DATA PD-214-F101. TEBS G2 Doc. No. Y (EN - Rev. 001) July Product. Lift Axle Control. Function. Operation
|
|
- Winifred Simmons
- 5 years ago
- Views:
Transcription
1 Commercial Vehicle Systems Product DATA Function Many trailers have one or more axles having the capability of being lifted so that they carry none of the trailer load. The function is present in the TEBS Brake Module to provide control of the lifting of these axles. TEBS G Doc. No. Y8 (EN - Rev. 00) July 0 Doc. No. Y8 (EN - Rev. 00) July 0 PD--F0 Operation (LAC) The TEBS Brake Module can control the lift axles automatically dependent on the current axle/bogie load and the predefined lift axle control parameters. If RSP is configured and the trailer is equipped with lift axles, these axles must be controlled by the TEBS G Brake Module or their status must be transmitted to the module via the ext LAS input. To achieve lift axle control, one or more lift axle valves should be connected to one of the AUXIO outputs, or for electrically switched lift axle valves and auxiliary output port P 8 for pneumatically switched lift axle valves. See PD-0-00, Document No. Y00 for details of lift axle valves. The following parameters associated with lift axle control may be defined by using the Knorr-Bremse brake calculation program BSD or the Knorr-Bremse diagnostic program ECUtalk using the Components tab then the Change configuration option: Number of lift axles Location of lift axles Number of lift axles that are controlled via one Aux output (there are two controllable outputs, LAC and LAC) Note - LAC must be configured first Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
2 PD--F0 TEBS G Product Data Doc. No. Y8 (EN - Rev. 00) July 0 TEBS G.0 / G. / G. Standard Using the Auxiliary I/O tab and Change Configuration, select the required AUXIO then enter: the maximum axle/bogie load at which the lift axle should be lowered (see page ) the axle/bogie load at which the lift axle should be lifted TEBS G. Standard Plus Using the Auxiliary I/O tab and Change Configuration, select the Lift Axle option, then select the required AUXIO output. When this has been done, enter: the maximum axle/bogie load at which the lift axle should be lowered (see page ) the axle/bogie load at which the lift axle should be lifted Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
3 Commercial Vehicle Systems Doc. No. Y8 (EN - Rev. 00) July 0 TEBS G PD--F0 The function of lift axle control is dependent on the air spring pressure. This is continuously monitored by the TEBS Brake Module and used to determine the respective axle/bogie loads based on the configured laden and unladen axle loads and the number of axles. Normally only an axle which is not equipped with wheel speed sensors may be configured as a lift axle, except in the case of: S/M configurations (G.0 and G. only) when the axle on which wheel speed sensors connected to S-E and S-F are installed may be used as a lift axle. S/M configurations on semi-trailers and centre-axle trailers (G.0 and G. with TEPM-S or TEPM-P) when the axle on which wheel speed sensors connected to S-A and S-B are installed may be used as a lift axle. S/M configurations on semi-trailers and centre-axle trailers (G.0 and G. with TEPM-s or TEPM-P) when the axle on which wheel speed sensors connected to S-A and S-B and/or S-E and S-F are installed may be used as a lift axle. Failure to follow this requirement will result in a fault being generated when a lift axle is raised. The status of the lift axle is transmitted to the towing vehicle via the ISO 99 (CAN) interface when the trailer is coupled to a towing vehicle which is equipped with EBS. In such cases it is also possible that the lift axles are controlled from the towing vehicle via the same interface. As the trailer load decreases the first axle to lift must be controlled by LAC. Important: When the trailer suspension control system is two circuit it is important that the connection from the air springs to port of the TEBS Brake Module is taken from the circuit NOT containing the lift axles. Failure to observe this requirement may lead to lift axle instability. The connection from the air suspension system to port should always be chosen carefully so that the lifting or lowering of axles does not significantly affect the pressure in port. Number of lift axles that can be controlled via one AUXIO output It is possible, by using the correct cable harness, to connect two electrically controlled lift axle valves to one AUXIO output; the lift axles will then operate simultaneously. In the same way, more than one pneumatically controlled lift axle valve may be connected to Aux P 8. Determination of the axle load at which the lift axle should be lowered When defining the lift axle control parameters using the diagnostic program ECUtalk (see above), the axle/bogie load at which the lift axles will lower is, by default, the laden axle/bogie load permitted for the trailer - otherwise the axles remaining on the ground would be overloaded. It is possible to configure a lower value than the laden axle/ bogie load, for example to comply with specific national axle loading requirements. Tip: When the trailer is loaded with a large individual load, in order to prevent temporary overloading of an individual axle, the axle/bogie load at which the lifted axles are lowered should be set to a value below the maximum value. Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
