DATA PD-214-F104. TEBS G2 Doc. No. Y (EN - Rev. 001) May Product. icargo. Function. Operation
|
|
- Mervin Wheeler
- 5 years ago
- Views:
Transcription
1 Commercial Vehicle Systems Product DATA Function On semi-trailers and centre-axle trailers, the axle/bogie will act as a pivot point that, depending on the positioning of the cargo carried by the trailer, will influence the loading of the towing vehicle. In many multi-drop operations, if the cargo is badly positioned or if some cargo is off-loaded without consideration for the distribution of the remaining cargo, this can result in overloading of the towing vehicle s drive axle(s). is a function within Knorr-Bremse s TEBS G.0/G./G. braking systems (with the Trailer Brake Module (TBM) having the relevant software version) which interfaces with the trailer s air suspension system and adjusts the pressure in the air bags of an axle to move the effective bogie centre line and attempt to bring the load on the driving axle of the towing vehicle down to the legal maximum. A further benefit of is reduction in tyre wear. TEBS G Doc. No. Y (EN - Rev. 00) May 0 Doc. No. Y (EN - Rev. 00) May 0 kg PD--F0 Operation is a function of the TEBS G.0/G./G. braking systems which interfaces with the trailer s air suspension system and adjusts the pressure in the air bags of an axle to adjust the load carried by that axle. TEBS G.0/G. with also controls the brakes on that axle separately. The system requires the braking system to be a S/M system and so it is only suitable for TEBS G. systems with TEBS G. Premium Brake Modules. Example: -axle semi-trailer with controlling axle The suspension pressure in the air bags of axles and is measured by the pressure transducer in port of the TBM while the pressure in the air bags on axle is measured by the transducer in port of the Trailer Electro-Pneumatic Module - Premium (TEPM-P). The signal for the transducer in the TEPM-P is then fed to the TBM. constantly monitors the bogie load carried by axles and as a percentage of the total bogie load. Axle loading Axle loading Over If the cargo distribution has resulted in load being removed behind (without loaded ) the trailer bogie, when recognises that there is a risk of overloading the tractor s drive axle because of the cargo forward of the trailer s bogie, will reduce the pressure in the air bag on axle using the Pressure Control Valve (PCV). This will result in more load being carried by axles and, and less being imposed on the king pin and consequently the tractor s drive axle. will ensure that the non-controlled axles of the trailer will be laden up to its programmed maximum (see page ). The default setting Axle loading (with ) is 00%. If this load figure has been reduced during Set Up then will adjust the load accordingly. Air bag pressure reduced Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
2 PD--F0 TEBS G Product Data Doc. No. Y (EN - Rev. 00) May 0 Example: -axle centre-axle trailer with controlling axle The suspension pressure in the air bags of axle is measured by the pressure transducer in port of the TBM, while the pressure in the air bags on axle is measured by the transducer in port of the TEPM-P. constantly monitors the load carried by axle as a percentage of total bogie load. If the cargo distribution has resulted in load being removed behind the trailer bogie, when calculates that there is a risk of overloading the towing vehicle s drive axle because of the cargo forward of the trailer s bogie, will operate as in the semi-trailer example above. (without ) Over loaded Example: -axle centre-axle trailer with controlling axle On a centre-axle trailer which carries a fork lift truck on the rear of the trailer to assist in unloading, when the trailer is unladen the presence of the fork lift truck will reduce the load on the trailer coupling which could lead to instability of the trailer. In this situation would be installed on axle to move the fulcrum point towards the rear and counter the effect of the fork lift truck. (with ) Stable Air bag pressure reduced The activation of results in the reduction of load imposed on the axle it controls and this will increase the risk of wheel locking during braking. For this reason the service braking of this controlled axle is always supplied through the TEPM-P thus enabling independent ABS control of the axle controlled by. In general is deactivated when the bogie load falls below Disable setting (see Set Up). Below this load the trailer (without ) (with ) is lightly loaded and there is no need for its function. is not re-activated until the bogie load exceeds the Enable setting (see Set Up). Unstable Stable Air bag pressure reduced Note: within the air bags of the controlled axle have a configurable minimum pressure below which the pressure is not reduced. This prevents bouncing of the axle which may cause damage to the trailer or the road. during operation, any lift axle forward of the fixed axle, or forward of the axle controlled by will be lowered automatically, as keeping it raised would have a negative effect on s performance. when is not active ( Disabled), the axle(s) controlled by is treated as a normal lift axle under the control of the automatic lift axle control logic. can be disabled in several ways: disable switch connected to any AUXIO pin. Traction Help (TH) request from the towing vehicle activation of the Automatic Traction Control (ATC) function on the towing vehicle. bogie load falls below the setting of Disable (see Set Up). The priority of relative to other functions is shown below: Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
