INHIBITOR SWITCH AT-50. 5) Disconnect the inhibitor switch connector.

Size: px

Start display at page:

Download "INHIBITOR SWITCH AT-50. 5) Disconnect the inhibitor switch connector."

Stephen Anthony
5 years ago
Views:

1 INHIBITOR SWITCH B: ADJUSTMENT 1) Shift the select lever to N range. 2) Loosen the three inhibitor switch securing bolts. 3) Insert the ST as vertical as possible into the holes in inhibitor switch lever and switch body. ST STOPPER PIN ST C: REMOVAL 1) Set the vehicle on a lift. 2) Move the select lever to N range. 3) Remove the air cleaner case. () <Ref. to IN(H4SO)-5, REMOVAL, Air Cleaner 4) Remove air intake chamber. () <Ref. to IN(H6DO)-6, REMOVAL, Air Intake Chamber.> 5) Disconnect the inhibitor switch connector. AT ) Tighten the three inhibitor switch bolts. 3.5 N m (0.35 kgf-m, 2.5 ft-lb) 5) Repeat the above checks. If the inhibitor switch is determined to be faulty, replace it. AT ) Remove the inhibitor switch connector from stay. 7) Lift-up the vehicle. 8) Remove the front and center exhaust pipes. <Ref. to EX(H4SO)-5, REMOVAL, Front Exhaust <Ref. to EX(H6DO)-5, REMOVAL, Front Exhaust 9) Remove the snap pin and washer from range select lever. ( C ) ( D ) AT (D) Snap pin Washer AT-50

2 INHIBITOR SWITCH AUTOMATIC TRANSMISSION 10) Remove the plate assembly from transmission case. 13) Remove the inhibitor switch from transmission. Plate ASSY 11) Remove the bolts. AT AT ) Disconnect the inhibitor switch harness connector from inhibitor switch. AT ) Move the range select lever to parking position (left side). AT AT-51

3 INHIBITOR SWITCH D: INSTALLATION 1) Connect the inhibitor switch harness connector to inhibitor switch. 2) Install the inhibitor switch to transmission case. 6) Install the plate assembly to transmission. T: 25 N m (2.5 kgf-m, 18.1 ft-lb) T AT AT ) Move the range select lever to neutral position. 4) Place the inhibitor switch on specified position, and then tighten the bolts for inhibitor switch using ST. ST STOPPER PIN 3.5 N m (0.36 kgf-m, 2.6 ft-lb) Plate ASSY 7) Install the washer and snap pin to range select lever. ST ( C ) ( D ) AT AT (D) Snap ring Washer 5) Install the select cable to range select lever. 8) Install the front and center exhaust pipes. <Ref. to EX(H4SO)-6, INSTALLATION, Front Exhaust <Ref. to EX(H6DO)-6, INSTALLATION, Front Exhaust 9) Lower the vehicle. 10) Install the inhibitor switch connector to stay. AT-52

4 INHIBITOR SWITCH AUTOMATIC TRANSMISSION 11) Connect the inhibitor switch connector. AT ) Install the air cleaner case. () <Ref. to IN(H4SO)-5, INSTALLATION, Air Cleaner 13) Install air intake chamber. () <Ref. to IN(H6DO)-6, INSTALLATION, Air Intake Chamber.> 14) Inspect the inhibitor switch. <Ref. to AT-49, IN- SPECTION, Inhibitor Switch.> AT-53

5 FRONT VEHICLE SPEED SENSOR 13.Front Vehicle Speed Sensor A: REMOVAL 1) Set the vehicle on a lift. 2) Disconnect the ground cable from battery. 25 N m (2.5 kgf-m, 18.1 ft-lb) ( C ) AT ) Remove the air cleaner case. () <Ref. to IN(H4SO)-5, REMOVAL, Air Cleaner 4) Remove air intake chamber. () <Ref. to IN(H6DO)-6, REMOVAL, Air Intake Chamber.> 5) Disconnect the transmission connector. Transmission connector AT AT ) Remove the pitching stopper. <Ref. to AT-46, REMOVAL, Transmission Mounting System.> 7) Remove the transmission connector from stay. 8) Lift-up the vehicle. 9) Clean the transmission exterior. 10) Drain the ATF completely. Tighten the ATF drain plug after draining the ATF. Replace the gasket with a new one. Oil pan Drain plug Differential oil drain plug 11) Remove the front, center, rear exhaust pipes and muffler. <Ref. to EX(H4SO)-5, REMOVAL, Front Exhaust, <Ref. to EX(H4SO)-9, REMOVAL, Rear Exhaust and <Ref. to EX(H4SO)-10, RE- MOVAL, Muffler.> <Ref. to EX(H6DO)-5, REMOVAL, Front Exhaust, <Ref. to EX(H6DO)-8, REMOVAL, Rear Exhaust and <Ref. to EX(H6DO)-9, RE- MOVAL, Muffler.> 12) Remove the shield cover. 13) Remove the propeller shaft. <Ref. to DS-14, REMOVAL, Propeller Shaft.> 14) Place the transmission jack under transmission. Make sure that the support plates of transmission jack don't touch the crossmember. 15) Remove the transmission rear crossmember bolts. AT ) Lower the AT jack. Do not separate the AT jack and transmission. AT-54

3. Manual Transmission Assembly

3. Manual Transmission Assembly A: REMOVAL 1) Open the front hood fully, and support with stay. 2) Disconnect the ground cable from battery. 3) Remove the air intake duct and cleaner case. (Non-turbo model)