4 PD--F0 TEBS G Product Data Doc. No. Y8 (EN - Rev. 00) July 0 Hysteresis When setting the lift axle parameters for the TEBS Brake Module, it is required to define the position of the lift axle and the number of lift axles controlled by LAC or LAC (see above). This effectively defines the lifting sequence since LAC is always the first axle to lift. In addition it is required that the geometric data of the wheelbase and axle spread is defined, therefore, it is not necessary to define a hysteresis value as this will be calculated automatically using the information above. The diagnostic program ECUtalk, and brake calculation program BSD, will automatically calculate the maximum axle/bogie load at which the axle(s) should lift. It is possible to define a lower axle/bogie load than the default maximum but not higher (hovering the mouse over the weight boxes will display the maximum and minimum programmable values). This calculation takes into consideration a factor which ensures that, irrespective of the position or lifting sequence of the lift axles, or the wheelbase of the trailer, the defined axle lifting loads will ensure that overloading does not occur and the lift axles remains stable. Initiation of lift axle control By means of the diagnostic program ECUtalk, it is possible to define whether the lift axle control should be active when the trailer is stationary and the ignition is switched ON, i.e. the lift axle would raise - provided the load state allows this, or whether the lift axle control should begin only when a speed threshold is exceeded. The thresholds are: TEBS G.0/G./G. Standard Yes - lift axle control is enabled at standstill and all speeds. No (Enable at any speed) - this is the speed at which the wheel speed sensor outputs are detected. No (enable at configured SP speed) - this is TEBS G. Standard Plus linked to the Speed Pulse (SP) which has a default switching speed of km/h. This default will apply in the event that either no SP function is configured, or the SP speed is not changed from the default value. If the SP speed is changed, for example to 0 km/h, then lift axle control will not commence until after this speed has been reached. By linking the lift axle control to the SP speed it is ensured that the suspension is reset to the driving condition before any lift axle control commences. This is desirable as the air spring pressure measured by the TEBS Brake Module may not be representative of the load condition during operation of the raise/lower valve. Once the lift axle is lifted, irrespective of whether at standstill or after the SP speed, it will remain so until either a higher loading state is detected or a lower lift axle control is activated which can take place electrically or pneumatically or the ignition is switched OFF. This means that the option Lift axle active at standstill relates only to the period that the trailer is stationary immediately after switching ON the ignition. When the TEBS Brake Module has an electrical AUXIO configured to Speed Pulse (SP) and raise / lower valve SV80 is connected, the maximum duration of the Speed Pulse signal must not exceed the default setting of seconds otherwise overheating of the module ECU may occur. Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
5 Commercial Vehicle Systems Doc. No. Y8 (EN - Rev. 00) July 0 TEBS G PD--F0 The priority of lift axle control relative to other functions is shown below: Priority Function Description Highest Auxiliary Design Language (ADL) Lowest Activation of a function will override any action requested by a function with a lower priority ISO 99 or J99 CAN commands Driver request ISO 99 CAN ATC status icorner icargo Automatic (LAC) An ADL program may override any calculated lift axle state. A command such as Raise or Lower a lift axle will disable all lower priority functions. Driver request via a connected manual switch input such as Traction Help or via use of the service brakes. ATC Active will cause an automatic Traction Help request. An icorner command will override any icargo or Automatic command. An icargo command will override any Automatic Lift Axle Control command. If no other request is active then the Automatic Lift Axle Control will take control of the lift axles. Lift axle control is automatically disabled if the pressure in the air bags falls below % of the configured unladen pressure or if the reservoir pressure falls below. bar. Lower Lift Axle (LL) Forcing a lifted axle to lower when the automatic control dictates that it should be in the lifted position is often a desirable function, e.g. to assist manoeuvring, and has been integrated in the TEBS Brake Module. It can be realised by any of the following methods:. Tri-state inputs via single wire connection to either pin or where the following conditions will be recognised as requiring Lower Lift axles : Change of state open circuit to / V Change of state open circuit to ground. AUXIOs, and require a -wire connection (with their respective return lines) to recognise a change in state from open to short circuit or short circuit to open circuit.. Inputs S-E and S-F (TEBS G.0 and G. S/M and S/M configurations only) may be used with a -wire connection, as above, or as tri-state inputs, as above (with the two connections linked).. Activation via actuation of the brakes.. Manual operation via the Trailer Information Module (TIM G). Signal transmitted from the tractor via a specific message request included in ISO 99 (CAN) data communications. A signal received via the ISO 99 communications data link will take priority over normal lift axle control signals (see table above). Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
6 PD--F0 TEBS G Product Data Doc. No. Y8 (EN - Rev. 00) July 0 When a switched voltage signal or a ground signal is used, the associated switch may be of the momentary type (non-latching) or permanent type (latching) and the TEBS G Brake Module will automatically recognise the single change in state. If a momentary switch is used then the _M function must be configured and if a permanent switch is used the _P function must be configured. Lower All Lift Axles (LL_ALL_M and LL_ALL_P) This function lowers all lift axles when the switch is activated and overrides any normal lift axle control present (see table above). Lower All Lift Axles controlled by LAC (LL_LAC_M and LL_LAC_P) This function lowers all lift axles controlled by LAC when the switch is activated. Lower All Lift Axles controlled by LAC (LL_LAC_M and LL_LAC_P) Notes: Switch type used Momentary (non-latching) Permanent (latching) Functions available LL_ALL_M LL_LAC_M LL_LAC_M LL_ALL_P LL_LAC_P LL_LAC_P This function lowers all lift axles controlled by LAC when the switch is activated. Select ECUtalk option G.0/./. Standard G. Standard Plus Input momentary switch Input permanent switch Momentary Permanent After selection of Lower Lift axle as described above by means of a momentary switch, the lift axle control will remain disabled unless the switch is pressed again or Traction Help is selected or the ignition is turned off. When a permanent switch is used its selection will result in the lift axle being lowered. To re-activate Lower Lift axle the switch must first be deactivated before a second actuation is possible. TEBS G.0/G./G. Standard TEBS G. Standard Plus Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