3 Commercial Vehicle Systems Doc. No. Y (EN - Rev. 00) May 0 TEBS G PD--F0 Priority Function Description Highest Auxiliary Design Language (ADL) Lowest Activation of a function will override any action requested by a function with a lower priority ISO 99 or J99 CAN commands Driver request ISO 99 CAN ATC status icorner Automatic Lift Axle Control (LAC) An ADL program may override any calculated lift axle state. A command such as Raise or Lower a lift axle will disable all lower priority functions. Driver request via a connected manual switch input such as Traction Help. ATC Active will cause an automatic Traction Help request. An icorner command will override any or Automatic Lift Axle Control command. An command will override any Automatic Lift Axle Control command. If no other request is active then the Automatic Lift Axle Control will take control of the lift axle(s). Set Up TEBS G.0/G. TEBS G. Premium Setting up of is carried out using the Knorr Bremse diagnostic software. ECUtalk (version...0 or higher is required). This can be downloaded from BremseCVS.com in the Download Software section. Note: example shown here is a -axle semi-trailer. Use ECUtalk, select Information then Change Configuration to configure the system. Click Next. Select the axle to be controlled by. Note: on semi-trailers the axle is the rearmost by default, on centre-axle trailers the axle controlled by can be either behind or in front of the non-lifting axle. Click on Next. Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
4 PD--F0 TEBS G Product Data Doc. No. Y (EN - Rev. 00) May 0 Set the required control parameters. can be automatically disabled below a given axle/bogie load ( Disable ) and re-enabled above a higher axle/bogie load ( Enable ). Once is disabled below the set axle/bogie load, the controlled axle will have only a minimum pressure maintained in its air bags - the default pressure is 0. bar but this can be adjusted. This pressure is the minimum that will be retained in the air bags during any and lift axle control operation. Retaining a minimum pressure prevents the axle being damaged due to oscillation or bouncing on poor road services and mimics use of a pressure retention valve fitted in conventional suspension control circuits. The Load [%] setting controls the degree of load that can be experienced on the other (noncontrolled) axle(s). The default is set to 00% but it is also be possible to program different values (from 90% upwards). TEBS G.0/G. TEBS G. Premium Click on when all of the required parameters are set. is now ready for operation. Note: Ensure that the recommendations of the axle manufacturer are observed with regard to overload. Note: It is the vehicle manufacturer s responsibility to ensure that the air suspension system is capable of supplying sufficient air pressure and volume to the air bags of the axles not raised or off-loaded during operation to ensure that the required axle load is carried by those axles. Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
5 Commercial Vehicle Systems Doc. No. Y (EN - Rev. 00) May 0 TEBS G PD--F0 System Requirements requires the following components: Part No. Type No. Description In the range K0900 to K0909* or K090 to K099* ES00 TEBS G.0 or TEBS G. Brake Module (TBM) [Software version 00. or higher] OR K0* ES09 TEBS G. Premium Brake Module (TBM) K0900 ES0 Trailer Electro-Pneumatic Module Premium (TEPM-P) [Software version 00. or higher] K088 - Pressure Control Valve (PCV) K00, K008, K009* - PCV Connecting Cables (, 9, m) See PD--0, Document No. Y8 for suitable cables TEPM-P Connecting Cables * alternatives depending on vehicle design specification may be fitted on trailers with lift axle control (LAC) (see PD--F0, Document No. Y8) and icorner (see PD--F0, Document No. Y). Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
6 PD--F0 TEBS G Product Data Doc. No. Y (EN - Rev. 00) May 0 Installation - typical installation TEBS G.0 or G. Brake Module (TBM) Trailer Electro-Pneumatic Module Premium (TEPM-P) Pressure Control Valve (PCV) Levelling Valve 00bw is a function of the TEBS G.0/G./G. braking systems and requires the fitment of a suitable TEBS G.0, G. or G. Premium Brake Module (TBM) plus a Trailer Electro-Pneumatic Module Premium (TEPM-P) and a Pressure Control Valve (PCV) - see System Requirements on page. The TEPM-P is used to control the service braking on the axle to be controlled by and the PCV controls the air pressure in the air suspension on that axle. All other equipment is as would be installed on a standard TEBS G.0/G./G. system. Note: Knorr-Bremse recommends a minimum air suspension reservoir capacity of 0 litres for. During operation the pressure in the air bags of the controlled axle will be reduced and so the system must provide separate anti-lock (ABS) control of the service brakes on that axle. This is achieved by having a S/M system with the TEPM-P acting as the third modulator. The TBM should be installed as specified in the PD--00, Document No. Y00. The PCV should be installed centrally above the controlled axle, ideally with the supply to the air bags coming from a T-piece at the PCV. The air suspension connection to port of the TEPM-P must come from the air bag on that axle which is further from the PCV. The TEPM-P and PCV are connected to the In-Out Connector of the TEBS G.0/G./G. Premium Brake Module. A disable switch should be fitted to allow the driver to disable the function. Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
7 Commercial Vehicle Systems Doc. No. Y (EN - Rev. 00) May 0 TEBS G PD--F0 Typical Wiring Diagram - TEBS G. with output ISO 8 Trailer Electro-pneumatic Module Premium (TEPM-P) S-A X S-B 8 RD BK YE BN WH WH/GN WH/BN Pressure Control Valve (PCV) (YE) (BK) (WH) (BN)... (BK) (WH) (YE) (YE) (BK) (WH) (BN) RD BK YE BN WH WH/GN WH/BN YE BK YE WH BN WH BK V_VALVE V_ECU GND_H GND_M WL V-CAN-H V-CAN-L AUX IO AUX IO AUX IO SENS_Sup / TriState SENS_In / TriState SENS_GND Brake-Light V Brake-Light GND V-CAN-L V-CAN-H AUX IO - RET AUX IO - RET S-D In-Out S-F S-C S-E Power B TEBS G. - ECU _00 This document forms part of the Product Manual for the TEBS G Family, Document No. Y0 Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
