Timing belt replacement intervals
|
|
- Agatha Lane
- 5 years ago
- Views:
Transcription
1 Important note Important note The intervals and procedures given are subject to alteration by the manufacturer at any time. Check the regularly updated Timing Belts section on our website to ensure that you are kept informed of any changes that may occur between issues of the Autodata CD. Timing belt replacement intervals Where possible the recommended intervals have been compiled from vehicle manufacturers' information. In a few instances no recommendation has been made by the manufacturer and the decision to replace the belt must be made from the evidence of a thorough examination of the condition of the existing belt. Apart from the visible condition of the belt, which is explained fully in the General Instructions/Toothed Timing Belts section, there are several other factors which must be considered when checking a timing belt: Is the belt an original or a replacement. When was the belt last replaced and was it at the correct mileage. Is the service history of the vehicle known. Has the vehicle been operated under arduous conditions which might warrant a shorter replacement interval. Is the general condition of other components in the camshaft drive, such as the tensioner, pulleys, and other ancillary components driven by the timing belt, typically the water pump, sound enough to ensure that the life of the replacement belt will not be affected. If the condition of the existing belt appears good, can you be satisfied that the belt will not fail before the next check or service is due. If the belt does fail, have you considered the consequences. If the engine is an INTERFERENCE type then considerable expensive damage may well be the result. The cost of replacing a belt as part of a routine service could be as little as 5 to 10% of the repair cost following a belt failure. Make sure your customer is aware of the consequences. If in doubt about the condition of the belt - RENEW it. Refer to the Toothed Timing Belts/Service Replacement section for further information relating to arduous or adverse operating conditions, inspection and service replacement. Replacement Interval Guide Replacement Interval Guide Volvo recommend: Timing belt: All model years: Check and adjust every 20,000 miles or 2 years. 96/97MY additions: Check at 10,000 miles or 1 year, 50,000 miles or 5 years and 90,000 miles or 9 years. 98MY additions: Check at 10,000 miles or 1 year and 90,000 miles or 9 years. Replacement every 80,000 miles or 8 years (tensioner must also be replaced). Injection pump belt: All model years: Check and adjust every 20,000 miles or 2 years. 96/97MY additions: Check at 10,000 miles or 1 year, 50,000 miles or 5 years and 90,000 miles or 9 years. 98MY additions: Check at 10,000 miles or 1 year and 90,000 miles or 9 years. 98MY: Replacement at 40,000 miles or 4 years, 80,000 miles or 8 years and then every 80,000 miles or 8 years (tensioner must also be replaced). 99MY : Replacement every 80,000 miles or 8 years (tensioner must also be replaced). The previous use and service history of the vehicle must always be taken into account. V
2 Check For Engine Damage Check For Engine Damage CAUTION: This engine has been identified as an INTERFERENCE engine in which the possibility of valve-to-piston damage in the event of a timing belt failure is MOST LIKELY to occur. A compression check of all cylinders should be performed before removing the cylinder head. Repair Times - hrs Repair Times - hrs S/V70 TDI Check and adjust 0,90 Remove and install 2,10 Special Tools Special Tools Camshaft sprocket holding tool - Volvo No Crankshaft pulley locking tool - Volvo No Tensioner pulley spanner - Volvo No Special Precautions Special Precautions Disconnect battery earth lead. DO NOT turn crankshaft or camshaft when timing belt removed. Remove glow plugs to ease turning engine. Turn engine in normal direction of rotation (unless otherwise stated). DO NOT turn engine via camshaft or other sprockets. Observe all tightening torques. Check diesel injection pump timing after belt replacement. Removal - Timing Belt Removal Engine upper cover. Coolant expansion tank. PAS reservoir (if required). Turbocharger air hoses. Auxiliary drive belt and tensioner. Timing belt upper cover [1]. Injection pump belt cover. Raise and support front of vehicle. Splash guard. RH front wheel. V
