|
|
- Maryann Lambert
- 5 years ago
- Views:
Transcription
1 Page 1 of Pontiac GRAND PRIX Submodel: Engine Type: V6 Liters: 3.8 Fuel Delivery: FI Fuel: GAS Oil Pan Replacement Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement. Remove the air cleaner intake duct. Refer to Air Cleaner Inlet Duct Replacement. Install the engine support fixture. Refer to Engine Support Fixture. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Drain the engine oil and remove the oil filter. Refer to Engine Oil and Oil Filter Replacement. Remove the power steering oil cooler pipe brackets from the frame. Disconnect the oil level sensor electrical connector (10). Remove the oil level sensor wiring harness bolt and reposition the oil level sensor wiring harness. Remove the catalytic converter (3) to the right exhaust manifold pipe stud nuts (2) and reposition the catalytic converter. Remove the engine mount bracket and the engine mount. Refer to Engine Mount Replacement. Remove the torque converter covers. Refer to Torque Converter Cover Replacement for the 4T65 E automatic transmission. Lower the vehicle. Using the engine support fixture raise the engine to gain access for the oil pan removal. Raise the vehicle. Remove the oil level sensor, located in the oil pan, before the oil pan is removed. The sensor may be damaged if the oil pan is removed first.
2 Page 2 of 5 Remove the oil level sensor. Remove the oil pan bolts. Remove the oil pan. Remove the oil pump pipe screen assembly and the oil pan gasket. Clean the following parts: Oil pump screen mating surfaces Oil pan flanges Oil pan rail Front cover Rear main bearing cap Threaded holes Installation Procedure
3 Page 3 of 5 Install the oil pump pipe screen assembly. Refer to Fastener Notice in the Preface section. Install the oil pump pipe screen bolts. the bolts to 15 N m (11 lb ft). Important For aluminum oil pans, begin with step 6. For steel oil pans, skip steps 6 and 7. For steel oil pans, apply a continuous bead 6.35 mm (0.25 in) thick of RTV sealer GM P/N (Canadian P/N ) to the topside of the new windage tray gasket. Apply the RTV sealant directly over the sealing bead. Install the NEW windage tray gasket onto the engine. Apply a continuous bead 6.35 mm (0.25 in) thick of RTV sealer GM P/N (Canadian P/N ) to the bottom side of the new windage tray gasket. Apply the RTV sealant directly over the sealing bead.
4 Page 4 of 5 For aluminum oil pans, apply a continuous bead 6.35 mm (0.25 in) thick of RTV sealer GM P/N (Canadian P/N ), ensuring that the sealer also completely fills the groove in the oil pan. To ensure proper sealing, apply additional sealer at the four points called out in the illustration (1). Install the oil pan and oil pan windage tray gasket, if applicable. Clean the oil pan bolts of all debris. Apply one drop of GM P/N (Canadian P/N ) to each bolt. Install the oil pan bolts. the oil pan bolts to 14 N m (125 lb in). Install the oil level sensor, located in the oil pan, after the oil pan is installed. The sensor may be damaged if the oil level sensor is installed first. Install the oil level sensor. the sensor to 20 N m (15 lb ft). Install the torque converter covers. Refer to Torque Converter Cover Replacement for the 4T65 E automatic transmission. Install the engine mount and the engine mount bracket. Refer to Engine Mount Replacement.
5 Page 5 of 5 Install the catalytic converter (3) to the right exhaust manifold. Install the catalytic converter pipe stud nuts (2). the nuts to 32 N m (24 lb ft). Install the oil level sensor wiring harness and the oil level sensor wiring harness bolt to the engine. the bolt to 10 N m (89 lb in). Connect the oil level sensor electrical connector (10). Install the power steering oil cooler pipe brackets to the frame. Install the engine oil filter. Lower the vehicle. Remove the engine support fixture. Install the right and left engine mount struts. Refer to Engine Mount Strut Replacement - Right Side and Engine Mount Strut Replacement - Left Side. Fill the crankcase with engine oil. Refer to Engine Oil and Oil Filter Replacement. Install the air cleaner intake duct. Refer to Air Cleaner Inlet Duct Replacement. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. Inspect for leaks. Top of Page EBSCO Support Site Privacy Policy Terms of Use Copyright 2010 EBSCO Industries, Inc. All rights reserved EBSCO Publishing Green Initiatives
Oil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More information2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID:
xtooltipelement Service Information 2005 Chevrolet Equinox Equinox VIN L Service Manual Engine Engine Mechanical - 3.4L Repair Instructions - On Vehicle Document ID: 1383623 Engine Front Cover Replacement
More information2. Remove the intake manifold cover. Refer to Intake Manifold Cover Replacement.
