Operation and Maintenance Manual

Transcription

1 Operation and Maintenance Manual Piston Actuated Air Operated Valve for c1s/c2s/o1s/o2s model operators 10V SW 10SM 20SM 30VM 40VM 60VM 100VM 150V series valves Parker Autoclave Engineers Instrumentation Products Div Hessinger Dr. Erie, PA Tel: Fax: ISO-9001 Certified

2 Table of Contents page 1.0 Installation Spring Adjustment (01S & 02S Valves Only) Packing Adjustment Packing or Stem Replacement Seat Replacement Operator Seal Replacement Service...2 Installation Summary Chart...3 Specification Sheets...3-9

3 Section 1.0 Installation All valves are factory adjusted and tested at the pressure marked on the operator label. Refer to Parker Autoclave Engineers Valves, Fittings and Tubing Catalog (Installation Section) for proper tubing connection installation. The air supply connection on the operator is 1/8 NPT. The recommended value for air pressure at the maximum valve operating pressure is shown on the operator label. The maximum allowable working pressure of the operator is 100 psi. (6.9 bar). An extending stuffing box must be used at temperatures below -100 F (-73 C) or above 800 F (427 C). Refer to Autoclave Engineers Valves, Fittings and Tubing Catalog (Specialty Valves Section) for pressure ratings at various temperatures. Use minimum required air pressure (C1S and C2S operators) or minimum required spring pre-compression (O1S and O2S operators) to increase stem and seat life. See attached Specification Sheets. Applications which require extended cycle life should be considered on an individual basis. caution: For proper operation of air operated valves, the pressure inlet to the valve should always be below the seat. Section 2.0 Spring Adjustment O1S & O2S Valves only On some sizes of the O1S & O2S valves, the spring limits the stem travel at the maximum pressures. This affects the flow capacity of the valve. See attached specification sheets for actual stem travel and flow coefficient. If a longer stem travel is desired when the operating pressure is less than the maximum, then this should be requested at the time of order so that the valve will be properly adjusted at the factory. If a valve has already been set for a higher operating pressure and a longer stem travel is desired, the valve may have to be returned to the factory for stem and packing replacement and refinishing of the seat to assure an effective valve seat seal in the closed position. Section 3.0 Packing Adjustment When the valve packing starts to leak, follow the steps listed below to reseal the valve stem: 1. Relieve all pressure in the valve body. 2. C1S & C2S Valves Only: Relieve all air pressure to the operator inlet. O1S & O2S Valves Only: Apply and maintain air pressure to the operator inlet (so the stem is unseated). 3. Loosen the packing gland locking device. 4. While holding the valve body secure, use a torque wrench to tighten the packing gland to the value shown on the attached Installation Summary Chart. If a torque wrench is not avail able, tighten the packing gland approximately 1/16 turn. 5. Pressurize the valve and check for leaks. 6. If the packing still leaks, relieve all pressure in the valve and repeat steps 4 and 5. If the packing does not seal after several attempts, it probably needs replacement (refer to Section 4.0). 7. Reinstall the packing gland locking device. 8. O1S & O2S Valves Only: Relieve air pressure to the operator. Section 4.0 Packing or Stem Replacement To change the packing or stem, follow the steps listed below: 1. Relieve all pressure from the valve and operator. 2. O1S & O2S Valves Only: Loosen the jam nut on top of the spring housing, then loosen the screw until all spring compression is relieved. Apply air (approximately 20 psi) (1.4 bar) to the operator to move the piston to the open position. 3. Loosen the packing gland locking device. 4. While holding the valve body secure, loosen the packing gland. 1- PARKER autoclave engineers