7 Commercial Vehicle Systems Doc. No. Y8 (EN - Rev. 00) July 0 TEBS G PD--F0 Advanced (LLTH) This is a combined function which offers the Traction Help (see PD--F0, Document No. Y9) and lift axle lowering via the same input. The following logic is implemented (for momentary switch only supplied through spare pin in the ISO or ISO 098 connector): - signal active for less than seconds = Traction Help - signal active for more than seconds and less than 0 seconds = Lift Axle Lower - signal active for more than 0 seconds = will be ignored, TEBS stays in normal lift axle control mode. With TEBS G.0/G./G. Standard the switch must be selected as momentary. With TEBS G. Standard Plus the switch defaults to momentary and does not allow any change. TEBS G.0/G./G. Standard TEBS G. Standard Plus Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
8 PD--F0 TEBS G Product Data Doc. No. Y8 (EN - Rev. 00) July 0 via operation of the service brakes Activation of lift axle control ( Lower Lift axle and Traction Help - see PD--F0, Document No. Y9) via actuation of the brakes is a standard feature within the TEBS G Brake Module therefore no additional wiring or system configuration is necessary only configuration of a lift axle is required. To realise the Lower Lift axle function via brake actuation the following criteria must be fulfilled: p [bar].0 0. The vehicle must be stationary with the ignition t s 8s ON. TEBS-G-0 If the towing vehicle is connected via a pin ISO 8 connector no brake application is made from any source (hand brake or foot brake) for a period of seconds. If the towing vehicle is connected via a pin ISO 8 connector no ISO 99 (CAN) brake application is made, irrespective of whether a pneumatic braking demand is present or not, for a period of seconds. Then within a period of 8 seconds, brake applications must be made where the braking demand must exceed bar and then fall to below 0. bar on each application. The figure graphically illustrates the characteristic. This lift axle control function via brake actuation is enabled by default but can be turned off under the Miscellaneous tab and Change configuration. ADL files (see PD--F90, Document No. Y) are available that are able to provide different lift axle control functionality to that described above. Recommended Valves for Part No. Type No. Operation K00 #) * K08 #) K0 #) AE Ports,,, Port V Solenoid M x. M x. V Solenoid Air operated K0988 #) V Solenoid *** PTC** for R8x M x. with exhaust valve For further details on these valves see PD-0-00, Document No. Y00 #) Part No. will carry the suffix N00 denoting that it is supplied without packaging * Replaces valves K008 and K0 ** PTC = push-to-connect *** this valve needs to be connected to AUXIO or. The output voltage for these connections has to be set to V. This is necessary to protect the V solenoid against overheating. Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
9 Commercial Vehicle Systems Doc. No. Y8 (EN - Rev. 00) July 0 TEBS G PD--F0 Typical Wiring Diagram - TEBS G. with electrical LAC and LAC outputs S-D ISO 8 LAC LAC RD BN WH WH/GN WH/BN RD BN WH WH/GN WH/BN 8 V_VALVE V_ECU GND_H GND_M WL V-CAN-H V-CAN-L AUX IO AUX IO AUX IO In-Out SENS_Sup / TriState SENS_In / TriState SENS_GND Brake-Light V Brake-Light GND S-F Power TEBS G. - ECU 9 V-CAN-L 0 V-CAN-H AUX IO - RET AUX IO - RET ISO 8 S-C S-E TEBS-G-0 Typical Wiring Diagram - TEBS G. with electrical LAC and LAC outputs ISO 8 LAC LAC RD BN WH WH/GN WH/BN RD BN WH WH/GN WH/BN V_VALVE V_ECU GND_H GND_M WL V-CAN-H V-CAN-L AUX IO AUX IO AUX IO SENS_GND In-Out SENS_In / TriState SENS_Sup / TriState Brake-Light V Brake-Light GND V-CAN-L V-CAN-H Power TEBS G. - ECU AUX IO - RET AUX IO - RET ISO 8 S-C S-D TEBS-G.-0 Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
10 PD--F0 TEBS G Product Data Doc. No. Y8 (EN - Rev. 00) July 0 Typical System Diagram - pneumatic LAC output "Supply" 8 "Control" ISO 8 (N) ECU KNORR-BREMSE TEBS G Lift Axle Valve ISO 8 (Pin) For more information on ECUtalk use the on-line help function by pressing F or see the Product Information Document No. Y09 available at For further guidance on using a lift axle with TEBS see the Installation Instructions Document No. Y89 available at This document forms part of the Product Manual for the TEBS G Family, Document No. Y0 Revision Details Rev. 000 September 0 New document Rev. 00 December 0 Document amended to include different ECUtalk screenshots when using TEBS G. Standard Plus. Table of recommended valves added to page 8. Rev. 00 July 0 Correction - wheel speed sensor configurations on page amended. Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
DATA PD-214-F104. TEBS G2 Doc. No. Y (EN - Rev. 001) May Product. icargo. Function. Operation
Commercial Vehicle Systems Product DATA Function On semi-trailers and centre-axle trailers, the axle/bogie will act as a pivot point that, depending on the positioning of the cargo carried by the trailer,
More informationLift axle control on axle 1. Lift axle control on axle 3
Commercial Vehicle Systems Product DATA Function On vehicle combinations using semi-trailers it is often difficult to meet the turning corridor required by European Community (EC) legislation. When certain
More informationDATA. icargo) Product. Application. Purpose. Function. Knorr-Bremse s intelligent axle loading system, icargo, is designed to work on:
Commercial Vehicle Systems Product DATA Doc. No. Y09 (EN - Rev. 00) January 0 Application Knorr-Bremse s intelligent axle loading system,, is designed to work on: Semi-trailers with two to five axles Centre-axle
