Important note. Important Note. Telephone: Fax: VAT Registration No.:

Size: px

Start display at page:

Download "Important note. Important Note. Telephone: Fax: VAT Registration No.:"

Beatrix Cross
6 years ago
Views:

1 Telephone: Fax: VAT Registration No.: Important note NOTE: Timing belt check and replacement intervals are subject to change at any time. To ensure that you are using the most up-to-date and accurate information available connect to Autodata Online. Contact your distributor about connecting to Autodata Online. Important Note All service items are vital to the smooth running and reliability of a vehicle, none more so than the timing belt and its associated components. For this reason we have highlighted important information from the manufacturers' service schedules covering the intervals for checks and replacements. Be sure that you make the vehicle owner aware of this information. Industry best practice is to ensure that the vehicle owner is made aware of the importance of replacing the timing belt and its associated components according to the manufacturers' specification. The service history and the use of the vehicle must be considered when deciding the correct course of action. If there is any doubt to the serviceability of the belt and its components, they should be replaced. Timing belt replacement intervals Where possible the recommended intervals have been compiled from vehicle manufacturers' information. In a few instances no recommendation has been made by the manufacturer and the decision to replace the belt must be made from the evidence of a thorough examination of the condition of the existing belt. Apart from the visible condition of the belt, which is explained fully in the General Instructions/Toothed Timing Belts section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement? When was the belt last replaced and was it at the correct mileage? Is the service history of the vehicle known? Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval? Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected? If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due? If the belt does fail, have you considered the consequences? If the engine is an INTERFERENCE type then considerable expensive damage may well be the result. The cost of replacing a belt as part of a routine service could be as little as 5 to 10% of the repair cost following a belt failure. Make sure your customer is aware of the consequences. If in doubt about the condition of the belt - RENEW it. Refer to the Toothed Timing Belts/Service Replacement section for further information relating to arduous or adverse operating conditions, inspection and service replacement. Replacement Interval Guide Replacement Interval Guide Peugeot recommend:

2 307: 05/2007: 06/07-12/07: 2008 : 407: 12/2006: Replacement every 80,000 miles or 10 years under normal conditions. Replacement every 48,000 miles or 10 years under adverse conditions. 01/ /2007: 1,8 06/ /2007: 1,8 01/2008 : Replacement every 75,000 miles or 10 years under adverse conditions. 2,0 06/ /2007: 2,0 01/2008 : 807: 05/2007: 06/ /2007: 01/2008 : The previous use and service history of the vehicle must always be taken into account. Check For Engine Damage Check For Engine Damage CAUTION:This engine has been identified as an INTERFERENCE engine in which the possibility of valve-to-piston damage in the event of a timing belt failure is MOST LIKELY to occur. A compression check of all cylinders should be performed before removing the cylinder head(s). Repair Times - hrs Repair Times - hrs Remove and install 4,10 Special Tools

3 Special Tools Camshaft timing pin - No.(-).0194-B. Flywheel/drive plate locking tool - No.(-).0189-R. Timing belt retaining clip - No.(-).0189-K. Tensioner pulley adjusting tool - No.(-).0189-S Tensioner pulley locking tool - No.(-).0189-S Special Precautions Special Precautions Disconnect battery earth lead. DO NOT turn crankshaft or camshaft when timing belt removed. Remove spark plugs to ease turning engine. Turn engine in normal direction of rotation (unless otherwise stated). DO NOT turn engine via camshaft or other sprockets. Observe all tightening torques. Removal Removal WARNING: Engines with variable valve timing: Mark camshaft sprockets and camshaft adjusters with chalk or paint prior to timing belt removal to assist alignment on installation. Raise and support front of vehicle. RH front wheel. RH wheel arch liner. Engine undershield. Auxiliary drive belt. Unclip pipes from timing belt cover. Support engine. RH engine mounting. Timing belt upper cover [1]. Turn crankshaft clockwise to setting position. Insert flywheel/drive plate locking tool. Tool No.(-).0189-R: [2] : MT. [3] : AT. NOTE: Vehicles with AT: Drive plate locking tool will not fit flush in housing. 307: Reposition PAS pipes adjacent to timing belt lower cover. Insert timing pins in camshaft sprockets [4] & [5]. Tool No.(-).0194-B. Crankshaft pulley bolt [6]. Crankshaft pulley [7]. Timing belt lower cover [8] Slacken tensioner pulley bolt [9]. Turn tensioner pulley clockwise. Use Allen key [10]. Remove timing belt.

4 NOTE: Timing belt must always be renewed once it has been removed. Installation Installation Check tensioner pulley, water pump sprocket and guide pulley for smooth operation. Replace if necessary. Ensure flywheel/drive plate locking tool located correctly [2] or [3]. Ensure timing pins located correctly [4] & [5]. Ensure crankshaft sprocket Woodruff key at 9 o'clock position. Turn tensioner pulley clockwise until pointer [11] passes window [12] in baseplate. Use tool No.(-).0189-S1 [13]. Fit locking tool to tensioner pulley [14]. Tool No.(-).0189-S Remove adjusting tool from tensioner pulley [13]. Fit timing belt to crankshaft sprocket. Secure belt to crankshaft sprocket with retaining clip. Tool No.(-).0189-K [15]. Fit timing belt in following order: Guide pulley. Camshaft sprocket (CA1). Camshaft sprocket (CA2). Water pump sprocket. Tensioner pulley Remove tools [15], [4] & [14]. Fit timing belt lower cover [8]. Fit crankshaft pulley [7]. Clean crankshaft pulley bolt and crankshaft threads. Tighten crankshaft bolt [6]. Tightening torque: 40±4 Nm + 40±4. Turn tensioner pulley anti-clockwise until pointer [16] at position [17]. Use Allen key [10]. Tighten tensioner pulley bolt [9]. Tightening torque: 21±2 Nm. WARNING: Hold tensioner pulley during tightening to prevent it from turning. If tensioner pulley turns when bolt is tightened, repeat tensioning procedure. Remove tools [2] or [3] & [5]. Turn crankshaft 10 turns clockwise to setting position. NOTE: DO NOT allow crankshaft to turn anti-clockwise. Insert flywheel/drive plate locking tool [2] or [3]. Insert timing pin in inlet camshaft sprocket [5]. If timing pin cannot be inserted easily, repeat installation and tensioning procedures. Slacken crankshaft pulley bolt [6]. Slacken tensioner pulley bolt [9] whilst holding Allen key [10]. Turn tensioner pulley clockwise until pointer and notch aligned [16] & [18]. NOTE: If pointer passes notch [18], repeat tensioning procedure. Tighten tensioner pulley bolt to 21±2 Nm [9]. WARNING: Hold tensioner pulley during tightening to prevent it from turning. If tensioner pulley turns when bolt is tightened, repeat tensioning procedure. Fit new crankshaft pulley bolt [6]. Tightening torque: 40±4 Nm + 40±4. Remove tools [2] or [3] & [5]. Turn crankshaft 2 turns clockwise to setting position. NOTE: DO NOT allow crankshaft to turn anti-clockwise. Insert timing pin in inlet camshaft sprocket [5]. Ensure tensioner pulley pointer and notch aligned [16] & [18]. If not, repeat tensioning procedure. Remove timing pin from inlet camshaft sprocket [5]. Install components in reverse order of removal.

Important note. Important Note. Telephone: Fax: VAT Registration No.:

Important note. Important Note. Telephone: Fax: VAT Registration No.: Telephone: Fax: VAT Registration No.: Important note NOTE: Timing belt check and replacement intervals are subject to change at any time. To ensure that you are using the most up-to-date and accurate information