3 RH wheel arch liner Turn crankshaft to TDC on No.1 cylinder. Ensure timing marks aligned [2] or [3]. Ensure injection pump timing marks aligned [4]. NOTE: If not: Turn crankshaft one turn clockwise. Slacken injection pump locking bolt [5]. Remove keeper plate [6]. Tighten locking bolt to 30 Nm [5]. Hold camshaft sprocket. Use tool No Slacken camshaft sprocket bolt one turn [7]. Loosen camshaft sprocket from taper using a drift through hole in timing belt rear cover. Lock crankshaft pulley. Use tool No NOTE: Ensure crankshaft does not move. Slacken crankshaft pulley centre bolt [8]. Slacken crankshaft pulley bolts [9]. Crankshaft pulley locking tool. Crankshaft pulley bolts [9]. Crankshaft pulley centre bolt [8]. Crankshaft pulley [10]. Timing belt lower cover [11]. Tensioner. Timing belt. Installation - Timing Belt Installation Ensure rear timing belt cover screw is marked with white dot [12]. If not: Remove rear timing belt cover screw [12]. Clean threads. Apply locking compound. Fit screw and tighten. Tightening torque: 10 Nm. Mark screw with white dot. Fit new tensioner pulley. Lightly tighten tensioner pulley bolt [13]. Ensure timing marks aligned [3] & [4]. Ensure injection pump locked in position with bolt [5]. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. NOTE: Ensure engine temperature below 30 C before adjusting timing belt. Slacken tensioner pulley bolt [13]. Adjust belt tension until pointer is 2 mm below fixed mark [14]. Use tool No [15]. NOTE: If distance between pointer and fixed mark is exceeded: Back off tensioner pulley completely and repeat tensioning procedure. Tighten tensioner pulley bolt to 20 Nm [13]. Fit crankshaft pulley. Fit crankshaft pulley bolts [9]. Use new bolts. Fit crankshaft pulley centre bolt. Use new bolt. Lock crankshaft pulley. Use tool No NOTE: Ensure crankshaft does not move. Tighten crankshaft pulley centre bolt. Tightening torque: 160 Nm [8]. Tighten crankshaft pulley bolts. Tightening torque: 20 Nm + 90 [9]. Remove crankshaft pulley locking tool. Tool No Ensure timing marks aligned [2] or [3]. Hold camshaft sprocket. Use tool No Tighten camshaft sprocket bolt according to identification number [7]. Class 8-85 Nm. Class Nm NOTE: Class number identified on bolt head. Slacken injection pump locking bolt [5]. Insert keeper plate [6]. Tighten locking bolt to 12,5 Nm [5]. Turn crankshaft 2 turns clockwise. Ensure timing marks aligned [2], [3] & [4]. V
4 2 2 2 Ensure tensioner pointer 2 mm below fixed mark [14]. If not: Repeat tensioning procedure. Install components in reverse order of removal. Removal - Injection Pump Belt Removal Access timing belt. Remove injection pump belt cover. Turn crankshaft to TDC on No.1 cylinder. Ensure timing marks aligned [2] or [3]. Ensure injection pump timing marks aligned [4]. NOTE: If not: Turn crankshaft one turn clockwise. If timing belt has not been replaced: Check distance between tensioner pointer and fixed mark [16] : If distance exceeds 14 mm: Renew timing belt and tensioner. If distance less than 14 mm: Adjust tensioner until pointer and lower edge of fixed mark aligned [17] & [18]. NOTE: Ensure camshaft sprocket can rotate freely during timing belt adjustment. Slacken injection pump locking bolt [5]. Remove keeper plate [6]. Tighten locking bolt to 30 Nm. Slacken guide pulley nut [19]. Turn guide pulley away from belt. Tensioner. Injection pump belt. Installation - Injection Pump Belt Installation 1 1 Fit new tensioner pulley. Lightly tighten tensioner pulley bolt [20]. Ensure timing marks aligned [2] or [3]. Ensure injection pump timing marks aligned [4]. Ensure injection pump locked in position with bolt [5]. Fit injection pump belt. Ensure belt is taut between sprockets on guide pulley side. Turn guide pulley until pointer aligned with cylinder head flange contour [21]. Use Allen key [22]. Tighten guide pulley nut to 25 Nm [19]. Slacken injection pump locking bolt [5]. Insert keeper plate [6]. Tighten locking bolt to 12,5 Nm [5]. Turn tensioner pulley anti-clockwise until pointers aligned [23]. Use Allen key [24]. NOTE: If floating pointer passes fixed pointer: Back off tensioner pulley completely and repeat tensioning procedure. Tighten tensioner pulley bolt to 20 Nm [20]. Install components in reverse order of removal. V
