High Pressure Gear Pumps & Motors Series PZG Pumps Series MZG Motors
|
|
- Augustine Norman
- 5 years ago
- Views:
Transcription
1 High Pressure Gear Pumps & Motors Series PZG Pumps Series MZG Motors Bulletin 650-Z1
2 High Pressure Gear Pumps and Gear Motors for today s demanding mobile and industrial applications. The PZG and MZG Series of Pumps and Motors are built to run continuously to pressures of up to 3600 PSI. Parker s new series was developed for reliable, high efficiency operation at lower noise levels than previously available. The aluminum front and rear covers are a very dense gravity casting and the center section is a high strength extrusion. This construction allows us to provide a pump and motor that can withstand the most demanding operating conditions and environments. Free moving pressure balanced bushings maintain ideal running clearances, yielding a very high operating efficiency. Volumetric efficiencies are as high as 98%. High capacity DU bushings are standard and provide long life and dependable operation. The result is a pump and motor built to exacting standards for years of trouble free service. Features Very Low Noise Operation. High Operating Pressures Up to: 3600 PSI Continuous and 4000 PSI Intermittent. Rugged Housing Assembly. Special Seal Technology. Very High Efficiencies: Volumetric Efficiency to 98% Mechanical Efficiency to 95% High Tolerance to Contamination. Long Life DU Teflon Lined Bushings. Reversible Motors are Standard. Options Application Information For maximum pump and system life, a fluid cleanliness level of ISO 16/13 is recommended. For ratings on other fluids, such as water glycols and transmission fluid, please consult factory. Intermittent operation is defined as 10% of the duty cycle with a maximum time of 5 seconds per incident. Operating fluid viscosity range is SSU. Maximum start-up viscosity is 4000 SSU. Fluid should have maximum anti-wear properties, rust and oxidation inhibitors. Pump inlet vacuum should not exceed 10 in. Hg. (0.35 bar) at 1800 RPM or 5 in. Hg. (0.17 bar) at pump rated speed. Maximum positive inlet pressure is 10 PSI (0.69 bar). Pump and prime mover shaft alignment must be within inches total indicator reading. For applications with side load conditions, such as belt driven pumps, please contact the Parker. For information not specified in this brochure please contact your nearest Parker Distributor or the. Straight Keyed or Spline Shafts. Buna-N or Viton Seals. 1
3 PSI FLOW (GPM) 7 CC s/rev. PZG1A Instructions: To size a pump 1/ Where RPM intersects displacement read GPM. / Where GPM intersects PSI read HP. Example: An electric motor operating at 175 RPM with a 4.1cc pump would produce a flow of 1.9 GPM. At 3600 PSI this would require a 5 HP electric motor INPUT HORSEPOWER SPEED (RPM) GPM PSI (bar) PSI (bar) RPM DIMENSIONS PZG1A TYPE Operating Intermittent Maximum Inches (mm) Code cc s/rev. (cu.in.) RPM RPM Pressure Pressure Speed L M (0.08) 0.59 (.3) 1.18 (4.47) 3600 (48) 4000 (76) (41.9) 3.3 (8.0) (0.1) 0.91 (3.44) 1.8 (6.89) 3600 (48) 4000 (76) (4.9) 3.31 (84.1) (0.17) 1.3 (4.66).46 (9.31) 3600 (48) 4000 (76) (43.9) 3.39 (86.1) (0.5) 1.87 (7.08) 3.74 (14.16) 3600 (48) 4000 (76) (46.0) 3.54 (89.9) (0.31).3 (8.78) 4.65 (17.60) 3600 (48) 4000 (76) (47.5) 3.66 (93.0) (0.37).78 (10.5) 5.56 (1.05) 3600 (48) 4000 (76) (49.0) 3.78 (96.0) L M SQ. KEY Ø Ø OUTLET PORT: 9/16-18 UNF (SAE-6) O-RING.60 MZG MOTOR DRAIN (BI-ROTATIONAL) SAE-3 80 PSIG MAX INLET PORT: 3/4-16 UNF (SAE-8) O-RING 9 TOOTH SPLINE 0/40 PITCH 30 PRESSURE ANGLE MOTOR PORTS (SAE-8) CLOCKWISE ROTATION SHOWN