8 PD--F0 TEBS G Product Data Doc. No. Y (EN - Rev. 00) May 0 Revision Details Rev. 000 September 0 New document Rev. 000 August 0 Correction changed to in line with other language versions Rev. 00 May 0 TEBS G. Premium added. Pressure Control Valve K008 replaced by K088. Knorr-Bremse Systeme für Nutzfahrzeuge GmbH. Moosacher Straße Munich. Germany. Tel: Fax:
DATA. icargo) Product. Application. Purpose. Function. Knorr-Bremse s intelligent axle loading system, icargo, is designed to work on:
Commercial Vehicle Systems Product DATA Doc. No. Y09 (EN - Rev. 00) January 0 Application Knorr-Bremse s intelligent axle loading system,, is designed to work on: Semi-trailers with two to five axles Centre-axle
More informationLift axle control on axle 1. Lift axle control on axle 3
Commercial Vehicle Systems Product DATA Function On vehicle combinations using semi-trailers it is often difficult to meet the turning corridor required by European Community (EC) legislation. When certain
More informationDATA PD-214-F101. TEBS G2 Doc. No. Y (EN - Rev. 001) July Product. Lift Axle Control. Function. Operation
Commercial Vehicle Systems Product DATA Function Many trailers have one or more axles having the capability of being lifted so that they carry none of the trailer load. The function is present in the TEBS
More informationDATA PD AE1141 Lift Axle Valves - TEBS controlled. P r o d u c t
C o m m e r c i a l V e h i c l e S y s t e m s P r o d u c t DATA AE Doc. No. Y05067 (Rev. 00) August 0 PD-50-00 Function The TEBS controlled Lift Axle AE Valve is used for trailers with electronic braking
More information1. Semi- and centre-axle trailers To enable the automatic load sensing function to operate, it is necessary to define certain parameters as follows:
Commercial Vehicle Systems Product DATA Function Load Sensing Function (pneumatic suspension) PD-4-F00 The Load Sensing Function (LSF) of the TEBS Brake Module is used to replace the function of a load
More informationDriving Position. Raise/Lower Position. Adaptor Plate* 19 min
Commercial Vehicle Systems Product DATA Raise/Lower Valves (single circuit) Doc. No. Y0377 (EN - Rev. 003) October 0 PD-501-050 Function Raise/Lower Valves are fitted on vehicles with air suspension and
More informationWeight Stroke TÜV-Inspection approx. [kg] II )4) BZ M16x Port threads:
Commercial Vehicle Systems Product DATA Spring Brakes (S-cam), diaphragm/piston Doc. No. Y1137 (EN - Rev. 5) September 216 PD-413-1 Function This range of Spring Brakes is used on axles fitted with drum
More informationDATA PD BR43.. Load Sensing Valve - mechanically controlled. Product. Function. Technical Features. Range Overview
Commercial Vehicle Systems Product DATA BR.. Doc. No. Y0 (EN - Rev. 00) May 0 PD-0-000 Function The Load Sensing Valve is used to adjust the applied service brake pressure in relation to the load imposed
More information. For 4S/3M applications an Integrated Speed Switch (ISS)
Commercial Vehicle Systems Product DATA PD-203-430 Function The Knorr-Bremse KB4TA module is an integrated ABS electronic control unit and dual modulator valve for air braked trailers (semi-trailers, centre-axle
More informationTrailer brake and chassis control
COMMERCIAL VEHICLE SYSTEMS BRAKE AND CHASSIS CONTROL Trailer brake and chassis control TRAILER COMPETENCE 2 THE MUNICH-BASED KNORR-BREMSE GROUP IS THE WORLD S LEADING MANUFACTURER OF BRAKING SYSTEMS FOR
More informationDATA PD ES1305. Product. Trailer ABS (KB4TA) Function
V Commercial Vehicle Systems Product DATA PD-203-300 Function The Knorr-Bremse KB4TA module is an integrated ABS electronic control unit and dual modulator valve for air braked trailers with mechanical
More informationDATA PD LS1..., LS2..., LS3... Lift Axle Valves - Pneumatic. P r o d u c t. Function. Technical Features
C o m m e r c i a l V e h i c l e S y s t e m s P r o d u c t DATA PD-503-200 Function Pneumatic Lift Axle Control Valves are used for the semi-automatic or fully automatic control of air suspended lift
More informationDATA PD VB... Air Reservoirs. Product. Function. Technical Features. Range Overview - mounting straps for steel and aluminium reservoirs
Commercial Vehicle Systems Product DATA Doc. No. Y095687 (EN Rev. 004) February 16 PD50 Function are used to store the compressed air for the vehicle air braking, suspension and auxiliary systems. They
More informationFeatures: ECUtalk enables the user to:
Features: ECUtalk enables the user to: Retrieve information from the ECU: - General - Error status - Configuration Change the ECU s configuration Check System components Carry out EOL tests Generate Load
More informationKnorr-Bremse Commercial Vehicle Systems. Training program, second half of 2017, Poland
Knorr-Bremse Commercial Vehicle Systems Training program, second half of 2017, Poland Information Trainings are conducted at Knorr-Bremse TruckeServices training center, Piaskowa 4/2 St., Warsaw Maximum
More informationTrailer EBS E Trailer EBS E with TCE
. Date Copyright WABCO Signature Information Document Compiled Trailer EBS E 2008-05-20 Barlsen 2008-05-20 Stender Stender Checked Expert ECN No. Revision Date of first issue Product Group Product Identification
More informationFunction ECU, Wireless
Commercial Vehicle Systems Product DATA PD-551-000 Function ECU, Wireless The is a Gateway Receiver system to alert the driver if any monitored tyre runs under its normal pressure or above its normal temperature.