5 V
Timing belt replacement intervals
Telephone: Fax: VAT Registration No.: Name: 1,8 66kw Manufacturer: Citroen Address: Model: Year: 1998 Registration: Tel - Private: Mileage: Tel - Business: Job number: Tel - Mobile Date Important note
More informationTelephone: Fax: VAT Registration No.: Year: Registration:
Telephone: Fax: VAT Registration No.: Name: Manufacturer: Renault Address: Model: Year: Registration: Tel - Private: Tel - Business: Mileage: Job number: Important note Important note The intervals and
More informationImportant note. Important Note. Telephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Important note NOTE: Timing belt check and replacement intervals are subject to change at any time. To ensure that you are using the most up-to-date and accurate information
More informationImportant note. Important Note. Telephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Important note NOTE: Timing belt check and replacement intervals are subject to change at any time. To ensure that you are using the most up-to-date and accurate information
More informationImportant note. Important Note. Telephone: Fax: VAT Registration No.:
Telephone: Fax: VAT Registration No.: Important note NOTE: Timing belt check and replacement intervals are subject to change at any time. To ensure that you are using the most up-to-date and accurate information
More informationPEUGEOT / 206 CC 1.6i 16V / 09/ /2007 / Cabriolet Country of manufacture EU Cubic capacity/power 1.6 / 80 kw Motor tag RB key PEU 814
1 Vehicle PEUGEOT / 206 CC 1.6i 16V / 09/2000-03/2007 / Cabriolet Country of manufacture EU Cubic capacity/power 1.6 / 80 kw Motor tag NFU RB key PEU 814 Replacement Interval Guide Peugeot recommend: 206:
More informationLAND ROVER GROUP / Freelander I 2.0 Diesel / 09/ /2003 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.
Vehicle LAND ROVER GROUP / Freelander I 2.0 Diesel / 09/1997-09/2003 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.0 / 70-72 kw Motor tag TCie 17N,18N RB key LRG 46 Replacement Interval
More informationVOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ
VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com 1 Accelerator pedal position (APP) sensor - above pedal 2 Brake pedal position (BPP)
More informationLAND ROVER GROUP / Freelander I 2.5 V6 / 09/ /2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.
1 Vehicle LAND ROVER GROUP / Freelander I 2.5 V6 / 09/2001-03/2007 / Terrain vehicle Country of manufacture GB Cubic capacity/power 2.5 / 130 kw Motor tag KV 6 MPI RB key LRG 48 Replacement Interval Guide
More informationMANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE
HONDA 2.2L & 2.3L 4-Cylinder - DOHC & SOHC - 1990-97 MANUFACTURER'S SUGGESTED SCHEDULED MAINTENANCE For 1990-94 vehicles, the manufacturer recommends camshaft and balance shaft belts be replaced at 90,000
More informationALLDATA Online Land Rover Freelander (LN) V6-2.5L - Camshaft Timing Belt
Page 1 of 13 Camshaft Timing Belt Service Repair No - 12.65.18 Remove 1. Disconnect battery earth lead. 2. Remove ancillary drive belt. 3. Remove RH front road wheel. 4. Remove 3 bolts securing RH splash
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationRemoving and installing toothed belt
Page 1 of 10 Special tools and workshop equipment required Diesel injection pump locking pin -3359- (2x) Pin wrench -T10020- Crankshaft stop -T10050- for engines with circular crankshaft sprocket Locking
More informationBMW N12 PSA 1.4 / 1.6 Chain. Engine timing tools. K 10558
Engine timing tools BMW N12 PSA 1.4 / 1.6 Chain K 10558 www.kamasatools.com Plan Layout C A D A B Component Identification Ref OEM Ref BMW OEM Ref PSA Description A 11 9 540 0197-A3 B 11 9 540 0197-A1
More informationFiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan.
