Volkswagen Phaeton 43-2
|
|
- Barnaby Patterson
- 6 years ago
- Views:
Transcription
1 Стр. 1 из 27 Volkswagen Phaeton 43-2 Self-leveling suspension, servicing Troubleshooting of air spring struts and level control system Condition Verification Possible causes Corrective action Very slow loss of pressure vehicle sits crooked after a longer time period Vehicle sits crooked no leakage Vehicle sits too high, cannot be lowered Observe level over longer time period and identify leakage using commercially available leak-detection spray 1) Perform "Guided Fault Finding" using Vehicle Diagnosis, Testing and Information System VAS ) Check if = vehicle has sufficient ground clearance 2.) Check air lines and line routing Leakage at air spring shock absorber Leakage at air lines Leakage at residual pressure retaining valve Vehicle level sensors faulty Linkage or retainer for Level Control System Sensor is bent Vehicle has bottomed out Air line plugged, pinched or frozen Replace air spring strut front 40-3, Air spring strut removing and rear 42-4, Air spring strut, removing and Air line, servicing 43-2, Air line, servicing Replace air spring strut front 40-3, Air spring strut removing and rear 42-4, Air spring strut, removing and Replace Level Control System Sensor 43-2, Selflevelling suspension system, components and installation locations Pinched air lines, servicing, 43-2, Air line, servicing Frozen and plugged air lines, blowing out with compressed air
2 Стр. 2 из 27 3.) Perform "guided fault finding" using vehicle information system VAS 5051 Exhaust valve or air spring valve malfunctioning 4.) Perform steps 1-3, and if no problems are found up to this point, the residual pressure retaining valve is stuck Residual pressure retaining valve stuck Replace air spring strut front 40-3, Air spring strut removing and rear 42-4, Air spring strut, removing and 5.) Perform "guided fault finding" using vehicle information system VAS 5051 Inspection of electrical system relays, harness connectors, wiring and fuses Vehicle sits crooked and can not be raised or can only be raised very slowly 6.) Identify leakages at accumulator with commercially available leak detection spray 7.) Perform "guided fault finding" using vehicle information system VAS 5051 Pressure accumulator leaking Air line or connectors to accumulator leaking Exhaust valve faulty, leaking or open Replace accumulator Air line, servicing 43-2, Air line, servicing Replace air supply unit 43-2, Air supply unit, removing and 8.) Perform steps 5-7, and if no problems are found up to this point, the air supply unit is faulty Air supply unit faulty Replace air supply unit 43-2, Air supply unit, removing and "Quick" pressure loss Vehicle level is uneven, and when attempting to change vehicle level, air escaping from the faulty air spring is audible Air spring faulty Replace air spring strut front 40-3, Air spring strut removing and rear 42-4, Air spring strut, removing and Air line, servicing 43-2, Air line,
3 Стр. 3 из 27 Air line is torn off servicing Insufficient damping Test drive, and adjust the dampening level. The change must be clearly noticeable. Pay attention to "rumbling noises" when driving over uneven roadways. Dampening Adjustment Valve faulty Strut worn Replace air spring strut, front 40-3, Air spring strut removing and rear 42-4, Air spring strut, removing and Replace air spring strut, front 40-3, Air spring strut removing and rear 42-4, Air spring strut, removing and Clean air line system 2) 1) Perform the following test under these conditions: The vehicle must be cold and can not be moved during test Room temperature must be between C and remain constant The vehicle must be sitting on a level surface - Start engine. - Move vehicle with Front Information Display Control Head Control Module J523 to high and then to normal level. - Switch engine off. - Remove connector from Level Control System Control Module J197 to prevent level control from readjusting.
4 Стр. 4 из 27 - Measure vehicle height at all four wheels. - After 24 hours, measure again vehicle height and compare measurement - a - with first measurement. If the vehicle is sitting crooked, a leak is present at suspension with the greatest difference between the first and second measurement. - Check affected air spring strut and corresponding air line using commercially available leak-detection spray in this order: Air line connections Residual pressure retaining valve Check front air spring strut when installed, and check rear air spring struts when removed from vehicle. 2) If an air spring strut is faulty, it may be possible that oil from the strut is leaking into the air supply system. For problemfree operation of the air spring system, it is recommended that the system be cleaned and additional components be replaced after a repair. - Remove affected line from air spring strut and solenoid valve. - Blow line clean with compressed air several times. To do this, direct compressed air to end of solenoid valve line. - Inspect to see if strut oil has leaked into solenoid valve. If strut oil is found in solenoid valve, it must be replaced. - Check internal line from air supply unit to solenoid valve block. If oil is found in internal line, air supply unit must be
5 Стр. 5 из 27 replaced. Self-levelling suspension system, components and installation locations Air supply unit with solenoid valve block Removing and 43-2, Air supply unit, removing and Location: under spare tire well With motor for compressorlevel control system V66 With level control pump temperature sensor G290
6 Стр. 6 из 27 Level control system control module J197 Location: Behind left rear E- Box Removing and 43-2, Level control system control module J197, removing and Reservoir Location: Left rear wheelhouse Left rear level control system sensor G76 Assembly overview 43-2, Left and right rear level control system sensors G76 / G77, removing and Left rear air spring strut With left rear dampening adjustment valve N338 Left rear wheel acceleration sensor G339 Assembly overview 43-2,
7 Стр. 7 из 27 Left and right rear wheel acceleration sensors G339 / G340, removing and Discontinued as of chassis number: 3D4 to Left Front Body Acceleration Sensor G341 Assembly overview 43-2, Left and right Front Body Acceleration Sensor G341 / G342, removing and Left front wheel acceleration sensor G337 Assembly overview 43-2, Left and right front wheel acceleration sensors G337 / G338, removing and Discontinued as of chassis number: 3D4 to Left front air spring shock strut With left front dampening adjustment valve N336 Left Front Level Control System Sensor G78