More information1. Semi- and centre-axle trailers To enable the automatic load sensing function to operate, it is necessary to define certain parameters as follows:
Commercial Vehicle Systems Product DATA Function Load Sensing Function (pneumatic suspension) PD-4-F00 The Load Sensing Function (LSF) of the TEBS Brake Module is used to replace the function of a load
More informationDATA PD AE1141 Lift Axle Valves - TEBS controlled. P r o d u c t
C o m m e r c i a l V e h i c l e S y s t e m s P r o d u c t DATA AE Doc. No. Y05067 (Rev. 00) August 0 PD-50-00 Function The TEBS controlled Lift Axle AE Valve is used for trailers with electronic braking
More informationDriving Position. Raise/Lower Position. Adaptor Plate* 19 min
Commercial Vehicle Systems Product DATA Raise/Lower Valves (single circuit) Doc. No. Y0377 (EN - Rev. 003) October 0 PD-501-050 Function Raise/Lower Valves are fitted on vehicles with air suspension and
More informationDATA PD BR43.. Load Sensing Valve - mechanically controlled. Product. Function. Technical Features. Range Overview
Commercial Vehicle Systems Product DATA BR.. Doc. No. Y0 (EN - Rev. 00) May 0 PD-0-000 Function The Load Sensing Valve is used to adjust the applied service brake pressure in relation to the load imposed
More informationWeight Stroke TÜV-Inspection approx. [kg] II )4) BZ M16x Port threads:
Commercial Vehicle Systems Product DATA Spring Brakes (S-cam), diaphragm/piston Doc. No. Y1137 (EN - Rev. 5) September 216 PD-413-1 Function This range of Spring Brakes is used on axles fitted with drum
More informationTrailer brake and chassis control
COMMERCIAL VEHICLE SYSTEMS BRAKE AND CHASSIS CONTROL Trailer brake and chassis control TRAILER COMPETENCE 2 THE MUNICH-BASED KNORR-BREMSE GROUP IS THE WORLD S LEADING MANUFACTURER OF BRAKING SYSTEMS FOR
More information. For 4S/3M applications an Integrated Speed Switch (ISS)
Commercial Vehicle Systems Product DATA PD-203-430 Function The Knorr-Bremse KB4TA module is an integrated ABS electronic control unit and dual modulator valve for air braked trailers (semi-trailers, centre-axle
More informationEBS and More. What can you do with advanced braking systems? Chair : Mario Colosimo. Robert Smedley, Knorr Bremse Ian Thomson, BPW Transpec
EBS and More What can you do with advanced braking systems? Chair : Mario Colosimo Panel : Neil Chilton, Warnambool Cheese and Butter Robert Smedley, Knorr Bremse Ian Thomson, BPW Transpec Trailer Electronic
More informationFeatures: ECUtalk enables the user to:
Features: ECUtalk enables the user to: Retrieve information from the ECU: - General - Error status - Configuration Change the ECU s configuration Check System components Carry out EOL tests Generate Load
More informationDATA PD ES1305. Product. Trailer ABS (KB4TA) Function
V Commercial Vehicle Systems Product DATA PD-203-300 Function The Knorr-Bremse KB4TA module is an integrated ABS electronic control unit and dual modulator valve for air braked trailers with mechanical
More informationDATA PD LS1..., LS2..., LS3... Lift Axle Valves - Pneumatic. P r o d u c t. Function. Technical Features
C o m m e r c i a l V e h i c l e S y s t e m s P r o d u c t DATA PD-503-200 Function Pneumatic Lift Axle Control Valves are used for the semi-automatic or fully automatic control of air suspended lift
More informationFunction ECU, Wireless
Commercial Vehicle Systems Product DATA PD-551-000 Function ECU, Wireless The is a Gateway Receiver system to alert the driver if any monitored tyre runs under its normal pressure or above its normal temperature.
More informationFunction ECU, Wireless
Commercial Vehicle Systems Product DATA PD-551-000 Function ECU, Wireless The is a Gateway Receiver system to alert the driver if any monitored tyre runs under its normal pressure or above its normal temperature.
More informationDATA PD VB... Air Reservoirs. Product. Function. Technical Features. Range Overview - mounting straps for steel and aluminium reservoirs
Commercial Vehicle Systems Product DATA Doc. No. Y095687 (EN Rev. 004) February 16 PD50 Function are used to store the compressed air for the vehicle air braking, suspension and auxiliary systems. They
More informationOperator's Guide ELECTRONIC BRAKE SYSTEMS DIAG+
Operator's Guide ELECTRONIC BRAKE SYSTEMS DIAG+ www.haldex.com Content Contents Introduction Minimum System Specification Page 2 Installation Options Page 3 ECU Connnections Page 4 Secondary Displays Page
More informationDATA PD AE431. Product. Park/Shunt Valves with Integrated Emergency Function. Function
Commercial Vehicle Systems Product DATA Park/Shunt Valves with Integrated Emergency Function PD-113-0 Function The Park/Shunt Valve is used on trailers that are equipped with spring brakes. It is connected
More informationTrailer EBS E Trailer EBS E with TCE
. Date Copyright WABCO Signature Information Document Compiled Trailer EBS E 2008-05-20 Barlsen 2008-05-20 Stender Stender Checked Expert ECN No. Revision Date of first issue Product Group Product Identification
More informationKnorr-Bremse Commercial Vehicle Systems. Training program, second half of 2017, Poland
Knorr-Bremse Commercial Vehicle Systems Training program, second half of 2017, Poland Information Trainings are conducted at Knorr-Bremse TruckeServices training center, Piaskowa 4/2 St., Warsaw Maximum
More informationSd Bendix TABS 6 Advanced Multi Channel Trailer ABS Module. 1. InTRodUCTIon
Sd 3 4767 TABS 6 Advanced Multi Channel Trailer ABS Module Mounting Studs -Pin ECU Cover (Sealed) ECU Covers on Both Sides (Removable) 7-Pin Mounting Studs Wheel Speed Sensor s For Port Descriptions See
More information} Rev.1/Add.12/Rev.6/Amend.3
30 December 2009 AGREEMENT CONCERNING THE ADOPTION OF UNIFORM TECHNICAL PRESCRIPTIONSFOR WHEELED VEHICLES, EQUIPMENT AND PARTS WHICH CAN BE FITTEDAND/OR BE USED ON WHEELED VEHICLES AND THE CONDITIONS FOR
More informationSD Bendix TABS 6 Advanced Single-Channel Trailer ABS Module 1. INTRODUCTION
SD-13-47671 Bendix TABS 6 Advanced Single-Channel Trailer ABS Module ECU Cover (Sealed) Through-holes for Frame (Chassis) Mounting ECU Part Number Label (See Page 34) 18-Pin Connector 3/8" NPT Load Port