VALVE COVER GASKET Valve Rocker Arm Cover Replacement - Left Side Removal Procedure 1. Partially drain the cooling system. Refer to Cooling System Draining and Filling (LZE, LZ4, LZG, 9C1, 9C3, GE47716
More informationIntake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
More informationIntake Manifold Replacement
Page 1 of 13 Your Current Vehicle: 2008 Cadillac STS Intake Manifold Replacement Intake Manifold Replacement Removal Procedure 1. Turn the ignition OFF. 2. Remove the fuel injector sight shield. Refer
More informationVehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator
More informationCylinder Head Installation - Left Side
Cylinder Head Installation - Left Side Tools Required J 36660-A Torque Angle Meter 1. Install the cylinder head locator dowel pins, if necessary. 2. Inspect the cylinder head locator dowel pins for proper
More informationIntake Manifold Removal (Upper)
Intake Manifold Removal (Upper) Disconnect the vacuum lines from the upper intake manifold. Disconnect the MAP sensor electrical connector. Remove the MAP sensor screws. Remove the MAP sensor. Remove the
More informationNOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
Fig. 2: Lower Intake Manifold Bolt Tightening Sequence INTAKE MANIFOLD (UPPER) NOTE: Do not disassemble upper intake manifold from lower intake manifold unless replacement of one of the components is necessary.
More information2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
More information1988 Ford F-350 PICKUP
1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are
More informationPage 1 of 7 2003 Chevrolet SILVERADO 1500 Submodel: Engine Type: V8 Liters: 5.3 Fuel Delivery: FI Fuel: GAS Instrument Panel Carrier Replacement Removal Procedure Warning! Refer to Battery Disconnect Caution
More informationROAD RACE BAFFLE for LT OIL PANS P/N
ROAD RACE BAFFLE for LT OIL PANS P/N 302-30 Instruction Sheet 199R11191 NOTE: This instruction sheet is intended for installation after a Holley LT oil pan (302-20) has previously been installed. If installing
More informationLubricating Oil Pan
007-025 Lubricating Oil Pan Preparatory Steps Batteries can emit explosive gases. To reduce the possibility of personal injury, always ventilate the compartment before servicing the batteries. To reduce
More informationREMOVAL. Fig Sized for Print
ALLDATA Online - 2000 Dodge Truck Grand Caravan FWD V6-3.3L VIN R - Intake M... Page 1 of 10 REMOVAL 1. Remove windshield wiper module. 2. Perform fuel system pressure release procedure (before attempting
More informationPage 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
More information2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
More information2001 Chevrolet Corvette V8-5.7L VIN G
1 of 14 2/21/2013 10:34 AM 2001 Chevrolet Corvette V8-5.7L VIN G Vehicle» Engine, Cooling and Exhaust» Engine» Oil Pan» Service and Repair Oil Pan Replacement Removal Procedure 1. 2. 3. Remove the front
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» RH Valve Cover RH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationSikky Oil Pan Install Guide
Sikky Oil Pan Install Guide **If you have a double chain timing belt or after market oil pump setup then further modifications may need to be made in order for the pan to fit.** Remove starter Remove plastic
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More informationValve Rocker Arm and Push Rod Installation (6.2L LS3)
9. Tighten the cylinder head bolts: 10.1. Tighten the M11 cylinder head bolts (1-10) a first pass in sequence to 30 N m (22 lb ft). 10.2. Tighten the M11 cylinder head bolts (1-10) a second pass in sequence
More information1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
More informationDisconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
More informationSolenoid Valve VCB, Replacement, D13F. This information covers the procedures for replacing the VCB solenoid valve on the Volvo D13F engine.
Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 10.2007 253 67 1(9) Solenoid Valve VCB, Replacement D13F Solenoid Valve VCB, Replacement, D13F This information
More informationKeeping You Cool Under Pressure
Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal
More information3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More informationOIL PAN with DRAG RACE BAFFLING P/N
OIL PAN with DRAG RACE BAFFLING P/N 302-22 Instruction Sheet 199R11161 CONGRATULATIONS on your purchase of a Holley LT Retro-fit Oil Pan! We feel that you have purchased the finest performance oil pan
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationM-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly
More informationPage 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More informationPage 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
More informationFUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID#
FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID# 824435 Fuel Tank Replacement (Cab/Chassis Front) Removal Procedure http://dh.identifix.com/searchfixes/index?roid=158586813&vid=2018330&vsm=4&hasbookmark=0&locationid=2#kw=fuel+pump&soption=1&vetid=8&stmode=1&paging=&smode=2&position=assetcat_9
More informationIntake manifold / gasket, replacing
Page 1 of 9 Intake manifold / gasket, replacing Special tools: 999 5723, 951 2666 Preparation Disconnect the battery negative lead. First read Note when disconnecting/connecting the battery lead. Drain
More information2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
More informationEngine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
More informationIntake Manifold Replacement
ALLDATA Online - 2001 Cadillac DeVille V8-4.6L VIN 9 - Intake Manifold Replacement Page 1 of 15 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's
More informationCatalytic Converter: Service and Repair
2007 GMC Truck Envoy 4WD V8-5.3L Copyright 2009, ALLDATA 10.10 Page 1 Catalytic Converter: Service and Repair Catalytic Converter Replacement (5.3L and 6.0L Engines) Removal Procedure 1. Raise and suitably
More information2000 Econoline Workshop Manual. 3. Install the upper intake manifold. 2. NOTE: Tighten the bolts in two stages.
2. NOTE: Tighten the bolts in two stages. Tighten the bolts in the sequence shown. Stage 1: Tighten to 2 Nm (18 lb-in). Stage 2: Tighten to 10 Nm (89 lb-in). 3. Install the upper intake manifold. Position
More informationCOMPONENTS ILLUSTRATION
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION REMOVAL 1. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (a) Remove the windshield wiper motor and link assembly. 2. REMOVE COWL BODY MOUNTING REINFORCEMENT
More information2001 Ranger Workshop Manual. 1. Drain the cooling system. For additional information, refer to Section
Exhaust Gas Recirculation (EGR) Valve 2.3L 1. Drain the cooling system. For additional information, refer to Section 303-03. 2. Disconnect the battery ground cable. For additional information, refer to
More information2000 Chrysler SEBRING
2000 Chrysler SEBRING Submodel: JX Engine Type: V6 Liters: 2.5 Fuel Delivery: FI Fuel: GAS 2.0L SOHC and 2.4L DOHC Engines The intake manifold for the 2.0L SOHC engine is a long branch design made of a
More informationGM 4T65E Installation Tips
GM 4T65E Installation Tips WARNING: DO NOT operate vehicle without installing a new transmission oil cooler. We recommend installing a Hayden 1403 or 1404. Bypass the radiator and install the new cooler.
More informationOil Pan July DDC-SVC-MAN-0081 DD Platform Installation of the Oil Pan Added graphics, additional torque specs.
7 17-13 1 7 17-13 SUBJECT DATE Oil Pan July 2013 Additions, Revisions, or Updates Publication Number / Title Platform Section Title Change DDC-SVC-MAN-0081 DD Platform Installation of the Oil Pan Added
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More information2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
More informationFUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G )
PUBLISHED: 10-OCT-2017 2010.0 RANGE ROVER SPORT (LS), 303-01 ENGINE - V8 S/C 5.0L PETROL FUEL PUMP CAMSHAFT TIMING ADJUSTMENT (G1473741) GENERAL PROCEDURES 19.90.17 HIGH PRESSURE FUEL TIMING CHECK AND
More informationEXHAUST SYSTEM AND INTAKE MANIFOLD
J EXHAUST SYSTEM AND INTAKE MANIFOLD 11-1 EXHAUST SYSTEM AND INTAKE MANIFOLD CONTENTS page EXHAUST SYSTEM... 1 EXHAUST SYSTEM DIAGNOSIS... 2 page SERVICE PROCEDURES... 3 TORQUE SPECIFICATIONS... 10 EXHAUST
More information2000 Chevrolet Blazer
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE. 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws 3. Remove
More informationIN-VEHICLE SERVICING > VALVE COVER - RH
Page 1 of 20 Service Manual: ENGINE - 5.4L (3V)- F-150 & MARK LT IN-VEHICLE SERVICING > VALVE COVER - RH 2008 Ford Pickup 5.4L Eng F150 Material Item Specification Motorcraft Metal Surface Prep ZC-31 PAG
More informationCourse Code: N13 Engine Exhaust Manifold Service Study Guide
Course Code: 8573 2015 N13 Engine Exhaust Manifold Service Study Guide 2015 Navistar, Inc. 2701 Navistar Drive, Lisle, IL 60532. All rights reserved. No part of this publication may be duplicated or stored
More informationWater Pump Replacement (L4)
2011 Chevrolet Equinox Equinox, Terrain VIN L Service Manual Water Pump Replacement (L4) Special Tools EN-43651 Water Pump Holding Tool For equivalent regional tools, refer to Special Tools. Removal Procedure
More information10/30/2018 Intake Manifold Replacement (RPOs LY2/LY6) 2007 GMC Truck Yukon Denali MotoLogic
2007 Yukon Denali Applies to: 4.8L, 5.3L, 6.0L and 6.2L Report a problem with this article Removal Procedure 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Resonator Outlet Duct Replacement.