4 5. Remove the screws holding the valve body to the yoke. 6. Completely loosen the packing gland and remove the valve body. The packing will stay on the stems that have larger stem tip below the packing. 7. If the stem does not have a larger stem tip, go to step #8. For stems that do have a larger stem tip, the stem must be removed from the operator shaft to remove the packing. Loosen the nut on the stem and unscrew the stem. If the stem is difficult to remove, use pliers to grip the portion of the stem inside the yoke. Do not grip the stem below the yoke. This section seals against the packing. 8. Remove the packing from the stem (stems with larger stem tip) or from the valve body (stems without this tip). 9. Place the new packing on the stem or in the valve body. 10. Slide the threaded end of the stem through the packing gland and locking device. Screw the nut back onto the stem and place the locking device on the packing gland. 11. Screw the stem into the shaft until the distance from the stem tip to the yoke equals the dimension shown on the attached Installation Summary Chart. (Piston must be in the open position). Reinstall the position indicator and tighten the stem nut. 12. Place the valve body up to the yoke and hand tighten the packing gland into the valve body. 13. Insert and tighten the body/yoke screws. 14. While holding the valve body secure, tighten the packing gland to the value shown on the attached Installation Summary Chart. 15. Secure the packing gland locking device. Section 5.0 Seat Replacement (Replacement Seat Valves) When the seat requires replacement, use the following procedure: 1. Relieve all pressure from the valve. 2. (O1S and O2S valves only) Loosen the jam nut on top of the spring housing then loosen the screw until all spring compression is relieved. Apply air (approximately 20 psi) to the operator to move the stem to the "open" position. (C1S and C2S valves only) Relieve all pressure to the air operator. 3. While holding the valve body secure, remove the seat retainer or the seat. 4. Inspect the seat for signs of wear or damage. Replaceable seats may be reversed if only one side is worn. If both sides are worn, use a new seat. 5. Place the seat in the body and install the seat retainer. While holding the body secure, torque the seat retainer to the value in the installation summary chart. 6. O1S and O2S valves only. Adjust the spring pre-compression per the specification sheets. Section 6.0 Operator Seal Replacement Consult the factory if seals in the operator require replacement. Section 7.0 Service For Service, contact the Autoclave Engineers Representative in your area, or FAX Autoclave Engineers Support Services at O1S & O2S Valves Only: Tighten the screw on top of the spring housing until the stem bottoms out on the seat (position indicator at C ). Back the screw off, then hand tighten. Tighten the screw the distance shown on the Installation Summary Chart. An equivalent amount of screw revolutions is also given. Once completed, tighten the jam nut securely in place. PARKER autoclave engineers - 2