More informationElectronic Function & Safety Assessment Test Report
Electronic Function & Safety Assessment Test Report Mobilität Approval Report No: EB 124.4E TÜV NORD Mobilität GmbH & Co. KG IFM Institute for Vehicle Technology and Mobility Adlerstraße 7 45307 Essen
More informationFriction Material. Freight Cars High-Speed Trains Light Rail Vehicles Locomotives Metros Passenger Coaches Regional and Commuter Trains
Friction Material Applications Freight Cars High-Speed Trains Light Rail Vehicles Locomotives Metros Passenger Coaches Regional and Commuter Trains 2 KNORR-BREMSE A FULL LINER IN FRICTION MATERIAL Our
More informationHydraulic Fluid: Master Cylinder dia. [mm]
Commercial Vehicle Systems Product DATA Function This range of Brake Chambers with Master Cylinder is used to apply the service brakes on axles fitted with hydraulic brakes. The chamber applies force to
More informationParameters Chassis. Introduction
Introduction To limit the list of parameters in this document, only parameters considered to be of use to bodybuilders are described. For full details of the current parameters for a specific vehicle,
More informationT E S T R E P O R T N o. E B E
T E S T R E P O R T N o. E B 1 8 1. 2 E on the regularity of the braking system of a vehicle in accordance with the regulations of the EC Directive 71/320/EEC or the UN-ECE Regulation no. 13 when installing
More informationDATA PD SV13.., SV14.. Levelling Valves. Product. Function. Technical Features. Range Overview
Commercial Vehicle Systems Product DATA Doc. No. Y075 (EN - Rev. 00) PD-500-000 Function On vehicles fitted with air suspension, the Levelling Valve ensures that the axle suspension air bags maintain a
More informationSystem and Installation Instructions for KB4TA-G2
Systems for Commercial Vehicles Product Manual System and Installation Instructions for KB4TA-G2 24 Volt Multi-Channel Trailer-ABS With integrated anti-compounding Disclaimer The information contained
More informationINFORMATION DOCUMENT. Trailer Electronic Braking System Information Document ID_EB124_4E. Trailer EBS E Trailer EBS E with TCE
INFORMATION DOCUMENT Trailer Electronic Braking System Information Document ID_EB124_4E Trailer EBS E Trailer EBS E with TCE 2S/2M - 4S/3M APPR. LEV. COPYRIGHT DATE NAME COMPILER 15.01.2007 A. Stender
More informationVehicle Stability Function
Prepared by AMEVSC Secretary AMEVSC-03-04e Vehicle Stability Function Directional Control Roll-over Control A functional overview with regard to commercial vehicles 1 Definitions * Vehicle Stability Function
More informationOperating Instructions. for the WABCO Diagnostic Controller with Program Card ABS/ASR (ATC) D
Operating Instructions for the WABCO Diagnostic Controller with Program Card ABS/ASR (ATC) D 446 300 732 0 Operating Instructions for WABCO Diagnostic Controller 446 300 320 0 with Program Card ABS/ASR
More informationUser Manual. Compact Tester II st Edition
User Manual Compact Tester II 446 300 430 0 1st Edition This publication is not subject to any update service. You will find the new version in INFORM under www.wabco-auto.com Copyright WABCO 2006 Vehicle
More informationDATA PD LK..., LP... Product PD Air Compressors. Function. Technical Features
Commercial Vehicle Systems Product Doc. No. Y210611 DATA (EN - Rev. 000) Function The are piston-type and are used for generating compressed air to supply the air brake system, air suspension and auxiliary
More informationMaxxForce 11 and 13 (2010)
MaxxForce 11 and 13 (2010) Overview: In Cab Control NAV_PTOIC_070511 In-Cab Control TABLE OF CONTENTS General Overview: In-Cab Control... 1 Description and Operation... 1 OPERATION...1 STATIONARY VARIABLE...1
More informationREV F2.0. User's Manual. Hydraulic ABS (HABS) Hydraulic Power Brake (HPB) Page 1 of 28
REV F2.0 User's Manual Hydraulic ABS (HABS) Hydraulic Power Brake (HPB) Page 1 of 28 Table of Contents INTRODUCTION...4 Starting TOOLBOX Software... 5 MAIN MENU...6 System Setup... 6 Language... 7 Select
More informationKnorr-Bremse RailServices
Knorr-Bremse RailServices Energy efficiency in rolling stock through Knorr-Bremse refurbishments 8th June 2016 Alexander Schwan Desiro EcoTrain VT 642 modernization Development of an innovative technology
More informationPosition Paper. Anti-lock Braking for Agricultural Tractors
Position Paper Anti-lock Braking for Agricultural Tractors EUROPEAN ASSOCIATION OF AUTOMOTIVE SUPPLIERS CLEPA Prepared for the European Commission Expert Working Group Agricultural Tractors August 9 th,
More informationInternational A26 (2017)
International A26 (2017) Overview: Control - In Cab A26_ICESC_12292017 In-Cab Control TABLE OF CONTENTS General Overview: In-Cab Control... 1 Description and Operation... 1 OPERATION...1 STATIONARY VARIABLE...1
More informationActivation of a split shaft power take-off. Function
Function Function The function is intended to activate the power take-off from the driver area and from outside the cab. The power take-off is controlled by the BCI control unit. For the control of the
More informationDESCRIPTION. Chrysler NCV3 Service Info Section 08 > Electronic Modules > MODULE, Transmission Control Information
DESCRIPTION The transmission control module (TCM) receives, processes and sends various digital and analog signals related to the automatic transmission. In addition, it processes information received
More informationNewcastle Weighing Services Pty Ltd
Newcastle Weighing Services Pty Ltd Revision Sheet Revision 1 Marcus Graham Split Weighing in ClearWeigh This document describes the use of the split weighing facility in the ClearWeigh Touch Terminal
More informationActivation of EG power take-off. Function
Function Activation of EG power take-off The function is intended to activate the power take-off from the driver area and from outside the cab. The power take-off is controlled by the BCI control unit(bodywork
More informationDocument ID# Buick LeSabre
http://127.0.0.1:9001/servlets/blobshtml?shtmlfile=633088&evc=sm&pubid=262&cellid... Page 1 of 3 Document ID# 633088 DTC C1214 Circuit Description The system relay is energized when the ignition is ON.