More information1 of 8 12/12/2012 6:08 PM 1999 Chevrolet Express - 2WD Express, Savana VIN G Service Manual Engine Engine Mechanical - 6.5L Repair Instructions Engine Replacement Removal Procedure Tools Required J 36857
More informationInstallation Instructions
Installation Instructions 2.0T FSI Intake Manifold: Featuring better flow, higher boost capacity, 40% larger plenum volume, and integrated flapper delete; this product will take your 2.0L VW TSI and FSI
More informationINTAKE/EXHAUST SYSTEM 7 C TURBOCHARGER
INTAKE/EXHAUST SYSTEM 7 C TURBOCHARGER Table Of Contents Page Identification.................................. 7C-1 Torque Specifications.......................... 7C-1 Sealants.....................................
More informationExhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
More informationOil Module in the Inner V
Oil Module in the Inner V There are numerous oil supply passages under a cover in the V of the engine. The cover is bolted directly to the cylinder block, with a metal gasket positioned between them. Oil
More informationCylinder Head Assembly: Service and Repair Replacing the Cylinder Head and Gasket
2002 Volvo V40 L4-1.9L Turbo VIN 29 B4204T3 Copyright 2009, ALLDATA 10.10 Page 1 Cylinder Head Assembly: Service and Repair Replacing the Cylinder Head and Gasket Cylinder Head/Gasket, Replacing Special
More informationEngine Front Cover. Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1) or equivalent. Support Bar, Engine 303-F070
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Engine Front Cover Special Tool(s) Lifting Bracket, Engine (2 required) 303-D087 (D93P-6001-A1)
More informationFastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
More informationGM ENGINE REPAIR. Maintenance GM 2.4 LITER ENGINE GLC20-35VX (GC/GLC VX, GC/GLC055SVX) [A910]; GLP/GDP20-35VX (GP/GLP/GDP VX) [B875]
Maintenance GM ENGINE REPAIR GM 2.4 LITER ENGINE GLC20-35VX (GC/GLC040-070VX, GC/GLC055SVX) [A910]; GLP/GDP20-35VX (GP/GLP/GDP040-070VX) [B875] PART NO. 524223755 600 YRM 1121 SAFETY PRECAUTIONS MAINTENANCE
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More informationSECTION C Engine 6.4L Diesel
303-01C-i Engine 6.4L Diesel 303-01C-i SECTION 303-01C Engine 6.4L Diesel CONTENTS PAGE SPECIFICATIONS... 303-01C-2 303-01C-2 Engine 6.4L Diesel 303-01C-2 SPECIFICATIONS Material Gasket Maker TA-16 Motorcraft
More informationCylinder head/gasket, replacing
1(16) Cylinder head/gasket, replacing Special tools: 951 2666, 951 2767, 999 5450, 999 5452, 999 5454, 999 5670, 999 5718, 999 5719, 999 5750, 999 5972 Removing the cylinder head gasket Note! As the illustrations
More informationPiston Cooling Nozzle, Replacement
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces Service Bulletin 221-49, Piston Cooling, dated (1.2007), publication no. PV776-20177472. DService Bulletin Trucks Date Group
More informationReproduction. Not for. Illustrated Parts List 49E700. Model Series TYPE NUMBERS FORM MS /17/2014 FILE IN SECT. 2 OF SERVICE MANUAL 49E700
FORM MS10562 10/17/2014 FILE IN SECT. 2 OF SERVICE MANUAL 49E700 Illustrated Parts List Model Series 49E700 TYPE NUMBERS 0001. PRINTED IN U.S.A. COPYRIGHT by BRIGGS & STRATTON CORPORATION All rights reserved.