4 PSI FLOW (GPM) CC s/rev. 7.9 PZGA Instructions: To size a pump 1/ Where RPM intersects displacement read GPM. / Where GPM intersects PSI read HP Example: An electric motor operating at 175 RPM with a 14.0cc pump would produce a flow of 6.4 GPM. At 3600 PSI this would require a 15 HP electric motor INPUT HORSEPOWER SPEED (RPM) GPM PSI (bar) PSI (bar) RPM DIMENSIONS PZGA TYPE Operating Intermittent Maximum Inches (mm) Code cc s/rev. (cu.in.) RPM RPM Pressure Pressure Speed L M (0.4) 3.19 (1.1) 6.38 (4.) 3600 (48) 4000 (76) (47.5) 3.90 (99.1) (0.6) 4.33 (16.4) 8.66 (3.8) 3600 (48) 4000 (76) (49.5) 4.06 (103.1) (0.7) 5.15 (19.5) (39.0) 3600 (48) 4000 (76) (51.1) 4.17 (105.9) (0.9) 6.38 (4.) 1.76 (48.3) 3600 (48) 4000 (76) (53.1) 4.33 (110.0) (1.1) 8.11 (30.7) 16. (61.4) 3400 (34) 3800 (6) (56.1) 4.57 (116.1) (1.3) 9.48 (35.9) (71.8) 3000 (07) 3400 (34) (58.4) 4.76 (10.9) (1.7) 1.71 (48.1) 600 (179) 3000 (07) (64.0) 5.0 (13.1) 1.6 L M SQ. KEY Ø Ø TOOTH SPLINE 16/3 PITCH 30 PRESSURE ANGLE OUTLET PORT: 7/8-14 UNF (SAE-10) O-RING 3.35 MZG MOTOR DRAIN (BI-ROTATIONAL) SAE-6 80 PSIG MAX INLET PORT: 1 1/16-1 UNF (SAE-1) O-RING MOTORS PORTS (SAE-1) CLOCKWISE ROTATION SHOWN 3
5 PSI FLOW (GPM) 70 CC s/rev. PZG3A Instructions: To size a pump 1/ Where RPM intersects displacement read GPM. / Where GPM intersects PSI read HP. Example: An electric motor operating at 175 RPM with a 39.4cc pump would produce a flow of 17.9 GPM. At 3600 PSI this would require a 45 HP electric motor INPUT HORSEPOWER SPEED (RPM) GPM PSI (bar) PSI (bar) RPM DIMENSIONS PZG3A TYPE 175 Max. Operating Intermittent Maximum Inches (mm) Code cc s/rev. (cu.in.) RPM RPM Pressure Pressure Speed L M 5.5 (1.4) 10.5 (38.8) 0.80 (78.7) 3600 (48) 4000 (76) (65.5) 5.18 (131.5) (1.6) 1.03 (45.5) 0.9 (79.) 3600 (48) 4000 (76) (67.0) 5.9 (134.4) (.1) (58.1) 6.71 (101.1) 3600 (48) 4000 (76) (69.5) 5.49 (139.5) (.4) (68.0) 31. (118.) 3600 (48) 4000 (76) (71.5) 5.65 (143.5) (.6) (73.6) (119.5) 3600 (48) 4000 (76) (73.0) 5.77 (146.5) (3.1) 3.4 (88.6) 38.0 (143.9) 3300 (8) 3700 (55) (76.0) 6.01 (153.5) (3.7) 7.34 (103.5) (168.0) 500 (17) 900 (00) (79.0) 6.4 (158.5) (4.) (10.0) (174.0) 500 (17) 900 (00) (8.5) 6.5 (165.5) (4.7) (133.8) (178.4) 000 (138) 400 (165) (85.0) 6.71 (170.5) (5.3) 39.9 (151.1) 46.8 (175.) 000 (138) 400 (165) (88.0) 6.95 (176.5).5 SQ. KEY 1.61 L M MZG MOTOR DRAIN (BI-ROTATIONAL) SAE-6 80 PSIG MAX Ø OUTLET PORT FLANGE PORTS SIZE 5 THRU 514 = 3/4" SAE FLANGE PORT SIZE 600 THRU 876 = 1" SAE FLANGE PORT O-RING PORTS SIZE 5 THRU 514 = SAE-1 SIZE 600 THRU 876 = SAE Ø MOTOR PORTS EQUAL TO INLET PORT OF THE SELECTED DISPLACEMENT CLOCKWISE ROTATION SHOWN 13 TOOTH 16/3 PITCH 30 PRESSURE INLET PORT ANGLE FLANGE PORT SIZE 5 THRU 514 = 1" SAE FLANGE PORT SIZE 600 THRU 876 = 1 1/4" SAE FLANGE PORT O-RING PORTS SIZE 5 THRU 514 = SAE-16 SIZE 600 THRU 876 = SAE-4 4
6 Ordering Information Product Frame Rotation Displacement Ports Shaft Seals Type Size (cc s/rev x 10) Options Product Type PZG Gear Pump MZG Gear Motor Rotation Code Direction R Right Hand L Left Hand B Both Port Types S SAE Straight Thread F SAE Flange Ports* * Available on 3A only. Seal Type Omit Buna-N V Viton Size 1A SAE AA A SAE A 3A SAE B 1A Frame Size Code Pump Displacement cc s/rev(cu.in./rev) Motor (0.08) 00.0 (0.1) 07.7 (0.17) Yes (0.5) Yes (0.31) (0.37) Yes (0.40) (0.60) Yes (0.70) Yes (0.90) Yes (1.10) Yes (1.30) Yes (1.70) Yes 5.5 (1.40) (1.60) (.10) Yes 3A (.40) A Frame Size Frame (.60) Yes Size (3.10) Yes (3.70) Yes (4.0) (4.70) Yes (5.30) Yes Code Shaft Types Type 1 Straight Keyed 1A = 1/" Dia. A = 5/8" Dia. 3A = 7/8" Dia. Splined 1A = 9 Tooth A = 9 Tooth 3A = 13 Tooth! WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other information from, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users having technical expertise. It is important that you analyze all aspects of your application including consequences of any failure, and review the information concerning the product or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met. The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by and its subsidiaries at any time without notice. Offer of Sale The items described in this document are hereby offered for sale by, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in Catalog on the page entitled Offer of Sale. 5
Super Charged Piston Pumps Variable Displacement For Open Circuits. PAVC Medium Pressure
aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding PAVC Medium Pressure Super Charged Piston Pumps Variable Displacement
More informationGear Pumps / Motors. Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs
Gear Pumps / Motors Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs Contents Contents Page PGP/PGM500 Characteristics... 3 PGP502 Ordering... 4 PGP502 Performance curves... 5