More informationEBS and More. What can you do with advanced braking systems? Chair : Mario Colosimo. Robert Smedley, Knorr Bremse Ian Thomson, BPW Transpec
EBS and More What can you do with advanced braking systems? Chair : Mario Colosimo Panel : Neil Chilton, Warnambool Cheese and Butter Robert Smedley, Knorr Bremse Ian Thomson, BPW Transpec Trailer Electronic
More informationFunction ECU, Wireless
Commercial Vehicle Systems Product DATA PD-551-000 Function ECU, Wireless The is a Gateway Receiver system to alert the driver if any monitored tyre runs under its normal pressure or above its normal temperature.
More informationDATA PD LK..., LP... Product PD Air Compressors. Function. Technical Features
Commercial Vehicle Systems Product Doc. No. Y210611 DATA (EN - Rev. 000) Function The are piston-type and are used for generating compressed air to supply the air brake system, air suspension and auxiliary
More informationFriction Material. Freight Cars High-Speed Trains Light Rail Vehicles Locomotives Metros Passenger Coaches Regional and Commuter Trains
Friction Material Applications Freight Cars High-Speed Trains Light Rail Vehicles Locomotives Metros Passenger Coaches Regional and Commuter Trains 2 KNORR-BREMSE A FULL LINER IN FRICTION MATERIAL Our
More informationKnorr-Bremse RailServices
Knorr-Bremse RailServices Energy efficiency in rolling stock through Knorr-Bremse refurbishments 8th June 2016 Alexander Schwan Desiro EcoTrain VT 642 modernization Development of an innovative technology
More informationHydraulic Fluid: Master Cylinder dia. [mm]
Commercial Vehicle Systems Product DATA Function This range of Brake Chambers with Master Cylinder is used to apply the service brakes on axles fitted with hydraulic brakes. The chamber applies force to
More informationSD Bendix TABS 6 Advanced Single-Channel Trailer ABS Module 1. INTRODUCTION
SD-13-47671 Bendix TABS 6 Advanced Single-Channel Trailer ABS Module ECU Cover (Sealed) Through-holes for Frame (Chassis) Mounting ECU Part Number Label (See Page 34) 18-Pin Connector 3/8" NPT Load Port
More informationSd Bendix TABS 6 Advanced Multi Channel Trailer ABS Module. 1. InTRodUCTIon
Sd 3 4767 TABS 6 Advanced Multi Channel Trailer ABS Module Mounting Studs -Pin ECU Cover (Sealed) ECU Covers on Both Sides (Removable) 7-Pin Mounting Studs Wheel Speed Sensor s For Port Descriptions See
More informationPosition Paper. Anti-lock Braking for Agricultural Tractors
Position Paper Anti-lock Braking for Agricultural Tractors EUROPEAN ASSOCIATION OF AUTOMOTIVE SUPPLIERS CLEPA Prepared for the European Commission Expert Working Group Agricultural Tractors August 9 th,
More informationINSTALLATION GUIDE. Electronic Braking System. Innovative Vehicle Solutions
INSTALLATION GUIDE Electronic Braking System Innovative Vehicle Solutions EB+ Gen3 Installation guide Notes on the use of this manual This manual has been designed to assist personnel in satisfactory installation
More informationREV F2.0. User's Manual. Hydraulic ABS (HABS) Hydraulic Power Brake (HPB) Page 1 of 28
REV F2.0 User's Manual Hydraulic ABS (HABS) Hydraulic Power Brake (HPB) Page 1 of 28 Table of Contents INTRODUCTION...4 Starting TOOLBOX Software... 5 MAIN MENU...6 System Setup... 6 Language... 7 Select
More informationOperator's Guide ELECTRONIC BRAKE SYSTEMS DIAG+
Operator's Guide ELECTRONIC BRAKE SYSTEMS DIAG+ www.haldex.com Content Contents Introduction Minimum System Specification Page 2 Installation Options Page 3 ECU Connnections Page 4 Secondary Displays Page
More informationDATA PD AE431. Product. Park/Shunt Valves with Integrated Emergency Function. Function
Commercial Vehicle Systems Product DATA Park/Shunt Valves with Integrated Emergency Function PD-113-0 Function The Park/Shunt Valve is used on trailers that are equipped with spring brakes. It is connected
More informationProposed amendment to ECE Regulation 13
ACV-06-10 Rev1 Outcome of the ACV working group meeting 6 based on document ACV-06-02 Proposed amendment to ECE Regulation 13 The text reproduced below was prepared by the experts of the informal working
More informationSystem and Installation Instructions for KB4TA-G2