5 10V2 1/2 (12.7) 15 (20.4) 0.81 (20.6) 0.12 (3.0) /2 (12.7) 10V4 13/16 (20.6) 50 (67.8) 1.12 (28.4) 0.19 (4.8) /16 (20.6) 10V6 13/16 (20.6) 65 (88.4) 1.12 (28.4) 0.12 (3.0) /16 (20.6) Note 5 10V8 13/16 (20.6) 50 (67.8) 1.00 (25.4) 0.25 (6.4) /8 (22.2) SW4 5/8 (15.9) 35 (47.3) 1.19 (30.2) 0.31 (7.9) /16 (14.3) SW6 5/8 (15.9) 50 (67.8) 1.19 (30.2) 0.25 (6.4) /16 (17.5) Note 5 SW8 13/16 (20.6) 65 (88.4) 1.81 (46.0) 0.38 (9.7) /8 (22.2) 10SM9 13/16 (20.6) 80 (108) 1.78 (45.2) 0.56 (14.2) /16 (23.8) 30 (40.7) 10SM12 15/16 (23.8) Note 2 Note (55.6) /16 (30.2) 45 (61.0) 10SM16 1-3/8 (34.9) Note 2 Note (69.9) /8 (34.9) 65 (88.2) 20SM4 5/8 (15.9) 40 (54.8) 1.19 (30.2) 0.56 (14.2) /2 (12.7) 20 (27.1) 20SM6 5/8 (15.9) 40 (54.8) 1.19 (30.2) 0.56 (14.2) /8 (15.9) 30 (40.7) 20SM9 13/16 (20.6) 80 (108) 1.78 (45.2) 0.56 (14.2) /16 (23.8) 55 (74.6) 20SM12 15/16 (23.8) Note 2 Note (55.6) /16 (30.2) 55 (74.6) 20SM16 1-3/8 (34.9) Note 2 Note (69.9) /8 (34.9) 80 (108.5) 30VM4 13/16 (20.6) 60 (81.4) 1.09 (27.7) 0.31 (7.9) /8 (15.9) 25 (33.9) 30VM6 13/16 (20.6) 60 (81.4) 1.09 (27.7) 0.44 (11.2) /16 (20.6) 50 (67.8) 30VM9 13/16 (20.6) 60 (81.4) 1.09 (27.7) 0.44 (11.2) /16 (30.2) 75 (102) 40VM9 13/16 (20.6) 40 (54.8) 1.25 (31.8) 0.50 (12.7) /16 (30.2) 85 (115.3) 60VM4 13/16 (20.6) 60 (81.4) 1.25 (31.8) 0.38 (9.7) /8 (15.9) 25 (33.9) 60VM6 13/16 (20.6) 60 (81.4) 1.25 (31.8) 0.38 (9.7) /16 (20.6) 50 (67.8) 60VM9 13/16 (20.6) 60 (81.4) 1.25 (31.8) 0.50 (12.7) /16 (30.2) 110 (149) 100VM5 15/16 (23.8) 70 (94.9) 1.50 (38.1) 0.56 (14.2) /16 (17.5) 70 (94.9) 150V5 15/16 (23.8) 60 (81.4) 2.31 (58.7) 0.56 (14.2) /16 (17.5) 70 (94.9) Valve Size 10V-2 10V-4 10V-6 10V-8 SW-4 SW-6 SW-8 Operator Type Installation Summary Chart Valve Packing Packing 1 Stem 3 Spring Pre-Compression 4 Tube Gland 6 Tube Gland 1 Size Gland Hex Gland Location O1S and O2S Only Hex Size Torque Size Torque IN. (mm) FT. (Nm) IN. (mm) IN. (mm) Equiv. Seat IN. (mm) FT. (Nm) LBS. Turns on Retainer LBS. Screw Torque 1 Torque may vary ± 10 %. Torque values apply to Teflon* packing. Add 10% for Teflon glass and 25 % for graphite yarn. 2 Fingertight, then 3/4 turn with wrench. (Teflon only) 3 The stem location is the distance from the bottom of the yoke to the tip of the stem (vee stem only) with the piston in the up position. 4 Spring pre-compression required at the maximum working pressure of the valve. 5 Torque wrench not required for AE SpeedBite tube connections. Tighten the gland until the sleeve begins to grip the tubing, then 1-1/4 turns. 6 The 10V2 tube gland hex size was 7/16. Specification Sheet Air To-Close : Series 10V and SW Valves System : ksi (MPa) Air (6.9- (41.4) (55.2) (68.9) (82.7) (96.5) (103.4) 27.6) (0.17) (0.17) (0.17) (0.17) (0.17) (0.17) (0.21) (0.21) (0.21) (0.21) (0.21) (0.24) (0.24) (0.28) (0.21) (0.21) (0.21) (0.24) (0.24) (0.24) (0.28) (0.35) (0.35) (0.38) (0.45) (0.28) (0.28) (0.28) (0.35) (0.38) (0.41) (0.45) (0.35) (0.35) (0.38) (0.48) (0.52) (0.59) (0.62) (0.14) (0.17) (0.21) (0.24) (0.28) (0.31) (0.35) (0.45) (0.48) (0.69) (0.24) (0.24) (0.35) (0.41) NOTE: 1 Cv data is for 2-way straight valves. For angle pattern, add approximately 50% to the Cv value. Max Stem Flow 1 W.P. Travel Coef. psi in cv (MPa) (mm) 15, (103.4) (4.06) 15, (103.4) (4.83) 15, (103.4) (4.83) 10, (68.9) (7.90) 15, (103.4) (6.40) 15, (103.4) (6.40) 8, (58.6) (9.70) 10,000 (68.9) PARKER autoclave engineers - 3