More informationPVX-11 VANE PUMPS. See pages 12 thru 14 for PVX-11 dimensions. VARIABLE DISPLACEMENT, PRESSURE COMPENSATED PERFORMANCE SPECIFICATIONS
PVX-11 VANE PUMPS VARIABLE DISPLACEMENT, COMPENSATED NOTE: See pages thru 14 for PVX-11 dimensions. PERFORMANCE SPECIFICATIONS Displacement (Nominal) 1.5 in 3 /rev. (25 cm 3 /rev.) Displacement (Actual)
More informationHPV-10 AXIAL PISTON PUMPS
SPECIFICATIONS Variable Displacement, Pressure Compensated OVERALL EFFICIENCY EFFICIENCY - % 1 9 8 7 6 bar 34 69 13 138 172 27 241 TYPICAL PERFORMANCE SPECIFICATIONS VOLUMETRIC cu. in./rev. 1.26 DISPLACEMENT
More informationHPV-15 AXIAL PISTON PUMPS
SPECIFICATIONS Variable Displacement, Pressure Compensated OVERALL EFFICIENCY EFFICIENCY - % 1 9 8 7 6 bar 34 69 13 138 172 27 241 TYPICAL PERFORMANCE SPECIFICATIONS VOLUMETRIC cu. in./rev. 2.9 DISPLACEMENT
More informationSuper Charged Piston Pumps Variable Displacement For Open Circuits. PAVC Medium Pressure
aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding PAVC Medium Pressure Super Charged Piston Pumps Variable Displacement
More informationPowrFlow PVX Vane Pumps
PowrFlow PVX Vane Pumps POWRFLOW PVX VANE PUMPS YOUR SOURCE FOR VANE PUMPS FOR THE MOST DEMANDING APPLICATIONS What Makes PowrFlow PVX Vane Pumps Your Best Buy? Continental Hydraulics PowrFlow PVX Vane
More informationHPV-15 AXIAL PISTON PUMPS
SPECIFICATIONS Variable Displacement, Pressure Compensated OVERALL EFFICIENCY EFFICIENCY - % 100 90 80 70 60 bar 0 34 69 103 138 172 207 241 TYPICAL PERFORMANCE SPECIFICATIONS VOLUMETRIC cu. in./rev. 2.09
More informationCatalog PowrFlowTM PVX Vane Pumps
Catalog PowrFlowTM PVX Vane Pumps Your source for vane pumps for the most demanding applications. What Makes PowrFlow PVX Vane Pumps Your Best Buy? Continental Hydraulics PowrFlow PVX Vane Pumps deliver
More information1500 Series. Roller Bearing Gear Pumps and Motors (Bi-Rotational) High Performance Features: Hydreco
Roller Bearing Gear Pumps and Motors (Bi-Rotational) High Performance Features: The 1500K Series Pump/Motor utilizes the many design and application features of the widely accepted HYDRECO Series modern
More informationFlow Control Valves Check Valves Gauge Control Valves. Colorflow Valves
Check Valves Gauge Control Valves Colorflow Valves Colorflow and Ball Valves Industrial Flow Control, Check, Gauge Control Catalog HY14-3300/US Colorflow and Ball Valves Fully guided poppets are used on
More informationFixed Displacement Gear Pumps
Fixed Displacement Gear Pumps D/H/HD Series Introduction Series D/H/HD Features Pressure-loaded design Efficient, simple design - few moving parts Exceptionally compact and lightweight for their capacity
More informationGear Pumps / Motors. Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs
Gear Pumps / Motors Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs Table of contents Heavy-duty Pumps and Motors Series PGP, PGM Contents Page Series 500 Aluminium Table of
More informationHPVR-10 AXIAL PISTON PUMPS
The HPVR series of inline axial piston variable displacement pumps, are available in five displacements and three compact frame sizes. These pumps feature medium-high working pressure capabilities that
More informationSeries PHP10 Variable Volume, Piston Pumps
Catalog HY13-1553-1/N,EU Series PHP1 Series PHP1 Variable Volume, Piston Pumps Bulletin 2-18/US 123 Catalog HY13-1553-1/N,EU Series PHP1 Performance Information Series PHP1 Pressure Compensated, Variable
More informationSnap-tite Quick Disconnect Couplings for Applications Requiring Virtually No Air Inclusion or Spillage
Snap-tite Quick Disconnect Couplings for Applications Requiring Virtually No Air Inclusion or Spillage 8- Series For Pressures to 0 psi ( bar) 9 Series For Pressures to 0 psi ( bar) Featuring: Low pressure
More informationD SERIES HYDRAULIC PUMP
uk distributor for D SERIES HYDRAULIC PUMP quality products for mechanical & fluid power jbj Techniques Limited, www.jbj.co.uk Introduction to Concentric D Series Hydraulic Pumps Concentric offers one
More informationSandwich Valves Series CP