Systems for Commercial Vehicles Product Manual System and Installation Instructions for KB4TA-G2 24 Volt Multi-Channel Trailer-ABS With integrated anti-compounding Disclaimer The information contained
More informationTRS - Trailer Roll Stability
TRS - Trailer Roll Stability Todd Bourque Canadian OEM Sales Manager Braking Controls Division Haldex Brake Products, Inc. Innovative Vehicle Technology Innovative Vehicle Technology 2 1 Innovative Vehicle
More informationProduct Specification
Product Specification Function, quality and reliability are subjects of this specification. If the Vario Compact Anti-Lock System is operated under conditions that are not described in this specification,
More informationParameters Chassis. Introduction
Introduction To limit the list of parameters in this document, only parameters considered to be of use to bodybuilders are described. For full details of the current parameters for a specific vehicle,
More informationBombardier Crewe. West Street Crewe, Cheshire United Kingdom CW1 3JB. has been assessed and approved
, Cheshire has been assessed and approved in accordance with the requirements of RISAS/003 for 34 product groups, of which 9 have limitations. The scope of accreditation is applicable only to the products
More informationInstructions for the Vertical and Lateral Alignment of Bendix Radar Sensors
Instructions for the Vertical and Lateral Alignment of Bendix Radar Sensors This is an extract from the Bendix Service Data Sheet SD-13-4962 Bendix Wingman Advanced. To download the full document, visit
More informationInstallation Instructions
Installation Instructions Recall Campaign No. 16E045 FIELD REPAIR KIT FOR THE BENDIX SR-5 TRAILER SPRING BRAKE VALVE Spring Retainer Reservoir Fitting 1/4" P.T. Service/Spring Brake Reservoir (2) SR-5
More informationINFORMATION DOCUMENT. Trailer Electronic Braking System Information Document ID_EB124_4E. Trailer EBS E Trailer EBS E with TCE
INFORMATION DOCUMENT Trailer Electronic Braking System Information Document ID_EB124_4E Trailer EBS E Trailer EBS E with TCE 2S/2M - 4S/3M APPR. LEV. COPYRIGHT DATE NAME COMPILER 15.01.2007 A. Stender
More informationOperating Instructions. for the WABCO Diagnostic Controller with Program Card ABS/ASR (ATC) D
Operating Instructions for the WABCO Diagnostic Controller with Program Card ABS/ASR (ATC) D 446 300 732 0 Operating Instructions for WABCO Diagnostic Controller 446 300 320 0 with Program Card ABS/ASR
More informationBendix ACom Diagnostic Software Starter Guide. Steps for proper installation and operation
Bendix ACom Diagnostic Software Starter Guide Steps for proper installation and operation 1 GENERAL SAFETY GUIDELINES WARNING! PLEASE READ AND FOLLOW THESE INSTRUCTIONS TO AVOID PERSONAL INJURY OR DEATH:
More informationSpecial Vehicles. rail vehicle systems REALIZING SYSTEM SYNERGIES
Special Vehicles rail vehicle systems Special Vehicles 1 REALIZING SYSTEM SYNERGIES Windscreen Wiper Air Conditioning Router Air Dryer Brake Controller Controller 2 Sanding Brake Control Switch As rail
More informationEBS IN TOWING VEHICLES AND BUSES SYSTEM DESCRIPTION
EBS IN TOWING VEHICLES AND BUSES SYSTEM DESCRIPTION EBS in towing vehicles and buses System Description 3rd edition This publication is not subject to an updating service. New versions can be found in
More informationDATA PD SV13.., SV14.. Levelling Valves. Product. Function. Technical Features. Range Overview
Commercial Vehicle Systems Product DATA Doc. No. Y075 (EN - Rev. 00) PD-500-000 Function On vehicles fitted with air suspension, the Levelling Valve ensures that the axle suspension air bags maintain a
More informationSetting the Standards Trailer Component Suppliers Perspective
Setting the Standards Trailer Component Suppliers Perspective Mario Colosimo BPW Historical Perspective For many years trailers had to be cheap to buy, with little consideration to whole of life costs.
More informationAxle load calculations
All types of transportation work using trucks require the truck chassis to be supplemented by some form of bodywork. The aim of axle load calculations is to optimise the chassis and bodywork location.