8 Стр. 8 из 27 Assembly overview 43-2, Left and right front level control system sensors G78 / G289, removing and Right front wheel acceleration sensor G338 Assembly overview 43-2, Left and right front wheel acceleration sensors G337 / G338, removing and Discontinued as of chassis number: 3D4 to Right Front Level Control Sensor G289 Assembly overview 43-2, Left and right front level control system sensors G78 / G289, removing and Right front air spring shock strut With right front dampening adjustment valve N337 Right Front Body Acceleration Sensor G342
9 Стр. 9 из 27 Assembly overview 43-2, Left and right Front Body Acceleration Sensor G341 / G342, removing and Right rear wheel acceleration sensor G340 Assembly overview 43-2, Left and right rear wheel acceleration sensors G339 / G340, removing and Discontinued as of chassis number: 3D4 to Right rear level control system sensor G77 Assembly overview 43-2, Left and right rear level control system sensors G76 / G77, removing and Rear right air spring shock absorber With right rear dampening adjustment valve N339 Rear Body Acceleration Sensor G343
10 Стр. 10 из 27 Assembly overview 43-2, Rear Body Acceleration Sensor G343, removing and Level control system control module J197, removing and Special tools, testers and auxiliary items required Torque wrench V.A.G 1331 Removing - Remove left rear electronic box in luggage compartment Repair Manual, Electrical Equipment, Repair Group 97, Removing and fuse holder, relay carrier, E-boxes and control modules.
11 Стр. 11 из 27 - Unclip connectors - B, C - at control module. - Bend retaining tabs up slightly and remove control module - A - from retainer. Installing Installation is performed in reverse sequence. - Perform basic setting using Vehicle Diagnosis, Testing and Information System VAS Vehicle Diagnosis, Testing and Information System VAS 5051 Left and right front level control system sensors G78 / G289, removing and Assembly overview for level control system sensor G78 / G289 Level control system sensor G78 / G289 Hex socket head bolt, 5 Nm Hex nut, self-locking 8 Nm
12 Стр. 12 из 27 Special tools, testers and auxiliary items required Torque wrench V.A.G 1331 Removing - Raise vehicle. - Disconnect electrical connection. - Remove hex socket head bolts and hex nut while counter holding at studs Installing Installation is in reverse sequence of removal. - Perform basic setting using Vehicle Diagnosis, Testing and Information System VAS Vehicle Diagnosis, Testing and Information System VAS 5051 Left and right front wheel acceleration sensors G337 / G338, removing and Assembly Overview: Left and right front wheel acceleration sensors G337 / G338 Air spring strut
13 Стр. 13 из 27 Hex head bolt, 10 Nm Left and right front wheel acceleration sensors G337 / G338 with retainer Special tools, testers and auxiliary items required Torque wrench V.A.G 1331 Removing - Raise vehicle. - Disconnect electrical connection. - Remove bolts and remove Left and right front wheel acceleration sensors G337 / G338 with retainer. Installing Installation is in reverse sequence of removal. Left and right Front Body Acceleration Sensor G341 / G342, removing and
14 Стр. 14 из 27 Assembly Overview: Left and right Front Body Acceleration Sensor G341 / G342 Front Body Acceleration Sensor G341 / G342 Hex nut, 9 Nm Special tools, testers and auxiliary items required Torque wrench V.A.G 1331 Removing - Raise vehicle. - Disconnect electrical connection. - Remove hex nut and remove Front Body Acceleration Sensor. Installing Installation is in reverse sequence of removal. Left and right rear level control system sensors G76 / G77, removing and Assembly Overview: Left and right rear level control system sensors G76 / G77
15 Стр. 15 из 27 Hex bolt, 10 Nm Hex nut, 10 Nm Rear Level Control System Sensors G76 / G77 Special tools, testers and auxiliary items required Torque wrench V.A.G 1331 Removing - Raise vehicle. - Disconnect electrical connection. - Remove hex bolts and hex nuts - 2 -, remove Front Body Acceleration Sensor. Installing Installation is in reverse sequence of removal. - Perform basic setting using Vehicle Diagnosis, Testing and Information System VAS 5051 Vehicle Diagnosis, Testing and Information System VAS Left and right rear wheel acceleration sensors G339 / G340, removing and
16 Стр. 16 из 27 Assembly Overview: Left and right rear wheel acceleration sensors G339 / G340 Rear air spring strut Hex socket head bolt, 10 Nm Left and right rear wheel acceleration sensors G339 / G340 Special tools, testers and auxiliary items required Torque wrench V.A.G 1331 Removing - Raise vehicle. - Disconnect electrical connection. - Remove hex bolts and remove Left and right rear wheel acceleration sensors G339 / G340. Installing
17 Стр. 17 из 27 Installation is in reverse sequence of removal. Rear Body Acceleration Sensor G343, removing and Assembly Overview: Rear Body Acceleration Sensor G343 Hex nut, 9 Nm Rear Body Acceleration Sensor G343 Special tools, testers and auxiliary items required Torque wrench V.A.G 1331 Removing - Remove right luggage compartment trim Repair Manual, Body Interior, Repair Group 70, Luggage compartment and cargo area trim; Luggage compartment
18 Стр. 18 из 27 trim, removing and on sides. - Disconnect electrical connection. - Remove hex nut and remove Rear Body Acceleration Sensor G343. Installing Installation is in reverse sequence of removal. Air line, servicing Special tools, testers and auxiliary items required Cutting pliers VAS 6228 Faulty air lines do not need to be replaced completely. Partial replacement is possible using a connector. Application air line and connector see Parts Catalog. Note: The repair point must lie within an area protected from water spray, e.g. in interior or between wheel housing liner and wheel housing. The harness connector must be secured to the body with cable ties or a cable guide, and should never be secured to a fuel line or brake line. Select straight line sections for repair area. - Cut air line toward vehicle straight using air hose pliers VAS 6228.
