FiberTwist + Pulse. Network Termination + WiFi Repeater/Extender Quick Installation Guide

Transcription

1 FiberTwist + Pulse Network Termination + WiFi Repeater/Extender Quick Installation Guide

2 Unlock button 1. Preparation The installation of your FiberTwist and Pulse combination starts with the FiberTwist. After installing the FiberTwist, the next steps of connecting the Pulse can be followed from step 6. Ensure there is a power socket within 80cm of where your FiberTwist is being installed. 2. Remove the FTU blind cover Press and hold the unlock button (on the right side at the top of the blind cover). Rotate the blind cover counter clockwise. When it won t rotate any further, the blind cover can be removed by pulling it towards you. Please store the blind cover in a safe place. Important: It is crucial the next steps for the installation of your FiberTwist all be completed in one go. Failure to do so could result in damage to the fiber optic connectors, causing a severe degradation of signal quality. It is assumed that the Fiber Termination Unit (FTU) is already installed in the meter cabinet or mounted on a wall.

3 Dust cap 3. Remove dust cap of FiberTwist Take your FiberTwist out of its box. The dust cap is the bright red tab located on the rear of your FiberTwist. Remove the dust cap by holding the end of the red tab and pulling it gently in the direction of the arrow. Please store the dust cap (along with the blind cover) in a safe place. 4. Twist! Place your FiberTwist on the FTU as shown above and rotate clockwise until it clicks into place. Make sure your FiberTwist is aligned squarely on the FTU - each edge must line up directly with the FTU below. Note: If at some point in the future it becomes necessary to uninstall your FiberTwist, please place the blind cover back on the FTU immediately and put the dust cap back on your FiberTwist.

4 5. Connect to the power Connect the supplied power adaptor to your FiberTwist and then plug the adaptor into a power socket. 6. Placement of Pulse Place your Pulse within 2m* from your FiberTwist, preferably not in the meter cabinet. Ensure there is a power socket within 1m of where your Pulse is being installed. Your Pulse can be placed on a desk, or it can be mounted on a wall using the wall mount points on the back of the device. The Drilling Template can be downloaded from the Genexis website at: *2m Ethernet cable is included. Depending on your home, a longer cable can be used to place the Pulse further into the home.

5 7. Connect Pulse to FiberTwist Connect the provided Ethernet cable to a LAN port of your FiberTwist and to the WAN (red) port of your Pulse. 8. Connect to the power Connect the supplied power adapter to your Pulse and plug the adapter into an AC power socket. If the LED behavior that you see (of your Pulse) is not consistent with what is mentioned in this QIG then perform a factory reset of your device.

6 SSID: Genexis-xxxx WiFi-Key: ************** Power switch Model: Pulse P/N: Version: 1.0 Date: WARNING: POWER RATING:12V GUI: Username: user Password: user Made in China 2A 9. Turn on your Pulse Turn on your Pulse by flipping the switch on the side of the device. After approximately 1.5 minutes the Status LED should turn green and stop blinking. When the Internet LED becomes yellow, your Pulse is ready for use. 10. Connect to your Pulse WiFi Consult the information label at the bottom of your Pulse. It shows the SSID of the WiFi network (i.e. GENEXIS-xxxx) and the WiFi Key. Connect to this WiFi network with your devices. You are now connected to the internet. For more information about your Pulse or your FiberTwist, have a look at the Full Installation Guides ( download-portal/#fibertwist)or or contact your service provider. Hereby, Genexis declares that the radio equipment type Pulse is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: Revision October 2018 Copyright 2018 Genexis B.V. All rights reserved.