More informationHASSE & WREDE VISCO DAMPER AFTER SALES SERVICE. Visco damper AFTER SALES SERVICE
HASSE & WREDE VISCO DAMPER AFTER SALES SERVICE Visco damper AFTER SALES SERVICE 2 HASSE & WREDE VISCO DAMPER AFTER SALES SERVICE FUNCTION A viscous damper consists of a housing which comprises an inertia
More informationWeight approx. [kg] II39908FA BZ Part No. Type No. Type Push Rod Seal TÜV Inspection Report
Commercial Vehicle Systems Product DATA PD-403-200 Function This range of Brake Chambers is used on axles fitted with drum brakes. The single diaphragm cylinder provides the service brake function. In
More informationHeavy-Duty Trailers, Cargo/Rolltrailers and Container Chassis for Ports, Industry and Distribution
Heavy-Duty Trailers, Cargo/Rolltrailers and Container Chassis for Ports, Industry and Distribution Industrial trailers for your specific transportation task Industrial trailer with turntable steering 4
More informationBattery Voltage, Overload Protected Hot only in Start & Run 15 GN (green)
Wiring Diagrams Design of Wiring System Determine and Define of Wires Circuit Numbers and Wire Identification will be done according the World-wide Engineering Drafting Standard WH-110-01. The circuit
More informationRigid 8 2. Rigid 8 4
DRIVE / CHASSIS HEIGHT / WHEELBASE (dimensions in dm) Rigid Rear 34 40 40 Rigid 6 2 Rear 48 48 48 Rigid 6 4 Rear Rigid 8 2 Rear Pusher Tridem 62 Rear Tag Tridem Rigid Pusher Tridem 64 64 53 53 47 1 chassis
More informationFeed-in management with Solar-Log
Feed-in management with Solar-Log 1 Publisher: Solare Datensysteme GmbH Fuhrmannstr. 9 72351 Geislingen-Binsdorf Germany International Support Tel.:+49 7428 9418-640 Fax:+49 7428 9418-280 E-mail: support@solar-log.com
More informationLUCAS ACE - System Overview
LUCAS ACE - System Overview The Active Corner Enhancement system manufactured by Rover Group Lucas appears to have been produced specifically for the Land Rover Discovery series II to address the poor
More informationOverview. Hazard Alert Messages
Issued 07-12 Technical Bulletin Issued 1 Technical 07-12 Bulletin Trailer ABS with Roll Stability Support (RSS 1M) for Constant Power Trailers with Air or Mechanical Suspensions 2S/1M with Roll Stability
More informationWiring concept for ACV (FACS)
1. General electric trailer supply connection The tractor circuit provides through T-distributions the entire electric power supply for the trailer, parallel for: - the ACV / FACS interface (for automated
More informationTechnical Report. No. KO250.3E. on the TRAILER CONTROL MODULE
Technical Report No. KO250.3E on the TRAILER CONTROL MODULE Mobilität TÜV NORD Mobilität GmbH & Co. KG IFM Institute for Vehicle Technology and Mobility Adlerstraße 7 45307 Essen Tel.: +49 (0)201 825-4120
More informationTrailers Catalogue AB Umega Tel. (389) Metalo 5, LT Utena Fax (389)
Trailers Catalogue SPA3-3 way tipping trailer Body frame: Body sides are made of profiled steel sheets, sides of 2 mm steel, body flor made of 3 mm steel. All body sides are removable; Chassis: Strong
More informationDaymak Drive Application ios. User Guide
Daymak Drive Application ios User Guide Thank You Thank you for your purchase of our Daymak product. By choosing to utilize an electric vehicle, you are actively doing your part to reduce your carbon footprint.
More informationAir Processing Unit ZB44..
Systems for Commercial Vehicles Service Manual Air Processing Unit ZB44.. Disclaimer The information contained herein is intended for the exclusive use of trained persons within the commercial vehicle
More informationEnergy generation and storage
Energy generation and POWER CONVERTER AT A GLANCE n Energy generation from regenerative energy sources n Storage systems ranging from battery solutions to power-to-gas n Converter technology for low voltage-level
More informationElectronic Function & Safety Assessment Test Report
Electronic Function & Safety Assessment Test Report Mobilität Approval Report No: EB 124.4E TÜV NORD Mobilität GmbH & Co. KG IFM Institute for Vehicle Technology and Mobility Adlerstraße 7 45307 Essen
More informationSD Bendix MV-3 Dash Control Module DESCRIPTION. Bottom View
SD-03-3415 Bendix MV-3 Dash Control Module MOUNTING PLATE MOUNTING HOLES (4) Dual Circuit SUPPLY Check VALVE AUXILIARY PORT (Optional) delivery DESCRIPTION secondary supply Trailer delivery FIGURE 1 -
More informationOverweight permit application
Notes to applicants Combined Forms NZTA 803 and NZTA 804 - Updated July 2017 1. The information requested is required to process any permit application. Please refer to page 4 for an explanation of the
More informationInnovative Vehicle Solutions
INSTALLATION Installation GUIDE Guide Innovative Vehicle Solutions U-ABS Installation Guide Notes on the use of this manual This manual has been designed to assist personnel in satisfactory installation
More informationKLP Kiepe Electric GmbH Test and Measuring SERVICES
Test and Measuring THE AUTOMATIC TEST SYSTEM KIEPE ATS The Automatic Test System Kiepe ATS is a function tester for electronic modules and control devices. The Kiepe ATS can be used to test all kinds of
More informationVehicle Stability Function
Prepared by AMEVSC Secretary AMEVSC-03-04e Vehicle Stability Function Directional Control Roll-over Control A functional overview with regard to commercial vehicles 1 Definitions * Vehicle Stability Function
More informationCEMA position on draft braking regulation, 4 June 2008 ENTR/F1/ /rev16
CEMA PT16 N05Rev CEMA position on draft braking regulation, 4 June 2008 ENTR/F1/5030-99/rev16 CEMA is the European association representing the agricultural machinery industry. It represents the industry
More information1. General Information
1. 1.2 MH-55 Dimensions 1. All specifications may vary, always consult DBT Australia Pty Limited to obtain current information before applying critical loads. Capacities Tractive effort, Maximum Winch
More informationINSTALLATION/SERVICE MANUAL
MANUAL TM Stability Module (L31288W) Important Notices Product Options This manual has been designed to assist personnel in satifactory installation of Haldex ITCM Stability Module onto semi and full trailers.