19 Стр. 19 из 27 - Mark - Arrows - end of line in vehicle and on replacement part with a felt-tip pen. Markings serve for checking after repair work is completed. - Route replacement part along original attachment points. - Insert both ends of lines into harness connector until stop. Air line is inserted far enough in connector if first colored mark cannot be seen (the second colored mark remains visible). Air supply unit with solenoid valve block, assembly overview
20 Volkswagen Technical Site: огромный архив документации по автомобилям Volkswagen, Skoda, Seat, Audi Стр. 20 из 27 Air supply unit With motor for compressorlevel control system V66 With level control pump temperature sensor G290 Installed in spare wheel well from vehicle underside Removing and 43-2, Air supply unit, removing and Muffler Spring clamp Intake hose Rubber bushing Air supply unit fasteners
21 Стр. 21 из 27 included in kit Rubber bushing Air supply unit fasteners included in kit Coil spring Air supply unit fasteners included in kit One coil spring is packaged separately and must be installed across from the solenoid valve Metal sleeve Air supply unit fasteners included in kit Bolt 9 Nm Air supply unit fasteners included in kit Air line 5 Nm Observe arrangement of lines at solenoid valve 43-2, Line arrangement on solenoid valve Bolt 10 Nm Solenoid valve block Removing and 43-2, Solenoid valve, removing and Air line 5 Nm
22 Стр. 22 из 27 Between solenoid valve block and air supply unit Air supply unit, removing and Special tools, testers and auxiliary items required Torque wrench V.A.G 1331 Removing - Raise vehicle. - Remove plastic cover below spare wheel well. - Disconnect connectors and Remove air lines - arrows -. - Protect air lines from dirt.
23 Стр. 23 из 27 - Remove hex bolts and remove air supply unit from spare wheel well. Installing Installation is in reverse order of removal, note the following: - Insert air supply unit in spare wheel well. - Install hex bolts and tighten. - Install air lines to solenoid valve - A - and tighten. Tightening torque Plastic cover to spare wheel well Air lines to solenoid valve block Air supply unit to spare wheel well 2 Nm 5 Nm 9 Nm Line arrangement on solenoid valve
24 Стр. 24 из 27 The lines - 1 to 6 - are indicated by color: Blue, right rear air spring strut Green, right front air spring strut Red, left front air spring strut Black, left rear air spring strut Black, (approx. 150 mm long) to compressor Yellow, accumulator - Connect electrical connectors and Check basic setting of self-levelling suspension 43-2, Self-levelling suspension, basic setting. Solenoid valve, removing and Special tools, testers and auxiliary items required
25 Стр. 25 из 27 Torque wrench V.A.G 1331 Removing - Raise vehicle. - Remove plastic cover below spare wheel well. - Disconnect air lines - arrows -. - Protect air lines from dirt. - Disconnect connectors and Remove air line - arrow - from compressor. - Disconnect connector
26 Стр. 26 из 27 - Remove hex bolts and remove solenoid valve - A -. Installing Installation is in reverse order of removal, note the following: - Insert solenoid valve and push in. - Install air lines to solenoid valve - A -. Line arrangement on solenoid valve arrangement on solenoid valve. 43-2, Line Tightening torques Plastic cover to spare wheel well Air lines to solenoid valve block Solenoid valve to air supply unit 2 Nm 5 Nm 10 Nm Self-levelling suspension, basic setting - Check basic setting of self-levelling suspension Vehicle Diagnosis, Testing and Information System VAS Connect Vehicle Diagnosis, Measurement and Information System VAS 5051 and continue switching until "Functions/Component selection" is shown. Then - Press "Suspension, Wheels, Steering". - Press "Level control system". - Press "01 - On Board Diagnostic (OBD) capable systems". - Press "Functions". - Press "Basic setting". The vehicle diagnosis, testing, and information system VAS
27 Стр. 27 из now displays the specified values for the basic setting. - Measure actual ride height of vehicle 43-2, Ride height, measuring. - If you determine a deviation from the specified values, you must input actual value in Level Control System Control Module with help of Vehicle Diagnosis, Measurement and Information System VAS The self-levelling suspension control module "calculates" the entered values and regulates the vehicle to the level for basic setting. Ride height, measuring - Measure ride height vertically from lower edge of fender to center of wheel.
Wheel bearings, assembly overview
Volkswagen Passat B6 - Wheel bearings, assembly overview Стр 1 из 9 40-5 Wheel bearings, assembly overview Suspension strut Multi-point socket head bolt Tip of bolt must point in direction of travel Left
More informationVolkswagen Golf > VW Rabbit GTI 2006-> (A5)
Volkswagen Golf 5 2004-> VW Rabbit GTI 2006-> (A5) A/C Refrigerant System General information Note: General A/C refrigerant system servicing procedures (e.g., component/system descriptions, extracting
More informationVolkswagen Golf > VW Rabbit GTI 2006-> (A5)
Volkswagen Golf 5 2004-> VW Rabbit GTI 2006-> (A5) Allocation of PR. No. for brakes The brake system installed in a vehicle is documented on the vehicle data sticker via the relevant PR number. Example
More informationEngine, removing and installing
Стр 1 из 16 10-1 Engine, removing and installing Special tools, testers and auxiliary items required Torque wrench VAG 1331 Torque wrench VAG 1332 Engine/transmission jack VAG 1383 A Spring type clip pliers
More informationIntake manifold change-over
Page 1 of 10 24-67 Intake manifold change-over This test should only be performed if there is a performance deficiency. The intake manifold switches from the long intake path to the short one at approx.