More informationPage 1 of 6 Section 03-01C: Engine, 7.5L MFI 1996 Bronco/F-Series Workshop Manual IN-VEHICLE SERVICE Procedure revision date: 06/19/2000 Cylinder Heads Removal SPECIAL SERVICE TOOL(S) REQUIRED Description
More informationRocker Lever Housing
003-013 Rocker Lever Housing Preparatory Steps Disconnect the air piping from the intake manifold. Remove the rocker lever cover. Refer to Procedure 003-011 in Section 3. Remove the engine brakes, if applicable,
More informationIntake Manifold Replacement
Document ID# 738735 2002 Chevrolet Chevy Suburban - 4WD Print Intake Manifold Replacement Removal Procedure Important: The intake manifold, throttle body, fuel rail, and injectors may
More informationEngine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 1 Technical Service Bulletin # 98-107 Date: 990111 Engine - Timing Chain/Front Cover Revised Procedure Classification: EM98-009 Reference:
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationAJV8 Engine Assembly. AJV8 Engine Assembly
AJV8 Engine Assembly Contents Cylinder Block Dowels, Plugs and Pipes 2 4 Crankshaft Bearing and Cylinder Bore Dimensions 5 9 Bearing Measuring 6 Engine Dimensions and Codes 6 7 Main Bearing Selection Chart
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More information4 December 2017 PN# , , Dodge 6.7L Rumble B SXE (I-00400) 1. BD Rumble B SXE. D o d g e 6. 7 L H P C R Installation Instructions
4 December 2017 PN#1045705, 1045706, 1045708 Dodge 6.7L Rumble B SXE (I-00400) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Rumble B SXE D o d g e 6. 7 L H P C R Installation Instructions
More informationTurbocharger Replacement
Page 1 of 11 2007 Chevrolet Silverado - 4WD Sierra, Silverado VIN C/K Service Manual Engine Engine Mechanical - 6.6L Repair Instructions - On Vehicle Document ID: 1872682 Turbocharger Replacement Removal
More information2004 Toyota CAMRY. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS
2004 Toyota CAMRY Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS REPLACEMENT 1. REMOVE HOOD SU-ASSY 2. REMOVE FRONT WHEEL RH 3. REMOVE ENGINE UNDER COVER LH 4. REMOVE ENGINE UNDER COVER
More information1994 Ford Mustang - Engine Mechanical > Engine Mechanical Components > Timing Chain Cove...
Page 1 of 6 1994 Ford Mustang : Engine Mechanical > Engine Mechanical Components > Timing Chain Cover & Seal > Removal & Installation > 5.0L Engine 5.0L Engine 1. Disconnect the negative battery cable
More informationCorvette Stage X Twin Turbo Installation. Please read the entire instructions as we ve made many changes.
Corvette Stage X Twin Turbo Installation Please read the entire instructions as we ve made many changes. Disconnect battery. Remove plastic fuel rail covers over the valve cover. Remove Air Box in front
More informationNUMBER: S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009
NUMBER: 8 5 09 S.M. REF.: Listed in Table ENGINE: EPA07 MBE 4000 DATE: August 2009 SUBJECT: CYLINDERHEADCOOLANTVENTLINE ADDITIONS, REVISIONS, OR UPDATES Publication Number Platform Section Title Change
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationCondition. Correction
#06-06-04-008B: LNJ Service Engine Soon (SES) Light On, Multiple Powertrain Control Module (PCM) Diagnostic Trouble Code (DTC) P1404 and/or P0404 (Install EGR Valve/Gasket/Pipe/Wiring Harness Connector,Reprogram
More informationEdelbrock Victor II Intake Manifold. For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines Part #7179
For Chrysler 5.7L (Eagle) and 6.1L Gen III HEMI Engines PLEASE study these instructions carefully before beginning this installation. You should be familiar with and comfortable working on your vehicle.
More informationINTAKE AND EXHAUST 15-1 CONTENTS SERVICE ADJUSTMENT PROCEDURES... 2 EXHAUST MANIFOLD EXHAUST PIPE AND MAIN MUFFLER...