Fiat X1/9 1500cc Engine Timing Belt Replacement, Cam Timing and Static Ignition Timing. Photos courtesy of Don Doan. Introduction This document outlines how to replace a timing belt on a Fiat X1/9 1500cc
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT & BALANCE SHAFT BELT
More informationEngine, disassembly and
Page 1 of 13 13-1 Engine, disassembly and assembly Ribbed belt, removing and installing Removing - Remove noise insulation -arrows-. - Remove bumper Repair Manual, Body Exterior, Repair Group 63 - Move
More informationSized for Print. Timing belt, replacing. Special tools: COUNTERHOLD See: Tools and Equipment\ Counterhold
Timing belt, replacing Special tools: 999 5433 COUNTERHOLD See: Tools and Equipment\999 5433 Counterhold Note! Since the illustrations in this service information are used for different model years and/or
More informationReplacing timing belt
"VCC001207 EN 20100809" 1(5) Replacing timing belt Special tools: 998 8500, 999 5456 spark plugs cover two fuel lines clamps lift up expansion tank and place over engine to one side front timing cover
More informationRecommended Installation Procedure (11 DEC 09) ATech Timing Belt Tensioner (979847/901) VW 1.6/2.0L L4 EA189 CR Engine
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to VW s guidelines. The mounting of the TBT is done on the
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationMaster Engine Timing Tool Set
Master Engine Timing Tool Set Ford K 10551 www.kamasatools.com Pack Layout AC V O B C U D M Z S J W W N F Y K/L Q T AD P A H R AB AA E X G I Component identity Part No. OEM Ref Description A 23002-45D
More informationCAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
Installation Engines with ratcheting timing chain tensioners 1. CAUTION: Timing chain procedure must be followed exactly or damage to valves and pistons will result. CAUTION: Do not compress the ratchet
More informationContiTech: Expert Tips for Changing Timing Belts
ContiTech: Expert Tips for Changing Timing Belts Detailed instructions for a CT1015 WP1 and CT1018K1 in an Audi A4 (B6) 2.5-liter V6 TDI with engine code AKE MY 2001 ContiTech shows how to avoid errors
More informationIN-VEHICLE REPAIR. Timing Drive Components. Removal. 3. Disconnect the eight ignition coil electrical connectors.
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components 303-01A-1 Special Tool(s) Compressor, Valve Spring 303-581 (T97T-6565-A) Holding Tool, Crankshaft 303-448 (T93P-6303-A) 3. Disconnect the eight ignition
More informationVOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ
VOLKS CITY BEECH AVENUE CATTEDOWN PLYMOUTH PL4 0QQ Telephone: 01752 667007 Fax: 01752 663399 Email: mail@volkscity.com VAT Registration No.: 133 1580 01 1 Accelerator pedal position (APP) sensor 1/2 -
More informationTIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT
TIMING BELT AND SPROCKET(S) REMOVAL - TIMING BELT 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove right front wheel. 3. Remove belt splash shield. 4. Remove accessory drive belts.
More informationTIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
More informationKD Disassembly/ Assembly recommendations
KD457.48 Disassembly/ Assembly recommendations AUDI: SKODA: VOLKSWAGEN: KD457.48/UK/01-05/2016 A4 (Series 2, 2 FL, Cabriolet), A6 (Series 2, 2FL, Allroad), A8 Superb Passat ENGINES 2.5TDi TIMING BELT DIAGRAM
More information- 1/7 - Copyright Litens Automotive Group All rights reserved.
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationRecommended Installation Procedure Timing Belt Tensioner (979597) 2.0L DOHC, RENAULT F4R Turbo, F4R L DOHC, RENAULT F4P720 (05/18/2004)
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationPART NO. K310. Engine Timing Tools. Renault 3.0 V6 24V.