6 Specification Sheet Air to Close: Series 10SM Valve Size Operator Type System KSI (Mpa) ( ) (27.6) (41.4) (55.0) (68.9) (82.7) (96.5) (110.0) (124.0) (138.0) Maximum in (mm) Flow Coefficient 1 10SM , (0.45) (0.45) (0.52) (0.69) (59.3) (9.65) ,000 (0.24) (0.24) (0.28) (0.34) (0.38) (68.9) 10SM-12 Air , (0.62) (0.69) (33.0) (11.18) ,000 (0.31) (0.31) (0.41) (0.55) (0.69) (68.9) 10SM , (0.69) (19.3) (14.22) ,300 (0.41) (0.48) (0.69) (43.4) Air to Close: Series 20SM Valves Valve Size Operator Type System KSI (Mpa) Maximum in (mm) Flow Coefficient ( ) (27.6) (41.4) (55.0) (68.9) (82.7) (96.5) (110.0) (124.0) (138.0) 20SM , (0.28) (0.28) (0.28) (0.28) (0.34) (0.41) (0.48) (0.55) (0.59) (0.66) (137.8) (6.35) (0.14) (0.14) (0.14) (0.14) (0.17) (0.21) (0.24) (0.28) (0.31) (0.34) 20SM , (0.31) (0.31) (0.31) (0.31) (0.38) (0.45) (0.52) (0.59) (0.66) (0.69) (130.9) (6.35) ,000 (0.17) (0.17) (0.17) (0.17) (0.21) (0.24) (0.28) (0.31) (0.34) (0.38) (137.8) 20SM-9 Air , (0.41) (0.41) (0.45) (0.55) (0.69) (73.7) (9.65) ,000 (0.21) (0.21) (0.21) (0.28) (0.34) (0.38) (0.41) (0.48) (0.55) (0.59) (137.8) 20SM , (0.55) (0.55) (0.69) (42.0) (11.18) ,600 (0.28) (0.28) (0.34) (0.41) (0.52) (0.62) (0.69) (93.7) 20SM , (0.69) (0.69) (26.8) (14.22) ,800 (0.34) (0.34) (0.48) (0.69) (60.6) NOTE: 1 Cv data is for 2-way straight valves. For angle pattern, add approximately 50% to the Cv value. NOTE: C1S & O1S - C2S & O2S - PARKER autoclave engineers - 4

7 Air To-Close : Series 40VM Valves Specification Sheet Air To-Close : Series 30VM Valves System : ksi (MPa) Max Stem Flow 1 Valve Operator Type W.P. Travel Coef. Size psi in. Cv (6.9- (82.7) (96.5) (110) (124) (138) (152) (165) (179) (193) (207) (MPa) (mm) 68.9) (0.17) (0.17) (0.17) (0.21) (0.24) (0.24) (0.28) (0.31) (0.34) (0.34) (0.38) 30, VM (207) (4.8) Air (0.10) (0.10) (0.10) (0.10) (0.14) (0.14) (0.14) (0.17) (0.17) (0.17) (0.21) 30VM & (0.21) (0.21) (0.24) (0.28) (0.31) (0.34) (0.38) (0.41) (0.45) (0.48) (0.52) 30, (30VM-6) 30VM (207) (4.8) 0.33 (0.10) (0.10) (0.14) (0.14) (0.17) (0.17) (0.21) (0.21) (0.24) (0.24) (0.28) (30VM-9) System : ksi (MPa) Max Stem Flow 1 Valve Operator Type W.P. Travel Coef. Size psi in. Cv (6.9- (103.4) (137.9) (172.4) (206.9) (241.3) (275.8) (MPa) (mm) 68.9) 40VM-9 Air (0.28) (0.34) (0.41) (0.48) (0.55) (0.62) (0.62) 40, (275.7) (6.35) (0.14) (0.17) (0.21) (0.24) (0.28) (0.31) (0.31) Air To-Close : Series 60VM Valves System : ksi (MPa) Max Stem Flow 1 Valve Operator Type W.P. Travel Coef. Size psi in. Cv (6.9- (172) (207) (241) (276) (310) (345) (379) (414) (MPa) (mm) 138) 60VM-4 & 60VM-6 60VM-9 Air (0.21) (0.21) (0.24) (0.31) (0.34) (0.38) (0.41) (0.48) (0.52) 60, (414) (6.4) (0.10) (0.10) (0.14) (0.17) (0.17) (0.21) (0.21) (0.24) (0.28) (0.24) (0.28) (0.34) (0.38) (0.45) (0.48) (0.52) (0.59) (0.62) 60, (414) (6.4) (0.14) (0.14) (0.17) (0.21) (0.24) (0.24) (0.28) (0.31) (0.31) Air To-Close : Series 100VM Valves System : ksi (MPa) Max Stem Flow 1 Valve Operator Type W.P. Travel Coef. Size psi in. Cv (6.9- (345) (414) (483) (552) (621) (689) (1034) (MPa) (mm) 27.6) 100VM-4 100VM-5 100VM-6 NOTE: 1 Cv data is for 2-way straight valves. For angle pattern, add approximately 50% to the Cv value. PARKER autoclave engineers (60VM-4) 0.09 (60VM-6) ,000 (0.35) (0.38) (0.45) (0.52) (0.59) (0.66) (0.69) (689) Air ,000 (3.0) (0.21) (0.21) (0.24) (0.28) (0.28) (0.31) (0.35) (689) 150VM , (0.24) (0.28) (0.31) (0.31) (0.34) (0.38) (0.41) (0.55) (1034) (3.0)