More informationCEMA PT16 N09Rev2. Reference document: ENTR_F1_ _rev 16 v Article / clause Original text Proposal from CEMA Rationale and
CEMA PT16 N09Rev2 Reference document: ENTR_F1_030-99_rev 16 v030908 Article / clause Original text Proposal from CEMA Rationale and Art., clause 7 The fitment of anti-lock braking systems (ABS) is not
More informationPreparing and programming of ESGI 2 LPG supply system manual
Preparing and programming of ESGI 2 LPG supply system manual Part II Instruction of preparing and programming the ESGI system 1 Technical data of the central unit Vs Power supply voltage 0...16V V i_an
More informationVC-4820 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL
1. INTRODUCTION VC-4820 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL This MCU controlled Step Down DC-DC Converter has a digitally adjustable output in 0.2V increments. This
More informationDLRM DLRM
Table of Contents 1. Before You Begin.........................................................Page 1 2. Installation Tips..........................................................Page 2 3. Mounting Components
More informationthe systems people Owners Manual VCMS Switch Panel System Model VCMS-SP34
Owners Manual VCMS Switch Panel System Model VCMS-SP34 1. Product Description The Switch Panel System consists of a eight-position switch module, two six-output power modules and a 10 ft. communications
More informationINSTALLATION GUIDE. Electronic Braking System. Innovative Vehicle Solutions
INSTALLATION GUIDE Electronic Braking System Innovative Vehicle Solutions EB+ Gen3 Installation guide Notes on the use of this manual This manual has been designed to assist personnel in satisfactory installation
More informationGF42.47-P-0001FLM Adaptive brake (ABR), function
GF42.47-P-0001FLM Adaptive brake (ABR), function 14.1.13 MODEL 212 (except 212.095/098/298) as of model year 2014 Function requirements, general the engine is running or has been switched off by the ECO
More informationSubject: Power Take Off (PTO) Models Affected: ADVISORY:
Subject: Power Take Off (PTO) Subsystem Operating Description and Application Guide Models Affected: All New C/K 3500HD CC Chevrolet Silverado / GMC Sierra. Models C/K 36003, 36403 & 36043 Model Years:
More informationHIGHSPEED / COACHES LEADING IN ENTRANCE SYSTEMS FOR HIGHSPEED TRAINS AND PASSENGER COACHES
HIGHSPEED / COACHES 1 LEADING IN ENTRANCE SYSTEMS FOR HIGHSPEED TRAINS AND PASSENGER COACHES 2 PROVEN AND RELIABLE: ENTRANCE SYSTEMS UP TO 80 KM/H HIGHSPEED TRAINS AND PASSENGER COACHES SYSTEMS FOR RAIL
More information»Plug&Play«Paddle Shift System Kit - Porsche 997 GT3 Cup
»Plug&Play«Paddle Shift System Kit - Porsche 997 GT3 Cup FUNCTIONAL DESCRIPTION AGENDA 1. Introduction 2. System overview 2.1 Central Unit (GCU) 2.2 Valve block 3V 2.3 Shift cylinder 2.4 Blip cylinder
More informationVALVE BODY. Shift Pressure Control Solenoid Valve. 1. Leaf spring 2. Contact spring 3. Conductor track 4. O-ring 5. O-ring 6.
72 3650 VALVE BODY Shift Pressure Control Solenoid Valve 8 9 7 7 A B C D 10 7 E F 1. Leaf spring 2. Contact spring 3. Conductor track 4. O-ring 5. O-ring 6. Shift plate 7. Leaf spring and socket bolt 8.
More informationPCS GEAR SELECT MODULE USER GUIDE v4.0
PCS GEAR SELECT MODULE USER GUIDE v4.0 Ph: 1.804.227.3023 www.powertraincontrolsolutions.com Powertrain Control Solutions 1 Introduction 1.1 Included Components 1 - GSM Cable Motor Enclosur 1 - GSM Driver
More informationLED Diagnostic Display. ABS Modulator. Connector (MOD1) Supply Port 1/2" NPT MC-30 CONTROLLER INTRODUCTION
SD-13-4834 Bendix MC-30 Trailer ABS Controller Assembly LED Diagnostic Display 30-Pin Connector ABS Modulator Connector (MOD1) Control Port 1/4" NPT Delivery Ports 3/8" NPT (x4) TABLE OF CONTENTS PAGE
More informationShift Solenoid "A" Performance (Shift Solenoid Valve S1)
78 DTC P0751 Shift Solenoid "A" Performance (Shift Solenoid Valve S1) DESCRIPTION The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st,
More informationBreaker failure protection function block description
function block description Document ID: PRELIMINARY VERSION User s manual version information Version Date Modification Compiled by Preliminary 24.11.2009. Preliminary version, without technical information
More informationEBS IN TOWING VEHICLES AND BUSES SYSTEM DESCRIPTION
EBS IN TOWING VEHICLES AND BUSES SYSTEM DESCRIPTION EBS in towing vehicles and buses System Description 3rd edition This publication is not subject to an updating service. New versions can be found in
More informationInstallation Instructions Vario Compact ABS (VCS)
Installation Instructions Vario Compact ABS (VCS) 1 Installation Instructions Vario Compact ABS (VCS) Installation of the Vario Compact ABS developed by WABCO is very easy and requires very little effort.