More informationHeadlamps. Стр. 1 из 34. Headlamps from two different manufacturers may be installed: Hella. Valeo
Volkswagen Passat B6 2005 - Headlamps Стр 1 из 34 94-1 Headlamps General information Headlamps from two different manufacturers may be installed: Hella Valeo With the exception of the various bulb mountings,
More informationEVAP system, servicing
Page 1 of 65 20-130 EVAP system, servicing EVAP system components 1 - Cap nut 10 Nm 2 - Cover 3 - Stud For EVAP canister 15 Nm 4 - Sealing piece 5 - Bleed line To EVAP canister purge regulator valve -
More informationFuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine)
Page 1 of 49 20-6 Fuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine) Note: VAG1921 spring clamp pliers are recommended for installation Always replace
More informationSuspension strut, removing and installing
Page 1 of 16 40-39 Suspension strut, removing and installing Removing - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit to remove trim cap. - Remove wheels. - Remove rubber grommets
More informationSuspension strut, removing and installing
Page 1 of 18 42-24 Suspension strut, removing and installing Removing Vehicle must be standing on its wheels above vehicle lift - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit
More informationTouring Suspension Installation Guide
Touring Suspension Installation Guide Application Guide Description C7 A6 / A7 Touring Suspension Kit Part Number SE701-P60-01 Special Tools Required Qty Description Part Number 1 Torque Wrench VAG 1331
More informationEngine, disassembling and
Page 1 of 38 13-1 Engine, disassembling and assembling Lock carrier, moving into service position Special tools and equipment 3369 support tool 1 - Bolts 2 - Bolts 3 - Bolts 4 - Bolts 5 - Bore 45 Nm (33
More informationOxygen sensor control,
Page 1 of 46 24-71 Oxygen sensor control, checking Oxygen sensor and oxygen sensor control before catalytic converter, checking Special Tools and Equipment VAG1526A VAG1594A VAG1598/31 VAS5051 with VAG5051/1
More informationSTaSIS Engineering B6 B7 Streetsport Suspension
STaSIS Engineering B6 B7 Streetsport Suspension SS Suspension Kit Parts List Qty Description Part Number 1 STaSIS adjusted Koni cadmium plated dampers (2 front, 2 rear) 1150-5061 Special Tools Required
More informationSecondary air system. Secondary air system, function/components
Page 1 of 26 26-41 Secondary air system Secondary air system, function/components The secondary air system permits faster warm-up and thus makes the catalytic converter ready for operation sooner after
More informationTurbocharger system. Note: Observe rules of cleanliness Page Charge air pressure control connection diagram Page 21-2.
Page 1 of 50 21-1 Turbocharger system Note: Observe rules of cleanliness Page 21-22. Charge air pressure control connection diagram Page 21-2. All hose connections are secured with hose clamps: parts catalog.
More informationInstrument cluster. Стр. 1 из 9. The following components are integrated in the instrument cluster: Instrument Cluster Control Module J285
Volkswagen Passat B6 2005 - Instrument cluster Стр. 1 из 9 90-1 Instrument cluster General information The following components are integrated in the instrument cluster: Instrument Cluster Control Module
More informationVolkswagen New Beetle Brake System ABS, ABS/EDL 45 Anti-lock Brake System (ABS) (Page GR-45)
45 Anti-lock Brake System (ABS) (Page GR-45) Anti-lock brake system (ABS) and anti-lock brake system with electronic differential lock (ABS/EDL) ITT Mark 20 IE Differences between ABS ITT Mark 20 IE and
More informationA6 Suspension, Touring
A6 Suspension, Touring Suspension Kit Parts List Qty Description 1 Stasis Performance Spring Kit Special Tools Required Qty Description Part Number 1 Torque Wrench VAG 1331 1 Torque Wrench VAG 1332 1 Engine/transmission
More informationAirbags, servicing. Airbag system, safety precautions WARNING!