Technical Information General Description. pilot operated check valves are designed for maximum flow rates. The valves are typically used in combination with spool type directional control valves to ensure
More informationHydraulic Motor/Pump. Series F11/F12 Fixed Displacement. parker.com/pmde
Hydraulic Motor/Pump Series F11/F12 Fixed Displacement parker.com/pmde Series F11/F12 Torque (M) M = D x p x η hm 63 [Nm] Conversion factors 1 kg... 2.20 lb 1 N... 0.225 lbf 1 Nm... 0.738 lbf ft 1 bar...14.5
More informationHydraulic Motor/Pump. Series F11/F12 Fixed Displacement. parker.com/pmde
Hydraulic Motor/Pump Series F11/F12 Fixed Displacement parker.com/pmde Series F11/F12 Torque (M) M = D x p x η hm 63 [Nm] Conversion factors 1 kg... 2.20 lb 1 N... 0.225 lbf 1 Nm... 0.738 lbf ft 1 bar...14.5
More informationFEATURES: APPLICATIONS:
Ultimate power and performance in a small package best describes the all new F4 Series gear pumps. The pressure balanced bushing blocks and sleeve bearings provide both extra long life and high performance.
More informationFeatures: Applications: 12 standard sizes Pressures to 3625 PSI (250 Bar)
Ultimate power and performance in a small package best describes the all new F4 Series gear pumps. The pressure balanced bushing blocks and sleeve bearings provide both extra long life and high performance.
More informationMINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM
MINING FORESTRY MOBILE TRUCK AGRICULTURE MATERIAL HANDLING OPTIMUM Muncie Power Products OPTIMUM Series gear pumps/motors offer premier performance for a wide variety of applications across several industries.
More informationWARNING User Responsibility
WARNING User Responsibility FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other
More informationService Manual Series F12
Bulletin HY30-5504-M1/UK Effective: June, 2006 Supersedes: August, 2003 List of contents Page General information...3 Specifications...4 Disassembling...5-10 Assembling...11-16 Change of shaft seal...17
More informationFIXED DISPLACEMENT VANE PUMPS
FIXED DISPLACEMENT VANE PUMPS Single Vane Pumps Double Vane Pumps Thru-Drive Vane Pumps HS - HQ - VH - SERIES Working pressure: up to 210 bar Displacements: from 3 cc to 200 cc Pumps, cartridges and spare
More informationHydraulic Motor/Pump. Series F11/F12 Fixed Displacement
Hydraulic Motor/Pump Series F11/F12 Fixed Displacement Series F11/F12 Torque (M) M = D x p x η hm 63 [Nm] Conversion factors 1 kg... 2.20 lb 1 N... 0.225 lbf 1 Nm... 0.738 lbf ft 1 bar...14.5 psi 1 l...0.264
More informationVickers. Piston Motors. Inline Piston Motors. Fixed and Variable Displacement. Revised 5/99 691
Vickers Piston Motors Inline Piston Motors Fixed and Variable Displacement Revised 5/99 691 Table of Contents Introduction........................................................................................
More informationF SERIES GEAR PUMP. 2 Muncie Power Products, Inc Muncie Power Products, Inc.
ALL NEW DESIGN F SERIES GEAR PUMP ALL NEW DESIGN Ultimate power and performance in a small package best describes the all new F Series gear pumps. Designed exclusively for those low flow applications.
More informationCatalog HY /NA. Catalog HY /NA. Parker Hannifin Corporation Hydraulic Pump Division Marysville, Ohio USA
Catalog HY28-6/NA PV, PVT Series Piston Pumps Variable Volume Catalog HY28-6/NA 1 Catalog HY28-6/NA Notes Series PV 2 Catalog HY28-6/NA Introduction Series PV Quick Reference Data Chart Pump Delivery Approx.
More informationDY Series 1-Piece Ball Valves. Catalog 1001C-A. July 2012 欧陆传动
DY Series 1-Piece Ball Valves Catalog 1001C-A July 2012 欧陆传动 aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Contents
More informationHydraulic Motor/Pump. Series F11/F12 Fixed Displacement. parker.com/pmde
Hydraulic Motor/Pump Series F11/F12 Fixed Displacement parker.com/pmde Series F11/F12 Torque (M) M = D x p x η hm 63 [Nm] Conversion factors 1 kg... 2.20 lb 1 N... 0.225 lbf 1 Nm... 0.738 lbf ft 1 bar...14.5
More informationHydraulic gear pumps and motors
PL 01 T E DISPLACEMENTS From To Hydraulic gear pumps and motors 0.07 in 3 /rev (1.07 cm 3 /rev) 5.56 in 3 /rev (91.10 cm 3 /rev) through bore aluminum body PRESSURE Max. Continuous Max. Intermittent Max.