More informationSetting the Standards Trailer Component Suppliers Perspective
Setting the Standards Trailer Component Suppliers Perspective Mario Colosimo BPW Historical Perspective For many years trailers had to be cheap to buy, with little consideration to whole of life costs.
More informationInformation I Manuals I service. AIR premium x2. Operating Instructions _a I 03/2012
GB Information I Manuals I service AIR premium x2 Operating Instructions 1 568 419_a I 03/2012 1 6 7 2 3 4 8 5 Dear customer, Your vehicle is equipped with the AL KO AIR Premium X2 electronically controlled
More informationVehicle makes models and variants known or believed to be using this vehicle system, required diagnostic lead and degree of known compatibility.
HELLA CRUISE CONTROL - System Overview This is a tiny ECU which is surprisingly versatile and turns up in lots of different places. Sometimes it co exists with an engine management specific interface ECU
More informationTechnical Report. No. EB138.0 on a measurement and simulation device to check compliance with the provisions of the ECE Regulation No.
Technical Report No. EB138.0 on a measurement and simulation device to check compliance with the provisions of the ECE Regulation No. 13 This Technical Report serves as a verification of the conformity
More informationProposed amendment to ECE Regulation 13
ACV-06-10 Rev1 Outcome of the ACV working group meeting 6 based on document ACV-06-02 Proposed amendment to ECE Regulation 13 The text reproduced below was prepared by the experts of the informal working
More informationParameters Powertrain
Introduction Introduction Note: The parameters that are available in a specific vehicle depend on the vehicle configuration. This document describes parameters that are associated with the powertrain.
More informationAdditions, Revisions, or Updates
1 4 09-14 SUBJECT DATE ACM2.1 SPN 3597/FMI 3, 4 - GHG14 April 2014 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN 3597/FMI 3,
More informationRIDE AND HANDLING OPTIMIZATION
PUBLISHED: 26-JAN-2015 2013.0 RANGE ROVER SPORT (LS), 204-06 RIDE AND HANDLING OPTIMIZATION DESCRIPTION AND OPERATION Terrain Response - Component Location ITEM DESCRIPTION 1 Terrain Response control and
More informationEconomic and Social Council
UNITED NATIONS Economic and Social Council Distr. GENERAL TRANS/WP.29/78/Rev.1/Amend.2 16 April 1999 ENGLISH Original: ENGLISH and FRENCH ECONOMIC COMMISSION FOR EUROPE INLAND TRANSPORT COMMITTEE Working
More information6-speed automatic transmission E60, E53. VS-22 je Baugruppe/Group: (040) 09/2003. Introduction
VS-22 je Baugruppe/Group: 24 24 01 03 (040) 6-speed automatic transmission E60, E53 weltweit Datum/Date: 09/2003 Introduction The 6-speed automatic transmissions GA6HP19Z and GA6HP26Z have been jointly
More information2001 Chevrolet Corvette ACCESSORIES & EQUIPMENT Remote Keyless Entry Systems - Corvette
DESCRIPTION 2001 ACCESSORIES & EQUIPMENT Remote Keyless Entry Systems - Corvette Remote Keyless Entry (RKE) system is controlled by Remote Function Actuation (RFA) system. Transmitter allows remote control
More informationShift Solenoid "B" Performance (Shift Solenoid Valve S2)
86 A750E AUTOMIC TRANSMISSION AUTOMIC TRANSMISSION SYSTEM DTC P0756 Shift Solenoid "B" Performance (Shift Solenoid Valve S2) DESCRIPTION The ECM uses signals from the output shaft speed sensor and input
More informationSection 55 Chapter 6
Section 55 Chapter 6 REMOTE HYDRAULICS CONTROLLER Calibration and Fault Codes 6-12880NH TABLE OF CONTENTS REMOTE HYDRAULICS CONTROLLER CALIBRATION... 55-5 Requirements For Calibration... 55-5 Aux Set Main
More informationCS 430RC. Solid De-icer Controller Configuration and Set-up Manual
CS 430RC Solid De-icer Controller Configuration and Set-up Manual 2/17 Table of Contents 1 Systems Modes of Operation 3 2 System Features 4 3 System Description 5 4 System Specifications 6 4.1 CS-430RC
More informationEB : e-stroke GEN 3 USERS GUIDE for Bus Applications
EB 09-005: e-stroke GEN 3 USERS GUIDE for Bus Applications SECTION 1: INTRODUCTION The purpose of the e-stroke Brake Monitoring System is to enhance the operational safety of commercial vehicles. The e-stroke
More informationE61, E63, E64 BMW AG - TIS
VS-22 es Baugruppe/Group: 66 meeknet.co.uk/e64 Park Distance Control E60, E61, E63, E64 66 01 03 (051) weltweit Datum/Date: 06/2003 Update: 07/2004 Introduction Park Distance Control (PDC) is an item of
More informationProduct Specification
Product Specification Function, quality and reliability are subjects of this specification. If the Vario Compact Anti-Lock System is operated under conditions that are not described in this specification,
More informationTechnical Report. No. KO250.3E. on the TRAILER CONTROL MODULE
Technical Report No. KO250.3E on the TRAILER CONTROL MODULE Mobilität TÜV NORD Mobilität GmbH & Co. KG IFM Institute for Vehicle Technology and Mobility Adlerstraße 7 45307 Essen Tel.: +49 (0)201 825-4120
More informationSD Bendix MV-3 Dash Control Module DESCRIPTION. Bottom View
SD-03-3415 Bendix MV-3 Dash Control Module MOUNTING PLATE MOUNTING HOLES (4) Dual Circuit SUPPLY Check VALVE AUXILIARY PORT (Optional) delivery DESCRIPTION secondary supply Trailer delivery FIGURE 1 -