8 Air To-Open : Series 10V Valves Air To-Open : Series SW Valves Specification Sheet System : ksi (MPa) Max Flow 1 Valve Operator Type W.P. Coef. Size psi Cv ( ) (55.2) (68.9) (82.7) (96.5) (103.4) (MPa) (0.28) (0.28) (0.28) (0.28) (0.28) (0.31) 10V , (3.05) (3.05) (3.05) (3.05) (3.05) (4.06) (103.41) (3.05) (3.05) (3.05) (3.05) (3.05) (3.05) (0.31) (0.31) (0.35) (0.38) (0.41) (0.45) 10V , (3.05) (3.05) (3.65) (4.75) (5.08) (5.59) (103.41) (4.83) (4.83) (4.83) (4.83) (4.83) (4.83) (0.31) (0.31) (0.35) (0.38) (0.41) (0.45) 10V , (3.05) (3.05) (3.65) (4.75) (5.08) (5.59) (103.41) (4.83) (4.83) (4.83) (4.83) (4.83) (4.83) (0.52) (0.59) (0.66) , (6.35) (7.62) (9.65) (68.94) V-8 (6.35) (6.35) (6.35) (0.35) (0.38) (0.41) , (3.56) (5.08) (6.10) (68.94) (6.35) (6.35) (6.35) System : ksi (MPa) Max Flow 1 Valve Operator Type W.P. Coef. Size psi Cv ( ) (55.2) (68.9) (82.7) (96.5) (103.4) (MPa) SW-4 SW-6 SW (0.45) (0.45) (0.52) (0.55) (0.66) (0.66) , (4.83) (4.83) (6.35) (7.87) (9.14) (9.52) (103.41) (6.35) (6.35) (6.35) (6.35) (6.35) (6.35) (0.52) (0.52) (0.66) (0.66) (0.66) (0.69) , (6.35) (6.35) (7.11) (11.17) (13.20) (14.22) (93.07) (6.35) (6.35) (6.35) (4.83) (2.54) (1.52) (0.35) (0.38) (0.41) (0.45) (0.48) (0.52) 15, (103.41) (3.56) (4.38) (6.10) (7.11) (8.64) (9.14) (6.35) (6.35) (6.35) (6.35) (6.35) (6.35) (0.66) (0.66) , (9.52) (7.62) (49.64) (6.35) (1.52) (0.45) (0.52) (0.52) 10, (68.94) (7.11) (9.52) (11.17) (6.35) (6.35) (6.35) NOTE: 1 Cv data is for 2-way straight valves. For angle pattern, add approximately 50% to the Cv value. NOTE: = Spring Pre-compression PARKER autoclave engineers - 6

