 XL45 CO65 H2 HWH H2L CH50 Standard Thomas Compressor ITR Compressor Bleeder #1 Bleeder #1 + Bleeder #1 Bleeder #1 + Bleeder #2 Bleeder #2 + No bleeder No bleeder + No bleeder No bleeder + Bleeder #2 Bleeder #2 Bracket 33033revG Bracket 33033rev H Bleeder #2 Bleeder #2 Bracket revg Bracket rev H No bleeder No bleeder Bracket revg Bracket rev H No bleeder No bleeder Bracket revg Bracket rev H Dynaflo Low DC Bleeder #2 + Bleeder #2 + X Combi No bleeder No bleeder X X X Dynaflo High #3032 Bleeder #2 + Bleeder #2 + X Page 1 of 9

2 Bleeder hole location Bleeder #1 = #63 drill for nozzles (PINK DOT) Bleeder #2 = #70 drill for nozzles (orange dot) Thomas Compressor Dynaflo Compressor *Low version has number DC *High output has number DC and label #3032 attached ITR Compressor Page 2 of 9

3 CO32/45 and SCH25 COMPRESSOR CHANGE PROCEDURE 1 Tools needed: 1. Philips head screw driver -Turn off the heater - open side cover - locate three screw on top besides the air intake collar. - unscrew them and hold compressor so it doesn t fall down - release hose by removing hose clamps Page 3 of 9

4 - Attach rubber feet to bracket (10315) -Install compressor in same position. Make sure a bleeder is installed for the CO32 and SCH25 models before attaching the hose. Page 4 of 9

5 H2 and HWH DYNAFLO COMPRESSOR CHANGE PROCEDURE 1 Tools needed: 1. Philips head screw driver -Turn off the heater - open front cover - take out compressor and bracket from burner box - screw dynaflow onto the bracket (10315) using two #8-32 screws Page 5 of 9

6 Re-install compressor on burner box Page 6 of 9

7 TECHNICAL BULLETIN November 16, 2010 Heating Systems Bulletin Identification No.: MTB ITR COMPRESSOR CHANGE PROCEDURE When exchanging a Thomas or Schmaltz compressor with an ITR compressor you have to pay attention to the mounting bracket. ITR BRACKET THOMAS BRACKET The Thomas bracket (33033rev G) can be recognized by the hole positioned at the right hand side. THOMAS BRACKET (33033 rev G) The ITR compressor bracket (33033rev H) has the hole positioned in the center. ITR BRACKET (33033 rev H) The ITR compressor is mounted with 2 screws in the front housing. If the wrong bracket is used, the compressor motor might hit the combustion fan. Page 7 of 9

8 Combi COMPRESSOR CHANGE PROCEDURE 1 Tools needed: 2. Philips head screw driver -Turn off the heater - open front cover - take out compressor and bracket from burner box - install dynaflo on modified bracket as shown in picture. - install 45 deg elbow on outlet. Page 8 of 9

9 - screw dynaflow onto the bracket (10315) using two #8-32 screws Page 9 of 9