More informationColorflow and Ball Valves. Industrial Flow Control, Check, Gauge Control. Catalog HY /US
Colorflow and Industrial Flow Control, Check, Gauge Control Catalog HY14-3300/US Colorflow and Fully guided poppets are used on Colorflow valves rather than the less durable ball-check type construction.
More informationHYDRAULIC VARIABLE PUMPS
HYDRAULIC VARIABLE S EFFICIENT VARIABLE DELIVERY Checkball pump delivery is controlled by variable inlet ports in each piston pumping chamber. In these hydraulic variable models, output is regulated by
More informationVane Pumps. VMQ Series Vane Pumps For Industrial and Mobile Applications Displacements to 215 cm 3/ r (13.12 in 3 /r) Pressures to 260 bar (3800 psi)
Vickers Vane Pumps VMQ Series Vane Pumps For Industrial and Mobile Applications Displacements to 215 cm 3/ r (13.12 in 3 /r) Pressures to 260 bar (3800 psi) 5008.00/EN/0596/A A.25 Introduction From the
More informationMagnePump. Recirculation MagnePumps. At a Glance:
MagnePump Recirculation MagnePumps Parker Autoclave Engineers MagnePumps eliminate or reduce many of the problems associated with conventional pumps, such as leakage, contamination and packing heat generation.
More informationVickers. Vane Pumps. Double Thru-drive Vane Pumps. High speed, high pressure VQT Series for mobile equipment. Released 7/93
Vickers Vane Pumps Double Thru-drive Vane Pumps High speed, high pressure VQT Series for mobile equipment Released 7/93 612 Introduction Double VQT high performance pumps are fixed displacement units that
More informationVIKING HG SERIES HELICAL GEAR EXTERNAL GEAR PUMPS
Page 350.1 Series Description Viking s HG series positive displacement pumps are designed to provide low noise transfer and processing of clean, lubricating liquids for applications such as lube oils,
More informationIntroduction Parker are designed for uni-directional flow control of fluids and gases in industries such as chemical processing, oil and gas productio
Check Valves (CO Series) Catalog 4130-CO Revised, June 2001 Introduction Parker are designed for uni-directional flow control of fluids and gases in industries such as chemical processing, oil and gas
More informationVickers 45. VMQ Series 30 Vane Pumps. Fixed Displacement, For Industrial and Mobile Applications (4.188)
[ (4.188) 49,4 (1.94) /21,8 /.86) 174,7/172,3 (6.88/6.78) 332,9/33,5 (13.11/13.1) "M" is marked if metric port threads No marking if inch port threads AS-568-152 O-ring Vickers 45 65,3 (2.57) 13 (5.1 VMQ
More informationNeedle Valves (VQ Series) Catalog 4110-VQ Revised, July 2001
Needle Valves (VQ Series) Catalog 4110-VQ Revised, July 2001 Introduction Parker VQ Series Needle Valves are the right combination of performance and value for manual or pneumatic onoff control in moderate
More informationSolutions. We Manufacture. H y d r a u l i c s. Eaton Medium Duty Piston Pump. h y d r a u l i c s
H y d r a u l i c s ydraulics Eaton Medium Duty Piston Pump h y d r a u l i c s Model 70122, 70422, 70423, and 70523 or -Flow Compensated Piston Pumps We Manufacture April 1997 Solutions S o l u t i o
More informationSeries PVP Variable Volume Piston Pumps
Series PVP Variable Volume Piston Pumps Catalog HY28-2661-CD/US zp2 hpm12-1.p65, lw, jk 1 Notes Series PVP hpm12-1.p65, lw, jk 2 Introduction Series PVP Series Sizes 6-14 Phased Out For Reference Only
More informationDisc Valve Hydraulic Motors 2000 Series
Disc Valve Hydraulic Motors 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Highlights Port A Features Three zone design for longer life and true bi-directionality.