9 Air to Open: Series 10SM and 20SM Valves Specification Sheet Valve Size 10SM-9 10SM-12 10SM-16 20SM-4 Operator Type System KSI (Mps) ( ) (41.4) (55.2) (68.9) (82.7) (96.5) (110.0) (124.1) (137.9) Maximum Flow Coefficient Cv (0.66) (0.66) (0.66) , to (9.65) (11.18) (14.22) (54.4) (6.35) (4.83) (1.52) (0.38) (0.45) (0.48) (0.52) , to (5.59) (7.11) (8.64) (11.18) (68.9) (6.35) (6.35) (6.35) (4.83) (0.48) (0.52) , to (6.10) (14.22) (48.2) (6.35) (1.52) 75 (0.52) , (14.22) (29.6) 0.06 (1.52) (0.45) (0.45) (0.45) (0.52) (0.59) (0.66) (0.66) (0.66) (0.66) (4.83) (4.83) (4.83) (6.35) (7.87) (9.65) (11.18) (12.70) (14.22) , to (6.35) (6.35) (6.35) (6.35) (6.35) (6.35) (4.83) (3.05) (1.52) (137.8) (0.24) (0.24) (0.24) (0.28) (0.31) (0.34) (0.34) (0.34) (0.34) NOTE: 1 Cv data is for 2-way straight valves. For angle pattern, add approximately 50% to the Cv value. 3 Cv varies because of spring compression limitations. The flow coefficient range is given for the maximum stem travel (lowest system pressure) to minimum stem travel (highest system pressure.) = Spring Pre-compression PARKER autoclave engineers - 7

10 Specification Sheet Air to Open: Series 10SM and 20SM Valves Valve Size 20SM-6 20SM-9 20SM-12 20SM-16 Operator Type System KSI (Mpa) ( ) (41.4) (55.2) (68.9) (82.7) (96.5) (110.0) (124.1) Maximum Flow Coefficient Cv (0.45) (0.45) (0.52) (0.59) (0.66) (0.66) (0.66) (0.66) , to (4.83) (4.83) (6.35) (7.87) (9.65) (11.18) (12.70) (14.22) (125.8) (6.35) (6.35) (6.35) (6.35) (6.35) (4.83) (3.05) (1.52) (0.24) (0.24) (0.28) (0.31) (0.34) (0.34) (0.34) (0.34) (0.59) (0.62) (0.66) (0.66) , to (7.87) (8.64) (11.94) (14.22) (67.5) (6.35) (6.35) (3.81) (1.52) (0.34) (0.38) (0.45) (0.48) (0.52) (0.52) (0.52) , to (4.83) (5.59) (7.11) (8.64) (11.18) (12.70) (14.22) (108.2) (6.35) (6.35) (6.35) (6.35) (4.83) (3.05) (15.24) (0.45) (0.52) (0.52) , to (7.11) (9.65) (14.22) (63.4) (6.35) (6.35) (1.52) (0.52) (0.52) , to.15 3 (9.65) (14.22) (42.0) (6.35) (1.52) NOTE: 1 Cv data is for 2-way straight valves. For angle pattern, add approximately 50% to the Cv value. 3 Cv varies because of spring compression limitations. The flow coefficient range is given for the maximum stem travel (lowest system pressure) to minimum stem travel (highest system pressure.) = Spring Pre-compression PARKER autoclave engineers - 8