More informationCEMA PT16 N09Rev2. Reference document: ENTR_F1_ _rev 16 v Article / clause Original text Proposal from CEMA Rationale and
CEMA PT16 N09Rev2 Reference document: ENTR_F1_030-99_rev 16 v030908 Article / clause Original text Proposal from CEMA Rationale and Art., clause 7 The fitment of anti-lock braking systems (ABS) is not
More informationABS Operator s Manual
ABS Operator s Manual Bendix Antilock Brake Systems With optional advanced antilock braking features: Automatic Traction Control (ATC) and RSP Roll Stability System Read, understand and follow the information
More informationRE / Central Hydraulics Valve LT43 for Tractors with Priority Function for Steering and Trailer Brake and Pilot Oil Valve.
Central Hydraulics Valve LT43 for Tractors with Priority Function for Steering and Trailer Brake and Pilot Oil Valve RE 66 235/07.95 Characteristics Input element with priority and pilot oil valve for
More information} Rev.1/Add.12/Rev.6/Amend.3
30 December 2009 AGREEMENT CONCERNING THE ADOPTION OF UNIFORM TECHNICAL PRESCRIPTIONSFOR WHEELED VEHICLES, EQUIPMENT AND PARTS WHICH CAN BE FITTEDAND/OR BE USED ON WHEELED VEHICLES AND THE CONDITIONS FOR
More informationTo increase the height of the trailer increase the length, to reduce the height, decrease the length of the link.
RIDE HEIGHT (CONTINUED) 8.8.2. Trailer Suspension The trailer suspension is set at the factory and should always return to this setting when the height control valve is returned to the central position,
More informationSB Issue date: July 18, 2012
SB-08-162 Issue date: July 18, 2012 Bendix TABS-6 TroubleShooting Guide Bendix has developed the attached TroubleShooting Guide to provide an easy to follow method of isolating and correcting problems
More informationDocument ID# Buick LeSabre
http://127.0.0.1:9001/servlets/blobshtml?shtmlfile=633088&evc=sm&pubid=262&cellid... Page 1 of 3 Document ID# 633088 DTC C1214 Circuit Description The system relay is energized when the ignition is ON.
More informationElectronic Brake by Wire
Electronic Brake by Wire Angelo Grasso, Wabtec Martin Deuter, Knorr Bremse Ugo Prosdocimi, Eletech CONNECTA has received funding from the European Union s Horizon 2020 research and innovation programme
More informationHIGHSPEED / COACHES LEADING IN ENTRANCE SYSTEMS FOR HIGHSPEED TRAINS AND PASSENGER COACHES
HIGHSPEED / COACHES 1 LEADING IN ENTRANCE SYSTEMS FOR HIGHSPEED TRAINS AND PASSENGER COACHES 2 PROVEN AND RELIABLE: ENTRANCE SYSTEMS UP TO 80 KM/H HIGHSPEED TRAINS AND PASSENGER COACHES SYSTEMS FOR RAIL
More informationInternational A26 (2017)
International A26 (2017) Overview: Cruise Control A26_CRUISE_CONTROL_06222017 Cruise Control TABLE OF CONTENTS General Overview: Cruise Control... 1 BASIC CRUISE CONTROL...1 ADVANCED CRUISE CONTROL...1
More informationSplined Disc Brake Disc 22.5
Service Manual Splined Disc Brake Disc 22.5 Service kits Description / Function Service instructions Service Manual Disclaimer The information contained herein is intended for the exclusive use of trained
More informationOperating and Installation BPW THE QUALITY FACTOR. Version 1.4. ECO Tronic EBS. Operating and Installation Instructions. Version 1.
Operating and Installation Instructions Version.4 BPW THE QUALITY FACTOR ECO Tronic EBS. Operating and Installation Instructions Version.4 BPW Operating and Installation Instructions Introduction Page.
More informationKögel Flatbed Trailer
Kögel Flatbed Trailer Illustration similar / can include special equipment Why so much talk about the art of engineering? Because there is genius in it and because prowess is behind it. Comprehensive competence
More informationAirBrakeSystems. "Safety - Technology - Support" WABCO TRAILER EBS INSPECTION & SERVICE PROCEDURES AIR BRAKE SYSTEMS PTY LTD
WABCO TRAILER EBS INSPECTION & SERVICE PROCEDURES AIR BRAKE SYSTEMS PTY LTD 16 Leighton Place, Hornsby NSW 2077 Tel: 02 9482 1733 Fax: 02 9476 1828 "" E: sales@airbrake.com.au W: www.airbrake.com.au Additional
More informationInstallation Instructions Vario Compact ABS (VCS)
Installation Instructions Vario Compact ABS (VCS) 1 Installation Instructions Vario Compact ABS (VCS) Installation of the Vario Compact ABS developed by WABCO is very easy and requires very little effort.