PART NO. K310 Engine Timing Tools Renault 3.0 V6 24V www.kamasatools.com Plan Layout omponent Identification F Part No Part Number OEM Ref Description Identification A MM 23061-03 M8 x 35 H.T. Setscrew
More informationTiming Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L
Timing Belt: Service and Repair 2002 Acura Truck MDX V6-3.5L Timing Belt Removal Special Tools Required - Holder handle 07JAB-001020A - Holder attachment, 50 mm, offset 07MAB-PY3010A - Socket, 19 mm 07JAA-001020A
More informationAST4830 Diesel Engine Setting/Locking Tool Kit
AST4830 Diesel Engine Setting/Locking Tool Kit Applications: FORD 1.4TDCi, 1.6TDCi, 1.8Di/TDdi/TDCi, 2.0TDCi (Belts). Timing Belt Replacement Applications on DURATORQ diesel engines in FORD Fiesta/Courier
More informationRemoving and installing cylinder head Removing, installing and tensioning toothed belt
Page 1 of 10 Removing and installing cylinder head Removing, installing and tensioning toothed belt Special tools, workshop equipment, test and measuring appliances and auxiliary items required 3359 Locking
More informationPage 1 of 8 2005 Volvo S40 2.4L Eng Base TIMING BELT REPLACEMENT - 2.4L & 2.5L TURBO, 5-CYLINDER REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft
More informationTiming Drive Components Camshaft Timing
SECTION 303-01B: Engine 4.0L SOHC 1998 Explorer/Mountaineer Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/17/2002 Timing Drive Components Camshaft Timing Special Tool(s) Timing Chain Tensioner
More informationRemoving and installing cylinder head
31 30 29 28 27 26 25 24 23 22 1 2 3 11 12 10 4 9 5 6 7 8 Removing and installing cylinder head Checking compression pressure page 15-24. Notes: When installing a replacement cylinder head with a mounted
More informationTiming Belt, Replacing
Page 1 of 8 2004 Volvo XC70 L5-2.5L Turbo VIN 59 B5254T2 Vehicle Level Engine, Cooling and Exhaust Engine Timing Belt Service and Repair Timing Belt, Replacing Timing Belt, Replacing Timing belt, replacing
More informationTIMING BELT TENSIONER FOR AFTERMARKET TENSIONER P/N FORD U.K. 1.8L 4-Cyl. Diesel Revision date: 06/17/1999
1. Failure to set belt tension correctly to this procedure will result in premature engine failure! 2. The Auto-tensioner is a thermal expansion compensation device so tensioning should only be carried
More information1 of 10 2/10/2017 5:20 PM
1 of 10 2/10/2017 5:20 PM Crankshaft Pulley Removal NOTICE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft
More information1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers..
BELT AND SPROCKETS-TIMING REMOVAL TIMING BELT Zoom 1. Disconnect negative battery cable. 2. Remove upper and lower front timing belt covers.. CAUTION: When aligning crankshaft and camshaft timing marks
More informationContiTech: Expert Tips for Changing Timing Belts
ContiTech: Expert Tips for Changing Timing Belts Detailed instructions for CT881K2 / CT881WP1 timing belt kit in a Ford Fiesta V MY 2004 (JH_JD_) 1.4-liter 16 V with engine code FXJA ContiTech shows how
More informationURGENT : Ensure that the precautions relating to safety and cleanliness are adhered to (refer to the brochure: RECOMMENDATIONS - PRECAUTIONS).
PAGE 1 - b1eg1xp0 - removing - refitting timing belt removing - refitting timing belt INJECTION ES9J4S URGENT Ensure that the precautions relating to safety and cleanliness are adhered to (refer to the
More information1999 Honda Accord DX
Installation 1. Clean tensioner pulleys. Ensure cylinder No. 1 is at TDC by aligning dimple on timing belt drive pulley with pointer on oil pump housing. See Fig. 4. Ensure camshaft pulley TDC marks are
More informationRecommended Installation Procedure (31 MARCH 2010) ATech Timing Belt Tensioner (979004) EA T 20 Valve Longitudinal Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationReplacing the timing belt
"VCC116740 EN 20091209" 1(5) Replacing the timing belt Special tools: 999 5433, 999 5456 Removing the timing belt Note! As the illustrations in this service information are used for different model years
More informationIN-VEHICLE REPAIR. Timing Drive Components Camshaft Drive Cassette, LH. Special Tool(s) Holding Tool, Camshaft Sprocket (T97T-6256)
303-01A-1 IN-VEHICLE REPAIR Timing Drive Components Camshaft Drive Cassette, LH 303-01A-1 Special Tool(s) Holding Tool, Camshaft Sprocket 303-564 (T97T-6256) Adapter for 303-564 303-578 (T97T-6256-A) Holding
More informationPART NO. K305. Engine Timing Tools. Ford 1.6 Ti-VCT 1.8 TDi/TDCi 2.0 TDCi.