11 Specification Sheet Air To-Open : Series 30VM Valves System : ksi (MPa) Max Flow 1 Valve Operator Type W.P. Coef. Size psi Cv (6.9- (82.7) (96.5) (110) (124) (138) (152) (165) (179) (193) (207) (MPa) 103) Single Stage (0.31) (0.31) (0.38) (0.38) (0.38) (0.38) (0.45) (0.45) (0.45) (0.45) (0.52) 30VM (3.0) (3.0) (4.8) (4.8) (4.8) (4.8) (6.4) (6.4) (6.4) (6.4) (7.9) 30, (207) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) 30VM-6 & 30VM-9 Dual Stage (0.17) (0.17) (0.21) (0.21) (0.21) (0.21) (0.24) (0.24) (0.24) (0.24) (0.28) Single Stage (0.31) (0.38) (0.38) (0.45) (0.45) (0.52) (0.52) (0.52) (0.59) (0.59) (0.66) (3.0) (4.8) (4.8) (6.4) (6.4) (7.9) (7.9) (7.9) (9.7) (9.7) (11.2) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) (4.8) Dual Stage (0.17) (0.21) (0.21) (0.24) (0.24) (0.28) (0.28) (0.28) (0.31) (0.31) (0.34) (30VM-9) Air To-Open : Series 40VM Valves System : ksi (MPa) Max Flow 1 Valve Operator Type W.P. Coef. Size psi Cv 1 (6.9- (103.4) (137.9) (172.4) (206.9) (241.3) (275.8) (MPa) 68.9) Dual Stage (0.21) (0.24) (0.28) (0.31) (0.34) (0.34) (0.38) Air To-Open : Series 60VM Valves System : ksi (MPa) Max Flow 1 Valve Operator Type W.P. Coef. Size psi Cv (6.9- (138) (172) (207) (241) (276) (310) (345) (379) (414) (MPa) 103) 60VM-4 & 60VM-6 Single Stage (0.41) (0.48) (0.52) (0.59) (0.66) (0.69) (0.69) ,000 40VM-9 (3.05) (4.57) (6.35) (7.87) (9.65) (10.92) (12.70) (276) (6.35) (6.35) (6.35) (6.35) (6.35) (6.35) (6.35) Single Stage (0.38) (0.45) (0.45) (0.45) (0.52) (0.52) (0.59) (0.59) (0.59) (0.66) (3.0) (4.8) (4.8) (4.8) (6.4) (6.4) (7.9) (7.9) (7.9) (9.7) 60,000 (414) (6.4) (6.4) (6.4) (6.4) (6.4) (6.4) (6.4) (6.4) (6.4) (6.4) Dual Stage (0.21) (0.24) (0.24) (0.24) (0.28) (0.28) (0.31) (0.31) (0.31) (0.34) Single Stage (0.38) (0.45) (0.45) (0.52) (0.52) (0.59) (0.66) (0.66) (0.66) (0.66) 30,000 (207) 0.23 (30VM-6) 0.08 (60VM-4) 0.09 (60VM-6) VM-9 (3.0) (4.8) (4.8) (6.4) (6.4) (7.9) (9.7) (9.7) (11.2) (12.7) 60,000 (414) (6.4) (6.4) (6.4) (6.4) (6.4) (6.4) (6.4) (6.4) (4.8) (3.0) 0.14 Dual Stage (0.21) (0.24) (0.24) (0.28) (0.28) (0.31) (0.34) (0.34) (0.34) (0.34) NOTE: 1 Cv data is for 2-way straight valves. For angle pattern, add approximately 50% to the Cv value. = Spring Pre-compression PARKER autoclave engineers - 9

12 Air To-Open : Series 100VM and 150V Valves Specification Sheet System : ksi (MPa) Max Flow 1 Valve Operator Type W.P. Coef. Size psi Cv (6.9- (276) (414) (552) (621) (689) (862) (1,034) (MPa) 138) 100VM-4 100VM-5 100VM Dual (0.24) (0.28) (0.35) (0.41) (0.48) (0.48) Stage ,000 (3.05) (4.83) (6.35) (7.87) (9.65) (9.65) (689) (3.0) (3.0) (3.0) (3.0) (3.0) (3.0) to V-5 Dual (0.21) (0.28) (0.31) (0.38) (0.41) (0.41) (0.48) (0.52) Stage , (3.0) (4.8) (6.4) (7.9) (9.7) (9.7) (11.2) (14.2) (1034) (3.0) (3.0) (3.0) (3.0) (3.0) (3.0) (3.0) (1.5) NOTE: 1 Cv data is for 2-way straight valves. For angle pattern, add approximately 50% to the Cv value. 3 Cv varies because of spring compression limitations. The flow coefficient range is given for the maximum stem travel (lowest system pressure) to minimum stem travel (highest system pressure). = Spring Pre-Compression. *Teflon is a Registered Trademark of E.I. DuPont de Nemors & Co., Inc. WARNING FAILURE, IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its subsidiaries at any time without notice. Offer of Sale The items described in this document are available for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. Any sale contract entered by Parker will be governed by the provisions stated in Parker's standard terms and conditions of sale (copy available upon request) Parker Hannifin Corporation Autoclave Engineers is a registered trademark of the Parker Hannifin Corporation ME January2014 Instrumentation Products Division Autoclave Engineers Operation 8325 Hessinger Drive Erie, Pennsylvania USA PH: FAX: Parker Hannifin Manufacturing Ltd. Instrumentation Products Division, Europe Industrial Estate Whitemill Wexford, Republic of Ireland PH: FAX: ISO-9001 Certified