Page 1 of 75 69-40 Airbags, servicing Airbag system, safety precautions Checking, removing, installing and servicing may ONLY be performed by qualified personnel. Never perform tests using a test light
More informationChecking lambda control Checking lambda probe and lambda control upstream of catalytic converter
Стр. 1 из 9 Checking lambda control Checking lambda probe and lambda control upstream of catalytic converter Special tools and workshop equipment required V.A.G 1526 A V.A.G 1594 A V.A.G 1598/31 VAS 5051
More informationOxygen sensor control,
Page 1 of 37 24-71 Oxygen sensor control, checking Oxygen sensor and oxygen sensor control before catalytic converter, checking Special tools and equipment - or VAG1526A VAG1594A VAG1598/31 VAS5051 with
More informationRemoving and installing the dash panel
Стр. 1 из 6 Removing and installing the dash panel Removing: WARNING Disconnect battery earth strap Electrical System Rep. Gr.27. Removing the centre console Chapter. Remove the steering wheel Chapter.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS [1] Description: Tow Hitch Wire Harness Kit [2] Application: Nissan Rogue Note: Tow Harness application is limited to specific vehicle option packages that include tow harness
More information1 of 2 5/25/17, 4:57 PM
1 of 2 5/25/17, 4:57 PM Overview - Bumper Cover, Audi Q5 S-Line and Audi SQ5 If the vehicle has lane change assistance, the lane change assistance control module (J769) / (J770) must be recalibrated. 1
More informationFront bumper (Audi RS6)
63-1 Front bumper (Audi RS6) Assembly overview 1 - Air inlet grille To remove pull grille forward 2 - Air inlet grille To remove pull grille forward 3 - Screw 2.5 Nm 3x 4 - Bumper cover Together with impact
More informationFuel injection system, servicing
24-1 Fuel injection system, servicing Component locations overview 1 - Oxygen sensor 1 before Three Way Catalyst G39 2 - Oxygen sensor 2 after Three Way Catalyst G130 3 - Engine Coolant Temperature sensor
More informationPage 1 of 29 Section 04-05: Suspension, Computer Controlled 1997 Town Car Workshop Manual DIAGNOSIS AND TESTING Procedure revision date: 05/16/2000 Suspension, Computer Controlled Inspection and Verification
More information2006 Volkswagen Phaeton
27 - Vacuum hose Insert into brake booster unit Fig. 22: Connection Of Brake Lines From Dual Master Brake Cylinder To Hydraulic Unit Connection of brake lines from dual master brake cylinder to hydraulic
More informationMotronic injection system,
Page 1 of 78 24-1 Motronic injection system, servicing Safety precautions If special testing equipment is required during road test, note the following: WARNING! Scan tools and testing devices must always
More informationINSTALLATION AND USER MANUAL
INSTALLATION AND USER MANUAL SDKIT-730 & SDKIT-734 100% Bolt-On 150 PSI Train Horn System for 2011-2015 F-250 & F-350 Super Duty P/N SDKIT-730 P/N SDKIT-734 Thank you for purchasing a Kleinn Air Horns
More information57-1. Front door. Tools. Special tools and equipment. T Socket 3320/2 Bit insert for Socket T Assembly tool
57-1 Front door Tools Special tools and equipment T 10011 Socket 3320/2 Bit insert for 3320 3410 Socket T 10034 Assembly tool 57-2 Front door, assembly overview Note: The instrument panel must be removed
More information3.6.1 Brake Lamp Switch
2002 TT/TTS Coupe/Roadster Report a problem with this article The ESP road test ascertains the plausibility of the signals transmitted from sender 1 for brake booster -1- -G201-, sensor -2- for brake pressure
More informationWEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
More informationGROUP 33A 33A-1 CONTENTS GENERAL DESCRIPTION... 33A-2 FRONT SUSPENSION DIAGNOSIS. 33A-3 LOWER ARM... 33A-13 SPECIAL TOOLS... 33A-5
33A-1 GROUP 33A CONTENTS GENERAL DESCRIPTION 33A-2 DIAGNOSIS 33A-3 INTRODUCTION TO FRONT SUSPENSION DIAGNOSIS 33A-3 DIAGNOSIS TROUBLESHOOTING STRATEGY 33A-3 SYMPTOM CHART 33A-3 SYMPTOM PROCEDURES 33A-3
More informationFRONT SUSPENSION GROUP 33A 33A-1 CONTENTS GENERAL DESCRIPTION... 33A-2 FRONT SUSPENSION DIAGNOSIS. 33A-3 LOWER ARM... 33A-13 SPECIAL TOOLS...
33A-1 GROUP 33A FRONT SUSPENSION CONTENTS GENERAL DESCRIPTION......... 33A-2 DIAGNOSIS. 33A-3 INTRODUCTION TO DIAGNOSIS........................ 33A-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 33A-3 SYMPTOM
More informationProduct Update Circular
IMPORTANT INFORMATION Please inform and provide a copy of this document to every person in your dealership with campaign-related responsibilities, including Service, Parts and Accounting personnel. By
More informationServicing front brakes
46-1 Servicing front brakes C54 brake caliper, servicing Special tools and workshop equipment required VAG 1331 Torque wrench (or equivalent) VAG 1410 Torque wrench (or equivalent) VAG 1869/2 Brake pedal
More informationThis chapter contains operational verification, adjustment, and repair/replacement procedures for major
V. MAJOR SYSTEMS REPAIR This chapter contains operational verification, adjustment, and repair/replacement procedures for major systems of the RICON. Each section also provides a brief functional description
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM ASSEMBLY REAR SUSPENSION DIAGNOSIS
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION......... 34-2 DIAGNOSIS.. 34-3 INTRODUCTION TO DIAGNOSIS........................ 34-3 DIAGNOSIS TROUBLESHOOTING STRATEGY...... 34-3 SYMPTOM CHART...................