I i 15-1 INTAKE AND EXHAUST CONTENTS 110003071 L AIR CLEANER 4.5L Engine>....3 AIR CLEANER 4.8L Engine>....4 EXHAUST MANIFOLD... 10 EXHAUST PIPE AND MAIN MUFFLER... 13 GENERAL INFORMATION.... 2 INTAKE
More informationCrankshaft Rear Seal with Retainer Plate
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/25/2008 Crankshaft Rear Seal with Retainer Plate Special Tool(s) Installer, Crankshaft Rear
More informationThis information covers procedures for replacing the sealant for the crankshaft cover on the Volvo D16F engine.
Volvo Trucks North America Greensboro, NC USA DService Bulletin Trucks Date Group No. Page 1.2008 216 50 1(17) Sealant Crankshaft Cover, Replacement D16F Sealant Crankshaft Cover, Replacement W2005773
More information7-8 CHEVROLET AND GMC BLAZER JIMMY S10 SONOMA _U07.qxd 8/30/05 3:01 PM Page 8 BVC GMC CARS JCK/MJS/KJE 8/22/ S10P-C07
26770_U07.qxd 8/30/05 3:01 PM Page 8 7-8 06025-S10P-C07 06025-S10P-C08 26770_U07.qxd 8/30/05 3:01 PM Page 9 7-9 06025-S10P-C09 26770_U07.qxd 8/30/05 3:01 PM Page 10 7-10 06025-S10P-C10 26770_U07.qxd 8/30/05
More informationDisconnect the tie rod from the steering knuckle (Refer to 19 - STEERING/LINKAGE/TIE ROD END - REMOVAL).
http://arrc.ebscohost.com/articles/f8aa43f0-8786-012b-2f40-fd20d2fb6f.. 1 of 7 8/11/2012 6:14 PM 2007 Dodge RAM 1500 Submodel: TRX4 Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Subarticles (LD)
More informationBD TrackMaster S D o d g e H P C R Installation Instructions
7 July 2016 PN#1045701, 1045702, 1045704 Dodge 6.7L TMS400 (I-00361) 1 BD TrackMaster S400 2008-2012 D o d g e H P C R Installation Instructions 1045701 2008-2009 Dodge 6.7L TMS400 1045702 2010-2012 Dodge
More informationDISASSEMBLY. Engine. Special Tool(s) Locking Tool, Camshaft Phaser Sprocket Special Tool(s)
303-01B-1 DISASSEMBLY Engine Special Tool(s) Remover, Crankshaft Rear Slinger 303-514 (T95P-6701-AH) Special Tool(s) 303-01B-1 Locking Tool, Camshaft Phaser Sprocket 303-1046 Remover, Crankshaft Rear Seal
More informationInstallation Instructions and Warranty Information
Corporate Office: PerTronix Inc. 440 E. Arrow Highway, San Dimas, California 91773 * Phone 909.599.5955 FAX 909.599.6424 Installation Instructions and Warranty Information 6695S 2007-14 5.4/5.8 Ford Mustang
More informationEGR Cooler: Service and Repair Exhaust Gas Recirculation Valve Cooler Replacement
2009 GMC Truck Sierra 2500 2WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA 10.52 Page 1 EGR Cooler: Service and Repair Exhaust Gas Recirculation Valve Cooler Replacement Exhaust Gas Recirculation Valve Cooler
More informationIN-VEHICLE REPAIR. Engine Front Cover
303-01B-1 IN-VEHICLE REPAIR Engine Front Cover Material Item Specification 303-01B-1 Special Tool(s) Motorcraft SAE 5W-20 WSS-M2C930-A Premium Synthetic Blend 3-Jaw Puller Motor Oil 303-D121 XO-5W20-QSP
More informationSECTION A Engine 3.7L
303-01A-i Engine 3.7L 303-01A-i SECTION 303-01A Engine 3.7L CONTENTS PAGE SPECIFICATIONS... 303-01A-2 303-01A-2 Engine 3.7L 303-01A-2 SPECIFICATIONS Material Motorcraft High Performance Engine RTV Silicone
More informationFuel and exhaust systems 4A 21
Fuel and exhaust systems 4A 21 15.40 Unscrew the union nuts and disconnect the fuel feed and return hoses from the manifold 41 Disconnect the injector wiring harness connector and the vacuum hose from
More information