PART NO. K305 Engine Timing Tools Ford 1.6 Ti-VCT 1.8 TDi/TDCi 2.0 TDCi www.kamasatools.com Plan Layout Component Identification Part No OEM Ref Description Identification A 23054-05 303-748 Crankshaft
More informationValve Clearance Adjustment
2006 Odyssey Valve Clearance Adjustment Report a problem with this article NOTE: Adjust the valves only when the cylinder head temperature is less than 100 ºF (38 ºC). 1. Remove the intake manifold. 2.
More informationAccurate guidelines for longer engine life
VOLKSWAGEN VOLVO Issue 16 2013 VKMC 01270 VKMC 01258-1 VKMC 01258-2 Accurate guidelines for longer engine life Many technicians are taking chances by not following all the manufacturer recommendations
More informationMECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing.
MECHANICAL(H4DOTC DIESEL) > Cylinder Block INSTALLATION 1. After setting the cylinder block to ST, install the crankshaft bearing. ST 499817100 ENGINE STAND Apply a coat of engine oil to the bearing and
More informationTECHNICAL SERVICE BULLETIN
TECHNICAL SERVICE BULLETIN SUBJECT: NO.: 09-15-93 Camshaft Timing Belt Replacement/Adjustment GROUP: Engine Service Procedure DATE: Sep.17, 1993 This Bulletin Is Supplied As Technical Information Only
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal (Standard Tensioner
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT CAUTION: DO NOT turn
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Disconnect negative battery cable. On Millenia, raise and support vehicle. Remove right front wheel. Remove lower engine covers. 2. On all models, remove accessory
More information3/6/2017 Timing Chain Service and Repair, Removal and Replacement: Valve Timing, Installing and Adjusting
Valve timing, adjusting Special tools and equipment - T10068 Camshaft bar - T10069 Counter support - VAG 1331 Torque wrench (5-50 Nm) - VAG 1332 Torque wrench (40-200 Nm) - AMV 174 004 01 Sealing compound
More informationTiming Belt Replacement
2004 Accord Timing Belt Replacement Report a problem with this article NOTE: The following procedure is for the installation of a new timing belt. If you are installing a used belt, refer to the timing
More informationATech Timing Belt Tensioner (979756) PSA EW10A 2.0L Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationRecommended Installation Procedure ATech Timing Belt Tensioner DaimlerChrysler PL, PT, JR 2.0L 4-Cyl. Engine (10/27/2003)
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to DAIMLERCHRYSLER PL s guidelines. The mounting of the TBT
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Raise and
More informationEngine timing tools. Opel DCi Chain Engine. K 10554
Engine timing tools Opel DCi Chain Engine K 10554 www.kamasatools.com Plan Layout G Component Identification Ref A OEM Ref Renault OEM Ref Opel OEM Ref Nissan B MOT 1770 KM 956-1 EN-48334 Description Chain
More information1 of 8 1/17/2017 8:18 AM
Timing Belt Service and Repair, Removal and Replacement: Replacing... http://repair.alldata.com/alldata/article/display.action?componentid=64&... 1 of 8 1/17/2017 8:18 AM Replacing the timing belt Special
More informationInstructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines. Model No: VS4760.V3 1. SAFETY INSTRUCTIONS
Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines Model No: VS4760.V3 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING BELT Removal 1. Disconnect
More informationTiming Belt Removal. CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). 4. Remove the P/S bracket.
Timing Belt Removal CAUTION: Inspect the water pump when replacing the timing belt (page 10-9). Turn the crankshaft so that No. 1 piston is at top dead center (page 6-64). Before removing the timing belt,
More informationReplacing the oil pump / front crankshaft seal
"VCC097797 EN 20100518" 1(5) Replacing the oil pump / front crankshaft seal Special tools: 998 6187, 999 5433, 999 5455, 999 5919, 999 5747, 951 2050 Note! As the illustrations in the information are used
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CAUTION: This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur. TIMING & COUNTERBALANCE SHAFT BELTS
More informationPage 1 of 5 Service Manual: TIMING BELT REPLACEMENT - 3.2L & 3.5L REMOVAL & INSTALLATION 1999 Chrysler 300M 3.5L Eng Question: Is a 3.5 a valve bender? - My Autodata book says every car is bender REMOVAL
More information& MX Loosen the righthand front wheel lug nuts, then raise and support the vehicle with jack stands.