More informationVolkswagen > New Beetle, New Beetle Convertible > Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking
Page 1 of 9 Volkswagen > New Beetle, New Beetle Convertible > 1998-2008 2.0 Liter 4-Cyl. 2V Generic Scan Tool, Engine Code(s): AEG 24 - Components, Checking. Throttle Valve Control Module J338, Checking
More informationItems Vehicles with 4G63 engine Vehicles with 4D56 engine. Type 4-speed full automatic 4-speed full automatic. 2nd rd
23-2 AUTOMATIC TRANSMISSION General Information/ Service Specifications GENERAL INFORMATION 23100010141 Items Vehicles with 4G63 engine Vehicles with 4D56 engine Transmission model R4AW2-6 V4AW2-6 Type
More informationPart # C-10 Level 1 Air Suspension System
350 S. St. Charles St. Jasper, In. 47546 Part # 11330199 63-72 C-10 Level 1 Air Suspension System Front Components: 1 11331099 Front CoolRide Kit for Stock Lower Arms 1 11330509 RQ Series Front Shock Kit
More informationVolkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 13 Engine-Crankshaft, Cylinder block (Page GR-13)
13 Engine-Crankshaft, Cylinder block (Page GR-13) Engine, disassembly and assembly 10-222 A/21 guide from 10-222 A support tool, modifying Ribbed belt, removing and installing Semi-automatic toothed belt
More information00 - GENERAL, TECHNICAL DATA
00 - GENERAL, TECHNICAL DATA BRAKES Brake System APPLICATION OF PR. NO. FOR BRAKES Application of PR. No. for brakes The brake system installed in a vehicle is documented on the vehicle data sticker via
More informationVolkswagen New Beetle Body - Exterior 64 Glass, Window regulators (Page GR-64)
64 Glass, Window regulators (Page GR-64) Flush bonded windows Body flange, preparing for glass installation Broken rear window, removing Cleaning off excess adhesive material Curing time Installation instructions
More information2.8 Liter VR6 2V Fuel Injection & Ignition, Engine Code(s): AAA m.y
2.8 Liter VR6 2V Fuel Injection & Ignition, Engine Code(s): AAA m.y. 1996-1997 01 - On Board Diagnostic (OBD) On Board Diagnostic (OBD II) Malfunction Indicator Lamp (MIL) On Board Diagnostic (OBD II),
More information00 02 Apr. 24, Service
Subject: Model(s): Driver s Side Airbag, On Board Diagnostic (OBD) All 2000 Group: Number: Date: 01 00 02 Apr. 24, 2000 Supersedes T.B. group 01 number 99 20 dated Dec. 8, 1999 Black revision bars indicate
More informationAir Filter Element, Replacing and Cleaning Housing
Air Filter Element, Replacing and Cleaning Housing Note Only use silicone-free lubricant for assembling the intake hoses. Secure all hose connections with hose clamps that match current standard production.
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION TRAILING ARM REAR SUSPENSION DIAGNOSIS TOE CONTROL ARM...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION 34-2 DIAGNOSIS 34-3 INTRODUCTION TO DIAGNOSIS 34-3 DIAGNOSTIC TROUBLESHOOTING STRATEGY 34-3 SYMPTOM CHART 34-3 SYMPTOM PROCEDURES 34-3 SPECIAL TOOLS 34-5 ON-VEHICLE
More informationBefore disconnecting battery Ground (GND) strap obtain security code for radio with antitheft
Page 1 of 14 Volkswagen > New Beetle > 1998-2005 Body Interior 70 - Interior trim Instrument panel, removing and installing WARNING! Disconnect battery Ground (GND) strap before working on electrical system,
More informationVibration damper control
Vibration damper control The damper control system registers the condition of the road surface and the movements of the vehicle via four wheel acceleration sensors and three body acceleration sensors.
More informationCooling system components, removing and installing
19-1 Cooling system components, removing and installing Note: When the engine is warm the cooling system is under pressure. If necessary release pressure before starting repair work. Hoses are secured
More informationAudi A6 Current Flow Diagram No. 14 / 1 Edition
Стр. 1 из 7 Audi A6 Current Flow Diagram No. 14 / 1 Edition 01.1998 Anti-lock brake system (ABS) with electronic differential lock (EDL), traction control system (ASR/TCS) and electronic stability program
More informationThe steering column is only available as a complete unit, without steering lock housing, as a replacement part.
Page 1 of 17 Volkswagen > New Beetle > 1998-2005 Suspension, wheels, steering 48 - Steering column Steering column, removing and installing Special tools, testers and auxiliary items required Torque wrench
More information8.1 4MATIC Contents. b Diagnostic Manual Chassis and Drivetrain 03/ MATIC C/ Model 124.2
8.1 4MATIC Contents 8.1 Model 124.2 Page Diagnosis Function Test................................... 11/1 Diagnostic Trouble Code (DTC) Memory................ 12/1 Complaint Related Diagnostic Chart...................
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION ON-VEHICLE SERVICE FASTENER TIGHTENING SPECIFICATIONS...
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 FASTENER TIGHTENING SPECIFICATIONS 33-2 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 LUBRICANTS 33-3 DIAGNOSIS 33-4 INTRODUCTION
More informationWelding and straightening operations are not permitted on load-bearing or wheelcontrolling
Page 1 of 9 Volkswagen > Passat > 1998-2005 Suspension, Wheels, Steering 40 - Front Suspension. Note: If a vehicle that has a drive axle removed is to be moved, an outer CV joint must be installed in place
More information1 of 2 5/17/17, 1:22 PM
1 of 2 5/17/17, 1:22 PM Trim Molding, Removing and Installing Special tools, testers and auxiliary items required Wedge Set (T10383) Removal Wedge (T40233) Removing - Starting at the front, pry the trim
More informationREAR SUSPENSION GROUP CONTENTS GENERAL DESCRIPTION REAR SUSPENSION DIAGNOSIS LOWER ARM AND TOE CONTROL ARM ASSEMBLY...