More informationIntroduction Parker are designed for uni-directional flow control of fluids and gases in industries such as chemical processing, oil and gas productio
Check Valves (C Series) Catalog 4130-C Revised, July 2004 Introduction Parker are designed for uni-directional flow control of fluids and gases in industries such as chemical processing, oil and gas production
More informationPiston Pumps Series P2 / P3 Variable Displacement
Piston Pumps Series P2 / P3 Variable Displacement Catalogue HY11-2600/UK July 2003 Contents Series P2/P3 Description Technical information 3 Ordering code 4 Control options LA and LB 6 Control options
More informationIFP HIGH PERFORMANCE INDUSTRIAL SINGLE INTRA-VANE PUMPS
IFP HIGH PERFORMANCE INDUSTRIAL SINGLE INTRA-VANE PUMPS * High Volumetric Efficiency * Maximum 3000 PSI operating pressure * Twelve Vane Design for quite operation * Hydraulic Balanced for external life
More informationwhite drive products SERIES HYDRAULIC MOTORS
white drive products WR SERIES HYDRULIC MOTORS WR overview The WR Series motor incorporates the latest advances for smooth performance, efficiency and durability. It features an optimized Roller Stator
More informationWhisper Pumps VPV Vane Pumps
Whisper Pumps VPV Vane Pumps Contents Whisper Vane Pump Catalog 3 Contents Introduction 4 Benefits 4 Specifications 5 Ordering details 8 Performance characteristics 12 VPV 16 to PSI (21 Bar) 12 VPV 25
More informationDisc Valve Hydraulic Motors 4000 Compact Series
Disc Valve Hydraulic Motors 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Port B Port A Features Shuttle Valve with Back- Pressure Relief Valve Highlights
More informationW1500 SERIES HYDRAULIC PUMP
W1500 SERIES HYDRAULIC PUMP Concentric AB Innovation in Hydraulics PRESSURE (P1) 276 BAR (4000 PSI) (P2) 300 BAR (4400 PSI) SPEED 3300 RPM Min. 500 RPM at 4000 PSI (276 BAR) Continuous EFFICIENCY Overall
More informationOildyne. Miniature Piston Pumps 5 Piston Design. Pressures to 276 bar (4000 psi) Displacements from.156cc/rev to.865cc/rev (.01 to.
Oildyne 5 Piston Design Pressures to 276 bar ( psi) Displacements from.156cc/rev to.865cc/rev (.1 to.5 in 3 /rev) 29 Features Pumping Efficiencies to 9% Allow You to Effectively Use.156 to.865 cc Flow
More informationGM25 Motor Dimensional Information
GM25 Series Birotational Hydraulic Motors GM25 Series hydraulic motors are designed for low noise, high efficiency birotational operation. Cast iron construction insures reliability and strength. A number
More information6000 Series Highlights
Highlights Features 9 displacements available Presents a multitude of options that make this motor very smart and flexible to apply Benefits Very tough motor for demanding applications Can be used in a
More information74 Series ISO Interchange
Series ISO 8 Interchange Featuring Snap-tite quality with superior pressure and flow characteristics over the competition. Flush Face/Dry Break design facilitates easy cleaning prior to connection High
More informationwhite drive products SERIES HYDRAULIC MOTORS
white drive products RS SERIES HYDRULIC MOTORS RS overview RS Series motors are the most economical model in the White Drive Products product line, but are not low-tech. Unlike competitive products using
More informationW SERIES HYDRAULIC MOTORS. WM600 Flange Options
W SRIS HYDRAULIC MOTORS W Series motors are available in 3 families with displacements ranging from.183 in. 3 to 3.05 in. 3 (3 cc to 50 cc). W Series motors are available in both unirotational or birotational
More informationISO Interchange SERIES
ISO 18 Interchange SERIES Series ISO 18 Interchange Featuring Snap-tite quality with superior pressure and flow characteristics over the competition. Flush Face/Dry Break design facilitates easy cleaning
More informationPumps & Motors GRESEN INDEX
Pumps & Motors GRESEN INDEX Series Overview......................156-157 Pump and Motor Displacement Chart...158-159 General Product and Safety Information.....160 Torque Requirements & Overhang Data......161
More informationDisc Valve Hydraulic Motors Series 6000
Disc Valve Hydraulic Motors Series 6000 10.2014 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.2014 EN EATON_Motoren english Highlights Features 9 displacements available Presents a multitude
More informationW1200 SERIES HYDRAULIC PUMP
W1200 SERIES HYDRAULIC PUMP HYDRAULIC SYSTEMS DIVISION Outstanding Hydraulic Products, Service and Expertise, Worldwide 2 Table of Contents Description Page Number W1200 Product Specifications and Performance
More informationCheck Valves (CO Series) Catalog 4130-CO Revised, June 2001
Check Valves (CO Series) Catalog 4130-CO Revised, June 2001 Introduction Parker are designed for uni-directional flow control of fluids and gases in industries such as chemical processing, oil and gas
More informationCheck Valves (C Series) Catalog 4130-C Revised, July 2004
Check Valves (C Series) Catalog 4130-C Revised, July 2004 Introduction Parker C Series Check Valves are designed for uni-directional flow control of fluids and gases in industries such as chemical processing,
More informationGerotor Pump & Motor zgp06
zgp Aluminum High Speed, Low Torque Series Catalog HY9-PGG/MGG/US Catalog HY9-PGG/MGG/US General Information The Parker Hannifin Assures: Consistent quality Technical innovation Premier customer service
More informationMagneDrives. Agitation
MagneDrives Agitation Parker Autoclave Engineers MagneDrive is a magnetically coupled, packless rotary impeller system designed to provide continuous high speed mixing without leakage or contamination.