More informationCS 420RC. Solid De-icer Controller Configuration and Set-up Manual
CS 420RC Solid De-icer Controller Configuration and Set-up Manual 2/15 Table of Contents 1 Systems Modes of Operation 3 2 System Features 4 3 System Description 5 4 System Specifications 6 4.1 CS-420RC
More informationBattery, Mounting and Cables - Battery and Cables Description and Operation
Battery, Mounting and Cables - Battery and Cables Description and Operation COMPONENT LOCATION - SINGLE BATTERY VEHICLES Item 1 2 3 4 5 6 7 8 9 10 Description Jump start terminal negative (-) Jump start
More informationThe parking brake is an electrically actuated system that operates drum brakes integrated into the rear brake discs. The
Page 1 of 15 Published: Oct 22, 2004 Parking Brake COMPONENT LOCATIONS Item Part Number Description 1 Clutch pedal position sensor (manual transmission models only) 2 Parking brake indicators (all except
More informationInstruction of connection and programming of the VECTOR controller
Instruction of connection and programming of the VECTOR controller 1. Connection of wiring 1.1.VECTOR Connection diagram Fig. 1 VECTOR Diagram of connection to the vehicle wiring. 1.2.Connection of wiring
More informationPressing and holding the + RES switch, when the Cruise Control System is engaged, will allow the vehicle to
CRUISE CONTROL DESCRIPTION AN... CRUISE CONTROL DESCRIPTION AND OPERATION (CRUISE CONTROL) Document ID# 2088041 Cruise Control Description and Operation Cruise control is a speed control system that maintains
More informationCEMA position on draft braking regulation, 4 June 2008 ENTR/F1/ /rev16
CEMA PT16 N05Rev CEMA position on draft braking regulation, 4 June 2008 ENTR/F1/5030-99/rev16 CEMA is the European association representing the agricultural machinery industry. It represents the industry
More informationIgnition Power Management
This chapter provides a description and instructions for configuration of the feature of the IR829 router. It also keeps the IR829 up and running while the vehicle is stopped. Therefore, users do not have
More informationSenior Swing Control Box. Table of Contents
*740100* 740100 2800 Overhead Consealed Series 9500 Surface Applied Series Senior Swing Control Box Installation Instructions important These instructions are presented in step-by-step sequence. It is
More informationAdditions, Revisions, or Updates
01 04-15 1 01 04-15 SUBJECT DATE SPN 3464/ FMI 16, 18 (MCM) (GHG14) January 2015 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0084 DD Platform SPN
More informationVC-30 / VC-40 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL
1. INTRODUCTION VC-30 / VC-40 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL This MCU controlled Step Down 24V to 12V DC-DC Converter has a programmable 12.0 to 15.0V output in
More informationShift Solenoid "B" Performance (Shift Solenoid Valve S2)
88 A750F AUTOMIC TRANSMISSION AUTOMIC TRANSMISSION SYSTEM DTC P0756 Shift Solenoid "B" Performance (Shift Solenoid Valve S2) DESCRIPTION The ECM uses signals from the output shaft speed sensor and input
More informationFOUR-WHEEL ANTI-LOCK BRAKE SYSTEM (4ABS)
35B-1 GROUP 35B FOUR-WHEEL ANTI-LOCK BRAKE SYSTEM (4ABS) CONTENTS GENERAL INFORMATION 35B-2 35B-6 SENSOR 35B-6 ACTUATORS 35B-6 ABS-ECU 35B-7 35B-2 The ABS that ensures directional stability and controllability
More informationVehicle Standard (Australian Design Rule 35/06 Commercial Vehicle Brake Systems) 2018
DRAFT Australian Design Rule 35/06 Commercial Vehicle Brake Systems 1 Vehicle Standard (Australian Design Rule 35/06 Commercial Vehicle Brake Systems) 2018 I, PAUL FLETCHER, Minister for Urban Infrastructure,
More informationProgrammable 8 Channel Injector Driver Module
Overview: Programmable 8 Channel Injector Driver Module 554-142 The 8 channel fuel injector driver module allows for an input signal from any ECU to be changed into a user selectable peak and hold current.
More information5 FEATURES DDEC FOR MBE900 AND MBE4000
DDEC FOR MBE900 AND MBE4000 5 FEATURES Section Page 5.1 ANTI-LOCK BRAKE/AUTOMATIC TRACTION CONTROL SYSTEMS.. 5-5 5.2 COLD START... 5-7 5.3 CRUISE CONTROL... 5-11 5.4 DIAGNOSTICS... 5-19 5.5 DUAL SPEED
More informationTWO-WAY LED AUTOMATIC TRANSMISSION REMOTE STARTER. User Guide WARNING
TWO-WAY LED AUTOMATIC TRANSMISSION REMOTE STARTER User Guide WARNING It is the responsibility of the vehicle operator to ensure their vehicle is parked in a safe and responsible manner. 1. When leaving
More informationMaxxForce 7 (2010) PTO Remote Engine Speed Control Navistar, Inc.
MaxxForce 7 (2010) Overview: Remote Engine Speed Control NAV_R _041111 TABLE OF CONTENTS General Overview: Remote Engine Speed Control... 1 Description and Operation... 1 OPERATION...1 FEATURE INTERACTION...2
More informationSIDE ROLL SENSOR TROUBLESHOOTING GUIDE
SIDE ROLL SENSOR TROUBLESHOOTING GUIDE WARNING Service the roll sensor(s) only if you are an authorized technician. The roll sensor triggers airbags and seat restraints. Accidental deployment could cause
More information