34-1 GROUP 34 CONTENTS GENERAL DESCRIPTION........... 34-2 DIAGNOSIS.... 34-2 INTRODUCTION....................... 34-2 TROUBLESHOOTING STRATEGY........ 34-2 SYMPTOM CHART..................... 34-3 SYMPTOM
More information1. General Description
General Description 1. General Description A: SPECIFICATION Front Rear Model Wheel arch height (Tolerance: +12 mm 24 mm ( +0.47 in 0.94 in)) mm (in) 376 (14.8) Camber (Tolerance: 0 45 Differences between
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
XJ SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 7 page REAR SUSPENSION... 16 ALIGNMENT TABLE OF CONTENTS page AND WHEEL ALIGNMENT...1 DIAGNOSIS AND TESTING SUSPENSION
More information.&. Warning! Danger of fire and injury. > Observe general safety regulations for work on the fuel system. > Wear protective gloves and goggles.
Technical Information Incorrect Fuel level Display In Instrument Cluster 1/04 2066 Binder-2, Fuel,Exhaust,EngineElee. Vehicle Type: Model Year: Concerns: Information: 911 Carrera (996) As of '02 {2} After
More informationFAX
INSTALLATION INSTRUCTIONS 6090 Air Suspension Kit (pat. pending) 1999-2006 Tahoe, Suburban, Avalanche, Yukon Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationLubrication system components, removing and installing
17-1 Lubrication system components, removing and installing Note: If large quantities of metal particles or other deposits (caused, for example, by partial seizure of the crankshaft or conrod bearings)
More informationOil pan, oil strainer and valve body, removing and installing
Page 1 of 44 38-1 Oil pan, oil strainer and valve body, removing and installing WARNING! Do not run engine with the oil pan removed or without ATF filling and do not tow vehicle. Notes: Always replace
More informationREAR SUSPENSION GROUP CONTENTS GENERAL INFORMATION FASTENER TIGHTENING SPECIFICATIONS TRAILING ARM...
34-1 GROUP 34 CONTENTS GENERAL INFORMATION 34-2 FASTENER TIGHTENING SPECIFICATIONS 34-4 GENERAL SPECIFICATIONS 34-4 SERVICE SPECIFICATIONS 34-5 LUBRICANTS 34-5 DIAGNOSIS 34-6 INTRODUCTION TO DIAGNOSIS
More informationOIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler
OIL COOLER KIT INSTALLATION INSTRUCTIONS PART NUMBER D570-0923 APPLICATION: 2011 E92 335is (N54 engine) with BMW M-Technic bumper and with stock oil cooler Congratulations for being selective enough to
More informationADJUSTABLE ANTI-ROLL BAR INSTALLATION INSTRUCTIONS PART NUMBER D PARTS LIST
ADJUSTABLE ANTI-ROLL BAR INSTALLATION INSTRUCTIONS PART NUMBER D120-0580 DESCRIPTION: Front 28mm; 3-hole adjustable APPLICATION: 2014-16 F22 228i/M235i 2015-16 F23 228i/M235i Convertible 2013-16 F30 320i
More informationPRODUCT SAFETY NOTICE DEALER/INSTALLER NOTICE
PRODUCT SAFETY NOTICE Congratulations. This vehicle has been equipped with a Firestone air suspension system. This suspension will enhance the vehicle s handling when loaded, however, the vehicle s performance
More informationAudi B8 A4/5, S4/5 and RS5 Coilover Installation Instructions
Audi B8 A4/5, S4/5 and RS5 Coilover Installation Instructions This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all
More information3.4 Adaptive Damping System (ADS II) with electronic level control Contents
Contents 3.4 Model 129 as of 09/95 Page Diagnosis Function Test................................... 11/1 Diagnostic Trouble Code (DTC) Memory................ 12/1 Complaint Related Diagnostic Chart...................
More informationPRODUCT SAFETY NOTICE
PRODUCT SAFETY NOTICE Congratulations. This vehicle has been equipped with a Firestone air suspension system. This suspension will enhance the vehicle s handling when loaded, however, the vehicle s performance
More informationIntake Manifold Tuning (IMT)
Page 1 of 11 24-154 Intake Manifold Tuning (IMT) system Notes: The change-over of the manifold from long to short intake path occurs at approx. 4500 RPM. Component location page 24-1 Required special tools
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION FASTENER TIGHTENING SPECIFICATIONS GENERAL SPECIFICATIONS...
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 FASTENER TIGHTENING SPECIFICATIONS 33-2 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 DIAGNOSIS 33-4 INTRODUCTION TO DIAGNOSIS
More informationElectronic Engine Power Control (EPC) (E-Gas), checking
Page 1 of 51 24-113 Electronic Engine Power Control (EPC) (E-Gas), checking E-Gas system, function For E-Gas, the throttle valve is not operated by a cable from the accelerator pedal. There is no mechanical
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS GMT 560 (4500/5500) CREW CAB (2351A000) Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 The CABMATE MODEL 2351A000 fits the 2003 and later GM 4500 / 5500 crew
More informationFRONT SUSPENSION GROUP CONTENTS GENERAL INFORMATION SPECIFICATIONS STRUT ASSEMBLY FRONT SUSPENSION DIAGNOSIS.