More informationVane motor high performance hydraulic series M5B - M5BS - M5BF
Vane motor high performance hydraulic series M5B - M5BS - M5BF Publ. 2 - AM172 - B 1 / 25 / FB Replaces : 2 - AM172 - A L11-2172 - 2 CHARACTERISTICS - M5B* SERIES LOW NOISE MOTOR 12 vanes and a patented
More informationPerformance Information Series PVP 100/140 Pressure Compensated, Variable Volume, Piston Pumps
Catalog HY13-155-2/US Technical Information Series PVP 1/14 Performance Information Series PVP 1/14 Compensated, Variable Volume, Piston Pumps Features High Strength Cast-Iron Housing for Reliability and
More information23 SERIES INDUSTRIAL DRY BREAK COUPLINGS. Featuring Snap-tite quality with superior pressure and flow characteristics over the competition
INDUSTRIAL DRY BREAK COUPLINGS SERIES Featuring Snap-tite quality with superior pressure and flow characteristics over the competition Rugged construction High strength steel with Zinc Trivalent Chromate
More informationWARNING User Responsibility
WARNING User Responsibility FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. This document and other
More information6000 Series. Highlights C-5. Description With torque up to 15,000 in-lb and 40 gpm continuous, this motor is packed with power operates very smoothly.
Highlights Features 9 displacements available Presents a multitude of options that make this motor very smart and flexible to apply Benefits Very tough motor for demanding applications Can be used in a
More informationDisc Valve Hydraulic Motors
Disc Valve Hydraulic Motors State of the art motors benefiting from years of experience and inovating constantly to fit your demands. C-i Disc Valve Hydraulic Motors Highlights Product Description In the
More informationRotary Plug Valves (PR Series) Catalog 4126-PR Revised, July 2003
Rotary Plug Valves (PR Series) Catalog 4126-PR Revised, July 2003 PR Series Rotary Plug Valves Introduction Parker PR Series Plug Valves provide positive leak tight shut-off, high flow capacity, and quick
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
SPECIFICATIONS PF1000 Series Fixed Displacement Pumps Also refer to "Checkball Pump Installation and Operating Recommendations" Bulletin PSI.CB (dynexpumpinstallation.pdf) CONTACT INFORMATION USA Headquarters
More informationVANE PUMPS. Output Flow at 1200 r/min at No-Load U.S.GPM Maximum Operating Pressure MPa (PSI) Graphic Symbols.
B VANE PUMPS Pump Type "PVR" Series Single Pumps Graphic Symbols at r/min at No-Load.. PVR PVR PVR PVR Maximum Operating MPa (PSI) () Page Fixed Displacedment "PVRA" Series Single Pumps "PVR" Series Double
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
SPECIFICATIONS Pressure Compensated Checkball Piston Pumps Also refer to "Checkball Pump Installation and Operating Recommendations" Bulletin PSI.CB (dynexpumpinstallation.pdf) CONTACT INFORMATION USA
More informationDisc Valve Hydraulic Motors Series 4000
Disc Valve Hydraulic Motors Series 0 10.20 inspired hydraulics. Änderungen und Druckfehler vorbehalten 10.20 EN EATON_Motoren english Highlights Features 10 displacements, a variety of mounting flanges
More informationRL4 Series Relief Valve Introduction Parker RL4 Relief Valves are designed such that when the upstream pressure exceeds the closing force exerted by t
Relief Valves (RL4 Series) Catalog 411-RL Revised, July 2001 RL4 Series Relief Valve Introduction Parker RL4 Relief Valves are designed such that when the upstream pressure exceeds the closing force exerted
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
SPECIFICATIONS PF3000 Series Fixed Displacement Pumps Also refer to "Checkball Pump Installation and Operating Recommendations" Bulletin PSI.CB (dynexpumpinstallation.pdf) CONTACT INFORMATION USA Headquarters
More informationSC2000 Series Stainless Steel, 500 PSI Check Valves
Sinclair Collins Stainless Steel, 500 PSI Bulletin SC2000-C/USA Climate & Industrial Controls Features & Specifications Features Simple 3-piece design Piston type stem Investment cast 316 stainless steel
More informationSPUR GEAR PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1451 Page 1451.
Page 1451.1 TABLE OF CONTENTS Features & Benefits...2 Typical Applications...2 Port Location Options...2 Model Number Key...3 Standard Materials of Construction...3 Cutaway View & Pump Features...4 Component
More informationPV Series Gearhead Catalog USA
PV Series Gearhead Catalog USA High radial load, in a value alternative The PV Series Planetary Gearhead combines Power and Versatility in an economical package. It comes in a wide range of options including
More information75500MAX Series and 75500MAXM Series
75500MAX Series and 75500MAXM Series Marine Fuel Filter/Water Separators Instruction Part Number 15349 Rev E Racor Turbine Series fuel filter/ water separators protect the precision components of your
More informationMOVICONTROL. Single and Double Fixed Vane Pumps SERIES V10, V20, 25V/VQ, 35V/VQ, 45V/VQ.