Vehicle: 1996 MAZDA 626: DX 2.0L L4 GAS-FI-N Content: Engine Service >> Timing Belt >> Timing Belt, Replace 1993-97 626 & MX-6 This engine is classified as an Interference engine. If the timing belt breaks
More informationD8 - Distributor. D9 - Auxiliary unit belts
D8 - Distributor l ubricate Lubricate the distributor shaft sparingly (1-2 drops of oil) D9 - Auxiliary unit belts check/adjust Applies to engines which do not have multi-tooth belts Check belt tension.
More informationRecommended Installation Procedure ATech Timing Belt Tensioner and AUDI 2.0L 4V FSI & TFSI Engine (19 January 2015)
The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must be installed
More informationTiming Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: , Removal
2003 Volvo XC90 T6 AWD L6-2.9L Turbo VIN 91 B6294T Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: 999 5433, 999 5456
More informationRECOMMENDET INSTALLATION PROCEDURE Timing Belt Tensioner for Aftermarket OPEL 2.0L SOHC, Fam. 2 (Revision date: 04/27/1999)
1. Allow the engine and tensioner to stabilize to the same relative ambient temperature before installing a tensioner for proper belt tension adjustment. Do not attempt to install a cool tensioner onto
More informationBMW N47 N47S D20A Diesel Engine timing tools. K 10560
Engine timing tools BMW N47 N47S D20A Diesel 1.6 2.0 K 10560 www.kamasatools.com Plan Layout B A D C E Component Descriptions Ref OEM Ref Description A 11 5 320 Flywheel Plate Timing Pin B 11 8 760 Camshaft
More information5. Keep rotating the water pump housing to release the belt tension and remove the belt once it becomes loose.
Initial Preparation: Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to manufacturer s guidelines. Cold Engine Cold tensioner: 1.
More informationService and Repair Note:
Service and Repair Note: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Drive Components - Timing
More information2003 Hyundai Sonata LX
TIMING & COUNTERBALANCE SHAFT BELTS Removal CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate
More informationService and Repair REPLACING TIMING BELT/IDLER PULLEY/BELT TENSIONER. Special Tools:
1 of 9 6/18/2008 8:48 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 1999 Volvo V70 XC AWD L5-2.4L Turbo VIN 56 B5254T Vehicle
More information1 Recommended tools. removing - refitting : timing belt INJECTION ES9J4. PAGE 1 - b1eg1bp0 - removing - refitting : timing belt. - Fig.
PAGE 1 - b1eg1bp0 - removing - refitting timing belt removing - refitting timing belt INJECTION ES9J4 1 Recommended tools - Fig. 1 - [ 1 ] camshaft setting pegs (-).0187 B. - Fig. 2 - PAGE 2 - b1eg1bp0
More informationATech Timing Belt Tensioner (979572) VM MOTORI 2.5L Diesel, Common Rail Engine
Caution: The procedure to access the timing belt tensioner and all other timing driven components must be done according to the car manufacturer s guidelines. Engine temperature: 1. The tensioner must
More informationTiming Belt: Service and Repair Timing Belt Replacement
2003 Saturn Truck VUE V6-3.0L VIN B Copyright 2007, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Timing Belt Replacement Removal Procedure 1. Remove the front timing belt cover. 2. Rotate the crankshaft
More information2003 Cadillac CTS V6-3.2L VIN N
1 of 16 5/11/2013 11:18 AM 2003 Cadillac CTS V6-3.2L VIN N Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair» Timing Belt Replacement Timing Belt Replacement Tools Required
More informationTech Talk. Timing Belt 6VD1/6VE1
Holden DOHC V6 Frontera 6VD1 3.2L 1999 2004 Jackaroo 6VE1 3.5L 1998 2004 Rodeo TF 6VD1 3.2L 1998 2003 Rodeo RA 6VE1 3.5L 2003 2005 Important: Read through all the instructions before proceeding with the
More information2001 Ford FOCUS. Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS. Timing Belt
2001 Ford FOCUS Submodel: ZTS Engine Type: L4 Liters: 2.0 Fuel Delivery: FI Fuel: GAS SECTION 303-01A: Engine??? 2.0L Zetec-E (Zetec) 2001 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date:
More information2003 Land Rover Freelander S. CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed.