33-1 GROUP 33 FRONT SUSPENSION CONTENTS GENERAL INFORMATION 33-2 SPECIFICATIONS 33-3 FASTENER TIGHTENING SPECIFICATIONS 33-3 GENERAL SPECIFICATIONS 33-3 SERVICE SPECIFICATIONS 33-3 LUBRICANT 33-3 DIAGNOSIS
More informationPart # Mopar LX Level 1 Air Suspension System
Part # 13040199 05-14 Mopar LX Level 1 Air Suspension System Front Components: 1 1304409 Front RQ ShockWave Kit for Stock Lower Arms Rear Components: 1 13044099 Rear CoolRide Kit 1 13040709 RQ Series Rear
More informationH - TESTS W/O CODES INTRODUCTION SYMPTOMS
H - TESTS W/O CODES 1995 Volvo 850 1995 ENGINE PERFORMANCE Volvo - Trouble Shooting - No Codes 850 INTRODUCTION Before diagnosing symptoms or intermittent faults, perform steps in the F - BASIC TESTING
More informationPassenger s Side Airbag, On Board Diagnostic (OBD) Service
Subject: Model(s): Passenger s Side Airbag, On Board Diagnostic (OBD) All 2000 Group: Number: Date: 01 00 03 Apr. 24, 2000 Supersedes T.B. group 01 number 99 21 dated Dec. 8, 1999 Black revision bars indicate
More informationBMW-Motorrad - 0A01 - R 1200 GS, K Installing LED auxiliary headlights Preparatory work. Core activity
77 51 001 Installing LED auxiliary headlights + 77 51 502 Equipment trim-level variant: OA LED auxiliary headlights Note The LED auxiliary headlights have an overheat cutout. The headlights automatically
More informationCHAPTER 7 VAGABOND S HANDBOOK
CHAPTER 7 AIR PRESSURE/ HYDRAULICS SYSTEMS This chapter provides information on AIR pressure System, Brakes, Suspension, and Hydraulic Leveling Systems. More Details are found in the Maintenance Manual.
More informationFAX
INSTALLATION INSTRUCTIONS 6299 Air Suspension Kit (pat. pending) 2009+ Dodge 1500 Pickup with Rear Coil Springs Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationTOYOTA COROLLA/MATRIX LOWERING SPRINGS Preparation
Preparation Part Number: PTR40-02080 Kit Contents: Item # Quantity Reqd. Description 1 2 Front Springs 2 2 Rear Springs 3 1 Instruction Form Vehicle Service Parts (may be required for reassembly) Item
More informationLubrication system components, removing and installing
Page 1 of 33 17-1 Lubrication system components, removing and installing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once,
More informationBody, front. Lock carrier with attachments, removing and installing
Page 1 of 19 50-1 Body, front Lock carrier with attachments, removing and installing 1 - Hex bolt (6x) 45 Nm (33 ft lb) 2 - Hex bolt 45 Nm (33 ft lb) 3 - Hex bolt (4x) 10 Nm (7 ft lb) 4 - Hex bolts (2x)
More informationLAMPS 8L - 1 LAMPS CONTENTS
TJ LAMPS 8L - 1 LAMPS CONTENTS BULB APPLICATION... 16 HEADLAMP ALIGNMENT... 5 LAMP BULB SERVICE... 8 LAMP DIAGNOSIS... 1 LAMP SERVICE... 11 LAMP SYSTEMS... 15 LAMP DIAGNOSIS INDEX GENERAL INFORMATION GENERAL
More informationRemoving and installing dash panel insert
Removing and installing dash panel insert Caution To disconnect and connect the battery, the procedure described in the workshop manual should be strictly adhered to Chapter. Note Pull off multi-pin connector
More information2006 Porsche Cayenne SUSPENSION Level Control - Diagnostics - 9pa_Cayenne. Level Control - Diagnostics - 9pa_Cayenne
LEVEL CONTROL INTRODUCTION 2003-08 SUSPENSION Level Control - Diagnostics - 9pa_Cayenne NOTE: NOTE: The basic equipment of the Cayenne includes the level control module. The PASM function (Porsche Active
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Tow Hitch Wire Harness Kit Quest (2011) 999T8 NW000 Installation of this accessory requires installation of
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
ZJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 14 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationOWNERS MANUAL. GMC C K AND 19K GVW CHASSIS CAB 2004-NEWER MODELS (Link Part No. 8M000050) PROUDLY INSTALLED BY : COMPANY : INSTALLER SIGNATURE :
OWNERS MANUAL GMC C5500 15K AND 19K GVW CHASSIS CAB 2004-NEWER MODELS (Link Part No. 8M000050) Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 (712) 722-4868 Fax (712) 722-4779 QUESTIONS?
More informationMalfunction Criteria and Threshold Value Adaptive value. Secondary Parameters with Enable Conditions. >50.8 S Engine load 9-45% Delta fuel adaptation
DTC Error Message P0171 System Too Lean (Bank 1) Diagnostic Procedure Check fuel pump delivery and quantity. Refer to page 126. Check Fuel pressure regulator and residual pressure. Refer to Fuel Injection
More informationVolkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 19 Engine-Cooling system (Page GR-19)
19 Engine-Cooling system (Page GR-19) Cooling system components, removing and installing Continued coolant circulation pump (V51), checking Coolant hose connection diagram Coolant pump, removing and installing
More informationTOYOTA HIGHLANDER 2016 ON BOARD VACUUM CLEANER
2016 Part Numbers: 00016-48017- (01, 02, 04) Accessory Code: SV1000 NOTE: Will not work in Highlander HV Kit Contents Item # Quantity Reqd. Description 1 1 Vacuum Assembly 2 1 Hose Assembly 3 1 Tool Kit
More informationCylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
More information09-12 Dodge 4WD Leveling Kit
9235900 09-12 Dodge 4WD 1500 2.5 Leveling Kit Thank you for choosing Rough Country for all your suspension needs. DOES NOT FIT TRX PACKAGE VEHICLES!! Rough Country recommends a certified technician install
More information11. FRONT WHEEL/SUSPENSION/
11 FRONT WHEEL/SUSPENSION/ SERVICE INFORMATION------------------------------------------------ 11-2 TROUBLESHOOTING----------------------------------------------------- 11-3 HANDLEBAR ---------------------------------------------------------------
More information