Single and Double Fixed Vane Pumps SERIES V10, V20, 25V/VQ, 35V/VQ, 45V/VQ www.movicontrol.com.br V10/V20 Series Features Balanced vane type pumps are excellent for medium- to low-pressure mobile and industrial
More informationBent Axis Piston Motor, Fixed, Bi-directional Series: MFBP...1
Features 40 bent axis piston motor for high power and small overall dimensions Bi-directional rotation Rotation speed up to 8800 rpm Torque up to 840 Nm ( 619 ft-lbs) Side or rear port locations available
More informationVickers. Vane Pumps. Single and Double Vane Pumps. Model Series V10, V20, V2010, and V2020 for Industrial Equipment.
Vickers Vane Pumps Single and Double Vane Pumps Model Series V10, V20, V2010, and V2020 for Industrial Equipment Revised 1/95 698 Introduction Series V10, V20, V2010, and V2020 fixed displacement pumps
More information320R-RAC Series. Gasoline Fuel Filter/Water Separators. Overview: Contact Information: Product Features: Instruction Part Number Rev.
30R-RAC Series Gasoline Fuel Filter/Water Separators Instruction Part Number 37 Rev. D Overview: Racor 30R-RAC series filters are designed for high-performance applications, which means your engine will
More informationPulse Width Modulation Valves. Models SPW-0 thru -7
November 2017 Bulletin / Bulletin 30-30 30-30 Page 1 Pulse Width Modulation s Models SPW-0 thru -7 Page 2 Bulletin 30-30 Pulse Width Modulation s For Refrigerant Flow Control in Direct Expansion HFC, HCFC
More informationBall Valves (B Series) Catalog 4121-B September 1999
Ball Valves (B Series) Catalog 4121-B September 1999 Two-Way B Series Ball Valves Introduction Parker manually, pneumatically, and electrically actuated two-way B Series Ball Valves provide quick 1/4 turn
More informationMotors & Pumps- Hydraulic Pumps, Motors & Power Units
- Hydraulic umps, Motors & ower Units - Rapid Response...12-1 12-6 Hydraulic umps - Check Valves...12-7 Hydraulic umps - ower Units...12-8 12-9 12MOTORS & UMS Hydraulic umps - Vane ump...12-10 Motors...12-11
More informationBall Valves (B Series) Catalog 4121-B Revised, November 2001
Ball Valves (B Series) Catalog 4121-B Revised, November 2001 Two-Way B Series Ball Valves Introduction Parker manually, pneumatically, and electrically actuated two-way B Series Ball Valves provide quick
More informationMobile Piston Pump Series 620
Mobile Piston Pump Series 620 01.2016 inspired hydraulics. Änderungen und Druckfehler vorbehalten 01.2016 EN 620er Pumpe_EN english Mobile Piston Pump Series 620 Introduction 620 Series Piston Pump Eaton
More informationSolutions. ydraulics. We Manufacture. H y d r a u l i c s. Char-Lynn Hydraulic Motors: h y d r a u l i c s
H y d r a u l i c s ydraulics Char-Lynn Hydraulic Motors: http://www.charlynn.com 00--0 h y d r a u l i c s General Purpose Motors We Manufacture No. - October 1 Solutions S o l u t i o n s Features Integrated
More informationMobile Cylinder Div. Standard Build Series. Catalog HY /US Rev C
Mobile Cylinder Div. Standard Build Series Catalog HY18-0014/US Rev C WARNING - USER RESPONSIBILITY FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE
More informationENGINEERING DATA. Quick Reference Chart. Variable Volume Vane Pumps Models SV-20 & SV-25 Flange & Subplate Mounted. Industrial Hydraulics
ENGINEERING DATA Industrial Hydraulics Variable Volume Vane Pumps Models SV-20 & SV-25 Flange & Subplate Mounted SYMBOL Quick Reference Chart GPM @ MAXIMUM PRESSURE THEORETICAL INPUT HP MODEL 100 PSI &
More informationVariable displacement axial piston pumps
Variable displacement axial piston pumps SVP series GENERAL INFORMATIONS Variable displacement axial piston pump swash plate design for open circuit-flow sharing control valve. The pump has been designed
More informationDV-20 DRILLING DRIVE TRULINK TORQUE PIN DRIVES 12T - 20T 20'
DV-20 DRILLING DRIVE VARIABLE SPEED DRIVE UNIT PN 610442 EXCAVATOR SIZE 12T - 20T MAX HOLE DEPTH 20' Removable Top Section CONNECTIONS HEX MAX HOLE DIA. 6' Motor Equipped with Quick Powerful & Efficient
More information611H Flo-Con Pressure Regulators & Valves
aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding 611H Flo-Con Regulators & Valves Catalog F-2, February 2012 Page 2
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI U.S.A. Tel: FAX:
SPECIFICATIONS PF2000 Series Fixed Displacement s Also refer to "Checkball Installation and Operating Recommendations" Bulletin PSI.CB (dynexpumpinstallation.pdf) CONTACT INFORMATION USA Headquarters Dynex/Rivett
More informationRacor 75500FGX Turbine Series fuel
Installation Instructions 75500FGX Fuel Filter Racor 75500FGX Turbine Series fuel filter/water separator assemblies are designed to be installed on the vacuum side of the fuel transfer pump for best efficiency
More information