FRONT TIMING BELT CAUTION: DO NOT rotate crankshaft or camshafts with timing belt removed and cylinder heads installed. Removal CAUTION: Camshaft timing belt must be replaced if cylinder head is to be
More informationTesting and Inspection. Diagnostic Procedure Step 1-2
1 of 4 5/22/2008 7:54 AM Home Account Contact ALLDATA Log Out Help Select Vehicle New TSBs Technician's Reference Component Search: METRO TOYOTA OK 2002 Nissan-Datsun Altima 2.5 S L4-2.5L (QR25DE) Vehicle
More informationALLDATA Online Ford Focus L4-2.0L DOHC VIN 5 - Service and Repair. Service and Repair
Page 1 of 22 Service and Repair NOTE: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Belt Special
More informationTiming Belt Replacement
Timing Belt Replacement Tools Required Timing Belt Alignment Kit Crank Hub TORX Socket Removal Procedure 1. Disconnect the negative battery cable. 2. Remove the timing belt front cover. 3. Rotate the crankshaft
More informationIMING BELT COMPONENTS REMOVAL
1 of 11 11/21/2012 2:21 PM IMING BELT COMPONENTS REMOVAL 1. Remove the wheel of passenger side. 2. Remove the side cover. 3. Remove the engine cover. 4. Disconnect the power steering hose fixing on the
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION TIMING BELT Removal 1. Noting position for installation reference, disconnect secondary wires from spark plugs. Remove spark plugs. 2. Disconnect negative battery cable. Remove air
More informationPage 1 of 5 21: Drive train, B6284T S80 (-06), 1999, B6284T, 4T65EV-GT, L.H.D 17/3/2013 PRINT 21: Drive train, B6284T Replacing the Special tools: 999 5433 999 5456 Removing the Preparation Caution! the
More informationTIMING BELT REMOVAL - TIMING BELT
2004 Chrysler Concorde V6-3.5L VIN M Vehicle > Engine, Cooling and Exhaust > Engine > Timing Components > Timing Belt > Service and Repair > Procedures TIMING BELT REMOVAL - TIMING BELT CAUTION: The following
More informationDISASSEMBLY. SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System
SORENTO(BL) > 2004 > G 3.5 DOHC > Engine Mechanical System DISASSEMBLY 1. Remove the engine cover. 2. Disconnect the battery negative terminal. 3. Disconnect the radiator lower hose. 4. Disconnect the
More informationChrysler 2.0L DOHC timing belt procedure REMOVAL
Chrysler 2.0L DOHC timing belt procedure REMOVAL CAUTION: Camshaft or crankshaft should not be rotated after timing belt is removed. Damage to valve components may occur. Always align timing marks before
More informationToothed belt, removing and installing
Toothed belt, removing and installing Special Tools and Equipment ^ 3212 spanner wrench ^ 3387 pin wrench ^ T40011 pin ^ T40026 locking pin ^ T40028 socket ^ T40030 camshaft adjuster gauge Removing Lock
More informationTiming Belt: Service and Repair
1996 Honda Accord Sedan L4-2.2L SOHC (16 Valve) Copyright 2009, ALLDATA 9.90 Page 1 Timing Belt: Service and Repair TIMING BELT AND TIMING BALANCER BELT REMOVAL Timing Components NOTE: - Turn the crankshaft
More informationRemoval. All vehicles. Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair. Special Tool(s) Check Pin - Camshaft Pulleys
Published: 11-Mar-2014 Engine - TDV6 2.7L Diesel - Timing Belt In-vehicle Repair Special Tool(s) Check Pin - Camshaft Pulleys 303-1132 Timing Pin - Camshaft Pulleys 303-1126 Timing Pin - Automatic Transmission
More information2002 Mitsubishi Montero Limited
Fig. 9: Removing Drive Belt Auto Tensioner (2001-02 Montero) Sunday, December 07, 2008 2:19:07 2:19:11 PM Page 1 2005 Mitchell Repair Information Company, LLC. Fig. 10: Exploded View Of Timing Belt Components
More informationDisassembly and Assembly
SENR9973-01 September 2007 Disassembly and Assembly 400C Industrial Engine HB (Engine) HD (Engine) HH (Engine) HL (Engine) HM (Engine) HN (Engine) HP (Engine) HR (Engine) Important Safety Information Most
More information