More informationTAG LIFT AXLE SUSPENSION SERVICE MANUAL- 37 T
TAG LIFT AXLE SUSPENSION SERVICE MANUAL- 37 T ` Page 0 CONTENT SI.NO Description Page No. 1 Suspension Specification 2 2 Pre-Installation Notes 2 3 Suspension Parts Description 3 4 Dismantling Procedure
More informationLED Diagnostic Display. ABS Modulator. Connector (MOD1) Supply Port 1/2" NPT MC-30 CONTROLLER INTRODUCTION
SD-13-4834 Bendix MC-30 Trailer ABS Controller Assembly LED Diagnostic Display 30-Pin Connector ABS Modulator Connector (MOD1) Control Port 1/4" NPT Delivery Ports 3/8" NPT (x4) TABLE OF CONTENTS PAGE
More informationINSTALLATION/SERVICE MANUAL
INSTALLATION/SERVICE MANUAL External Pressure Sensor Transducer Intelligent Trailer (L31295W) haldex.com Important Notice The products described within this literature, including without limitation, product
More informationMaxxForce 11 and 13 (2010)
MaxxForce 11 and 13 (2010) Overview: In Cab Control NAV_PTOIC_070511 In-Cab Control TABLE OF CONTENTS General Overview: In-Cab Control... 1 Description and Operation... 1 OPERATION...1 STATIONARY VARIABLE...1
More informationT E S T R E P O R T N o. E B E
T E S T R E P O R T N o. E B 1 8 1. 2 E on the regularity of the braking system of a vehicle in accordance with the regulations of the EC Directive 71/320/EEC or the UN-ECE Regulation no. 13 when installing
More informationFitting Instructions: Sprint ST (1050cc) & Tiger (1050cc) Top Box Kit - A & A
Fitting Instructions: Sprint ST (050cc) & Tiger (050cc) Top Box Kit - A9508066 & A9508067 Throughout this operation, ensure that the motorcycle is stabilised and adequately supported to prevent risk of
More informationForward tipping dumper Note: It is recommended that you read the Supporting Information page before you read this factsheet.
Forward tipping dumper Note: It is recommended that you read the Supporting Information page before you read this factsheet. Preparation and completing work (Preparation) Forward tipping dumpers are commonly
More informationGEMÜ 539 esydrive Motorized globe valve
esydrive Motorized globe valve Features Linear or modified equal-percentage control characteristics High flow rates Force and speed are variably adjustable Extensive diagnostic facilities Operable via
More informationNewcastle Weighing Services Pty Ltd
Newcastle Weighing Services Pty Ltd Revision Sheet Revision 1 Marcus Graham Split Weighing in ClearWeigh This document describes the use of the split weighing facility in the ClearWeigh Touch Terminal
More informationService Manual AIR PROCESSING UNIT ZB44.. Y (EN - Rev. 003) NOVEMBER l. 20 l. ZB44.. type APU. 23 Ø nozzle defined in procedure
Y000 - (EN - Rev. 00) NOVEMBER 04 Service Manual T T6 0 l T7 G Pressurised air 8 Bar Nozzle Check valve G T9 T G T T0 0. l T ZB44.. type APU T G4 0. l T G Ø nozzle defined in procedure T4 0. l T G6 Used
More informationTrailed Sprayers. Knight Farm Machinery is based in the rural county of Rutland at the heart of the UK arable farming area.
Since its formation in 1984 Knight Farm Machinery has become one of the UK s leading manufacturers of crop sprayers and cultivation equipment, combining reliability and practicality with a high degree
More informationSECTION 25 FRONT AXLE. Chapter 2 Terraglide (Front Axle Suspension)
SECTION 25 MECHANICAL FRONT AXLE CHAPTER 2 1 SECTION 25 FRONT AXLE Chapter 2 Terraglide (Front Axle Suspension) CONTENT Section Description Page 25 000 Specifications................................................................
More informationWSX12/14 WSXD20. Electric Stacker Trucks kg kg kg.
WSX12/14 Electric Stacker Trucks 1.200 1.400 2.000 www.clarkmheu.com DIMENSIONS WSX12/14 For corresponding data see specification chart. SPECIFICATIONS Product Specifications acc. to VDI 2198 Specifications
More informationStandard Features 200-600V, 50/60Hz input power supply Built-in run rated (AC1) By-pass contactor up to 820 A * Rated 450% current Conformal coated circuit board Voltage ramp or current limit start modes
More informationKnorr-Bremse RailServices (UK) Ltd Springburn
Knorr-Bremse RailServices (UK) Ltd Springburn 79 Charles Street, Springburn Glasgow United Kingdom G21 2PS has been assessed and approved in accordance with the requirements of RISAS/003 for 17 product
More informationDESCRIPTION & OPERATION
DESCRIPTION & OPERATION ANTI-LOCK BRAKING 1998-99 BRAKES Anti-Lock/TCS - Corvette The Anti-Lock Brake System (ABS) and Traction Control System (TCS) increases vehicle control during severe deceleration
More information